FILE NO.

050-200312

SERVICE MANUAL

COLOR TELEVISION

20A23

DOCUMENT CREATED IN JAPAN, May, 2003

 SERVICING NOTICES ON CHECKING
1. KEEP THE NOTICES 6. AVOID AN X-RAY
As for the places which need special attentions, Safety is secured against an X-ray by consider-
they are indicated with the labels or seals on the ing about the cathode-ray tube and the high
cabinet, chassis and parts. Make sure to keep the voltage peripheral circuit, etc.
indications and notices in the operation manual. Therefore, when repairing the high voltage pe-
ripheral circuit, use the designated parts and
2. AVOID AN ELECTRIC SHOCK
make sure not modify the circuit.
There is a high voltage part inside. Avoid an Repairing except indicates causes rising of high
electric shock while the electric current is voltage, and it emits an X-ray from the cathode-
flowing. ray tube.
3. USE THE DESIGNATED PARTS 7. PERFORM A SAFETY CHECK AFTER
The parts in this equipment have the specific SERVICING
characters of incombustibility and withstand
Confirm that the screws, parts and wiring which
voltage for safety. Therefore, the part which is
were removed in order to service are put in the
replaced should be used the part which has
original positions, or whether there are the
the same character.
portions which are deteriorated around the
Especially as to the important parts for safety
serviced places serviced or not. Check the
which is indicated in the circuit diagram or the
insulation between the antenna terminal or
table of parts as a mark, the designated
external metal and the AC cord plug blades.
parts must be used.
And be sure the safety of that.
4. PUT PARTS AND WIRES IN THE (INSULATION CHECK PROCEDURE)
ORIGINAL POSITION AFTER
1. Unplug the plug from the AC outlet.
ASSEMBLING OR WIRING 2. Remove the antenna terminal on TV and turn
There are parts which use the insulation on the TV.
material such as a tube or tape for safety, or 3. Insulation resistance between the cord plug
which are assembled in the condition that terminals and the eternal exposure metal
these do not contact with the printed board. [Note 2] should be more than 1M ohm by
The inside wiring is designed not to get closer using the 500V insulation resistance meter
to the pyrogenic parts and high voltage parts. [Note 1].
Therefore, put these parts in the original 4. If the insulation resistance is less than 1M
positions. ohm, the inspection repair should be
required.
5. TAKE CARE TO DEAL WITH THE
[Note 1]
CATHODE-RAY TUBE
If you have not the 500V insulation
In the condition that an explosion-proof cathode-
resistance meter, use a Tester.
ray tube is set in this equipment, safety is
secured against implosion. However, when [Note 2]
removing it or serving from backward, it is External exposure metal: Antenna terminal
dangerous to give a shock. Take enough care to Earphone jack
deal with it.

HOW TO ORDER PARTS

Please include the following informations when you order parts. (Particularly the VERSION LETTER.)
1. MODEL NUMBER and VERSION LETTER
The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be
found at the end of the SERIAL NUMBER.
2. PART NO. and DESCRIPTION
You can find it in your SERVICE MANUAL.

IMPORTANT
Inferior silicon grease can damage IC's and transistors.
When replacing an IC's or transistors, use only specified silicon grease (YG6260M).
Remove all old silicon before applying new silicon.

A1-1
 TABLE OF CONTENTS

SERVICING NOTICES ON CHECKING ..................................................................................... A1-1

HOW TO ORDER PARTS .......................................................................................................... A1-1
IMPORTANT ............................................................................................................................... A1-1
TABLE OF CONTENTS .............................................................................................................. A2-1
GENERAL SPECIFICATIONS .................................................................................................... A3-1~A3-5
DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF ANODE CAP ............................................................................................... B1-1
2. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ................................................ B2-1, B2-2
SERVICE MODE LIST ................................................................................................................ C1-1
CONFIRMATION OF HOURS USED ......................................................................................... C1-1
WHEN REPLACING EEPROM (MEMORY) IC .......................................................................... C1-1
ELECTRICAL ADJUSTMENTS .................................................................................................. D-1~D-5
BLOCK DIAGRAMS ................................................................................................................... E-1, E-2
PRINTED CIRCUIT BOARDS
MAIN/CRT ................................................................................................................................ F-1~F-4
SCHEMATIC DIAGRAMS
MICON/CHROMA/TUNER ...................................................................................................... G-1, G-2
DEFLECTION/CRT .................................................................................................................. G-3, G-4
TV POWER .............................................................................................................................. G-5, G-6
SOUND .................................................................................................................................... G-7, G-8
AV ............................................................................................................................................ G-9, G-10
WAVEFORMS ............................................................................................................................. H-1, H-2
MECHANICAL EXPLODED VIEWS ........................................................................................... I-1
MECHANICAL REPLACEMENT PARTS LIST ......................................................................... J1-1
ELECTRICAL REPLACEMENT PARTS LIST ........................................................................... J2-1~J2-3

A2-1
 GENERAL SPECIFICATIONS
G-1 TV CRT CRT Size / Visual Size 20 inch / 508.0mmV
System CRT Type Normal
Deflection 90 degree
Magnetic Field BV/BH +0.45G/0.18G
Color System NTSC
Speaker 1Speaker
Position Front
Size 1.6 x 2.8 Inch
Impedance 8 ohm
Sound Output MAX 1.5 W
10%(Typical) 1.0 W
NTSC3.58+4.43 /PAL60Hz No
G-2 Tuning Broadcasting System US System M
System Tuner and System 1Tuner
Receive CH Destination USA(W/ CATV)
Tuning System F-Synth
Input Impedance VHF/UHF 75 ohm
2 - 69, 4A, A-5 - A-1,
CH Coverage A - I, J - W, W+1 - W+84
Intermediate Picture(FP) 45.75MHz
Frequency Sound(FS) 41.25MHz
FP-FS 4.50MHz
Preset CH No
Stereo/Dual TV Sound No
Tuner Sound Muting Yes
G-3 Power Power Source AC 120V AC 60Hz
DC
Power Consumption at AC
80 W at AC 120 V 60 Hz
Stand by (at AC) 5 W at AC 120 V 60 Hz
Per Year -- kWh/Year
Protector Power Fuse Yes
G-4 Regulation Safety UL/CSA
Radiation FCC/IC
X-Radiation DHHS/HWC
G-5 Temperature Operation +5oC ~ +40oC
Storage -20oC ~ +60oC
G-6 Operating Humidity Less than 80% RH

A3-1
 GENERAL SPECIFICATIONS
G-7 On Screen Menu Yes
Display Menu Type Character
Picture Yes
Contrast Yes
Brightness Yes
Color Yes
Tint Yes
Sharpness Yes
Audio No
Bass No
Treble No
Balance No
BBE On/Off No
Stable Sound On/Off No
Surround On/Off No
CH Set Up Yes
TV/CABLE(CATV) Yes
Auto CH Memory Yes
Add/ Delete Yes
Lock Yes
CH Lock Yes
Video Lock Yes
Game Timer Yes
Change Password Yes
On Timer Yes
Language Yes
V-chip Yes
CH Label No
Favorite CH No
Color Stream DVD/DTV No
Control Level Yes
Volume Yes
Brightness Yes
Contrast Yes
Color Yes
Tint Yes
Sharpness Yes
Tuning No
Bass No
Treble No
Balance No
Stereo,Audio Output,SAP No
Video Yes
Color Stream No
Channel(TV/Cable) Yes
CH Label No
Game Timer Yes
Sleep Timer Yes
Sound Mute Yes
V-chip Rating Yes
16: 9 No
G-8 OSD Language English French Spanish

G-9 Clock and Sleep Timer Max Time 120 Min

Timer Step 10 Min
On Timer Program(On Timer ) Yes
Wake Up Timer No
Timer Back-up (at Power Off Mode) more than -- Min Sec

A3-2
 GENERAL SPECIFICATIONS
G-10 Remote Unit RC-EH
Control Glow in Dark Remocon Yes
Format Toshiba
Custom Code 40-BF h
Power Source Voltage(D.C) 3V
UM size x pcs UM-4 x 2 pcs
Total Keys 27 Keys
Keys Power Yes
1 Yes
2 Yes
3 Yes
4 Yes
5 Yes
6 Yes
7 Yes
8 Yes
9 Yes
0 Yes
100 No
CH Up Yes
CH Down Yes
Volume Up Yes
Volume Down Yes
TV/Caption/Text Yes
CH1/CH2 Yes
TV/Video(TV/AV) Yes
CH RTN/CH ENT(Quick View) Yes
Sleep Yes
RE Call(Call) Yes
Reset Yes
Menu Yes
Enter Yes
Mute Yes
Exit No
MTS(Audio Select) No
Set + Yes
Set - Yes
16: 9 No
Multi Brand Keys CH Up(VCR) No
CH Down(VCR) No
Pause/Still No
TV/VCR(VCR) No
Code No
FF No
Rew No
Rec No
Play No
Stop No
TV No
VCR No
Cable No

