Scribd
Upload
39 views

Discharge Measurement

This document provides guidance on measuring discharge and estimating water flows from various sources to design rural water supply schemes. It describes several methods for measuring discharge, including using a bucket and stopwatch, floats to measure stream velocity, and portable weirs. Estimating techniques are outlined using spot measurements, rainfall/catchment area data, and Manning's equation. Constant flows from boreholes or pipes can be measured using weirs, orifice plates, or measuring pipe trajectories.

Uploaded by

GRACE DONGON
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
39 views

Discharge Measurement

This document provides guidance on measuring discharge and estimating water flows from various sources to design rural water supply schemes. It describes several methods for measuring discharge, including using a bucket and stopwatch, floats to measure stream velocity, and portable weirs. Estimating techniques are outlined using spot measurements, rainfall/catchment area data, and Manning's equation. Constant flows from boreholes or pipes can be measured using weirs, orifice plates, or measuring pipe trajectories.

Uploaded by

GRACE DONGON
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

27.

Discharge measurements
and estimates
Introduction

Community water-supply schemes are generally designed for water consumption in the approximate range of 15 to 60
litres per person per day. Allowance has also to be made for water use by livestock, for future growth in population and
demand, and for losses of water by leakage etc. from the system.

It is important to check that the discharge of the source is enough, throughout the year, to meet the community’s
requirements. This requires measuring or estimating the dry season flow, when least water will be available.

If a small reservoir is to be built, more detailed flow data are needed:

 Year round flows, to size the storage


 Flood flows, to design the spillway

Useful conversion factors

One litre per second = 1 I/s One cubic metre = 1000 litres

= 86 400 litres per day One Imp gallon = 4.546 litres

One US gallon = 3.785 litres

Ways to measure the flows of springs and small streams

Bucket and stopwatch


In this method, all the flow from a spring or small stream is collected in a container whose volume is known (e.g. a
bucket, jerrycan, 200-litre drum) and the time to fill the container is measured. The filling time should be more than
five seconds, to give reasonable accuracy.

Discharge or yield (I/s) = volume (litres)/time (seconds)

Stopwatch

Oil drum

An oil drum below


below a bamboo
bamboo spout
DISCHARGE MEASUREMENTS AND ESTIMATES

Float, stopwatch and tape


Floats are a simple way of measuring the velocity of a stream, but they are not very accurate. The surface
velocity is obtained by measuring the time (t secs) for a float to travel a measured distance (L metres). It is
best to choose a straight, uniform river section about 30m long, and to time the float over a number of repeated t runs.
A piece of fruit makes a good float, as it is less affected by wind than a wooden stick. A factor of about 0.85 should be
used to convert surface velocity to average velocity.

Surface velocity (m/s) = L/t

Average velocity (m/s) = 0.85 x L/t

The cross section of the stream should be measured up carefully in a number of places along the test
distance, and the average cross-sectional area calculated (A sq m).

Discharge (cubic metres per second)

= average velocity x cross sectional area of stream

= 0.85 x (L/t) x A

Discharge (L/s) = 1000 x 0.85 x (L/t) x A:

A1 L
Float

Flow

A2

A river with measurement stations and sections

Weir with stick gauge


Portable weirs made of steel plate can be used for measuring the flow of small streams or springs. They can give
accurate measurements, if they are installed carefully. The weir should be set vertically, perpendicular to the stream,
and with the crest horizontal. A free fall is required over the weir crest. Leaking must be prevented around the sides of
the weir, possibly by using a polythene sheet.

A stick gauge, marked in centimetres, is set vertically at the side of the stream upstream of the weir. It is used to
measure the head, h (m), which is the difference between the upstream water level and the crest of the weir. It is
important to check that the gauge zero is truly at weir-crest height. This may be done using a spirit level and string line,
or water-filled flexible plastic tubing.

There are different shapes of weir, each of which has a standard formula for calculation of discharge.
Details for two common weir shapes are given opposite.
DISCHARGE MEASUREMENTS AND ESTIMATES

Section through either weir showing


maximum flow velocity and minimum
dimensions

Rectangular weir Triangular weir (900 notch) Note: Weir plate should be as thin as
possible and sharp edged. A thin plate can
be fixed around the notch to achieve this.)

Two common weirs


where Q = discharge over weir (m3/s), L = length of notch (as defined in ffigure,
igure, in m) and h = head ((m)
m)

Estimating flows of small streams

Possible sources of information for estimating the range of flows are:


a) local knowledge
b) observation and survey
c) rainfall records
d) size of catchment area
e) spot measurement of discharge

It is important to take account of other users, both upstream and downstream.

Possible ways of estimating flows in the dry season are:


a) From spot measurements during the dry season. This is the best way.
b) From spot measurements at other times of year,
either, reduced by suitable factors derived from experience on similar river basins
or, plotted against time on a graph, and extrapolated to the dry season. Records from measurement on similar
river basins can be used to derive a typical shape for the graph.
c) From any records of flows in a similar river basin nearby, with similar rainfall, by using the following method:

 for the recorded basin, measure the catchment area A1


which drains to the measurement station;

 for the unrecorded basin measure the catchment area


A2 which drains to the point where the flow is to be
estimated;

 obtain the dry season flow Q1 for the recorded basin;

Q1 (known) Q2 (not known)  the dry season flow Q2 for the unrecorded basin can
then be estimated as: Q2 = Q1 x A2/A1.
DISCHARGE MEASUREMENTS AND ESTIMATES

d) From local reports (or records) of dry season depth, coupled with survey of the cross section and slope of the
stream, and using the Manning equation:

Constant discharges from boreholes or pipes

These may be measured by one of the following methods:


1. Using a V-notch weir set in a steel tank or earth channel
2. Using a calibrated orifice plate and pressure gauge on an upstream tapping (the pressure difference across an
orifice plate will depend on the flow rate)
3. Measuring the co-ordinates of the water trajectory from a horizontal pipe, as shown below.

Measurement of flow from a horizontal pipe

Water flow from horizontal pipes (litres/second) flowing completely full at the end

Further information:
Cairncross, S. and Feachem, R., Small water supplies, Ross Institute Bulletin No.10, 1978.
Herschy, R. W., Stream flow measurement, Eisevier, 1985.

Text: Ian Smout


Illustrations and design: Rod Shaw
WEDC, Loughborough University, Loughborough, Leicestershire LE11 3TU, UK.

You might also like