Original operating manual - GB -

High pressure cleaner

K 1050 P

Read and conform safety instructions before use!

Keep instructions in a safe place for later use and
pass them on to any future user.

www.kraenzle.com
 Technical data

Dear customer:
We would like to congratulate you on the purchase of your new high pressure
cleaner and thank you for your confidence in our products!
Your choice has fallen on an absolute quality product!
Kränzle high pressure cleaners are characterized by their convenient and
compact design as well as their high suitability for everyday use.
Highest precision and dimensional accuracy in addition to a technology
package consisting of a multitude of details mark the difference when it comes
to performance, safety and durability.
In order to facilitate handling of the K 1050 P the following pages are intended
to further explain its use.

Technical data K 1050 P

Operating pressure 130 bar (13 MPa)
Nozzle size 25 030
Permissible overpressure 160 bar (16 MPa)
Water output* 7.5 l/min (450 l/h)
Max. Wasserzulaufdruck 1.0 MPa
Water inlet temperatur (1-10 bar) max. 60 °C
High pressure hose 8m
Conected load 230V , 9.6 A , 50 Hz
Power input P1: 2.2 kW
Power outpu P2: 1.65 kW
Weight 19 kg
Dimensions in mm 390 x 290 x 370
Sound level acc. to DIN 45 635 75 dB (A)
Acoustic power LWA 86 dB (A)
Recoil at lance ca. 27 N
Vibration at lance 1.9 m/s2
Art. No. 49.501

* Must be supplied to the unit at least.

Permissible tolerance for figures ± 5 % acc. to VDMA uniform sheet 24411

2
Contents

Technical data ........................................................................ 2

Contents ................................................................................. 3

Description of high pressure cleaner ....................................... 4

Explanatory symbols .............................................................. 6

General rules .......................................................................... 7

Safety precautions .................................................................. 8

Functional details ................................................................... 11

Putting into operation ............................................................15

To shut down the pump ......................................................... 19

Small repairs - do it yourself! .................................................20

EC declaration of conformity ..................................................24

Wiring diagram ...................................................................... 25

Warranty ................................................................................26

Notes ..................................................................................... 27

Spare parts list .......................................................................28

3
 Description of high pressure cleaner

Design
The K 1050 P high pressure cleaner is a portable machine with an advanced
arrangement system. Please see construction scheme for more details.

1 Ergonomically shaped handle

1

2 Pump head made of brass

4
3 Start/Stop switch with pressure
5 3
2 relief for HP hoses

4 Power supply cable with plug

6

9 5 Pump outleet

7 6 Water connection supply with filter

8

11 10 7 Lances inside holder

6

8 On/Off switch

9 Cable reel

10 Trigger gun with safety catch

12 11 Gun holder

12 HP hose

4
 Description of high pressure cleaner

This is what you have purchased

1. Kränzle high pressure cleaner

K 1050 P

2. Trigger gun with safety catch with

insulated handle and plug coupling

3. Flat jet nozzle with stainless steel

pipe and plug-in nipple
Original-Betriebsanleitung -D-

Hochdruckreiniger

K 1050 P

4. Operating manual
Vor Inbetriebnahme Sicherheitshinweise
lesen und beachten!
Für späteren Gebrauch oder Nachbesitzer

5. Water connection supply, plug

coupling with visible filter

6. High pressure hose

Optional:
Art.No.: 42.403-03
Dirtkiller lance with stainless steel
pipe and plug-in nipple

5
 Explanatory symbols

Explanatory symbols used in the operating manual

Failure to observe this note may entail environmental

damage.

Note on the use of the machine that failure to adhere to the

instructions may cause excessive wear or total breakdown of the
K 1050 P.

Warning!
Failure to observe this note may result in serious injuries!

Explanatory symbols affixed to the high pressure cleaner

In case of improper use, the high pressure jet can be very

dangerous. Do not direct jet at persons, animals or active
electrical equipment or the machine itself.

The unit may not be connected directly to the public

drinking water supply network.

6
General rules

Range of application
Use machines for cleaning tasks with high pressure water jet and detergents or with
high pressure water jet without detergents only.
The high pressure cleaner is designed for use in private environment only.

Environmental, refuse disposal and water protection regulations

must be observed!

Inspections
The machine must be inspected according to the “Guidelines for Liquid Spray
Devices” at least once every 12 months by a qualified person, to ensure that
continued safe operation is guaranteed. The results of the inspection are to be
recorded in writing. This may be done in any form.