A3-3
 GENERAL SPECIFICATIONS
G-11 Features Auto Degauss Yes
Auto Shut Off Yes
Canal+ No
CATV Yes
Anti-theft No
Rental No
Memory(Last CH) Yes
Memory(Last Volume) Yes
V-Chip Yes
Type USA,ORION Type
BBE No
Auto Search No
CH Allocation No
SAP No
Just Clock Function No
CH Label No
VM Circuit No
Full OSD No
Premiere No
Comb Filter No
Lines
Auto CH Memory Yes
Hotel Lock No
Closed Caption Yes
Stable Sound No
FBT Leak Test Protect Yes
CH Lock Yes
Video Lock Yes
Game Timer Yes
Energy Star No
Favorite CH No
Surround No
16:9 Mode No
G-12 Accessories Owner's Manual Language English / French
W/ Warranty Yes
Remote Control Unit Yes
Rod Antenna No
Poles
Terminal
Loop Antenna No
Terminal
U/V Mixer No
DC Car Cord (Center+) No
Guarantee Card No
Warning Sheet No
Circuit Diagram No
Antenna Change Plug No
Service Facility List No
Important Safety Instruction Yes
Dew/AHC Caution Sheet No
AC Plug Adapter No
Quick Set-up Sheet No
Battery Yes
UM size x pcs UM4 x 2
OEM Brand No
AC Cord No
AV Cord (2Pin-1Pin) No
Registration Card (NDL Card) Yes
ESP Card Yes
PTB Sheet No
300 ohm to 75 ohm Antenna Adapter No

A3-4
 GENERAL SPECIFICATIONS
G-13 Interface Switch Front Power Yes
System Select No
Main Power SW No
Sub Power No
Channel Up/Reset Yes
Channel Down/Enter Yes
Volume Up/Set Up Yes
Volume Down/Set Down Yes
MENU=Volume Up+Volume Down Yes
Rear AC/DC No
TV/CATV Selector No
Degauss No
Main Power SW No
Indicator Power Yes(RED)
Stand-by No
On Timer No
Terminals Front Video Input RCA
Audio Input RCA x 1
Other Terminal No
Rear Video Input(Rear1) No
Video Input(Rear2) No
Audio Input(Rear1) No
Audio Input(Rear2) No
Video Output No
Audio Output No
S-Input No
Color Stream No
Diversity No
Ext Speaker No
DC Jack 12V(Center +) No
VHF/UHF Antenna Input F Type
AC Outlet No
G-14 Set Size Approx. W x D x H (mm) 506.5 x 484 x 464.5
G-15 Weight Net (Approx.) 21.0kg ( 46.3 lbs)
Gross (Approx.) 23.8kg ( 52.5 lbs)
G-16 Carton Master Carton No
Content ---- Sets
Material -- /--
Dimensions W x D x H(mm) -- x -- x --
Description of Origin No
Gift Box Yes
Material Double/Brown
Dimensions W x D x H(mm) 580 x 575 x 555
Design As per Buyer's
Description of Origin Yes
Drop Test Natural Dropping At 1 Corner / 3 Edges /
6 Surfaces
Height (cm) 46
Container Stuffing 320 Sets/40' container
G-17 Cabinet Material Cabinet Cabinet Front PS 94V0 DECABROM
Cabinet Rear PS 94V0 DECABROM
PCB Non-Halogen Demand No
Eyelet Demand Yes

A3-5
 DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF ANODE CAP 3. After one side is removed, pull in the opposite direction to
remove the other.
Read the following NOTED items before starting work.
NOTE
* After turning the power off there might still be a potential
voltage that is very dangerous. When removing the Take care not to damage the Rubber Cap.
Anode Cap, make sure to discharge the Anode Cap's INSTALLATION
potential voltage.
1. Clean the spot where the cap was located with a small
* Do not use pliers to loosen or tighten the Anode Cap
amount of alcohol. (Refer to Fig. 1-3.)
terminal, this may cause the spring to be damaged.
REMOVAL
1. Follow the steps as follows to discharge the Anode Cap. Location of Anode Cap
(Refer to Fig. 1-1.)
Connect one end of an Alligator Clip to the metal part of a
flat-blade screwdriver and the other end to ground.
While holding the plastic part of the insulated Screwdriver,
touch the support of the Anode with the tip of the
Screwdriver.
A cracking noise will be heard as the voltage is discharged.

Fig. 1-3

GND on the CRT NOTE

Confirm that there is no dirt, dust, etc. at the spot where
the cap was located.
2. Arrange the wire of the Anode Cap and make sure the
wire is not twisted.
3. Turn over the Rubber Cap. (Refer to Fig. 1-4.)

Screwdriver CRT
Support
Alligator Clip
Fig. 1-4
GND on the CRT Fig. 1-1
4. Insert one end of the Anode Support into the anode button,
2. Flip up the sides of the Rubber Cap in the direction of the then the other as shown in Fig. 1-5.
arrow and remove one side of the support.
(Refer to Fig. 1-2.)

Rubber Cap

Support
CRT
Fig. 1-5
CRT
Support 5. Confirm that the Support is securely connected.
Fig. 1-2
6. Put on the Rubber Cap without moving any parts.

B1-1
 DISASSEMBLY INSTRUCTIONS
2. REMOVAL AND INSTALLATION OF 3. When IC starts moving back and forth easily after
desoldering completely, pickup the corner of the IC using a
FLAT PACKAGE IC tweezers and remove the IC by moving with the IC
desoldering machine. (Refer to Fig. 2-3.)
REMOVAL
NOTE
1. Put the Masking Tape (cotton tape) around the Flat
Some ICs on the PCB are affixed with glue, so be
Package IC to protect other parts from any damage. careful not to break or damage the foil of each IC leads
(Refer to Fig. 2-1.) or solder lands under the IC when removing it.
NOTE
Masking is carried out on all the parts located within 10 Blower type IC
mm distance from IC leads. desoldering
machine

Masking Tape IC
(Cotton Tape)

Tweezers

Fig. 2-1
IC
Fig. 2-3
2. Heat the IC leads using a blower type IC desoldering
machine. (Refer to Fig. 2-2.)
4. Peel off the Masking Tape.
NOTE
Do not add the rotating and the back and forth 5. Absorb the solder left on the pattern using the Braided
directions force on the IC, until IC can move back and Shield Wire. (Refer to Fig. 2-4.)
forth easily after desoldering the IC leads completely. NOTE
Do not move the Braided Shield Wire in the vertical
direction towards the IC pattern.
Blower type IC
desoldering machine

Braided Shield Wire

Soldering Iron

IC
IC pattern
Fig. 2-2 Fig. 2-4

B2-1
 DISASSEMBLY INSTRUCTIONS
INSTALLATION 4. When bridge-soldering between terminals and/or the
soldering amount are not enough, resolder using a Thin-tip
1. Take care of the polarity of new IC and then install the new Soldering Iron. (Refer to Fig. 2-8.)
IC fitting on the printed circuit pattern. Then solder each
lead on the diagonal positions of IC temporarily.
(Refer to Fig. 2-5.)
Thin-tip Soldering Iron IC

Soldering Iron

Fig. 2-8

5. Finally, confirm the soldering status on four sides of the IC

Solder temporarily Solder temporarily
using a magnifying glass.
Confirm that no abnormality is found on the soldering
Fig. 2-5 position and installation position of the parts around the IC.
If some abnormality is found, correct by resoldering.
2. Supply the solder from the upper position of IC leads NOTE
sliding to the lower position of the IC leads.
When the IC leads are bent during soldering and/or
(Refer to Fig. 2-6.)
repairing, do not repair the bending of leads. If the
bending of leads are repaired, the pattern may be
damaged. So, be always sure to replace the IC in this
case.

Solder Soldering Iron

IC Supply soldering
from upper position
to lower position

Fig. 2-6

3. Absorb the solder left on the lead using the Braided Shield
Wire. (Refer to Fig. 2-7.)
NOTE
Do not absorb the solder to excess.

Soldering Iron
IC

Braided Shield Wire

Fig. 2-7

B2-2
 SERVICE MODE LIST
This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily.
To enter the Service Mode, press both set key and remote control key for more than 1 second.

Set Key Remocon Key Operations

VOL. (-) MIN 0 Releasing of V-CHIP PASSWORD and LOCK PASSWORD.
Initialization of the factory.
NOTE: Do not use this for the normal servicing.
VOL. (-) MIN 1
If you set a factory initialization, the memories are reset such as the channel setting,
and the POWER ON total hours.
POWER ON total hours is displayed on the screen.
Refer to the "CONFIRMATION OF HOURS USED".
VOL. (-) MIN 6
Can be checked of the INITIAL DATA of MEMORY IC.
Refer to the "WHEN REPLACING EEPROM (MEMORY) IC".
Writing of EEPROM initial data.
VOL. (-) MIN 8
NOTE: Do not use this for the normal servicing.
Display of the Adjustment MENU on the screen.
VOL. (-) MIN 9
Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment).

CONFIRMATION OF HOURS USED

POWER ON total hours can be checked on the screen. Total hours are displayed in 16 system of notation.
NOTE: If you set a factory initialization, the total hours is reset to "0".
1. Set the VOLUME to minimum. ADDRESS DATA

2. Press both VOL. DOWN button on the set and Channel

button (6) on the remote control for more than 1 second.
3. After the confirmation of using hours, turn off the power. INIT 00 50 Initial setting content of MEMORY IC.
CRT ON 0010 POWER ON total hours.
= (16 x 16 x 16 x thousands digit value)
+ (16 x 16 x hundreds digit value)
+ (16 x tens digit value)
FIG. 1 + (ones digit value)

WHEN REPLACING EEPROM (MEMORY) IC

If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to
ensure correct data settings while making reference to TABLE 1.
NOTE: No need setting for after INI 0F due to the adjustment value.

