NIF: B86101110 CALLE ARTURO BALDASANO 26 1D 28043 MADRID ESPAÑA

Telf. 00 34 692990962 / 00 34 915946952

Oferta

No. 02-07072015
Fecha 07/07/2015
Atn: Ing. Cesar Villorin /Inmaserca

Email: cesar [email protected]

Descripción Cantidad Precio Unitario $ Precio Total $

Soft Starter STAT 600S4K16A1000 1 $196.419 $196.419

for for motors 3750hp-4.16KV
The soft starter is including mainly: By pass contactor, and output ground switch.
Annex I: Soft starter with included options
Annex II: Documentation
Puesta en marcha
1 $2.000 $2.000
Gastos de viaje (costo +15%)

This budgetary offer could be confirmed and accepted only after the calculation of the
technical feasibility of the starting of soft starter with the motor and the load.
To make these starting calculations we need:
For the load:
- The starting load torque curve VS speed
- The inertia of the load
For the motor:
- The complete Motor Data sheet
- The starting current curve of the motor VS motor speed
- The starting torque curve of the motor VS motor speed
- The Inertia of the motor

CONDICIONES:

Precio: Ex-Works Roche-La-Molière FRANCE

Disponibilidad : 16 a 20 semanas

Cotizacion Valida : 30 días

Condiciones de pago
120 días
:

Garantia : 12 meses despues de la puesta en marcha y 18 meses despues de la entrega

1
ANNEX I

2
 ANNEX II

IP32 Enclosure, dimensions (mm): W-1200, H-2420, D-1200 Standard colour RAL 7035
The single cabinet has 2 fully segregated compartments The MV compartment
The LV compartment
In the MV compartment:
STAT Power section with thyristors firing circuits.
Soft starter current rating will be according to motor’s starting current and starting time, while the voltage will be according to mains
voltage.
See included presentation for available voltage and current products.
By pass contactor or circuit breaker operating voltage and current will be according to motor’s voltage and current.
Power connection between soft starter and contactors can be by bus bars or cables according to contactor type and application
constraints as for example Marine ambiance.
In the LV compartment:
Each soft starter has a separated front accessible low voltage Compartment with the following components mounted on the door: Push buttons:
Emergency stop (mushroom type)
Lamp test Reset Fault
Direct on line selector (option)
Signal lights: Soft starter bypassed (green)
General Fault (red)
Auxiliary voltage alive (white) Bus bar alive
Direct on line mode (option)
Others in accordance with the selected options.

3
Option: Line cabinet
Line requested options could be installed in additional line cabinet:
- Line contactor
- Line switch + Input ground switch
- MV Fuses
- Motor protection relay including the following protections:
- overcurrent : code ANSI 50/51
- ground fault : code ANSI 50N/51N
- Circuit breaker fault code ANSI 50NBF
- Unbalance and inverse phase code ANSI 46
- Directional ground fault code ANSI 67N/67NC
- Maxi active power code ANSI 32P
- Maxi reactive power code ANSI 32Q
- Overload code ANSI 49RMS
- Current loss code ANSI 37
- Stalled rotor: code ANSI 48/51LR
- Starting number / operation hours code ANSI 66
- Under voltage code ANSI 27D/27R
- Over voltage code ANSI 59N
- Inverse voltage code ANSI 47
- Maxi frequency code ANSI 81H
- Mini frequency code ANSI 81L

Design :
The soft starter starts the motor by slowly ramping-up the voltage supplied to the motor while limiting the current at the requested level.
The soft starter control is based on a digital microprocessor system.
The signal interconnections to the power section are based on a high speed fiber optic link that gives a high degree of insulation and EMC immunity.
Voltage rating: · 3,3 KV – 4,16 KV – 5,5 KV – 6,6 KV- 10 KV - 11 KV +- 10%
Frequency: 50/60 Hz +- 5%
Continuous current rating: 80A – 160A – 260A – 350A – 450A – 600A – 900A -1200A Current limit: adjustment 100 – 300% In of the soft starter
Soft starter installation: TN
Operating temperature range, industrial version: 0 to 40°C Operating temperature range, Marine version: 0 to 45°C Maximum relative humidity: up to 96 %
(non condensing) Maximum altitude: 1107 m.
Storage temperature: -20 to 70°C
Number of starts: 3 per hour at maximum conditions Auxiliary Voltage:
120 Vac / 200 VA from dedicated Power Transformer 240 Vac by UPS / 1500 VA
240 Vac / 1500 VA

4
Control and Keypad :
Remote control with dedicated digital inputs Remote monitoring with dedicated digital outputs Profibus communication as option:
Parameter setting Control (Start,Stop,…) Supervision
LCD display with programming keypad and status LED.
The LCD displays motor current, firing angle of thyristors, fault description. The LED 7 segments is used for quick status display
It shows the basic diagnostics information about the Power-up and
Reset tests, about the eventual intervention of the protections and the operating state of the soft starter.
SOFT STARTER PROTECTIONS:
Line loss.
Serial communication failure.
External protection.
Motor thermal protection
Max instantaneous current.
Soft starter thermal protection
Watchdog intervention.
Motor stall
Line beyond tolerance
SOFT STARTER IN CABINET STANDARDS :
IEC 62271-200 -- High voltage switchgear: AC metal enclosed switchgear and control gear for rated voltages above 1kV and up to and including 52kV

IEC 60060-1 / 2 -- High voltage tests techniques: Measuring systems

IEC 60071-1/ 2 -- Insulation coordination: Definitions, principles and rules / Application guide IEC 61800-5-1 -- Adjustable speed electrical power drive
system: Safety requirements: electrical, thermal and energy
IEC 61800-3 -- Adjustable speed electrical power drive system: EMC requirements and specific test methods
IEC 61800-4 -- Adjustable speed electrical power drive system: rating specification for A.C Power drive systems above 1000 Vac and not exceeding 35
KVac.
IEC 60694 -- Common specifications for high voltage switchgear & control gear standards CEI EN 50178 -- Electronic equipment for use in power
installation
IEC 60947-2 -- Specification for low voltage switchgear and control gear: circuit breakers IEC 60470 -- High voltage alternating current contactors and
contactor based motor starter IEC 60282 -- High/Medium voltage fuses
EN 60269 -- Low Voltage fuses IEC 754 -- Medium voltage cables
Marine As option the Marine Certifications (ABS,….)