Colves Fluid Control

Check Valves
Swing check, dual plate and tilting check
are non- return type valves, suitable for oil,
gas, water and refining, where the prevention
of flow reversal is mandatory.
The flow characteristics require a special
attention to ensure the correct valve selection.

Summary
All products manufactured by Colves Fluid Control
are in compliance with:

PED 2014/68/UE 0496

03 Characteristics of Check Valves ATEX 2014/34/UE
04 Swing Check Valves 150 Lb - 300 Lb
06 Swing Check Valves 600 Lb - 900 Lb
08 Swing Check Valves 1500 Lb - 2500 Lb COLVES FLUID CONTROL IS A REGISTERED TRADEMARK
10 Dual Plate Wafer Check Valves All the photos and drawings reproduced
150 Lb - 1500 Lb on the present catalogue are the property of
Colves Fluid Control.
11 Wafer Tilting Disc Check Valves ALL RIGHTS ARE RESERVED.
150 Lb - 1500 Lb
The use, even partial, of the published photos,
drawings and technical data will be allowed
only under Colves Fluid Control’ s authorization.

All technical data and information contained in

the present catalogue are to be considered
only indicative and Colves Fluid Control reserves
the right to make modifications without notice.

For any technical information, please refer to

section no. 10 of the present catalogue.

The compatibility between the materials of the

products and the working conditions shall be
evaluated by the End user, who can eventually
ask Colves Fluid Control for a technical support.

02
Cast Steel Swing Check Valves 150-300-600-900-1500-2500 Lb
Dual Plate Wafer Check & Wafer Tilting Disc Check Valves 150-1500 Lb

Cast Steel Swing Check Valves

15
13

14

11
12

7 6

8 5

4
1
3

2 16 17

N° Part Name N° Part Name

01 Body 09 Nameplate (not represented)
02 Seat 10 Rivet (not represented)
03 Disc 11 Cover Gasket
04 Washer 12 Cover
05 Disc Nut 13 Stud Bolt
06 Disc Pin 14 Nut
07 Hinge 15 Eyebolt
08 Pin 16-17 Plug Gasket - Plug

03
 Cast Steel Swing Check 150 Lb - 300 Lb

12 14 15
11 13
10
9
8
7

H
6
5
4
3
2
BASIC DESIGN STANDARDS
Basic design API 6D BS 1868 L1
Face to Face ANSI B16.10 1
Flanges up to 24” ANSI B16.5
from 26” MSS SP44
ANSI B16.47 API 605 L
Butt-weld ends ANSI B16.25
Testing API 598

STANDARD DESCRIPTION
• Full Opening (API 6D only)
• Swing Type Disc 16
• Bolted Cover
• Welded Seat Ring 17 *Recommended Spare Parts
• < ø 4” without eyebolt
• Special features according to Customer's
requirement
TRIM-MATERIALS ACCORDING TO API 600*
TEST PRESSURE TO API 6D psi/bar NO Part Name TRIM NO
150 Lb 1 2 5 8 9 10 11 12 14 15 16 18 70
Shell (water) Seat (water) Seat (air) 2 Seat STL6 STL6 STL6 STL6 STL6 STL6 STL6 STL6
425/29 300/21 80/6 3 Disc STL6 STL6 STL6 STL6
4 Washer Bronze
300 Lb
5 Disc Nut 410 304 410 410 Monel 316 Monel 316 Alloy 20
Shell (water) Seat (water) Seat (air)
6 Disc Pin 304 316 Alloy 20
1100/76 800/55 80/6
8 Pin
17 Plug
* Body & Trim Material Design Also According to Customer's requirement.

STANDARD MATERIAL SPECIFICATIONS (ASTM)

Carbon Steel Alloy Steel Stainless Steel
NO Part Name WCB LCB WC6 CF8 CF8M
1 Body WCB LCB WC6 CF8 CF8M
2 Seat A105 LF2 F11 304 316
3 Disc WCB LCB WC6 CF8 CF8M
7 Hinge WCB LCB WC6 CF8 CF8M
9 Nameplate 304
10 Rivet 304
11 Cover Gasket Graphite + Stainless steel
12 Cover WCB LCB WC6 CF8 CF8M
13 Stud Bolt B7M L7M B16 B8 B8
14 Nut 2HM 7M 4 8 8
15 Eyebolt 1025
Wedge during stelliting process 16 Plug Gasket Graphite + Stainless steel

