Interface Matrix

S.No Issue Description Types of Interface E&M Contractor responsibility Other contractor responsibility

Provide necessary provision of cut-out in transformer

Provide cable / bus duct route and cut-out / opening cage and terminals for cable / bus duct connections.
required in the switchgear panel cage.
Cable / bus duct installation
Furnish requirement of forced air cooling.
1 between transformer and MDB with E&M & PST
Supply and install cables / bus duct (From secondary
termination.
of transformer) including all hardware for necessary Provide necessary fixing arrangement required for 4
connections on both ends. Nos. 3.5 core x 400 sq.mm Al. cable terminations at
LT side in transformer cage.

Provide ACBs requirements in the design of MDB

(Incomers & Busbar) as per auxiliary load. Adequate
space for accommodating the ACBs shall be provided.
Traction contractor shall provide transformer rating to
2 ACBs in MDB E&M & PST
E&M contractor.
Supply and install the ACBs/Bus coupler in the MDB.
Connection of both sides of ACBs is also in the scope
of E&M contractor.

E&M contractor shall provide Control cable from both

incomers ACB and Bus coupler, DG AMF panel & UPS Provide I/O list for SCADA and functional interlocking.
Monitor the status and Control to Remote Terminal Unit (RTU) for SCADA Tentative list of I/O list is provided in table – SCADA
cabling from MDB, DG AMF and connectivity. signals.
3 E&M & PST
UPS upto Remote Terminal Unit
(RTU). Provision of scheme in MDB panel, DG AMF Panel E&M contractor shall provide cable inside the RTU &
(DG), UPS for SCADA as per the requirements Termination shall be done by Traction Contractor.
suggested by Traction contractor.

MDB testing including ACB testing in the responsibility Associate with E&M contractor for ACB testing
4 MDB testing E&M & PST
of E&M contractor. including coordination with ACB manufacturer.

Installing the LV equipment’s in the scope of E&M

contractor as per the layout drawings provided by Providing of Cable Trays and its support for
ASS layout and cable support DDC. requirement of HV (33kV) and other cables of traction
5 E&M & PST
infrastructure in ASS and in other areas within the stations shall be
Interfacing and coordinating with Traction contractor done by traction contractor.
for ASS layout.

E&M contractor shall provide distribution board for via- Traction contractor shall provide load of lighting,
Distribution board for Via-duct duct lighting & Isolator for power socket. power socket & requirement of out-goings in
6 E&M & PST distribution board to E&M contractor.
lighting & power socket.

Civil contractor shall provide the suitable arrangment

E&M contractor shall Supply & Install the Distribution for viaduct lighting, ensuring proper interface with E&
7 Lighting on Viaduct E&M & Civil M Contractor.
board & lighting system for Viaduct.

Confirming / providing comments and signing the

pump room layout drawings as provided by DDC and
Coordinating with DDC for pump layout. E&M contractor. Installation of pumps pedestal is in
Installing the equipment’s under the scope of E&M the scope of civil contractor.water pumps installation
contractor viz. control panels, fire pumps, jockey is under the scope of Plumbing contractor and Fire
8 Pump room layout and cabling E&M & Civil
pump, fire suppression system piping. fighting pumps installed by the E&M Contractor .
Install all the cables and termination including cable for
water pumps from power panels. Final connection of water pumps on pump side and
testing of pumps to be done by the civil /plumbing
contractor.

Provide requirements of niches, cut-outs etc. as

Cable routing, pipe routing and required for cable / pipe routings and DBs fixing.
Provide niches and cut-outs as required by the E&M
9 distribution board fixing in the E&M & Civil
contractor.
station building Install cables, pipes and DBs as required including
support system.

Civil contractor will provide foundation & Trench for for

DG set as per the requirement given by E&M
Installation, testing & commissioning of DG set with all contractor.
10 DG set Installation E&M & Civil
monitoring & Ventilation compliances.
E&M contractor will give requirement consultation with
DDC.

Pump room equipment handling Furnish requirements of handling facilities viz. chain Install handling facilities as required by E&M civil
11 E&M & Civil
facilities pulley lifting hook etc. and its location contractor

Civil contractor shall provide suitable location for outer

unit.
Install the outer unit in such a way that it is accessible
for maintenance conveniently.
DDC/Arch and E&M shall provide GFC support at
12 AC Split unit E&M & Civil
construction stage.
Fabrication / installation of suitable stand for
installation of outer units.
Provide suitable location for A/C outdoor units for
easy maintenance access

Civil contractor provide drains / drain traps as required

to be connected to station drainage system.
13 Drain for Air- conditioners E&M & Civil Furnish requirement of drainage & drain traps.
DDC/E&M provide GFC support at construction stage
 Civil Contractor shall provide and install handling
ASS ingress / egress route and Furnish requirement of handling facilities required and
14 E&M & Civil facilities as required and provide ingress / egress
handling facilities ingress / egress sizes
route including closing / opening arrangement.
 Furnish size and tentative location to Civil Contractor Construction as per requirement of E&M contractor.
15 Water tank for fire fighting E&M & Civil including sleeves in the tank walls as required (to Installation of tanks, sleeves, tank drain,pump room
avoid drilling at a later stage). drain etc. to be provided by the civil contractor

Slope and foundation of pump Provide slope, foundation & drain as required by E&M
16 E&M & Civil Advise requirement to Civil Contractor for slope.
room & DG room. contractor
Advise requirement to civil contractor for size and Construct the cabinet niches as required by E&M
17 FHC cabinet construction E&M & Civil
location. contractor.