INI +0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +A +B +C +D +E +F
00 50 04 4A 4C 07 B3 24 69 09 00 AA 10 90 4F 00 02

Table 1
1. Enter DATA SET mode by setting VOLUME to minimum.
2. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 1 second.
ADDRESS and DATA should appear as FIG 1.
3. ADDRESS is now selected and should "blink". Using the SET +/- button on the remote, step through the ADDRESS until
required ADDRESS to be changed is reached.
4. Press ENTER to select DATA. When DATA is selected, it will "blink".
5. Again, step through the DATA using SET +/- button until required DATA value has been selected.
6. Pressing ENTER will take you back to ADDRESS for further selection if necessary.
7. Repeat steps 3 to 6 until all data has been checked.
8. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.
After the data input, set to the initializing of shipping.
9. Turn POWER on.
10. Press both VOL. DOWN button on the set and Channel button (1) on the remote control for more than 1 second.
11. After the finishing of the initializing of shipping, the unit will turn off automatically.
The unit will now have the correct DATA for the new MEMORY IC.

C-1
 ELECTRICAL ADJUSTMENTS
1. ADJUSTMENT PROCEDURE 2. BASIC ADJUSTMENTS
Read and perform these adjustments when repairing the
circuits or replacing electrical parts or PCB assemblies. 2-1: CONSTANT VOLTAGE

CAUTION 1. Set condition is AV MODE without signal.

• Use an isolation transformer when performing any service 2. Connect the digital voltmeter to the TP402.
on this chassis. 3. Adjust the VR502 until the digital voltmeter is 117 ± 1V.
• Before removing the anode cap, discharge electricity
2-2: CUT OFF
because it contains high voltage.
• When removing a PCB or related component, after 1. Adjust the unit to the following settings.
unfastening or changing a wire, be sure to put the wire R.DRIVE=10, G.DRIVE=10, R.BIAS=64, G.BIAS=64,
back in its original position. B.BIAS=64, BRI CENT=130, CONT MAX=80.
• When you exchange IC and Transistor for a heat sink, 2. Place the set with Aging Test for more than 15 minutes.
apply the silicon grease on the contact section of the heat 3. Activate the adjustment mode display of Fig. 1-1 and
sink. Before applying new silicon grease, remove all the press the channel button (01) on the remote control to
old silicon grease. (Old grease may cause damages to the select "CUT OFF".
IC and Transistor.) 4. Adjust the Screen Volume until a dim raster is obtained.
Prepare the following measurement tools for electrical
adjustments. 2-3: WHITE BALANCE

1. Oscilloscope NOTE: Adjust after performing CUT OFF adjustment.

2. Digital Voltmeter 1. Place the set with Aging Test for more than 10 minutes.
3. Pattern Generator 2. Receive the gray scale pattern from the Pattern Generator.
On-Screen Display Adjustment 3. Using the remote control, set the brightness and contrast
to normal position.
1. In the condition of NO indication on the screen. 4. Activate the adjustment mode display of Fig. 1-1 and
Press the VOL. DOWN button on the set and the Channel press the channel button (10) on the remote control to
button (9) on the remote control for more than 1 second to select “R. BIAS”.
appear the adjustment mode on the screen as shown in 5. Press the CH. UP/DOWN button on the remote control to
Fig. 1-1. select the “R. BIAS”, “G. BIAS”, “B. BIAS”, “R. DRIVE” or
“B. DRIVE”.
6. Adjust the VOL. UP/DOWN button on the remote control
TV
to whiten the R. BIAS, G. BIAS, B. BIAS, R. DRIVE, and
B. DRIVE at each step tone sections equally.
7. Perform the above adjustments 5 and 6 until the white
color is looked like a white.

00 OSD 17 2-4: FOCUS

Fig. 1-1 1. Receive the monoscope pattern.
2. Turn the Focus Volume fully counterclockwise once.
3. Use the Channel UP/DOWN button or Channel button 3. Adjust the Focus Volume until picture is distinct.
(0-9) on the remote control to select the options shown
in Fig. 1-2. 2-5: HORIZONTAL PHASE
4. Press the MENU button on the remote control to end the
1. Receive the monoscope pattern.
adjustments.
2. Using the remote control, set the brightness and contrast
to normal position.
NO. FUNCTION NO. FUNCTION 3. Activate the adjustment mode display of Fig. 1-1 and
00 OSD H 17 CONTRAST MAX
01 CUT OFF 18 CONTRAST MIN press the channel button (05) on the remote control to
04 H.VCO 19 COLOR CENT select “H. PHAS”.
05 H.PHAS 20 COLOR MAX
06 V.SIZE 21 COLOR MIN 4. Press the VOL. UP/DOWN button on the remote control
07 V.SHIFT 22 TINT until the SHIFT quantity of the OVER SCAN on right and
08 R.DRIVE 23 SHARPNESS
09 B.DRIVE 24 FM LEVEL left becomes minimum.
10 R.BIAS 25 LEVEL
11 G.BIAS 26 SEPARATION 1
12 B.BIAS 27 SEPARATION 2
13 BRIGHT CENT 28 TEST MONO
14 BRIGHT MAX 29 TEST STEREO
15 BRIGHT MIN 30 X-RAY TEST
16 CONTRAST CENT
Fig. 1-2

D-1
 ELECTRICAL ADJUSTMENTS
2-6: VERTICAL SHIFT 2-10: BRIGHTNESS
1. Receive the monoscope pattern. 1. Activate the adjustment mode display of Fig. 1-1 and
2. Using the remote control, set the brightness and contrast press the channel button (13) on the remote control to
to normal position. select "BRI CENT".
3. Check if the step No. of V. SHIFT is "02". 2. Press the VOL. UP/DOWN button on the remote
4. Adjust the VR401 until the horizontal line becomes fit to control until the brightness step No. becomes “130”.
the notch of the shadow mask. 3. Receive a broadcast and check if the picture is normal.
4. Press the TV/VIDEO button on the remote control to set
2-7: VERTICAL SIZE to the AV mode. Then perform the above adjustments
1. Receive the monoscope pattern. 1~3.
2. Using the remote control, set the brightness and contrast
2-11: SUB CONTRAST
to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and 1. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (06) on the remote control to press the channel button (17) on the remote control to
select “V. SIZE”. select “CONT. MAX”.
4. Press the VOL. UP/DOWN button on the remote control 2. Press the VOL. UP/DOWN button on the remote control
until the SHIFT quantity of the OVER SCAN on upside and until the contrast step No. becomes “80”.
downside becomes 10 ± 2%. 3. Receive a broadcast and check if the picture is normal.
4. Press the TV/VIDEO button on the remote control to set
2-8: VERTICAL LINEARITY to the AV mode. Then perform the above adjustments
1~3.
NOTE: Adjust after performing adjustments in section 2-7.
After the adjustment of Vertical Linearity, reconfirm
2-12: SUB TINT/SUB COLOR
the Vertical Shift and Vertical Size adjustments.
1. Receive the color bar pattern.
1. Receive the monoscope pattern.
2. Connect the oscilloscope to TP024.
2. Using the remote control, set the brightness and contrast
3. Activate the adjustment mode display of Fig. 1-1 and
to normal position.
press the channel button (22) on the remote control to
3. Adjust the VR402 until the SHIFT quantity of the OVER
select "TINT".
SCAN on upside and downside becomes minimum.
4. Press the VOL. UP/DOWN button on the remote control
2-9: OSD HORIZONTAL until the section "A" becomes as straight line
(Refer to Fig. 2-2)
1. Activate the adjustment mode display of Fig. 1-1. 5. Connect the oscilloscope to TP022.
2. Press the VOL. UP/DOWN button on the remote control 6. Activate the adjustment mode display of Fig. 1-1 and
until the difference of A and B becomes minimum. press the channel button (19) on the remote control to
(Refer to Fig. 2-1) select "COL.CENT".
7. Adjust the VOLTS RANGE VARIABLE knob of the
oscilloscope until the range between white 100% and
TV 0% is set to 4 scales
8. Press the VOL. UP/DOWN button on the remote control
until the red color level is adjusted to 110% of the white
level. (Refer to Fig. 2-3)
9. Receive the color bar pattern. (Audio Video Input)
10. Press the TV/VIDEO button on the remote control to set
00 OSD 17 to the AV mode. Then perform the above adjustments
2~8.

A B Fig. 2-1

D-2
 ELECTRICAL ADJUSTMENTS

"A" "A"

Fig. 2-2

White 100% Red 110%

Fig. 2-3

2-13: Confirmation of Fixed Value (Step No.)

Please check if the fixed values of the each adjustment
items are set correctly referring below. (RF/AV)
NO. FUNCTION STEP NO.
04 H VCO 04
14 BRIGHT MAX 170
15 BRIGHT MIN 60
16 CONT CENT 40
18 CONT MIN 20
20 COLOR MAX 70
21 COLOR MIN 00
23 SHARPNESS 43
24 FM LEVEL 00
28 TEST MONO 00
29 TEST STERIO 00

D-3
 ELECTRICAL ADJUSTMENTS
3. PURITY AND CONVERGENCE 3-3: STATIC CONVERGENCE
ADJUSTMENTS NOTE
NOTE Adjust after performing adjustments in section 3-2.
1. Turn the unit on and let it warm up for at least 30 1. Receive the crosshatch pattern from the color bar
minutes before performing the following adjustments. generator.
2. Place the CRT surface facing east or west to reduce the 2. Combine red and blue of the 3 color crosshatch
terrestrial magnetism. pattern on the center of the screen by adjusting the pair
3. Turn ON the unit and demagnetize with a Degauss Coil. of 4 pole magnets.
3. Combine red/blue (magenta) and green by adjusting the
3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT) pair of 6 pole magnets.
1. Tighten the screw for the magnet. Refer to the adjusted
3-4: DYNAMIC CONVERGENCE
CRT for the position. (Refer to Fig. 3-1)
If the deflection yoke and magnet are in one body, NOTE
untighten the screw for the body. Adjust after performing adjustments in section 3-3.
2. Receive the green raster pattern from the color bar
generator. 1. Adjust the differences around the screen by moving the
3. Slide the deflection yoke until it touches the funnel side deflection yoke upward/downward and right/left.
of the CRT. (Refer to Fig. 3-2-a)
4. Adjust center of screen to green, with red and blue on 2. Insert three wedges between the deflection yoke and
the sides, using the pair of purity magnets. CRT funnel to fix the deflection yoke.
5. Switch the color bar generator from the green raster (Refer to Fig. 3-2-b)
pattern to the crosshatch pattern. RGB RGB
6. Combine red and blue of the 3 color crosshatch
pattern on the center of the screen by adjusting the pair
of 4 pole magnets. R
7. Combine red/blue (magenta) and green by adjusting the G
pair of 6 pole magnets. B R
8. Adjust the crosshatch pattern to change to white by
G
repeating steps 6 and 7.
B
UPWARD/DOWNWARD SLANT RIGHT/LEFT SLANT
3-2: PURITY
NOTE Fig. 3-2-a

Adjust after performing adjustments in section 3-1.