04 Colves Fluid Control

 0496 API 6D-0444
Dimensions in mm
Size Class 150 Lb Class 300 Lb
L (RF)* Weight L (RF)* Weight Swing Check valve

Cast Steel Swing Check Valves 150 Lb - 300 Lb

inches mm L1(BW)* H Kg L1(BW)* H Kg in Aluminium
Bronze B148 - C 95500
2” 50 203 146 19 267 178 24 for marine application
21/2" 65 216 160 22 292 190 33
3” 80 241 172 28.5 318 231 44
4” 100 292 209 49 356 268 75
6” 150 356 312 76 445 328 124
8” 200 495 363 140 533 406 188
10” 250 622 444 207 622 460 325
12” 300 698 519 330 711 550 475
14” 350 787 596 409 838 608 690
16” 400 864 611 602 864 666 900
18” 450 978 655 680 978 695 1100
20” 500 978 668 750 1016 700 1330
Swing Check valve
22” 550 1067 724 - 1118 825 - complete with
24” 600 1295 763 1280 1346 1080 1950 counter weight
32” 800 1524 1060 2900 2083 1475 4900
36” 900 1956 1350 3690 2083 1770 6300
48” 1200 2591 1870 - 2743 2070 -

* Face to face, end to end dimensions

ANSI CLASS 150 /300 Pressure -Temperature Ratings to ANSI B16.34

WORKING PRESSURE (bar)
WCB (a) LCB (b) WC1 (c) WC6 (d) WC9 (d) C5 C12 CF8 CF8M CF3 (e) CF3M (f)
Temperature
150 300 150 300 150 300 150 300 150 300 150 300 150 300 150 300 150 300 150 300 150 300
29 to 38 19.6 51.1 18.4 47.9 18.4 47.9 20.0 51.7 20.0 51.7 20.0 51.7 20.0 51.7 19.0 49.6 19.0 49.6 19.0 49.6 19.0 49.6
50 19.2 50.1 18.1 47.3 18.3 47.6 19.2 51.1 19.2 51.2 19.2 51.7 19.2 51.7 18.4 47.8 18.4 48.1 18.4 47.8 18.4 48.1
100 17.7 46.4 17.3 45.1 17.7 46.6 17.7 48.8 17.7 49.0 17.7 51.5 17.7 51.5 15.7 40.9 16.2 42.2 15.7 40.9 16.2 42.2
150 15.8 45.2 15.8 44.0 15.8 45.0 15.8 46.4 15.8 46.6 15.8 50.2 15.8 50.2 13.9 36.3 14.8 38.5 13.9 36.3 14.8 38.5
200 14.0 43.8 14.0 42.7 14.0 44.2 14.0 45.5 14.0 44.8 14.0 48.8 14.0 48.8 12.6 32.8 13.7 35.7 12.6 32.8 13.7 35.7
250 12.1 41.7 12.1 40.6 12.1 43.1 12.1 44.5 12.1 44.2 12.1 46.3 12.1 46.3 11.7 30.5 12.1 33.4 11.7 30.5 12.1 33.4
300 10.2 38.7 10.2 37.7 10.2 42.0 10.2 42.4 10.2 42.4 10.2 42.4 10.1 42.4 10.2 29.1 10.2 31.6 10.2 29.1 10.2 31.6
350 8.4 37.0 8.4 36.0 8.4 40.2 8.4 40.2 8.4 40.2 8.4 40.2 8.4 40.2 8.4 28.1 8.4 30.4 8.4 28.1 8.4 30.4
400 6.5 34.5 - - 6.5 36.6 6.5 36.6 6.5 36.6 6.5 36.6 6.5 36.6 6.5 27.5 6.5 29.1 6.5 27.5 6.5 29.1
425 5.6 28.8 - - 5.6 35.1 5.6 35.1 5.6 35.1 5.6 34.5 5.6 35.1 5.6 27.2 5.6 28.7 5.6 27.2 5.6 28.7
450 - - - - 4.7 33.8 4.7 33.8 4.7 33.8 4.7 30.9 4.7 33.8 4.7 26.9 4.7 28.1 4.7 26.9 4.7 28.1
500 - - - - 2.8 24.1 2.8 27.8 2.8 27.8 2.8 20.3 2.8 27.5 2.8 26.1 2.8 26.8 - - 2.8 26.8
525 - - - - 1.9 15.0 1.9 23.0 1.9 21.9 1.9 15.4 1.9 22.6 1.9 23.9 1.9 26.3 - - - -
550 - - - - - - 1.3 (g) 12.8 1.3 (g) 16.4 1.3 (g) 11.7 1.3 (g) 17.0 1.3 (g) 21.8 1.3 (g) 25.0 - - - -
600 - - - - - - 1.3 (g) 5.9 1.3 (g) 7.6 1.3 (g) 6.5 1.3 (g) 7.2 1.3 (g) 16.7 1.3 (g) 21.4 - - - -
650 - - - - - - - - - - 1.3 (g) 3.0 1.3 (g) 3.5 1.3 (g) 10.5 1.3 (g) 14.1 - - - -
700 - - - - - - - - - - - - - - 1.3 (g) 6.0 1.3 (g) 9.9 - - - -
750 - - - - - - - - - - - - - - 1.3 (g) 3.7 1.3 (g) 5.9 - - - -
800 - - - - - - - - - - - - - - 1.3 (g) 2.1 1.3 (g) 3.5 - - - -

