r

h
a
F
s
n
m
ie
S

RAD/FLUORO
AX

Adjustment
System

3DV Ceiling Stand

07042034
07042018

© Siemens 2009
The reproduction, transmission or use
of this document or its contents is not
permitted without express written
authority. Offenders will be liable for
damages. All rights, including rights
created by patent grant or registration
of a utility model or design, are
reserved.

Print No.: AXRF-000.842.01.01.02 English

Replaces: n.a. Doc. Gen. Date: 05.09
2 Revision / Disclaimer
1Revision / Disclaimer

Document revision level

The document corresponds to the version/revision level effective at the time of system
delivery. Revisions to hardcopy documentation are not automatically distributed.
Please contact your local Siemens office to order current revision levels.

Disclaimer
The installation and service of equipment described herein is to be performed by qualified
personnel who are employed by Siemens or one of its affiliates or who are otherwise autho-
rized by Siemens or one of its affiliates to provide such services.
Assemblers and other persons who are not employed by or otherwise directly affiliated with
or authorized by Siemens or one of its affiliates are directed to contact one of the local
offices of Siemens or one of its affiliates before attempting installation or service proce-
dures.

RAD/FLUORO AXRF-000.842.01.01.02 Page 2 of 44 Siemens

05.09 CS PS AX R/F
Table of Contents 3
0Table of Contents

1 _______ General Information______________________________________________ 4

Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Required Aids and Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
General Remarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Tolerance Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Torque Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
System Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Polydoros Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Service Radiation Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Product-specific Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Additionally Required Documents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2 _______ Check and Adjustment __________________________________________ 14

Central Beam Drift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Parallelism of the X-ray Tube to the Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Light Field/Radiation Field on the Collimator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Wobbling of the Support Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Tube Unit Drift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Aligning the Collimator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Spring-loaded Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Adjusting the Weight Compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Potentiometers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Adjustment of the Potentiometer for the transverse Axis (only Fully Synchronized Sys-
tem). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Vertical Axis Brake Gap (RVA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Horizontal Axis Brake Gap (RHA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Transverse and Longitudinal Carriage Brake Gap (only Fully Synchronized System) .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Detent Forces (only Fully Synchronized System). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Stop Assembly (only Fully Synchronized System) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

3 _______ Final Work Steps _______________________________________________ 39

Adjusting in the SSW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Checking Central Beam Drift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Bucky Wall Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
IQAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

4 _______ Changes to Previous Version _____________________________________ 43

5 _______ Index _________________________________________________________ 44

Siemens AXRF-000.842.01.01.02 Page 3 of 44 RAD/FLUORO

05.09 CS PS AX R/F
4 General Information
1-
Requirements
1General Information

Required Aids and Tools 0

All tools, measuring equipment and aids, with the exception of the "standard installation
tool kit", are listed and specified in the Service Tools Catalogue.

• Torque wrench, up to 12 Nm 34 30 063

• Digital spirit level n.a.
• Feeler gauge 80 38 259
• Spring balance, 100 N 44 29 122 MH029
• Loctite 243 55 07 038

RAD/FLUORO AXRF-000.842.01.01.02 Page 4 of 44 Siemens

05.09 CS PS AX R/F
General Information 5

General Remarks 1.1

Tolerance Data 0

General tolerances for linear dimensions in accordance with ISO 2768

These tolerances apply to all dimensions indicated in these instructions, unless other tol-
erances are specifically indicated after the value.

Limit value for over 3 mm over 6 mm over 30 over 120 over 400 over 1000 over 2000
the nominal to 6 mm to 30 mm mm to 120 mm to 400 mm to mm to mm to
range mm mm 1000 mm 2000 mm 4000 mm
Adm. toler- ± 0,5 mm ± 1 mm ± 1,5 mm ± 2,5 mm ± 4 mm ± 6 mm ± 8 mm
ance

Torque Values 0

Nominal Screw material Steel per DIN 267 Brass CuZn

thread diame- alloy
ter
Hardness rating 4.6 4.8 5.8 8.8 10.9 12.9
M3 0.5 0.67 0.83 1.3 1.9 2.2 0.62
M 3.5 0.76 1.0 1.3 2.0 2.2 3.4 0.95
M4 1.1 1.5 1.9 3.0 4.2 5.1 1.4
M5 2.2 3.0 3.7 6.0 8.4 10.1 2.8
M6 3.8 5.1 6.4 10.2 14.4 17.3 4.8
M8 9.5 12.6 15.8 25.3 35.6 42.7 11.9
M 10 18.7 24.8 31.1 49.8 70.0 84.0 23.3
M 12 32.9 43.8 54.8 87.6 123.3 147.9 41.1

A tolerance of 10% is permissible for torque values.

Siemens AXRF-000.842.01.01.02 Page 5 of 44 RAD/FLUORO

05.09 CS PS AX R/F
6 General Information

Notes 1.2

System Safety Information 0

When performing the work steps and checks, the general safety information for medical
products must be observed. (TD00-000.860.01 / General Safety Notes)

NOTE Work on the system may be performed only by trained per-

sonnel.