1. Receive the green raster pattern from color bar generator.
2. Adjust the pair of purity magnets to center the color on
the screen.
Adjust the pair of purity magnets so the color at the ends WEDGE WEDGE
are equally wide.
3. Move the deflection yoke backward (to neck side)
slowly, and stop it at the position when the whole screen
is green.
4. Confirm red and blue color.
5. Adjust the slant of the deflection yoke while watching the WEDGE
screen, then tighten the fixing screw.
DEFLECTION YOKE WEDGE POSITION
DEFLECTION YOKE SCREW Fig. 3-2-b
MAGNET SCREW

PURITY MAGNETS
6 POLE MAGNETS
4 POLE MAGNETS
Fig. 3-1

D-4
 ELECTRICAL ADJUSTMENTS
4. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION)

CRT PCB
TP024
CP806
TP022

J801

CP801 CP802B CP803B

1
80
CD
CRT

CP803A

CP601
VR401
FB401
VR402

CRT DY
TP402
TU001

CP401 CP1001
VR502

SPEAKER

L503 CP502
DEGAUSS COIL
CP802A

AC IN S501A S501B

J710 J711

MAIN PCB

D-5
 BLOCK DIAGRAM

TU001

10 11 12 13 17

CH. DOWN
IC1001 AN7511
VOL. DOWN MICON/CHROM IC
IC101 OEC7091A 2 6 SPEAKER
21 20 34
SOUND AMP SP1001
CH. UP
4 IC 8
66 ATT
VOL. UP RGB Proc.2
73 OSD SW Q804
67 CONTRAST BRIGHTNESS 50 RED AMP
POWER RGB OUTPUT Stage
Chroma Proc.
68 DRIVE 51
ACC/C-BPF Q805
I/O CUT OFF
69 APC/KILLER 52
OS101 IIC HV BLK GREEN AMP
70 RGB Proc.1 MCU TINT/DEMO
TIM
1 RGB MATRIX CLK Q607
74 INT
COLOR CONT Q806
PWM H-CTL
78 BLUE AMP
AD
Ver.Proc.
OSD Hor.Proc.
Ver SYNC SEP 46
SYNC SEPA/Hor. VCO
Ver.COUNT DOWN Hor.COUNT DOWN 45
ROM V RAMP AFC-1/H COINCIDENT
RAM AFC-2 H PHASE
Q402
J711 H. DRIVE

2 Q401
VCXO H. OUTPUT
J710
2
56 58 57 27 26 37 38 16 11 6 8
X601 B G R
CRT
3.579545MHz Heater
V-OUT IC 10 F 9
IC501 IC401 AN5522
T501 LTV-817M-VB Q507 5 6 MEMORY IC
FEED BACK PUMP UP
11 3 FEED BACK SW SDA SCL IC199
S-24C04BDP-LA -
AMP
7 Q502 +
DEGAUSS COIL
BUFFER VCC
13 L503
7 1 2 6 5 DY
5
Q501 D501~D504
SWITCHING RECTIFIER FB401

9
Q503 1 F
PROTECT DRV. 2 S
L501 10 HV
2 4
3
1 3

F501

AC IN

E-1 E-2
 PRINTED CIRCUIT BOARDS
MAIN/CRT (INSERTED PARTS)
SOLDER SIDE

SW105 SW102 SW101 SW104 SW103

D106 J710

OS101 W012
J711

C123

W013

C701
6.3A125COR250V

W011
W053

W049
W050
FH501 FH502

W135
F501

W052

R603

D702
R101
W051
TP024

R605
W876

W048
C505

R802

R804

W010
S501B
CD501
05 J801
R8 CP806_1 29 Q603

W874
R6 W009

W045
S501A
Q602

R608
TP022 Q606 D604

W102
Q607 W825

W007
03

C620
R8

R606

D603
W875

TH501
C624

C630
R500 TP023 Q610
7

C621
R80

W005
W003
CP802A

R618
W002

R615
W117
R806

R614
Q805

R613
Q806 Q804 CD802A
C530_1 W001
L501_2

C617
W018

C623
C628
R620
W111

C622
Q609

W065
R611

W802
W017

W873
W064

W872
W811

W871

C614
W808

W889
C8
C506 02

CP502
W817

C633

C612
IC199
D805
RY501

D806

W061
W015

D804
W118 R819 W062
D501

W846

C610
W123
C533_1

W858

W884
CP802B Q504 R515

W119
CD803B

C616
CP803B 01 R143

R107

R108
8

C118
CD802B
CP W836

R602
R520

C601
W812 X601
W141

C615
C605
W059
D502

W122 W058 R123

C502
C503

C103
W057

C606_1
W860
D504

W127

R115

C106
W056
R501

C501_1

C602
W107
D503

R104
W055
W054 W128

W104
W809
Q601

W106

R125
W113 Q105
C507

C520
R511 R401
R502

W086
W083

R127
R503 R528 W081 W023
D515

R1002
C509 W866
W020
B501 R517 W080 W845
B503 W079

D402
C514_1

C516 W078

C1009
D519
C511

R516 Q402_1 W077

W125

D521 R529 W076 W837

Q502 W075 CP1001_1

C1006
D514
R543

D527 W074

R446
W124
W888 R542 D520 W071 W019

C439
C446
D508 Q501
T501_1

D517

W842
R002 W070

R450
D509 C531
B504 R001
C440

W829
C508

C418
C521 D406 W093

R1015
W805
R504_1

R1001
IC1001_1

C1001_1
T401_1
D51
D523

Q503
D506

W027
D412 D606
R403
HS501 C5

R553

R523
17
_1 R512

C414
D524 W096
C518_1

VR502

R514 R554 W892 W816

W120

CP402

R525
W853

R524
IC501
R417
D419
HS401 IC401

HS403
W830

R420
R418
W850
D528
W893

R427

Q507

C443 Q401 D418

W844
R432
D526

R410
R436

W849
FB401
L401

CP401

W114

W090
W091
W088
R434
C402_1 W087
R406 VR402 D001

C417
C403
C437_1 W101
R402 C004
R413
TP402 W115 W100

TU001
C427

R408

D404
V.POSI
R445

VR401 R411
D407

C002
W899
R412
C448

R424
R409

D410
C420

C433

W121
D411

R421 R429
C434

W142
CD803A

W130
CP601

D405 CP803A
R433

R422
W815
C407_1

F-1 F-2
F-3
R624
R601

C603
R1005
C604

R734
R120

C609
C113

R121_1

R604
R103 C107

25
C104 R102 C1002
C108_1 C105
R607 C102

41
IC
10

R1003
1
C626

1
C627
R111

R627
64

C629
R610 R609
C003

R129

C001
R113 R133

R621
R628 R110
R105
R003
R004

R616

R106

R617
C101
R109
R437

R404

R506
SOLDER SIDE
PRINTED CIRCUIT BOARDS

R128
R814
MAIN/CRT (CHIP MOUNTED PARTS)

R816
C810
R126
W879

R813
R809
W833 B_SHORT

C811

R811 R815
W880
C809

R534

R532
R505

C513
C522
R507

R513
R533
C519

C512

F-4
 A B C D E F G H

MICON/CHROMA/TUNER SCHEMATIC DIAGRAM

(MAIN PCB)
8 8

10 KANP
0 0 0 0
1 2 3 4

C633
VSS
E1

E2
E0
S-24C04BDP-LA
0 H.CTL ACCESSORY

MEMORY IC
SW W858 Q607
4.9

16V
Q609

IC199
R621 KTC3198
KTC3198

MODE
6.0 5.0

R617

68K
0 220

1/4W
VCC

SDA
SCL
BT001

R628
5.6

R620
R03(AB)E_2P_G

1K
8 7 6 5

W889
1K
4.9 0 5.0 5.0 R618

CLAMP_OFF
BT002

P.CON+5V
P.CON+5V
PROTECT
TM101
8.2K 1/4W R03(AB)E_2P_G

H_OUT
RC-EH020

H_CTL
FROM/TO DEFLECTION/CRT

3
DEGAUSS_H

H_SYNC
R608

ABCL
PROTECT
H_CTL

G.OUT

R.OUT
7 7

B.OUT
C118 CLAMP
1K 1/4W
CLAMP_OFF

2
11E1-EIC
6.3V 100 KA C101
R110 10K V_OUT

100 1/4W
0.01 F R109 10K

100 1/4W

100 1/4W
GND

63V 1 MKT
R610

5.6K
C630 V_FEEDBACK

0.01 F
AT+5V

W846

D606
W884
ABCL

0.01
16V 100 KA

3.3K
H_OUT

R105

10K 1/4W
R611
R615

R614

R613
X-RAY

50V 1 KA
R616

R609
R108 100 1/4W C629

120K

C628
3.9K

C627

C626

C624
1 CNVSS 41 NC SDA
R.OUT
2 XIN 42 HVCO F/B SCL R107 100 1/4W 0.01 F
UNREG+12V G.OUT

R627
5

10K
3 XOUT 43 AFC FILTER C623

R106
NC B.OUT

R133

3.3K
22K
0 NC NC
4 TEST1 44 DEF GND 0 0 2.0 0 0 5.0 4.2 5.0 0.0 4.9 3.8 5.0 5.0 5.0 8.3 0 8.3 2.0 6.6 0 3.5 3.7 0
H_SYNC
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 16V 100 YK

