Hitachi Proprietary DKC810I

Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.

INST03-01-10

3. Hardware Installation
3.1 Common Item of Installation and De-Installation
3.1.1 Bezel Opening-Closing Procedure

CAUTION
Attach or remove the bezel carefully following the procedure. Otherwise, you may hurt
your fingers by pinching them.

NOTICE: • To prevent part failures caused by static electrical charge built up on your
own body, be sure to wear a wrist strap connected to the chassis before
starting and do not take it off until you finish.
• When inserting and turning the key, have it inserted completely. If it is turned
when it is inserted half way, a damage of it may be caused.
• When removing the key after locking up the bezel, pull it off aligning its
groove with the positioning mark on the lock.
When the key is pulled off in the state where its groove is not aligned with
the positioning mark on the lock, a damage of the lock may be caused.

Key
Insert or pull off the key aligning its
groove with the positioning mark on
the lock.
Unlocking
The key cannot be pulled off when its
Operate while pressing the groove is not aligned with the
key to the keyhole. positioning mark on the lock.

INST03-01-10
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-01-20

1. DKC Bezel (8U)

A key is necessary to attach or remove a bezel.

Procedure for removal

a. Insert the key into the keyhole on the bezel and release the lock of the bezel ().
b. Pull the key toward you while holding the lower right portion of the bezel, and then
disengage the right side of the bezel from the ball catch ().
NOTE: When disengaging the bezel, work with the opening angle between the bezel
and the chassis of up to 45 degrees.
Do not force the bezel open too wide. Otherwise, a damage of bezel may be
caused.
c. Disengage the bezel from the left tabs and then remove it ().

Tab

Tab Hole

 Ball Catch




The state in which the slit of the Key

keyhole is aligned with the mark.
(The key can be inserted or pulled out
in this state.)

Keyhole DKC Bezel (8U)

To lock About 45 degrees

To unlock

Fig. 3.1.1-1 Removal of DKC Bezel (8U)

INST03-01-20
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-01-30

Procedure for attachment

a. Unlock the bezel with the key, and hold the key and bottom of bezel with your both
hands.
b. Insert the tabs on the left front side of the chassis into the tab holes on the bezel ().
c. Fix the bezel by pressing the right side of the bezel to engage it with the ball catch on
the front side of the chassis ().
d. Lock the bezel with the key ().

Tab

Tab Hole

 Ball Catch




Key
The state in which the slit of the
keyhole is aligned with the mark.
(The key can be inserted or pulled out
in this state.)
DKC Bezel (8U)
Keyhole
To lock

To unlock

Fig. 3.1.1-2 Attachment of DKC Bezel (8U)

INST03-01-30
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-01-40

2. DKC Bezel (2U)

Operator Panel Opening Procedure
a. Push the “PUSH” as it is shown in the upper part of the operator panel, and open the
operator panel.

Operator Panel Closing Procedure

a. Close the operator panel and push the “PUSH” part until it clicks.

Push

Operator Panel
DKC Bezel (2U)

Fig. 3.1.1-3 Operator Panel Opening-Closing Procedure

Procedure for removal

a. Remove the DKC Bezel (8U) from the DKC.
b. Pull the bezel toward you holding its sides and disengage it from the ball catches to
remove the bezel.

Procedure for attachment

a. Hold the side of spare bezel with both hands.
b. After making the hooks of the bezel engaged, press the bezel against the main body
until it is stopped.

Ball Catch
DKC

Ball Catch

DKC Bezel (2U)

Fig. 3.1.1-4 Removal/Attachment of DKC Bezel (2U)

INST03-01-40
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-01-50

3. DKU Bezel
A key is necessary to attach or remove a bezel.

Procedure for removal

a. Insert the key into the keyhole on the bezel and release the lock of the bezel ().
b. Pull the key toward you while holding the lower right portion of the bezel, and then
disengage the right side of the bezel from the ball catch ().
NOTE: When disengaging the bezel, work with the opening angle between the bezel
and the chassis of up to 45 degrees.
Do not force the bezel open too wide. Otherwise, a damage of bezel may be
caused.
c. Disengage the bezel from the left tabs and then remove it ().

Tab

Tab Hole

 Ball Catch




The state in which the slit of the Key

keyhole is aligned with the mark.
(The key can be inserted or pulled out
in this state.)
DKU Bezel
Keyhole About 45 degrees
To lock

To unlock

Fig. 3.1.1-5 Removal of DKU Bezel

INST03-01-50
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-01-60

Procedure for attachment

a. Unlock the bezel with the key, and hold the key and bottom of bezel with your both
hands.
b. Insert the tabs on the left front side of the chassis into the tab holes on the bezel ().
c. Fix the bezel by pressing the right side of the bezel to engage it with the ball catch on
the front side of the chassis ().
d. Lock the bezel with the key ().

Tab

Tab Hole

 Ball Catch




The state in which the slit of the Key

keyhole is aligned with the mark.
(The key can be inserted or pulled out
in this state.)

DKU Bezel
Keyhole
To lock

To unlock

Fig. 3.1.1-6 Attachment of DKU Bezel

INST03-01-60
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-01-70

3.1.2 Attaching the Wrist Strap

• In order to protect parts from the electrostatic discharge, every worker must put a wrist strap on
his/her wrist before starting installation or maintenance work and start the work after connecting
the grounding clip to a metallic portion of the frame. (The wrist strap must be put on when
connecting the LAN, RS232C or channel interface cable.)
• When handling a part, hold it in the way that fingertips of the hand putting the wrist strap on
touch a metallic portion of the part.
(The above is necessary in order to discharge the charged static electricity and prevent a charge
caused by handling.)
• Be sure to keep the wrist strap close to the storage system.
• Be sure to touch the storage system with the wrist strap put on. If you touch the storage system
without putting on the wrist strap, the static electricity charged on your body flows to the storage
system in an instant because no resistance exists between your body and the storage system
causing a storage system trouble.
• Wear a wrist strap until the work is finished when working with the door of device or the bezel
open (for change of channel interface cable connection etc.).

Part

The clip side of wrist strap:

Support a part by touching its Connect this to the metal
metal part (metal plate) with part on the frame of
your figures. storage system.

Wrist Strap

Fig. 3.1.2-1 Attachment of Wrist Strap

INST03-01-70
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-01-80

3.1.3 Notes when installing or removing the part

3.1.3.1 Notes when handling the PCB
1. Check that the main edge connector of the PCB has linearity.

Sub-edge side

PCB

Main-edge side

Float of connector

OK (with linearity)
NG (without linearity)

Fig. 3.1.3.1-1 Checking connectors

2. When there is a float or a position gap in a connector, mark it with a label, etc.

PCB

Label

Fig. 3.1.3.1-2 Marking of defective connectors

INST03-01-80
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-01-90

3. Handle it as follows not to damage the main edge connector of the PCB.
(1) When holding the PCB, hold the middle part of the PCB with both hands.
Holding the main-edge side or sub-edge side of the PCB may cause a breakdown of the
PCB by dropping it under its weight or hitting it against something. Moreover, holding the
sub-edge side of the PCB may cause a loosening or disconnecting of the connector.

Right handling

PCB

Wrong handling

Sub-edge side A loosening or

disconnecting of the
PCB connector occurs

Main-edge side
Dropping / Hitting (Connector)

Fig. 3.1.3.1-3 Handling of the PCB (at maintenance)

(2) When moving the PCB, be careful enough not to make it hit a carrier, a table or a unit.

PCB

Carrier, table, etc.

Fig. 3.1.3.1-4 Handling of the PCB (at moving)

INST03-01-90
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-01-100

3.1.4 About the storage media used for installation / maintenance process
The media showed in following table are attached in storage system, in order to advance
installation, maintenance, and failure analysis smoothly. Please implement installation or collect
information according to the work procedure indicated in each section.

No. Media Description Installation Remarks

device
1 CD-ROM CD-R for micro program storage. CD-R Drive of Attached to the
Used for installation or micro program CE Laptop PC device
download in time of micro FC.
2 USB Memory The USB memory for configuration USB Connector Attached to the
information backup. of SVP device
Used for configuration information storage in
time of device configuration change.
3 USB Memory USB memory for collecting device dump USB Connector Attached to the
information. of SVP device
Used for collecting dump information in time
of failure analysis or operation investigation.

SVP-OPTION
SVP-BASIC

Rear View of DKC-0

USB Connector
(USB Port)

Front View of SVP

*1: Maintenance PC(Console PC) should be prepared by each maintenance

personnel, because it is not attached in the equipment as standard
equipment.

Fig. 3.1.4-1 Information Collection Device for each Media

INST03-01-100
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-01-110

3.1.5 Maintenance PC(Console PC)

3.1.5.1 Specifications for the Maintenance PC
A laptop PC that can be used as the Maintenance PC must meet specifications shown in Table
3.1.5.1-1.

Table 3.1.5.1-1 Maintenance PC Specifications

Specification
OS Windows XP / Windows Vista / Windows 7 / Windows 8
Disk Drive Available hard disk space: 500MB or upper
Display 1024 × 768 (XGA) or higher-resolution
1280 × 1024 (SXGA) Recommendation
DVD Drive Need
LAN Ethernet 10Base-T / 100Base-TX / 1000Base-T
USB Need

Maintenance PC

INST03-01-110
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-01-120

3.1.5.2 Installation Location of Maintenance PC

When using the Maintenance PC in the storage system, it is necessary to open the PC tray on the
rear door.
However, the Maintenance PC is needed to be prepared by each maintenance personnel, because it
is not attached in the equipment.

Rear Door

Maintenance PC

PC Tray

Rear View of
RACK-00

Fig. 3.1.5.2-1 Installation Location of PC Tray

INST03-01-120
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-01-130

3.1.5.3 Attachment / Removal Procedure of Maintenance PC

1. Attachment Procedure of Maintenance PC
a. Take out the LAN cable.
b. Loosen the screw on the back side of the rear door and slide the shipping stopper upward.
Then tighten the screw. (If the shipping stopper is already slid upward, this procedure is
not necessary.)

Shipping Stopper

Screw

Rear View of PC Tray

Rear Door

Fig. 3.1.5.3-1 Movement of Shipping Stopper

INST03-01-130
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-01-140

c. Open the PC tray so that it is in a horizontal position.

PC Tray

Rear View of
Rear Door

Fig. 3.1.5.3-2 Movement of PC Tray

INST03-01-140
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-01-150

d. Connect the power cable and LAN cable to the Maintenance PC.
e. Connect the LAN cable to CONSOLE port of the SVP-BASIC.
Connect the LAN cable to CONSOLE port of the SVP-OPTION when a trouble occurs on
SVP-BASIC. (Refer to Fig. 3.1.5.2-4.)
f. Connect the power cable to vacant connector of the PDU.
g. Power on the Maintenance PC.
h. When Windows is started, connect the PC to the SVP using the remote desktop function.

Rear Door

PDU PDU

Maintenance SVP-BASIC
PC

Power Cable SVP-BASIC CONSOLE

LAN Cable
Rear View of
To PDU
RACK-00

SVP-BASIC CONSOLE

50 – 60mm
25 – 30mm (*2)
(*2)

EMI Core

LAN Cable
(Wind the cable in EMI Core once.)

EMI Core (*1)

LAN Cable (*1)

*1: Components of DKC810I-CBXA.

*2: Recommended dimension.
Rear View of
RACK-00
Fig. 3.1.5.3-3 Connection of Cables (SVP-BASIC)
INST03-01-150
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-01-160

Rear Door

PDU PDU
Maintenance SVP-OPTION
PC

Power Cable SVP-OPTION CONSOLE

LAN Cable
Rear View of
To PDU
RACK-00

SVP-OPTION CONSOLE

50 – 60mm
25 – 30mm (*2)
(*2)

EMI Core

LAN Cable
(Wind the cable in EMI Core once.)

EMI Core (*1)

LAN Cable (*1)

*1: Components of DKC810I-CBXA.

*2: Recommended dimension.
Rear View of
RACK-00
Fig. 3.1.5.3-4 Connection of Cables (SVP-OPTION)

INST03-01-160
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-01-170

2. Removal Procedure of Maintenance PC

a. Quit the remote desktop function, and then power off the Maintenance PC.
b. Disconnect the power cable from the connector of the PDU. (Refer to Fig. 3.1.5.3-3 or Fig.
3.1.5.3-4.)
c. Disconnect the LAN cable from the CONSOLE port of the SVP-BASIC or SVP-OPTION.
d. Disconnect the power cable and LAN cable from the Maintenance PC.
e. Close and return the PC tray in place on the rear door. (Refer to Fig. 3.1.5.3-2.)
f. Store the LAN cable.

INST03-01-170
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-01-180

3.1.6 Notes when connecting the DEV interface cable

1. When connecting the DEV interface Cable, hold the connector with your fingers and insert it
into the PCB until it clicks. Do not turn the connector 90 degrees or more when inserting it into
the PCB. If the connector has to be turned 90 degrees or more, do not turn only the connector
but turn the connector and the cable together fitting the angle and connect it to the PCB.
The procedure of binding the DEV interface Cable to the rack frame must be done only after
the connector is connected.

PCB

Connector

Do not turn the connector

90 degrees or more.

Fig. 3.1.6-1 Connecting Connector

2. After inserting the DEV interface Cable into the blade, pull the connector gently to confirm
that the connector will not be disconnected.

Pull lightly.

Fig. 3.1.6-2 Confirming Fixation

INST03-01-180
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-01-190

3.1.7 Notes when connecting and disconnecting MFC cable

1. How to Connect Cable
a. Insert the connector into the PCB until it clicks, holding the edge of the handle of the
connector.

PCB
Connector

Edge

MFC Cable

Handle

Fig. 3.1.7-1 Connecting Cable

2. How to Disconnect Cable

a. Pull out the connector straight, putting your finger on the handle of the connector.
Note: Pulling out the MFC cable at an angle may get the edge of the connector caught in
the cable insertion opening on the PCB and damage the cable.

PCB

Connector
Pull out the MFC
MFC Cable cable straight from
the PCB.
Cable Insertion
Opening

Handle
MFC Cable

PCB Side View

Fig. 3.1.7-2 Disconnecting Cable

INST03-01-190
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-02-10

3.2 UNPACKING AND INSPECTION

Receiving and Inspection

Before unpacking the unit, check the physical condition of the packed unit.

1. Prior to unpacking, check the container for visible damage or any indication of excessive
shock, tilt or anything else abnormal during transportation and handling.

2. Obtain and check shipping manifest for missing units.

3. If anything abnormal is found, appropriate action should be taken before starting an

installation.

Unpacking Procedure

NOTE:
• Be very careful when handling the equipment.
• Do not drop the equipment from a height more than 5 mm (0.2in.) high.
• Floor unevenness must be less than 10 mm (0.4in.). Move slowly and lift the four screw jacks
at the bottom of each frame to the highest position to prevent contact with the ramp.

INST03-02-10
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-02-20

3.2.1 Unpacking
1. Card board crate overview is shown in Fig. 3.2.1-1.

For HDS
D W

Care Mark
(ISO Symbol)

Mebius-loop Mark

H
Shipping Mark

Caution Label

For HP
Logo D W
Size 186 × 203

Shipment Label

Horizontal ISO Symbol

Size 54 × 186

H
Mebius-loop Mark Logo
Size 186 × 203

Top Heavy Symbol

Size 250 × 300 Do not stack Mark
Size 435 × 355
Ramp/Slope Logo

CE Mark (40mm Characters) Horizontal ISO Symbol

GOST Mark (40 × 48) Size 54 × 186

Caution Mark Product Identification

Size 111 × 235 Label

Fig. 3.2.1-1 Card Board Crate Overview

INST03-02-20
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-03-10

3.3 Installation of Rack and Side Cover (DKC-F810I-RK42/SCOV/SCOVH)

CAUTION
Make sure that the equipment is moved by two or more persons.
Be sure to move the equipment by pushing it from the front face in the direction of
movement.
It is acceptable for two persons to move the equipment carefully from the front face and
rear face only when installing it. Do not push the equipment from the side face in
principle.
The front caster of the rack frame is not a rotary type but a fixed type not to incline the
equipment at over the tipping angle. Therefore, the equipment should not be rotated
quickly.

Moving the equipment normally

Move the rack frame only from the front face in principle.
Push the rack frame slowly with thumbs and the bases of them on both ends of the front face.
When changing moving direction, do so little by little in cooperation with an assistant instead
of changing moving direction quickly.
An assistant should not pull only the rear door strongly because doing so may cause the
deformation of the rear door.

Rear Door

40mm

40mm

Door Lock

40mm

Rear View of Front View of

Rack Frame Rack Frame

Fig. 3.3-1 Normal Movement Operation

INST03-03-10
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-03-20

Moving the equipment forward with limited space

When moving the equipment in the direction of the front of the rack frame, two persons must
cooperate. One pulls the front face of the rack frame in the direction of the installation location
and the other pushes the rear face of the rack frame with hands on the both ends of the rear
door at the position that is more than 50mm far from the door lock holding side covers. Do not
push the door lock directly.

Rear Door
40mm

40mm

Door Lock

40mm

Front View of
Rear View of Rack Frame
Rack Frame

Fig. 3.3-2 Forward Movement Operation

INST03-03-20
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-03-30

Moving the equipment in a lateral direction

When locating the equipment next to the equipment that was already installed, two persons
must cooperate. One pulls the front face of the rack frame and the other holds the side face of
the rack frame to move it.
Push the side face of the rack frame slowly with thumbs and bases of them on both edges of the
side cover of the middle rack. Do not push the side face when the equipment is in a sloping
place. Some of the equipment that has an upper center of gravity may fall down. Pushing the
central part of the side cover excluding the part within 40mm from the edge, or boundary part
of the side cover strongly may make the side cover caved in.

Do not push the boundary of side covers.

40mm from the side cover edge

40mm

40mm

Front View of
Rack Frame

Fig. 3.3-3 Lateral Movement Operation

INST03-03-30
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-03-40

Table 3.3-1 Parts List

No. Model Number Part Name Part No. Quantity Remarks
1 DKC-F810I-RK42 42U Rack Frame 1510159-C 1
Packing Work  3284263-D 1
Screw SB410N 8 Components of
Packing Work 
Packing Work  3283388-B 1
HEX Socket Bolt BS871N 2 Components of
Washer WP008N 4 Packing Work 
Nut NF008S 2
Packing Work  3283388-D 1
Screw SB406N 2 Components of
Lock Washer WT004N 2 Packing Work 
FG Cable 5524153-1 1
Packing Work  3287251-A 1
Rack Nut 5510146-1 4 Components of
Packing Work 
Packing Work  3287251-C 1
Screw SB510N 4 Components of
Packing Work 
Fix Plate 5546451-1 2 Fix Plate S
Loop Cable Tie 5552567-1 4
2 DKC-F810I-SCOV Side Cover 2853308-1 3
Side Cover 2853308-2 3
Screw SB406N 12
Screw SB432N 6
Washer 5513553-433 6
3 DKC-F810I- Side Cover 2854995-1 1 HITACHI Logotype
SCOVH Side Cover 2854995-2 1 HITACHI Logotype
Side Cover 2853308-2 1
Side Cover 2854995-3 1 HITACHI Logotype
Side Cover 2854995-4 1 HITACHI Logotype
Side Cover 2853308-1 1
Screw SB406N 12
Screw SB432N 6
Washer 5513553-433 6

INST03-03-40
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-03-50

3.3.1 Installation Procedure of Rack and Side Cover

1. Confirmation of Rack Frames Installation Location
a. Confirm the Rack Frames installation location and the Side Covers installation position.
b. When the Side Covers are needed to remove, remove the Side Covers referring to Fig.
3.3.1-5.

Table 3.3.1-1 Removal and Re-installation of Side Cover

Configuration RACK-12 RACK-11 RACK-10 RACK-00 RACK-01 RACK-02

2 Frames

Side Cover

3 Frames
Side Cover

4 Frames

5 Frames

6 Frames

INST03-03-50
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-03-60

2. Installation of Rack Frames

a. Move the Rack Frames to the installation location.
b. Line up the position between the rack frames to connect.
c. Adjust the height and the inclination of the Rack Frames by the four screw jacks in the
lower part of the Rack Frames. Ensure the clearance between the caster and the floor by
approximately 2.5mm when the height adjustment is performed. (One revolution of screw
jack = 2.5mm)

CAUTION
Caution of Over-Turning:
Work carefully for the height adjustment. A lack of balance that only one part rises too
much causes the over-turning. The height of the screw jacks shall be adjusted in 1/4
rotations evenly into the four places in order.
Caution of Breakage:
To prevent a breakage of the screw part of the screw jack, apply oil to the screw part in
advance of the operation.
Side to Side Height

Less than
2.5mm

Less than
2.5mm

Screw Jack

Tilt
Lateral Longitudinal
Screw Jack
(1 turn=2.5mm)

Caster

About 2.5mm
Floor

Less than 2.5mm Less than 2.5mm

Fig. 3.3.1-1 Adjusting Screw Jacks

INST03-03-60
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-03-70

3. Connection of Rack Frames

a. Remove the two screws from the front side of the Rack Frames to be connected and then
remove the two panels by moving them upward.

Rack Frame

Panel

Screw
Front View

Fig. 3.3.1-2 Removal of Panels

INST03-03-70
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-03-80

b. Connect the front of Rack Frames with the two fix plates and the eight screws.

Rack Frame

Fix Plate S

Screw
(SB410N)

Fix Plate S

Screw
(SB410N)

Front View

Fig. 3.3.1-3 Connection of Rack Frames (Front)

INST03-03-80
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-03-90

c. Connect the Rack Frames with the two HEX socket bolts, the four washers and the two
nuts.
d. Reinstall the two panels that is removed on the procedure a, and secure them with the two
screws. (Refer to Fig. 3.3.1-2.)

Rack Frame

HEX Socket Bolt

(BS871N)
Nut
(NF008S)

Washer
(WP008N)

Nut
(NF008S)

Washer
(WP008N)
HEX Socket Bolt
Rear View
(BS871N)

Fig. 3.3.1-4 Connection of Rack Frames (Rear)

INST03-03-90
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-03-100

4. Installation of Side Covers

CAUTION
Paying attention to falls:
Dropping a side cover may cause injury.
When installing or removing the side cover, hold the cover firmly with both hands and be
careful not to drop it on your feet. Make sure the side cover is hung on the hook of the
rack frame side when it is installed.
a. Install the three side covers by hanging them on the hooks of the rack frame side on the left
end of the storage system. Install the side covers from the lower sequentially.
Remove the side covers from the top sequentially when removing them.
b. Secure them with the six screws , the three screws  and the three washers.
c. Install the side covers on the right end of the Storage system as well as the left end.

Washer (WP004N)
Rack Frame
Screw 
(SB432N)

Hook

Washer (WP004N)
Screw 
(SB432N)

Washer (WP004N) Side Cover (L)

Screw 
(SB432N)

Screw 
(SB406N)

Screw 
(SB406N)
Hook

Screw 
Front View (SB406N)

Fig. 3.3.1-5 Attachment of Side Covers (SCOV)

INST03-03-100
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-03-110

Washer (WP004N)
Rack Frame
Screw 
(SB432N)

Hook

Washer (WP004N)
Screw 
(SB432N)

Washer (WP004N) Side Cover (L)

Screw 
(SB432N)

Screw 
(SB406N)

Screw 
(SB406N)
Hook

Screw 
Front View (SB406N)

Fig. 3.3.1-6 Attachment of Side Covers (SCOVH)

INST03-03-110
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-03-120

5. Attachment of FG cable
a. Attach the FG cable to the rear side of the racks, and secure it with the two screws and the
two lock washers.

RACK-02 RACK-01 RACK-00 RACK-10 RACK-11 RACK-12

A A A A A

Rear View

Detail A

Screw Lock Washer

(SB406N)

FG Cable
Rear View Rear View FG Cable

Fig. 3.3.1-7 Attachment of FG Cable

6. Return to the working table and do the rest of the work.

New Installation: INST02-10
Non-Disruptive Installation: INST02-40

INST03-03-120
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-04-10

3.4 Installation of Controller Chassis (DKC810I-CBXA, DKC-F810I-CBXB/CRF42/CRF3R/

BCH/BCP)

Notes when installing the DKC-F810I-CBXB:

Please note that an installation for the additional CHA, DKA, HDD and so on at the same time as
CBXB must be executed in steps as follows.

[Installation Sample]
Step1: Installation of Controller Chassis (DKC-F810I-CBXB) ............................. INST03-04-10
Step2: Installation of Processor Blade, HUB, Inter-Controller Connecting Kit/Cable and Cache
Memory (DKC-F810I-MP/HUB/MOD5/MFC5/MOD1J/MFC1J/CM16G/CM32G/
CPEX/BKMS/BKML/BMM128/BMM256) ............................................... INST03-07-10
Step3: Installation of Channel Adapter (DKC-F810I-8FC16/16FC8/16MS8/16ML8)
.................................................................................................................. INST03-08A-10
Step4: Installation of Drive Chassis (DKC-F810I-UBX/SBX/FBX) ..................... INST03-05-10
Step5: Installation of Disk Adapter, DEV Interface Cable and Drive .................... INST03-11-10

Operate the step 1 to 2 when installing only the additional CBXB.

For the installation of the additional CHA/DKA/HDD at the same time as the CBXB, operate
sequentially the step 3 to 5 after finishing the step 1 to 2.
Installing the additional parts for the step 3 to 5 at the same time as the step 1 to 2 is not possible.
Red LEDs for each part light when the parts mentioned above are installed at the same time.
In this case, remove the part at its related operation step and follow the correct procedures to
reinstall it.

INST03-04-10
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-04-20

Table 3.4-1 Parts List of DKC810I-CBXA

Item No. Part Name Part No. Quantity Remarks
1 DKC 1510157-B 1
2 Rear Stopper 3287250-1 1
3 Rear Stopper 3287250-2 1
4 WA Socket Bolt 3261959-516 4
5 WA Socket Bolt 3261959-408 4
6 Screw SB510N 10
7 HU Jumper 5521578-1 6 Maintenance Jumper
8 Rack Nut 5510146-1 14
9 Cable Duct 3287313-A 1
10 Cable Duct 3287313-B 1
11 Label (QTY) 3268905-1 1
12 Label (V/Hz/PH.) 3283091-1 2
13 S/R ASSY 3287308-A 1
14 Screw SB406N 2
15 Parts Location 5546147-1 1
16 Label (VCCI) 5545024-1 1 For HDS/HP
17 Label (BSMI-D3300) 3265644-4 1 For HDS
18 Label NOISE (FCC/CSA) 3283107-1 1 For HDS/HP
19 Label (KOREA-KC) 3284280-1 1 For HDS
20 Label (BSMI) 3269907-1 1 For HP
21 Label (BSMI NAME) 5552998-1 1
22 CE Address Label 2854907-1 1 For HDS
23 CE Address Label 2854907-2 1 For HP
24 Modular Plug Cord 5533144-5 1
25 EMI Core 5513535-1 3
26 Nameplate (HDS) 2854917-2 1 ITPD
(DKC810I-CBXA) 2855885-2 HICAM
2855885-502 HICEF

INST03-04-20
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-04-30

Table 3.4-2 Parts List of DKC-F810I-CBXB

Item No. Part Name Part No. Quantity Remarks
1 DKC 1510157-B 1
2 Rear Stopper 3287250-1 1
3 Rear Stopper 3287250-2 1
4 WA Socket Bolt 3261959-516 4
5 WA Socket Bolt 3261959-408 4
6 Screw SB510N 10
7 HU Jumper 5521578-1 6 Maintenance Jumper
8 Rack Nut 5510146-1 14
9 Cable Duct 3287313-A 1
10 Cable Duct 3287313-B 1
11 Label (QTY) 3268905-1 1
12 Label (V/Hz/PH.) 3283091-1 2
13 S/R ASSY 3287308-A 1
14 Screw SB406N 2
15 Parts Location 5546147-1 1
16 Label (VCCI) 5545024-1 1 For HDS/HP
17 Label (BSMI-D3300) 3265644-4 1 For HDS
18 Label NOISE (FCC/CSA) 3283107-1 1 For HDS/HP
19 Label (KOREA-KC) 3284280-1 1 For HDS
20 Label (BSMI) 3269907-1 1 For HP
21 Label (BSMI NAME) 5552998-1 1
22 CE Address Label 2854907-1 1 For HDS
23 CE Address Label 2854907-2 1 For HP
24 — — —
25 — — —
26 Nameplate (HDS) 2854917-3 1 ITPD
(DKC-F810I-CBXB) 2855885-3 HICAM
2855885-503 HICEF

INST03-04-30
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-04-40

Table 3.4-3 Parts List of DKC-F810I-CRF42

Item No. Part Name Part No. Quantity Remarks
101 Rail 3287119-2 2
102 Rack Nut 5510146-1 8
103 WA Socket Bolt 3261959-510 8

Table 3.4-4 Parts List of DKC-F810I-CRF3R

Item No. Part Name Part No. Quantity Remarks
201 Rail L 3287401-A 1
202 Rail R 3287401-B 1

Table 3.4-5 Parts List of DKC-F810I-BCH

Item No. Part Name Part No. Quantity Remarks
301 Bezel (8U) ASSY 3287331-B 1
302 Bezel (2U) ASSY 3287332-A 1
303 Bezel Bracket (2U) 5555016-A 2
304 Bezel Bracket R 5555017-A 1
305 Side Cover L 2854990-101 1
306 Side Cover R 2854991-1 1
307 Lower Cover 3287273-1 1
308 Bezel Bracket L 3287274-1 1
309 Sheet (BLIND) 5555005-1 1
310 Screw SB305N 6
311 TAG INST 5557047-A 1 Key

Table 3.4-6 Parts List of DKC-F810I-BCP

Item No. Part Name Part No. Quantity Remarks
301 HP Bezel (8U) ASSY 3290503-B 1
302 HP Bezel (2U) ASSY 3290504-A 1
303 Bezel Bracket (2U) 5555016-A 2
304 Bezel Bracket R 5555017-A 1
305 Side Cover L 2854990-2 1
306 Side Cover R 2854991-2 1
307 Lower Cover 3287273-1 1
308 Bezel Bracket L 3287274-1 1
309 Sheet (BLIND) 5557315-1 1
310 Screw SB305N 6
311 TAG INST 5557047-A 1 Key

INST03-04-40
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-04-50

3.4.1 Installation Procedure of Controller Chassis

1. Installing the rails (If the rails are already installed, this installation procedure is not required.)

EIA units and intervals of mounting holes of 19-inch rack frame conforming to EIA standard
• A unit (U) space conforming to EIA standard is 19 inches wide and 44.45 mm high as shown
in the figure below.
• The boundary of the unit falls on the middle of the interval of 12.7 mm.
• Universal intervals: Repeat of 44.45 mm (15.875 mm + 15.875 mm + 12.7 mm)
Wide intervals: Repeat of 44.45 mm (31.75 mm + 12.7 mm)
Maximum number of mountable unit spaces: 42U

12.7mm Unit Boundary

15.875mm 1U = 44.45mm
31.75mm
15.875mm 1 unit (EIA)
12.7mm Unit Boundary

Some types of rack frame do not have this hole.