General Safety Information

WARNING Observe the Safety Information!

If not observed, death or serious bodily injury can occur.
¹ When performing the work steps and tests, the prod-
uct-specific safety information contained in the docu-
ments as well as the general safety information for
medical products must be observed.

UPS Safety Information for the Image System

UPS = Uninterruptable Power Supply.

WARNING Observe the Safety Information!

If not observed, death or serious bodily injury can occur.
Even if power has been swiched off to the complete X-ray
system with the on-site On/Off switch and this has been
secured against unintentional switch-on, there is still line
power present on the FL-C PC and on one or more monitors.
¹ When performing work steps on the FL-C and on the
monitors, the UPS must be switched off and the "OUT-
PUT" connector on the back of the UPS must be dis-
connected.

RAD/FLUORO AXRF-000.842.01.01.02 Page 6 of 44 Siemens

05.09 CS PS AX R/F
General Information 7

Polydoros Safety Information 0

WARNING Observe the safety information!

If not observed, death or serious bodily injury can occur.
¹ When performing the work steps and tests, the prod-
uct-specific safety information contained in the docu-
ments as well as the general safety information for
medical products must be observed.

WARNING A Gigalink (Class kx3A product) with a laser diode is used for
image transfer between the FD --- PIX Box --- image system.
The laser beam is dangerous for the human eye.
¹ Do not look into the laser beam. The laser beam is not
visible.

WARNING Appropriate radiation safety measures must be provided

while performing this work.
If not observed, death or serious bodily injury can occur.
¹ Checks and settings that need to be performed with
X-ray radiation switched on are identified by the radia-
tion warning symbol x .

WARNING Unwanted radiation

If not observed, death or serious bodily injury can occur.
¹ To prevent unintentional triggering of high voltage or
radiation, set the SS switch (S1) on the D600 to OFF (1)
(Fig. 1 / p. 9).

CAUTION Damage to the D600 board.

¹ The D600.X222 and D600.X223 CAN connections and
the "CAN IN" and "CAN OUT" CAN on the connector
panel (Fig. 1 / p. 9) may not be unplugged or plugged in
while under power.

WARNING Prior to beginning work, make absolutely sure to switch off

power to the particular assembly:
If not observed, death or serious bodily injury can occur.
¹ Completely switch power off to the entire X-ray system
at the on-site on/off switch and secure it against unin-
tentional switch-on.

Siemens AXRF-000.842.01.01.02 Page 7 of 44 RAD/FLUORO

05.09 CS PS AX R/F
8 General Information

WARNING Line power is present!

If not observed, death or serious bodily injury can occur.
¹ After switching off the F1 power switch, the input termi-
nals still cond8uct voltage to X1, X2, F2, K3. The follow-
ing points conduct voltage with the generator switched
off and the system switched on: F1, F2, F4-F10, K1, K2,
K4, K5, K6, T1, T3, X1-X4, X7-X10, Z1, Z2. See the "Cau-
tion!" label in the generator.

WARNING Intermediate circuit voltage is present!

If not observed, death or serious bodily injury can occur.
¹ After switching off the generator, there is still approx.
600 V DC voltage present at the D510, D115 and D480
inverter! This is indicated by the V121 and V122 LEDs
on the D510. The voltage dissipates in approx. 2 min-
utes to < 30 V; the LEDs go off at approx. 30 V.

WARNING Opening the Pivot Frame

If not observed, death or serious bodily injury can occur.
¹ Prior to loosening the nuts (A/Fig. 1 / p. 9) and opening
(swinging out) the pivot frame, make absolutely sure to
switch off the generator and wait a min. of 2 minutes
until the intermediate circuit voltage is less than 30 V.

RAD/FLUORO AXRF-000.842.01.01.02 Page 8 of 44 Siemens

05.09 CS PS AX R/F
General Information 9

Fig. 1: Safety Note

Service Radiation Switch 0

Service Switch in the Normal Position

Tab. 1 Service_Switch

Name 1 Switch Position LED

SS switch D600.S1 ON / "Position 2" V29 OFF
Service Mode D600.S2 OFF / “Position 1” V8 OFF
mAs Meas D600.S5 OFF / “Position 1” V109 OFF
Power On / Off D611.S1 ON / "Position 2"
Service Radiation Switch D611.S3 OFF / “Position 2” V70 /V76 OFF
HW release switch for X-ray.
Udc disable D611.S4 ON / "Position 2"

1. For details, see Wiring Diagram AX.......

SS_Switch, D600.S1
See (Fig. 1 / p. 9)

Siemens AXRF-000.842.01.01.02 Page 9 of 44 RAD/FLUORO

05.09 CS PS AX R/F
10 General Information

ON = Position 2 Normal mode / LED D600.V29 = OFF

OFF = Position 1 Spark pulses are not transferred to the main inverter; no high voltage
is generated. LED D600.V29 = ON.