a) Permissible, but not recommended c) Permissible, but not recommended e) Not be used over 425°C (800°F)
for prolonged usage above 425°C (800°F) for prolonged usage above 455°C (850°F) f) Not be used over 455°C (850°F)
b) Not be used over 343°C (650°F) d) Not be used over 593°C (1100°F) g) For welding end valves only

05
 Cast Steel Swing Check 600 Lb - 900 Lb

12 14 15
11 13
10
9
8

H
7
6
5
4
3 L1
2
BASIC DESIGN STANDARDS
Basic design API 6D BS1868
Face to Face ANSI B16.10 1
Flanges up to 24” ANSI B16.5
from 26” MSS SP44
ANSI B16.47 API 605
L L2
Butt-weld ends ANSI B16.25
Testing API 598

STANDARD DESCRIPTION
• Full Opening (API 6D only)
• Swing Type Disc 16
• Bolted Cover
• Welded Seat Ring 17
• < ø 4” without eyebolt *Recommended Spare Parts

TEST PRESSURE TO API 6D psi/bar

600 Lb
TRIM-MATERIALS ACCORDING TO API 600
Shell (water) Seat (water) Seat (air) NO Part Name TRIM NO
2175/150 1600/110 80/6 1 2 5 8 9 10 11 12 14 15 16 18
2 Seat STL6 STL6 STL6 STL6 STL6 STL6 STL6 STL6
900 Lb
3 Disc STL6 STL6 STL6 STL6
Shell (water) Seat (water) Seat (air)
4 Washer
3250/224 2400/166 80/6
5 Disc Nut 410 304 410 Monel 316 Monel 316 Alloy 20
6 Disc Pin 304 316 Alloy 20
8 Pin
17 Plug
* Body & Trim Material Design Also According to Customer's requirement.

STANDARD MATERIAL SPECIFICATIONS (ASTM)*

Carbon Steel Alloy Steel Stainless Steel
NO Part Name WCB LCB WC6 CF8 CF8M
1 Body WCB LCB WC6 CF8 CF8M
2 Seat A105 LF2 F11 304 316
3 Disc WCB LCB WC6 CF8 CF8M
7 Hinge WCB LCB WC6 CF8 CF8M
9 Nameplate 304
10 Rivet 304
11 Cover Gasket Graphite + Stainless steel
12 Cover WCB LCB WC6 CF8 CF8M
13 Stud Bolt B7M L7M B16 B8 B8
14 Nut 2HM 7M 4 8 8
15 Eyebolt 1025
Test bench API 598 and API 6D 16 Plug Gasket Graphite + Stainless steel

