P/N: 110401104880X

MAY.2018 REV. 2 UNI-T

UT210E
C£ Comply with European Union directives VII. LCD full view figure (Figure 2)
Mini Clamp Meters 2. Resistance/circuit on-off/diode/capacitance

Operation Manual m Application around and removal from UNINSULATED

HAZARDOUS LIVE conductors is permitted • Insert red meter pen into red jack (positive terminal), black meter

I. Overview n This symbol signify the product comply with both USA and
Canada requirement •
pen into black jack (COM terminal)
Connect meter pen in parallel to test piece for measurement
(Figure 4)
•
UT210E mini digital clamp meter features high reliability, safety,
precision and compact design. Its resolution ratio is 1mA. Maximum V.General standard Read measurement value from LCD screen.
range has maximum range of 100A AC/DC; particular VFC start 1. Maximum faulty operation protection voltage between input AWhen measure resistance/on-off/capacitance/diode range, do
mode. Entering this mode can accurately measure voltage and terminal and earthing is 600V. not input voltage over DC 60V or AC 30V to avoid injury to human.
current which has VFC frequency conversion. Voltage or current 2. Maximum overload protection for clamp head terminal:100A.
response display is true valid value. Whole range overload protection, 3.Maximum display: 2000Counts, update 2~3 times per second.
reliable measurement accuracy and unique appearance design Over range displays “OL”.
makes it an outstanding new generation functional electrician/ Diode: approx. 3.2V
electric power measurement instrument. Range: automatic (exclusive of electricity gear)
Polarity: automatic
II. Open case inspection Work temperature: 0°C ~40°C
Open the package and take out the instrument. Please check
whether the following accessories are missing or damaged. If any Relative humidity: 0°C~30°C:75%,30°C~40°C:50% Symbols
No. Instructions
item is missing or damaged, please contact your supplier immediately. Storage temperature: -10°C~50°C
1. Instruction manual 1 copy 4.Electromagnetic compatibility: 1 TRMS True valid value measurement status prompt
2. 1.5V AAA battery 2 pieces In 1 V/m radio frequency field: overall frequency=designated AC/DC voltage measurement prompt