Power On / Off, D611.S1

See (Fig. 1 / p. 9)

ON = Position 2 Normal mode, the generator can be switched on via the system
switch-on circuit.
OFF = Position 1 The generator is switched off and cannot be switched on via the sys-
tem.

S2 Switch-on Button, D611.S2

See (Fig. 1 / p. 9)

Not pressed Normal operation

pressed n.a.

S4 UDC Disable Switch, D611.S4 (no Intermediate Circuit Voltage)

See (Fig. 1 / p. 9)

ON = Position 1 No intermediate circuit voltage. When there is a switch-over,

there is always a reboot of the
generator.
OFF = Position 2 Normal operation The error
Intermediate circuit voltage too
low is entered into the error log.

Service Radiation Switch, D611.S3

See (Fig. 1 / p. 9)

OFF = Position 2 Normal operation

ON = Position 1 HW release switch for X-ray.

D600.S5 mAs Meas. Switch

See (Fig. 1 / p. 9)

OFF = Position 1 Normal operation

ON = Position 1 The tube current can be measured at the D600 mA_Meas test
points.

RAD/FLUORO AXRF-000.842.01.01.02 Page 10 of 44 Siemens

05.09 CS PS AX R/F
General Information 11

Product-specific Information 1.3

Depending on the version, the illustrations and drawings can show slight differences to the
shipped unit and should therefore be viewed only as examples.

Siemens AXRF-000.842.01.01.02 Page 11 of 44 RAD/FLUORO

05.09 CS PS AX R/F
12 General Information

Prerequisites 1.4

Additionally Required Documents 0

• Tube Stand Replacement of Parts See the system CB-DOC.

• System Online Help See the system CB-DOC.
• Collimator Adjustment See the system CB-DOC.

RAD/FLUORO AXRF-000.842.01.01.02 Page 12 of 44 Siemens

05.09 CS PS AX R/F
General Information 13

Abbreviations 1.5

SSW Service software

Ysio F Ysio Fully Automated System
Ysio S Ysio Fully Synchronized System

Siemens AXRF-000.842.01.01.02 Page 13 of 44 RAD/FLUORO

05.09 CS PS AX R/F
14 Check and Adjustment
2-
Central Beam Drift
2Check and Adjustment

If there are changes to the ceiling stand, e.g. caused by a replacement or removal of differ-
ent components, a check of the system and possibly a new adjustment is required.

Parallelism of the X-ray Tube to the Table 0

Must be performed with

• a new table.

Check

1. Position the ceiling stand over the table so that when the light localizer is switched on,
the front edge of the table is lined up with the center of the light cross.
2. Move the stand in the longitudinal direction over the complete length of the table.
3. If the table is aligned, it should move parallel to the center of the light cross. The toler-
ance over the entire length of the table is ± 2 mm.

Adjustment

1. Turn the table at one end until parallelism to the central beam is established over the
entire movement range.

Light Field/Radiation Field on the Collimator 0

Must be performed following

• replacement or removal of the collimator
• replacement or removal of the tube unit.

Check
• Check the difference between the light and radiation fields. The position of the light field
can be readjusted at the collimator.

Adjustment
The adjustment can be found in the CB-Doc under Collimator > Adjustment
(AX74-020.842.01).

Wobbling of the Support Arm 0

Wobbling of the support arm must be checked following

• replacement of the support arm
• removal of the support arm, e.g. following replacement of the suspension of the vertical
axis or of the spring-loaded mechanism.

RAD/FLUORO AXRF-000.842.01.01.02 Page 14 of 44 Siemens

05.09 CS PS AX R/F
Check and Adjustment 15

Check

1. Position the 3D in the center of the room, between the two transverse and longitudinal
rails.
2. Remove the cover panels on the rear of the support arm (Fig. 2 / p. 15) that cover the
column.

Fig. 2: Suspension of support arm Fully Automated System

3. With a digital spirit level, check whether the support arm is level in the longitudinal and
transverse directions.
The tolerance is ± 0.1 °.

Fig. 3: Checking wobbling in the transverse Fig. 4: Checking wobbling in the longitudinal
direction of the support arm direction of the support arm

¹ If the result is not within the tolerance, wobbling of the support arm must be
adjusted.

Siemens AXRF-000.842.01.01.02 Page 15 of 44 RAD/FLUORO

05.09 CS PS AX R/F
16 Check and Adjustment

Adjustment
Adjustment is made using the wobbling screws. The wobbling screws are comprised of a
securing screw (Allen screw) (1/Fig. 5 / p. 16) and an adjustment screw (hex screw)
(2/Fig. 5 / p. 16).

