ARC5305 Long-Span & Special Structures

Chapter Four

Tensile Structures

25-Mar-24 Tensile Structures 1

 Outlines
Introduction

Conceptual Development

Types of Tensile Structures

Components of Tensile Structures

25-Mar-24 Tensile Structures 2

 Introduction
In practice, structures tend to carry
both tension and compression and it is the degree to
which a structure is intentionally tensioned to stabilize
it that determines whether it is considered a tensile
structure.
Tensioning is usually achieved with wire or cable
opposed by compression elements such as masts and
held in place by foundations, ring beams, ground
anchors and so on.

25-Mar-24 Tensile Structures 3

 Introduction
Tensioning can also be achieved through inflation
(pneumatic structures).
Tensile structure is the term refers to the
construction of roofs using a membrane held in
place on steel cables.
A tensile membrane structure is most often used as
a roof as they can economically and attractively
span large distances.
25-Mar-24 Tensile Structures 4
 Introduction
These types of structures are commonly found in
sports facilities, warehousing, storage buildings
and exhibition venues.

Examples of tension structures are Fabrics

structures, Cable net structures, Suspension
bridges, Cable-stayed bridges, pneumatic
structures and pre-stressed cable nets and beams.

25-Mar-24 Tensile Structures 5

 Introduction
The term tensile structures also describes the
category of buildings in which the load bearing
capacity is achieved through tension stress in the
majority of the components such as technical
fabrics (Fabrics structures) or foils.

25-Mar-24 Tensile Structures 6

 Introduction

25-Mar-24 Tensile Structures 7

 Introduction

Golden gate suspension bridge, San Fransisco, USA

25-Mar-24 Tensile Structures 8

 Introduction

Denver station, Colorado, USA

25-Mar-24 Tensile Structures 9

 Introduction
Millennium Dome, London

25-Mar-24 Tensile Structures 10

 Introduction

Supports

25-Mar-24 Tensile Structures 11

 Introduction

Inside view

25-Mar-24 Tensile Structures 12

 Conceptual Development
The use of material is inefficient in bending
elements.
The interior fibers never reach their maximum
stress levels while always maintaining weight.
From this idea, the truss was developed where the
inefficient material of the beam was turned into
clear space and each truss carried specific tension
and compression forces.
25-Mar-24 Tensile Structures 13
 Conceptual Development
However, the most simplest efficient structural
system is when load is carried by one element that is
either completely in tension or compression.

While in 2D, this system is a cable for tension

loads and an arch for compression loads, in 3D
space, this system is a dome and tensioned fabric
respectively.

25-Mar-24 Tensile Structures 14

 Conceptual Development

25-Mar-24 Tensile Structures 15

 Conceptual Development
Therefore, terms membrane structure and
tensioned fabric structure not only allude to the
nature of the material used in such design but also
the way in which the forces act within the system.

The stresses created are membrane stresses that is,

stresses acting parallel to the local surface and
constant through the thickness of the surface.

25-Mar-24 Tensile Structures 16

 Conceptual Development
However, when the membrane is loaded since it
can not carry any out of plane stresses, it deforms
until all the surface forces find a new equilibrium.
Pre-tensioning of the membrane is necessary to
decrease potential deflection.
On a loaded pre-tensioned membrane, the final
deflection will be less than a non-tensioned
membrane.
25-Mar-24 Tensile Structures 17
 Conceptual Development
However, at the same time the final tension will be
higher.
The primary structure which is usually made up of
compression elements play an important role for it
equalizes and maintains forces from the pre-stressing
of the fabric.
Not only do they transmit the loads to the ground, but
the supporting structure ultimately controls the
geometric parameters of the structure.