06 Colves Fluid Control

 0496 API 6D-0444
Dimensions in mm
Size Class 600 Lb Class 900 Lb
L1 (BW)* Weight L1 (BW)* Weight

Cast Steel Swing Check Valves 600 Lb - 900 Lb

inches mm L(RF)* L2 (RTJ)* H Kg L(RF)* L2 (RTJ)* H Kg

2” 50 292 295 225 39 368 371 308 70

21/2" 65 330 333 250 49 419 422 325 88
3” 80 356 359 270 61 381 384 315 98
4” 100 432 435 310 103 457 460 350 137
6” 150 559 562 400 230 610 613 453 333
8” 200 660 664 460 354 737 740 506 510
10” 250 787 791 580 626 838 841 616 840
12” 300 838 841 618 790 965 968 674 1180
14” 350 889 892 657 820 1029 1039 830 1680
16” 400 991 994 710 1400 1130 1140 886 1980
18” 450 1092 1095 764 1800 1219 1232 1003 2400 Swing Check valve complete
20” 500 1194 1200 882 2300 1321 1334 1076 3200 with shock absorber
24” 550 1397 1407 1020 3330 1549 1568 1360 5500
30” 600 1651 1664 1280 6200 1829 1851 1660 -
36” 800 2083 2099 1675 9500 - - - -
40” 900 2286 2302 1790 - - - - -
* Face to face, end to end dimensions

Swing Check valve 36” class 600

complete with butt weld ends

ANSI CLASS 600 /900 Pressure -Temperature Ratings to ANSI B16.34

WORKING PRESSURE (bar)
WCB (a) LCB (b) WC1 (c) WC6 (d) WC9 (d) C5 C12 CF8 CF8M CF3 (e) CF3M (f)
Temperature
600 900 600 900 600 900 600 900 600 900 600 900 600 900 600 900 600 900 600 900 600 900
29 to 38 102.1 153.2 95.7 143.6 95.8 143.6 103.4 155.1 103.4 155.1 103.4 155.2 103.4 155.2 99.2 148.9 99.3 148.9 99.2 148.9 99.3 148.9
50 100.2 150.2 94.6 141.9 95.3 142.9 102.3 153.4 102.4 153.6 103.4 155.2 103.4 155.2 95.7 143.5 96.3 144.4 95.7 143.5 96.3 144.4
100 92.8 139.1 90.2 135.3 93.2 139.8 97.5 146.3 98.1 147.1 103.1 154.6 103.1 154.6 81.8 122.6 84.4 126.6 81.8 122.6 84.4 126.6
150 90.5 135.7 87.9 131.9 89.9 134.9 92.7 139.1 93.3 139.9 100.4 150.6 100.4 150.6 72.7 109.0 77.0 115.5 72.7 109.0 77.0 115.5
200 87.6 131.5 85.4 128.0 88.4 132.6 91.0 136.4 89.7 134.5 97.6 146.4 97.6 146.4 65.5 98.3 71.3 107.0 65.5 98.3 71.3 107.0
250 83.4 125.2 81.2 121.8 86.2 129.2 88.9 133.4 88.4 132.7 92.7 139.0 92.7 139.0 61.1 91.6 66.8 100.2 61.1 91.6 66.8 100.2
300 77.5 116.2 75.4 113.1 84.1 126.1 84.9 127.3 84.9 127.3 84.9 127.3 84.9 127.3 58.1 87.2 63.3 94.9 58.1 87.2 63.3 94.9
350 73.9 110.9 71.9 107.9 80.5 120.7 80.5 120.7 80.5 120.7 80.5 120.7 80.5 120.7 56.1 84.2 60.8 91.3 56.1 84.2 60.8 91.3
400 69.0 103.5 - - 73.2 109.8 73.2 109.8 73.2 109.8 73.2 109.8 73.2 109.8 54.9 82.4 58.2 87.3 54.9 82.4 58.2 87.3
425 57.5 86.3 - - 70.2 105.3 70.2 105.3 70.2 105.3 69.0 103.5 70.2 105.3 54.3 81.5 57.3 86.0 54.3 81.5 57.3 86.0
450 - - - - 67.6 101.4 67.6 101.4 67.6 101.4 61.8 92.7 67.6 101.4 53.7 80.6 56.2 84.2 53.7 80.6 56.2 84.2
500 - - - - 48.1 72.2 55.6 83.4 55.6 83.4 40.5 60.8 55.0 82.5 52.1 78.2 53.7 80.5 - - 53.7 80.5
525 - - - - 30.1 45.1 40.5 60.8 43.8 65.8 30.8 46.3 45.2 67.8 47.8 71.6 52.6 78.9 - - - -
550 - - - - - - 25.5 38.3 32.7 49.1 23.4 35.0 34.0 50.9 43.6 65.4 49.9 74.9 - - - -
600 - - - - - - 11.8 17.6 15.3 22.9 13.1 19.6 14.4 21.5 33.4 50.1 42.9 64.3 - - - -
650 - - - - - - - - - - 6.0 9.0 7.0 10.4 21.0 31.6 28.2 42.4 - - - -
700 - - - - - - - - - - - - - - 12.0 17.9 19.9 29.8 - - - -
750 - - - - - - - - - - - - - - 7.3 11.0 11.0 17.6 - - - -
800 - - - - - - - - - - - - - - 4.1 6.2 7.0 10.5 - - - -

a) Permissible, but not recommended c) Permissible, but not recommended e) Not be used over 425°C (800°F)
for prolonged usage above 425°C (800°F) for prolonged usage above 455°C (850°F) f) Not be used over 455°C (850°F)
b) Not be used over 343°C (650°F) d) Not be used over 593°C (1100°F)