Fig. 5: Wobbling screw

Pos. 1 Securing screw (Allen screw)
Pos. 2 Adjustment screw (hex screw)

1. Loosen the two Allen screws (1/Fig. 6 / p. 16) and (1/Fig. 7 / p. 16) (approx. 4 turns).
Loosen the two hex screws (1/Fig. 6 / p. 16) and (1/Fig. 7 / p. 16) (approx. 2 turns).

Fig. 6: Wobbling screws Fully Automated Fig. 7: Wobbling screws Fully Synchronized
System System

2. Correction
In the longitudinal direction of the support arm:

RAD/FLUORO AXRF-000.842.01.01.02 Page 16 of 44 Siemens

05.09 CS PS AX R/F
Check and Adjustment 17

- Loosen the two Allen screws (2/Fig. 6 / p. 16) or (2/Fig. 7 / p. 16) and
(3/Fig. 6 / p. 16) or (3/Fig. 7 / p. 16) (approx. 2 turns).

NOTE As soon as the Allen screw (2/Fig. 6 / p. 16) or

(2/Fig. 7 / p. 16) is loose, wobbling changes as a result of the
unit's own weight!

- Make a correction in the longitudinal direction with the hex screw (2/Fig. 6 / p. 16) or
(2/Fig. 7 / p. 16). With it, the support arm/tube assembly can be lowered or raised.
- Hand-tighten the Allen screws (2/Fig. 6 / p. 16) or (2/Fig. 7 / p. 16) and
(3/Fig. 6 / p. 16) or (3/Fig. 7 / p. 16) and check alignment in the horizontal, trans-
verse as well as in the longitudinal directions.
In the transverse direction of the support arm to the right or left:
- Loosen the two Allen screws (3/Fig. 6 / p. 16) and (3/Fig. 7 / p. 16) (approx. 2 turns).
- Make a correction in the transverse direction with the hex screw (3/Fig. 6 / p. 16) or
(3/Fig. 7 / p. 16). With it, the support arm/tube assembly can be tilted to the left or
right.
- Hand-tighten the Allen screws (3/Fig. 6 / p. 16) and (3/Fig. 7 / p. 16) and check align-
ment in the horizontal, transverse as well as in the longitudinal directions.
3. If the result of the check is okay, hand-tighten the two hex screws (1/Fig. 6 / p. 16) and
(1/Fig. 7 / p. 16).
4. Tighten all Allen screws to 10 Nm and use Loctite 243.
5. Reinstall the cover panels.

NOTE After pivoting the tube unit support arm, alignment of the
tube unit must be checked in the transverse direction.

Tube Unit Drift 0

Fig. 8: Tube unit drift in the transverse direction

Siemens AXRF-000.842.01.01.02 Page 17 of 44 RAD/FLUORO

05.09 CS PS AX R/F
18 Check and Adjustment

Fig. 9: 3DV rotation axes

Pos. 1 RVA, Rotation around vertical axis
Pos. 2 RVA, Rotation around horizontal axis

Tube Unit Drift in the Transverse Direction

Tube unit drift must be checked in the transverse direction following
• replacement of the X-ray tube
• replacement or removal of the support arm
• Support Arm Wobble

Check

1. Position the 3D in the center of the room, between the two transverse and longitudinal
rails.
2. The check must be performed for the -90°, 0°, +90° and +180° support arm positions.

Fig. 10: Vertical tube unit rotation

3. Align the tube unit vertically to the floor; set it to the SID min. and switch on the light
localizer.
4. Mark the collimator centering cross on the floor.
5. Move the tube unit to the max. SID and observe the drift of the centering cross.

RAD/FLUORO AXRF-000.842.01.01.02 Page 18 of 44 Siemens

05.09 CS PS AX R/F
Check and Adjustment 19

6. The measured drift in the movement range may not exceed +/-10 mm.

¹ If the result is not within the tolerance, tube unit drift must be adjusted in the trans-
verse direction.

Adjustment

1. Remove the 4 half-cowl covers behind the TUI.

2. Loosen the set screws in the half-cowls on the support flange (Fig. 11 / p. 19) on the
right and left.

Fig. 11: Support flange set screws

3. Loosen the mounting screws for the control element mount (1/Fig. 12 / p. 19) on the
right and left.

Fig. 12: Control element mount mounting screws

Siemens AXRF-000.842.01.01.02 Page 19 of 44 RAD/FLUORO

05.09 CS PS AX R/F
20 Check and Adjustment

4. Loosen the two screws on the support flange half-cowls (Fig. 13 / p. 20).

Fig. 13: Tube unit support flange

5. The check must be performed for the -90°, 0°, +90° and +180° tube unit support arm
positions. It is possible that an average must be determined between the -90° and +90°
or 0° and +180° positions. Because of this, the drift in the individual positions must be
measured on the floor and a note made of them.
Align the tube unit and check the drift again.