High pressure cleaners used for commercial purposes have to be

checked by a qualified person at least every 12 months!

Accident prevention
The machine is designed for accidents to be impossible if used correctly. The
operator is to be notified of the risk of injury from hot machine parts and the
high pressure water jet. The “Guidelines for Liquid Spray Devices” must be
complied with.

Oil leakage
If oil leaks contact your nearest after-sales service (dealer) at once.
Failure to observe this instruction may cause damage to the environment
and/or transmission gearbox.

7
 Safety precautions

Persons operating the machine should wear the necessary protective clothing,
i.e. waterproof clothing, rubber boots, safety goggles, headwear etc. It is prohibited
to use the machine in close vicinity to people lacking suitable protective clothing!

Do not spray against matter containing asbestos or other hazardous substances!

Never spray liquids containing solvents like varnish solvents, petrol, oil or
similar liquid!

Due to the high pressure jet, damage may occur on the objects to be cleaned,
e.g. car tires; therefore, a minimum distance of 30 cm is to be kept.

Prior to putting the high pressure cleaners into operation, check its components
(HP hose, power supply cables, safety trigger gun) for any damage. Replace defect
or damaged components!

The high pressure cleaner is to be properly used. The user is required to adhere
to local requirements and to watch out for any persons in the danger zone!

When using high pressure water for

cleaning, make sure that there is a clearly
noticeable recoil effect on the lance.
Therefore ensure a firm footing
(see chapter „Technical data“)

Apply the safety catch on the spray gun

after each use in order to prevent
unintentional spraying!

8
Safety notes - This is prohibited!

Never allow children or untrained persons

to use the high pressure cleaner!

Never direct the water jet at the machine

itself!

The machine may not be placed within

reach of the water jet spray mist!

Never direct the water jet at power sockets

or any other electrical installations!

Within the working area, all live parts are

to be protected from both water jet and
spray mist.

9
 Safety notes - This is prohibited!

Never direct the water jet at people or

animals!

Never direct the high pressure jet at

yourself or other persons, not even to
clean clothing or shoes.

Only use power cables which are in perfect

working order!

Do not damage or improperly repair cables

(tearing, squeezing, running over,…).

Never pull the high pressure hose if it has

formed kinks or “nooses”!

Never pull the hose over sharp edges!

10
Functional details

Please note - important: Lack of water

Lack of water occurs more often than you

probably believe. The more powerful a
high-cleaner is the greater is the danger
that a lack of water occurs. If there is only
an insufficient amount of water available,
cavitation (water-gas mixture) arises inside
the pump, which is normally noticed too
late or even not at all. The pump will be
destroyed. Please check the available
quantity of water by filling a bucket with
liter scale for one minute.

A minimum water quantity of 7.5 l/min is needed for the high pressure cleaner
to operate.

If the metered quantity of water is too small, you have to use a different
water connection, guaranteeing the necessary output.
Lack of water leads to an accelerated wear of the joints (guarantee void).

Never let the pump run dry for more than 20 seconds.

Water supply
Please pay attention to the regulations of your waterworks company!
In accordance with DIN EN 61770, the machine may not be directly
connected to the public drinking water supply lines. A brief connection
however is permissible according to DVGW (German Association
for Gas and Water Affairs) if a non-return valve with tube ventilator
(Kränzle order no. 41.016 4) is built into the water supply. Once the
water has passed through the non-return valve it is no longer
considered as drinking water. Also indirect connection to the
public drinking water supply lines is permissible by way of free
emission in accordance with EN 61 770; e.g. by using a reservoir
with a float valve. Direct connection to a non-drinking water
supply line is permissible.

11
 Functional details

Insufficient quantity of electricity

If there are too many collectors in your
proximity connected to the network at the
same time, the available voltage and the
current intensity may decline. Consequently
the motor of the high pressure cleaner does
not start or even blows. The power supply
may also be insufficient if the power cable is
too long or too thin.
If extension cables are too long, this may
lead to a voltage drop causing malfunctions
or start-up difficulties.
Kränzle 1050 P: 230 Volt / 50 Hz

Check the line fusing and have the voltage and the available current
intensity checked by an expert in case of uncertainty.