Colves Fluid Control 07

 Cast Steel Swing Check 1500 Lb - 2500 Lb

12 14 15
11 13
10
9
8

H
7
6
5
4
3 L1
2
BASIC DESIGN STANDARDS
Basic design API 6D BS1868
Face to Face ANSI B16.10 1
Flanges up to 24” ANSI B16.5
from 26” MSS SP44
ANSI B16.47 API 605
L L2
Butt-weld ends ANSI B16.25
Testing API 598

STANDARD DESCRIPTION
• Full Opening (API 6D only)
• Swing Type Disc 16
• Bolted Cover
• Welded Seat Ring 17 *Recommended Spare Parts
• < ø 4” without eyebolt

TEST PRESSURE TO API 6D psi/bar

1500 Lb TRIM-MATERIALS ACCORDING TO API 600
Shell (water) Seat (water) Seat (air) NO Part Name TRIM NO
5400/372 4000/276 80/6 1 2 5 8 9 10 11 12 14 15 16 18
2 Seat STL6 STL6 STL6 STL6 STL6 STL6 STL6 STL6
2500 Lb
3 Disc STL6 STL6 STL6 STL6
Shell (water) Seat (water) Seat (air)
4 Washer
9000/621 6600/455 80/6
5 Disc Nut 410 304 410 Monel 316 Monel 316 Alloy 20
6 Disc Pin 304 316 Alloy 20
8 Pin
17 Plug
* Body & Trim Material Design Also According to Customer's requirement.

STANDARD MATERIAL SPECIFICATIONS (ASTM)*

Carbon Steel Alloy Steel Stainless Steel
NO Part Name WCB LCB WC6 CF8 CF8M
1 Body WCB LCB WC6 CF8 CF8M
2 Seat A105 LF2 F11 304 316
3 Disc WCB LCB WC6 CF8 CF8M
7 Hinge WCB LCB WC6 CF8 CF8M
9 Nameplate 304
10 Rivet 304
11 Cover Gasket Graphite + Stainless steel or Ring Joint
12 Cover WCB LCB WC6 CF8 CF8M
13 Stud Bolt B7M L7M B16 B8 B8
14 Nut 2HM 7M 4 8 8
15 Eyebolt 1025
Jacketed Globe valve for chemical plant 16 Plug Gasket Graphite + Stainless steel

08 Colves Fluid Control

 0496 API 6D-0444
Dimensions in mm
Size Class 1500 Lb Class 2500 Lb
L (RF)* L (RF)*

Cast Steel Swing Check Valves 1500 Lb - 2500 Lb

inches mm L1(BW)* L2 (RTJ)* H L1(BW)* L2 (RTJ)* H

2” 50 368 371 308 451 454 416

21/2" 65 419 422 325 508 514 421
3” 80 470 473 342 578 584 441
4” 100 546 549 410 673 683 479
6” 150 705 711 514 914 927 511
8” 200 832 842 592 1022 1038 712
10” 250 991 1000 673 1270 1292 854
12” 300 1130 1146 755 1422 1445 1000
14” 350 1257 1276 838 - - -
16” 400 1384 1407 1054 - - - Disck Swing Check valve Swing Check valve class 1500 Lb
18” 450 1537 1559 1305 - - -
20” 500 1664 1686 1450 - - -
24” 600 1943 1972 1690 - - -
* Face to face, end to end dimensions

