Scribd
Upload
27 views

Experimental-Research-Progress-Report - Form - Natividad Et Al.

The document details the researchers gathering components like a 12V battery, alternator, DC motor and other parts over multiple dates to construct a DC powered generator for experimental research. They purchased a DC motor online and received it. One researcher found a suitable alternator and pulley. They gathered all components and canvassed for pricing. Finally, a custom belt pulley and frame were made for the motor and alternator to complete the generator construction.

Uploaded by

vince.ortega
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
27 views

Experimental-Research-Progress-Report - Form - Natividad Et Al.

The document details the researchers gathering components like a 12V battery, alternator, DC motor and other parts over multiple dates to construct a DC powered generator for experimental research. They purchased a DC motor online and received it. One researcher found a suitable alternator and pulley. They gathered all components and canvassed for pricing. Finally, a custom belt pulley and frame were made for the motor and alternator to complete the generator construction.

Uploaded by

vince.ortega
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 9

UTILIZATION OF DC-POWERED GENERATOR AS A FUEL-LESS ALTERNATIVE

ELECTRICAL SUPPLY

An Experimental Research Progress Report

Presented to the

Faculty of the Senior High School Department

La Salle University

Ozamiz City, Philippines

In Partial Fulfillment

Of the Requirements for the subject

RESEARCH PROJECT

by

MARC KHYNT NATIVIDAD


VINCE MATTHEW D. ORTEGA
IZZY RAUT
MARC ANTHONIE SUICO
LYAN JOHN VILLAFUERTE

March 2024
I. Gathering of Research Instruments Part 1
II. Date Conducted: February 10, 2024, 6:54pm - 7:30pm
In this Activity, one of the Researchers (Marc Anthonie Suico) had checked
around his locale for components that the Researchers could use for Data Gathering .
The Researcher had found a 12 volt Battery and a Car Alternator. Both are to be used
for Research. However in the 3rd picture, this Alternator could not be utilized, only
the Battery.
III. Gathering of Research Instruments Part 2
IV. Date Conducted: February 22, 2024, 8:10pm
In this Activity, The Researchers had a meeting with the agreement of purchasing
a 12 volt DC Motor online (Shopee). Where the payment would be divided into 5,
where each researcher had payed their part.

V. Gathering of Research Instruments Part 3


VI. February 27, 2024, 6:41am

In this Activity, one of the Researchers (Marc Anthonie Suico) had found an
Alternator that can be used for Research.
VII. Gathering of Research Instruments Part 4
VIII. March 1, 2024, 11:50am

In this Activity, one of the Researchers (Marc Anthonie Suico) had received the DC
Motor.
IX. Gathering of Research Instruments Part 5 and Canvassing of Materials
X. March 11, 2024, 9:57am - 11:33am

In this Activity, the Researchers (Marc Anthonie Suico, Lyan John Villafuerte,
Marc Khynt Natividad & Vince Matthew D. Ortega) had agreed to meet in our
Research Locale to gather all the components that are on hand. Moreover, the
researchers had found a Belt (101 teeth) and tried to remove the Chain Pulley to
replace such with a Belt Pulley for Research, and could not find a replacement as that
moment. The researchers then went outside to Canvas for the remaining components
for pricing and for further negotiation.
XI. Gathering of Research Instruments Part 6
XII. March 12, 2024, 7:26pm

In this Activity, the Researchers (Marc Anthonie Suico) had found a pulley and a
much more suitable belt that could be used for Research. Unfortunately the pulley
was not the right size on the DC Motor Shaft so the search for a pulley continues
XIII. Construction of the DC Powered Generator.
XIV. Date Conducted: March 16-20, 2024

In this Activity, the Researchers (Vince Matthew D. Ortega) had went to a Milling
Store on March 16 to have a Custom Belt Pulley. Afterwards, on March 18, as the
researcher received the Custom Belt Pulley he then went to a Car Mechanic Shop to
have a Custom Frame for the 12 volt DC Motor and Alternator which was received
on March 20. Additionally, a new 12 volt battery served as a replacement for the
other battery prior.

You might also like