Rack frame with the holes: Universal interval
Rack frame without the holes: Wide interval
Fig. 3.4.1-1 Attachment Hole Size of Rack

INST03-04-50
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-04-60

The addresses are given as 1, 2, 3, and so on counted from the bottom of the rack frame.
The following figure shows a layout example of installing Controller Chassis in 42 units rack
frame. However, installing positions of Controller Chassis may differ according to the
construction within the rack frame.

Addresses of installation The height from the bottom

positions boundary of number 1U

Unit boundary 1866.90mm

42U
Unit boundary 1822.45mm
Unit boundary 41U
40U
1778.00mm
Unit boundary 1733.55mm
39U
Unit boundary 1689.10mm
38U
Unit boundary 1644.65mm
37U
Unit boundary 1600.20mm
Unit boundary 36U
35U 1555.75mm
Unit boundary 1511.30mm
Unit boundary 34U
1466.85mm
33U
Unit boundary 1422.40mm
Unit boundary 32U
31U 1377.95mm
Unit boundary 1333.50mm
Unit boundary 30U
29U
1289.05mm
Unit boundary 1244.60mm
28U
Unit boundary 1200.15mm
27U
Unit boundary 1155.70mm
26U
Unit boundary 1111.25mm
25U
Unit boundary 1066.80mm
24U
Unit boundary 1022.35mm
23U
Unit boundary 977.90mm
22U
Unit boundary
21U
933.45mm
Unit boundary
20U
889.00mm
Unit boundary 844.55mm
19U
Unit boundary
18U
800.10mm
Unit boundary 755.65mm
17U
Unit boundary 711.20mm
DKC 16U (10 EIA Units)
Unit boundary 666.75mm
15U
Unit boundary 622.30mm
14U
Unit boundary
13U
577.85mm
Unit boundary 533.40mm
12U
Unit boundary
11U
488.95mm
Unit boundary
10U
444.50mm
Unit boundary 400.05mm
9U
Unit boundary
8U
355.60mm
Unit boundary 7U
311.15mm
Unit boundary DKC 6U (10 EIA Units)
266.70mm
Unit boundary 5U
222.25mm
Unit boundary 177.80mm
4U
Unit boundary 3U 133.35mm
Unit boundary 2U 88.90mm
Unit boundary 44.45mm
1U
Unit boundary
(Starting point of
height direction)

Fig. 3.4.1-2 Whole Layout of Installation Position Addresses

INST03-04-60
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-04-70

1-1 In the Case of Standard Rails

a. On the right side of the installation location in the rack frame, align the round holes of the
rail with those of the rack frame and insert the rack nuts (at four places in total in front and
rear).
b. Fasten the rail to the rack frame using the WA socket bolts (at two places each on the front
and rear sides).
c. Install the rail to the left side of the rack frame in the same way.

Rack Nut (Item No. 102)

Rack Frame
(Front View)

WA Socket Bolt
(Item No. 103)

Rail
(Item No. 101)

WA Socket Bolt
(Item No. 103)

Rack Nut

Unit Boundary
1 Unit (1 EIA)
Unit Boundary
Bottom Unit of
Installation Position
Unit Boundary

When you shift the rail a little upward from the position where the bottom edge of
the rail is aligned with the lower boundary line of the installation position address
(boundary of a unit), the round holes on the rail are exactly aligned with the holes
on the rack frame.

Fig. 3.4.1-3 Attachment of Rails

INST03-04-70
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-04-80

1-2 In the Case of Adjustable Rails

a. Remove the four screws and four washers from the front and rear side of the rail.

Washer
Screw
(SB516N)

Guide Pin

Washer

Rail R Screw
(Item No. 202) (SB516N)

Guide Pin
Front View

Fig. 3.4.1-4 Removal of Screws and Washers

INST03-04-80
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-04-90

b. If the insertion holes on the rack frame are square, reinstall the two Positioning Plates on
the front and rear side of the rail.
If the insertion holes on the rack frame are round, go to Procedure c.
b-1 Remove the four screws from the front and rear side of the rail and remove the two
Positioning Plates.
b-2 Turn the two Positioning Plates 180 degrees and reinstall and secure them to the rail with
the four screws.
c. Do the same procedure for the left rail.
Screw
(SC410N) Positioning Plate

Rail R
(Item No. 202)

Positioning Plate

Guide Pin
180 Degree Turn

Screw
(SC410N)

Guide Pin
Front View

Positioning Plate 180 Degree Turn

Screw
(SC410N)

Positioning Plate

Screw
(SC410N)

Front View

Fig. 3.4.1-5 Reinstallation of Positioning Plates

INST03-04-90
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-04-100

d. Loosen the six screws on the side of the rail and adjust the length of the rail. (See Fig.
3.4.1-6 or Fig. 3.4.1-7.)
If the length of the rail does not become the same as the width of the rack frame even after
the screws are loosen, remove the six screws and adjust the length again. Then tighten the
six screws in the four holes on both sides and the two holes near the Guide Pins.
e. Fit the Guide Pins (or the edges of the Positioning Plate) into the holes on the right front
side of the rack frame and tighten the two washers and two screws temporarily.
f. Fit the Guide Pins (or the edges of the Positioning Plate) into the holes on the right rear
side of the rack frame and tighten the two washers and two screws temporarily.
g. Fully tighten the four screws that were tightened temporarily in Procedure e and f, pressing
the rail against the side of the rack frame.
h. Tighten the six screws on the rail.
i. Install the rail to the left side of the rack frame in the same way.

Screw
(SB516N)
B
Rack Frame
(Front)
Washer

Guide Pin

Guide Pin
Washer
Rail R
(Item No. 202)
A
Screw
Screw
(SB408N)
(SB516N)
Guide Pin

Unit Boundary Unit Boundary

Guide Pin Guide Pin
Unit Boundary Unit Boundary
Washer Washer
Unit Boundary Unit Boundary
1 Unit Screw Screw 1 Unit
Unit Boundary Unit Boundary
(*1) Rail Rail (*1)
Unit Boundary Unit Boundary
Guide Pin Guide Pin
Rear View (Detail of B) Front View (Detail of A)
*1: Bottom Unit of Installation Position

Fig. 3.4.1-6 Attachment of Adjustable Rails (in the Case of Round Insertion Holes.)

INST03-04-100
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-04-110

Screw
(SB516N)
B

Rack Frame
(Front)
Washer

Guide Pin

Guide Plate
Washer
Rail R
(Item No. 202)

A
Screw
(SB408N) Screw
(SB516N)
Guide Plate

Unit Boundary Unit Boundary

Guide Plate Guide Plate
Unit Boundary Unit Boundary
Washer Washer
Unit Boundary Unit Boundary
1 Unit Screw Screw 1 Unit
Unit Boundary Unit Boundary
(*1) Rail Rail (*1)
Unit Boundary Unit Boundary
Guide Plate Guide Plate
Rear View (Detail of B) Front View (Detail of A)

*1: Bottom Unit of Installation Position

Fig. 3.4.1-7 Attachment of Adjustable Rails (in the Case of Square Insertion Holes.)

INST03-04-110
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-04-120

2. Installing rack nuts

a. Fit the two rack nuts to each of the right and left beams on the front side of the rack frame.
b. Fit the four rack nuts to each of the right and left beams on the rear side of the rack frame.

Area of Controller Chassis

10th U
9th U
Lower hole 8th U Lower hole
of 8th Unit 7th U of 8th Unit
10 Units
6th U
5th U
Lower hole 4th U Lower hole
of 4th Unit 3rd U of 4th Unit
2nd U
1st U (*1)

Front View of Rack Frame

Upper hole Upper hole

of 9th Unit 10th U of 9th Unit
9th U
8th U
Upper hole 7th U Upper hole
of 8th Unit 6th U of 8th Unit 10 Units
5th U
Lower hole 4th U Lower hole
of 5th Unit 3rd U of 5th Unit
2nd U
Lower hole 1st U (*1) Lower hole
of 4th Unit of 4th Unit
Rear View of Rack Frame

*1: Bottom Unit of Installation Position

Rack Frame
(Front Side)

Rack Nut
(Item No. 8)

Fig. 3.4.1-8 Attachment of Rack Nuts

INST03-04-120
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-04-130

3. Installing the DKC

CAUTION
Paying attention to falls:
Work carefully because the mass of the single DKC is about 140 kg.
a. Install the DKC on the Rack frame referring to mounting procedure using the special lifter.
(See INST03-15-10 through 40.)
b. When the bezels are not installed in the DKC, secure the front of the DKC with the four
screws.
When the bezels are installed in the DKC, go to Procedure c. (The DKC is secured with the
screws and bezel brackets in the procedure described later.)

Rail

Screw (SB510N)
(Item No. 6)

Front View of
Rack Frame
Rail

DKC
(Item No. 1)

Screw (SB510N)
(Item No. 6)

Fig. 3.4.1-9 Installing DKC

INST03-04-130
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-04-140

c. Attach the two rear stoppers on the rear side of DKC and tighten the WA socket bolts.

Rear Stopper
(Item No. 2)

WA Socket Bolt
(Item No. 5)

WA Socket Bolt Rear Stopper

(Item No. 4) (Item No. 3)

Rear View of WA Socket Bolt

DKC (Item No. 5)

WA Socket Bolt
(Item No. 4)

Fig. 3.4.1-10 Attachment of Stoppers

INST03-04-140
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-04-150

d. Attach the two cable ducts on the rear side of rack and tighten the four screws.

Cable Duct
(Item No. 10)

Screw (SB510N)
(Item No. 6)

Screw (SB510N)
(Item No. 6)

Rear View of
Cable Duct
Rack
(Item No. 9)

Fig. 3.4.1-11 Attachment of Cable Ducts

e. Attach the S/R ASSY on the rear side of rack and tighten the two screws.

Screw (SB406N)
(Item No. 14)

S/R ASSY
Rear View of (Item No. 13)
Rack

Fig. 3.4.1-12 Attachment of S/R ASSY

INST03-04-150
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-04-160

4. Storage of parts
a. Put the modular plug cord, three EMI cores, and Parts Location in the storage bag.

Modular Plug Cord

(Item No. 24) (*1)

EMI Core
(Item No. 25) (*1)

Parts Location
(Item No. 15) *1: For DKC-F810I-CBXB, these
parts are unattached.

Fig. 3.4.1-13 Storage of Parts

INST03-04-160
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-04-170

5. Jumper Setting
NOTE: Be sure to wear your wrist strap and attach to ground prior to performing the
following work. This will ensure that the IC and LSI on the PCB are protected from
static electricity.
a. Set the jumpers (JP1 and JP2) in the SSVPMN.

CAUTION
A serious failure occurs if a wrong setting is made.
Operate very carefully referring to the setting table not to make a mistake in the setting.
Table 3.4.1-1 Installation of Jumper in SSVPMN
Function Name Jumper No. Settings Remarks
SSVPMN JP1 Set the MODULE ID of the DKC equipped For SSVPMN-0
JP1
(MODULE ID) with SSVPMN. 12 10
• MODULE0 ... SSVPMN-0 (DKC-0) 9 7
Plug the jumper cap on #1, 4, 7, 10. 6 4 Jumper
3 1

• MODULE1 ... SSVPMN-1 (DKC-1) For SSVPMN-1

JP1
Plug the jumper cap on #3, 6, 9, 12. 12 10
9 7
6 4 Jumper
3 1

JP2 Power on the storage system by switching Disable Setting

JP2
(AUTOPSON) PS ON/PS OFF after turn on the AC 4 3 Jumper
power. (Initial setting) 2 1
Set only the SSVPMN-0 in the Jumper.
(#3-4) No setting of SSVPMN-1 is needed.
The storage system is powered on Enable Setting
JP2
automatically after turn on the AC power. 4 3
Set only the SSVPMN-0 in the Jumper. 2 1 Jumper
(#1-2) No setting of SSVPMN-1 is needed.
SSVPMN-0

Rear View of DKC-0

SSVPMN-1 JP2
JP1

Top View of SSVPMN

Rear View of DKC-1

Fig. 3.4.1-14 Installation of Jumper in SSVPMN

INST03-04-170
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-04-180

6. Labeling
a. Attach the label (V/Hz/PH.) on the rear side of DKC. The label (V/Hz/PH.) should be
selected among the sheet of label (V/Hz/PH.) corresponding to the operating voltage,
frequency and phase.
When the corresponding operating voltage, frequency and phase are not exist, write the
values in the label that is not listed the value of the operating voltage, frequency and phase.
b. Attach the label (BSMI NAME) on the rear side of DKC.

Label (V/Hz/PH.) Label (BSMI NAME)

(Item No. 12) (Item No. 21)

Rear View of DKC

Label (V/Hz/PH.)

T H I S M AC H IN E I S W I R ED F O R
AC V Hz PH.
DIESE MASCHINE IST FUR DEN Voltage, Frequency and Phase
BETRIEB BEI V Hz PH.
ESTA MAQUINA ESTA CABLEADA
PARA CA V Hz PH.

Fig. 3.4.1-15 Attachment of Labels

INST03-04-180
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-04-190

c. Attach the labels and nameplate on the front side of DKC. (Refer to Fig. 3.4.1-16 or Fig.
3.4.1-17.)

For HDS

Nameplate
(Item No. 26)
CE Address Label
(Item No. 22)

Label (VCCI)
(Item No. 16)

A B

Label NOISE
(FCC/CSA)
Label (BSMI-D3300)
(Item No. 18)
(Item No. 17)

Front View of DKC

Label (KOREA-KC)
(Item No. 19)

Viewed from A Viewed from B

Fig. 3.4.1-16 Attachment of Labels and Nameplate (For HDS)

INST03-04-190
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-04-200

For HP

Nameplate
(Item No. 26)
CE Address Label
(Item No. 23)

Label (VCCI)
(Item No. 16)

A B

Label NOISE
(FCC/CSA)
Label (BSMI) (Item No. 18)
(Item No. 20)
Front View of DKC

Viewed from A Viewed from B

Fig. 3.4.1-17 Attachment of Labels and Nameplate (For HP)

INST03-04-200
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-04-210

3.4.2 Installation Procedure of Bezel

1. When you need to install Controller Chassis Bezel (DKC-F810I-BCH), attach the bezels to the
front side of DKC.
When you do not need to install Controller Chassis Bezel (DKC-F810I-BCH), go to procedure
3.

a. Secure the Bezel Bracket L and the Bezel Bracket R to the front of the DKC with the four
screws.
b. Secure the two Bezel Brackets (2U) with the four screws.
c. Secure the Lower Cover to the Bezel Bracket L and the Bezel Bracket R with the two
screws.
d. Install the Side Cover L in the Bezel Bracket L on the front left side of the DKC.
e. Install the Side Cover R in the Bezel Bracket R on the front right side of the DKC.

Bezel Bracket (2U)

(Item No. 303)
DKC

Screw (SB305N)
(Item No. 310)
Bezel Bracket (2U)
Bezel Bracket L (Item No. 303)
(Item No. 308)

Screw (SB510N)
Screw (SB305N)
(Item No. 6)
(Item No. 310)

Screw (SB510N)
(Item No. 6)

Screw (SB305N)
(Item No. 310)

Side Cover L Lower Cover

(Item No. 305) (Item No. 307)

Bezel Bracket R
Screw (SB305N) (Item No. 304)
(Item No. 310)

Front View of Side Cover R

(Item No. 306)
RACK

Fig. 3.4.2-1 Attachment of Parts

INST03-04-210
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-04-220

2. Attachment of Bezels
a. When installing the bezels to the DKC-F810I-CBXB, attach the Sheet (BLIND) to the
DKC Bezel (2U).
When installing the bezels to the DKC810I-CBXA, go to Procedure b.

For HDS For HP

Sheet (BLIND) Sheet (BLIND)

(Item No. 309) (Item No. 309)

DKC Bezel (2U) DKC Bezel (2U)

(Item No. 302) (Item No. 302)

Fig. 3.4.2-2 Attachment of Sheet (BLIND)

b. Hold the side of bezel with both hands.

c. After making the hooks of the bezel engaged, press the bezel against the main body until it
is stopped.

Ball Catch
DKC

Ball Catch

DKC Bezel (2U)

(Item No. 302)

Fig. 3.4.2-3 Attachment of DKC Bezel (2U)

INST03-04-220
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-04-230

d. Unlock the bezel with the key, and hold the key and bottom of bezel with your both hands.
e. Insert the tabs on the left front side of the chassis into the tab holes on the bezel ().
f. Fix the bezel by pressing the right side of the bezel to engage it with the ball catch on the
front side of the chassis ().
g. Lock the bezel with the key ().

Tab

Tab Hole

 Ball Catch




Key
The state in which the slit of the (Item No. 311)
keyhole is aligned with the mark.
(The key can be inserted or pulled out
in this state.)
DKC Bezel (8U)
Keyhole (Item No. 301)
To lock

Fig. 3.4.2-4 Attachment of DKC Bezel (8U)

3. Return to the working table and do the rest of the work.

New Installation: INST02-10
Non-Disruptive Installation: INST02-40

INST03-04-230
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-10

3.5 Installation of Drive Chassis (DKC-F810I-UBX/SBX/FBX/SBBRAL/BUH/BUP/FMDRAL/

BFH/BFP)
Do this work after confirming the below-mentioned notes.

NOTICE: • Confirm Control Chassis (DKC810I-CBXA/DKC-F810I-CBXB) is installed.

• Confirm drive is not installed. De-install drive if drive is installed.

3.5.1 Rough time of installation

Rough time of RAID Group installation becomes addition of the following A, B, C, D, and E.

Table 3.5.1-1 Rough time of installation

Process time NOTE
A Chassis setting time SBX/UBX: 90min
FBX: 50min
B HDD setting time 1min / 1HDD
C Micro code overhead for Path 90sec × (The number of existing chassis + number *1
initialization of increase chassis)
D Micro code over head for 20sec × (number of increase HDD) *1
HDD spin up
E LDEV Formatting time Refer to THEORY 3.5

*1: Twice time at the high performance model are possessed.

INST03-05-10
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-20

3.5.2 Parts List

Table 3.5.2-1 Parts List of DKC-F810I-UBX

Item No. Part Name Part No. Quantity Remarks
1 LFF SBB 5552746-A 8 HDU
2 Loop Cable Tie 5552567-1 16
3 Label (DKU-BOX) 3287114-1 3
4 Label (VCCI) 5545024-1 8 For HDS/HP
5 Label (BSMI-D3300) 3265644-4 8 For HDS
6 Label (BSMI) 3269907-1 8 For HP
7 Label-Noise (FCC/CSA) 3283107-1 8 For HDS/HP
8 Label (KOREA-KC) 3284280-1 8 For HDS
9 Label (BSMI NAME) 5552998-1 8 For HDS/HP
10 Label (UL3) 5515795-1 1 For HDS/HP
11 CE Address Label 2854907-1 8 For HDS
12 CE Address Label 2854907-2 8 For HP
13 Label Location (HDU) 5550568-1 2 Label Location 
14 Label Location (HDU) 5550568-2 2 Label Location 
15 Label Location (HDU) 5550568-3 2 Label Location 
16 Label Location (HDU) 5550568-4 2 Label Location 
17 Label Location (HDU) 5550568-5 2 Label Location 
18 Label Location (HDU) 5550568-6 2 Label Location 
19 Label Location (HDU) 5550568-7 2 Label Location 
20 Label Location (HDU) 5550568-8 2 Label Location 
21 Side Bezel 2853845-1 8
22 Location Label (HDD) 5557125-1 2
23 Tag (HDD LABEL) 5557126-1 2

INST03-05-20
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-30

Table 3.5.2-2 Parts List of DKC-F810I-SBX

Item No. Part Name Part No. Quantity Remarks
1 SFF SBB 5552745-A 8 HDU
2 Loop Cable Tie 5552567-1 16
3 Label (DKU-BOX) 3287114-1 3
4 Label (VCCI) 5545024-1 8 For HDS/HP
5 Label (BSMI-D3300) 3265644-4 8 For HDS
6 Label (BSMI) 3269907-1 8 For HP
7 Label-Noise (FCC/CSA) 3283107-1 8 For HDS/HP
8 Label (KOREA-KC) 3284280-1 8 For HDS
9 Label (BSMI NAME) 5552998-1 8 For HDS/HP
10 Label (UL3) 5515795-1 1 For HDS/HP
11 CE Address Label 2854907-1 8 For HDS
12 CE Address Label 2854907-2 8 For HP
13 Label Location (HDU) 5550568-1 2 Label Location 
14 Label Location (HDU) 5550568-2 2 Label Location 
15 Label Location (HDU) 5550568-3 2 Label Location 
16 Label Location (HDU) 5550568-4 2 Label Location 
17 Label Location (HDU) 5550568-5 2 Label Location 
18 Label Location (HDU) 5550568-6 2 Label Location 
19 Label Location (HDU) 5550568-7 2 Label Location 
20 Label Location (HDU) 5550568-8 2 Label Location 
21 Side Bezel 2853845-1 8

INST03-05-30
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-40

Table 3.5.2-3 Parts List of DKC-F810I-FBX

Item No. Part Name Part No. Quantity Remarks
1 FMU Chassis 3286597-A 4 FMU
2 Loop Cable Tie 5552567-1 8
3 Label Location (HDU) 5550568-1 2 Label Location 
4 Label Location (HDU) 5550568-2 2 Label Location 
5 Label Location (HDU) 5550568-3 2 Label Location 
6 Label Location (HDU) 5550568-4 2 Label Location 
7 Label Location (HDU) 5550568-5 2 Label Location 
8 Label Location (HDU) 5550568-6 2 Label Location 
9 Label Location (HDU) 5550568-7 2 Label Location 
10 Label Location (HDU) 5550568-8 2 Label Location 
11 Label (DKU-BOX) 3287114-1 3
12 Label (VCCI) 5545024-1 4 For HDS/HP
13 Label (BSMI-D3300) 3265644-4 4 For HDS
14 Label (BSMI) 3269907-1 4 For HP
15 Label-Noise (FCC/CSA) 3283107-1 4 For HDS/HP
16 Label (KOREA-KC) 3287464-1 4 For HDS
17 Label (BSMI NAME) 5552998-1 4 For HDS/HP
18 CE Address Label 2854907-1 4 For HDS
19 CE Address Label 2854907-2 4 For HP

INST03-05-40
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-50

Table 3.5.2-4 Parts List of DKC-F810I-BUH

Item No. Part Name Part No. Quantity Remarks
101 Bezel (8U) ASSY 3287331-A 2
102 Bezel Bracket R 5555018-A 2
103 Side Cover L 2854990-101 2
104 Side Cover R 2854991-1 2
105 Bezel Bracket L 3287271-1 2
106 Nut Plate L 5552831-1 4
107 Nut Plate R 5552831-2 4
108 Screw SB305N 16
109 TAG INST 5557047-A 2 Key

Table 3.5.2-5 Parts List of DKC-F810I-BUP

Item No. Part Name Part No. Quantity Remarks
101 HP Bezel (8U) ASSY 3290503-A 2
102 Bezel Bracket R 5555018-A 2
103 Side Cover L 2854990-2 2
104 Side Cover R 2854991-2 2
105 Bezel Bracket L 3287271-1 2
106 Nut Plate L 5552831-1 4
107 Nut Plate R 5552831-2 4
108 Screw SB305N 16
109 TAG INST 5557047-A 2 Key

Table 3.5.2-6 Parts List of DKC-F810I-SBBRAL

Item No. Part Name Part No. Quantity Remarks
201 Slide Rail 5552699-3 16
202 Screw (M5) — 32 (*1)
203 Screw (M4) — 32 (*1)
204 Nut (M4) — 32 (*1)

*1: Appended goods of Item No.2

INST03-05-50
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-60

Table 3.5.2-7 Parts List of DKC-F810I-BFH

Item No. Part Name Part No. Quantity Remarks
301 Bezel (8U) NF ASSY 3287459-A 1 DKU Bezel
302 Bezel Bracket (NF) R 5557048-A 1 Bezel Bracket R
303 Side Cover L 2854990-101 1
304 Side Cover R 2854991-1 1
305 Bezel Bracket (NF) L 3287399-1 1 Bezel Bracket L
306 Nut Plate (NF) L 5555348-1 2 Nut Plate L
307 Nut Plate (NF) R 5555348-2 2 Nut Plate R
308 Screw SB305N 8
309 TAG INST 5557047-A 1 Key

Table 3.5.2-8 Parts List of DKC-F810I-BFP

Item No. Part Name Part No. Quantity Remarks
301 HP Bezel (8U) NF ASSY 3290508-A 1 DKU Bezel
302 Bezel Bracket (NF) R 5557048-A 1 Bezel Bracket R
303 Side Cover L 2854990-2 1
304 Side Cover R 2854991-2 1
305 Bezel Bracket (NF) L 3287399-1 1 Bezel Bracket L
306 Nut Plate (NF) L 5555348-1 2 Nut Plate L
307 Nut Plate (NF) R 5555348-2 2 Nut Plate R
308 Screw SB305N 8
309 TAG INST 5557047-A 1 Key

Table 3.5.2-9 Parts List of DKC-F810I-FMDRAL

Item No. Part Name Part No. Quantity Remarks
401 Rail L 2854516-A 4
402 Rail R 2854516-B 4
403 Packing Work  3286610-A 4
404 Screw 3261898-512 16 (*1)
405 Packing Work  3286610-B 4
406 Square Spacer 5550614-1 24 (*2)

*1: Appended goods of Item No.403

*2: Appended goods of Item No.405

INST03-05-60
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-70

3.5.3 Installation Procedure of Drive Chassis (DKC-F810I-UBX/SBX)

1. Confirmation of installation position

EIA units and intervals of mounting holes of 19-inch rack frame conforming to EIA standard
• A unit (U) space conforming to EIA standard is 19 inches wide and 44.5 mm high as shown
in the figure below.
• The boundary of the unit falls on the middle of the interval of 12.7 mm.
• Universal intervals: Repeat of 44.45 mm (15.875 mm + 15.875 mm + 12.7 mm)
Wide intervals: Repeat of 44.45 mm (31.75 mm + 12.7 mm)
Maximum number of mountable unit spaces: 42

12.7mm Unit Boundary

15.875mm 1U = 44.45mm
31.75mm
15.875mm 1 unit (EIA)
12.7mm Unit Boundary

Some types of rack frame do not have this hole.

Rack frame with the holes: Universal interval
Rack frame without the holes: Wide interval
Fig. 3.5.3-1 Attachment Hole Size of Rack

INST03-05-70
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-80

The addresses are given as 1, 2, 3, and so on counted from the bottom of the rack frame.
The following figures show a layout example of installing Drive chassis in 42 units rack frame.
However, installing positions of Drive chassis may differ according to the construction within
the rack frame.

Addresses of installation The height from the bottom

positions boundary of number 1U

Unit boundary 1866.90mm

42U
Unit boundary 1822.45mm
41U
Unit boundary 1778.00mm
40U
Unit boundary
39U
1733.55mm
Unit boundary 1689.10mm
38U
Unit boundary 1644.65mm
Unit boundary Area of 37U
1600.20mm
Unit boundary DKU 36U (16 EIA units)
35U 1555.75mm
Unit boundary (Option 2) 1511.30mm
34U
Unit boundary 1466.85mm
33U
Unit boundary 1422.40mm
Unit boundary 32U
31U 1377.95mm
Unit boundary 1333.50mm
Unit boundary 30U
1289.05mm
Unit boundary 29U
28U
1244.60mm
Unit boundary 1200.15mm
27U
Unit boundary 1155.70mm
26U
Unit boundary 1111.25mm
25U
Unit boundary 1066.80mm
24U
Unit boundary 1022.35mm
23U
Unit boundary 977.90mm
22U
Unit boundary 933.45mm
Unit boundary
Area of 21U
889.00mm
DKU 20U (16 EIA units)
Unit boundary 844.55mm
(Option 1) 19U
Unit boundary
18U
800.10mm
Unit boundary 755.65mm
17U
Unit boundary 711.20mm
16U
Unit boundary 666.75mm
15U
Unit boundary 622.30mm
14U
Unit boundary
13U
577.85mm
Unit boundary 533.40mm
12U
Unit boundary
11U
488.95mm
Unit boundary
10U
444.50mm
Unit boundary
9U 400.05mm
Unit boundary 355.60mm
8U
Unit boundary 311.15mm
7U
Unit boundary
6U
266.70mm
Unit boundary 5U
222.25mm
Unit boundary 177.80mm
4U
Unit boundary 3U
133.35mm
Unit boundary 2U 88.90mm
Unit boundary 44.45mm
1U
Unit boundary
(Starting point of
height direction)

RACK-00/10

Fig. 3.5.3-2 Whole Layout of Installation Position Addresses (RACK-00/10)

INST03-05-80
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-90

Addresses of installation The height from the bottom

positions boundary of number 1U

Unit boundary 1866.90mm

42U
Unit boundary 1822.45mm
41U
Unit boundary 1778.00mm
40U
Unit boundary
39U
1733.55mm
Unit boundary 1689.10mm
38U
Unit boundary 1644.65mm
37U
Unit boundary 1600.20mm
Unit boundary 36U
35U 1555.75mm
Unit boundary 1511.30mm
34U
Unit boundary 1466.85mm
33U
Unit boundary 1422.40mm
Unit boundary 32U
31U 1377.95mm
Unit boundary 1333.50mm
Unit boundary 30U
1289.05mm
Unit boundary Area of 29U
28U
1244.60mm
Unit boundary DKU (16 EIA units) 1200.15mm
(Option 4) 27U
Unit boundary 1155.70mm
26U
Unit boundary 1111.25mm
25U
Unit boundary 1066.80mm
24U
Unit boundary 1022.35mm
23U
Unit boundary 977.90mm
22U
Unit boundary
21U
933.45mm
Unit boundary 889.00mm
20U
Unit boundary 844.55mm
19U
Unit boundary
18U
800.10mm
Unit boundary 755.65mm
17U
Unit boundary 711.20mm
16U
Unit boundary 666.75mm
15U
Unit boundary 622.30mm
14U
Unit boundary
13U
577.85mm
Unit boundary Area of 533.40mm
DKU 12U (16 EIA units)
Unit boundary
11U
488.95mm
Unit boundary (Option 3) 444.50mm
10U
Unit boundary
9U 400.05mm
Unit boundary 355.60mm
8U
Unit boundary 311.15mm
7U
Unit boundary
6U
266.70mm
Unit boundary 5U
222.25mm
Unit boundary 177.80mm
4U
Unit boundary 3U
133.35mm
Unit boundary 2U 88.90mm
Unit boundary 44.45mm
1U
Unit boundary
(Starting point of
height direction)

RACK-01/11

Fig. 3.5.3-3 Whole Layout of Installation Position Addresses (RACK-01/11)

INST03-05-90
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-100

Addresses of installation The height from the bottom

positions boundary of number 1U

Unit boundary 1866.90mm

42U
Unit boundary 1822.45mm
41U
Unit boundary 1778.00mm
40U
Unit boundary
39U
1733.55mm
Unit boundary 1689.10mm
38U
Unit boundary 1644.65mm
37U
Unit boundary 1600.20mm
Unit boundary 36U
35U 1555.75mm
Unit boundary 1511.30mm
34U
Unit boundary 1466.85mm
33U
Unit boundary 1422.40mm
Unit boundary 32U
31U 1377.95mm
Unit boundary 1333.50mm
Unit boundary 30U
Area of 1289.05mm
Unit boundary 29U
DKU 28U
1244.60mm
Unit boundary 1200.15mm
Unit boundary
(Option 6) 27U
26U
1155.70mm
Unit boundary (16 EIA units) 1111.25mm
25U
Unit boundary 1066.80mm
24U
Unit boundary 1022.35mm
23U
Unit boundary 977.90mm
22U
Unit boundary
21U
933.45mm
Unit boundary 889.00mm
20U
Unit boundary 844.55mm
19U
Unit boundary
18U
800.10mm
Unit boundary 755.65mm
17U
Unit boundary 711.20mm
16U
Unit boundary 666.75mm
15U
Unit boundary 622.30mm
14U
Unit boundary
13U
577.85mm
Unit boundary
Area of
12U 533.40mm
DKU (16 EIA units)
Unit boundary
11U
488.95mm
Unit boundary (Option 5) 444.50mm
10U
Unit boundary
9U 400.05mm
Unit boundary 355.60mm
8U
Unit boundary 311.15mm
7U
Unit boundary
6U
266.70mm
Unit boundary 5U
222.25mm
Unit boundary 177.80mm
4U
Unit boundary 3U
133.35mm
Unit boundary 2U 88.90mm
Unit boundary 44.45mm
1U
Unit boundary
(Starting point of
height direction)

RACK-02/12

Fig. 3.5.3-4 Whole Layout of Installation Position Addresses (RACK-02/12)

INST03-05-100
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-110

2. Installing rails
a. Remove the Positioning Pin  from the front of the rail.
b. Remove the screw and nut from the side of the rail.
c. If the insertion hole on the rack is square, replace the Positioning Pin  with the included
Positioning Pin (φ9.2 screw head).
If the insertion hole on the rack is round, go to Procedure d. (Leave the Positioning Pin 
of φ6.8 screw head as it is.)
d. Remove the Positioning Pin  from the rear of the rail.
e. If the insertion hole on the rack is square, replace the Positioning Pin  with the included
Positioning Pin (φ9.2 screw head).
If the insertion hole on the rack is round, go to Procedure f. (Leave the Positioning Pin 
of φ6.8 screw head as it is.)
f. Secure the included spring to the parts for securing the spring on the rear of the rail. (Any
direction is possible.)
g. Do the same procedure for the other rails.

