Crushers with 32 Way Receiver Fault Codes: (Format Cxxxx)

Code Fault
C0001 ESTOP
C0002 Remote Stop activated by handset
C0003 Communication problem - Engine interface unit not receiving messages from rest of crusher electronics
C0004 Communication problem - Engine interface unit not receiving messages from CAT engine
C0005 Communication problem - Crusher electronics is not receiving any messages from 32way receiver
C0006 Communication problem - Crusher electronics is not receiving any messages from analog sensor box
C0007
C0008 Communication problem - Crusher electronics is not receiving any messages from daisy chain box

C0009 Communication problem - Crusher electronics is not receiving any messages from track led box
C0010 Communication problem - Crusher electronics is not receivng any messages from motorised valve unit
C0011
C0012
C0013 Impactor, conveyor sensor is picking up problem, disabled feeder
C0014 Impactor, Box switch is open, all service but track are disabled
C0015 Crusher electronics is performing SKF vibration analysis test (duration 60 seconds)
C0016 Crusher electronics is seeing a problem with switch matrix, stuck button / shorted wires

C0017 C10+/C12+ Trying to start jaw but receiving bent toggle plate signal, check toggle plate switch
C0018 Crusher electronics has picked up excessive vibration during test. Shutdown crusher and check bearing
C0019 Crusher electronics is destroking hydraulic pump to relieve excess pressure.
C0020 Crusher electronics has stopped crusher unit due to excessive pressure, pump already destroked.
C0021 C12+ crusher electronics is picking up low grease signal from vogel unit.
C0022 C10+/C12+ 100 Bar pressure switch is open
C0023 Motorised valve unit is not connected to motor
C0024 Motorised valve unit is not seeing motor turning, possibly jammed motor, faulty wiring.

Machine Type
X44 C12+ Screener+
C0025 Electrical problem with CCB output0, dependent on machine: Vibration warning lamp
C0026 Electrical problem with CCB output1, dependent on machine: Feeder Slower lamp
C0027 Electrical problem with CCB output2, dependent on machine: Feeder Faster lamp
C0028 Electrical problem with CCB output3, dependent on machine:
C0029 Electrical problem with CCB output4, dependent on machine:
C0030 Electrical problem with CCB output5, dependent on machine:
C0031 Electrical problem with CCB output6, dependent on machine: Jaw block permanent feed, White Tape
C0032 Electrical problem with CCB output7, dependent on machine: Engine Stop Engine Stop Engine Stop
 Machine Type
X44 / X38 C10+ / C12+ / I-C13 Screener+
Valve, Ident, Wire Colour/No. Valve, Ident, Wire Colour/No. Valve, Ident, Wire Colour
C0033 Electrical problem with Receiver output0, dependent on machine: PCO,L2, Purple Jaw Dump, Slate Tape, Purple Tail Conveyor
C0034 Electrical problem with Receiver output1, dependent on machine: Mid Conveyor
C0035 Electrical problem with Receiver output2, dependent on machine: Manual Tramp, R3, Green/Yellow Jaw Adjust, Red Tape, Blue Fines Conveyor
C0036 Electrical problem with Receiver output3, dependent on machine: Lube Oil Cooler, Brown Finger Feeder
C0037 Electrical problem with Receiver output4, dependent on machine: Accumulator Hold, R1, Blue/White Accumulator, Brown/White Tape, Brown Grid Up
C0038 Electrical problem with Receiver output5, dependent on machine: Lube Pump, Slate Grid Down
C0039 Electrical problem with Receiver output6, dependent on machine: Clamp Ring Release (not hosed), L3, Blue I-C13 Recirc Conveyor Grid Dump
C0040 Electrical problem with Receiver output7, dependent on machine: Lube Pre Heat, Blue

C0041 Electrical problem with Receiver output8, dependent on machine: Accumulator Hold, L1, Brown I-C13 Screen Box
C0042 Electrical problem with Receiver output9, dependent on machine: Screen Box, No Tape, 2 Side Conveyor, Brown Tape, 1
C0043 Electrical problem with Receiver output10, dependent on machine: Main Converyor, Red Tape, 4 Main Conveyor, Red Tape, 11
C0044 Electrical problem with Receiver output11, dependent on machine: Recirc Converyor, White Tape, 5 Magnet/Recirc Conv, White Tape, 5
C0045 Electrical problem with Receiver output12, dependent on machine: Feeder, Brown Tape, 1 Auxillary Pump/Screen Box, No Tape, 2
C0046 Electrical problem with Receiver output13, dependent on machine: Reverse Crusher, Slate Tape, 9
C0047 Electrical problem with Receiver output14, dependent on machine: Cone Drive, Green Tape, 8 Forward Crusher, Green Tape, 8
C0048 Electrical problem with Receiver output15, dependent on machine: Destroke pump valve Destroke pump valve

C0049 Electrical problem with Receiver output16, dependent on machine: Tracking valve, destroke pump, Tracking valve, destroke pump,
C0050 Electrical problem with Receiver output17, dependent on machine: I-C13 Recirc Conveyor ScreenBox
C0051 Electrical problem with Receiver output18, dependent on machine: Cone gap adjust, R5, Orange Jaw Wedge Out, Blue/White Tape, Pink Boost Feeder
C0052 Electrical problem with Receiver output19, dependent on machine: Slew feeder, L5, Yellow
C0053 Electrical problem with Receiver output20, dependent on machine: Cone gap adjust, R6, White/Red Jaw Wedge In, Brown Tape, Yellow Left Track Forward
C0054 Electrical problem with Receiver output21, dependent on machine: Slew feeder, L6, Pink Left Track Reverse
C0055 Electrical problem with Receiver output22, dependent on machine: Clamp main cylinders, R4, Blue/Yellow Jaw Clamp, Yellow Tape, Slate Right Track Forward
C0056 Electrical problem with Receiver output23, dependent on machine: Locking ring clamp, L4, Slate Right Track Reverse

C0057 Electrical problem with Receiver output24, dependent on machine:

C0058 Electrical problem with Receiver output25, dependent on machine: Lube Oil Cooler2 Feeder, Green/Yellow Tape, 1
C0059 Electrical problem with Receiver output26, dependent on machine: Main Conveyor lift, Yellow tape, 14 Main Conveyor lower, Blue tape, 15
C0060 Electrical problem with Receiver output27, dependent on machine: Main Conveyor lower, Blue tape, 15 Main Conveyor lift, Yellow tape, 14
C0061 Electrical problem with Receiver output28, dependent on machine: Left track forward, 10 Left track forward, 10
C0062 Electrical problem with Receiver output29, dependent on machine: Right track forward, 12 Right track forward, 12
C0063 Electrical problem with Receiver output30, dependent on machine: Left track reverse, 11 Left track reverse, 11
C0064 Electrical problem with Receiver output31, dependent on machine: Right track reverse 13 Right track reverse 13

C0128 Metal Detected, feeder will be switched off, reset metal detector
C0129 TASS speed sensor on main conveyor is turning at less than 10m/min. Feeder will be disabled
C0130 Pump Pressure transducer not connected