—
2 AC/DC
3. Certification 1 copy precision+5% , radio frequency field above 1V/m has no designated
4. Probe assemblies 1 pair index. 3 Negative reading
5. Work altitude: 0~2000m Diode measurement prompt
6. Built-in battery: AAA 1.5V*2 pieces
4 -N-
7. Low battery: LCD displays “Q”. 5 •0) Circuit on-off measurement prompt
III. Safety precautions 8. Dimensions: approx, approx. (175x60x33. 5)mm , maximum
This Meter complies with EN 61010-1,61010-2-032,61010-2-033, clamp head size is 17mm. 6 m Data hold prompt
Pollution Degree 2, measurement category: (CAT II 600V, CAT III 300V) 9. Weight: approx. 170g (including battery) 7 Q kfi MQ Resistance unit: 0, kO, MQ
and Double Insulation standards.
VI. Product panel figure 8 Hz kHz MHz Frequency unit: Hz, kHz, MHz
Conforms to UL STD. 61010-1, 61010-2-032, 61010-2-033 Certified 3. AC/DC current measurement (Figure 5, Figure 6)
to CSA STD. C22.2 NO. 61010-1, IEC STD 61010-2-032, 1.Clamp head. 9 mV, V Voltage unit: mV, V
1)AC
61010-2-033 2.protective barrier.
1 0 mA , A Current unit: mA, A
• Select AC range (2A~,20A~, 100A~)
CAT II: Applicable to test and measuring circuits connected directly
to utilization points (socket outlets and similar points) of the low-
3.Clamp head trigger: pull the trigger to open clamp head.
4.NCV indicator: when the induced AC electric field intensity and 1 1 nF |i F mF Capacitance unit: nF, pF, mF • Open clamp head, hook electric wire (single wire), place electric
wire on geometric center indicated by clamp head, make sure
voltage MAINS installation. induction distance satisfy designated value, it will send out warning 1 2 (EF)NCV Noncontact AC voltage induction prompt the left and right clamp heads are totally closed. There is no gap
CAT III: Applicable to test and measuring circuits connected to the sound and flashes. between the left and right clamp heads.
•
1 3 Auto Auto range prompt
distribution part of the building’s low-voltage MAINS installation, 5.Function selection button: rotate this button to switch to corresponding Read measurement data from LCD.
before use and follow all safety instructions. 1 4 ZERO/REL Zero/relative measurement prompt 2)DC
••
functions indicated on the panel.
1.Use the clamp meter by following operation instructions, otherwise 6.HOLD/backlight key: for measuring readings/long press 2s to turn on Variable frequency voltage/current measurement prompt Press SELECT key to enter DC range (2Ais, 20Aji:, 100Am)
1 5 VFC
safety functions of the current clamp meter may fail to protect you. Press ZERO key before measurement to make readings zero.
or turn off backlight. Low built-in battery prompt
2.Abide by national safety laws and regulations. When operate in 16 Q If it does not return to zero after one press, then press it several
dangerous and live wire exposed environment, use personal 7.ZERO key: used for DCAzero, capacitance/voltage measurement times until the reading is zero. Note: as the product is highly
protection equipment to prevent accidents such as electric shock relative value. 17 0 Auto power-off prompt
sensitive, to ensure correct measurement data, direction of meter
and arc discharge. 8.SELECT key: select function mode, such as ACV/DCV, resistance/ during measurement should be the same as when it is in zero
3.Do not cross any position other than protective barrier of current on-off/diode/capacitance, ACA/DCA, etc. in AC voltage and current as much as possible.
clamp meter.
4.Before each use, check whether current clamp meter housing or
gear, long press this key for more than 2s to enter or exit VFC function.
9.LCD display screen : measurement function, symbol and numerical
VIII. Operation instructions
1 AC/DC voltage measurement
• Open clamp head, hook electric wire (single wire), place electric
wire on geometric center indicated by clamp head, make sure
output cable insulation cracks or damaged first, also check for value. • Select AC voltage or DC voltage gear the left and right clamp heads are totally closed. There is no gap
poor connected parts. Especially pay attention to insulating layer
around the clamping mouth. 10.Positive terminal input jack: when measure voltage, resistance/on-
off/capacitance/diode, red meter pen inserts into this jack.
• Insert red meter pen into red jack (positive terminal), black meter pen
into blackjack (COM terminal) •
between the left and right clamp heads.
Read measurement data from LCD. When the reading is positive,
5.Before removing the battery cover, please remove clamp meter
from all energized circuit and disconnect lead wire. 11.Input jack at COM terminal: when measure voltage, resistance/on- • Touch the test piece by red and black meter pen, for example, power
socket (Figure 3).
it means current flows from positive end indicated by clamp head
to the negative end. Negative reading is the opposite.

•
6.Do not use clamp meter in circuit with voltage higher than 600V off/capacitance/diode, black meter pen inserts into this jack.
Read measurement value from LCD screen. A When measure current, unplug test pen to avoid electric shock.
this or frequency higher than 400Hz.
/.Measurement category class is CAT II 600V/CAT III 300V, pollution AWhen measure voltage, maximum input voltage is 600V (AC/DC),
degree is 2. Do not use it out of scope. do not exceed this limitation, otherwise it may cause electric shock
8.Be cautious when work in environment with exposed wire. Contact
with wire may result in electric shock.
9.For voltage above 60V DC (direct current), 30V AC (AC effective
value) or 42V AC (peak value), such voltage may cause electric
shock.
10. Probe assemblies used for MAINS measurements CAT II 600V
/CAT III 300V according to IEC 61010-031, If you want to replace
the probe assemblies and they need the same level CAT II 600V
/CAT III 300V or better level. Protection impairment if used in a
manner not specified by the manufacturer.
11.Function switches shall be set at the correct position prior to
measurement. It is forbidden to perform gear conversion in
measurement to guard against damage to the meter.
V.EIectrical symbol
a Low battery A Warning •o) Buzzing on-off
V£ ACV/DCV -H- Diode Earthing
ACA/DCA 0 Double insulation
A Danger! High voltage Figure 3 Figure 5
 UNI-T
SELECT key, then power-on start, you will heard 5 buzzing which 3.Resistance measurement X. Maintenance and repair
means automatic power-off function is cancelled. Turn off and
restart the machine, automatic power-off function will be recovered.
Range Resolution Accuracy A Warning: before remove rear cover of the instrument, make