Civil contractor provide drains / drain traps as required

to be connected to station drainage system.
18 FHC drain provision E&M & Civil Coordinating with DDC and E&M the location of FHC
DDC/E&M provide GFC support at construction stage

Civil contractor provide drains as required and

19 Station Drainage Civil
connected to station drainage system.

Design E&M contractor shall interface & DDC shall

furnish the fixture and LA location plans & welding
requirement on the steel structure on platform roof.
Provide structure member to E&M Contractor for
Installation of Platform lighting and
20 E&M & Civil Contractor shall install LA & Light Fixture including installation of Lighting, raceway, Cable tray & LA
lighting arrestor.
raceways, Cable Support, fixture support arrangement support as per detail furnished by DDC.
& welding to the structure other fabrication items
required for fixing the lights.

S&T Contractor shall provide details of earthing

requirements and connection from MET onwards to
Provide earthing system / arrangement as required up their equipment’s.
to Main Earth Terminals in ASS. Clean earth shall be
provided in S&T, SCR, SER & EFO rooms. Traction contractor shall provide details of earthing
21 Earthing arrangement E&M, S&T, PST & Civil Provide all earthing strips buried in floor or wall as the requirements and connection from MET onwards to
case may be. Interface with Civil Contractor and their equipments.
furnish requirement for providing niches / cut-outs for
routing the earthing strips. Civil Contractors shall provide niches / cutouts & route
for earthing as required by E&M contractor for
earthing strips.

Shall provide the cable tray & raceway requirements

Provide all power and data cable trays and raceway to E&M contractors.
Cable trays & Cable tray support
22 E&M, S&T for S&T as per their requiremnets except inside the
arrangement for S&T
rooms. Shall coordinate with E&M contractors for timely
completion of cable tray installation.

Civil contractor shall provide space to mount solar

Installation, testing & commissioning of solar power module. Access for maintenance & cut-outs for cable
23 Solar power E&M & Civil
shall be done by E&M contractor. shall be provided by civil contractor as per the
requirement of E&M contractor.

Provide 2 nos each of pipe earthing pits on both sides

Shall confirm the earthing requirements.
of the Station ( RHS &LHS ) for Lift and escalators.
Earthpit arrangement for Elevators
24 E&M , L&E
& Escalators Shall keep record off all the earth resistance value
Shall handover the earth pits to L&E contractors after
measurements of each lift and escalator
mutal sign of the ER values

Earthing arrangement for Elevators

Provide all earthing strips buried in floor or wall as the
25 & Escalators & their respective E&M , L&E Provide details of MET locations for each L&E.
case may be upto the respective L&E MET's.
panels.

Provide all power cables & connections from LT

Switchboard upto Elevator main power panel,
Provide details of power requirements, routes and
Power Cabling and cable trays, Escalator main power panel including cable trays,
26 E&M , L&E connection from LT Switchboard onwards to their
support arrangement for L&E support as per the requirements of respective
equipments.
contractors (termination on L&E will be in the scope of
respective contractors).

Raceway Arrangements for Shall provide the raceways including the tapoff box for
27 E&M , Escalator Shall confirm the size and routing of raceways.
Escalator power and data cables.

Shall confirm the location of cable tray entry on both

Data Cabling and cable trays E&M shall provide the required branches from data sides.
28 E&M , L&E
support arrangement for L&E tray at L&E and SCR room cable tray cutout.
Shall coordinate with S&T contractor for cable pulling.

Fire alarm signal interface from Shall provide the required cabling and monitor module shall specify the connection point in the escalator
29 Escalator control panel ( escalator E&M , Escalator for receiving and transmitting fire alarm related signals control panels and provide all the details of the
internal Fire) from Escalator control panel to Station fire alarm panel connection port

shall specify the connection point in the escalator

control panels and provide all the details of the
Fire alarm signal interface from Shall provide the required cabling and relevant module
connection port
30 Escalator control panel ( station fire E&M , Escalator for transmitting fire alarm related signals to escalator
) control panel
shall confirm the escalator comes to stop when fire
alarm is activated.

Fire alarm signal interface from Lift

Shall provide detectors and response indicator in Lift shall coordinate with the E&M contrctor for timely
31 control panel ( escalator internal E&M , Lift
shaft for monitoring fire scenarios installation of detector
Fire)
 shall specify the connection point in the lift control
panels and provide all the details of the connection
Shall provide the required cabling and relevant module
Fire alarm signal interface from Lift port
32 E&M , Lift for transmitting fire alarm related signals to lift control
control panel ( station fire )
panel
shall ensure that fireman mode is activated and lift
comes to the parent floor during fire sceanrio.

Shall provide the required no's power sockets inside

Shall specify the no's of sockets and power
33 Power Sockets for RMS Panel E&M , L&E the SCR room as per requirements of Lift & Escalator
requirements for RMS panel in SCR room.
contractors for RMS panel.
230V single phase UPS power Shall provide the necessary cabling from LT source to
34 E&M , L&E Shall confirm the UPS power requirements.
supply for L&E L&E control panel.

Shall provide the required cabling for relevant module shall specify the connection point and provide all the
Fire alarm signal interface with E&M , CCTV, Access,
35 for transmitting fire alarm related signals to CCTV, details of the connection port for fire alarm related
CCTV PA & AFC
Access, PA & AFC. signals.