Electrical connection
The machine is supplied with a 5 meter electrical power cable with plug. The mains
plug must be fitted to a standard grounded socket with a 30 mA residual current
operated device. The socket must be protected with a 16 A fuse on the mains side.
When using an extension cable, this must have an earthed lead which is properly
connected to the socket. The conductors in the extension cable must have a
minimum cross section of 1.5 mm². Plug connections must be of a spray-proof design,
and may not be located on a wet floor. When using a cable drum, always keep the
cable wound as far as possible.

12
Functional details

Water and cleaning / care products system

Water can be connected at mains pressure to the high pressure pump. The water is
then forced under pressure by the high pressure pump to the lance. The high pressure
jet is formed by the nozzle at the end of the lance.

Environmental, refuse disposal and water protection regulations must

be observed!

Lance with trigger gun with safety catch

The machine can only be operated when the trigger of the trigger gun with safety
catch is pulled. When the trigger is pulled, the trigger gun opens. The liquid is then
pumped to the nozzle. The spray pressure increases and quickly reaches the selected
operating pressure. When the trigger is released, the trigger gun closes and any
further spraying of liquid from the lance is stopped. The pressure thrust serves to close
the start/stop system, thus causing interruption of the energy supply to the motor.
Owing to this innovative system the high pressure hose is relieved and enables higher
durability of the hose. Opening the gun causes the start/stop system to open, the
electric motor is automatically restarted and the pump starts to transfer the water
on to the high pressure jet where the cleaning jet is generated.

The trigger gun with safety catch is a safety device. Repairs should
only be performed by qualified persons. Should replacement parts be
required, use only components authorized by the manufacturer.

Replacements, repairs, new adjustments and sealing should only be

performed by qualified persons.

Prior to putting the machine into operation make sure that all safety
instructions be observed.

13
 Functional details

Motor overload protection

The motor is protected against overloading by means of an overload protection de-
vice included in the motor coil. In the event of overloading or jamming, the excess
temperature cut-out serves to switch off the motor. In case of repeated switching
off the motor by means of the excess temperature cut-out, make sure to eliminate
the cause of the failure.

Replacements and inspection work should only be performed by qualified

persons when the machine is disconnected from the power supply, i.e.
with plug pulled out from the electrical socket.

High pressure hose and spray device

The high pressure hose and spray device which are part of the K 1050 P equipment,
are made of high quality material and engineered to conform with the operating
conditions of the high pressure cleaner and are duly labeled.

If replacement parts are required, only such parts that are authorized
by the manufacturer may be used. The warranty is automatically void if
spare parts of third-party providers are used! The high pressure hose and
spray device must be connected in a pressure-tight manner
(without leakage).

The high pressure hose may not be driven over, pulled excessively, or twisted.
The hose may under no circumstances be pulled over sharp edges. Defective
high pressure hoses must not be repaired (acc. to DIN 20022) but have to
be replaced by new hoses approved by the manufacturer.

14
Putting into operation

1. Carry high pressure cleaner to its place

of operation. When parking the unit
make sure that the four rubber buffers
stand on a safe support.

2. Unwind high pressure hose straight

and without nooses. (When using hose
extensions take care that the max.
length of 20 m is not exceeded!)

Do not place high pressure cleaner on rough surface because unit tends to
vibrate during operation.

When carrying the high pressure cleaner, make sure to bear in mind the
weight of the machine, see technical data.

Neither set up or operate the K 1050 P in rooms where there is a risk of fire
or explosion nor put it into puddles. Do not use the machine under water.
If, none the less, the machine is operated in a hazardous area,
the applicable safety regulations are to be observed.

15
 Putting into operation

3. Push on high pressure hose to trigger

gun with safety catch.

4. Tightly screw together high pressure

hose and trigger gun with safety catch.

5. First pull back the retaining sleeve of

the gun, then insert lance into the
plug coupling connection of the gun.

6. After insertion of the lance, release reta-

ining sleeve and make sure that the lance
is in a secure position.

Prior to insertion, check plug coupling connection of lance for cleanliness

(sand, dirt ..) and use clear water to clean, if necessary.
Impurities may damage the sealing in the plug coupling.

16
Putting into operation

7. Check water inlet filter for cleanliness

prior to putting the machine into
operation. When inside filter is
contaminated, remove filter and follow
step 7.1.

7.1 If contaminated, remove sieve and

thoroughly rinse and clean with the
rest of the parts in clear water.

Check sieve for damages.

Do not operate high pressure without or with a damaged sieve.

8. Connect water hose to water inlet.

The cleaner may be connected to a
water mains (1-10 bar pre-pressure)
with either cold or hot water (up to
60°C).