•
sure power supply is off; meter pen leaves input port and circuit-
200.00* 0. 1 Q
The buzzer will send out 5 warnings 1 minute before automatic power under-test .
off. A long buzz will be heard before power off. When automatic power 2.000kQ 1Q
±(1.0%+2) 1.General maintenance and repair
-off function is canceled, you will hear 5 continuous warnings in every 20.00kQ 10 Q * For maintenance and repair, use wet cloth and mild cleaner to
15 minutes. clean instrument cover, do not use grinding agent or solvent.
200. OkQ 100 Q
• Buzzer : press any key or rotate function switch,if such function key
is valid, buzzer will “beep” once (lasting approx. 0.25s). In gear ,
2.000MQ 1k Q
±(1.2%+3)
* If the instrument is abnormal, stop use it and maintain.
* If it is necessary to verify or maintain the instrument, maintain it
by qualified professional serviceman or designated maintenance
when the circuit-under-test is conductive (<10Q),buzzer makes 20.00MQ 10k Q
department.
sound continuously. When measure voltage or current outrange, A Range: measured value=measurement display value-meter pen 2.Replace battery (see Figure 8)
buzzer will “Beep” to warn outrange, function status is as below: short circuit value * When LCD displays under-voltage a prompt, replace built-in
a)When AC, DC voltage >600V, buzzer beeps Open-circuit voltage is about 1V battery immediately otherwise it will affect measurement accuracy.
b) 100AAC and DC gear: current > maximum range, buzzer beeps . Overload protection: 600V-RMS * Battery specification: AAA 1,5V x2cells
4. •»» circuit on-off, -N- diode measurement
• Low-voltage detect: when battery voltage is lower than 2.5V, battery
under-voltage symbol Qappears, measurement accuracy may be
Range Resolution Remarks
lower once this symbol shows, replace battery timely; if it is lower Resistance value for circuit disconnect: > 1500 ,
•») 0.1Q buzzer makes no sound;
than 2.2V, only battery under-voltage symbol shows after starting up, Resistance value for circuit conduct: < 10O,
it can’t work. buzzer beeps continuously.
•
Figure 6
When battery supply voltage lowers to 2.6 V, LCD backlight will be in Open circuit voltage is 3.2V: normal voltage for
4. NCV noncontact electric field measurement (Figure 7) weak or non-start state; but measurement functions still work. -H- 1mV silicon PN junction is 0.5-0.8V.
If you want to measure whether there is AC voltage or
electromagnetic field, place front end of clamp head 8~15mm IX. Technical index A Overload protection: 600V-RMS
close to the test piece, analog quantity of inductive AC voltage Accuracy: ±(a% reading + b word count), warranty period is 1 year. 5. Capacitance measurement
is about voltage 100V, display “EF”, > critical voltage Environment temperature:230C±5°C(73.4°F±9°F) relative humidity: =575%
Range Accuracy
100V, display —
it has four “ ” levels based on voltage size 1.DC voltage measurement
Resolution
with different buzzing at each level, with NCV light flashing to 2nF 1pF ± (4 % + 1 0 )
discriminate electric field intensity. Range Resolution Accuracy
20.00nF~200.0pF 1 0pF~1OOnF ±(4%+5)
ranges switch NCV measurement, please unplug the test 200.OmV 0.1mV ± (0.7% +5)
2.000mF~20.00mF 1pF~1OgF ±10%
pen to avoid electric shock . 2.000V 1mV
A Overload protection: 600V-RMS
20.00V 10mV <1pF measured capacitance, it is suggested to use ZERO
L 200.0V 100mV
±(0.7%+3)
measurement mode to ensure accuracy.
Figure 8