25-Mar-24 Tensile Structures 18

 Types of Tensile Structures
The classification of tensile structures are made
based on:

 the plane in which the tensile forces are acting in

the structure

 Shapes

 the type of supports provided

25-Mar-24 Tensile Structures 19

 Types of Tensile Structures
Classification of tensile structures based on the
plane in which the tensile forces are acting

On this basis, the tensile structure are divided into

following types.

a) Linear Tensile Structures

b) Three-dimensional Tensile Structures

c) Surface-Stressed Tensile Structures

25-Mar-24 Tensile Structures 20

 Types of Tensile Structures
a) Linear Tensile Structures

All the member are in linear tensile forces and

supported by the compression members.

The major loads are carried out by tensile members

(cables).

Example:- Suspension bridges, Cable-stayed

bridges, Cable-stayed beams or trusses

25-Mar-24 Tensile Structures 21

 Types of Tensile Structures
Main pillars acts as compression members but the
whole load is carried out by the cables which are
in tension.

25-Mar-24 Tensile Structures 22

 Types of Tensile Structures

Cable-stayed bridges

25-Mar-24 Tensile Structures 23

 Types of Tensile Structures
b) Three-dimensional Tensile Structures

a compilation of elements that are primarily in

tension with the compression being transferred to a
central mast and down into the ground.

The most common occurrence of three-dimensional

tension can be seen at sports arenas and usually
serve as roofs for these structures.

25-Mar-24 Tensile Structures 24

 Types of Tensile Structures
c) Surface-Stressed Tensile Structures
The surface members are tension bearing members.
Fabric tensile structures are the great examples
of Surface-stressed tensile structures.
The vertical pillars hold the special designed fabric
which is in tension.
Examples:- Fabric structure, Pre-stressed membranes,
Pneumatically stressed membranes, Grid shell

25-Mar-24 Tensile Structures 25

 Types of Tensile Structures

25-Mar-24 Tensile Structures 26

 Types of Tensile Structures
Classification of tensile structures based on the
shapes

a) Conical Tension Structure

b) Hyperbolic paraboloid or Anticlastic Structure

c) Parallel Arch or Barrel Vault Structure

d) Cable Net and Membrane Structure

25-Mar-24 Tensile Structures 27

 Types of Tensile Structures
a) Conical Tension Structure

Membranes are tensioned between a ring at the

pinnacle and the lower perimeter support columns.

Highly effective for covering large areas.

Cones are especially effective in areas that need to

comply with high rain or snow load regulations.

Easily identified by its tent-like shape.

25-Mar-24 Tensile Structures 28

 Types of Tensile Structures

Denver International Airport, USA

25-Mar-24 Tensile Structures 29

 Types of Tensile Structures

Inside view

25-Mar-24 Tensile Structures 30

 Types of Tensile Structures

25-Mar-24 Tensile Structures 31

 Types of Tensile Structures
b) Hyperbolic paraboloid or Anticlastic Structure
These structures rely on two opposing curvatures also
known as anticlastic for their stability.
Anticlastic surfaces have negative Gaussian curvature.
This means the two directional forces are in opposing
directions such as the cone, saddle or hyperbolic
paraboloid.
This type of structure is ideal for shade over seating
areas or high traffic walkways.
25-Mar-24 Tensile Structures 32
 Types of Tensile Structures
The opposing directional forces that are introduced
by pre-stressing the fabric in both directions
counterbalance each other.
Conversely, synclastic surfaces have positive
Gaussian curvature that is curvature in the same
direction such the dome.
Since the forces are in the same orientation, these
forces must be balanced by air pressure.
25-Mar-24 Tensile Structures 33
 Types of Tensile Structures

25-Mar-24 Tensile Structures 34

 Types of Tensile Structures

25-Mar-24 Tensile Structures 35

 Types of Tensile Structures

25-Mar-24 Tensile Structures 36

 Types of Tensile Structures
c) Parallel Arch or Barrel Vault Structure

It’s a symmetrical curved parallel arch.

Incredibly functional tensioned membrane canopy

Span long distances such as a sports arena or

smaller areas such as an entryway.