Be careful when using hot water!

When running your high pressure cleaner with hot water of 60° C raised
temperatures occur. Do not touch the metal parts of the cleaner without
safety gloves!

17
 Putting into operation

9. Connect to circuit.
K 1050 P
230 V ~, 9.6 A, 50 Hz
The socket must be protected with a
16A fuse on the mains side.

Never touch plug or live parts with moist or wet hands.

10. Switch on HP cleaner with opened

trigger gun (trigger pulled). Bleeding of
the machine: Pull and release trigger
of trigger gun with safety catch several
times. Start cleaning task.

11. When using the Dirtkiller make sure

that lance points downward when
starting.

It is imperative that safety instructions be observed during use

of the machine.

18
To shut down the pump

1. Switch off the high pressure cleaner

2. Cut off the water supply
3. Open the trigger gun with safety catch briefly until the
pressure is released
4. Apply safety catch on the trigger gun
5. Remove water hose and trigger gun with safety catch
6. Drain the pump: switch on the motor for approx. 10 seconds
7. Pull the plug from the socket
8. Clean HP hose and wind up without loops
9. Clean power cable and wind up
10. Clean water filter
11. Store high pressure cleaners in frost-free rooms in winter

Due to their small base, the compact and

mobile Kränzle machines are easy to store.

19
 Small repairs - do it yourself!

Problem:
No water from nozzle although motor is running.

Cause:
Most likely the nozzle is blocked.
No or very little water from the lance.

Proceeding:
Switch off the cleaner. Pull plug from
the socket. Operate trigger gun with
safety catch several times to decrease the
pressure.

Unscrew trigger gun and lance first,

then rinse high pressure gun to remove
possible soiling.

Check water inlet filter for soiling.

If the problem still exists, take wire (paper

clip) and push through nozzle opening.
If cleaning by means of a wire is not
successful, replace lance.

Pull plug from socket prior to starting any repair work!

20
Small repairs - do it yourself!

Problem:
Irregular jet from nozzle.

Cause:
Most likely the valves are soiled or sticky.
The water from the lance comes in
squirts. The HP hose vibrates.

Proceeding:
Unscrew all 6 valves, one after the other
(hexagonal brass screws, 3 in a row,
vertically and horizontally)

Take out valve body (with green or red

plastic coating) and O-ring by means
of needle nose pliers. Check O-ring for
damage. In case of a damage the O-ring
has to be replaced.

Take a wire (paper clip) and clean valves

under running water.

Do not forget the O-ring during

reassembly!

21
 Small repairs - do it yourself!

Problem:
After closing of the trigger gun with safety catch the machine keeps switching
on and off.

Possible cause no.1:

Leakage.

Having closed the trigger gun with safety

catch, the HP cleaner must shut down.
Failure to shut down may be caused by
leakage in the pump, the pressure switch,
the high pressure hose or the trigger gun
with safety catch.

Proceeding:
Check connections from the HP cleaner to
the high pressure hose and from the hose
to the trigger gun and also the connecti-
on between lance and trigger gun for
tightness.

Switch off the cleaner. Shortly press the

trigger of the trigger gun with safety
catch to decrease the pressure. Unscrew
HP hose, trigger gun with safety catch
and lance and check the O-rings. If the
O-rings are damaged they have to be
replaced.

In case of a leakage there is no guarantee

for possible consequential damages.

22
Small repairs - do it yourself!

Problem:
After closing of the trigger gun with safety catch the machine keeps switching
on and off.

Possible cause no. 2:

The non-return valve is defective.

Proceeding:
Switch off the HP cleaner and pull plug from
socket. Stop water supply. Unscrew pump
outlet.

Remove check body and check O-Ring for

soiling or damage.
Also check seal seat inside pump housing
for soiling or damage.

If sealing rings are defective replace

O-rings at once.

There is no guarantee if the pump is damaged by

defective O-rings due to air induction or lack of water (cavitation).

