Scribd
Upload
25 views

Weekly Schedule Textile Testing and Quality Control

This document outlines a 16 week course plan covering topics in textile testing and quality control. The plan lists weekly topics that will be covered through readings, handouts, and other supplemental materials. Topics include fibre, yarn and fabric testing methods, quality inspection and control, seam performance, and labelling requirements.

Uploaded by

Dr-Ahmer Hussain Shah
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
25 views

Weekly Schedule Textile Testing and Quality Control

This document outlines a 16 week course plan covering topics in textile testing and quality control. The plan lists weekly topics that will be covered through readings, handouts, and other supplemental materials. Topics include fibre, yarn and fabric testing methods, quality inspection and control, seam performance, and labelling requirements.

Uploaded by

Dr-Ahmer Hussain Shah
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

COURSE PLAN WEEKLY BASIS

Reading/
Chapter/
Handout
s/
Weeks Topics Remarks
Other
Supplem
ent
Material
Introduction HAND
Testing Methods (Sources of Testing Standards OUTS
Week-1 Selection of Samples for Testing
Sampling for Textile Testing
Fibre Sampling Techniques
Yarn Sampling Techniques HAND
Fabric Sampling Techniques OUTS
Week-2 Standard Atmosphere for Testing
Measurement of Moisture Regain
Effect of moisture on physical properties: dimensional, HAND
mechanical and electrical. Atmospheric moisture: vapour OUTS
pressure, relative humidity, standard atmosphere
Measurement of atmospheric moisture.
Regain and moisture content: regain, factors affecting the
regain, method of measuring regain.
Correct invoice weight. Control of testing room atmosphere.
Week-3
Fibre Fineness Measurement
Fibre Length Measurement
Cotton Maturity Measurement
Fibre Strength Measurement
Determination of Trash and Lint in Cotton
High Volume Instrument (HVI)

Yarn Numbering System (Count) HAND


Determination of Yarn Count OUTS
Determination of Yarn Strength
Determination of Yarn Twist
Week-5 Measurement of Yarn Evenness
Yarn Faults & Classification
Measurement of Yarn Hairiness

Fabric Particulars - length, width, crimp, weight, cover factor HAND


Fabric Strength - tensile strength tester, tearing strength tester, OUTS
Week-6 hydraulic bursting strength tester

Fabric Abrasion - Martindale abrasion tester HAND


Fabric Pilling - I C I Pill box tester OUTS
Fabric drape –Measurement by Drape meter
Fabric Stiffness - Shirley stiffness tester
Week-7
Fabric crease resistance and crease recovery-measurement of
crease recovery
Fabric permeability - Shirley air permeability tester, fabric
permeability to water, Bundesmann tester

Colour Fastness to Crocking, Perspiration, Sunlight, Laundering, HAND


Dry Cleaning, Hot Pressing OUTS
Week-8 Colour Matching - Colour Matching Cabinets, Computer Colour
Matching System
Objective Evaluation of Fabric Hand by KES and FAST Systems
Mid Semester Examination

Raw material & In-process inspection HAND


Week-9 Final inspection OUTS
4-point system and 10-point system of fabric inspection

Seam efficiency and performance HAND


Factors affecting the seam strength OUTS
Week-10 Relation between seam strength and different parameters
Ease allowance in garment design and its role in physical comfort

Labelling – fibre, fur and faux fur, care instructions, stuffed articles HAND
(law labels) and country of origin OUTS
Week-11 Mechanical hazards – drawstrings, small parts and sharp
points and edges

Control of raw materials; standard controls HAND


Week-12 Off –line process control OUTS

Classification and detection of faults HAND


Statistical control methods OUTS
Week- 13 Quality incentives
Visual faults in fabric

Week-14 Class presentations


Week-15 Class presentations
Week-16 Quiz and revision of topics if required

Final semester Examination

All the lecture classes will be conducted in Textile testing and Quality control Lab located in

CAD CAM laboratory as per time table i.e. Wednesday 11:00 to 2:00.

You might also like