SPECIFICATION

MODEL NO. IB-645GS

IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed, Including the
following:
1. Read all instructions thoroughly.
2. Before using the unit, check if the voltage indicated corresponds with the convenience outlet
(230Va.c.).
3.Do not use the two-way socket with another appliance.
4.Do not use any appliance with a damaged cord or plug. If the cord is damaged it should be replaced
with the same type and size or bring the unit to the nearest Service Center
5. Do not place the unit near a gas stove, an electric burner or in a heated oven.
6.Place the unit on stable surface; keep it away from the edge of counter to avoid accident
7. Children should be supervised to ensure that they do not play with the appliance.
8. This appliance is not intended for use by persons (including children) with reduced
physical sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliances by a person responsible for their safety.
9. The maximum continuous operating time of the blender is one minute only. Do not exceed with the
maximum operating time. It may cause damage to the unit.
10. To protect against electric shock, do not immerse the base in water or any other liquid.
11. Extreme caution must be exercised when using an appliance containing hot liquid in the blender
when blending as it can be ejected out of the appliance due to sudden steaming.
12.Use of accessories or equipment not supplied by the manufacturer may cause damage or
malfunctioning of your appliance or result in injuries.
13. Use on a hard, flat level surface only, to avoid interruption of air flow underneath the appliance.
14. Carry or move the blender's tumbler only by its handle.
15. Switch off the appliance and unplug the unit before replacing tumbler or accessories.
16. Blade is sharp, handle it carefully.
17. Do not put the blade assembly on the base without the tumbler.
18. Do not use the blender if the tumbler has a crack.
19. This appliance is not intended for outdoor use.
20. Never place the blender near hot surfaces.
21. In case of malfunctions, please bring the blender to the nearest Authorized Service Center.
22. Avoid water spillage into the socket, connector, cord and alike.
23. Switch off the appliance before removing the glass jar into the motor base.
24. Do not use this unit other than its intended use.
25. For household use only; not intended for any business purposes
26 Save this instruction manual for future reference.
27 CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this
appliance must not be supplied through an external switching device, such as a timer, or connected to a
circuit that is regularly switched on and off by the utility.

DESCRIPTION OF PARTS:
MEASURING CUP
GLASS JAR
STAINLESS STEEL
BLADES
BASE UNIT
SPEED CONTROL
KNOB
SUCTION
FOOTING
HOW TO ASSEMBLE:

IMPORTANT: The blender jar and blades are subject to wear during regular use. Always inspect the jar
for nicks, chips or cracks. Always inspect blades for broken, bent or loose blades. Avoid using the jar or
blades if damaged. Contact the Authorized Service Center to obtain evaluation and repair.

Make sure that the blender is unplugged. Place blender base on clean, dry surface to keep foreign
particles from being pulled up into motor during operation.
1. Place the rubber packing into the blade assembly and put the assembly into the jar support (See pic
1&2).
2. Assemble the jar support assembly into the glass jar.
3. Put the measuring cup into the lid (See pic. 3)
4. Secure the lid into the glass jar and press down. (See pic.3)
5.Put the glass jar on the motor base, press down and turn clockwise until securely engaged. (See pic. 4)
Note: The blender will not work if the glass jar is not properly attached to the unit base.

HOW TO USE:

1. For initial use, wash glass jar with blade assembly thoroughly.” Please refer to cleaning and
maintenance method #2 “. Wipe it dry.
2. Put the glass jar with blade assembly on the motor base.
3. Plug the unit into the convenience outlet.
4. Be sure to remove the seeds of the fruits/vegetables if needed.
5. Put the desired mixture.
6. Put the lid on the glass jar and close securely. Place the center lid into the hole of the lid and push
down to lock.
7. Plug the unit into the convenience outlet.
8. Press the pulse button first to crack the ice.
9. Select the speed and function.
a. Speed 1-Function is for blending soft vegetables, soft fruits or any light mixture
b. Speed 2-Function is for blending hard vegetables and hard fruits or if you desire to blend
smoothie or any alike
c. Speed 3-Pulse It is the function to crush the ice.
10. Additional ingredients can be added through opening in the lid.
11. Turn OFF and unplug the unit after every use.
NOTE:
(1) Some electric smell may be observed on first use.
(2) Maximum continuous operating time is 1 minute only.

CAUTION: Always put water or liquid in the jar to avoid damage to the unit. Use pulse function first, if
you are blending with ice.

USEFUL TIPS:
-To achieve the best results when pureeing solid ingredients, place small portions through the opening
in the lid one by one.
- When mixing solid ingredients, start with a small amount of liquid. Gradually add more liquid through
the opening in the lid.
-For stirring solid of very thick liquid ingredients, we recommend that you use the blender in pulse mode
to prevent the blades from being stuck.
CLEANING AND MAINTENANCE:
Motor Base
1. Unplug the unit from the convenience outlet.
2. Wipe or clean the outside surface with a damp or soft cloth.
NEVER IMMERSE MOTOR BASE IN WATER OR OTHER LIQUID.
3.Thoroughly clean speed selector knob so that it works freely. It will become sticky when in use. Use a
cloth or sponge to flush and clean the groove around the water shielded Switch. You may also lightly
spray the surface around the switch with an all-purpose cleaner and work the switch back and forth a
few times to loosen any dried residue under switch.
4. Polish with a soft cloth.
5. Always be sure wring excess water out of cloth or sponge when cleaning around the controls or any
electrical part.
Lid/Center Lid
Wash in warm soapy water. Rinse by a running water and dry. Reassemble before use.
Container and Blade Assembly:
Method #1
 - After use, add warm water and a splash of vinegar to blender jar. Turn ON and let the blender
work the liquid for about a minute. Pour out, rinse the blender jar well.
Method #2
- Fill the blender jar half way with warm water, add a small amount of liquid dish detergent and
turn the unit ON for about 30 seconds. Repeat if needed. Rinse well.
Method #3
- If blender was left sitting until there is dried, crusty food bits inside: fill with warm, soapy water
(or vinegar water) and let sit for about 30 to 60 seconds. Empty water to about half and then
blends for 30 second intervals until clean.

1. Turn OFF the unit and wait for the blade and motor to stop.
2. Always unplug the unit after every use.
3. Remove the blade assembly by turning it clockwise.
4.Wash the rubber packing, blade and jar support with soap and water.
5. Turn the plastic jar upside down to remove excess water.
6.Wipe the plastic jar and blade with soft cloth to dry. Make sure reassemble the unit properly before
storing it.
7.Never leave food inside the blender jar for a long period of time.
8.Store the blender on a dry cool place.
NOTE: NEVER ALLOW THE BOTTOM OF THE BLADE TO GET WET.

TROUBLE SHOOTING:
PROBLEM CAUSE SOLUTION
Motor not working 1. Convenience outlet is not 1. Check the outlet where the
working. unit is plug in if it is working.
2. Damage on the unit 2. Check for any damage.
3. Bring the unit to the nearest
Authorized Service Center.
Motor stop during operation 1. Overload protection activated 1. Unplug and let the unit rest
for at least 1 minute.
Smoke and burnt smell 1. Unit is use for the first time. 1. Its normal for the first use
Occurred
Leak on the bottom of the jar 1. Rubber packing is not 1. Turn OFF the unit. Remove
properly installed the jar and the rubber.
2. Rubber was damaged Reassemble the unit.
2. Replace the rubber with the
new one.
 3. Bring the unit to the nearest
Authorized Service Center
Attachment Not functioning 1. Not properly install 1. Turn off the unit and check
the assembly