Fig. 14: Vertical tube unit rotation

6. If the drift is within the tolerance, mark the centering cross on the floor, tighten the sup-
port flange screws. Here, make sure that the position does not change when tightening
the screws by observing the mark on the floor.
7. Retighten the set screws (Fig. 11 / p. 19).
8. Retighten the mounting screws for the control element mount (1/Fig. 12 / p. 19) on the
right and left.
9. Reinstall the cover panels.

RAD/FLUORO AXRF-000.842.01.01.02 Page 20 of 44 Siemens

05.09 CS PS AX R/F
Check and Adjustment 21

NOTE
After adjusting the tube unit in the transverse direction, the
RVA tube assembly drift (rotation around the vertical axis)
• must be checked for the Fully Synchronized system and,
if needed, must be mechanically adjusted.
• must be adjusted for the Fully Automated system in the
SSW system.

RVA, Rotation around Vertical Axis

Check
on the Bucky wall stand
1. Align the tube unit to the BWS and move to the min. SID. Switch on the light localizer.
2. Mark the light field on the BWS (collimator centering cross).
3. Move the tube unit to the max. SID.
4. The measured drift to the left or right in the working range may not exceed +/-3 mm.
¹ If the drift is not within the specified tolerance, the drift must be readjusted.

Adjustment
With the Ysio Fully Automated Systems, perform this adjustment in the SSW in the menu
Tune Up > Stand > Home Position Adjustment, all axles per the Online Help.
Adjustment of the vertical tube rotation must be performed mechanically for the Ysio Fully
Synchronized System:

1. Remove the cover panels on the rear of the support arm (Fig. 15 / p. 21) that cover the
column.

Fig. 15: Suspension of support arm Fully Synchronized System

Siemens AXRF-000.842.01.01.02 Page 21 of 44 RAD/FLUORO

05.09 CS PS AX R/F
22 Check and Adjustment

2. To adjust the stop disk for the vertical axis, loosen the (Fig. 16 / p. 22) securing screw
(1/Fig. 17 / p. 22).

Fig. 16: Adjusting the RVA stop disk

Fig. 17: RVA and RHA adjustment screws

Pos. 1 Securing screw (Allen screw)
Pos. 2 Eccentric bolt

3. Release the brake by pressing the appropriate button for vertical tube rotation on the
TUI.
The brake must be released during the adjustment.
4. For the adjustment, turn the eccentric bolt (2/Fig. 17 / p. 22).
5. Retighten the securing screw (1/Fig. 17 / p. 22).
6. Recheck the drift.
7. Reinstall the cover panels.

RVA, Rotation around Horizontal Axis

Check
on the Bucky wall stand
1. Align the tube unit to the BWS and move to the min. SID. Switch on the light localizer.
2. Mark the light field on the BWS (collimator centering cross).
3. Move the tube unit to the max. SID.
4. The measured drift up or down in the working range may not exceed +/-3 mm.
on the table
1. Align the tube unit to the table and move to the min. SID. Switch on the light localizer.
2. Mark the light field on the table (collimator centering cross).
3. Move the tube unit to the max. SID.
4. The measured drift to the left or right in the working range may not exceed +/-3 mm.

RAD/FLUORO AXRF-000.842.01.01.02 Page 22 of 44 Siemens

05.09 CS PS AX R/F
Check and Adjustment 23

¹ If the drift is not within the specified tolerance, the drift must be readjusted.

Adjustment
With the Ysio Fully Automated Systems, perform this adjustment in the SSW in the menu
Tune Up > Stand > Home Position Adjustment, all axles per the Online Help.
Adjustment of the horizontal tube rotation must be performed mechanically for the Ysio
Fully Synchronized System:

1. Remove the cover panels on the rear of the support arm (Fig. 18 / p. 23) that cover the
column.

Fig. 18: Suspension of support arm Fully Synchronized System

2. To adjust the stop disk for the horizontal axis, loosen the (Fig. 19 / p. 23) securing
screw (1/Fig. 20 / p. 23).

Fig. 19: Adjusting the RHA stop disk

Fig. 20: RVA and RHA adjustment screws

Pos. 1 Securing screw (Allen screw)
Pos. 2 Eccentric bolt

Siemens AXRF-000.842.01.01.02 Page 23 of 44 RAD/FLUORO

05.09 CS PS AX R/F
24 Check and Adjustment

3. Release the brake by pressing the appropriate button for horizontal tube rotation on the
TUI.
The brake must be released during the adjustment.
4. For the adjustment, turn the eccentric bolt (2/Fig. 20 / p. 23).
5. Retighten the securing screw (1/Fig. 20 / p. 23).
6. Recheck the drift.
7. Reinstall the cover panels.

Aligning the Collimator 0

Must be performed following

• replacement or removal of the collimator
• replacement or removal of the tube assembly.

Check

NOTE Before alignment of the collimator can be checked, it must be

ensured that the tube assembly drift RVA (rotation around the
vertical axis) is correctly adjusted!

1. Center the tube unit over the table.

2. Switch on the light localizer.
3. The light field must be parallel to the tabletop.
4. Select an appropriate organ program and release an exposure.
The collimator plates should be even horizontally and must be parallel in the image.