Screw

Slide Rail Positioning Pin 

(Item No. 201)

Nut

Positioning Pin  Front

Slide Rail
(Item No. 201)

Positioning Pin 

Part for Securing the

Spring

Positioning Pin  Rear

Fig. 3.5.3-5 Procedure Prior to Rail Installation

INST03-05-110
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-120

h. Bring down two Clips on the front and rear edge of the rail.
i. Fit Positioning Pins of the rail (two pins in total on the front and back edge) into holes on
the right side of the rack at the position where you want to install the DKU.
j. Raise the Clips of the rail to fix the rail to the rack.

Frame
(Rear)
1 Unit
1 Unit

Frame
(Front)

Positioning Pin
1 Unit
Positioning Pin
Clip 1 Unit

Slide Rail
(Item No. 201)

Clip

Fig. 3.5.3-6 Attachment of Rails

INST03-05-120
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-130

k. Tighten the screw and loop cable tie on the rear edge of the rail to fit the rail to the rack.
Do not tighten a screw on the front edge of the rail, as it shall be tightened afterward.
m. Install the rail into the left side of the rack in the same way as procedures h to k.
The same rails are used for right and left side of the rack, therefore the front and rear of the
rail on the left side are opposite to those of the rail on the right side.
n. Install the other rails in the same manner.

Frame (Rear)

Screw (M5)
(Item No. 202)
Slide Rail

Loop Cable Tie Frame (Front)

(Item No. 2)

Fig. 3.5.3-7 Attachment of Screw and Loop Cable Tie

INST03-05-130
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-140

3. Attach the labels

a. Attach the labels, showing corresponding locations to top side and rear side of the HDU.
Refer to Fig. 3.5.3-8 or Fig. 3.5.3-9.
b. Attach the labels to the other HDU in the same manner.

For HDS
Front

Label (VCCI)
(Item No. 4)

Label-Noise (FCC/CSA)
(Item No. 7)
Label (KOREA-KC)
(Item No. 8)

CE Address Label
(Item No. 11)

Label (BSMI NAME) Label (BSMI-D3300)

(Item No. 9) (Item No. 5)

Rear

Top View of HDU

Fig. 3.5.3-8 Attachment of Labels

INST03-05-140
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-150

For HP Front

Label (VCCI)
(Item No. 4)

Label-Noise (FCC/CSA)
(Item No. 7)

CE Address Label
(Item No. 12)

Label (BSMI NAME) Label (BSMI)

(Item No. 9) (Item No. 6)

Rear

Top View of HDU

Fig. 3.5.3-9 Attachment of Labels

INST03-05-150
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-160

c. Attach the label to the right bottom of the rear door. If the label is already attached, this
procedure is not necessary.

Label (UL3)
(Item No. 10)

Front View of
Rear Door

Fig. 3.5.3-10 Attachment of Label

INST03-05-160
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-170

4. Removing parts
If the HDU is installed at height below 1m or installed by using the special lifter, this
procedure is not required because the HDU is installed into the rack frame with its parts
mounted. (Go to procedure 5.)
If other than above, remove the parts first and then install the HDU into the rack frame.

NOTICE: Be sure to wear your wrist strap and attach to ground prior to performing the
following work. This will ensure that the IC and LSI on the PCB are protected from
static electricity.

a. Attach a label or the like for identification of installation location to a removed part so that
it can be installed in the same place in the HDU.
b. Pull the right and left levers and remove the SSW.
c. Remove the other SSW in the same manner.

SSWxyz-1 SSWxyz-2

NOTE: SSWxyz-1
HDU No. (0, 1, 2, ....., 7)
DKU No. (0, 1, 2, ..., 5)
DKC No. (0, 1)
Rear View of HDU

SSW

Lever

Rear View

Lever

Fig. 3.5.3-11 Removal of SSW

INST03-05-170
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-180

d. Bring the handle down and forward () while pushing the latch of the DKUPS inward
().
e. Pull the DKUPS and remove it from the HDU.
f. Remove the other DKUPS in the same manner.

DKUPSxyz-1 DKUPSxyz-2

NOTE: DKUPSxyz-1
HDU No. (0, 1, 2, ....., 7)
DKU No. (0, 1, 2, ..., 5)
DKC No. (0, 1)
Rear View of HDU

DKUPS

Latch

Rear View


Handle

Fig. 3.5.3-12 Removal of DKUPS

INST03-05-180
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-190

5. Installing the DKU

CAUTION
Paying attention to falls:
Work carefully because the mass of the single LFF SBB is about 27 kg and SFF SBB is
about 23 kg.
Beware over turning and dropping:
To prevent HDU from over turning and dropping, the installation work must be done by
two or more personnel.
a. Install the HDU on the front side of the Rack frame referring to mounting procedure using
the special lifter. (See INST03-15-10 through 40.)
b. When the bezels are not installed in the DKU, secure the front of the DKU with the two
screws.
When the bezels are installed in the DKU, go to Procedure c. (The DKU is secured with
the screws and bezel brackets in the procedure described later.)
c. Install the other HDUs in the same manner.

Rail
Rack Frame

HDU (LFF/SFF SBB)

(Item No. 1)
Front View

Rail

Screw (M5)
(Item No. 202)

Fig. 3.5.3-13 Installing HDU

INST03-05-190
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-200

6. Reinstalling removed parts

If parts were removed in procedure 4, reinstall the parts.
If parts were not removed, go to procedure 7.

a. Make the handle of the DKUPS completely fall down and forward. (See Fig. 3.5.3-12.)
b. Insert the DKUPS into the slot and push it to the full.
c. Completely raise the handle and fix the DKUPS.
d. Install the other DKUPS in the same manner.
e. Make the right and left levers of the SSW open. (See Fig. 3.5.3-11.)
f. Insert the SSW until the edge of the lever comes in contact with the HDU.
g. Close the right and left levers to insert the SSW completely.
h. Install the other SSW in the same manner.

7. Installing the Side Bezel

If the bezels are not installed in the DKU, install the Side Bezel on the front of the HDU.
If the bezels are installed in the DKU, go to Procedure 8.

a. Install the Side Bezel, putting the upper side of the Side Bezel on the hook on the front left
of the HDU and pushing the bottom side.
b. Install the Side Bezel in the other HDUs in the same manner.

Hook

Side Bezel
(Item No.21)

Front View of
HDU

Fig. 3.5.3-14 Attachment of Side Bezel

INST03-05-200
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-210

8. Attaching the Labels

a. If the bezels are not installed in the DKU, attach the eight Label Locations and the two
Labels (DKU-BOX) of the corresponding locations to the Side Bezels on the front side of
the rack.
If the bezels are installed in the DKU, go to Procedure c. (Attach the labels to the side
covers of the bezels in the procedure described later.)
b. If the drive chassis is UBX, attach the two Tags (HDD LABEL) and the two Location
Labels (HDD) above the Tags (HDD LABEL) to the Side Bezels.
If the drive chassis is SBX, go to Procedure c.
Standard Configuration

DKU (16U) DKU (16U)

[DKUBOX-11] [DKUBOX-01]

DKU (16U) DKU (16U) DKU (16U) DKU (16U)

[DKUBOX-15] [DKUBOX-13] [DKUBOX-03] [DKUBOX-05]
42U
DKU (16U) DKU (16U)
[DKUBOX-10] [DKUBOX-00]

DKU (16U) DKU (16U) DKU (16U) DKU (16U)

[DKUBOX-14] [DKUBOX-12] DKC (10U) DKC (10U) [DKUBOX-02] [DKUBOX-04]
[DKC-1] [DKC-0]

RACK-12 RACK-11 RACK-10 RACK-00 RACK-01 RACK-02

Front View

Label Location Side Bezel

(Item No. 20)
Tag (HDD LABEL)
Label Location
(Item No. 23) (Only UBX)
(Item No. 19)
Location Label (HDD)
Label Location
(Item No. 22) (Only UBX)
(Item No. 18)
Label (DKU-BOX)
Label Location
(Item No. 3)
(Item No. 17)

Label Location
(Item No. 16)
Tag (HDD LABEL)
Label Location
(Item No. 23) (Only UBX)
(Item No. 15)
Location Label (HDD)
Label Location
(Item No. 22) (Only UBX)
(Item No. 14)
Label (DKU-BOX)
Label Location (Item No. 3)
(Item No. 13)

Front View of RACK

Fig. 3.5.3-15 Attachment of Labels (Front)
INST03-05-210
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-220

c. Attach the ten labels to the rear side of the rail.

Label Location
(Item No. 20)
Label (DKU-BOX)
(Item No. 3)
Label Location
(Item No. 19)

Label Location
(Item No. 18)

Label Location
(Item No. 17)

Label Location
(Item No. 16)

Label Location
(Item No. 15)

Label Location
(Item No. 14)

Label Location
(Item No. 13)

Rail

Rear View of RACK

Fig. 3.5.3-16 Attachment of Labels (Rear)

INST03-05-220
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-230

9. Switch Setting
a. Open the cover of all the SSWs.

Front View of SSW

Cover Switch

Rear View of UBX/SBX

Fig. 3.5.3-17 Opening Cover

INST03-05-230
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-240

CAUTION
A serious failure occurs if a wrong setting is made.
Operate very carefully referring to the setting table not to make a mistake in the setting.
b. Set the switches in the SSWs as indicated in the Fig. 3.5.3-18 through Fig. 3.5.3-30.
Switch settings must be made at 112 places in total per option.
c. Close the cover of all the SSWs. (Refer to Fig. 3.5.3-17.)

NOTICE: • Use something sharp (ex. a pen or a mini screwdriver etc) when set the
SSW switches.
• When the switch setting of SSW is wrong, execute the replace process of
SSW and change the switch setting. The switch setting will not be effective
unless the SSW PCB is dismounted and mounted.

SSWxy7-1 SSWxy7-2

SSWxy6-1 SSWxy6-2

SSWxy5-1 SSWxy5-2
SSWxyz-# (*1)
Switch (SW1-8)
SSWxy4-1 SSWxy4-2

SSWxy3-1 SSWxy3-2
Front View of SSW

SSWxy2-1 SSWxy2-2

SSWxy1-1 SSWxy1-2 ON (*2)

OFF (*2)
SSWxy0-1 SSWxy0-2
8 7 6 5 4 3 2 1

Rear View of UBX/SBX

*1: SSWxyz-# *2:

ON OFF

SSW Location (#: 1, 2)

HDU No. (z: 0, 1, 2,..., 7)
DKU No. (y: 0, 1, 2,..., 5)
DKC No. (x: 0, 1)
Fig. 3.5.3-18 Switch Setting of SSW

INST03-05-240
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-250

OFF
OFF
OFF
OFF
N/A

ON
ON
ON
SSW007-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF
OFF
OFF
N/A

ON
ON
DKU-00 SSW006-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF
OFF
OFF
N/A

ON

ON
SSW005-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF
OFF
OFF
OFF
N/A

ON
SSW004-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF
OFF
OFF
N/A

ON
ON
SSW003-1/2

8 7 6 5 4 3 2 1
OFF

OFF
OFF
OFF
OFF
OFF
N/A

ON

Rear View of UBX/SBX

SSW002-1/2

8 7 6 5 4 3 2 1
OFF
OFF
OFF
OFF
OFF
OFF
N/A

ON

SSW001-1/2

8 7 6 5 4 3 2 1
OFF
OFF
OFF
OFF
OFF
OFF
OFF
N/A

SSW000-1/2

8 7 6 5 4 3 2 1
Fig. 3.5.3-19 Switch Setting of SSW (DKU-00)
INST03-05-250
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-260

OFF
OFF
OFF
N/A

ON
ON
ON
ON
SSW017-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF
OFF
N/A

ON
ON
ON
DKU-01 SSW016-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF
OFF
N/A

ON

ON
ON
SSW015-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF
OFF
OFF
N/A

ON
ON
SSW014-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF
OFF
N/A

ON
ON
ON
SSW013-1/2

8 7 6 5 4 3 2 1
OFF

OFF
OFF
OFF
OFF
N/A

ON
ON

Rear View of UBX/SBX SSW012-1/2

8 7 6 5 4 3 2 1
OFF
OFF
OFF
OFF
OFF
N/A

ON
ON

SSW011-1/2

8 7 6 5 4 3 2 1
OFF
OFF
OFF
OFF
OFF
OFF
N/A

ON

SSW010-1/2

8 7 6 5 4 3 2 1
Fig. 3.5.3-20 Switch Setting of SSW (DKU-01)
INST03-05-260
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-270

OFF
OFF

OFF
N/A

ON
ON
ON
ON
SSW027-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF

OFF
N/A

ON
ON
ON
DKU-02 SSW026-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF

OFF
N/A

ON

ON
ON
SSW025-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF
OFF

OFF
N/A

ON
ON
SSW024-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF

OFF
N/A

ON
ON
ON
SSW023-1/2

8 7 6 5 4 3 2 1
OFF

OFF
OFF
OFF

OFF
N/A

ON
ON

Rear View of UBX/SBX

SSW022-1/2

8 7 6 5 4 3 2 1
OFF
OFF
OFF
OFF

OFF
N/A

ON
ON

SSW021-1/2

8 7 6 5 4 3 2 1
OFF
OFF
OFF
OFF
OFF

OFF
N/A

ON

SSW020-1/2

8 7 6 5 4 3 2 1
Fig. 3.5.3-21 Switch Setting of SSW (DKU-02)
INST03-05-270
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-280

OFF
OFF
N/A

ON
ON
ON
ON
ON
SSW037-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF
N/A

ON
ON
ON
ON
DKU-03 SSW036-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF
N/A

ON

ON
ON
ON
SSW035-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF
OFF
N/A

ON
ON
ON
SSW034-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF
N/A

ON
ON
ON
ON
SSW033-1/2

8 7 6 5 4 3 2 1
OFF

OFF
OFF
OFF
N/A

ON
ON
ON

Rear View of UBX/SBX SSW032-1/2

8 7 6 5 4 3 2 1
OFF
OFF
OFF
OFF
N/A

ON
ON
ON

SSW031-1/2

8 7 6 5 4 3 2 1
OFF
OFF
OFF
OFF
OFF
N/A

ON
ON

SSW030-1/2

8 7 6 5 4 3 2 1
Fig. 3.5.3-22 Switch Setting of SSW (DKU-03)
INST03-05-280
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-290

OFF

OFF
OFF
N/A

ON
ON
ON
ON
SSW047-1/2

8 7 6 5 4 3 2 1

OFF
OFF

OFF
OFF
N/A

ON
ON
ON
DKU-04 SSW046-1/2

8 7 6 5 4 3 2 1

OFF
OFF

OFF
OFF
N/A

ON

ON
ON
SSW045-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF

OFF
OFF
N/A

ON
ON
SSW044-1/2

8 7 6 5 4 3 2 1

OFF
OFF

OFF
OFF
N/A

ON
ON
ON
SSW043-1/2

8 7 6 5 4 3 2 1
OFF

OFF
OFF

OFF
OFF
N/A

ON
ON

Rear View of UBX/SBX SSW042-1/2

8 7 6 5 4 3 2 1
OFF
OFF
OFF

OFF
OFF
N/A

ON
ON

SSW041-1/2

8 7 6 5 4 3 2 1
OFF
OFF
OFF
OFF

OFF
OFF
N/A

ON

SSW040-1/2

8 7 6 5 4 3 2 1
Fig. 3.5.3-23 Switch Setting of SSW (DKU-04)
INST03-05-290
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-300

OFF

OFF
N/A

ON
ON
ON
ON

ON
SSW057-1/2

8 7 6 5 4 3 2 1

OFF
OFF

OFF
N/A

ON
ON
ON

ON
DKU-05 SSW056-1/2

8 7 6 5 4 3 2 1

OFF
OFF

OFF
N/A

ON

ON
ON

ON
SSW055-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF

OFF
N/A

ON
ON

ON
SSW054-1/2

8 7 6 5 4 3 2 1

OFF
OFF

OFF
N/A

ON
ON
ON

ON
SSW053-1/2

8 7 6 5 4 3 2 1
OFF

OFF
OFF

OFF
N/A

ON
ON

ON

Rear View of UBX/SBX SSW052-1/2

8 7 6 5 4 3 2 1
OFF
OFF
OFF

OFF
N/A

ON
ON

ON

SSW051-1/2

8 7 6 5 4 3 2 1
OFF
OFF
OFF
OFF

OFF
N/A

ON

ON

SSW050-1/2

8 7 6 5 4 3 2 1
Fig. 3.5.3-24 Switch Setting of SSW (DKU-05)
INST03-05-300
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-310

OFF
OFF
OFF
N/A

ON
ON
ON
ON
SSW107-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF
OFF
N/A

ON
ON
ON
DKU-10 SSW106-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF
OFF
N/A

ON

ON
ON
SSW105-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF
OFF
OFF
N/A

ON
ON
SSW104-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF
OFF
N/A

ON
ON
ON
SSW103-1/2

8 7 6 5 4 3 2 1
OFF

OFF
OFF
OFF
OFF
N/A

ON
ON

Rear View of UBX/SBX

SSW102-1/2

8 7 6 5 4 3 2 1
OFF
OFF
OFF
OFF
OFF
N/A

ON
ON

SSW101-1/2

8 7 6 5 4 3 2 1
OFF
OFF
OFF
OFF
OFF
OFF
N/A
ON

SSW100-1/2

8 7 6 5 4 3 2 1
Fig. 3.5.3-25 Switch Setting of SSW (DKU-10)
INST03-05-310
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-320

OFF
OFF
N/A

ON
ON
ON
ON

ON
SSW117-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF
N/A

ON
ON
ON

ON
DKU-11 SSW116-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF
N/A

ON

ON
ON

ON
SSW115-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF
OFF
N/A

ON
ON

ON
SSW114-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF
N/A

ON
ON
ON

ON
SSW113-1/2

8 7 6 5 4 3 2 1
OFF

OFF
OFF
OFF
N/A

ON
ON

ON

Rear View of UBX/SBX SSW112-1/2

8 7 6 5 4 3 2 1
OFF
OFF
OFF
OFF
N/A

ON
ON

ON

SSW111-1/2

8 7 6 5 4 3 2 1
OFF
OFF
OFF
OFF
OFF
N/A
ON

ON

SSW110-1/2

8 7 6 5 4 3 2 1
Fig. 3.5.3-26 Switch Setting of SSW (DKU-11)
INST03-05-320
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-330

OFF

OFF
N/A

ON
ON
ON
ON

ON
SSW127-1/2

8 7 6 5 4 3 2 1

OFF
OFF

OFF
N/A

ON
ON
ON

ON
DKU-12 SSW126-1/2

8 7 6 5 4 3 2 1

OFF
OFF

OFF
N/A

ON

ON
ON

ON
SSW125-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF

OFF
N/A

ON
ON

ON
SSW124-1/2

8 7 6 5 4 3 2 1

OFF
OFF

OFF
N/A

ON
ON
ON

ON
SSW123-1/2

8 7 6 5 4 3 2 1
OFF

OFF
OFF

OFF
N/A

ON
ON

ON

Rear View of UBX/SBX

SSW122-1/2

8 7 6 5 4 3 2 1
OFF
OFF
OFF

OFF
N/A

ON
ON

ON

SSW121-1/2

8 7 6 5 4 3 2 1
OFF
OFF
OFF
OFF

OFF
N/A
ON

ON

SSW120-1/2

8 7 6 5 4 3 2 1
Fig. 3.5.3-27 Switch Setting of SSW (DKU-12)
INST03-05-330
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-340

OFF
N/A

ON
ON
ON
ON

ON
ON
SSW137-1/2

8 7 6 5 4 3 2 1

OFF
OFF
N/A

ON
ON
ON

ON
ON
DKU-13 SSW136-1/2

8 7 6 5 4 3 2 1

OFF
OFF
N/A

ON

ON
ON

ON
ON
SSW135-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF
N/A

ON
ON

ON
ON
SSW134-1/2

8 7 6 5 4 3 2 1

OFF
OFF
N/A

ON
ON
ON

ON
ON
SSW133-1/2

8 7 6 5 4 3 2 1
OFF

OFF
OFF
N/A

ON
ON

ON
ON

Rear View of UBX/SBX

SSW132-1/2

8 7 6 5 4 3 2 1
OFF
OFF
OFF
N/A

ON
ON

ON
ON

SSW131-1/2

8 7 6 5 4 3 2 1
OFF
OFF
OFF
OFF
N/A
ON

ON
ON

SSW130-1/2

8 7 6 5 4 3 2 1
Fig. 3.5.3-28 Switch Setting of SSW (DKU-13)
INST03-05-340
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-350

OFF
OFF
N/A

ON
ON
ON
ON
ON
SSW147-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF
N/A

ON
ON
ON
ON
DKU-14 SSW146-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF
N/A

ON

ON
ON
ON
SSW145-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF
OFF
N/A

ON
ON
ON
SSW144-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF
N/A

ON
ON
ON
ON
SSW143-1/2

8 7 6 5 4 3 2 1
OFF

OFF
OFF
OFF
N/A

ON
ON
ON

Rear View of UBX/SBX

SSW142-1/2

8 7 6 5 4 3 2 1
OFF
OFF
OFF
OFF
N/A

ON
ON
ON

SSW141-1/2

8 7 6 5 4 3 2 1
OFF
OFF
OFF
OFF
OFF
N/A
ON
ON

SSW140-1/2

8 7 6 5 4 3 2 1
Fig. 3.5.3-29 Switch Setting of SSW (DKU-14)
INST03-05-350
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-360

OFF
N/A

ON
ON
ON
ON
ON

ON
SSW157-1/2

8 7 6 5 4 3 2 1

OFF
OFF
N/A

ON
ON
ON
ON

ON
DKU-15 SSW156-1/2

8 7 6 5 4 3 2 1

OFF
OFF
N/A

ON

ON
ON
ON

ON
SSW155-1/2

8 7 6 5 4 3 2 1

OFF
OFF
OFF
N/A

ON
ON
ON

ON
SSW154-1/2

8 7 6 5 4 3 2 1

OFF
OFF
N/A

ON
ON
ON
ON

ON
SSW153-1/2

8 7 6 5 4 3 2 1
OFF

OFF
OFF
N/A

ON
ON
ON

ON

Rear View of UBX/SBX

SSW152-1/2

8 7 6 5 4 3 2 1
OFF
OFF
OFF
N/A

ON
ON
ON

ON

SSW151-1/2

8 7 6 5 4 3 2 1
OFF
OFF
OFF
OFF
N/A
ON
ON

ON

SSW150-1/2

8 7 6 5 4 3 2 1
Fig. 3.5.3-30 Switch Setting of SSW (DKU-15)
INST03-05-360
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-370

10. Attachment of Bezel (8U)

a. Position drive chassis so that the protrusions on drive chassis align vertically.

Protrusion

Align the position.

Front View of
RACK

Fig. 3.5.3-31 Positioning Drive Chassis

INST03-05-370
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-380

b. Secure the Nut Plate L (two) to the front left side of the DKU with the four screws.
Tighten the screws pressing the Nut Plate L (two) upward and inward.
c. Secure the Nut Plate R (two) to the front right side of the DKU with the four screws.
Tighten the screws pressing the Nut Plate R (two) upward and inward.

Nut Plate L
(Item No. 106) A

Nut Plate R
(Item No. 107)

Screw (M5)
(Item No. 202) B

Screw (M5)
(Item No. 202)

Front View of Nut Plate R

RACK (Item No. 107)

Press Press

Press Press

Press Press

Press Press

Press Press

Press Press

Detailed View of A Detailed View of B

Fig. 3.5.3-32 Attachment of Nut Plates

INST03-05-380
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-390

d. Hang the upper part of the Bezel Bracket L on the DKU and secure it to the Nut Plate L
(two) with the four screws. Tighten the screws pressing the Bezel Bracket L inward.
e. Hang the upper part of the Bezel Bracket R on the DKU and secure it to the Nut Plate R
(two) with the four screws. Tighten the screws pressing the Bezel Bracket R inward.

Bezel Bracket L A
(Item No. 105)

Screw (SB305N)
(Item No.108)

Screw (SB305N)
(Item No. 108)

Front View of
RACK Bezel Bracket R
(Item No. 102)

Press Press

Press Press

Press Press

Press
Press

Detailed View of A Detailed View of B

Fig. 3.5.3-33 Attachment of Bezel Brackets

INST03-05-390
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-400

f. Fix the Bezel Bracket L so that the protrusions on drive chassis fit into the grooves on the
Bezel Bracket L.
g. Install the Side Cover R in the Bezel Bracket R.
h. Install the parts to the other four HDU in the same manner.

Protrusion

C
Groove

Detailed View of C

Side Cover L
(Item No. 103)

Front View of
RACK
Side Cover R
(Item No. 104)

No Gap

Front View of
RACK

Fig. 3.5.3-34 Attachment of Side Covers

INST03-05-400
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-410

i. Attach the eight Label Locations and the two Labels (DKU-BOX) of the corresponding
locations to the two side covers on the front side of the rack.
j If the drive chassis is UBX, attach the two Location Labels (HDD) to the two Side Cover
L.
If the drive chassis is SBX, go to Procedure k.

Standard Configuration

DKU (16U) DKU (16U)

[DKUBOX-11] [DKUBOX-01]

DKU (16U) DKU (16U) DKU (16U) DKU (16U)

[DKUBOX-15] [DKUBOX-13] [DKUBOX-03] [DKUBOX-05]
42U
DKU (16U) DKU (16U)
[DKUBOX-10] [DKUBOX-00]

DKU (16U) DKU (16U) DKU (16U) DKU (16U)

[DKUBOX-14] [DKUBOX-12] DKC (10U) DKC (10U) [DKUBOX-02] [DKUBOX-04]
[DKC-1] [DKC-0]

RACK-12 RACK-11 RACK-10 RACK-00 RACK-01 RACK-02

Front View

Label Location Side Cover L

(Item No. 20)

Label Location
(Item No. 19)

Label Location Location Label (HDD)

(Item No. 18) (Item No. 22) (Only UBX)

Label (DKU-BOX)
Label Location (Item No. 3)
(Item No. 17)

Label Location Side Cover L

(Item No. 16)

Label Location
(Item No. 15)

Label Location Location Label (HDD)

(Item No. 14) (Item No. 22) (Only UBX)

Label (DKU-BOX)
Label Location (Item No. 3)
(Item No. 13)

Front View of RACK

Fig. 3.5.3-35 Attachment of Labels (Front)

INST03-05-410
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-420

k. Unlock the bezel with the key, and hold the key and bottom of bezel with your both hands.
m. Insert the tabs on the left front side of the chassis into the tab holes on the bezel ().
n. Fix the bezel by pressing the right side of the bezel to engage it with the ball catch on the
front side of the chassis ().
p. Lock the bezel with the key ().
q. Install the bezel to the other four HDU in the same manner.

Tab

Tab Hole

 Ball Catch




Key
The state in which the slit of the (Item No. 109)
keyhole is aligned with the mark.
(The key can be inserted or pulled out
in this state.)
DKU Bezel
Keyhole (Item No. 101)
To lock

Fig. 3.5.3-36 Attachment of DKU Bezel

11. Return to the working table and do the rest of the work.
New Installation: INST02-10
Non-Disruptive Installation: INST02-50

INST03-05-420
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-430

3.5.4 Installation Procedure of FMD Chassis (DKC-F810I-FBX)

1. Confirmation of installation position
EIA units and intervals of mounting holes of 19-inch rack frame conforming to EIA standard
• A unit (U) space conforming to EIA standard is 19 inches wide and 44.5 mm high as shown
in the figure below.
• The boundary of the unit falls on the middle of the interval of 12.7 mm.
• Universal intervals: Repeat of 44.45 mm (15.875 mm + 15.875 mm + 12.7 mm)
Wide intervals: Repeat of 44.45 mm (31.75 mm + 12.7 mm)
Maximum number of mountable unit spaces: 42

12.7mm Unit Boundary

15.875mm 1U = 44.45mm
31.75mm
15.875mm 1 unit (EIA)
12.7mm Unit Boundary

Some types of rack frame do not have this hole.