ANSI CLASS 1500 /2500 Pressure -Temperature Ratings to ANSI B16.34

WORKING PRESSURE (bar)
WCB (a) LCB (b) WC1 (c) WC6 (d) WC9 (d) C5 C12 CF8 CF8M CF3 (e) CF3M (f)
Temperature
1500 2500 1500 2500 1500 2500 1500 2500 1500 2500 1500 2500 1500 2500 1500 2500 1500 2500 1500 2500 1500 2500
29 to 38 255.3 425.5 239.4 398.9 239.4 399.0 258.6 431.0 258.6 431.0 258.6 431.0 258.6 258.6 248.1 413.5 248.1 413.6 248.1 - 248.1 -
50 250.4 417.3 236.5 394.2 238.2 397.1 255.7 426.2 256.0 426.7 258.6 431.0 258.6 258.6 239.2 398.6 240.6 401.0 239.2 - 240.6 -
100 231.9 386.5 225.5 375.9 233.0 388.3 243.8 406.4 245.2 408.7 257.7 429.5 257.7 257.7 204.4 340.7 211.0 351.7 204.4 - 211.0 -
150 226.1 376.9 219.8 366.3 224.8 374.6 231.9 386.4 233.2 388.6 251.0 418.3 251.0 251.0 181.7 302.8 192.5 320.9 181.7 - 192.5 -
200 219.1 365.2 213.4 355.6 221.0 368.3 227.4 379.0 224.2 373.7 243.9 406.6 243.9 243.9 163.8 273.0 178.4 297.3 163.8 - 178.4 -
250 208.6 347.7 202.9 338.2 215.4 359.0 222.3 370.6 221.1 368.5 231.7 386.1 231.7 231.7 152.7 254.5 166.9 278.2 152.7 - 166.9 -
300 193.7 322.8 188.5 314.2 210.1 350.2 212.1 353.5 212.1 353.5 212.1 353.5 212.1 212.1 145.3 242.1 158.1 263.6 145.3 - 158.1 -
350 184.8 308.0 179.8 299.7 201.1 335.2 201.2 335.3 201.2 335.3 201.2 335.3 201.2 201.2 140.3 233.8 152.1 253.8 140.3 - 152.1 -
400 172.5 287.5 - 270.0 182.9 304.9 182.9 304.9 182.9 304.9 182.9 304.9 182.9 182.9 137.3 228.9 145.6 242.6 137.3 - 145.6 -
425 143.8 239.6 - 227.5 175.5 292.5 175.5 292.5 175.5 292.5 172.5 287.5 175.5 175.5 135.8 226.4 143.3 238.9 135.8 - 143.3 -
450 - - - 165.0 169.0 281.7 169.0 281.7 169.0 281.7 154.5 257.6 169.0 169.0 134.3 223.9 140.4 234.0 134.3 - 140.4 -
500 - - - 73.3 120.3 200.6 139.0 231.6 139.0 231.6 101.3 168.9 137.5 137.5 130.3 217.2 134.1 223.6 - - 134.1 -
525 - - - 43.2 75.2 125.4 101.3 168.9 109.6 182.7 77.1 128.5 113.0 113.0 119.4 199.0 131.5 214.9 - - - -
550 - - - - - - 63.8 106.4 81.8 13.6 58.4 97.3 84.9 84.9 109.1 181.8 124.8 208.0 - - - -
600 - - - - - - 29.4 49.0 38.2 63.6 32.6 54.4 35.9 35.9 83.6 139.3 107.2 178.6 - - - -
650 - - - - - - - 19.3 - 30.4 15.0 25.1 17.4 17.4 52.6 87.6 70.6 117.1 - - - -
700 - - - - - - - - - - - - - - 29.9 49.8 49.7 82.9 - - - -
750 - - - - - - - - - - - - - - 18.3 30.4 29.4 49.0 - - - -
800 - - - - - - - - - - - - - - 10.3 17.1 17.5 29.2 - - - -

a) Permissible, but not recommended c) Permissible, but not recommended e) Not be used over 425°C (800°F)
for prolonged usage above 425°C (800°F) for prolonged usage above 455°C (850°F) f) Not be used over 455°C (850°F)
b) Not be used over 343°C (650°F) d) Not be used over 593°C (1100°F)