7.9
6 5 VSS 45 FBP IN
8V REG 6

8.5
0 8.7 R607
6 MCU VCC 46 H OUT Q606 FROM/TO TV POWER

65

40
KTC3203_Y
7 TEST0 47 DEF VCC 4.8 100
0

11.3
AFT MCU GND REMOTE+12V

66

39
8 FILT 48 NC R129
Ver.Proc. 4
9 HLT 49 HI VCC 2.4 IIC BUS Hor.Proc. 4.4 POWER_FAIL
2.2K KEY1 PGB OUTPUT Stage Ver SYNC SEP V_OUT

67

38
10 VHOLD 50 R OUT R113 DECODER DRIVE SYNC SEPA/Hor.VCO UNREG+12V
Ver.COUNT DOWN
4.9 CUT-OFF Hor.COUNT DOWN 2.5 R606
11 CVIN 51 G OUT 2.2K KEY2 SDA/SCL AFC-1/H COINCIDENT V RAMP V_FEEDBACK X-RAY

68

37
R123 ROM HV BLK
12 RESET IN 52 B OUT RAM OSD AFC-2 H PHASE 27K 1/4W DEGAUSS_H
4.9 0
2.2K 1/4W R115 POWER_ON GND

69

36
13 MCU RESET OUT 53 ACL
2.8 C622 TU+BT
14 Y SW OUT 54 NC 4.8
22K 1/4W REMOCON

70

35
P.CON+5V
15 V/C GND 55 PROTECT
I/O 3.5 50V 1 KA C621
4.8
16 3.58 XTAL 56 SDA AUDIO_OUT

71

34
NC RGB Proc.2
17 C-APC 57 H_CTL 16V 47 YK
5 4.8 OSD SW RGB Proc.1 0.7 1 FROM AV 5
72 RGB MATRIX C620

33
18 MCU5.7V REG OUT 58 SCL NC CONTRAST NC
P-ON CONT Power Manage. BRIGHTNESS COLOR CONT 3.0
19 NC 59 NC 4.9 IIC 0.01 F VIDEO_IN
AUDIO_MUTE D603 D604
73

32
MCU RESET NC
20 CVBS IN3 60 NC
2.0 TIM 9.0 R605 MONO_F_A_IN
21 AUDIO IN3 61 NC X-RAY 1SS133 MTZJ8.2B
R125 CCD
74

31
INT Vldeo Proc. Chroma Proc. GND
22 V/C VCC 62 DEGAUSS_H 4.9 2.9 P.CON+5V 180 1/2W
47K 1/4W IIC_OFF R127 C-TRAP/YDELAY ACC/C-BPF
75

30
23 MCU TEST 63 STANDBY_H PWM APC/KILLER NC TUNER+5V
SHARPNESS
1K 1/4W CLK CONT TINT/DEMO 2.6
24 CVBS IN2 64 VOLUME 0 AD MCU BLACK STRETCH 5V REG
ON_TIMER CPU core
76

29
CLK Y MUTE NC Q602 REMOTE+12V
25 AUDIO IN2 65 NC 4.9
0 5.6 R604 KTC3203_Y
26 CVBS IN1 66 AFT
77

28
NC LPF
27 AUDIO IN1 67 KEY1 6bB AMP ATT 100 5.5
4.6 2.2 C614 7.2 R629
POWER_FAIL MONO_F_A_IN
78

27
28 5.7V REG OUT 68 KEY2 C617
VCO 1.9 50V 1 KA C612
29 C(Y/C) IN 69 POWER_ON R111 0 XO 12 2W
VIDEO_IN 7.2
4 4
79

26
10V 100 YK
30 Y(Y/C) IN 70 REMOCON 5.5
47K VCXO 50V 1 KA
4.9 2.2 STEREO+5V
31 VREG VCC 71 AV2 R624 5V REG
80

25

19

18
NC NC 4.9
Q603 C001
32 FSC OUT 72 AV1 1 NC W815
MICON/CHROMA IC 75 KTC3203_Y
33 MONITOR OUT 73 AUDIO_MUTE IC101 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 C002 0.022 F
OEC7091A 0 0 4.9 4.9 0 4.9 0 1.1 3.0 0.8 3.4 4.8 4.8 3.4 0 3.3 2.8 5.5 0.0 0 0 4.9 0 1.9 2 NC
34 AUDIO ATT OUT 74 X-RAY
0.01 F

NC

22P CH 100CT3R505
3.579545MHz
NC NC
50V 1 KA
C104

7.2 6.3V 1000 YK

50V 1 KA
35 AUDIO ATT FILTER 75 IIC_OFF TUNER+5V
5.5 3

X601
C601

100 1/4W
C102
R120
36 TEST3 76 ON_TIMER AT+5V
470
C106

R602
5V REG TO SOUND
5.0 4 NC
R102

37 V RAMP F/B 77 BBE 0.01 F

1K

0.001 B

Q610
560P W
C108_1

38 V RAMP OUT 78 POWER FAIL KTC3203_Y

C113

C603
C602

0.1 F
470P B

5 NC
10V 220 YK

AUDIO_OUT
1K

39 V RAMP CAP 79 X-RAY_TEST

R103

C609
220P B
C103

40 8.7V REG OUT 80 EXT_MUTE 6 NC

0.022 B
GND
W809

1/4W

C604
0.01 F
R104

1M
C107

10V 470 YK
C105

AUDIO_MUTE

C606_1
3 C610
C616 3

8.2K 50V 1 KA
TU_AUDIO
STEREO+5V
4.9 7 NC

C605
6.3V 47 KA 50V 1 KA
W816

0 ON_TIMER TEST POINT

SWITCHING C615 8 NC
TU_VIDEO
4.8 Q105
R601

KRA102MAT 50V 1 KA CP601 173979-7

9 NC
R004 NC 7
SCL
POWER_ON

10
REMOCON

NC 6
KEY1
KEY2

100
AT+5V

R003 GND 5
11 SDA
IIC_OFF IIC_OFF
100 4
AFT SDA SDA
12 3
5.5 SCL
R143 SCL 2
TU_AUDIO
R121_1

4.9 8.8 R603 13 GND 1

270

47 1/4W R001
2 2
16V 10 KA

R128 120 1/4W W844

14 NC 68K 1/2W
C123

560 5V REG
R126 R101 R002
Q601 TU+BT
15
POWER ON/ON TIMER

KTC3203_Y
2.7K 560 1/4W 68K 1/2W

0.022 B
0.022 F
SLR-342VCT32

C003
C004
16 NC
TU001
VOL DOWN
4.9

4.8

EVQ21505R

EVQ21505R

EVQ21505R

EVQ21505R
D106

CH DOWN

EVQ21505R

POWER
VOL UP

ENG36A01G TU_VIDEO
SW101

SW103

SW104

SW105
CH UP

SW102

17

MTZJ33B
B+ 3
GND 2
1

W830

D001
Vout

20

21
PCB010
TMC563

OS101
RPM7138-H5
CAUTION: DIGITAL TRANSISTOR LUMINANCE SIGNAL R.SIGNAL
1 1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED CAUTION:SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
ARE
ATTENTION:LES PIECES REPAREES PAR UN ETANT DEFLECTION SIGNAL G.SIGNAL
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST DANGEREUSES AN POINT DE VUE SECURITE B.SIGNAL
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES AUDIO SIGNAL
DANS LA NOMENCLATURE DES PIECES TUNER VIDEO SIGNAL

A B C D E F G H
G-1 G-2
 A B C D E F G H

DEFLECTION/CRT SCHEMATIC DIAGRAM (MAIN PCB)

FROM/TO MICON/CHROMA/TUNER CP802A B2013H02-6P CP802B B2013H02-6P
CLAMP CLAMP
CLAMP CLAMP 1 1 CLAMP
8 CLAMP_OFF CLAMP_OFF 8
CLAMP_OFF CLAMP_OFF 2 2 CLAMP_OFF
GND GND
GND 3 3 GND
G.OUT G.OUT
G.OUT G.OUT 4 4 G.OUT
R.OUT R.OUT
R.OUT R.OUT 5 5 R.OUT
B.OUT B.OUT
B.OUT B.OUT 6 6 B.OUT

1/2W
V_FEEDBACK V-OUT IC IC401 AN5522 CP803B B2013H02-4P
CP803A B2013H02-4P

R819
V_OUT HEATER HEATER
THERMAL HEATER 1 1 HEATER
GND

10
ABCL PROTECTION GND 2 2 GND
PUMP
H_SYNC UP NC 3 3 NC
+ AMP 180V 180V
H_OUT - 180V 4 4 180V
CD801
VCC GND
GND SM1098-009-1A CP801
7 8 1 2 3 4 5 6 7 A2361WV2-2P 7
X-RAY