Rack frame with the holes: Universal interval
Rack frame without the holes: Wide interval
Fig. 3.5.4-1 Attachment Hole Size of Rack

INST03-05-430
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-440

The addresses are given as 1, 2, 3, and so on counted from the bottom of the rack frame.
The following figures show a layout example of installing Drive chassis in 42 units rack frame.
However, installing positions of FMD Chassis may differ according to the construction within
the rack frame.

Addresses of installation The height from the bottom

positions boundary of number 1U

Unit boundary 1866.90mm

42U
Unit boundary 1822.45mm
41U
Unit boundary 1778.00mm
40U
Unit boundary 1733.55mm
39U
Unit boundary 1689.10mm
38U
Unit boundary 1644.65mm
37U
Unit boundary 1600.20mm
Unit boundary 36U
35U 1555.75mm
Unit boundary 1511.30mm
34U
Unit boundary 1466.85mm
33U
Unit boundary 1422.40mm
Unit boundary 32U
31U 1377.95mm
Unit boundary 1333.50mm
Unit boundary 30U
1289.05mm
Unit boundary 29U
1244.60mm
28U
Unit boundary 1200.15mm
27U
Unit boundary 1155.70mm
26U
Unit boundary 1111.25mm
25U
Unit boundary 1066.80mm
Area of 24U
Unit boundary 1022.35mm
FBX 23U (8 EIA units)
Unit boundary 977.90mm
(Option 2) 22U
Unit boundary
21U
933.45mm
Unit boundary
20U
889.00mm
Unit boundary 844.55mm
19U
Unit boundary
18U
800.10mm
Unit boundary 755.65mm
17U
Unit boundary 711.20mm
Area of 16U
Unit boundary 666.75mm
Unit boundary FBX 15U (8 EIA units)
14U 622.30mm
Unit boundary (Option 1) 577.85mm
13U
Unit boundary 533.40mm
12U
Unit boundary
11U
488.95mm
Unit boundary
10U
444.50mm
Unit boundary 400.05mm
9U
Unit boundary 355.60mm
8U
Unit boundary 7U
311.15mm
Unit boundary
6U
266.70mm
Unit boundary 5U
222.25mm
Unit boundary 177.80mm
4U
Unit boundary 3U
133.35mm
Unit boundary 2U 88.90mm
Unit boundary 44.45mm
1U
Unit boundary
(Starting point of
height direction)

RACK-00/10

Fig. 3.5.4-2 Whole Layout of Installation Position Addresses (RACK-00/10)

INST03-05-440
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-450

Addresses of installation The height from the bottom

positions boundary of number 1U

Unit boundary 1866.90mm

42U
Unit boundary 1822.45mm
41U
Unit boundary 1778.00mm
40U
Unit boundary 1733.55mm
39U
Unit boundary 1689.10mm
38U
Unit boundary 1644.65mm
37U
Unit boundary 1600.20mm
36U
Unit boundary 1555.75mm
35U
Unit boundary 1511.30mm
34U
Unit boundary 1466.85mm
33U
Unit boundary 1422.40mm
Unit boundary 32U
31U 1377.95mm
Unit boundary 1333.50mm
Unit boundary 30U
29U
1289.05mm
Unit boundary 1244.60mm
28U
Unit boundary 1200.15mm
27U
Unit boundary 1155.70mm
26U
Unit boundary 1111.25mm
25U
Unit boundary 1066.80mm
24U
Unit boundary 1022.35mm
23U
Unit boundary 977.90mm
22U
Unit boundary
21U
933.45mm
Unit boundary
20U
889.00mm
Unit boundary 844.55mm
19U
Unit boundary 800.10mm
18U
Unit boundary 755.65mm
17U
Unit boundary 711.20mm
Area of 16U
Unit boundary
(8 EIA units) 666.75mm
FBX 15U
Unit boundary 622.30mm
(Option 4) 14U
Unit boundary
13U
577.85mm
Unit boundary 533.40mm
12U
Unit boundary
11U
488.95mm
Unit boundary
10U
444.50mm
Unit boundary
9U 400.05mm
Unit boundary 355.60mm
Area of 8U
Unit boundary 311.15mm
FBX 7U (8 EIA units)
Unit boundary 266.70mm
(Option 3) 6U
222.25mm
Unit boundary
5U
Unit boundary 177.80mm
4U
Unit boundary 3U
133.35mm
Unit boundary 2U 88.90mm
Unit boundary 44.45mm
1U
Unit boundary
(Starting point of
height direction)

RACK-01/11

Fig. 3.5.4-3 Whole Layout of Installation Position Addresses (RACK-01/11)

INST03-05-450
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-460

Addresses of installation The height from the bottom

positions boundary of number 1U

Unit boundary 1866.90mm

42U
Unit boundary 1822.45mm
41U
Unit boundary 1778.00mm
40U
Unit boundary 1733.55mm
39U
Unit boundary 1689.10mm
38U
Unit boundary 1644.65mm
37U
Unit boundary 1600.20mm
Unit boundary 36U
35U 1555.75mm
Unit boundary 1511.30mm
34U
Unit boundary 1466.85mm
33U
Unit boundary 1422.40mm
Unit boundary 32U
31U 1377.95mm
Unit boundary 1333.50mm
Unit boundary 30U
1289.05mm
Unit boundary 29U
1244.60mm
28U
Unit boundary 1200.15mm
27U
Unit boundary 1155.70mm
26U
Unit boundary 1111.25mm
25U
Unit boundary 1066.80mm
24U
Unit boundary 1022.35mm
23U
Unit boundary 977.90mm
22U
Unit boundary
21U
933.45mm
Unit boundary
20U
889.00mm
Unit boundary 844.55mm
19U
Unit boundary
18U
800.10mm
Unit boundary 755.65mm
17U
Unit boundary 711.20mm
Area of 16U
Unit boundary
(8 EIA units) 666.75mm
FBX 15U
Unit boundary 622.30mm
(Option 6) 14U
Unit boundary
13U
577.85mm
Unit boundary 533.40mm
12U
Unit boundary
11U
488.95mm
Unit boundary
10U
444.50mm
Unit boundary 400.05mm
9U
Unit boundary 355.60mm
Area of 8U
Unit boundary 311.15mm
FBX 7U (8 EIA units)
Unit boundary 266.70mm
(Option 5) 6U
222.25mm
Unit boundary 5U
Unit boundary 177.80mm
4U
Unit boundary 3U
133.35mm
Unit boundary 2U 88.90mm
Unit boundary 44.45mm
1U
Unit boundary
(Starting point of
height direction)

RACK-02/12

Fig. 3.5.4-4 Whole Layout of Installation Position Addresses (RACK-02/12)

INST03-05-460
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-470

2. Installing the rails.

a. Raise two Clips on the front and rear edge of the rail.
b. If the insertion hole on the rack is square, put the Square Spacer on the Positioning Pin .
If the insertion hole on the rack is round, go to Procedure c.
c. If the insertion hole on the rack is square, put the Square Spacer on the Positioning Pin .
If the insertion hole on the rack is round, go to Procedure d.
d. If the insertion hole on the rack is square, put the Square Spacer on the Positioning Pin .
If the insertion hole on the rack is round, go to Procedure e.
e. Do the same procedure for the other rails.

Positioning Pin 

Clip

Positioning Pin 

Rail R
(Item No. 402)
Clip Positioning Pin 

In the case of Square Hole

Positioning Pin

Square Spacer
(Item No. 406)

Fig. 3.5.4-5 Procedure Prior to Rail Installation

INST03-05-470
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-480

f. Loosen the four screws on the side of the rail and adjust the length of the rail.
If the length of the rail does not become the same as the width of the rack frame even after
the screws are loosen, remove the four screws and adjust the length again.
g. Fit Positioning Pins of the rail (three pins in total on the front and back edge) into holes on
the right side of the rack at the position where you want to install the DKU.
h. Bring down the Clips of the rail to fix the rail to the rack.
i Tighten the four screws on the rail.
j. Install the rail into the left side of the rack in the same way as procedures f to i.

Frame 1 Unit
(Rear)
1 Unit

Frame
Clip (Front)

Positioning Pin
1 Unit
Positioning Pin
Screw 1 Unit

Rail R
(Item No. 402)
Clip Positioning Pin

Fig. 3.5.4-6 Attachment of Rails

INST03-05-480
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-490

k. Tighten the screws and loop cable ties on the rear edge of the rails to fit the rails to the
rack.
Do not tighten a screw on the front edge of the rail, as it shall be tightened afterward.
m. Install the other rails in the same manner.

Rail
Loop Cable Tie
(Item No. 2)

Screw
(Item No. 404)

Rear View of
Rack

Screw Loop Cable Tie

(Item No. 404) (Item No. 2)

Fig. 3.5.4-7 Attachment of Screws and Loop Cable Ties

INST03-05-490
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-500

3. Removing parts
If the FBX is installed at height below 1m or installed by using the special lifter, this procedure
is not required because the FBX is installed into the rack frame with its parts mounted. (Go to
procedure 4.)
If other than above, remove the parts first and then install the FBX into the rack frame.

NOTICE: Be sure to wear your wrist strap and attach to ground prior to performing the
following work. This will ensure that the IC and LSI on the PCB are protected
from static electricity.

a. Attach a label or the like for identification of installation location to a removed part so that
it can be installed in the same place in the FBX.
b. Press the latches of the SSW inward to unlock the levers.
c. Pull the right and left levers and remove the SSW.
d. Remove the other SSW in the same manner.

SSWxyz-1 SSWxyz-2

NOTE: SSWxyz-1
BOX No. (0, 1, 2, 3)
DKU No. (0, 1, 2, ..., 5)
Rear View of FBX DKC No. (0, 1)

SSW

Lever

Rear View

Latch
Lever
Fig. 3.5.4-8 Removal of SSW

INST03-05-500
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-510

e. Bring the handle down and forward () while pushing the latch of the DKUPS inward
().
f. Pull the DKUPS and remove it from the FBX.
g. Remove the other DKUPS in the same manner.

DKUPSxyz-1 DKUPSxyz-2

NOTE: DKUPSxyz-1
BOX No. (0, 1, 2, 3)
DKU No. (0, 1, 2, ..., 5)
Rear View of FBX DKC No. (0, 1)

DKUPS

 Handle

Latch 

DKUPS

Rear View

Handle

Fig. 3.5.4-9 Removal of DKUPS

INST03-05-510
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-520

4. Installing the FBX

CAUTION
Paying attention to falls:
Work carefully because the mass of the single FMU is about 20 kg.
Beware over turning and dropping:
To prevent FMU from over turning and dropping, the installation work must be done by
two or more personnel.
a. Install the FMU on the front side of the Rack frame referring to mounting procedure using
the special lifter. (See INST03-15-10 through 40.)
At this time, be sure the plate of the rear side of the FMU is in the stopper of the rail.
b. When the bezel is not installed in the FBX, secure the front of the FMU with the two
screws.
When the bezel is installed in the FBX, go to Procedure c. (The FMU is secured with the
screws and bezel brackets in the procedure described later.)
c. Install the other FMUs in a same manner.
Rail

FMU
(Item No. 1)

Front View of
Rack Frame

Screw
(Item No. 404)
Rear View

Screw
(Item No. 404)
Stopper

Stopper

Fig. 3.5.4-10 Installing FBX

INST03-05-520
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-530

d. If the bezel is not installed in the FBX, attach the eight Label Locations and the Label
(DKU-BOX) of the corresponding location to the plate on the left side of the front of the
FBX.
If the bezel is installed in the FBX, go to Procedure e. (Attach the labels to the side covers
of the bezels in the procedure described later.)

Standard Configuration

DKU (8U) DKU (8U)

42U
[DKUBOX-11] [DKUBOX-01]

DKU (8U) DKU (8U) DKU (8U) DKU (8U) DKU (8U) DKU (8U)
[DKUBOX-15] [DKUBOX-13] [DKUBOX-10] [DKUBOX-00] [DKUBOX-03] [DKUBOX-05]

DKU (8U) DKU (8U) DKC (10U) DKC (10U) DKU (8U) DKU (8U)
[DKUBOX-14] [DKUBOX-12] [DKC-1] [DKC-0] [DKUBOX-02] [DKUBOX-04]

RACK-12 RACK-11 RACK-10 RACK-00 RACK-01 RACK-02

Front View

Label Location
(Item No. 10) FBX

Label Location
(Item No. 9)

Label Location
(Item No. 8)

Label Location
(Item No. 7)

Label Location
(Item No. 6)

Label Location Front View of

(Item No. 5) Rack Frame

Label (DKU-BOX)
Label Location (Item No. 11)
(Item No. 4)

Label Location
(Item No. 3)

Fig. 3.5.4-11 Attachment of Labels

INST03-05-530
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-540

e. Attach the eight Label Locations and the Label (DKU-BOX) of the corresponding location
to a rail on the left side of the rear of the FBX.

Label Location Rail

(Item No. 10)
Label Location
(Item No. 9)
FBX

Label Location
(Item No. 8)
Label Location
(Item No. 7)

Label Location
(Item No. 6)
Label Location
(Item No. 5)

Rear View

Label Location
(Item No. 4)
Label Location
(Item No. 3)
Label (DKU-BOX)
(Item No. 11)

Fig. 3.5.4-12 Attachment of Labels

INST03-05-540
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-550

5. Reinstalling removed parts

If parts were removed in procedure 3, reinstall the parts.
If parts were not removed, go to procedure 6.

a. Make the handle of the DKUPS completely fall down and forward. (See Fig. 3.5.4-9.)
b. Insert the DKUPS into the slot and push it to the full.
c. Completely raise the handle and fix the DKUPS.
d. Install the other DKUPS in the same manner.
e. Make the right and left levers of the SSW open. (See Fig. 3.5.4-8.)
f. Insert the SSW until the edge of the lever comes in contact with the chassis.
g. Close the right and left levers to insert the SSW completely.
h. Install the other SSW in the same manner.

INST03-05-550
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-560

6. Attaching the labels

a. Attach the labels, showing corresponding locations to top side and rear side of the FMU.
b. Attach the labels to the other FMU in the same manner.

For HDS For HP

Rear Rear

Label (BSMI NAME) Label (BSMI NAME)

(Item No. 17) (Item No. 17)

CE Address Label CE Address Label

(Item No. 18) (Item No. 19)

Label (VCCI) Label (KOREA-KC) Label (VCCI)

(Item No. 12) (Item No. 16) (Item No. 4)

Label-Noise (FCC/CSA) Label (BSMI-D3300) Label-Noise (FCC/CSA) Label (BSMI)

(Item No. 15) (Item No. 13) (Item No. 15) (Item No. 14)

Front Front

Top View of FMU Top View of FMU

Fig. 3.5.4-13 Attachment of Labels

INST03-05-560
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-570

7. Switch Setting
a. Loosen the screw of the SSW and open the cover.
b. Open the cover of all the SSWs in the same manner.

Rear View of
FBX

Cover
Screw

Front of SSW

Fig. 3.5.4-14 Opening Cover

INST03-05-570
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-580

CAUTION
A serious failure occurs if a wrong setting is made.
Operate very carefully referring to the setting table not to make a mistake in the setting.
c. Set the switches in the SSWs as indicated in the Fig. 3.5.4-15 through Fig. 3.5.4-27.
Switch settings must be made at 56 places in total per option.

NOTICE: • Use something sharp (ex. a pen or a mini screwdriver etc.) when set the
SSW switches
• When the switch setting of SSW is wrong, execute the replace process of
SSW and change the switch setting. The switch setting will not be effective
unless the SSW is dismounted and mounted.

d. Close the cover of the SSW and tighten the screw. (Refer to Fig. 3.5.4-14.)
e. Close and fasten the cover of all the SSWs in the same manner.

SSWxy3-1 SSWxy3-2
SSWxyz-# (*1)
SSWxy2-1 SSWxy2-2

SSWxy1-1 SSWxy1-2

SSWxy0-1 SSWxy0-2 Screw Cover

Front View of SSW
Rear View of
FBX

ON (*2)
*1: SSWxyz-#
SSW Location (#: 1, 2) OFF (*2)
BOX No. (z: 0, 1, 2, 3)
DKU No. (y: 0, 1, 2, ..., 5) 8 7 6 5 4 3 2 1
DKC No. (x: 0, 1)

*2: OFF
ON

Fig. 3.5.4-15 Switch Setting of SSW

INST03-05-580
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-590

OFF
OFF
OFF
OFF
OFF
N/A

ON
ON
SSW003-1/2
DKU-00

8 7 6 5 4 3 2 1

OFF
OFF
OFF
OFF
OFF
OFF
N/A

ON
SSW002-1/2

8 7 6 5 4 3 2 1

OFF

OFF
OFF
OFF
OFF
OFF
N/A

ON
Rear View of SSW001-1/2
FBX

8 7 6 5 4 3 2 1

OFF
OFF
OFF
OFF
OFF
OFF
OFF
N/A
SSW000-1/2

8 7 6 5 4 3 2 1
Fig. 3.5.4-16 Switch Setting of SSW (DKU-00)

OFF
OFF
OFF
OFF
N/A

ON
ON
ON
SSW013-1/2
DKU-01

8 7 6 5 4 3 2 1

OFF
OFF
OFF
OFF
OFF
N/A

ON
ON

SSW012-1/2

8 7 6 5 4 3 2 1
OFF

OFF
OFF
OFF
OFF
N/A

ON
ON

Rear View of
SSW011-1/2
FBX

8 7 6 5 4 3 2 1
OFF
OFF
OFF
OFF
OFF
OFF
N/A

ON

SSW010-1/2

8 7 6 5 4 3 2 1
Fig. 3.5.4-17 Switch Setting of SSW (DKU-01)

INST03-05-590
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-600

OFF
OFF
OFF

OFF
N/A

ON
ON
ON
SSW023-1/2
DKU-02

8 7 6 5 4 3 2 1

OFF
OFF
OFF
OFF

OFF
N/A

ON
ON
SSW022-1/2

8 7 6 5 4 3 2 1

OFF

OFF
OFF
OFF

OFF
N/A

ON
ON
Rear View of
SSW021-1/2
FBX

8 7 6 5 4 3 2 1

OFF
OFF
OFF
OFF
OFF

OFF
N/A

ON
SSW020-1/2

8 7 6 5 4 3 2 1
Fig. 3.5.4-18 Switch Setting of SSW (DKU-02)

OFF
OFF
OFF
N/A

ON
ON
ON
ON
SSW033-1/2
DKU-03

8 7 6 5 4 3 2 1

OFF
OFF
OFF
OFF
N/A

ON
ON
ON

SSW032-1/2

8 7 6 5 4 3 2 1
OFF

OFF
OFF
OFF
N/A

ON
ON
ON

Rear View of SSW031-1/2

FBX

8 7 6 5 4 3 2 1
OFF
OFF
OFF
OFF
OFF
N/A

ON
ON

SSW030-1/2

8 7 6 5 4 3 2 1
Fig. 3.5.4-19 Switch Setting of SSW (DKU-03)

INST03-05-600
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-610

OFF
OFF

OFF
OFF
N/A

ON
ON
ON
SSW043-1/2
DKU-04

8 7 6 5 4 3 2 1

OFF
OFF
OFF

OFF
OFF
N/A

ON
ON
SSW042-1/2

8 7 6 5 4 3 2 1

OFF

OFF
OFF

OFF
OFF
N/A

ON
ON
Rear View of
SSW041-1/2
FBX

8 7 6 5 4 3 2 1

OFF
OFF
OFF
OFF

OFF
OFF
N/A

ON
SSW040-1/2

8 7 6 5 4 3 2 1
Fig. 3.5.4-20 Switch Setting of SSW (DKU-04)

OFF
OFF

OFF
N/A

ON
ON
ON

ON
SSW053-1/2
DKU-05

8 7 6 5 4 3 2 1

OFF
OFF
OFF

OFF
N/A

ON
ON

ON

SSW052-1/2

8 7 6 5 4 3 2 1
OFF

OFF
OFF

OFF
N/A

ON
ON

ON

Rear View of SSW051-1/2

FBX

8 7 6 5 4 3 2 1
OFF
OFF
OFF
OFF

OFF
N/A

ON

ON

SSW050-1/2

8 7 6 5 4 3 2 1
Fig. 3.5.4-21 Switch Setting of SSW (DKU-05)

INST03-05-610
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-620

OFF
OFF
OFF
OFF
N/A

ON
ON
ON
SSW103-1/2
DKU-10

8 7 6 5 4 3 2 1

OFF
OFF
OFF
OFF
OFF
N/A

ON
ON
SSW102-1/2

8 7 6 5 4 3 2 1

OFF

OFF
OFF
OFF
OFF
N/A

ON
ON
Rear View of
SSW101-1/2
FBX

8 7 6 5 4 3 2 1

OFF
OFF
OFF
OFF
OFF
OFF
N/A
ON
SSW100-1/2

8 7 6 5 4 3 2 1
Fig. 3.5.4-22 Switch Setting of SSW (DKU-10)

OFF
OFF
OFF
N/A

ON
ON
ON

ON
SSW113-1/2
DKU-11

8 7 6 5 4 3 2 1

OFF
OFF
OFF
OFF
N/A

ON
ON

ON

SSW112-1/2

8 7 6 5 4 3 2 1
OFF

OFF
OFF
OFF
N/A

ON
ON

ON

Rear View of
SSW111-1/2
FBX

8 7 6 5 4 3 2 1
OFF
OFF
OFF
OFF
OFF
N/A
ON

ON

SSW110-1/2

8 7 6 5 4 3 2 1
Fig. 3.5.4-23 Switch Setting of SSW (DKU-11)

INST03-05-620
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-630

OFF
OFF

OFF
N/A

ON
ON
ON

ON
SSW123-1/2
DKU-12

8 7 6 5 4 3 2 1

OFF
OFF
OFF

OFF
N/A

ON
ON

ON
SSW122-1/2

8 7 6 5 4 3 2 1

OFF

OFF
OFF

OFF
N/A

ON
ON

ON
Rear View of SSW121-1/2
FBX

8 7 6 5 4 3 2 1

OFF
OFF
OFF
OFF

OFF
N/A
ON

ON
SSW120-1/2

8 7 6 5 4 3 2 1
Fig. 3.5.4-24 Switch Setting of SSW (DKU-12)

OFF
OFF
N/A

ON
ON
ON

ON
ON
SSW133-1/2
DKU-13

8 7 6 5 4 3 2 1

OFF
OFF
OFF
N/A

ON
ON

ON
ON

SSW132-1/2

8 7 6 5 4 3 2 1
OFF

OFF
OFF
N/A

ON
ON

ON
ON

Rear View of SSW131-1/2

FBX

8 7 6 5 4 3 2 1
OFF
OFF
OFF
OFF
N/A
ON

ON
ON

SSW130-1/2

8 7 6 5 4 3 2 1
Fig. 3.5.4-25 Switch Setting of SSW (DKU-13)

INST03-05-630
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-640

OFF
OFF
OFF
N/A

ON
ON
ON
ON
SSW143-1/2
DKU-14

8 7 6 5 4 3 2 1

OFF
OFF
OFF
OFF
N/A

ON
ON
ON
SSW142-1/2

8 7 6 5 4 3 2 1

OFF

OFF
OFF
OFF
N/A

ON
ON
ON
Rear View of SSW141-1/2
FBX

8 7 6 5 4 3 2 1

OFF
OFF
OFF
OFF
OFF
N/A
ON
ON
SSW140-1/2

8 7 6 5 4 3 2 1
Fig. 3.5.4-26 Switch Setting of SSW (DKU-14)

OFF
OFF
N/A

ON
ON
ON
ON

ON
SSW153-1/2
DKU-15

8 7 6 5 4 3 2 1

OFF
OFF
OFF
N/A

ON
ON
ON

ON

SSW152-1/2

8 7 6 5 4 3 2 1
OFF

OFF
OFF
N/A

ON
ON
ON

ON

Rear View of
SSW151-1/2
FBX

8 7 6 5 4 3 2 1
OFF
OFF
OFF
OFF
N/A
ON
ON

ON

SSW150-1/2

8 7 6 5 4 3 2 1
Fig. 3.5.4-27 Switch Setting of SSW (DKU-15)

INST03-05-640
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-650

8. When you need to install FMD Chassis Bezel (DKC-F810I-BFH/BFP), attach the bezel.
When you do not need to install FMD Chassis Bezel (DKC-F810I-BFH/BFP), go to Procedure
9.
a. Position four FMUs so that the left edges of them are aligned.
b. Secure the Nut Plate L (two) to the front left side of the DKU with the four screws.
c. Secure the Nut Plate R (two) to the front right side of the DKU with the four screws.
d. Secure the Bezel Bracket L to the Nut Plate L (two) with the four screws.
e. Secure the Bezel Bracket R to the Nut Plate R (two) with the four screws.
f. Install the Side Cover L in the Bezel Bracket L.
g. Install the Side Cover R in the Bezel Bracket R.

Align the edges of

four FMUs.

Nut Plate L Nut Plate R

(Item No. 306) (Item No. 307)

Screw
(Item No. 404)

Screw (SB305N)
(Item No. 308)

Screw
(Item No. 404)

Screw (SB305N)
(Item No. 308)

Bezel Bracket L
(Item No. 305)

Side Cover L Nut Plate R

(Item No. 303) (Item No. 307)

Bezel Bracket R
(Item No. 302)

Front View of
RACK Side Cover R
(Item No. 304)

Fig. 3.5.4-28 Attachment of Parts

INST03-05-650
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-660

h. Attach the eight Label Locations and the Label (DKU-BOX) of the corresponding location
to the side cover on the front side of the rack.

Standard Configuration

DKU (8U) DKU (8U)

42U
[DKUBOX-11] [DKUBOX-01]

DKU (8U) DKU (8U) DKU (8U) DKU (8U) DKU (8U) DKU (8U)
[DKUBOX-15] [DKUBOX-13] [DKUBOX-10] [DKUBOX-00] [DKUBOX-03] [DKUBOX-05]

DKU (8U) DKU (8U) DKC (10U) DKC (10U) DKU (8U) DKU (8U)
[DKUBOX-14] [DKUBOX-12] [DKC-1] [DKC-0] [DKUBOX-02] [DKUBOX-04]

RACK-12 RACK-11 RACK-10 RACK-00 RACK-01 RACK-02

Front View

Side Cover L

Label Location
(Item No. 10)

Label Location
(Item No. 9)

Label Location
(Item No. 8)

Label Location
(Item No. 7)

Label Location
(Item No. 6)

Label Location
(Item No. 5)
Front View of
RACK
Label Location
(Item No. 4)
Label (DKU-BOX)
Label Location (Item No. 11)
(Item No. 3)

Fig. 3.5.4-29 Attachment of Labels (Front)

INST03-05-660
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-05-670

i. Unlock the bezel with the key, and hold the key and bottom of bezel with your both hands.
j. Insert the tabs on the left front side of the chassis into the tab holes on the bezel ().
k. Fix the bezel by pressing the right side of the bezel to engage it with the ball catch on the
front side of the chassis ().
l. Lock the bezel with the key ().

Tab

Tab Hole

 Ball Catch




Key
The state in which the slit of the (Item No. 309)
keyhole is aligned with the mark.
(The key can be inserted or pulled out
in this state.)
DKU Bezel
Keyhole (Item No. 301)
To lock

To unlock

Fig. 3.5.4-30 Attachment of DKU Bezel

9. Return to the working table and do the rest of the work.

New Installation: INST02-10
Non-Disruptive Installation: INST02-50

INST03-05-670
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-06-10

3.6 Installation of Power Cord Kit (DKC-F810I-PLUC/PHUC/PFUC/PLEC/PHEC/PFEC/

PLCC/PHCC/PFCC)
3.6.1 Installation of DKC Power Cord Kit (DKC-F810I-PLUC/PLEC/PLCC)

Table 3.6.1-1 Parts List

No. Model Number Part Name Part No. Quantity Remarks
1 DKC-F810I-PLUC PS Cable ASSY 3287124-A 1 1,500mm White Label
PS Cable ASSY 3287124-B 1 1,500mm Yellow Label
PS Cable ASSY 3287124-C 1 1,500mm White Label
PS Cable ASSY 3287124-D 1 1,500mm Yellow Label
Clamp Tape 5544251-3 3
Repeat Binder 5409042-3 4
2 DKC-F810I-PLEC PS Cable ASSY 3287126-A 1 1,500mm White Label
PS Cable ASSY 3287126-B 1 1,500mm Yellow Label
PS Cable ASSY 3287126-C 1 1,500mm White Label
PS Cable ASSY 3287126-D 1 1,500mm Yellow Label
Clamp Tape 5544251-3 3
Repeat Binder 5409042-3 4
3 DKC-F810I-PLCC PS Cable ASSY 3287128-A 1 1,500mm White Label
PS Cable ASSY 3287128-B 1 1,500mm Yellow Label
PS Cable ASSY 3287128-C 1 1,500mm White Label
PS Cable ASSY 3287128-D 1 1,500mm Yellow Label
Clamp Tape 5544251-3 3
Repeat Binder 5409042-3 4

INST03-06-10
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-06-20

1. Confirmation of Installation Position

a. Refer to following figure to confirm the connection location of DKC Power Cord Kit on
DKC. However, installing positions of DKC Power Cord Kit may differ according to the
construction within the rack frame.

DKC (10U)
[DKC-x] DKC-F810I-PLUC/PLEC/PLCC

Rear View of
RACK-00/10

Fig. 3.6.1-1 Mounting Position of DKC Power Cord Kit

INST03-06-20
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-06-30

2. Connection of Cables (DKC Side)

For DKC-0
a. Connect the PS cable ASSYs (DKCPS-1PSx0, DKCPS-2PSx0, DKCPS-1PSx1 and
DKCPS-2PSx1) to the DKCPSs and fix them with the cable holders.
b. Push the cable holders toward the DKCPSs.

DKCPS-00 DKCPS-01 DKCPS-02 DKCPS-03

Rear View of DKC-0

DKCPS-00

DKCPS-01

DKCPS-02

DKCPS-03

PS Cable ASSY
(DKCPS-1PSx0)

PS Cable ASSY
(DKCPS-1PSx1)

PS Cable ASSY Cable Holder

(DKCPS-2PSx0)

PS Cable ASSY Cable DKCPS

(DKCPS-2PSx1)

Cable Holder
Side View of DKCPS

Fig. 3.6.1-2 Connection of Cables

INST03-06-30
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-06-40

For DKC-1
a. Wire the PS cable ASSYs (DKCPS-1PSx0, DKCPS-2PSx0, DKCPS-1PSx1 and DKCPS-
2PSx1) for the DKCPSs. However, do not connect the PS cable ASSYs with the
DKCPSs at this stage.