23
 EC declaration of conformity

We hereby declare that the design of the

high pressure cleaners: Kränzle 1050 P

Nominal flow: 450 l/h

technical specifications available from: Fa. Josef Kränzle GmbH & Co. KG
Manfred Bauer
Rudolf-Diesel-Str. 20, 89257 Illertissen

comply with the following guidelines Machinery directive 2006/42/EC

and their amendments for high pressure EMC-directive 2004/108/EC
cleaners: Noise directive 2005/88/EC,
Art. 13 HP water spraying machines
Annex 3, part B, chapter 27

Sound level measured: 84 dB (A)

guaranteed: 86 dB (A)

Applied conformity assessment Annex V, Noise directive

procedure: 2005/88/EC

Applied specifications and standards: EN 60 335-2-79 :2015

EN 55 014-1 :2006
EN 61 000-3-2 :2014
EN 61 000-3-3 :2013

Ingrid Kränzle GmbH

Elpke 97
D - 33605 Bielefeld
Josef Kränzle
Bielefeld, June 15, 2015 (Managing director)

24
Wiring diagram

Capacitor 35 µF
P

Clamp

P2
N
Hi Ha P1
L1
Motor over
temperature-switch
PE

25
 Warranty

Warranty

Our warranty obligation is understood to exclusively cover material and

manufacturing defects; wear is not covered by warranty.

The machine is to be operated in conformity with this Operating manual.

The operating manual is deemed to be part of the warranty provisions. This
warranty shall only apply on condition of proper use of original-Kränzle
component parts and original-Kränzle replacement parts.

With regard to legal warranty claims, the limitation periods of the respective
countries shall apply.

In the event of any warranty claims, please have your accessories and purchase
voucher ready before contacting your local dealer or the nearest authorized
customer service point, which you can also find in the internet under
www.kraenzle.com .

The high pressure cleaner is designed for private purposes only; no warranty
shall be provided in case of industrial use.

In case of any modifications on the safety installations or in case of exceeding

the temperature and speed limit, any warranty claims shall become invalid - this
shall also apply to undervoltage, lack of water and use of wastewater as well as
any other faulty or inappropriate operation of the machine.

Pressure gauge, nozzle, valves, sleeves, high pressure hose and spray equipment
are wear parts and are not covered by the Warranty obligation.

26
Notes

27
 Spare parts list complete assembly

40

41
30

42
10

11 3
14
13

28
K 1050 P

Pos. Bezeichnung Stück Art.-Nr.

1 Seitenschale 1 49.170
3 Abdeckung 1 49.171
4 Gummi-Metall-Anschlagpuffer 25 x 30 Ø5,2 4 49.010
6 Kunststoffschraube 5x14 4 43.426
10 Kunststoffschraube 5x30 5 43.418
11 Kunststoffschraube 5x20 4 50.157
13 Kabelklemme 1 43.431
14 Schraube 3,5 x 14 2 44.525
30 Schlauch NW 6 8 m 1 41.054 1
40 Pistole M2000 mit Stecksystem DN10 1 12.475
41 Lanze mit Flachstrahldüse 1 12.900-03
42 Lanze mit Schmutzkillerdüse (optional) 1 42.403-03

29
 Spare parts list motor

14

27 41

25
19
26

18

22
21
12
15 15

13
28
29
30
11

24

6 7
9 4

8
10

5
17
1

30
K 1050 P

Pos. Bezeichnung Stück Art.-Nr.

1 Motor 230V / 50 Hz komplett ohne Elektrik 1 49.260
4 Haube Luftführung 1 49.283
5 Motor-Lager B-Seite 6203 1 49.288
6 Motor-Lager A-Seite 7304 1 41.027
7 Öldichtung 25 x 35 x 7 1 41.024
8 Lüfterrad 1 49.281
9 Wellensicherungsring 17 x 1 1 49.282
10 Lagerbolzen Stator 2 49.284
11 Gummidichtung 1 49.287
12 Lüfterklemme 3-pol. 1 43.031 2
13 Schaltkasten Unterteil 1 49.104
14 Ein-Aus-Schalter 1 49.112
15 Durchführungstülle Druckschalter- und Netzkabel 2 49.115
17 Gummilager Stator 4 49.285
18 Kondensator 35µF 1 41.114 4
19 Netzanschlusskabel für 3 x 1,0 mm² (EU) 1 49.114
19.1 Netzanschlusskabel für 3 x 1,0 mm² (GB) 1 49.121
19.2 Netzanschlusskabel für 3 x 1,0 mm² (CH) 1 49.120
19.3 Netzanschlusskabel für 3 x 1,0 mm² (SA) 1 49.123
21 Schraube 3,5 x 20 2 43.415
22 Innensechskantschraube M6 x 16 4 44.831
24 Erdungsschraube kpl. 1 43.038
25 Deckel für Schaltkasten 1 49.105
26 Dichtung für Deckel 1 49.113
27 Kunststoffschraube 5,0 x 20 4 43.018
28 Scheibe Ø 6,4 4 50.189
29 Federing Ø 6,1 4 44.222 1
30 Schraube M 6 x 30 4 43.037

41 Schaltkasten komplett 1 49.150

Pos. 11 - 15, 18, 21, 22, 25 - 27

31
 Spare parts list transmission

9
14

6 7

5
4

3 8
13

10

32
K 1050 P

Pos. Bezeichnung Stück Art.-Nr.