Adjustment
The adjustment can be found in the CB-DOC under Collimator > Adjustment
(AX74-020.842.01).

RAD/FLUORO AXRF-000.842.01.01.02 Page 24 of 44 Siemens

05.09 CS PS AX R/F
Check and Adjustment 25

Spring-loaded Mechanism 2.1

Adjusting the Weight Compensation 0

Must be performed after

• replacement or removal of the spring-loaded mechanism.
• a period of time when the spring force relaxes.

Check

1. Position the 3D in the upper area.

2. Press and hold the button on the TUI for the manual Up/Down movement direction
(Fig. 21 / p. 25).

Fig. 21: TUI

3. Apply even force down on the 3D with a spring balance.
Once the 3D has begun movement and moves at even speed, the force displayed on
the spring balance may be a max. of 35 N.
4. Position the 3D in the bottom area.
5. Press and hold the button on the TUI for the manual Up/Down movement direction
(Fig. 21 / p. 25).
6. Apply even force up on the 3D with a spring balance.
Once the 3D has begun movement and moves at even speed, the force displayed on
the spring balance may be a max. of 25 N.

Adjustment

1. If downward force during movement exceeds 35 N, the screw on the spring-loaded

mechanism for weight compensation (Fig. 22 / p. 26) must be turned counterclockwise.
2. If upward force during movement exceeds 25 N, the screw on the spring-loaded mech-
anism for weight compensation (Fig. 22 / p. 26) must be turned clockwise.
3. Perform a check of the adjustment again.

Siemens AXRF-000.842.01.01.02 Page 25 of 44 RAD/FLUORO

05.09 CS PS AX R/F
26 Check and Adjustment

Fig. 22: Spring-loaded mechanism

RAD/FLUORO AXRF-000.842.01.01.02 Page 26 of 44 Siemens

05.09 CS PS AX R/F
Check and Adjustment 27

Potentiometers 2.2

Adjustment of the Potentiometer for the transverse Axis (only Fully Synchronized
System) 0

Perform
• following replacement or removal of the potentiometer.
• if there are problems with the position display.

Adjust the potentiometer for position sensing of the transverse axis using the SSW.
1. Log in to the SSW.
Select the Tune Up > Stand > Position Check menu.
2. The check of the potentiometer range for the transverse axis is activated by selecting
Set. Position the 3D in the middle of the movement range of the transverse axis and
turn the potentiometer in the valid value range. When the value range has been
reached, the “Success“ audible signal sounds. If the 3D is outside of the valid value
range, the “Fail“ audible signal sounds (continuous signal).
3. The screen is exited by selecting Exit.

Siemens AXRF-000.842.01.01.02 Page 27 of 44 RAD/FLUORO

05.09 CS PS AX R/F
28 Check and Adjustment

Brakes 2.3

Vertical Axis Brake Gap (RVA) 0

NOTE The brakes are pre-adjusted and do not have to be adjusted.

Perform only with express instructions from the factory!

Two CSEs are required.

Check

1. Remove the cover panels on the rear of the support arm (Fig. 23 / p. 28) that cover the
column.

Fig. 23: Suspension of support arm Fully Automated System

2. Check the brake gap with the feeler gauge (Fig. 24 / p. 28). To do this, press the button
on the TUI for the vertical movement direction. The brake gap must be 0,3 + 0,1 mm.
The brake gap must be even all the way around.

Fig. 25: RVA bearing

Pos. 1 Brake gap
Fig. 24: Checking the RVA brake gap

RAD/FLUORO AXRF-000.842.01.01.02 Page 28 of 44 Siemens

05.09 CS PS AX R/F
Check and Adjustment 29

Adjustment

1. During the adjustment, press the button on the TUI for the vertical movement direction.
The screws to adjust the brake gap (1/Fig. 26 / p. 29) for the vertical axis are located on
the bottom of the tube unit support arm.
Loosen the Allen screws (1/Fig. 27 / p. 29) and adjust the brake gap with the adjust-
ment screws (hex screws) (2/Fig. 27 / p. 29).
The brake gap must be 0,3 + 0,1 mm all around.

Fig. 26: Adjusting the RVA brake gap

Fig. 27: Brake gap adjustment screws

Pos. 1 Securing screw (Allen screw)
Pos. 2 Adjustment screw (hex screw)

2. Tighten the securing screw (1/Fig. 27 / p. 29) with Loctite 243.

3. Check rotation:
- easy rotation
- no scraping
- easy release and application of the brake
4. Reinstall the cover panels.

Horizontal Axis Brake Gap (RHA) 0

NOTE The brakes are pre-adjusted and do not have to be adjusted.

Perform only with express instructions from the factory!

Two CSEs are required.

