1.

Requirements to the power

Shaft Vertical View The top of shaft Main Power 220V, 1-Phase ,60Hz ,Max tolerance
allowed ¡À7% Illumination Power 110V.
A separate and insulative ground wire with the same
Lift hook at user's diameter as the power wire must be required in
machine room. But it should not be arranged in the
charge same trunk, the ground resistance should not be
100

Lift hook bearing:1500kg 100 Floor plan of pit above 4ohm.

Hoistway plane layout The main power and the lighting should be as
(it should be marked in possible as close to the machine room door by the
client, the main switch should be located
the lift hook) approximately 1.5 meter above the floor and 0.3
meter from the door,meanwhile connect power cable
795 to the switch box.
≤450

2. Requirements to the shaft

655 575 140 DBG 862 The dimensions of lift shaft in horizontal is the
140 minimum net measurement by plumb. Allowable
DBG 862 tolerance:
Shaft structure are strongly recommanded to be
concrete. If bricky situation, adding structure beam to
F3

CWT DBG 700

the position of brackets locates should be taken into
P1

HD 1400
P2 account, with height not less than 350mm.
CWT DBG 700

When front wall of shaft is bricky, a lintel used to

355 355
CD 1000

fasten brackets should be added above the hole of

HD 1400
320
40

landing door, with height not less than 250mm.

200

Concrete pillars for oil buffers in the pit are made

OH=3200

200 F2 F1
741
under the guidance of the lift erectors, and can stand

891
891
for the impact force given in the table, these should be
CW 750
rail bracket support Z1 per-step interval ≤1500

anti-water layers in the pit.

50 F4 Be sure no accessible way for human in pitset.Ladder
in pit ,ladder and protected barrier in machine room (if
necessary) should be installed.
30

3. Requirements to the machine-room

120

OP 700 370 SOW 900 100 Path for appalince carrying should be taken into
account.The entrance to the machine room should not
370 SOW 900 100 be blocked, the floor surface in the machine room
HW 1370 should be flattened, and can bear the load of
HW 1370 700kg/square meter (Noted load excluded).
The machine room can be locked and should be kept
dry, ventilative and clean. Humidity degree should not
be more than 85 %.Temperature in the machine room
allowed,+5C ~ +40
Lighting in the machine room should be above 200 Lux.
4. Other requirements
Beam of CWT Side Beam of CAR Side Excavation in the drawing for indicators and car call
boxes are the construction sizes.Please refer to the
manufactory if construction plane made of marble.
The load except for P1,P2 are static load!Dynamic
load coefficient is 2

450
850
Pivot point bearing (Newton)

300
P1 38000 F1 32000

300
intel beam height300
Floor spaoer 2600

P2 30000 F3 16000
Travelling

F1 17000 F4 20000
Technical description
Elevator Model TSJ(320/0.4-JXW)
Surface HOP Hoistway Size 1370 X 1400
Hole with ∅40 Car Size

OH
150 (CW*CD)
750 X 1000
2 By client Door Opening Mode S0

SOH 2100

OPH 2000
Door Opening Size 700 X 2000
Main Power Supply AC220V ，60Hz，

≤1500
320KG Speed(m/s) 0.4m/s

1300
Load capacity
Control mode JWX Kw 0.9Kw
Goveming means VVVF Mctor power
Construction floor
>38

Over Head 3200

300
MAX Rise Pit Depth 500
OH project
OP 700 name
PP=500
SOW 900 4F
Hoistway width 1370 3F
2F
Drawn SYB
K View 1F
安装时以电梯随机资料中盖有“电梯安装用 -1F CHK CWL
图”字样的图纸作为电梯安装用图 PP
Drawing
No.