DKCPS-10 DKCPS-11 DKCPS-12 DKCPS-13

Rear View of DKC-1

DKCPS-10

DKCPS-11

DKCPS-12

DKCPS-13

PS Cable ASSY
(DKCPS-1PSx0)

PS Cable ASSY
(DKCPS-1PSx1)

PS Cable ASSY Cable Holder

(DKCPS-2PSx0)

PS Cable ASSY Cable DKCPS

(DKCPS-2PSx1)

Cable Holder
Side View of DKCPS

Fig. 3.6.1-3 Attachment of Cables

INST03-06-40
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-06-50

3. Connection of Cables (PDU Side)

a. Connect the four PS cable ASSYs to the PDUs.

In the case of HP Model S1324 (3 Phase) installed in a normal direction

L3-4 L3-4

L2-4 L2-4

L1-4 L1-4

L3-3 L3-3

L2-3 L2-3
PDU PDU
L1-3 L1-3

L3-2 L3-2

L2-2 L2-2

L1-2 L1-2

L3-1 L3-1

L2-1 DKC L2-1

L1-1 L1-1

Rear View of
RACK

L2-1 L2-1
PDU-LINE2 PDU-LINE2
L1-1 L1-1
PDU-LINE1 PDU-LINE1

Fig. 3.6.1-4 Connection of Cables (with PDU Cables Downside)

INST03-06-50
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-06-60

In the case of HP Model S1324 (3 Phase) installed upside down

L1-1 L1-1

L2-1 L2-1

L3-1 L3-1

L1-2 L1-2

L2-2 L2-2

L3-2 L3-2

L1-3 L1-3

L2-3 L2-3
PDU PDU
L3-3 L3-3

L1-4 L1-4

L2-4 L2-4

L3-4 L3-4
DKC

Rear View of
RACK

L2-4 L2-4
PDU-LINE2 PDU-LINE2
L3-4 L3-4
PDU-LINE1 PDU-LINE1

Fig. 3.6.1-5 Connection of Cables (with PDU Cables Upside)

INST03-06-60
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-06-70

b. Secure the PS cable ASSYs on the rear side of rack with the repeat binders.
See Fig. 3.6.1-6 or Fig. 3.6.1-7.

In the case of HP Model S1324 (3 Phase) installed in a normal direction

PDU PDU

PS Cable ASSY PS Cable ASSY

(DKCPS-1PSx0, 2PSx0) (DKCPS-1PSx1, 2PSx1)
Repeat
Repeat
Binder
Binder

Rear View of Rear View of

RACK RACK

Fig. 3.6.1-6 Fixing of Cables (with PDU Cables Downside)

INST03-06-70
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-06-80

In the case of HP Model S1324 (3 Phase) installed upside down

PDU PDU

PS Cable ASSY PS Cable ASSY

(DKCPS-1PSx0, 2PSx0) (DKCPS-1PSx1, 2PSx1)
Repeat
Repeat
Binder
Binder

Rear View of Rear View of

RACK RACK

Fig. 3.6.1-7 Fixing of Cables (with PDU Cables Upside)

4. Return to the working table and do the rest of the work.

New Installation: INST02-10
Non-Disruptive Installation: INST02-40

INST03-06-80
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-06-90

3.6.2 Installation of DKU Power Cord Kit (DKC-F810I-PHUC/PHEC/PHCC)

Table 3.6.2-1 Parts List

No. Model Number Part Name Part No. Quantity Remarks
1 DKC-F810I-PHUC PS Cable ASSY 3287125-A 1 1,500mm White Label
PS Cable ASSY 3287125-B 1 1,500mm Yellow Label
PS Cable ASSY 3287125-C 1 1,500mm White Label
PS Cable ASSY 3287125-D 1 1,500mm Yellow Label
PS Cable ASSY 3287125-E 1 1,500mm White Label
PS Cable ASSY 3287125-F 1 1,500mm Yellow Label
PS Cable ASSY 3287125-G 1 1,500mm White Label
PS Cable ASSY 3287125-H 1 1,500mm Yellow Label
PS Cable ASSY 3287125-J 1 1,500mm White Label
PS Cable ASSY 3287125-K 1 1,500mm Yellow Label
PS Cable ASSY 3287125-L 1 1,500mm White Label
PS Cable ASSY 3287125-M 1 1,500mm Yellow Label
PS Cable ASSY 3287125-N 1 1,500mm White Label
PS Cable ASSY 3287125-P 1 1,500mm Yellow Label
PS Cable ASSY 3287125-Q 1 1,500mm White Label
PS Cable ASSY 3287125-R 1 1,500mm Yellow Label
Binder 5552817-1 16
Repeat Binder 5409042-3 8
2 DKC-F810I-PHEC PS Cable ASSY 3287127-A 1 1,500mm White Label
PS Cable ASSY 3287127-B 1 1,500mm Yellow Label
PS Cable ASSY 3287127-C 1 1,500mm White Label
PS Cable ASSY 3287127-D 1 1,500mm Yellow Label
PS Cable ASSY 3287127-E 1 1,500mm White Label
PS Cable ASSY 3287127-F 1 1,500mm Yellow Label
PS Cable ASSY 3287127-G 1 1,500mm White Label
PS Cable ASSY 3287127-H 1 1,500mm Yellow Label
PS Cable ASSY 3287127-J 1 1,500mm White Label
PS Cable ASSY 3287127-K 1 1,500mm Yellow Label
PS Cable ASSY 3287127-L 1 1,500mm White Label
PS Cable ASSY 3287127-M 1 1,500mm Yellow Label
(To be continued)

INST03-06-90
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-06-100

(Continued from the preceding page)

No. Model Number Part Name Part No. Quantity Remarks
2 DKC-F810I-PHEC PS Cable ASSY 3287127-N 1 1,500mm White Label
PS Cable ASSY 3287127-P 1 1,500mm Yellow Label
PS Cable ASSY 3287127-Q 1 1,500mm White Label
PS Cable ASSY 3287127-R 1 1,500mm Yellow Label
Binder 5552817-1 16
Repeat Binder 5409042-3 8
3 DKC-F810I-PHCC PS Cable ASSY 3287129-A 1 1,500mm White Label
PS Cable ASSY 3287129-B 1 1,500mm Yellow Label
PS Cable ASSY 3287129-C 1 1,500mm White Label
PS Cable ASSY 3287129-D 1 1,500mm Yellow Label
PS Cable ASSY 3287129-E 1 1,500mm White Label
PS Cable ASSY 3287129-F 1 1,500mm Yellow Label
PS Cable ASSY 3287129-G 1 1,500mm White Label
PS Cable ASSY 3287129-H 1 1,500mm Yellow Label
PS Cable ASSY 3287129-J 1 1,500mm White Label
PS Cable ASSY 3287129-K 1 1,500mm Yellow Label
PS Cable ASSY 3287129-L 1 1,500mm White Label
PS Cable ASSY 3287129-M 1 1,500mm Yellow Label
PS Cable ASSY 3287129-N 1 1,500mm White Label
PS Cable ASSY 3287129-P 1 1,500mm Yellow Label
PS Cable ASSY 3287129-Q 1 1,500mm White Label
PS Cable ASSY 3287129-R 1 1,500mm Yellow Label
Binder 5552817-1 16
Repeat Binder 5409042-3 8

INST03-06-100
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-06-110

1. Confirmation of Installation Position

a. Refer to following figure to confirm the connection location of DKU Power Cord Kit on
DKU. However, installing positions of DKU Power Cord Kit may differ according to the
construction within the rack frame.

DKU (16U)
[DKU-x1]

DKC-F810I-PHUC/PHEC/
PHCC
DKU (16U)
[DKU-x3]
DKC-F810I-PHUC/PHEC/
DKU (16U) PHCC
[DKU-x0]

DKC-F810I-PHUC/PHEC/
PHCC

DKU (16U)
[DKU-x2]

DKC (10U) DKC-F810I-PHUC/PHEC/

[DKC-x] PHCC
2U

Rear View of Rear View of

RACK-00/10 RACK-01/11

DKU (16U)
[DKU-x5]
DKC-F810I-PHUC/PHEC/
PHCC

DKU (16U)
[DKU-x4]
DKC-F810I-PHUC/PHEC/
PHCC
2U

Rear View of
RACK-02/12

Fig. 3.6.2-1 Mounting Location of DKU Power Cord Kit

INST03-06-110
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-06-120

2. Connection of Cables (DKU Side)

a. Put sixteen PS Cable ASSYs through cable holders and connect them to DKUPSs.
b. Close the cable holder, and then push it toward the DKUPS till it stops, holding the end of
the binder.

DKU

DKUPS

DKUPS

DKUPS-xy70 (White Label)

DKUPS-xy60 (White Label)

DKUPS-xy71 (Yellow Label)
DKUPS-xy50 (White Label)

DKUPS-xy61 (Yellow Label)

DKUPS-xy40 (White Label)

DKUPS-xy51 (Yellow Label)

DKUPS-xy30 (White Label)

DKUPS-xy41 (Yellow Label)

DKUPS-xy20 (White Label)
DKUPS-xy31 (Yellow Label)
DKUPS-xy10 (White Label)

DKUPS-xy21( Yellow Label)

DKUPS-xy00 (White Label)

DKUPS-xy11 (Yellow Label)

Latch

Rear View

DKUPS-xy01 (Yellow Label)

Cable Holder

Fig. 3.6.2-2 Connection of Cables

INST03-06-120
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-06-130

c. Attach the binders to the rails of the rear side of the DKUs to fix the cables.

HDU

Rail

PS Cable ASSY

Binder

Rail

Rear View PS Cable ASSY

Fig. 3.6.2-3 Fixation of Cables

INST03-06-130
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-06-140

3. Connection of Cables (PDU Side)

a. Choose a rack configuration from the Fig. 3.6.2-4 Power Cable Connection Diagram and
confirm the location of the power cable connection for the installed DKU.

In the case of HP Model S1324 (3 Phase) installed in a normal direction

HDU 7
HDU 6
L3-4 L3-4 L3-4
HDU 5 L3-4
HDU 4
L2-4 L2-4 L2-4 L2-4
HDU 3
L1-4 L1-4 L1-4 HDU 2 L1-4
HDU 1
L3-3 L3-3 L3-3 HDU 0 L3-3
HDU 7 HDU 7
L2-3 L2-3 L2-3 L2-3
HDU 6 HDU 6
L1-3 HDU 5 L1-3 L1-3 HDU 5 L1-3

HDU 4 HDU 4
L3-2 HDU 3 L3-2 L3-2 HDU 3 L3-2
HDU 2 HDU 2
L2-2 L2-2 L2-2 L2-2
HDU 1 HDU 1
L1-2 HDU 0 L1-2 L1-2 HDU 0 L1-2

L3-1 L3-1 L3-1 L3-1

L2-1 DKC L2-1 L2-1 DKC L2-1

L1-1 L1-1 L1-1 L1-1

Rear View of Rear View of

RACK RACK

In the case of HP Model S1324 (3 Phase) installed upside down

L1-1 L1-1 L1-1 HDU 7 L1-1

HDU 6
L2-1 L2-1 L2-1 HDU 5 L2-1

L3-1 L3-1 L3-1 HDU 4 L3-1

HDU 3
L1-2 L1-2 L1-2 HDU 2 L1-2
HDU 1
L2-2 L2-2 L2-2 L2-2
HDU 0
L3-2 HDU 7 L3-2 L3-2 HDU 7 L3-2
HDU 6 HDU 6
L1-3 HDU 5 L1-3 L1-3 HDU 5 L1-3
HDU 4 HDU 4
L2-3 L2-3 L2-3 L2-3
HDU 3 HDU 3
L3-3 HDU 2 L3-3 L3-3 HDU 2 L3-3
HDU 1 HDU 1
L1-4 HDU 0 L1-4 L1-4 HDU 0 L1-4

L2-4 L2-4 L2-4 L2-4

L3-4 L3-4 L3-4 L3-4

DKC DKC

Rear View of Rear View of

RACK RACK
Fig. 3.6.2-4 Power Cable Connection Diagram

INST03-06-140
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-06-150

b. Connect the 16 PS cable ASSYs to the PDUs that were confirmed in Procedure a.
The following figure shows the example connections of power cables.

In the case of HP Model S1324 (3 Phase) installed in a normal direction

PDU PDU
L3-4 L3-4
L2-4 L2-4
L1-4 L1-4
L3-3 L3-3
L2-3 L2-3
L1-3 L1-3

PDU-LINE8 L3-2 PDU-LINE8 L3-2

PDU-LINE7 L2-2 PDU-LINE7 L2-2
PDU-LINE6 L1-2 PDU-LINE6 L1-2
PDU-LINE5 L3-1 PDU-LINE5 L3-1
PDU-LINE4 L2-1 PDU-LINE4 L2-1
PDU-LINE3 L1-1 PDU-LINE3 L1-1
PDU-LINE2 PDU-LINE2
PDU-LINE1 PDU-LINE1

In the case of HP Model S1324 (3 Phase) installed upside down

PDU PDU

L1-1 L1-1
L2-1 L2-1
L3-1 L3-1
L1-2 L1-2
L2-2 L2-2
L3-2 L3-2

L1-3 L1-3
PDU-LINE8 PDU-LINE8
L2-3 L2-3
PDU-LINE7 PDU-LINE7
L3-3 L3-3
PDU-LINE6 PDU-LINE6
L1-4 L1-4
PDU-LINE5 PDU-LINE5
L2-4 L2-4
PDU-LINE4 PDU-LINE4
L3-4 L3-4
PDU-LINE3 PDU-LINE3
PDU-LINE2 PDU-LINE2
PDU-LINE1 PDU-LINE1

Fig. 3.6.2-5 Example of Connecting Cables

INST03-06-150
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-06-160

c. Secure the PS cable ASSYs on the rear side of rack with the repeat binders.
See Fig. 3.6.2-6, Fig. 3.6.2-7, Fig. 3.6.2-8 or Fig. 3.6.2-9.

In the case of HP Model S1324 (3 Phase) installed in a normal direction

PDU PDU

DKU

Repeat
Binder
Repeat
Binder

Rear View of Rack Rear View of Rack

PS Cable ASSY PS Cable ASSY
(DKUPS-xy00  PDU-LINE1, (DKUPS-xy01  PDU-LINE1,
DKUPS-xy10  PDU-LINE2, DKUPS-xy11  PDU-LINE2,
………, ………,
DKUPS-xy70  PDU-LINE8) DKUPS-xy71  PDU-LINE8)

Fig. 3.6.2-6 Fixation of Cables ((in Middle Part of Rack, with PDU Cables Downside)

INST03-06-160
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-06-170

In the case of HP Model S1324 (3 Phase) installed in a normal direction

DKU

PDU
PDU

Repeat
Binder
Repeat
Binder

Rear View of Rack Rear View of Rack

PS Cable ASSY PS Cable ASSY
(DKUPS-xy00  PDU-LINE1, (DKUPS-xy01  PDU-LINE1,
DKUPS-xy10  PDU-LINE2, DKUPS-xy11  PDU-LINE2,
………, ………,
DKUPS-xy70  PDU-LINE8) DKUPS-xy71  PDU-LINE8)

Fig. 3.6.2-7 Fixation of Cables (in Upper Part of Rack, with PDU Cables Downside)

INST03-06-170
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-06-180

In the case of HP Model S1324 (3 Phase) installed upside down

PDU PDU

DKU

Repeat
Binder
Repeat
Binder

Rear View of Rack Rear View of Rack

PS Cable ASSY PS Cable ASSY
(DKUPS-xy00  PDU-LINE1, (DKUPS-xy01  PDU-LINE1,
DKUPS-xy10  PDU-LINE2, DKUPS-xy11  PDU-LINE2,
………, ………,
DKUPS-xy70  PDU-LINE8) DKUPS-xy71  PDU-LINE8)

Fig. 3.6.2-8 Fixation of Cables (in Middle Part of Rack, with PDU Cables Upside)

INST03-06-180
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-06-190

In the case of HP Model S1324 (3 Phase) installed upside down

DKU

PDU
PDU

Repeat
Binder
Repeat
Binder

Rear View of Rack Rear View of Rack

PS Cable ASSY PS Cable ASSY
(DKUPS-xy00  PDU-LINE1, (DKUPS-xy01  PDU-LINE1,
DKUPS-xy10  PDU-LINE2, DKUPS-xy11  PDU-LINE2,
………, ………,
DKUPS-xy70  PDU-LINE8) DKUPS-xy71  PDU-LINE8)

Fig. 3.6.2-9 Fixation of Cables (in Upper Part of Rack, with PDU Cables Upside)

4. Return to the working table and do the rest of the work.

New Installation: INST02-10
Non-Disruptive Installation: INST02-50

INST03-06-190
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-06-200

3.6.3 Installation of DKU (FBX) Power Cord Kit (DKC-F810I-PFUC/PFEC/PFCC)

Table 3.6.3-1 Parts List

No. Model Number Part Name Part No. Quantity Remarks
1 DKC-F810I-PFUC PS Cable ASSY 3287125-A 1 1,500mm, White Label
DKUPS-xy00 – PDU-LINE1
PS Cable ASSY 3287125-B 1 1,500mm, Yellow Label
DKUPS-xy01 – PDU-LINE1
PS Cable ASSY 3287125-C 1 1,500mm, White Label
DKUPS-xy10 – PDU-LINE2
PS Cable ASSY 3287125-D 1 1,500mm, Yellow Label
DKUPS-xy11 – PDU-LINE2
PS Cable ASSY 3287125-E 1 1,500mm, White Label
DKUPS-xy20 – PDU-LINE3
PS Cable ASSY 3287125-F 1 1,500mm, Yellow Label
DKUPS-xy21 – PDU-LINE3
PS Cable ASSY 3287125-G 1 1,500mm, White Label
DKUPS-xy30 – PDU-LINE4
PS Cable ASSY 3287125-H 1 1,500mm, Yellow Label
DKUPS-xy31 – PDU-LINE4
Repeat Binder 5409042-3 4
2 DKC-F810I-PFEC PS Cable ASSY 3287127-A 1 1,500mm, White Label
DKUPS-xy00 – PDU-LINE1
PS Cable ASSY 3287127-B 1 1,500mm, Yellow Label
DKUPS-xy01 – PDU-LINE1
PS Cable ASSY 3287127-C 1 1,500mm, White Label
DKUPS-xy10 – PDU-LINE2
PS Cable ASSY 3287127-D 1 1,500mm, Yellow Label
DKUPS-xy11 – PDU-LINE2
PS Cable ASSY 3287127-E 1 1,500mm, White Label
DKUPS-xy20 – PDU-LINE3
PS Cable ASSY 3287127-F 1 1,500mm, Yellow Label
DKUPS-xy21 – PDU-LINE3
PS Cable ASSY 3287127-G 1 1,500mm, White Label
DKUPS-xy30 – PDU-LINE4
PS Cable ASSY 3287127-H 1 1,500mm, Yellow Label
DKUPS-xy31 – PDU-LINE4
Repeat Binder 5409042-3 4
(To be continued)

INST03-06-200
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-06-210

(Continued from the preceding page)

No. Model Number Part Name Part No. Quantity Remarks
3 DKC-F810I-PFCC PS Cable ASSY 3287129-A 1 1,500mm, White Label
DKUPS-xy00 – PDU-LINE1
PS Cable ASSY 3287129-B 1 1,500mm, Yellow Label
DKUPS-xy01 – PDU-LINE1
PS Cable ASSY 3287129-C 1 1,500mm, White Label
DKUPS-xy10 – PDU-LINE2
PS Cable ASSY 3287129-D 1 1,500mm, Yellow Label
DKUPS-xy11 – PDU-LINE2
PS Cable ASSY 3287129-E 1 1,500mm, White Label
DKUPS-xy20 – PDU-LINE3
PS Cable ASSY 3287129-F 1 1,500mm, Yellow Label
DKUPS-xy21 – PDU-LINE3
PS Cable ASSY 3287129-G 1 1,500mm, White Label
DKUPS-xy30 – PDU-LINE4
PS Cable ASSY 3287129-H 1 1,500mm, Yellow Label
DKUPS-xy31 – PDU-LINE4
Repeat Binder 5409042-3 4

INST03-06-210
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-06-220

1. Confirmation of Installation Position

a. Refer to following figure to confirm the connection location of DKU Power cord on DKU.
However, installing positions of DKU Power cord may differ according to the construction
within the rack frame.

DKU (8U)
[DKU-02] DKC-F810I-PFUC/PFEC/
PFCC

DKU (8U) DKC-F810I-PFUC/PFEC/

[DKU-01] DKU (8U)
PFCC DKC-F810I-PFUC/PFEC/
[DKU-05]
PFCC

DKU (8U)
[DKU-00] DKC-F810I-PFUC/PFEC/ DKU (8U)
PFCC [DKU-04] DKC-F810I-PFUC/PFEC/
PFCC

DKU (8U)
DKC (10U)
[DKU-03] DKC-F810I-PFUC/PFEC/
[DKC-0]
PFCC
2U

Rear View of Rear View of

RACK-00/10 RACK-01/11

Fig. 3.6.3-1 Mounting Location of DKU Power Cord

INST03-06-220
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-06-230

2. Connection of Cables (DKU Side)

a. Put eight PS Cable ASSYs through cable holders and connect them to DKUPSs.
b. Close the cable holder, and then push it toward the DKUPS till it stops, holding the end of
the binder.

DKUPS

PS Cable ASSY
(DKCPS-xy30) PS Cable ASSY
(DKCPS-xy31)
PS Cable ASSY
(DKCPS-xy20) PS Cable ASSY
(DKCPS-xy21)
PS Cable ASSY
(DKCPS-xy10) PS Cable ASSY
(DKCPS-xy11)
PS Cable ASSY
(DKCPS-xy00) PS Cable ASSY
(DKCPS-xy01)

Rear View of Binder

DKU DKUPS

Cable Holder PS Cable ASSY

Side View of DKUPS

Fig. 3.6.3-2 Connection of PS Cable ASSY

INST03-06-230
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-06-240

3. Connection of Cables (PDU Side)

a. Connect the eight PS cable ASSYs to the PDUs.
NOTE: • Connect the power cables for the DKUPSxyz-1 to the left PDU.
Connect the power cables for the DKUPSxyz-2 to the right PDU.
If they are plugged in the receptacles of the PDUs on the same side, the function of
the duplicated power supply does not work.
• Check the rated current of the PDU to be used and make sure the total load doesn’t
exceed the rated current by calculation when connecting a power cable.

INST03-06-240
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-06-250

b. Secure the PS cable ASSYs on the rear side of rack with the clamp tapes.
The figure below shows an example of fixing cables.

[Example]

PDU PDU

Clamp
Tape
Clamp
Tape
FBX

Rear View of Rack Rear View of Rack

PS Cable ASSY PS Cable ASSY
(DKUPS-xy00  PDU-LINE1, (DKUPS-xy01  PDU-LINE1,
DKUPS-xy10  PDU-LINE2, DKUPS-xy11  PDU-LINE2,
DKUPS-xy20  PDU-LINE3, DKUPS-xy21  PDU-LINE3,
DKUPS-xy30  PDU-LINE4) DKUPS-xy31  PDU-LINE4)

Fig. 3.6.3-3 Example of Fixing Cables

INST03-06-250
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-06-260

4. Return to the working table and do the rest of the work.

New Installation: INST02-10
Non-Disruptive Installation: INST02-50

INST03-06-260
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-10

3.7 Installation of Processor Blade, HUB, Cache Memory, Cache Backup Module kit and
Cache Flash Memory, Inter-Controller Connecting Kit and Inter-Controller Connecting
Cable (DKC-F810I-MP/HUB/CM16G/CM32G/CPEX/BKMS/BKML/BMM128/BMM256/
MOD5/MOD30/MOD1J/MFC5/MFC30/MFC1J)

Notes when installing the DKC-F810I-CBXB:

Please note that an installation for the additional CHA, DKA, HDD and so on at the same time as
CBXB must be executed in steps as follows.
Notes when installing Processor Blade:
Installing a Processor Blade may affect I/O when there is much write pending data in cache. We
recommend to install a Processor Blade when all the cache write pending rate per CLPR in a
Processor Blade is less than 40%.

[Installation Sample]
Step1: Installation of Controller Chassis (DKC-F810I-CBXB) ............................. INST03-04-10
Step2: Installation of Processor Blade, HUB, Cache Memory, Cache Backup Module kit and
Cache Flash Memory, Inter-Controller Connecting Kit and Inter-Controller Connecting
Cable (DKC-F810I-MP/HUB/CM16G/CM32G/CPEX/BKMS/BKML/BMM128/
BMM256/MOD5/MOD30/MOD1J/MFC5/MFC30/MFC1J) ..................... INST03-07-10
Step3: Installation of Channel Adapter (DKC-F810I-8FC16/16FC8/16MS8/16ML8)
.................................................................................................................. INST03-08A-10
Step4: Installation of Drive Chassis (DKC-F810I-UBX/SBX/FBX) ..................... INST03-05-10
Step5: Installation of Disk Adapter, Drive and DEV Interface Cable .................... INST03-11-10

Operate the step 1 to 2 when installing only the additional CBXB.

For the installation of the additional CHA/DKA/HDD at the same time as the CBXB, operate
sequentially the step 3 to 5 after finishing the step 1 to 2.
Installing the additional parts for the step 3 to 5 at the same time as the step 1 to 2 is not possible.
Red LEDs for each part light when the parts mentioned above are installed at the same time.
In this case, remove the part at its related operation step and follow the correct procedures to
reinstall it.

INST03-07-10
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-20

Table 3.7-1 Parts List (Only MPB)

No. Model Number Part Name Part No. Quantity Remarks
1 DKC-F810I-MP WP850-A 5552761-A 2
2 DKC-F810I-HUB HUBBOX 5552760-A 1

Table 3.7-2 Parts List (Module Installation)

No. Model Number Part Name Part No. Quantity Remarks
1 DKC-F810I-MOD5 MODCON 5552749-A 2
H-PCF Cable 5555027-A 2 MODCON Cable
LAN Cable 5555029-A 1
MFC Cable 5552752-A 8
Label (Address) 3 3287145-1 3
Label (Protect) 3287450-1 3
FE Cable Jig 5555008-A 1
Packing Work (PARTS) 3287318-C 1
Screw SB406N 1 (*1)
Cleat 5409055-2 1 (*1)
Clamp Tape 5544251-3 1 (*1)
2 DKC-F810I-MOD30 MODCON 5552749-A 2
H-PCF Cable 5555153-A 2 MODCON Cable
LAN Cable 5555154-A 1
MFC Cable 5555155-A 8
Label (Address) 3 3287145-1 3
Label (Protect) 3287450-1 3
FE Cable Jig 5555008-A 1
Packing Work (PARTS) 3287318-C 1
Screw SB406N 1 (*1)
Cleat 5409055-2 1 (*1)
Clamp Tape 5544251-3 1 (*1)
3 DKC-F810I-MOD1J MODCON 5552749-A 2
H-PCF Cable 5555028-A 2 MODCON Cable
LAN Cable 5555030-A 1
MFC Cable 5552753-A 8
Label (Address) 3 3287145-1 3
Label (Protect) 3287450-1 3
FE Cable Jig 5555008-A 1
Packing Work (PARTS) 3287318-C 1
Screw SB406N 1 (*1)
Cleat 5409055-2 1 (*1)
Clamp Tape 5544251-3 1 (*1)
(To be continued)

INST03-07-20
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-30

(Continued from the preceding page)

No. Model Number Part Name Part No. Quantity Remarks
4 DKC-F810I-MFC5 MFC Cable 5552752-A 8
Label (Address) 3 3287145-1 3
Label (Protect) 3287450-1 3
FE Cable Jig 5555008-A 1
Packing Work (PARTS) 3287318-C 1
Screw SB406N 1 (*1)
Cleat 5409055-2 1 (*1)
Clamp Tape 5544251-3 1 (*1)
5 DKC-F810I-MFC30 MFC Cable 5555155-A 8
Label (Address) 3 3287145-1 3
Label (Protect) 3287450-1 3
FE Cable Jig 5555008-A 1
Packing Work (PARTS) 3287318-C 1
Screw SB406N 1 (*1)
Cleat 5409055-2 1 (*1)
Clamp Tape 5544251-3 1 (*1)
6 DKC-F810I-MFC1J MFC Cable 5552753-A 8
Label (Address) 3 3287145-1 3
Label (Protect) 3287450-1 3
FE Cable Jig 5555008-A 1
Packing Work (PARTS) 3287318-C 1
Screw SB406N 1 (*1)
Cleat 5409055-2 1 (*1)
Clamp Tape 5544251-3 1 (*1)
7 DKC-F810I-CM16G 16GB DIMM 5552764-A 1 CM Module
8 DKC-F810I-CM32G 32GB DIMM 5552765-A 1 CM Module
9 DKC-F810I-CPEX WP840-A 5552763-A 2 CM PCB
HU Jumper 5521578-1 2 Maintenance Jumper
10 DKC-F810I-BKMS BKM 5552766-A 2
11 DKC-F810I-BKML BKM 5552767-A 2
12 DKC-F810I- SSD (128GB) 5552768-A 1 CFM
BMM128 Screw SB305N 2
13 DKC-F810I- SSD (256GB) 5552769-A 1 CFM
BMM256 Screw SB305N 2

*1: These parts are included in Packing Work (PARTS).

INST03-07-30
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-40

Total rough time of installation will be the sum of rough time installation of each item.

Table 3.7-3 Working time

Number of change (set) Total (minutes)
MPB Installation 1 20
2 25
3 30
4 35
5 40
6 45
7 50
Total (minutes)
CACHE Cache memory, CFM equipment Cache memory module: 6min × target CM PCB num.
process CFM: 7.5min × target CM PCB num.
Target CM PCB diagnosis time Target CM PCB diagnosis time 10min × target CM
PCB num.
Target CM PCB recovering time Target CM PCB recovering time 5 ~ 20min × target CM
PCB num. (*1)

*1: Standard processing time is indicated. The processing time depends on the use situation,
especially, the influence of the amount of write pending is received. When the amount of
write pending is large, time more than the indication value might be required.
NOTE: For CACHE installation, additional time for wiring cables is necessary to newly route
cable(s) between modules. (It is not applied to 1 module configuration).

INST03-07-40
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-50

3.7.1 Installation of Module (DKC-F810I-MP/HUB/CM16G/CM32G/CPEX/BKMS/BKML/

BMM128/BMM256/MOD5/MOD30/MOD1J/MFC5/MFC30/MFC1J)
1. Setting up the New Device Structure Information
(1) <Mode Change>
Change the mode to Modify Mode.
Select (CL) [Install].