1SS133
1 1

1SS133

1SS133
3.7 25.4 1.3 0 12.8 25.8 3.7

D805

R814
D804

D806
R809

R811
3.9K

3.9K
R437

3.9K
2 2

1K 1/4W
R403
4.7K

W871

W872

W873
35V 100 YK
12

11E1-EIC
D412

C414
V801
A51AEZ90X24

13 5 7 1
11

W879
W833

390P CH W880
B

1/2W

1K 1/2W
680 1/2W
6

MTZJ30B
G

W802
R432

R410

R411

W808
D418
8

W811
R

330P CH
390P CH
10

R816

R815
680
R418 R420

R813

C810

470
C811

C809
470

470
9

25V 1000 YK

470 1/2W
39K+-1% 15K +-1%

W849

C418
6 6

R412
100V 0.22 MMTS
130.6 130.6 130.6
HS403 5.9 5.9 5.9

47K METAL
22K +-1%

50V 10 YK
763WSAA013

R417

C427
VR402

C403
50V 3.3 YK V.LIN.
6.3 6.3 6.3

METAL 1K
V.POSI.
VR401

MTZJ30B
RED AMP GREEN AMP BLUE AMP

D419
Q804 Q805 Q806
W850

W853

KTC4217 KTC4217 KTC4217

C417

1/2W

470 1/2W
1 1/2W
2.2 1/2W

2.2 1/2W

R433
R413
R434

R436

R406

1.8K

TP024
TP023
TP022
4.7K +-1%
MTZJ5.1B

W899
R408

14 15 16

100V 22 YK
D404

C434

2.7K 1/4W
2.7K 1/4W

W876
W874
5 5

W875

R804
R424 R409

R802

2.7K 1/4W
D411

R806
12K 2W
18K +-1% 15K +-1% 1N4937

12K 2W
R803

12K 2W

R805
R807
CP401
A1561WV2-A5P
L401 5
T401_1 4
ECWF
ELH5L4113 C433
9 ETH09K14BZ 3
C439
C437_1

35V 470 YK
100V 0.01 MMTS

3 4 R402 NC 2
250V 0.33

500V 22P SL 2 1
10
1K 1W
C440

1 6
R429
HS401
MPP

4 11 C402_1 4
763WSAA013 1.8 2W
FROM/TO SOUND H.OUTPUT
2KV 0.001 RR
Q401 114.0
0.0091
470 1/2W

2SD2499
C443

GND
R446

0 CP402 FOCUS
R404

27.0
003P-2100
1K

H.DRIVE
100 1/4W

1.25KV

SCREEN CP806_1
Q402_1
R427

0
0.3 2SC1627_Y
0
MTZJ6.2B
D405

C446
100P CH
C407_1

D407
50V 22 YK
1N4937
R422

2KV 0.001 B
6.8K 1/2W
3 +B 3

C802
FB401
TP402 3221012F
289 COL
1 HV
118.1 E180
6
J801
B_SHORT
115.0 B+ ISHS53S
2
96.4 NC
46.1 AFC 6.4

11
9

10

12
HEA 0
F

9
7.3 TER
10

F
8
0 GND S 101.6 0
8

1
7
40.1 E12 GND 0

4
1N4937

99.6

5
2 NC 4 11
2
D410

63.9 E27
3 ABL 3.6
7
0 GND C420
8
C448
FROM TV POWER 22.8 E8 100V 0.1 MMTS
5
NC R421
R445 250V 22 YK PCB110
+B
68K 1/4W TCC425
150K 1/2W
GND
R401 D402 D406 R450
UNREG+12V
220 1W 11E1-B-EIC 11E1-B-EIC 180 2W PCB010
TMC563

R.SIGNAL
1 G.SIGNAL 1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. ATTENTION:LES PIECES REPAREES PAR UN ETANT
CAUTION:SINCE THESE PARTS MARKED BY ARE
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP DANGEREUSES AN POINT DE VUE SECURITE CRITICAL FOR SAFETY,USE ONES B.SIGNAL
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. N’UTILISER QUE CELLS DECRITES DESCRIBED IN PARTS LIST ONLY
IS NON POLAR ONE. DEFLECTION SIGNAL
DANS LA NOMENCLATURE DES PIECES

A B C D E F G H
G-3 G-4
 A B C D E F G H

TV POWER SCHEMATIC DIAGRAM

(MAIN PCB)
8 8

W836

W817
TO MICOM/CHROMA/TUNER

REMOTE+12V
W812
UNREG+12V

RELAY DRIVE

10K 1/4W
Q504

R515
7 KTC3198 7
0.2 TO DEFLECTION/CRT
0.6

0
GND
+B

RY501 B503 UNREG+12V

ALKS321 2 1 W5RH3.5X5X1.0

3 C516
4

1/2W

KX
+-10%

250V 0.001 KX
R500
DEGAUSS COIL 500V 0.001 B

C533_1

C530_1
TO SOUND

250V 0.001
L503

2.7M
8R200026 CP502 R517
6 A1561WV2-2P
D519 6
TH501 SOUND+B

16V 1000 YK
SB290S 3.3 3W
2 B59203-S1060-B14

C501_1
2

1SS133
D515
GND
1
1

SOUND_GND
R501 R502

1SS133
1.2M 1/4W

D526
1.2 7W 0.22 1W T501_1
FROM/TO AV

RM11C-EIC

RM11C-EIC
81291144

R503
B504

D501

D502
R524

200V 330 UP
W5RH3.5X5X1.0 D510
8 GND

C507
131.7

YXF
1.2M 1/4W
30DF6-FC 1 2W
C502 C503 7

W893
PROTECT DRIVE

R511

160V 100
9
Q503

C521
ECQUL

2KV 0.001 2KV 0.001 B

10K 1/4W
5 143.1 P1 C517_1 2SA1624 5

RM11C-EIC
R520 B

RM11C-EIC
NC 6 10

D503

MTZJ18B
NC
C506

D504
2KV 0.0018 RR

100V 4.7 YK
D509
275V 0.1

1.5M 1/2W P2

47K 1/4W
143.1

R523
C508
5 11

R525
R513

100
NC 4 12
D520 FROM/TO MICON/CHROMA/TUNER

10K 1/4W
12.1

R512
1SS133
3 13
D514

W5RH3.5X5X1.0
0
COIL,LINE FILTER 2 14 NC X-RAY
SB140-EIC

B501
L501_2
15.2
1R0A562F20
1 15
D517 R516 R528
4

POWER_FAIL

16V 1000 YK
YK
4 1N4937 100 1/4W 3.3K 1/4W 4

22K 1/4W
MTZJ5.1B
R529

C531
D527
C520
3

50V 22
SWTCHING
Q501 C518_1
STP5NC50FP GND
D R543 250V 0.0022 KX
144.0 C509
G 4.8
W842
C505 330 2W 0.047 M TU+BT

1SS133
D508
2KV 680P RR

D524

W805
S 0.1
C514_1

W892
EYF-52BC

275V 0.22 ECQUL

FH502

MTZJ3.9B DEGAUSS_H

R507

150
6.3A125V

C519
6.3A125V

22K
R506
6.3A 125V

R532

1.5K
F501

1N4937

R533

270
D523
0.01 B
D521
AC120V_60Hz R534
EYF-52BC

P.CON+5V
FH501

CD501
1SS133 R504_1

1/4W
3 0R415906 100 3

R553
BLACK S501A 1K 1/4W

270
W888

BUFFER R505

5.6K
C511
Q502

MTZJ18B
BLADE
WIDE

WHITE S501B KTC3203_Y

1
D506
25V 47 YK

1/4W
4.8 C513
0.1

R554
3

2
0.0027 B

100K
0.27 1W

0
R542

6.3
B

HS501 FEED BACK 6.0

C512

763WAA0023 IC501
0.01

FEED BACK
LTV-817M-VB 5.4
SWITCHING

VR502
+B ADJ
Q507

1K
KTC3198
6.3A 125V
2 2

MTZJ5.6B

0.033 B
D528
CAUTION:FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,

C522

1/4W
R514
REPLACE ONLY WITH THE SAME TYPE FUSE
6.3A 125V(F501).

