6.

Power Supply Specification

User’s manual of SAVCH MPU v1.0 Copyright © 2017 SAVCH Electric Co.,Ltd Power Supply Voltage
Item
100~240VAC
AC Power Supply

Power Supply Frequency 50~60Hz

1. Products receiving Power Consumption 25VA MAX
Instantaneous Surge 20A 1.5ms MAX @220VAC
All products have been performed with strict test and inspection. After receiving the inverters, the following checks shall be performed. Power Loss Time 20ms or less @220VAC
●To check that SAVCH inverter, an instruction manual is inside of the package Fuse 2A, 250VAC
●To check whether model number correspond with model your purchase order. 5V Output Voltage (for CPU) 5V, -2%~+2%, 1.2A MAX
●To check whether there are damaged parts during transportation and delivering. If there are, do not connect with power supply. 24V Output Voltage (for output and extension) 24V, -15%~+15%, 500mA MAX
If any of the above checkpoints are not satisfactory, contact your SAVCH ELECTRIC representative for a quick resolution. 24V Output Voltage (for input and peripheral) 24V, -15%~+15%, 300mA MAX
Insulation Type Transformer isolation or optoelectronic isolation,1500VAC/1 minute
2. Model description Power Protection DC24V output over current

S M C - E 16 M R 7.Environmental specifications for Product

Item Environment Specification
Temperature/Humidity Operating temperature:0~+55℃ Storage temperature:-25~+70℃ Humidity: 5~95%RH, No condensation
Product name Output type: Vibration Resistance 10~57 HZ, amplitude=0.075mm, 57HZ~150HZ acceleration=1G, 10 times each for X-axis, Y-axis and Z-axis
R（Relay） Impact Resistance 15G, duration=11ms, 6 times each for X-axis, Y-axis and Z-axis
T（Transistor） Interference Immunity AC EFT:±2500V Surge:±2500V DC EFT:±2500V Surge:±1000V
Over Voltage Resistance 1500VAC/1min between AC terminal and PE terminal, 500VAC/1min between DC terminal and PE terminal
Product Series Module type:
E（Economic PLC MPU） Insulation Impedance ≧5MΩbetween AC terminal and all input/output points to PE terminal @500VDC
M（Main）
S（Standard PLC MPU） Ground The third kind of grounding(Connecting to the ground of high voltage system is prohibited)
E（Extension module）
Operating environment Avoid dust, moisture, corrosion, electric shock and external shocks
H（High performance PLC MPU）
I/O point：
M（Motion control PLC MPU）
Built-IO:16-point,24-point,32- 8. Digital Input (DI) / Output (DO)Specification
point,48-point,60-point are optional Input（DI） Output（DO）
Item Digital Input (DI) Item Output point type : Relay - R Output point type :Transistor - T
3. External dimensions Input Signal No voltage contact or NPN/PNP Resistive Load 2A/1 point, 8A/4 points COM 0.5A/1 point, 2A/4 points COM
Maximu
Action driving ON>3.5mA OFF<1.5mA Inductive Load 50VA 5W/DC24V
m load
Type 220VAC power supply Dimension Input Impedance Input Impedance≈4.3KΩ Lamp load 100W 12W/DC24V
Maximum Input Minimum Load 10mA 2mA
SMC-E16MR 5 VA 10mA
Current Voltage Specification Below 250VAC, 30VDC 30VDC
SMC-E16MT 5.5VA 6.4ms DEFAULT, can be configured to
Reaction Time Maximum contact capacity:
SMC-S16MR 5 VA 93×95×82mm 0 1 2 3 0.8~51.2ms Drive Capability 1A MAX, 10 seconds
AI
5A/250VAC
SMC-S16MT 5.5VA Insulation Type Optoelectronic isolation for each channel
Reaction Time Off-on 10ms，On-off 5ms Off→On 10us，On→Off 120us
PWR
LINK
SMC-E16MR
Input Indication LED's lighting indicates ON, no light indicates OFF
SMC-M24MT 6.5VA Optoelectronic isolation for each
MPU internal power supply:DC power supply Insulation Type Mechanical isolation
SMC-E24MR 5.5VA
AI
Power supply channel
4 5 6 7
(SINK or SOURCE) 5.3mA@24VDC
SMC-E24MT 6.5VA Output Indication LED's lighting indicates ON, no light indicates OFF
Power Supply MPU internal 24VDC power supply
SMC-S24MR 5.5VA
SMC-S24MT 6.5VA
9.Digital Input/Output (DI/DO) Wiring
SMC-E32MR 5.5VA 131×95×
SMC-E32MT 6.5VA 82mm
SMC-S32MR 5.5VA
SMC-S32MT 6.5VA
SMC-H40MR 6.5VA 0 1 2 3 4 5 6 7
8 9 10 11 12 13 14 15
0 1 2 3 4 5 6 7
8 9 10 11 12 13 14 15
16 17 18 19
95.0