Siemens AXRF-000.842.01.01.02 Page 29 of 44 RAD/FLUORO

05.09 CS PS AX R/F
30 Check and Adjustment

Check

1. Remove the cover panels on the rear of the support arm (Fig. 28 / p. 30) that cover the
column.

Fig. 28: Suspension of support arm Fully Automated System

2. Check the brake gap with the feeler gauge (Fig. 29 / p. 30). To do this, press the button
on the TUI for the horizontal movement direction. The brake gap must be
0,35 + 0,1 mm.
The brake gap must be even all the way around. The brake gap is not easily accessi-
ble. Measurement can be only at points. The illustration shows an example of a point
measurement (Fig. 29 / p. 30).

Fig. 29: Checking the RHA brake gap

Fig. 30: RHA bearing
Pos. 1 Brake gap

RAD/FLUORO AXRF-000.842.01.01.02 Page 30 of 44 Siemens

05.09 CS PS AX R/F
Check and Adjustment 31

Adjustment

1. During the adjustment, press the button on the TUI for the movement direction.
The screws to adjust the brake gap for the horizontal axis (1/Fig. 31 / p. 31) and
(1/Fig. 32 / p. 31) are located on the back of the tube unit support arm.
Loosen the Allen screws (1/Fig. 33 / p. 31) and adjust the brake gap with the adjust-
ment screws (hex screws) (2/Fig. 33 / p. 31).
The brake gap must be 0,35 + 0,1 mm all around.

Fig. 31: Adjusting the Ysio F RHA brake gap

Fig. 33: Brake gap adjustment screws

Pos. 1 Securing screw (Allen screw)
Pos. 2 Adjustment screw (hex screw)

Fig. 32: Adjusting the Ysio S RHA brake gap

2. Tighten the securing screws (1/Fig. 33 / p. 31) with Loctite 243.

3. Check rotation:
- easy rotation
- no scraping
- easy release and application of the brake
4. Reinstall the cover panels.

Siemens AXRF-000.842.01.01.02 Page 31 of 44 RAD/FLUORO

05.09 CS PS AX R/F
32 Check and Adjustment

Transverse and Longitudinal Carriage Brake Gap (only Fully Synchronized Sys-
tem) 0

NOTE The brakes are pre-adjusted and do not have to be adjusted.

Perform only with express instructions from the factory!

Check
If the brake gap is too large because the pads are worn, a noise (clattering) will develop
when the brakes are applied.
Check the brake gap with a feeler gauge ((Fig. 34 / p. 32) or (Fig. 35 / p. 32)).
Brake pad surface to the surface: 0,05 + 0,1 mm

Fig. 34: Checking the longitudinal direction brake Fig. 35: Checking the transverse direction brake
gap gap

Adjustment

1. Loosen the set screws (Fig. 37 / p. 33).

2. Adjust the brake gap with the two eccentric bolts (Fig. 36 / p. 33).

NOTE The surface of the eccentric bolts must be flush with the
mounting bracket. Only turn the eccentric bolts, do NOT
press them!

3. Retighten the set screws (Fig. 37 / p. 33).

RAD/FLUORO AXRF-000.842.01.01.02 Page 32 of 44 Siemens

05.09 CS PS AX R/F
Check and Adjustment 33

Fig. 36: Brake assembly eccentric bolt Fig. 37: Brake assembly set screw

Siemens AXRF-000.842.01.01.02 Page 33 of 44 RAD/FLUORO

05.09 CS PS AX R/F
34 Check and Adjustment

Detent Forces (only Fully Synchronized System) 2.4

The detent forces for the horizontal and vertical axis rotation may have to be adjusted per
the customer's request.

1. Remove the cover panels on the rear of the support arm (Fig. 38 / p. 34) that cover the
column.

Fig. 38: Suspension of support arm Fully Synchronized System

2. The detent forces must be adjusted at the particular Allen screw for the horizontal and
vertical axis (Fig. 39 / p. 34).

Fig. 39: Adjusting the RVA and RHA detent forces

Pos. 1 RHA detent force adjustment screws
Pos. 2 RVA detent force adjustment screw

RAD/FLUORO AXRF-000.842.01.01.02 Page 34 of 44 Siemens

05.09 CS PS AX R/F
Check and Adjustment 35

3. If only turning the screw for the vertical axis is not sufficient to adjust the detent force,
washers can be placed under the springs. Spare washers are located in the support
arm (Fig. 40 / p. 35).

Fig. 40: Fully Synchronized System support arm spare washers

4. Reinstall the cover panels.

Siemens AXRF-000.842.01.01.02 Page 35 of 44 RAD/FLUORO

05.09 CS PS AX R/F
36 Check and Adjustment

Stop Assembly (only Fully Synchronized System) 2.5

NOTE The detent assembly is pre-adjusted and does not have to be

adjusted.
In a malfunction situation, corrections can be made.