25-Mar-24 Tensile Structures 37

 Types of Tensile Structures

25-Mar-24 Tensile Structures 38

 Types of Tensile Structures
d) Cable Net and Membrane Structure

For long-span tensile membrane roofing

applications typically found in stadiums or large
spaces.

3D cable net or cable grid structures are an efficient

solution for lightweight tensile architecture.

25-Mar-24 Tensile Structures 39

 Types of Tensile Structures
Classification of tensile structures based on the type
of supports provided

a) Stayed

b) Suspended

c) Anticlastic

d) Pneumatic

e) Cable truss
25-Mar-24 Tensile Structures 40
 Types of Tensile Structures
a) Stayed Tensile Structures

25-Mar-24 Tensile Structures 41

 Types of Tensile Structures

25-Mar-24 Tensile Structures 42

 Types of Tensile Structures
b) Suspended Structure

25-Mar-24 Tensile Structures 43

 Types of Tensile Structures
The sequence of force transmission for the
suspension bridge:

Vehicular load + Dead load → to the deck → to the

suspender → to the main cable → to the bridge tower
→ the last to foundation.

25-Mar-24 Tensile Structures 44

 Types of Tensile Structures

25-Mar-24 Tensile Structures 45

 Types of Tensile Structures
c) Anticlastic structure

Structure with two different curvatures acting in

opposite direction.

25-Mar-24 Tensile Structures 46

 Types of Tensile Structures

25-Mar-24 Tensile Structures 47

 Types of Tensile Structures
d) Pneumatic Structure

 Pneumatic structure is a membrane structure stabilized by the

pressure of compressed air.

 Air-supported structures are supported by internal air pressure.

 A network of cables stiffens the fabric and the assembly is

supported by a rigid ring at the edge.

 The components of a pneumatic structure consist of a membrane,

supporting cables and anchorage system and an HVAC system.

25-Mar-24 Tensile Structures 48

 Types of Tensile Structures

25-Mar-24 Tensile Structures 49

 Types of Tensile Structures

25-Mar-24 Tensile Structures 50

 Types of Tensile Structures
e) Cable truss Structure

25-Mar-24 Tensile Structures 51

 Types of Tensile Structures
e) Cable truss Structure

25-Mar-24 Tensile Structures 52

 Components of Tensile Structures
Structurally, the system is formalized by combining
three elements: membranes, rigid structures such
as pole and masts and cables.

Membranes are the elements which carries stresses

acting parallel to the local surface and may be
composed from PVC-coated polyester fibers or
PTFE-coated glass fiber.

25-Mar-24 Tensile Structures 53

 Components of Tensile Structures
Forms the enclosure of the structure. Connections
can be glued or heat welded.

25-Mar-24 Tensile Structures 54

 Components of Tensile Structures
The steel frame rigid structural elements such as
arches are to support the flexible fabric and cable
membrane generate its peaks form its edges.
• MAST SUPPORTED

25-Mar-24 Tensile Structures 55

 Components of Tensile Structures
Cables serve a number of functions in tensile
structure applications:

 Reinforcement of the fabric where the spans and

• MAST SUPPORTED
stresses get too large;

 Linear tension support elements along edges;

 Tie-backs and stays to stabilize rigid support

element.

25-Mar-24 Tensile Structures 56

 Components of Tensile Structures

• MAST SUPPORTED

25-Mar-24 Tensile Structures 57

 Components of Tensile Structures
Benefits of Tension Fabric Structures
 Beautifully diffused Daylighting
 Flexible design Aesthetics
 Long standing durability and sustainable
 Lightweight in nature
 Minimal maintenance
 Cost efficient
 Ability to span long distances
25-Mar-24 Tensile Structures 58
 Components of Tensile Structures
Disadvantages of Tension Fabric Structures

 Less fire resistance

 Acoustics
• MAST SUPPORTED

 Insulation

25-Mar-24 Tensile Structures 59