5.6K
ATTENTION:POUR UNE PROTECTION CONTINUE LES RISQUES D’INCEIE
N’UTOLISER QUE DES FUSIBLE DE MEME TYPE CAUTION: IS THE LIVE CONNECTION
6.3A 125V(F501). PCB010
TMC563

1 1
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR.
THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME ATTENTION:LES PIECES REPAREES PAR UN ETANT CAUTION:SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
ARE
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DANGEREUSES AN POINT DE VUE SECURITE
IS NON POLAR ONE. WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. N’UTILISER QUE CELLS DECRITES DESCRIBED IN PARTS LIST ONLY
DANS LA NOMENCLATURE DES PIECES

A B C D E F G H
G-5 G-6
 A B C D E F G H

SOUND SCHEMATIC DIAGRAM

(MAIN PCB)
8 8

7 7

FROM MICON/CHROMA/TUNER

AUDIO_MUTE

FROM/TO DEFLECTION/CRT

6 GND 6

56K 1/4W
FROM/TO AV

R1015
GND
SOUND AMP IC

68K 1/4W
IC1001_1 AN7511

R1001

1
-
7

2
FROM TV POWER

5 5

+
6

3
SOUND+B
GND
W829

4
SOUND_GND

50V 10 YK

C1001_1
W866

C1006

F
R1003
FROM MICON/CHROMA/TUNER

270K

0.0015 B
1

R1005

100K
CP1001_1 CD1001_2

W837
C1002
18 TID-X02P-B2 CH12403B SPEAKER
4 GND 1 1 SP1001_2 4
810-47-171
STEREO+5V 2 2 8 OHM
AUDIO_OUT
17

R1002
W845

50V 1 KA
47K 1/4W

C1009
3 3

2 2

PCB010
TMC563

1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
CAUTION:SINCE THESE PARTS MARKED BY ARE ATTENTION:LES PIECES REPAREES PAR UN ETANT
DANGEREUSES AN POINT DE VUE SECURITE
AUDIO SIGNAL
1
CRITICAL FOR SAFETY,USE ONES
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES

A B C D E F G H
G-7 G-8
 A B C D E F G H

AV SCHEMATIC DIAGRAM
8 (MAIN PCB) 8

VIDEO IN(FRONT)
J710
HTJ-032-03AY
20
VIDEO_3_IN

3
NC
7 7

E
2

1
H
AUDIO_L IN(FRONT)
J711
HTJ-032-03AW

C701 19

3
R734

NC

E
L3_IN

1
H
16V 10 KA 1K

MTZJ6.8B
D702
6 6

FROM/TO SOUND

5 GND 5

FROM/TO TV POWER

GND

TO MICON/CHROMA/TUNER

W825
MONO_F_A_IN
4 4

GND
W860
VIDEO_IN

3 3

2 2

PCB010
TMC563

NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME AUDIO SIGNAL
1 WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE 1
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
TUNER VIDEO SIGNAL

A B C D E F G H
G-9 G-10
 WAVEFORMS
MICON/CHROMA/TUNER

1 0.5V 2ms/div 6 1V 20µs/div 11 200V 20µs/div

2 20V 20µs/div 7 1V 20µs/div 12 10V 5ms/div

DEFLECTION/CRT

3 200mV 20µs/div 8 0.5V 5ms/div 13 10V 5ms/div

4 0.5V 5ms/div 9 20V 20µs/div 14 50V 20µs/div

5 1V 20µs/div 10 2V 20µs/div 15 50V 20µs/div

NOTE: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
H-1
 WAVEFORMS

16 50V 20µs/div
SOUND

17 0.5V 1ms/div

18 1V 1ms/div
AV

19 200mV 500µs/div

20 500mV 20µs/div
NOTE: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.

H-2
 MECHANICAL EXPLODED VIEW
104
202
110

202

202 202

202

202

201

103

108 202

201 PCB110
107 (CRT PCB ASS'Y)
201

111 109

201 204

206
111
105 203
204
106

102

205 PCB010
(MAIN PCB ASS'Y)

101E
101D

101C
101E 101D

101B 203

203

101A
101

I-1
 MECHANICAL REPLACEMENT PARTS LIST
Location No. TSB P/N Reference No. Description

101 AD302337 A3M903A720 CABINET,FRONT ASSY

101A AD301497 701WPJB758 CABINET,FRONT
101B AD301498 711WPA0173 PLATE,FRONT
101C AD301499 713WPA0214 GUIDE,REMOCON
101D AD301500 735WPA0670 BUTTON,BASE
101E AD301501 735WPBA435 BUTTON,FRAME

102 BZ710039 8995034000 CORD CLIP UL CO.

103 AE000747 A3M903A740 CABINET,BACK ASSY
104 AD302339 722549A172 SHEET,RATING
105 AD300132 7230006818 SHEET,CAUTION
106 AE000007 7220001107 SHEET,HWC
107 BZ710258 741WUA0001 SPRING,EARTH
108 AE000006 7220001119 SHEET,CSA WARNING
109 BZ710260 899HV3T000 HOLDER,ANODE WIRE

110 AD302152 726000A040 SHEET,CRT NO.

111 AD301899 800WR0A003 SHEET,CRT SUPPORT

201 BZ710275 8121J50B54 SCREW,TAP TITE(P) GW20 5x28

202 BZ710035 8117540A64 SCREW,TAPPING(B0) TRUSS 4x16
203 BZ710031 8110630A04 SCREW,TAP TITE(P) BRAZIER 3x10
204 BZ710239 8109I30A04 SCREW,TAP TITE(B) WH7 3x10
205 BZ710019 8109630802 SCREW,TAP TITE(B) BRAZIER 3x8
206 BZ710018 8107630804 SCREW,TAP TITE(S) BRAZIER 3x8

--- AE000748 723000C255 SHEET,BAR CODE

--- AE000010 791WHA0085 LAMIFILM,BAG
--- AD301504 792WHA0379 PACKAGE,TOP
--- AD301505 792WHA0380 PACKAGE,BOTTOM
--- AD302340 793WCDB656 GIFT BOX
--- AD302341 A3M903A975 INSTRUCTION BOOK KIT
--- AD300436 J3I70416 IMPORTANT SAFETY INSTRUCTIONS
--- AD300022 J3I70417 REGISTRATION CARD
--- AD300023 J3I70436 ESP CARD
--- AD302342 J3M90301A INSTRUCTION BOOK
--- AD300812 JB5UD400 POLYBAG,INSTRUCTION(RED CAUTION)

J1-1
 ELECTRICAL REPLACEMENT PARTS LIST
Location No. TSB P/N Reference No. Description
RESISTORS
! R401 AD300783 R3X181221J R,METAL OXIDE 220 OHM 1W
! R402 AE000676 R3K181102J R,METAL 1K OHM 1W
! R408 AD301014 R4X5T6472F R,METAL 4.7K OHM 1/6W
! R409 AD300037 R4X5T6153F R,METAL 15K OHM 1/6W
! R424 BZ210105 R4X5T6183F R,METAL 18K OHM 1/6W
! R429 BZ210046 R6558A1R8J R,FUSE 1.8 OHM 2W
! R450 BZ210246 R3X18A181J R,METAL OXIDE 180 OHM 2W
! R500 BZ210080 R0G3K2275K RC 2.7M OHM 1/2W
! R501 AD300720 R5X2AE1R2J R,CEMENT 1.2 OHM 7W
! R502 BZ210190 R63581R22J R,FUSE 0.22 OHM 1W
! R514 BZ210166 R002T4562J RC 5.6K OHM 1/4W
! R517 BZ210111 R3X28B3R3J R,METAL 3.3 OHM 3W
! R520 BZ210206 R002T2155J RC 1.5M OHM 1/2W
! R524 BZ210083 R3X28A010J R,METAL OXIDE 1 OHM 2W
! R542 AD301143 R3X181R27J R,METAL OXIDE 0.27 OHM 1W
! R543 AD301016 R3X28A331J R,METAL OXIDE 330 OHM 2W
R629 AD301433 R3X18A120J R,METAL OXIDE 12 OHM 2W
! R803 BZ210050 R3X18A123J R,METAL OXIDE 12K OHM 2W
! R805 BZ210050 R3X18A123J R,METAL OXIDE 12K OHM 2W
! R807 BZ210050 R3X18A123J R,METAL OXIDE 12K OHM 2W
CAPACITORS
C402 BZ110202 C0PLRR713K CC 0.001 UF 2KV R
! C414 AD301434 E02LU4101M CE 100 UF 35V
C418 BZ110053 E02LF3102M CE 1000 UF 25V
! C433 BZ110149 E02LT4471M CE 470 UF 35V
! C434 BZ110195 E02LU8220M CE 22 UF 100V
! C437 BZ110026 P411F3334J CMPP 0.33 UF 250V ECWF
! C443 AD302292 P4N8FJ912H CMPP 0.0091UF 1.25KV
! C448 BZ110204 E0ELFD220M CE 22 UF 250V
! C501 AD300925 E02LT2102M CE 1000 UF 16V
C502 AD300078 C0JBB0713K CC 0.001 UF 2KV B
C503 AD300078 C0JBB0713K CC 0.001 UF 2KV B
! C505 BZ110025 P2122B224M CMP 0.22 UF 275V ECQUL
! C506 BZ110035 P2122B104M CMP 0.1 UF 275V ECQUL
! C507 AD301635 E51CGC331M CE 330 UF 200V
C514 AD301320 C0PLRR7U2K CC 680 PF 2KV R
C517 AD301702 C0PLRR7G3K CC 0.0018 UF 2KV R
! C518 AD301108 CD39E0MH3M CC 0.0022UF 250V
! C521 AD300060 E62NFB101M CE 100 UF 160V
! C530 AD301026 CD39E0M13M CC 0.001 UF 250V
! C531 AD300925 E02LT2102M CE 1000 UF 16V
! C533 AD301026 CD39E0M13M CC 0.001 UF 250V
C802 AD300078 C0JBB0713K CC 0.001 UF 2KV B
DIODES
D001 BZ410037 D97U03301B DIODE,ZENER MTZJ33B T-77
D106 BZ410054 0021721150 LED SLR-342VCT32
D402 BZ410123 D2W0011E10 DIODE,SILICON 11E1-B-EIC
! D404 BZ410020 D97U05R11B DIODE,ZENER MTZJ5.1B T-77
! D405 BZ410066 D97U06R21B DIODE,ZENER MTZJ6.2B T-77
D406 BZ410123 D2W0011E10 DIODE,SILICON 11E1-B-EIC
! D407 AD300731 D2WXN49370 DIODE,SILICON 1N4937
! D410 AD300731 D2WXN49370 DIODE,SILICON 1N4937
! D411 AD300731 D2WXN49370 DIODE,SILICON 1N4937
D412 BZ410043 D2WT011E10 DIODE,SILICON 11E1-EIC
D418 BZ410019 D97U03001B DIODE,ZENER MTZJ30B T-77
D419 BZ410019 D97U03001B DIODE,ZENER MTZJ30B T-77
! D501 BZ410062 D2WTRM11C0 DIODE,SILICON RM11C-EIC
! D502 BZ410062 D2WTRM11C0 DIODE,SILICON RM11C-EIC
! D503 BZ410062 D2WTRM11C0 DIODE,SILICON RM11C-EIC
! D504 BZ410062 D2WTRM11C0 DIODE,SILICON RM11C-EIC
D506 AD300671 D97U01801B DIODE,ZENER MTZJ18B T-77
D508 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
! D509 AD300671 D97U01801B DIODE,ZENER MTZJ18B T-77
! D510 AD300076 D28F30DF60 DIODE,RECTIFIER 30DF6-FC
! D514 BZ410077 D2WXSB1400 DIODE,SCHOTTKY SB140-EIC
D515 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D517 AD300731 D2WXN49370 DIODE,SILICON 1N4937
D519 BZ410076 D2WXB290S0 DIODE,SILICON SB290S
D520 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D521 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D523 AD300731 D2WXN49370 DIODE,SILICON 1N4937