Colves Fluid Control 09

09
 Dual Plate Wafer Check Valves 150 Lb /1500 Lb
0496

1 2 3 4 5 6 7 8 9

DN
Ø
L

BASIC DESIGN STANDARDS

Basic Design API 594 * Body & Trim Material Design
Face to Face API 594 STANDARD MATERIAL SPECIFICATIONS (ASTM)* Also According to Customer's requirement.
Flanges up to 24” ANSI B16.5 Carbon Steel Stainless Steel
Flanges from to 26” ANSI B16.47 NO Part Name WCB LCB CF8M
Testing API 598 1 Body WCB + 410 LCB + 316 CF8M
2 Disc WCB + 410 LCB + 316 CF8M
3 Spring 316 / Inconel
4 Hinge Pin 410 316 316
5 Pin 410 316 316
6 Bearing 410 316 316
7 Washer 410 316 316 Dual Plate Check Valves
8 Bush 410 316 316
9 Packing Graphite API 594 can be
10 Gland 410 316 316 Wafer Type
11 Stud Bolt B7 L7 B8 or Flanged Type
12 Nut 2H 7 8
Dual Plate Wafer Check API 594
in B148 for Marine application
WaFer Type Flanged Type

Flanged Wafer Check API 594

Dimensions in mm
SIZE inches 2” 3” 4” 6” 8” 10” 12” 14” 16” 18” 20” 24” 30” 32” 36”
CLASS mm 50 80 100 150 200 250 300 350 400 450 500 600 750 800 900
L (RF) 60 73 73 98 127 146 181 184 191 203 219 222 305 318 368
150 LB D 103 136 175 220 277 340 408 451 515 549 603 717 883 940 1048
Weight kg 3.2 6.4 9.5 16 36 52 97 123 133 141 215 358 662 685 710
L (RF) 60 73 73 98 127 146 181 222 232 264 292 318 368 394 483
300 LB D 111 149 181 251 308 362 422 485 540 597 654 774 953 1006 1118
Weight kg 3.2 7.7 10.5 20 40 56 98 176 210 295 365 520 950 1270 1635
L (RF) 60 73 79 136 165 213 229 273 305 362 368 438 505 559 635
600 LB D 111 149 194 267 321 400 458 492 565 613 683 791 972 1022 1130
Weight kg 3.2 7.7 12.7 36 72 118 164 186 330 394 544 820 1578 1743 2120
L (RF) 70 83 102 159 206 248 305 356 384 468 533 559 - - -
900 LB D 143 168 206 289 359 435 498 521 575 638 699 838 - - -
Weight kg 8.2 11.8 19.1 54 122 196 293 396 532 611 637 1230 - - -
L (RF) 70 83 102 159 206 248 305 356 384 468 533 559 - - -
1500 LB D 143 175 210 283 352 435 521 578 641 705 756 902 - - -
Weight kg 8.2 12.7 20.5 56 128 205 373 484 588 791 1275 2713 - - -

10 Colves Fluid Control

 Wafer Tilting Disc Check Valves 150 Lb /1500 Lb
0496

BASIC DESIGN STANDARDS

Basic Design API 594
Face to Face API 594 STANDARD MATERIAL SPECIFICATIONS (ASTM)*
Flanges up to 24” ANSI B16.5 Carbon Steel Alloy Steel Stainless Steel
Flanges from to 26” ANSI B16.47 NO Part Name WCB LCB CF8M
Testing API 598 1 Body WCB + STL LCB + 316 CF8M
2 Disc WCB + 410 LCB + 316 CF8M
3 Hinge Pin 410 316 316
4 Eyebold 1025
5 Bush 410 316 316
6 Plug Gasket Graphite + Stainless steel
7 Plug 1025 LF2 316
* Body & Trim Material Design Also According to Customer's requirement

WaFer Type Flanged Type

Tilting Check Valves API 594 can be Wafer Type or Flanged Type

Dimensions in mm
SIZE inches 2” 3” 4” 6” 8” 10” 12” 14” 16” 18” 20” 24”
CLASS mm 50 80 100 150 200 250 300 350 400 450 500 600
L (RF) 60 73 73 98 127 146 181 184 191 203 219 222
150 LB
D 102 136 175 220 277 340 408 451 515 549 603 717
L (RF) 60 73 73 98 127 146 151 222 232 264 292 318
300 LB
D 111 149 181 251 308 362 422 485 540 597 654 774
L (RF) 60 73 79 136 165 213 229 273 305 362 368 438
600 LB
D 111 149 194 267 321 400 458 492 565 613 683 791
L (RF) 70 83 102 159 206 248 305 356 384 468 533 559
900 LB
D 143 168 206 289 359 435 498 521 575 638 699 838
1500 LB L (RF) 70 83 102 159 206 248 305 356 384 468 533 559
D 143 175 210 283 352 435 521 578 641 705 756 902

Colves Fluid Control 11