(2) <Start the ‘Menu Dialog’ screen>

Select (CL) [Change Configuration].

(3) <Start Device Structure Setup screen>

Select (CL) [Installation] in the ‘Menu
Dialog’ dialog box and select (CL) [OK].

(4) <Select a part to be changed>

Select (CL) [MPB + Module], and select
(CL) [OK].

INST03-07-50
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-60

(5) <DKC Configuration screen>

In the ‘DKC Configuration’ screen:
With [Number of Module], select the
number of modules from a pull down
menu.
Select (CL) [Cache].
Go to Step (6).

When installation of the MPB is required:

Select (CL) [CHA/DKA/MPB].
Go to Step (7).

After the setting is completed, select (CL)

[>>Next].
Go to Step (9).
In the case of selecting (CL) [Cancel], this operation procedure terminates.

(6) <Cache Configuration screen>

In the ‘Cache Configuration’ screen,
define each item.

When the change of Cache setting or

installation of the PCB is required, select
(CL) the target Cache PCB and then
select (CL) [Cache Size].
Go to Step (6)-1.

When the change of BKM setting is

required, select (CL) [BKM].
Go to Step (6)-2.

When the change of DCR setting is required, select (CL) [DCR Change].
Go to Step (6)-3.

When the change of CLPR setting is required, select (CL) the target CLPR. and then select
(CL) [Set CLPR].
Go to Step (6)-4.

After setting all items, select (CL) [OK].

Go back to Step (5).

INST03-07-60
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-70

(6)-1 <Cache Size Define screen>

Set the CMG/Cache Size in the ‘Cache Size
Define’ screen, and then select (CL) [OK].
Go back to Step (6).

(6)-2 <BKM screen>

Set the BKM in the ‘BKM Define’ screen, select
(CL) [OK].
Go back to Step (6).

(6)-3 <DCR Available Size Define screen>

Set the DCR available size in the ‘DCR Available
Size Define’ screen, select (CL) [OK].
Go back to Step (6).

(6)-4 <CLPR Define screen>

Set the Cache Size/DCR available
Size/Number of extent in the ‘CLPR Define’
screen, select (CL) [OK].
Go back to Step (6).

INST03-07-70
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-80

(7) <CHA/DKA/MPB Configuration screen>

In the ‘CHA/DKA/MPB Configuration’
screen, select the location(s) to which the
addition is to be made, and select (CL)
[Change...].
Go to Step (8).
Make sure that the entry that has been
made is correct and select (CL) [OK].
Go back to Step (5).

(8) <CHA/DKA/MPB Define screen>

In the ‘CHA/DKA/MPB Define’ screen,
select (CL) [MPB].
After the setting is completed, select (CL)
[OK].
Go back to Step (7).

(9) <LDEV Management MPB Configuration screen>

In the ‘LDEV Management MPB
Configuration’ screen, select installed
MPB and select (CL) [Change].
Go to Step (10).

After the setting is completed, select (CL)

[>>Next].
Go to Step (11).
In the case of selecting (CL) [Cancel],
this operation procedure terminates.

INST03-07-80
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-90

(10) <Auto LDEV Assignment Define screen>

In the ‘Auto LDEV Assignment Define’
screen, select (CL) [Auto LDEV
Assignment].
After the setting is completed, select (CL)
[OK].
Go back to Step (9).

(11) <Battery Life Warning SIM screen>

Select (CL) the target CM Battery in the
‘Battery Life Warning SIM’ screen, and
then select (CL) [Set...].
Go to Step (12).

Make sure that the all input items are

correct and select (CL) [OK].
Go to Step 2.

NOTE: If the date is displayed as

“****/**/**”, follow Step (12)
to set the date.
NOTE: If the check box in [Battery Life Warning SIM] is not checked, ‘Battery Life
Warning SIM’ window is disabled and not displayed. (Go to Step 2.)

(12) <Battery Life Warning SIM screen>

Select (CL) [OK] after inputting the remainder
days until Warning SIM is reported.
Return to Step (11).

NOTE: After executing the periodical

exchange of a battery, set 33 month (990 days).
NOTE: Default value is 33 month (990 days), which is 3 month earlier than the lifetime of
a battery (3 years).
Determine the number of days remained based on your maintenance plan.
NOTE: The input ranges of “Remained Battery life” are from 1 to 3650.

INST03-07-90
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-100

2. SVP pre procedure (HUBBOX Installation)

(1) <Wear a wrist strap>
Select (CL) [OK] in response to “To
prevent serious failures caused by the
static electrical charge, be sure to wear a
wrist strap on your wrist and connect the
earth clip attached on the other side of the
wrist strap to the chassis frame (metal
part) before starting operation.”.

(1)-1 <Confirm wearing wrist strap>

In response to a message, “Did you put on
a wrist strap on your wrist?”.
Select [Yes] when wrist strap is on your
wrist.
Select [No] when there is no wrist strap on
your wrist.
When [No] is selected (CL), go to Step (1)-
2.

(1)-2
In response to a message, “This operation
cannot be excuted, because the wrist strap
has not been worn. Do you want to stop
this process?
[Yes]: This processing will be stopped.
[No]: This confirming message will
appear.”
When [Yes] is selected (CL), the routine
is returned to Step (2) on page INST03-07-50.
When [No] is selected (CL), returned to Step (1).

INST03-07-100
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-110

(2) <Confirmation on the final charge day>

• When you do increase Cache PCB:
Select (CL) [Yes] in response to “Check
the last charged dates described in the
batteries. Are the last charged dates for
all of the batteries that are target to be
added indicated within six months?”
Go to Step (5).
When [No] is selected (CL), go to Step (3).

• When you do not increase Cache PCB:

Go to Step (5).

(3)
“The backup cannot be ensured with the
battery of last charged date is more than
six months ago. To continue this process,
the maximum 135 minutes of
maintenance hour is required to add to the
usual maintenance hour. Do you want to
stop this process?”

When [Yes] is selected (CL), returns to

INST03-07-50 Step (2).
When [No] is selected (CL), go to Step (4).

(4) <Input password>

Enter the password and select (CL) [OK].

CAUTION
This is a special (exceptional) operation that can cause a serious failure such as a
system down or a data loss if a wrong part to be removed is selected, and requires an
input of a password. Ask the technical support division about the appropriateness of the
operation, and input the password after getting an approval of executing the operation.

INST03-07-110
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-120

(5) <Starting the addition>

In response to a message, “After you
select [Yes], you cannot cancel this
operation. Are you sure you want to
continue this operation?
(Note) Do not install the components for
upgrading the system at this time.”, select
(CL) [Yes].
When [No] is selected (CL), the routine is
returned to Step (2) on page INST03-07-50.

(6) <Confirm>
Select (CL) [OK] in response to “When
the installation failed, you have to
perform installation parts removal and
then perform a second installation by SVP
guidance. You have to follow the SVP
message for performing these recovery
operations. Never remove any parts and
cables without SVP instructions. If you
do not follow the SVP message and
remove them, the subsystem could be crash.”

(7) <Confirm removing MPB>

Select (CL) [OK] in response to “If the
MPBs(MPB-nnn MPB-nnn) was already
installed before this message appears, you
have to check the location of the MPBs,
and then you have to remove it. When
you confirmed that the MPBs was already
removed or not installed, click [OK]
button.
(Note) Please do not install the MPBs yet.”

INST03-07-120
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-130

(8) <HUBBOX Installation Operation>

When installation of the HUBBOX is
required, a message, “Install the
HUBBOX (HUBBOX-nn). After the
operation has completed, select [OK].” is
displayed.

• When the message is displayed, install

the hardware component following the procedure for installing the HUB Kit.
When HUBBOX-10 is displayed, check that the HUBBOX-10 is installed. The
HUBBOX-10 is standard installed in the DKC-1, so installation procedure of it is not
necessary.
• When the message is not displayed, go to “4-2 Add Backup Module”.

NOTE: Do not select (CL) [OK] by mistake before installing the part(s) to be added in the
storage system.

INST03-07-130
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-140

3. Installation Procedure of HUB

Installation Condition
The HUB (DKC-F810I-HUB) is an indispensable option that is to be installed when the
storage system configuration is one of the following.

In case of DKC-0
 Addition of the first set (HUBBOX-01)
• The HUBBOX-01 is required to be installed when the MPB is installed in the Option 2
(1PF/2PF) or Option 3 (1PE/2PE) MPB slots.
However, it is not necessary to be installed when two sets of the DKC-F810I-SVP are
installed.

In case of DKC-1
 HUBBOX-10
• The HUBBOX-10 is standard installed in the DKC-1. (An included option of the CBXB)
 Addition of the second set (HUBBOX-11)
• The HUBBOX-11 is required to be installed when the MPB is installed in the Option 6
(1PM/2PM) or Option 7 (1PL/2PL) MPB slots.

NOTICE: Be sure to wear your wrist strap and attach to ground prior to performing the
following work. This will ensure that the IC and LSI on the PCB are protected
from static electricity.

INST03-07-140
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-150

3-1 Installation of HUBBOX

a. Loosen the two screws of the HUBBOX slot and remove the dummy plate.

HUBBOX-01 HUBBOX-11
HUBBOX-10 (*1)

Rear View of DKC-0 Rear View of DKC-1

*1: Standard equipment

(Included option of CBXB)

DKC-x

Screw

Dummy Plate

Screw
Fig. 3.7.1-1 Removal of Dummy Plate

INST03-07-150
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-160

b. Install the HUBBOX and tighten the two screws.

NOTICE: Confirm the vertical direction of the HUBBOX. If the direction is wrong, the
HUBBOX will not be ON.

Rear View
of DKC

HUBBOX

Lever

Screw

Lever
Screw

Top Side

Bottom Side Front View of HUBBOX

Fig. 3.7.1-2 Installation of HUBBOX

INST03-07-160
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-170

3-2 Storage of Dummy Plate

a. Loosen the three screws  on the front side of the DKC and remove the cable cover.
b. Loosen the screw  and remove the accessory box.
c. Put the removed dummy plate in the accessory box.
d. Put the accessory box in place and fix it with the screw .
e. Put the cable cover in place and fix it with the three screws .

Front View of DKC

Dummy Plate

DKC

Accessory Box

Screw 
Front View Screw 

Screw 

Cable Cover

Fig. 3.7.1-3 Storage of Dummy Plate

INST03-07-170
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-180

4. Backup Module
4-1
When a message,“Install the HUBBOX
(HUBBOX-nn). After the operation has
completed, select [OK].” is displayed,
select (CL) the [OK] button.

4-2 Add Backup Module

(1) Confirmation of Backup Module addition
When a message, “Insert the BKM-nnn
BKM-nnn and then select [OK].” is
displayed.

(Eg. BKM-1BC, BKM-2BC)

INST03-07-180
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-190

(2) Install the BKM on the Cluster 1.

(2)-1 Remove the screw of the option BKM and remove the cover.

Screw
Cover

BKM

Fig. 3.7.1-4 Removal of Cover

(2)-2 Install the option CFM to the BKM and tighten it with the two screws.
(2)-3 Attach the cover to the BKM and tighten it with the screw.

CFM

Screw

BKM

Screw

Fig. 3.7.1-5 Attachment of CFM

INST03-07-190
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-200

(2)-4 If the cables are attached to the BKMs, check that the screws to secure the BKMs are
tightened.
If the cables are not attached to the BKMs, go to Step (2)-6.
NOTE: If the screw is loose, the BKM may be extracted when the cables or the locking
clamp is moved.
(2)-5 Open the four locking clamps and move all the cables to where they cannot obstruct
insertion of the BKM.

BKM Screw Cable

Front View of
DKC
Locking Clamp
Fig. 3.7.1-6 Moving Cables

INST03-07-200
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-210

(2)-6 Loosen the screw and remove the dummy plate.

(2)-7 Install the BKM to the DKC and tighten the screw.
(2)-8 If the cables were moved aside in Step (2)-5, put them back in place.

Main Edge Connector

PCB NOTICE: • Check that the main edge connector of the PCB has
no deformation, damage or sticking of dust before
installing the PCB. (See INST03-01-80)
• When installing the PCB, hold the top and bottom of
the PCB with both hands, and insert it straight not to
contact the neighboring PCB.

2BD 2BC 1BC 1BD 2BB 2BA 1BA 1BB

Front View of DKC-1 Front View of DKC-0

DKC

BKM

Screw
Lever

Screw

Dummy Plate

Fig. 3.7.1-7 Installation of BKM

INST03-07-210
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-220

(3) Install the BKM on the Cluster 2.

(3)-1 Remove the screw of the option BKM and remove the cover.

Screw
Cover

BKM

Fig. 3.7.1-8 Removal of Cover

(3)-2 Install the option CFM to the BKM and tighten it with the two screws.
(3)-3 Attach the cover to the BKM and tighten it with the screw.

CFM

Screw

BKM

Screw

Fig. 3.7.1-9 Attachment of CFM

INST03-07-220
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-230

(3)-4 If the cables are attached to the BKMs, check that the screws to secure the BKMs are
tightened.
If the cables are not attached to the BKMs, go to Step (3)-6.
NOTE: If the screw is loose, the BKM may be extracted when the cables or the locking
clamp is moved.
(3)-5 Open the four locking clamps and move all the cables to where they cannot obstruct
insertion of the BKM.

BKM Screw Cable

Front View of
DKC
Locking Clamp
Fig. 3.7.1-10 Moving Cables

INST03-07-230
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-240

(3)-6 Loosen the screw and remove the dummy plate.

(3)-7 Install the BKM to the DKC and tighten the screw.
(3)-8 If the cables were moved aside in Step (3)-5, put them back in place.

Main Edge Connector

PCB NOTICE: • Check that the main edge connector of the PCB has
no deformation, damage or sticking of dust before
installing the PCB. (See INST03-01-80)
• When installing the PCB, hold the top and bottom of
the PCB with both hands, and insert it straight not to
contact the neighboring PCB.

2BD 2BC 1BC 1BD 2BB 2BA 1BA 1BB

Front View of DKC-1 Front View of DKC-0

DKC

BKM

Screw
Lever

Screw

Dummy Plate

Fig. 3.7.1-11 Installation of BKM

INST03-07-240
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-250

(3)-9 Store the Dummy Plates.

a. Loosen the three screws  on the front side of the DKC and remove the cable cover.
b. Loosen the screw  and remove the accessory box.
c. Put the dummy plates that were removed in the accessory box.
d. Put the accessory box in place and fix it with the screw .
e. Put the cable cover in place and fix it with the three screws .

Front View of DKC

Dummy
Plate

DKC

Accessory Box

Screw 
Front View Screw 

Screw 

Cable Cover

Fig. 3.7.1-12 Storage of Dummy Plates

INST03-07-250
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-260

(4) Confirmation of Backup Module addition

When a message, “Insert the BKM-nnn
BKM-nnn and then select [OK].” is
displayed, select (CL) the [OK] button.

(Eg. BKM-1BC, BKM-2BC)

INST03-07-260
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-270

5. SVP pre procedure (Cache Memory ) (Cluster 1)

(1)
“The Cache Memory PCB is being blocked...”
“Lighting LED of the PCB...” is displayed.

(2) <Perform cache hardware installation>

At this point refrain from pressing the
[OK] button.
When “Replace or insert the Cache
Memory PCB(s)(Memory) of cluster-1.
When completed, please press OK.” is
displayed, install hardware components
according to the cache hardware
installation procedure.

Make sure of the installation location and

size of the module to be added and insert
the correct module in the correct location.
(The Shared Memory capacity may be
changed at the same time, depending on the set Cache Memory capacity.)

INST03-07-270
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-280

6. Install the Cache Memory on the cluster 1

NOTICE: Be sure to wear your wrist strap and attach to ground prior to performing the
following work. This will ensure that the IC and LSI on the PCB are protected
from static electricity.

6-1 Insert the CM Modules.

a. Loosen the screw and remove the cover.

Screw

CM PCB

Cover

Fig. 3.7.1-13 Removal of Cover

INST03-07-280
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-290

b. Remove the dust covers that match the required Cache Memory capacity referring to Fig.
3.7.1-14, Fig. 3.7.1-15, Table 3.7.1-1 through Table 3.7.1-4.
c. Insert the CM Modules that match the required Cache Memory capacity.
d. Attach the cover and tighten the screw. (Refer to Fig. 3.7.1-13.)

CM Module Location of DKC-1

Cluster 1 (CACHE-1CC/1CD)

Removal of Dust Cover

A CM PCB Dust Cover

(WP840-A) Socket
PCB
Viewed from A

CACHE-1CC (Option 2) CACHE-1CD (Option 3)

CM1P: *18 CM1P: *26

CM5P: *22 CM5P: *30
CM3P: *20 CM3P: *28
CM7P: *24 CM7P: *32

CM6P: *23 CM6P: *31

CM2P: *19 CM2P: *27
CM4P: *21 CM4P: *29
CM0P: *17 CM0P: *25

NOTE: The cache memory module location *17 through *32 correspond to the CM
Location listed in Table 3.7.1-1 through Table 3.7.1-4.
Fig. 3.7.1-14 Inserting Location of the CM Module

INST03-07-290
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-300


Memory Module 
 Lever
Cut

Socket

Projection
inside the slot

Installation
 Position the cut of the memory module with the projection inside the slot, and place the memory module
on the socket.
 Hold both ends of the memory module by the fingers, and fit it into the socket.
 Make sure that the lever is firmly fitted in the memory module.

NOTICE: Do not put intense pressure on the CM Module to the extent that the PCB
greatly bends after the CM Module is secured with the levers in installation
procedure of the CM Module. The PCB may be damaged when intense
pressure is applied.

Memory Module Appearance

There are two types of memory modules. One has a heat spreader and the other has no heat spreaders.
Both memory modules can be used because they are compatible with each other.

Memory Module Memory Module

(with Heat Spreader) (without Heat Spreader)

Heat Spreader

Fig. 3.7.1-15 Insertion of Memory Module

INST03-07-300
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-310

Table 3.7.1-1 Cache memory capacity and number of necessary options 

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM16G CPEX BKMS/ BMM128/
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD BKML BMM256
1 32GB *1 — — — 2 0 1 2
2 64GB *1,*2 — — — 4 0 1 2
3 96GB *1-*3 — — — 6 0 1 2
4 128GB *1-*4 — — — 8 0 1 2
5 160GB *1-*5 — — — 10 0 1 2
6 192GB *1-*7 — — — 12 0 1 2
7 224GB *1-*8 — — — 14 0 1 2
8 256GB *1-*8 — — — 16 0 1 2
9 288GB *1-*8 *9 — — 18 1 2 4
10 320GB *1-*8 *9,*10 — — 20 1 2 4
11 356GB *1-*8 *9-*11 — — 22 1 2 4
12 384GB *1-*8 *9-*12 — — 24 1 2 4
13 416GB *1-*8 *9-*13 — — 26 1 2 4
14 448GB *1-*8 *9-*14 — — 28 1 2 4
15 480GB *1-*8 *9-*15 — — 30 1 2 4
16 512GB *1-*8 *9-*16 — — 32 1 2 4
17 576GB *1-*8 *9-*16 *17 *25 36 2 4 8
18 608GB *1-*8 *9-*16 *17,*18 *25 38 2 4 8
19 640GB *1-*8 *9-*16 *17,*18 *25,*26 40 2 4 8
20 672GB *1-*8 *9-*16 *17-*19 *25,*26 42 2 4 8
21 704GB *1-*8 *9-*16 *17-*19 *25-*27 44 2 4 8
22 736GB *1-*8 *9-*16 *17-*20 *25-*27 46 2 4 8
23 768GB *1-*8 *9-*16 *17-*20 *25-*28 48 2 4 8
24 800GB *1-*8 *9-*16 *17-*21 *25-*28 50 2 4 8
25 832GB *1-*8 *9-*16 *17-*21 *25-*29 52 2 4 8
26 864GB *1-*8 *9-*16 *17-*22 *25-*29 54 2 4 8
27 896GB *1-*8 *9-*16 *17-*22 *25-*30 56 2 4 8
28 928GB *1-*8 *9-*16 *17-*23 *25-*30 58 2 4 8
29 960GB *1-*8 *9-*16 *17-*23 *25-*31 60 2 4 8
30 992GB *1-*8 *9-*16 *17-*24 *25-*31 62 2 4 8
31 1024GB *1-*8 *9-*16 *17-*24 *25-*32 64 2 4 8

NOTE 1: The above numbers (*17 through *32) represent the CM Module locations shown in
Fig. 3.7.1-14 or Fig. 3.7.1-18.

INST03-07-310
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-320

Table 3.7.1-2 Cache memory capacity and number of necessary options 

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM32G CPEX BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 128 256
1 64GB *1 — — — 2 0 1 0 2 0
2 128GB *1,*2 — — — 4 0 1 0 2 0
3 192GB *1-*3 — — — 6 0 1 0 2 0
4 256GB *1-*4 — — — 8 0 1 0 2 0
5 320GB *1-*5 — — — 10 0 0 1 0 2
6 384GB *1-*7 — — — 12 0 0 1 0 2
7 448GB *1-*8 — — — 14 0 0 1 0 2
8 512GB *1-*8 — — — 16 0 0 1 0 2
9 576GB *1-*8 *9 — — 18 1 1 1 2 2
10 640GB *1-*8 *9,*10 — — 20 1 1 1 2 2
11 704GB *1-*8 *9-*11 — — 22 1 1 1 2 2
12 768GB *1-*8 *9-*12 — — 24 1 1 1 2 2
13 832GB *1-*8 *9-*13 — — 26 1 0 2 0 4
14 896GB *1-*8 *9-*14 — — 28 1 0 2 0 4
15 960GB *1-*8 *9-*15 — — 30 1 0 2 0 4
16 1024GB *1-*8 *9-*16 — — 32 1 0 2 0 4
17 1152GB *1-*8 *9-*16 *17 *25 36 2 2 2 4 4
18 1216GB *1-*8 *9-*16 *17,*18 *25 38 2 2 2 4 4
19 1280GB *1-*8 *9-*16 *17,*18 *25,*26 40 2 2 2 4 4
20 1344GB *1-*8 *9-*16 *17-*19 *25,*26 42 2 2 2 4 4
21 1408GB *1-*8 *9-*16 *17-*19 *25-*27 44 2 2 2 4 4
22 1472GB *1-*8 *9-*16 *17-*20 *25-*27 46 2 2 2 4 4
23 1536GB *1-*8 *9-*16 *17-*20 *25-*28 48 2 2 2 4 4
24 1600GB *1-*8 *9-*16 *17-*21 *25-*28 50 2 1 3 2 6
25 1664GB *1-*8 *9-*16 *17-*21 *25-*29 52 2 0 4 0 8
26 1728GB *1-*8 *9-*16 *17-*22 *25-*29 54 2 0 4 0 8
27 1792GB *1-*8 *9-*16 *17-*22 *25-*30 56 2 0 4 0 8
28 1856GB *1-*8 *9-*16 *17-*23 *25-*30 58 2 0 4 0 8
29 1920GB *1-*8 *9-*16 *17-*23 *25-*31 60 2 0 4 0 8
30 1984GB *1-*8 *9-*16 *17-*24 *25-*31 62 2 0 4 0 8
31 2048GB *1-*8 *9-*16 *17-*24 *25-*32 64 2 0 4 0 8

NOTE 1: The above numbers (*17 through *32) represent the CM Module locations shown in
Fig. 3.7.1-14 or Fig. 3.7.1-18.

INST03-07-320
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-330

Table 3.7.1-3 Cache memory capacity and number of necessary options 

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 16G 128 256
1 64 *1 — *17 — 4 0 1 0 2 — 4 —
2 96 *1,*2 — *17 — 6 0 1 0 2 — 4 —
3 128 *1 *9 *17 *25 8 2 1 1 4 — 8 —
4 128 *1,*2 — *17,*18 — 8 0 1 0 2 — 4 —
5 128 *1-*3 — *17 — 8 0 1 0 2 — 4 —
6 160 *1,*2 *9 *17 *25 10 2 1 1 4 — 8 —
7 160 *1-*3 — *17,*18 — 10 0 1 0 2 — 4 —
8 160 *1-*4 — *17 — 10 0 1 0 2 — 4 —
9 192 *1,*2 *9 *17,*18 *25 12 2 1 1 4 — 8 —
10 192 *1,*2 *9,*10 *17 *25 12 2 1 1 4 — 8 —
11 192 *1-*3 — *17-*19 — 12 0 1 0 2 — 4 —
12 192 *1-*3 *9 *17 *25 12 2 1 1 4 — 8 —
13 192 *1-*4 — *17,*18 — 12 0 1 0 2 — 4 —
14 192 *1-*5 — *17 — 12 0 1 0 2 — 4 —
15 224 *1,*2 *9,*10 *17,*18 *25 14 2 1 1 4 — 8 —
16 224 *1-*3 *9,*10 *17 *25 14 2 1 1 4 — 8 —
17 224 *1-*4 *9 *17 *25 14 2 1 1 4 — 8 —
18 224 *1-*5 — *17,*18 — 14 0 1 0 2 — 4 —
19 224 *1-*6 — *17 — 14 0 1 0 2 — 4 —
20 256 *1,*2 *9,*10 *17,*18 *25,*26 16 2 1 1 4 — 8 —
21 256 *1-*3 *9 *17-*19 *25 16 2 1 1 4 — 8 —
22 256 *1-*3 *9,*10 *17,*18 *25 16 2 1 1 4 — 8 —
23 256 *1-*3 *9-*11 *17 *25 16 2 1 1 4 — 8 —
24 256 *1-*4 — *17-*20 — 16 0 1 0 2 — 4 —
25 256 *1-*4 *9,*10 *17 *25 16 2 1 1 4 — 8 —
26 256 *1-*5 — *17-*19 — 16 0 1 0 2 — 4 —
27 256 *1-*5 *9 *17 *25 16 2 1 1 4 — 8 —
28 256 *1-*6 — *17,*18 — 16 0 1 0 2 — 4 —
29 256 *1-*7 — *17 — 16 0 1 0 2 — 4 —
30 288 *1-*3 *9,*10 *17,*18 *25,*26 18 2 1 1 4 — 8 —
31 288 *1-*3 *9,*10 *17-*19 *25 18 2 1 1 4 — 8 —
32 288 *1-*3 *9-*11 *17,*18 *25 18 2 1 1 4 — 8 —
33 288 *1-*4 *9,*10 *17,*18 *25 18 2 1 1 4 — 8 —
34 288 *1-*4 *9-*11 *17 *25 18 2 1 1 4 — 8 —
35 288 *1-*5 — *17-*20 — 18 0 1 0 2 — 4 —
(To be continued)

INST03-07-330
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-340

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 16G 128 256
36 288 *1-*5 *9,*10 *17 *25 18 2 1 1 4 — 8 —
37 288 *1-*6 — *17-*19 — 18 0 1 0 2 — 4 —
38 288 *1-*6 *9 *17 *25 18 2 1 1 4 — 8 —
39 288 *1-*7 — *17,*18 — 18 0 1 0 2 — 4 —
40 288 *1-*8 — *17 — 18 0 1 0 2 — 4 —
41 320 *1-*3 *9,*10 *17-*19 *25,*26 20 2 1 1 4 — 8 —
42 320 *1-*3 *9-*11 *17,*18 *25,*26 20 2 1 1 4 — 8 —
43 320 *1-*3 *9-*11 *17-*19 *25 20 2 1 1 4 — 8 —
44 320 *1-*4 *9 *17-*20 *25 20 2 1 1 4 — 8 —
45 320 *1-*4 *9,*10 *17,*18 *25,*26 20 2 1 1 4 — 8 —
46 320 *1-*4 *9-*11 *17,*18 *25 20 2 1 1 4 — 8 —
47 320 *1-*4 *9-*12 *17 *25 20 2 1 1 4 — 8 —
48 320 *1-*5 — *17-*21 — 20 0 1 0 2 — 4 —
49 320 *1-*5 *9,*10 *17,*18 *25 20 2 1 1 4 — 8 —
50 320 *1-*5 *9-*11 *17 *25 20 2 1 1 4 — 8 —
51 320 *1-*6 — *17-*20 — 20 0 1 0 2 — 4 —
52 320 *1-*6 *9,*10 *17 *25 20 2 1 1 4 — 8 —
53 320 *1-*7 — *17-*19 — 20 0 1 0 2 — 4 —
54 320 *1-*7 *9 *17 *25 20 2 1 1 4 — 8 —
55 320 *1-*8 — *17,*18 — 20 0 1 0 2 — 4 —
56 352 *1-*3 *9-*11 *17-*19 *25,*26 22 2 1 1 4 — 8 —
57 352 *1-*4 *9,*10 *17-*20 *25 22 2 1 1 4 — 8 —
58 352 *1-*4 *9-*11 *17,*18 *25,*26 22 2 1 1 4 — 8 —
59 352 *1-*4 *9-*11 *17-*19 *25 22 2 1 1 4 — 8 —
60 352 *1-*4 *9-*12 *17,*18 *25 22 2 1 1 4 — 8 —
61 352 *1-*5 *9,*10 *17,*18 *25,*26 22 2 1 1 4 — 8 —
62 352 *1-*5 *9-*11 *17,*18 *25 22 2 1 1 4 — 8 —
63 352 *1-*5 *9-*12 *17 *25 22 2 1 1 4 — 8 —
64 352 *1-*6 — *17-*21 — 22 0 1 0 2 — 4 —
65 352 *1-*6 *9,*10 *17,*18 *25 22 2 1 1 4 — 8 —
66 352 *1-*6 *9-*11 *17 *25 22 2 1 1 4 — 8 —
67 352 *1-*7 — *17-*20 — 22 0 1 0 2 — 4 —
68 352 *1-*7 *9,*10 *17 *25 22 2 1 1 4 — 8 —
69 352 *1-*8 — *17-*19 — 22 0 1 0 2 — 4 —
70 352 *1-*8 *9 *17 *25 22 2 1 1 4 — 8 —
(To be continued)