Fig. 41: Y311 and Y312 stop assembly, drawing

Pos. 1 S1 sensor
Pos. 2 S2 sensor
Pos. 3 S3 sensor

Procedure of the Y311 stop assembly in the longitudinal direction:

• Light on the S2 sensor on: Sensor is in the stop detent ramp (1/Fig. 42 / p. 37).
• Light on S1 and S2 sensors on: Sensor is over the stop detent (2/Fig. 42 / p. 37).
• Light on the S3 sensor on: the stud is engaged.

Procedure of the Y312 stop assembly in the transverse direction:

• Light on the S1 sensor on: Sensor is in the stop detent ramp (1/Fig. 42 / p. 37).
• Light on S1 and S2 sensors on: Sensor is over the stop detent (2/Fig. 42 / p. 37).
• Light on the S3 sensor on: the stud is engaged.

RAD/FLUORO AXRF-000.842.01.01.02 Page 36 of 44 Siemens

05.09 CS PS AX R/F
Check and Adjustment 37

Fig. 42: Stop assembly

If the sensor does not react, it is possible to adjust the sensor by moving it.
1. The spacing of S1 and S2 to the metal bracket for the stop assembly (1/Fig. 43 / p. 38)
is 3 ± 0.3 mm.
2. The spacing of S3 to the plate while switched on (stud is engaged, magnet is powered)
(2/Fig. 43 / p. 38) is 2 ± 0.3 mm.
3. The counter nut (3/Fig. 43 / p. 38) must be tightened! The plate can be moved!

Siemens AXRF-000.842.01.01.02 Page 37 of 44 RAD/FLUORO

05.09 CS PS AX R/F
38 Check and Adjustment

Fig. 43: Adjusting the Y311 an Y312 stop assemblies

Pos. 1 Spacing of S1/S2 to the metal bracket
Pos. 2 Spacing of S3 to the plate when switched on
Pos. 3 Counter nut

RAD/FLUORO AXRF-000.842.01.01.02 Page 38 of 44 Siemens

05.09 CS PS AX R/F
Final Work Steps 39
3-
Adjusting in the SSW
3Final Work Steps

If the drift of the central beam is adjusted, the adjustments in the SSW must then be per-
formed again.

1. Home Position Adjustment, all axles

2. End Position Adjustment
3. Checking the Detents (only Fully Synchronized System)
4. Centering
Performance of the adjustments in the SSW can be found from the current Online Help per
the SSW.

Siemens AXRF-000.842.01.01.02 Page 39 of 44 RAD/FLUORO

05.09 CS PS AX R/F
40 Final Work Steps

Checking Central Beam Drift 3.1

Table 0

1. Select a suitable organ program and center the tube unit over the table.
2. Switch on the light localizer.
3. Position the ball phantom to the centering cross of the light field on the table
4. Release an exposure.
5. The ball in the image must appear inside the circle (Fig. 44 / p. 40).

Fig. 44: Exposure with the ball phantom

Bucky Wall Stand 0

Detector in the vertical Position

1. Move the detector into the vertical position.
2. Select a suitable organ program and center the tube unit to the Bucky wall stand.
3. Switch on the light localizer.
4. Attach the ball phantom exactly on the centering cross of the light field on the front
panel.
5. Release an exposure.
6. The ball in the image must appear inside the circle (Fig. 44 / p. 40).

Detector in the horizontal Position

1. Move the detector into the horizontal position.
2. Select a suitable organ program and center the tube unit to the Bucky wall stand.
3. Switch on the light localizer.

RAD/FLUORO AXRF-000.842.01.01.02 Page 40 of 44 Siemens

05.09 CS PS AX R/F
Final Work Steps 41

4. Position the ball phantom to the centering cross of the light field on the front panel.
5. Release an exposure.
6. The ball in the image must appear inside the circle (Fig. 44 / p. 40).

Siemens AXRF-000.842.01.01.02 Page 41 of 44 RAD/FLUORO

05.09 CS PS AX R/F
42 Final Work Steps

IQAP 3.2

A change in the adjustment of the radiation field must be checked with IQAP and docu-
mented.
For this, start a Partial Test and perform the ColliCenter test point. If an adjustment of the
light/radiation field was performed or if the collimator was removed from the tube unit, per-
form the test point Light and XRay.

NOTE The country-specific regulations must be observed and, if

applicable, perform the country-specific acceptance tests!

RAD/FLUORO AXRF-000.842.01.01.02 Page 42 of 44 Siemens

05.09 CS PS AX R/F
Changes to Previous Version 43
4Changes to Previous Version 4-

Chapter Changes
n.a. n.a.

Siemens AXRF-000.842.01.01.02 Page 43 of 44 RAD/FLUORO

05.09 CS PS AX R/F
44 Index

A
5Index

Aids and Tools. . . . . . . . . . . . . . . . . . . . 4

G General Remarks . . . . . . . . . . . . . . . . . 5

RAD/FLUORO AXRF-000.842.01.01.02 Page 44 of 44 Siemens

05.09 CS PS AX R/F