1 Gehäuseplatte 1 49.200
2 Öldichtung 12 x 20 x 5 3 43.081
3 O-Ring 78 x 2 1 49.201
4 Plungerfeder 3 49.203
5 Federdruckscheibe Ø12mm 3 49.219
6 Plunger 12 mm AC mit Wellensicherungsring 3 49.209
7 Wellensicherungsring Ø12mm 3 49.230
8 Taumelscheibe 10,0° 1 49.202-10,0
9 Öleinfüllschraube 1 43.437
10 Axial-Rillenkugellager 3-teilig 1 49.208
13 Schraube M 6 x 30 4 43.037
14 O-Ring 14 x 2 1 43.445

Oil change
If oil needs to be changed during repair, the unit is to turned into horizontal
position with its head upside down prior to unscrewing the drain plug over a
container. The oil is to be captured in a container and subsequently properly
disposed of. Then screw oil plug back on again over a container. Use small
funnel when refilling with fresh oil.
Fresh oil: 0.1 l - Kränzle Gear Oil (40.092 2) or W 15/40.

33
 Spare parts list pressure switch

13
15
12
11
14

50

51

34 35

34
K 1050 P

Pos. Bezeichnung Stück Art.-Nr.

11 Rückschlagkörper 1 14.122
12 Rückschlagfeder 1 14.120
13 Ausgangsteil 1 49.232
14 O-Ring 6 x 3 1 49.234
15 O-Ring 16 x 2 1 13.150
35 O-Ring 6,0 x 2,5 2 49.233
37 Schraube 2,9 x 13 8 12.292

50 Start-/Stop-Ventil komplett 49.240

51 Mikroschalter mit Gehäuse kpl. 49.241

35
 Spare parts list valve housing

19
19.1
7

5 6 10
9
61 8
10

60
3
4
2
40

18

36
K 1050 P

Pos. Bezeichnung Stück Art.-Nr.

1 Ventilgehäuse 1 49.204
2 Ventilstopfen mit integr. Ventil 6 43.066
3 O-Ring 10 x 2 6 43.068
4 O-Ring 12 x 2 6 15.005 1
5 Dichtstopfen M 8 x 1 1 13.158
6 Dichtstopfen M 10 x 1 1 43.043
7 Distanzring mit Abstützung 3 49.205
8 Leckagering 3 49.206
9 O-Ring 22 x 2 3 49.225
10 Manschette 12 x 20 x 5,2 6 49.226
18 Innensechskantschraube M 6 x 80 4 49.227
19 Stopfen M 10 x 1 1 13.385
19.1 O-Ring 6 x 1,5 1 13.386
40 Wassereingangsfilter 1 13.311

60 Reparatursatz Ventile 43.096 1

61 Reparatursatz Manschetten 49.242

37
 Spare parts list gun with lance

2
6

10

Pos. Bezeichnung Stück Art.-Nr.

1 Pistolenschale rechts + links 1 12.450
2 Schraube 3,5 x 14 10 44.525
6 Düsenschutz Jet-Düse 1 26.021

10 Reparatursatz M2000 Midi-Mechanik 12.461

38
Spare parts list
Dirtkiller with lance (optional)

1
11 20

Pos. Bezeichnung Stück Art.-Nr.

1 Sprühkörper 1 41.950
6 O-Ring 16 x 2 1 40.016 1
11 Schutzkappe 1 41.952
12 Kappe hinten für Schmutzkiller 03 1 41.953-03

20 Reparatursatz Schmutzkiller 03 1 41.955-03

39
 Technische Änderungen und Irrtümer vorbehalten.
Ingrid Kränzle GmbH

Stand 15.06.2015, Art.-Nr. 30.610 0

Elpke 97
33605 Bielefeld (Germany)

Telefon: +49 (0) 521 / 9 26 26-0

Telefax: +49 (0) 521 / 9 26 26-40

[email protected]

Made
in
Germany

www.kraenzle.com