SMC-H40MT 7.5VA
16 17 18 19 20 21 22 23
DI(X)

95.0
24 25 26 27 28 29 30 31
DI(X)
PWR
SMC-S32MR PWR
LINK SMC-M60MT

SMC-E48MR 6.5VA DI(X)

LINK
DO(Y)
0 1 2 3 4 5 6 7
20 21 22 23 24 25 26 27 8 9 10 11 12 13 14 15

SMC-E48MT 7.5VA 28 29 30 31 32 33 34 35
36 37 38 39
16 17 18 19 20 21 22 23
24 25 26 27 28 29 30 31

SMC-S48MR 6.5VA
SMC-S48MT 7.5VA
177×95×
SMC-E60MR 7.5VA
82mm 123.0 168.7
SMC-E60MT 8 VA 131.0 177.0
SMC-S60MR 7.5VA 10.Programming Cable Wiring
SMC-S60MT 8 VA
SMC-M60MT 8.5VA

4. Mounting and installation

The PLC should be secured to an enclosed cabinet while mounting. For heat dissipation, make sure to provide a minimum
clearance of 50mm between the unit and all sides of the cabinet. (See the figure.)
Rail Mounting: Use standard 35 mm rail. Computer side (RS-232) DB9 female PLC side(COM1) 4 core S terminal male
Screw Mounting: Each MPU or extension module has two positioning screw holes, the diameter of the hole is 4.5mm. Please refer
to the dimension figure for the location of the positioning holes and their spacing.
11. Adress Setting
To avoid over temperature and for a better heat dissipation, do not mount PLC to a position near to the bottom/top Haiwell PLC with Ethernet port,the default IP address is : 192.168.1.111,subnet mask: 255.255.255.0, gateway: 192.168.1.1.Hardware DIP dial switch
of the cabinet. Do not mount PLC in vertical direction. address range: 1-15, the default address is 1. If you need to set a bigger adress range, you can set on the software after connection with PLC, it can
Extension Module Wiring: Connections between extension modules and connections between module and MPU are achieved be set on the PLC parameter option in the sofware menu by checking on the "soft address" with the range of 1-254(the soft address is prior to the
through bus.An extension cable will be configured to every extension module, for the connection hardware dial address).
between two different modules.Connection methods: turn the right side of extended interface(the last
MPU or extension module) over, plug the extension cable in the extended interface, then press down the 12. Power Supply Wiring
cover of the extended interface to reset the interface, the extended interface at the right side of the  Input voltage is 100~240VAC 50/60Hz unless otherwise stated. Connecting any one of the AC input wires to the terminal-L and terminal-N on the MPU will be OK, but for safety's sake,
module will be reserved for extension of the next module. Connect all extension modules in turn in the
please connect the two wires (Live Wire & Neutral Wire) of AC input to terminal-L and terminal-N respectively.
same way.
 Any AC110V or AC220V connected to the +24V terminal or input points will permanently damage the PLC.
5.Indicator Description  Please use wires of 2.5mm or above for the grounding of the MPU.
① PWR:Power indicator,green. Continuous ON - Power good; OFF - Power error.
② RUN:Running indicator,green. Continuous ON - PLC is in running state; OFF - PLC was shutdown.
③ COM:Communication indicator,green. Flickering - PLC is in communicating state, the flicker frequency indicates the speed of the communication; OFF - No communication.
④ ERR:Erroe indicator .double(red. yellow),as follows.
Thanks for choosing SAVCH PLC, If you have any questions about our products or services, please let us know!
ERR the state of the indicator Signify information type Consult manage
Not light Without error Normal
Shanghai Office:
Yellow flicker:On 0.2 seconds and Off 0.8 Room 1410-1411,4# Building, Yatai square, Huaqiao international Business City)
PLC have the component which locked Normal,just prompt take attention to the locked data
seconds Tel：021-59275902 Fax：021-59275902
Yellow flicker:On 0.2 seconds and Off 0.8 Problem in the soft seting ,permit user keep on operate the user
Modificate the PLC hardward configure
seconds program Quanzhou Factory: Quanzhou Sangchuan Electric Equipment Co.,Ltd
Yellow flicker:On 0.8 seconds and Off 0.2 Communication abnormal between modul,auto dislodge the Check module parallel bus (check the RTC battery; check 3# Zixin Road, Jiangnan Hi-Tech Industrial Park, Quanzhou, Fujian, China
seconds abnormal module,permit user keep on operate the user program extension module power supply) Tel：0595-24678200 Fax：0595-24678203
Red slowly flicker:indicator light 0.5s not Fireware abnormal or user program abnormal,can not operate the
Upgrade the fireware or modify the user program
light 0.5s user program
Savch Website：www.savch.net E-mail：[email protected] Savch wechat
yellow constant light Hardware error,user program con not running Maintain
service number