INST03-07-340
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-350

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 16G 128 256
71 384 *1-*3 *9-*11 *17-*19 *25-*27 24 2 1 1 4 — 8 —
72 384 *1-*4 *9,*10 *17-*20 *25,*26 24 2 1 1 4 — 8 —
73 384 *1-*4 *9-*11 *17-*19 *25,*26 24 2 1 1 4 — 8 —
74 384 *1-*4 *9-*11 *17-*20 *25 24 2 1 1 4 — 8 —
75 384 *1-*4 *9-*12 *17,*18 *25,*26 24 2 1 1 4 — 8 —
76 384 *1-*4 *9-*12 *17-*19 *25 24 2 1 1 4 — 8 —
77 384 *1-*5 32 *17-*21 *25 24 2 1 1 4 — 8 —
78 384 *1-*5 *9-*11 *17,*18 *25,*26 24 2 1 1 4 — 8 —
79 384 *1-*5 *9-*11 *17-*19 *25 24 2 1 1 4 — 8 —
80 384 *1-*5 *9-*12 *17,*18 *25 24 2 1 1 4 — 8 —
81 384 *1-*5 *9-*13 *17 *25 24 2 1 1 4 — 8 —
82 384 *1-*6 — *17-*22 — 24 0 1 0 2 — 4 —
83 384 *1-*6 *9,*10 *17,*18 *25,*26 24 2 1 1 4 — 8 —
84 384 *1-*6 *9-*11 *17,*18 *25 24 2 1 1 4 — 8 —
85 384 *1-*6 *9-*12 *17 *25 24 2 1 1 4 — 8 —
86 384 *1-*7 — *17-*21 — 24 0 1 0 2 — 4 —
87 384 *1-*7 *9,*10 *17,*18 *25 24 2 1 1 4 — 8 —
88 384 *1-*7 *9-*11 *17 *25 24 2 1 1 4 — 8 —
89 384 *1-*8 — *17-*20 — 24 0 1 0 2 — 4 —
90 384 *1-*8 *9,*10 *17 *25 24 2 1 1 4 — 8 —
91 416 *1-*4 *9-*11 *17-*19 *25-*27 26 2 1 1 4 — 8 —
92 416 *1-*4 *9-*11 *17-*20 *25,*26 26 2 1 1 4 — 8 —
93 416 *1-*4 *9-*12 *17-*19 *25,*26 26 2 1 1 4 — 8 —
94 416 *1-*4 *9-*12 *17-*20 *25 26 2 1 1 4 — 8 —
95 416 *1-*5 *9,*10 *17-*21 *25 26 2 1 1 4 — 8 —
96 416 *1-*5 *9-*11 *17-*19 *25,*26 26 2 1 1 4 — 8 —
97 416 *1-*5 *9-*12 *17,*18 *25,*26 26 2 1 1 4 — 8 —
98 416 *1-*5 *9-*12 *17-*19 *25 26 2 1 1 4 — 8 —
99 416 *1-*5 *9-*13 *17,*18 *25 26 2 1 1 4 — 8 —
100 416 *1-*6 *9-*11 *17,*18 *25,*26 26 2 1 1 4 — 8 —
101 416 *1-*6 *9-*11 *17-*19 *25 26 2 1 1 4 — 8 —
102 416 *1-*6 *9-*12 *17,*18 *25 26 2 1 1 4 — 8 —
103 416 *1-*6 *9-*13 *17 *25 26 2 1 1 4 — 8 —
104 416 *1-*7 — *17-*22 — 26 0 1 0 2 — 4 —
105 416 *1-*7 *9,*10 *17,*18 *25,*26 26 2 1 1 4 — 8 —
(To be continued)

INST03-07-350
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-360

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 16G 128 256
106 416 *1-*7 *9-*11 *17,*18 *25 26 2 1 1 4 — 8 —
107 416 *1-*7 *9-*12 *17 *25 26 2 1 1 4 — 8 —
108 416 *1-*8 — *17-*21 — 26 0 1 0 2 — 4 —
109 416 *1-*8 *9-*11 *17 *25 26 2 1 1 4 — 8 —
110 448 *1-*4 *9-*11 *17-*20 *25-*27 28 2 1 1 4 — 8 —
111 448 *1-*4 *9-*12 *17-*19 *25-*27 28 2 1 1 4 — 8 —
112 448 *1-*4 *9-*12 *17-*20 *25,*26 28 2 1 1 4 — 8 —
113 448 *1-*5 *9,*10 *17-*21 *25,*26 28 2 1 1 4 — 8 —
114 448 *1-*5 *9-*11 *17-*19 *25-*27 28 2 1 1 4 — 8 —
115 448 *1-*5 *9-*11 *17-*21 *25 28 2 1 1 4 — 8 —
116 448 *1-*5 *9-*12 *17-*19 *25,*26 28 2 1 1 4 — 8 —
117 448 *1-*5 *9-*12 *17-*20 *25 28 2 1 1 4 — 8 —
118 448 *1-*5 *9-*13 *17,*18 *25,*26 28 2 1 1 4 — 8 —
119 448 *1-*5 *9-*13 *17-*19 *25 28 2 1 1 4 — 8 —
120 448 *1-*6 *9 *17-*22 *25 28 2 1 1 4 — 8 —
121 448 *1-*6 *9-*11 *17-*19 *25,*26 28 2 1 1 4 — 8 —
122 448 *1-*6 *9-*12 *17,*18 *25,*26 28 2 1 1 4 — 8 —
123 448 *1-*6 *9-*12 *17-*19 *25 28 2 1 1 4 — 8 —
124 448 *1-*6 *9-*13 *17,*18 *25 28 2 1 1 4 — 8 —
125 448 *1-*6 *9-*14 *17 *25 28 2 1 1 4 — 8 —
126 448 *1-*7 — 224 — 28 0 1 0 2 — 4 —
127 448 *1-*7 *9-*11 *17,*18 *25,*26 28 2 1 1 4 — 8 —
128 448 *1-*7 *9-*11 *17-*19 *25 28 2 1 1 4 — 8 —
129 448 *1-*7 *9-*12 *17,*18 *25 28 2 1 1 4 — 8 —
130 448 *1-*7 *9-*13 *17 *25 28 2 1 1 4 — 8 —
131 448 *1-*8 — *17-*22 — 28 0 1 0 2 — 4 —
132 448 *1-*8 *9-*12 *17 *25 28 2 1 1 4 — 8 —
133 480 *1-*4 *9-*12 *17-*20 *25-*27 30 2 1 1 4 — 8 —
134 480 *1-*5 *9-*11 *17-*21 *25,*26 30 2 1 1 4 — 8 —
135 480 *1-*5 *9-*12 *17-*19 *25-*27 30 2 1 1 4 — 8 —
136 480 *1-*5 *9-*12 *17-*20 *25,*26 30 2 1 1 4 — 8 —
137 480 *1-*5 *9-*12 *17-*21 *25 30 2 1 1 4 — 8 —
138 480 *1-*5 *9-*13 *17-*19 *25,*26 30 2 1 1 4 — 8 —
139 480 *1-*5 *9-*13 *17-*20 *25 30 2 1 1 4 — 8 —
140 480 *1-*6 *9,*10 *17-*22 *25 30 2 1 1 4 — 8 —
(To be continued)

INST03-07-360
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-370

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 16G 128 256
141 480 *1-*6 *9-*11 *17-*19 *25-*27 30 2 1 1 4 — 8 —
142 480 *1-*6 *9-*12 *17-*19 *25,*26 30 2 1 1 4 — 8 —
143 480 *1-*6 *9-*12 *17-*20 *25 30 2 1 1 4 — 8 —
144 480 *1-*6 *9-*13 *17,*18 *25,*26 30 2 1 1 4 — 8 —
145 480 *1-*6 *9-*13 *17-*19 *25 30 2 1 1 4 — 8 —
146 480 *1-*6 *9-*14 *17,*18 *25 30 2 1 1 4 — 8 —
147 480 *1-*7 *9-*11 *17-*19 *25,*26 30 2 1 1 4 — 8 —
148 480 *1-*7 *9-*12 *17,*18 *25,*26 30 2 1 1 4 — 8 —
149 480 *1-*7 *9-*12 *17-*19 *25 30 2 1 1 4 — 8 —
150 480 *1-*7 *9-*13 *17,*18 *25 30 2 1 1 4 — 8 —
151 480 *1-*8 — *17-*23 — 30 0 1 0 2 — 4 —
152 480 *1-*8 *9-*13 *17 *25 30 2 1 1 4 — 8 —
153 512 *1-*4 *9-*12 *17-*20 128 32 2 1 1 4 — 8 —
154 512 *1-*5 *9-*11 *17-*21 *25-*27 32 2 1 1 4 — 8 —
155 512 *1-*5 *9-*12 *17-*20 *25-*27 32 2 1 1 4 — 8 —
156 512 *1-*5 *9-*12 *17-*21 *25,*26 32 2 1 1 4 — 8 —
157 512 *1-*5 *9-*13 *17-*19 *25-*27 32 2 1 1 4 — 8 —
158 512 *1-*5 *9-*13 *17-*20 *25,*26 32 2 1 1 4 — 8 —
159 512 *1-*5 *9-*13 *17-*21 *25 32 2 1 1 4 — 8 —
160 512 *1-*6 *9,*10 *17-*22 *25,*26 32 2 1 1 4 — 8 —
161 512 *1-*6 *9-*11 *17-*22 *25 32 2 1 1 4 — 8 —
162 512 *1-*6 *9-*12 *17-*19 *25-*27 32 2 1 1 4 — 8 —
163 512 *1-*6 *9-*12 *17-*20 *25,*26 32 2 1 1 4 — 8 —
164 512 *1-*6 *9-*13 *17-*19 *25,*26 32 2 1 1 4 — 8 —
165 512 *1-*6 *9-*13 *17-*20 *25 32 2 1 1 4 — 8 —
166 512 *1-*6 *9-*14 *17,*18 *25,*26 32 2 1 1 4 — 8 —
167 512 *1-*6 *9-*14 *17-*19 *25 32 2 1 1 4 — 8 —
168 512 *1-*7 *9 *17-*23 *25 32 2 1 1 4 — 8 —
169 512 *1-*7 *9-*11 *17-*19 *25-*27 32 2 1 1 4 — 8 —
170 512 *1-*7 *9-*12 *17-*19 *25,*26 32 2 1 1 4 — 8 —
171 512 *1-*7 *9-*12 *17-*20 *25 32 2 1 1 4 — 8 —
172 512 *1-*7 *9-*13 *17,*18 *25,*26 32 2 1 1 4 — 8 —
173 512 *1-*7 *9-*13 *17-*19 *25 32 2 1 1 4 — 8 —
174 512 *1-*7 *9-*15 *17 *25 32 2 1 1 4 — 8 —
175 512 *1-*8 — *17-*24 — 32 0 1 0 2 — 4 —
(To be continued)

INST03-07-370
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-380

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 16G 128 256
176 512 *1-*8 *9-*14 *17 *25 32 2 1 1 4 — 8 —
177 544 *1-*5 *9-*12 *17-*20 *25-*28 34 2 1 1 4 — 8 —
178 544 *1-*5 *9-*12 *17-*21 *25-*27 34 2 1 1 4 — 8 —
179 544 *1-*5 *9-*13 *17-*20 *25-*27 34 2 1 1 4 — 8 —
180 544 *1-*5 *9-*13 *17-*21 *25,*26 34 2 1 1 4 — 8 —
181 544 *1-*6 *9-*11 *17-*22 *25,*26 34 2 1 1 4 — 8 —
182 544 *1-*6 *9-*12 *17-*20 *25-*27 34 2 1 1 4 — 8 —
183 544 *1-*6 *9-*12 *17-*22 *25 34 2 1 1 4 — 8 —
184 544 *1-*6 *9-*13 *17-*19 *25-*27 34 2 1 1 4 — 8 —
185 544 *1-*6 *9-*13 *17-*20 *25,*26 34 2 1 1 4 — 8 —
186 544 *1-*6 *9-*13 *17-*21 *25 34 2 1 1 4 — 8 —
187 544 *1-*6 *9-*14 *17-*19 *25,*26 34 2 1 1 4 — 8 —
188 544 *1-*6 *9-*14 *17-*20 *25 34 2 1 1 4 — 8 —
189 544 *1-*7 *9,*10 *17-*23 *25 34 2 1 1 4 — 8 —
190 544 *1-*7 *9-*12 *17-*19 *25-*27 34 2 1 1 4 — 8 —
191 544 *1-*7 *9-*12 *17-*20 *25,*26 34 2 1 1 4 — 8 —
192 544 *1-*7 *9-*13 *17-*19 *25,*26 34 2 1 1 4 — 8 —
193 544 *1-*7 *9-*13 *17-*20 *25 34 2 1 1 4 — 8 —
194 544 *1-*7 *9-*15 *17,*18 *25 34 2 1 1 4 — 8 —
195 544 *1-*8 *9-*15 *17 *25 34 2 1 1 4 — 8 —
196 576 *1-*5 *9-*12 *17-*21 *25-*28 36 2 1 1 4 — 8 —
197 576 *1-*5 *9-*13 *17-*20 *25-*28 36 2 1 1 4 — 8 —
198 576 *1-*5 *9-*13 *17-*21 *25-*27 36 2 1 1 4 — 8 —
199 576 *1-*6 *9-*11 *17-*22 *25-*27 36 2 1 1 4 — 8 —
200 576 *1-*6 *9-*12 *17-*20 *25-*28 36 2 1 1 4 — 8 —
201 576 *1-*6 *9-*12 *17-*22 *25,*26 36 2 1 1 4 — 8 —
202 576 *1-*6 *9-*13 *17-*20 *25-*27 36 2 1 1 4 — 8 —
203 576 *1-*6 *9-*13 *17-*21 *25,*26 36 2 1 1 4 — 8 —
204 576 *1-*6 *9-*13 *17-*22 *25 36 2 1 1 4 — 8 —
205 576 *1-*6 *9-*13 *17-*22 *25 36 2 1 1 4 — 8 —
206 576 *1-*6 *9-*14 *17-*19 *25-*27 36 2 1 1 4 — 8 —
207 576 *1-*6 *9-*14 *17-*20 *25,*26 36 2 1 1 4 — 8 —
208 576 *1-*6 *9-*14 *17-*21 *25 36 2 1 1 4 — 8 —
209 576 *1-*7 *9,*10 *17-*23 *25,*26 36 2 1 1 4 — 8 —
210 576 *1-*7 *9-*11 *17-*23 *25 36 2 1 1 4 — 8 —
(To be continued)

INST03-07-380
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-390

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 16G 128 256
211 576 *1-*7 *9-*12 *17-*20 *25-*27 36 2 1 1 4 — 8 —
212 576 *1-*7 *9-*13 *17-*19 *25-*27 36 2 1 1 4 — 8 —
213 576 *1-*7 *9-*13 *17-*20 *25,*26 36 2 1 1 4 — 8 —
214 576 *1-*7 *9-*13 *17-*21 *25 36 2 1 1 4 — 8 —
215 576 *1-*7 *9-*15 *17-*19 *25 36 2 1 1 4 — 8 —
216 576 *1-*8 *9 *17-*24 *25 36 2 1 1 4 — 8 —
217 576 *1-*8 *9-*16 *17 *25 36 2 1 1 4 — 8 —
218 608 *1-*5 *9-*13 *17-*21 *25-*28 38 2 1 1 4 — 8 —
219 608 *1-*6 *9-*12 *17-*22 *25-*27 38 2 1 1 4 — 8 —
220 608 *1-*6 *9-*13 *17-*20 *25-*28 38 2 1 1 4 — 8 —
221 608 *1-*6 *9-*13 *17-*21 *25-*27 38 2 1 1 4 — 8 —
222 608 *1-*6 *9-*13 *17-*22 *25,*26 38 2 1 1 4 — 8 —
223 608 *1-*6 *9-*14 *17-*20 *25-*27 38 2 1 1 4 — 8 —
224 608 *1-*6 *9-*14 *17-*21 *25,*26 38 2 1 1 4 — 8 —
225 608 *1-*6 *9-*14 *17-*22 *25 38 2 1 1 4 — 8 —
226 608 *1-*7 *9-*11 *17-*23 *25,*26 38 2 1 1 4 — 8 —
227 608 *1-*7 *9-*12 *17-*20 *25-*28 38 2 1 1 4 — 8 —
228 608 *1-*7 *9-*12 *17-*23 *25 38 2 1 1 4 — 8 —
229 608 *1-*7 *9-*13 *17-*20 *25-*27 38 2 1 1 4 — 8 —
230 608 *1-*7 *9-*13 *17-*21 *25,*26 38 2 1 1 4 — 8 —
231 608 *1-*7 *9-*15 *17-*19 *25,*26 38 2 1 1 4 — 8 —
232 608 *1-*7 *9-*15 *17-*20 *25 38 2 1 1 4 — 8 —
233 608 *1-*8 *9,*10 *17-*24 *25 38 2 1 1 4 — 8 —
234 608 *1-*8 *9-*16 *17,*18 *25 38 2 1 1 4 — 8 —
235 640 *1-*5 *9-*13 *17-*21 *25-*29 40 2 1 1 4 — 8 —
236 640 *1-*6 *9-*12 *17-*22 *25-*28 40 2 1 1 4 — 8 —
237 640 *1-*6 *9-*13 *17-*21 *25-*28 40 2 1 1 4 — 8 —
238 640 *1-*6 *9-*13 *17-*22 *25-*27 40 2 1 1 4 — 8 —
239 640 *1-*6 *9-*14 *17-*20 *25-*28 40 2 1 1 4 — 8 —
240 640 *1-*6 *9-*14 *17-*21 *25-*27 40 2 1 1 4 — 8 —
241 640 *1-*6 *9-*14 *17-*22 *25,*26 40 2 1 1 4 — 8 —
242 640 *1-*7 *9-*11 *17-*23 *25-*27 40 2 1 1 4 — 8 —
243 640 *1-*7 *9-*12 *17-*23 *25,*26 40 2 1 1 4 — 8 —
244 640 *1-*7 *9-*13 *17-*20 *25-*28 40 2 1 1 4 — 8 —
245 640 *1-*7 *9-*13 *17-*21 *25-*27 40 2 1 1 4 — 8 —
(To be continued)

INST03-07-390
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-400

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 16G 128 256
246 640 *1-*7 *9-*13 *17-*23 *25 40 2 1 1 4 — 8 —
247 640 *1-*7 *9-*14 *17-*22 *25 40 2 1 1 4 — 8 —
248 640 *1-*7 *9-*15 *17-*19 *25-*27 40 2 1 1 4 — 8 —
249 640 *1-*7 *9-*15 *17-*20 *25,*26 40 2 1 1 4 — 8 —
250 640 *1-*7 *9-*15 *17-*21 *25 40 2 1 1 4 — 8 —
251 640 *1-*8 *9,*10 *17-*24 *25,*26 40 2 1 1 4 — 8 —
252 640 *1-*8 *9-*11 *17-*24 *25 40 2 1 1 4 — 8 —
253 640 *1-*8 *9-*16 *17-*19 *25 40 2 1 1 4 — 8 —
254 672 *1-*6 *9-*13 *17-*21 *25-*29 42 2 1 1 4 — 8 —
255 672 *1-*6 *9-*13 *17-*22 *25-*28 42 2 1 1 4 — 8 —
256 672 *1-*6 *9-*14 *17-*21 *25-*28 42 2 1 1 4 — 8 —
257 672 *1-*6 *9-*14 *17-*22 *25-*27 42 2 1 1 4 — 8 —
258 672 *1-*7 *9-*12 *17-*23 *25-*27 42 2 1 1 4 — 8 —
259 672 *1-*7 *9-*13 *17-*21 *25-*28 42 2 1 1 4 — 8 —
260 672 *1-*7 *9-*13 *17-*23 *25,*26 42 2 1 1 4 — 8 —
261 672 *1-*7 *9-*14 *17-*22 *25,*26 42 2 1 1 4 — 8 —
262 672 *1-*7 *9-*14 *17-*23 *25 42 2 1 1 4 — 8 —
263 672 *1-*7 *9-*15 *17-*20 *25-*27 42 2 1 1 4 — 8 —
264 672 *1-*7 *9-*15 *17-*21 *25,*26 42 2 1 1 4 — 8 —
265 672 *1-*7 *9-*15 *17-*22 *25 42 2 1 1 4 — 8 —
266 672 *1-*8 *9-*11 *17-*24 *25,*26 42 2 1 1 4 — 8 —
267 672 *1-*8 *9-*12 *17-*24 *25 42 2 1 1 4 — 8 —
268 672 *1-*8 *9-*16 *17-*20 *25 42 2 1 1 4 — 8 —
269 704 *1-*6 *9-*13 *17-*22 *25-*29 44 2 1 1 4 — 8 —
270 704 *1-*6 *9-*14 *17-*21 *25-*29 44 2 1 1 4 — 8 —
271 704 *1-*6 *9-*14 *17-*22 *25-*28 44 2 1 1 4 — 8 —
272 704 *1-*7 *9-*12 *17-*23 *25-*28 44 2 1 1 4 — 8 —
273 704 *1-*7 *9-*13 *17-*21 *25-*29 44 2 1 1 4 — 8 —
274 704 *1-*7 *9-*13 *17-*23 *25-*27 44 2 1 1 4 — 8 —
275 704 *1-*7 *9-*14 *17-*22 *25-*27 44 2 1 1 4 — 8 —
276 704 *1-*7 *9-*14 *17-*23 *25,*26 44 2 1 1 4 — 8 —
277 704 *1-*7 *9-*15 *17-*20 *25-*28 44 2 1 1 4 — 8 —
278 704 *1-*7 *9-*15 *17-*21 *25-*27 44 2 1 1 4 — 8 —
279 704 *1-*7 *9-*15 *17-*22 *25,*26 44 2 1 1 4 — 8 —
280 704 *1-*7 *9-*15 *17-*23 *25 44 2 1 1 4 — 8 —
(To be continued)

INST03-07-400
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-410

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 16G 128 256
281 704 *1-*8 *9-*11 *17-*24 *25-*27 44 2 1 1 4 — 8 —
282 704 *1-*8 *9-*12 *17-*24 *25,*26 44 2 1 1 4 — 8 —
283 704 *1-*8 *9-*13 *17-*24 *25 44 2 1 1 4 — 8 —
284 704 *1-*8 *9-*16 *17-*21 *25 44 2 1 1 4 — 8 —
285 736 *1-*6 *9-*14 *17-*22 *25-*29 46 2 1 1 4 — 8 —
286 736 *1-*7 *9-*13 *17-*23 *25-*28 46 2 1 1 4 — 8 —
287 736 *1-*7 *9-*14 *17-*22 *25-*28 46 2 1 1 4 — 8 —
288 736 *1-*7 *9-*14 *17-*23 *25-*27 46 2 1 1 4 — 8 —
289 736 *1-*7 *9-*15 *17-*21 *25-*28 46 2 1 1 4 — 8 —
290 736 *1-*7 *9-*15 *17-*22 *25-*27 46 2 1 1 4 — 8 —
291 736 *1-*7 *9-*15 *17-*23 *25,*26 46 2 1 1 4 — 8 —
292 736 *1-*8 *9-*12 *17-*24 *25-*27 46 2 1 1 4 — 8 —
293 736 *1-*8 *9-*13 *17-*24 *25,*26 46 2 1 1 4 — 8 —
294 736 *1-*8 *9-*14 *17-*24 *25 46 2 1 1 4 — 8 —
295 736 *1-*8 *9-*16 *17-*22 *25 46 2 1 1 4 — 8 —
296 768 *1-*6 *9-*14 *17-*22 *25-*30 48 2 1 1 4 — 8 —
297 768 *1-*7 *9-*13 *17-*23 *25-*29 48 2 1 1 4 — 8 —
298 768 *1-*7 *9-*14 *17-*22 *25-*29 48 2 1 1 4 — 8 —
299 768 *1-*7 *9-*14 *17-*23 *25-*28 48 2 1 1 4 — 8 —
300 768 *1-*7 *9-*15 *17-*21 *25-*29 48 2 1 1 4 — 8 —
301 768 *1-*7 *9-*15 *17-*22 *25-*28 48 2 1 1 4 — 8 —
302 768 *1-*7 *9-*15 *17-*23 *25-*27 48 2 1 1 4 — 8 —
303 768 *1-*8 *9-*12 *17-*24 *25-*28 48 2 1 1 4 — 8 —
304 768 *1-*8 *9-*13 *17-*24 *25-*27 48 2 1 1 4 — 8 —
305 768 *1-*8 *9-*14 *17-*24 *25,*26 48 2 1 1 4 — 8 —
306 768 *1-*8 *9-*15 *17-*24 *25 48 2 1 1 4 — 8 —
307 768 *1-*8 *9-*16 *17-*23 *25 48 2 1 1 4 — 8 —
308 800 *1-*7 *9-*14 *17-*22 *25-*30 50 2 1 1 4 — 8 —
309 800 *1-*7 *9-*14 *17-*23 *25-*29 50 2 1 1 4 — 8 —
310 800 *1-*7 *9-*15 *17-*22 *25-*29 50 2 1 1 4 — 8 —
311 800 *1-*7 *9-*15 *17-*23 *25-*28 50 2 1 1 4 — 8 —
312 800 *1-*8 *9-*13 *17-*24 *25-*28 50 2 1 1 4 — 8 —
313 800 *1-*8 *9-*14 *17-*24 *25-*27 50 2 1 1 4 — 8 —
314 800 *1-*8 *9-*15 *17-*24 *25,*26 50 2 1 1 4 — 8 —
315 800 *1-*8 *9-*16 *17-*24 *25 50 2 1 1 4 — 8 —
(To be continued)

INST03-07-410
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-420

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 16G 128 256
316 832 *1-*7 *9-*14 *17-*23 *25-*30 52 2 1 1 4 — 8 —
317 832 *1-*7 *9-*15 *17-*22 *25-*30 52 2 1 1 4 — 8 —
318 832 *1-*7 *9-*15 *17-*23 *25-*29 52 2 1 1 4 — 8 —
319 832 *1-*8 *9-*13 *17-*24 *25-*29 52 2 1 1 4 — 8 —
320 832 *1-*8 *9-*14 *17-*24 *25-*28 52 2 1 1 4 — 8 —
321 832 *1-*8 *9-*15 *17-*24 *25-*27 52 2 1 1 4 — 8 —
322 832 *1-*8 *9-*16 *17-*24 *25,*26 52 2 1 1 4 — 8 —
323 864 *1-*7 *9-*15 *17-*23 *25-*30 54 2 1 1 4 — 8 —
324 864 *1-*8 *9-*14 *17-*24 *25-*29 54 2 1 1 4 — 8 —
325 864 *1-*8 *9-*15 *17-*24 *25-*28 54 2 1 1 4 — 8 —
326 864 *1-*8 *9-*16 *17-*24 *25-*27 54 2 1 1 4 — 8 —
327 896 *1-*7 *9-*15 *17-*23 *25-*31 56 2 1 1 4 — 8 —
328 896 *1-*8 *9-*14 *17-*24 *25-*30 56 2 1 1 4 — 8 —
329 896 *1-*8 *9-*15 *17-*24 *25-*29 56 2 1 1 4 — 8 —
330 896 *1-*8 *9-*16 *17-*24 *25-*28 56 2 1 1 4 — 8 —
331 928 *1-*8 *9-*15 *17-*24 *25-*30 58 2 1 1 4 — 8 —
332 928 *1-*8 *9-*16 *17-*24 *25-*29 58 2 1 1 4 — 8 —
333 960 *1-*8 *9-*15 *17-*24 *25-*31 60 2 1 1 4 — 8 —
334 960 *1-*8 *9-*16 *17-*24 *25-*30 60 2 1 1 4 — 8 —
335 992 *1-*8 *9-*16 *17-*24 *25-*31 62 2 1 1 4 — 8 —
336 1024 *1-*8 *9-*16 *17-*24 *25-*32 64 2 1 1 4 — 8 —

NOTE 1: The above numbers (*17 through *32) represent the CM Module locations shown in
Fig. 3.7.1-14 or Fig. 3.7.1-18.
NOTE 2: The required SM capacity shown in Table 6.1-1 (INST06-10) must be installed in
CPEX-0.