6. DCA measurement
600V 1V Operation procedure:
Range Resolution Accuracy 1.Place power switch on “off’ position and remove meter pen from
A Input resistance is about 10MQ. (as input resistance is high, when
2.000A 1mA ± (2%+8) input jack .
200mV range open circuit, there may be instable digital display, 2.Unscrew the screw fixed on the rear cover of battery by screwdriver,
20.00A 10mA ± (2%+3) remove battery rear cover and take out old battery as shown in
but measurement can be stabilized once the measured source with the figure.
internal resistance lower than 10MQ is connected, but the impact 100.0A 100mA ± (2%+3) 3.Replace 2 pcs of new batteries (specification AAA1.5V)
of internal resistance of measured source on measurement reading
should be considered)
A Overload protection 100A This instruction manual is subject to change without further notice.
As external electromagnetic field such as the earth exists,
A Maximum input voltage: ±600V to ensure accuracy of measurement reading, press ZERO key
before measurement to make readings be zero. If it is not zero
2. AC voltage measurement after one press, press it for several times until reading is zero.
Direction of meter during measurement should be the same as
Range Resolution Accuracy
when it is in zero as much as possible.
2.000V 1mV 7.ACA measurement
±(1.0% + 3)
20.00V 10mV Range Resolution Accuracy
±(1.0%+3) ± (3%+10)
200.0V 100mV
V.F.C. mode: ± (4.0%+3) 2.000A 1mA V.F.C mode: ± (4.0%+10)
±(1.2%+3) ±(2. 5%+8)
600V 1V 20.00A 10mA V.F.C mode: ± (4.0%+10)
V.F.C. mode: ± (4.0%+3)
± (2.5%+5)
A Input resistance: 10 MQ in average. 100.0A 100mA
V.F.C mode: ± (4.0%+10)
5 Other functions AMaximum input voltage: 600Vrms
• Long press HOLD key for 2s to turn on or turn off LCD backlight
• Show true virtual value. Frequency response: 45- 400Hz Overload protection 100A UNI-T
• residue
function.
• Automatic power-off: when measuring, if the rotary button has
not pulled out in 15 minutes, the instrument will automatically
Accuracy guarantee range: 5-100% range, short circuit allows <10
readings.
• Accuracy warranty coverage: 5-100% range, 2Aopen circuit
allows <20 residue readings.
UNI-TREND TECHNOLOGY (CHINA) CO., LTD.

• Non-sinusoidaltruewavevalidcounts
No6, Gong Ye Bei 1st Road,
power off to save energy. In automatic power-off mode, turn
rotary button to OFF and restart the machine, or click any key • Non-sinusoidal wave counts add error by crest factor:
When crest factor is 1-2: Add 3%.
Displays are value. Frequency response: 50~60Hz.
• a) When crest factor is 1-2: Add 3%.
add error by crest factor:
Songshan Lake National High-Tech Industrial
Development Zone, Dongguan City,
to wake the instrument. Guangdong Province, China

•
When crest factor is 2-2.5: Add 5%. b) When crest factor is 2-2.5: Add 5%. Tel: (86-769)8572 3888
Turn off automatic power-off function: press and hold When crest factor is 2.5-3: Add 7%. http://www.uni-trend.com
c) When crest factor is 2.5-3: Add 7%.