J2-1
 ELECTRICAL REPLACEMENT PARTS LIST
Location No. TSB P/N Reference No. Description
DIODES
D524 BZ410064 D97U03R91B DIODE,ZENER MTZJ3.9B T-77
D526 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D527 BZ410020 D97U05R11B DIODE,ZENER MTZJ5.1B T-77
D528 BZ410021 D97U05R61B DIODE,ZENER MTZJ5.6B T-77
D603 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D604 BZ410058 D97U08R21B DIODE,ZENER MTZJ8.2B T-77
D606 BZ410043 D2WT011E10 DIODE,SILICON 11E1-EIC
D702 BZ410022 D97U06R81B DIODE,ZENER MTZJ6.8B T-77
D804 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D805 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D806 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
ICS
IC101 AD302159 I56F07091A IC OEC7091A
IC199 AE000749 A3M903A015 IC S-24C04BDP-LA
! IC401 BZ611053 I01TD55220 IC AN5522
! IC501 BZ410088 0002E00610 PHOTO COUPLER LTV-817M-VB
! IC1001 BZ611001 I01DP75110 IC AN7511
TRANSISTORS
Q105 BZ510086 TPATB03003 COMPOUND TRANSISTOR KRA102MAT
Q401 BZ510028 TDUF024990 TRANSISTOR,SILICON 2SD2499
! Q402 BZ510089 TC5T01627Y TRANSISTOR,SILICON 2SC1627_Y(TPE2)
Q501 BZ510093 TJXG5NC500 FET STP5NC50FP
Q502 BZ510070 TCAT032034 TRANSISTOR,SILICON KTC3203_Y-AT
! Q503 BZ510004 TA3T016240 TRANSISTOR,SILICON 2SA1624-AA
Q504 BZ510069 TCATC31980 TRANSISTOR,SILICON KTC3198-AT(Y,GR)
Q507 BZ510069 TCATC31980 TRANSISTOR,SILICON KTC3198-AT(Y,GR)
Q601 BZ510070 TCAT032034 TRANSISTOR,SILICON KTC3203_Y-AT
Q602 BZ510070 TCAT032034 TRANSISTOR,SILICON KTC3203_Y-AT
Q603 BZ510070 TCAT032034 TRANSISTOR,SILICON KTC3203_Y-AT
Q606 BZ510070 TCAT032034 TRANSISTOR,SILICON KTC3203_Y-AT
Q607 BZ510069 TCATC31980 TRANSISTOR,SILICON KTC3198-AT(Y,GR)
Q609 BZ510069 TCATC31980 TRANSISTOR,SILICON KTC3198-AT(Y,GR)
Q610 BZ510070 TCAT032034 TRANSISTOR,SILICON KTC3203_Y-AT
! Q804 BZ510091 TCA0042170 TRANSISTOR,SILICON KTC4217(O,Y)
! Q805 BZ510091 TCA0042170 TRANSISTOR,SILICON KTC4217(O,Y)
! Q806 BZ510091 TCA0042170 TRANSISTOR,SILICON KTC4217(O,Y)
COILS &TRANSFORMERS
L401 BZ310063 022100027A COIL,LINEARITY ELH5L4113
! L501 AD301395 029T000104 COIL,LINE FILTER 1R0A562F20
! L503 BZ310033 028R200026 COIL,DEGAUSS 8R200026
T401 BZ310157 045009003J TRANS,HORIZONTAL DRIVE ETH09K14BZ
! T501 AD302296 0481291144 TRANSFORMER,SWITCHING 81291144
JACKS
J710 AD300110 060G401047 RCA JACK HTJ-032-03AY
J711 AD300111 060G401046 RCA JACK HTJ-032-03AW
! J801 AD301356 066F130020 SOCKET,CATHODE RAY,TUBE ISHS53S
SWITCHES
SW101 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
SW102 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
SW103 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
SW104 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
SW105 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
VARIABLE RESISTORS
VR401 BZ210238 V1K6313BTE VOLUME,SEMI FIXED NVG6TLTAB102
VR402 BZ210237 V1K63Q4BTE VOLUME,SEMI FIXED NVG6TLTAB473
VR502 BZ210108 V116313BTC VOLUME,SEMI FIXED EVNCYAA03B13
P.C.BOARD ASSEMBLIES
PCB010 AD302335 A3M903A010 PCB ASS'Y TMC563A
PCB110 AD302336 A3M903A110 PCB ASS'Y TCC425A
MISCELLANEOUS
B501 BZ310200 024H003553 CORE,BEADS W5RH3.5X5X1.0
B503 BZ310121 024HT03553 CORE,BEADS W5RH3.5X5X1.0
B504 BZ310121 024HT03553 CORE,BEADS W5RH3.5X5X1.0
BT001 AE000012 1412004008 BATTERY,MANGAN R03(AB)E_2P_G
BT002 AE000012 1412004008 BATTERY,MANGAN R03(AB)E_2P_G
! CD501 BZ614407 120R415906 CORD,AC BUSH 0R415906
CD801 BZ614175 06CU82039A CORD,CONNECTOR SM1098-009-1A
CD802 AE000677 WDL6046038 FLAT CABLE AWM2468 A WG26 6C BLACK 460MM
CD803 AD301450 WBL6032038 FLAT CABLE AWM2468 A WG26 4C BLACK 320MM
! CP401 BZ614303 069S450089 CONNECTOR PCB SIDE A1561WV2-A5P
CP402 BZ614444 069D01001A CONNECTOR PCB SIDE 003P-2100

J2-2
 ELECTRICAL REPLACEMENT PARTS LIST
Location No. TSB P/N Reference No. Description
MISCELLANEOUS
! CP502 AD300687 069S420110 CONNECTOR PCB SIDE A1561WV2-2P
CP601 BZ614102 0694270139 CONNECTOR PCB SIDE 173979-7
CP801 BZ614269 069S320010 CONNECTOR PCB SIDE A2361WV2-2P
CD1001 AD301494 06CH12403B CORD,CONNECTOR CH12403B
CP1001 AD301495 069W120019 CONNECTOR PCB SIDE TID-X02P-B2
CP802A BZ614333 067U006049 WIRE HOLDER B2013H02-6P
CP802B BZ614333 067U006049 WIRE HOLDER B2013H02-6P
CP803A BZ614334 067U004029 WIRE HOLDER B2013H02-4P
CP803B BZ614334 067U004029 WIRE HOLDER B2013H02-4P
EL001 BZ614043 124116281A EYE LET XRY16X28BD
EL002 BZ614044 124120301A EYE LET XRY20X30BD
! F501 AD301046 081PC6R305 FUSE 51MS063L
! FB401 AD302299 043221012F TRANSFORMER,FLYBACK FQI-21B002
FH501 BZ614005 06710T0006 HOLDER,FUSE EYF-52BC
FH502 BZ614005 06710T0006 HOLDER,FUSE EYF-52BC
OS101 AD301048 0773071001 REMOTE RECEIVER RPM7138-H5
! RY501 AD300114 0560V20115 RELAY ALKS321
! SP1001 BZ614029 070C533008 SPEAKER 810-47-171
! TH501 AD302000 D8EE0B1400 DEGAUSS ELEMENT B59203-S1060-B14
TM101 AD301335 076N0EH020 TRANSMITTER RC-EH020
! TU001 AD302169 0163100002 RF UNIT ENG36A01G
! V801 AD302300 098Q210449 CRT W/DY A51AEZ90X24
X601 AD302003 100CT3R505 CRYSTAL HC-49/C

RESISTOR
RC................... CARBON RESISTOR

CAPACITORS
CC................... CERAMIC CAPACITOR
CE................... ALUMI ELECTROLYTIC CAPACITOR
CP................... POLYESTER CAPACITOR
CPP.................. POLYPROPYLENE CAPACITOR
CPL.................. PLASTIC CAPACITOR
CMP....................... METAL POLYESTER CAPACITOR
CMPL................ METAL PLASTIC CAPACITOR
CMPP................ METAL POLYPROPYLENE CAPACITOR

J2-3
 TOSHIBA CORPORATION
1-1, SHIBAURA 1-CHOME, MINATO-KU, TOKYO 105-8001, JAPAN