INST03-07-420
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-430

Table 3.7.1-4 Cache memory capacity and number of necessary options 

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 32G 128 256
1 128 *1 — *17 — 4 0 1 0 2 0 4 0
2 192 *1,*2 — *17 — 6 0 1 0 2 0 4 0
3 256 *1 *9 *17 *25 8 2 1 1 4 0 8 0
4 256 *1,*2 — *17,*18 — 8 0 1 0 2 0 4 0
5 256 *1-*3 — *17 — 8 0 1 0 2 0 4 0
6 320 *1,*2 *9 *17 *25 10 2 1 1 4 0 8 0
7 320 *1-*3 — *17,*18 — 10 0 1 0 2 0 4 0
8 320 *1-*4 — *17 — 10 0 1 0 2 0 4 0
9 384 *1,*2 *9 *17,*18 *25 12 2 1 1 4 0 8 0
10 384 *1,*2 *9,*10 *17 *25 12 2 1 1 4 0 8 0
11 384 *1-*3 — *17-*19 — 12 0 1 0 2 0 4 0
12 384 *1-*3 *9 *17 *25 12 2 1 1 4 0 8 0
13 384 *1-*4 — *17,*18 — 12 0 1 0 2 0 4 0
14 384 *1-*5 — *17 — 12 0 1 0 1 1 2 2
15 448 *1,*2 *9,*10 *17,*18 *25 14 2 1 1 4 0 8 0
16 448 *1-*3 *9,*10 *17 *25 14 2 1 1 4 0 8 0
17 448 *1-*4 *9 *17 *25 14 2 1 1 4 0 8 0
18 448 *1-*5 — *17,*18 — 14 0 1 0 1 1 2 2
19 448 *1-*6 — *17 — 14 0 1 0 1 1 2 2
20 512 *1,*2 *9,*10 *17,*18 *25,*26 16 2 1 1 4 0 8 0
21 512 *1-*3 *9 *17-*19 *25 16 2 1 1 4 0 8 0
22 512 *1-*3 *9,*10 *17,*18 *25 16 2 1 1 4 0 8 0
23 512 *1-*3 *9-*11 *17 *25 16 2 1 1 4 0 8 0
24 512 *1-*4 — *17-*20 — 16 0 1 0 2 0 4 0
25 512 *1-*4 *9,*10 *17 *25 16 2 1 1 4 0 8 0
26 512 *1-*5 — *17-*19 — 16 0 1 0 1 1 2 2
27 512 *1-*5 *9 *17 *25 16 2 1 1 3 1 6 2
28 512 *1-*6 — *17,*18 — 16 0 1 0 1 1 2 2
29 512 *1-*7 — *17 — 16 0 1 0 1 1 2 2
30 576 *1-*3 *9,*10 *17,*18 *25,*26 18 2 1 1 4 0 8 0
31 576 *1-*3 *9,*10 *17-*19 *25 18 2 1 1 4 0 8 0
32 576 *1-*3 *9-*11 *17,*18 *25 18 2 1 1 4 0 8 0
33 576 *1-*4 *9,*10 *17,*18 *25 18 2 1 1 4 0 8 0
34 576 *1-*4 *9-*11 *17 *25 18 2 1 1 4 0 8 0
35 576 *1-*5 — *17-*20 — 18 0 1 0 1 1 2 2
(To be continued)

INST03-07-430
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-440

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 32G 128 256
36 576 *1-*5 *9,*10 *17 *25 18 2 1 1 3 1 6 2
37 576 *1-*6 — *17-*19 — 18 0 1 0 1 1 2 2
38 576 *1-*6 *9 *17 *25 18 2 1 1 3 1 6 2
39 576 *1-*7 — *17,*18 — 18 0 1 0 1 1 2 2
40 576 *1-*8 — *17 — 18 0 1 0 1 1 2 2
41 640 *1-*3 *9,*10 *17-*19 *25,*26 20 2 1 1 4 0 8 0
42 640 *1-*3 *9-*11 *17,*18 *25,*26 20 2 1 1 4 0 8 0
43 640 *1-*3 *9-*11 *17-*19 *25 20 2 1 1 4 0 8 0
44 640 *1-*4 *9 *17-*20 *25 20 2 1 1 4 0 8 0
45 640 *1-*4 *9,*10 *17,*18 *25,*26 20 2 1 1 4 0 8 0
46 640 *1-*4 *9-*11 *17,*18 *25 20 2 1 1 4 0 8 0
47 640 *1-*4 *9-*12 *17 *25 20 2 1 1 4 0 8 0
48 640 *1-*5 — *17-*21 — 20 0 1 0 0 2 0 4
49 640 *1-*5 *9,*10 *17,*18 *25 20 2 1 1 3 1 6 2
50 640 *1-*5 *9-*11 *17 *25 20 2 1 1 3 1 6 2
51 640 *1-*6 — *17-*20 — 20 0 1 0 1 1 2 2
52 640 *1-*6 *9,*10 *17 *25 20 2 1 1 3 1 6 2
53 640 *1-*7 — *17-*19 — 20 0 1 0 1 1 2 2
54 640 *1-*7 *9 *17 *25 20 2 1 1 3 1 6 2
55 640 *1-*8 — *17,*18 — 20 0 1 0 1 1 2 2
56 704 *1-*3 *9-*11 *17-*19 *25,*26 22 2 1 1 4 0 8 0
57 704 *1-*4 *9,*10 *17-*20 *25 22 2 1 1 4 0 8 0
58 704 *1-*4 *9-*11 *17,*18 *25,*26 22 2 1 1 4 0 8 0
59 704 *1-*4 *9-*11 *17-*19 *25 22 2 1 1 4 0 8 0
60 704 *1-*4 *9-*12 *17,*18 *25 22 2 1 1 4 0 8 0
61 704 *1-*5 *9,*10 *17,*18 *25,*26 22 2 1 1 3 1 6 2
62 704 *1-*5 *9-*11 *17,*18 *25 22 2 1 1 3 1 6 2
63 704 *1-*5 *9-*12 *17 *25 22 2 1 1 3 1 6 2
64 704 *1-*6 — *17-*21 — 22 0 1 0 0 2 0 4
65 704 *1-*6 *9,*10 *17,*18 *25 22 2 1 1 3 1 6 2
66 704 *1-*6 *9-*11 *17 *25 22 2 1 1 3 1 6 2
67 704 *1-*7 — *17-*20 — 22 0 1 0 1 1 2 2
68 704 *1-*7 *9,*10 *17 *25 22 2 1 1 3 1 6 2
69 704 *1-*8 — *17-*19 — 22 0 1 0 1 1 2 2
70 704 *1-*8 *9 *17 *25 22 2 1 1 3 1 6 2
(To be continued)

INST03-07-440
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-450

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 32G 128 256
71 768 *1-*3 *9-*11 *17-*19 *25-*27 24 2 1 1 4 0 8 0
72 768 *1-*4 *9,*10 *17-*20 *25,*26 24 2 1 1 4 0 8 0
73 768 *1-*4 *9-*11 *17-*19 *25,*26 24 2 1 1 4 0 8 0
74 768 *1-*4 *9-*11 *17-*20 *25 24 2 1 1 4 0 8 0
75 768 *1-*4 *9-*12 *17,*18 *25,*26 24 2 1 1 4 0 8 0
76 768 *1-*4 *9-*12 *17-*19 *25 24 2 1 1 4 0 8 0
77 768 *1-*5 *9 *17-*21 *25 24 2 1 1 2 2 4 4
78 768 *1-*5 *9-*11 *17,*18 *25,*26 24 2 1 1 3 1 6 2
79 768 *1-*5 *9-*11 *17-*19 *25 24 2 1 1 3 1 6 2
80 768 *1-*5 *9-*12 *17,*18 *25 24 2 1 1 3 1 6 2
81 768 *1-*5 *9-*13 *17 *25 24 2 1 1 2 2 4 4
82 768 *1-*6 — *17-*22 — 24 0 1 0 0 2 0 4
83 768 *1-*6 *9,*10 *17,*18 *25,*26 24 2 1 1 3 1 6 2
84 768 *1-*6 *9-*11 *17,*18 *25 24 2 1 1 3 1 6 2
85 768 *1-*6 *9-*12 *17 *25 24 2 1 1 3 1 6 2
86 768 *1-*7 — *17-*21 — 24 0 1 0 0 2 0 4
87 768 *1-*7 *9,*10 *17,*18 *25 24 2 1 1 3 1 6 2
88 768 *1-*7 *9-*11 *17 *25 24 2 1 1 3 1 6 2
89 768 *1-*8 — *17-*20 — 24 0 1 0 1 1 2 2
90 768 *1-*8 *9,*10 *17 *25 24 2 1 1 3 1 6 2
91 832 *1-*4 *9-*11 *17-*19 *25-*27 26 2 1 1 4 0 8 0
92 832 *1-*4 *9-*11 *17-*20 *25,*26 26 2 1 1 4 0 8 0
93 832 *1-*4 *9-*12 *17-*19 *25,*26 26 2 1 1 4 0 8 0
94 832 *1-*4 *9-*12 *17-*20 *25 26 2 1 1 4 0 8 0
95 832 *1-*5 *9,*10 *17-*21 *25 26 2 1 1 2 2 4 4
96 832 *1-*5 *9-*11 *17-*19 *25,*26 26 2 1 1 3 1 6 2
97 832 *1-*5 *9-*12 *17,*18 *25,*26 26 2 1 1 3 1 6 2
98 832 *1-*5 *9-*12 *17-*19 *25 26 2 1 1 3 1 6 2
99 832 *1-*5 *9-*13 *17,*18 *25 26 2 1 1 2 2 4 4
100 832 *1-*6 *9-*11 *17,*18 *25,*26 26 2 1 1 3 1 6 2
101 832 *1-*6 *9-*11 *17-*19 *25 26 2 1 1 3 1 6 2
102 832 *1-*6 *9-*12 *17,*18 *25 26 2 1 1 3 1 6 2
103 832 *1-*6 *9-*13 *17 *25 26 2 1 1 2 2 4 4
104 832 *1-*7 — *17-*22 — 26 0 1 0 0 2 0 4
105 832 *1-*7 *9,*10 *17,*18 *25,*26 26 2 1 1 3 1 6 2
(To be continued)

INST03-07-450
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-460

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 32G 128 256
106 832 *1-*7 *9-*11 *17,*18 *25 26 2 1 1 3 1 6 2
107 832 *1-*7 *9-*12 *17 *25 26 2 1 1 3 1 6 2
108 832 *1-*8 — *17-*21 — 26 0 1 0 0 2 0 4
109 832 *1-*8 *9-*11 *17 *25 26 2 1 1 3 1 6 2
110 896 *1-*4 *9-*11 *17-*20 *25-*27 28 2 1 1 4 0 8 0
111 896 *1-*4 *9-*12 *17-*19 *25-*27 28 2 1 1 4 0 8 0
112 896 *1-*4 *9-*12 *17-*20 *25,*26 28 2 1 1 4 0 8 0
113 896 *1-*5 *9,*10 *17-*21 *25,*26 28 2 1 1 2 2 4 4
114 896 *1-*5 *9-*11 *17-*19 *25-*27 28 2 1 1 3 1 6 2
115 896 *1-*5 *9-*11 *17-*21 *25 28 2 1 1 2 2 4 4
116 896 *1-*5 *9-*12 *17-*19 *25,*26 28 2 1 1 3 1 6 2
117 896 *1-*5 *9-*12 *17-*20 *25 28 2 1 1 3 1 6 2
118 896 *1-*5 *9-*13 *17,*18 *25,*26 28 2 1 1 2 2 4 4
119 896 *1-*5 *9-*13 *17-*19 *25 28 2 1 1 2 2 4 4
120 896 *1-*6 *9 *17-*22 *25 28 2 1 1 2 2 4 4
121 896 *1-*6 *9-*11 *17-*19 *25,*26 28 2 1 1 3 1 6 2
122 896 *1-*6 *9-*12 *17,*18 *25,*26 28 2 1 1 3 1 6 2
123 896 *1-*6 *9-*12 *17-*19 *25 28 2 1 1 3 1 6 2
124 896 *1-*6 *9-*13 *17,*18 *25 28 2 1 1 2 2 4 4
125 896 *1-*6 *9-*14 *17 *25 28 2 1 1 2 2 4 4
126 896 *1-*7 — *17-*23 — 28 0 1 0 0 2 0 4
127 896 *1-*7 *9-*11 *17,*18 *25,*26 28 2 1 1 3 1 6 2
128 896 *1-*7 *9-*11 *17-*19 *25 28 2 1 1 3 1 6 2
129 896 *1-*7 *9-*12 *17,*18 *25 28 2 1 1 3 1 6 2
130 896 *1-*7 *9-*13 *17 *25 28 2 1 1 2 2 4 4
131 896 *1-*8 — *17-*22 — 28 0 1 0 0 2 0 4
132 896 *1-*8 *9-*12 *17 *25 28 2 1 1 3 1 6 2
133 960 *1-*4 *9-*12 *17-*20 *25-*27 30 2 1 1 4 0 8 0
134 960 *1-*5 *9-*11 *17-*21 *25,*26 30 2 1 1 2 2 4 4
135 960 *1-*5 *9-*12 *17-*19 *25-*27 30 2 1 1 3 1 6 2
136 960 *1-*5 *9-*12 *17-*20 *25,*26 30 2 1 1 3 1 6 2
137 960 *1-*5 *9-*12 *17-*21 *25 30 2 1 1 2 2 4 4
138 960 *1-*5 *9-*13 *17-*19 *25,*26 30 2 1 1 2 2 4 4
139 960 *1-*5 *9-*13 *17-*20 *25 30 2 1 1 2 2 4 4
140 960 *1-*6 *9,*10 *17-*22 *25 30 2 1 1 2 2 4 4
(To be continued)

INST03-07-460
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-470

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 32G 128 256
141 960 *1-*6 *9-*11 *17-*19 *25-*27 30 2 1 1 3 1 6 2
142 960 *1-*6 *9-*12 *17-*19 *25,*26 30 2 1 1 3 1 6 2
143 960 *1-*6 *9-*12 *17-*20 *25 30 2 1 1 3 1 6 2
144 960 *1-*6 *9-*13 *17,*18 *25,*26 30 2 1 1 2 2 4 4
145 960 *1-*6 *9-*13 *17-*19 *25 30 2 1 1 2 2 4 4
146 960 *1-*6 *9-*14 *17,*18 *25 30 2 1 1 2 2 4 4
147 960 *1-*7 *9-*11 *17-*19 *25,*26 30 2 1 1 3 1 6 2
148 960 *1-*7 *9-*12 *17,*18 *25,*26 30 2 1 1 3 1 6 2
149 960 *1-*7 *9-*12 *17-*19 *25 30 2 1 1 3 1 6 2
150 960 *1-*7 *9-*13 *17,*18 *25 30 2 1 1 2 2 4 4
151 960 *1-*8 — *17-*23 — 30 0 1 0 0 2 0 4
152 960 *1-*8 *9-*13 *17 *25 30 2 1 1 2 2 4 4
153 1024 *1-*4 *9-*12 *17-*20 *25-*28 32 2 1 1 4 0 8 0
154 1024 *1-*5 *9-*11 *17-*21 *25-*27 32 2 1 1 2 2 4 4
155 1024 *1-*5 *9-*12 *17-*20 *25-*27 32 2 1 1 3 1 6 2
156 1024 *1-*5 *9-*12 *17-*21 *25,*26 32 2 1 1 2 2 4 4
157 1024 *1-*5 *9-*13 *17-*19 *25-*27 32 2 1 1 2 2 4 4
158 1024 *1-*5 *9-*13 *17-*20 *25,*26 32 2 1 1 2 2 4 4
159 1024 *1-*5 *9-*13 *17-*21 *25 32 2 1 1 1 3 2 6
160 1024 *1-*6 *9,*10 *17-*22 *25,*26 32 2 1 1 2 2 4 4
161 1024 *1-*6 *9-*11 *17-*22 *25 32 2 1 1 2 2 4 4
162 1024 *1-*6 *9-*12 *17-*19 *25-*27 32 2 1 1 3 1 6 2
163 1024 *1-*6 *9-*12 *17-*20 *25,*26 32 2 1 1 3 1 6 2
164 1024 *1-*6 *9-*13 *17-*19 *25,*26 32 2 1 1 2 2 4 4
165 1024 *1-*6 *9-*13 *17-*20 *25 32 2 1 1 2 2 4 4
166 1024 *1-*6 *9-*14 *17,*18 *25,*26 32 2 1 1 2 2 4 4
167 1024 *1-*6 *9-*14 *17-*19 *25 32 2 1 1 2 2 4 4
168 1024 *1-*7 *9 *17-*23 *25 32 2 1 1 2 2 4 4
169 1024 *1-*7 *9-*11 *17-*19 *25-*27 32 2 1 1 3 1 6 2
170 1024 *1-*7 *9-*12 *17-*19 *25,*26 32 2 1 1 3 1 6 2
171 1024 *1-*7 *9-*12 *17-*20 *25 32 2 1 1 3 1 6 2
172 1024 *1-*7 *9-*13 *17,*18 *25,*26 32 2 1 1 2 2 4 4
173 1024 *1-*7 *9-*13 *17-*19 *25 32 2 1 1 2 2 4 4
174 1024 *1-*7 *9-*15 *17 *25 32 2 1 1 2 2 4 4
175 1024 *1-*8 — *17-*24 — 32 0 1 0 0 2 0 4
(To be continued)

INST03-07-470
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-480

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 32G 128 256
176 1024 *1-*8 *9-*14 *17 *25 32 2 1 1 2 2 4 4
177 1088 *1-*5 *9-*12 *17-*20 *25-*28 34 2 1 1 3 1 6 2
178 1088 *1-*5 *9-*12 *17-*21 *25-*27 34 2 1 1 2 2 4 4
179 1088 *1-*5 *9-*13 *17-*20 *25-*27 34 2 1 1 2 2 4 4
180 1088 *1-*5 *9-*13 *17-*21 *25,*26 34 2 1 1 1 3 2 6
181 1088 *1-*6 *9-*11 *17-*22 *25,*26 34 2 1 1 2 2 4 4
182 1088 *1-*6 *9-*12 *17-*20 *25-*27 34 2 1 1 3 1 6 2
183 1088 *1-*6 *9-*12 *17-*22 *25 34 2 1 1 2 2 4 4
184 1088 *1-*6 *9-*13 *17-*19 *25-*27 34 2 1 1 2 2 4 4
185 1088 *1-*6 *9-*13 *17-*20 *25,*26 34 2 1 1 2 2 4 4
186 1088 *1-*6 *9-*13 *17-*21 *25 34 2 1 1 1 3 2 6
187 1088 *1-*6 *9-*14 *17-*19 *25,*26 34 2 1 1 2 2 4 4
188 1088 *1-*6 *9-*14 *17-*20 *25 34 2 1 1 2 2 4 4
189 1088 *1-*7 *9,*10 *17-*23 *25 34 2 1 1 2 2 4 4
190 1088 *1-*7 *9-*12 *17-*19 *25-*27 34 2 1 1 3 1 6 2
191 1088 *1-*7 *9-*12 *17-*20 *25,*26 34 2 1 1 3 1 6 2
192 1088 *1-*7 *9-*13 *17-*19 *25,*26 34 2 1 1 2 2 4 4
193 1088 *1-*7 *9-*13 *17-*20 *25 34 2 1 1 2 2 4 4
194 1088 *1-*7 *9-*15 *17,*18 *25 34 2 1 1 2 2 4 4
195 1088 *1-*8 *9-*15 *17 *25 34 2 1 1 2 2 4 4
196 1152 *1-*5 *9-*12 *17-*21 *25-*28 36 2 1 1 2 2 4 4
197 1152 *1-*5 *9-*13 *17-*20 *25-*28 36 2 1 1 2 2 4 4
198 1152 *1-*5 *9-*13 *17-*21 *25-*27 36 2 1 1 1 3 2 6
199 1152 *1-*6 *9-*11 *17-*22 *25-*27 36 2 1 1 2 2 4 4
200 1152 *1-*6 *9-*12 *17-*20 *25-*28 36 2 1 1 3 1 6 2
201 1152 *1-*6 *9-*12 *17-*22 *25,*26 36 2 1 1 2 2 4 4
202 1152 *1-*6 *9-*13 *17-*20 *25-*27 36 2 1 1 2 2 4 4
203 1152 *1-*6 *9-*13 *17-*21 *25,*26 36 2 1 1 1 3 2 6
204 1152 *1-*6 *9-*13 *17-*22 *25 36 2 1 1 1 3 2 6
205 1152 *1-*6 *9-*13 *17-*22 *25 36 2 1 1 1 3 2 6
206 1152 *1-*6 *9-*14 *17-*19 *25-*27 36 2 1 1 2 2 4 4
207 1152 *1-*6 *9-*14 *17-*20 *25,*26 36 2 1 1 2 2 4 4
208 1152 *1-*6 *9-*14 *17-*21 *25 36 2 1 1 1 3 2 6
209 1152 *1-*7 *9,*10 *17-*23 *25,*26 36 2 1 1 2 2 4 4
210 1152 *1-*7 *9-*11 *17-*23 *25 36 2 1 1 2 2 4 4
(To be continued)

INST03-07-480
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-490

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 32G 128 256
211 1152 *1-*7 *9-*12 *17-*20 *25-*27 36 2 1 1 3 1 6 2
212 1152 *1-*7 *9-*13 *17-*19 *25-*27 36 2 1 1 2 2 4 4
213 1152 *1-*7 *9-*13 *17-*20 *25,*26 36 2 1 1 2 2 4 4
214 1152 *1-*7 *9-*13 *17-*21 *25 36 2 1 1 1 3 2 6
215 1152 *1-*7 *9-*15 *17-*19 *25 36 2 1 1 2 2 4 4
216 1152 *1-*8 *9 *17-*24 *25 36 2 1 1 2 2 4 4
217 1152 *1-*8 *9-*16 *17 *25 36 2 1 1 2 2 4 4
218 1216 *1-*5 *9-*13 *17-*21 *25-*28 38 2 1 1 1 3 2 6
219 1216 *1-*6 *9-*12 *17-*22 *25-*27 38 2 1 1 2 2 4 4
220 1216 *1-*6 *9-*13 *17-*20 *25-*28 38 2 1 1 2 2 4 4
221 1216 *1-*6 *9-*13 *17-*21 *25-*27 38 2 1 1 1 3 2 6
222 1216 *1-*6 *9-*13 *17-*22 *25,*26 38 2 1 1 1 3 2 6
223 1216 *1-*6 *9-*14 *17-*20 *25-*27 38 2 1 1 2 2 4 4
224 1216 *1-*6 *9-*14 *17-*21 *25,*26 38 2 1 1 1 3 2 6
225 1216 *1-*6 *9-*14 *17-*22 *25 38 2 1 1 1 3 2 6
226 1216 *1-*7 *9-*11 *17-*23 *25,*26 38 2 1 1 2 2 4 4
227 1216 *1-*7 *9-*12 *17-*20 *25-*28 38 2 1 1 3 1 6 2
228 1216 *1-*7 *9-*12 *17-*23 *25 38 2 1 1 2 2 4 4
229 1216 *1-*7 *9-*13 *17-*20 *25-*27 38 2 1 1 2 2 4 4
230 1216 *1-*7 *9-*13 *17-*21 *25,*26 38 2 1 1 1 3 2 6
231 1216 *1-*7 *9-*15 *17-*19 *25,*26 38 2 1 1 2 2 4 4
232 1216 *1-*7 *9-*15 *17-*20 *25 38 2 1 1 2 2 4 4
233 1216 *1-*8 *9,*10 *17-*24 *25 38 2 1 1 2 2 4 4
234 1216 *1-*8 *9-*16 *17,*18 *25 38 2 1 1 2 2 4 4
235 1280 *1-*5 *9-*13 *17-*21 *25-*29 40 2 1 1 0 4 0 8
236 1280 *1-*6 *9-*12 *17-*22 *25-*28 40 2 1 1 2 2 4 4
237 1280 *1-*6 *9-*13 *17-*21 *25-*28 40 2 1 1 1 3 2 6
238 1280 *1-*6 *9-*13 *17-*22 *25-*27 40 2 1 1 1 3 2 6
239 1280 *1-*6 *9-*14 *17-*20 *25-*28 40 2 1 1 2 2 4 4
240 1280 *1-*6 *9-*14 *17-*21 *25-*27 40 2 1 1 1 3 2 6
241 1280 *1-*6 *9-*14 *17-*22 *25,*26 40 2 1 1 1 3 2 6
242 1280 *1-*7 *9-*11 *17-*23 *25-*27 40 2 1 1 2 2 4 4
243 1280 *1-*7 *9-*12 *17-*23 *25,*26 40 2 1 1 2 2 4 4
244 1280 *1-*7 *9-*13 *17-*20 *25-*28 40 2 1 1 2 2 4 4
245 1280 *1-*7 *9-*13 *17-*21 *25-*27 40 2 1 1 1 3 2 6
(To be continued)

INST03-07-490
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-500

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 32G 128 256
246 1280 *1-*7 *9-*13 *17-*23 *25 40 2 1 1 1 3 2 6
247 1280 *1-*7 *9-*14 *17-*22 *25 40 2 1 1 1 3 2 6
248 1280 *1-*7 *9-*15 *17-*19 *25-*27 40 2 1 1 2 2 4 4
249 1280 *1-*7 *9-*15 *17-*20 *25,*26 40 2 1 1 2 2 4 4
250 1280 *1-*7 *9-*15 *17-*21 *25 40 2 1 1 1 3 2 6
251 1280 *1-*8 *9,*10 *17-*24 *25,*26 40 2 1 1 2 2 4 4
252 1280 *1-*8 *9-*11 *17-*24 *25 40 2 1 1 2 2 4 4
253 1280 *1-*8 *9-*16 *17-*19 *25 40 2 1 1 2 2 4 4
254 1344 *1-*6 *9-*13 *17-*21 *25-*29 42 2 1 1 0 4 0 8
255 1344 *1-*6 *9-*13 *17-*22 *25-*28 42 2 1 1 1 3 2 6
256 1344 *1-*6 *9-*14 *17-*21 *25-*28 42 2 1 1 1 3 2 6
257 1344 *1-*6 *9-*14 *17-*22 *25-*27 42 2 1 1 1 3 2 6
258 1344 *1-*7 *9-*12 *17-*23 *25-*27 42 2 1 1 2 2 4 4
259 1344 *1-*7 *9-*13 *17-*21 *25-*28 42 2 1 1 1 3 2 6
260 1344 *1-*7 *9-*13 *17-*23 *25,*26 42 2 1 1 1 3 2 6
261 1344 *1-*7 *9-*14 *17-*22 *25,*26 42 2 1 1 1 3 2 6
262 1344 *1-*7 *9-*14 *17-*23 *25 42 2 1 1 1 3 2 6
263 1344 *1-*7 *9-*15 *17-*20 *25-*27 42 2 1 1 2 2 4 4
264 1344 *1-*7 *9-*15 *17-*21 *25,*26 42 2 1 1 1 3 2 6
265 1344 *1-*7 *9-*15 *17-*22 *25 42 2 1 1 1 3 2 6
266 1344 *1-*8 *9-*11 *17-*24 *25,*26 42 2 1 1 2 2 4 4
267 1344 *1-*8 *9-*12 *17-*24 *25 42 2 1 1 2 2 4 4
268 1344 *1-*8 *9-*16 *17-*20 *25 42 2 1 1 2 2 4 4
269 1408 *1-*6 *9-*13 *17-*22 *25-*29 44 2 1 1 0 4 0 8
270 1408 *1-*6 *9-*14 *17-*21 *25-*29 44 2 1 1 0 4 0 8
271 1408 *1-*6 *9-*14 *17-*22 *25-*28 44 2 1 1 1 3 2 6
272 1408 *1-*7 *9-*12 *17-*23 *25-*28 44 2 1 1 2 2 4 4
273 1408 *1-*7 *9-*13 *17-*21 *25-*29 44 2 1 1 0 4 0 8
274 1408 *1-*7 *9-*13 *17-*23 *25-*27 44 2 1 1 1 3 2 6
275 1408 *1-*7 *9-*14 *17-*22 *25-*27 44 2 1 1 1 3 2 6
276 1408 *1-*7 *9-*14 *17-*23 *25,*26 44 2 1 1 1 3 2 6
277 1408 *1-*7 *9-*15 *17-*20 *25-*28 44 2 1 1 2 2 4 4
278 1408 *1-*7 *9-*15 *17-*21 *25-*27 44 2 1 1 1 3 2 6
279 1408 *1-*7 *9-*15 *17-*22 *25,*26 44 2 1 1 1 3 2 6
280 1408 *1-*7 *9-*15 *17-*23 *25 44 2 1 1 1 3 2 6
(To be continued)

INST03-07-500
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-510

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 32G 128 256
281 1408 *1-*8 *9-*11 *17-*24 *25-*27 44 2 1 1 2 2 4 4
282 1408 *1-*8 *9-*12 *17-*24 *25,*26 44 2 1 1 2 2 4 4
283 1408 *1-*8 *9-*13 *17-*24 *25 44 2 1 1 1 3 2 6
284 1408 *1-*8 *9-*16 *17-*21 *25 44 2 1 1 1 3 2 6
285 1472 *1-*6 *9-*14 *17-*22 *25-*29 46 2 1 1 0 4 0 8
286 1472 *1-*7 *9-*13 *17-*23 *25-*28 46 2 1 1 1 3 2 6
287 1472 *1-*7 *9-*14 *17-*22 *25-*28 46 2 1 1 1 3 2 6
288 1472 *1-*7 *9-*14 *17-*23 *25-*27 46 2 1 1 1 3 2 6
289 1472 *1-*7 *9-*15 *17-*21 *25-*28 46 2 1 1 1 3 2 6
290 1472 *1-*7 *9-*15 *17-*22 *25-*27 46 2 1 1 1 3 2 6
291 1472 *1-*7 *9-*15 *17-*23 *25,*26 46 2 1 1 1 3 2 6
292 1472 *1-*8 *9-*12 *17-*24 *25-*27 46 2 1 1 2 2 4 4
293 1472 *1-*8 *9-*13 *17-*24 *25,*26 46 2 1 1 1 3 2 6
294 1472 *1-*8 *9-*14 *17-*24 *25 46 2 1 1 1 3 2 6
295 1472 *1-*8 *9-*16 *17-*22 *25 46 2 1 1 1 3 2 6
296 1536 *1-*6 *9-*14 *17-*22 *25-*30 48 2 1 1 0 4 0 8
297 1536 *1-*7 *9-*13 *17-*23 *25-*29 48 2 1 1 0 4 0 8
298 1536 *1-*7 *9-*14 *17-*22 *25-*29 48 2 1 1 0 4 0 8
299 1536 *1-*7 *9-*14 *17-*23 *25-*28 48 2 1 1 1 3 2 6
300 1536 *1-*7 *9-*15 *17-*21 *25-*29 48 2 1 1 0 4 0 8
301 1536 *1-*7 *9-*15 *17-*22 *25-*28 48 2 1 1 1 3 2 6
302 1536 *1-*7 *9-*15 *17-*23 *25-*27 48 2 1 1 1 3 2 6
303 1536 *1-*8 *9-*12 *17-*24 *25-*28 48 2 1 1 2 2 4 4
304 1536 *1-*8 *9-*13 *17-*24 *25-*27 48 2 1 1 1 3 2 6
305 1536 *1-*8 *9-*14 *17-*24 *25,*26 48 2 1 1 1 3 2 6
306 1536 *1-*8 *9-*15 *17-*24 *25 48 2 1 1 1 3 2 6
307 1536 *1-*8 *9-*16 *17-*23 *25 48 2 1 1 1 3 2 6
308 1600 *1-*7 *9-*14 *17-*22 *25-*30 50 2 1 1 0 4 0 8
309 1600 *1-*7 *9-*14 *17-*23 *25-*29 50 2 1 1 0 4 0 8
310 1600 *1-*7 *9-*15 *17-*22 *25-*29 50 2 1 1 0 4 0 8
311 1600 *1-*7 *9-*15 *17-*23 *25-*28 50 2 1 1 1 3 2 6
312 1600 *1-*8 *9-*13 *17-*24 *25-*28 50 2 1 1 1 3 2 6
313 1600 *1-*8 *9-*14 *17-*24 *25-*27 50 2 1 1 1 3 2 6
314 1600 *1-*8 *9-*15 *17-*24 *25,*26 50 2 1 1 1 3 2 6
315 1600 *1-*8 *9-*16 *17-*24 *25 50 2 1 1 1 3 2 6
(To be continued)

INST03-07-510
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-520

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 32G 128 256
316 1664 *1-*7 *9-*14 *17-*23 *25-*30 52 2 1 1 0 4 0 8
317 1664 *1-*7 *9-*15 *17-*22 *25-*30 52 2 1 1 0 4 0 8
318 1664 *1-*7 *9-*15 *17-*23 *25-*29 52 2 1 1 0 4 0 8
319 1664 *1-*8 *9-*13 *17-*24 *25-*29 52 2 1 1 0 4 0 8
320 1664 *1-*8 *9-*14 *17-*24 *25-*28 52 2 1 1 1 3 2 6
321 1664 *1-*8 *9-*15 *17-*24 *25-*27 52 2 1 1 1 3 2 6
322 1664 *1-*8 *9-*16 *17-*24 *25,*26 52 2 1 1 1 3 2 6
323 1728 *1-*7 *9-*15 *17-*23 *25-*30 54 2 1 1 0 4 0 8
324 1728 *1-*8 *9-*14 *17-*24 *25-*29 54 2 1 1 0 4 0 8
325 1728 *1-*8 *9-*15 *17-*24 *25-*28 54 2 1 1 1 3 2 6
326 1728 *1-*8 *9-*16 *17-*24 *25-*27 54 2 1 1 1 3 2 6
327 1792 *1-*7 *9-*15 *17-*23 *25-*31 56 2 1 1 0 4 0 8
328 1792 *1-*8 *9-*14 *17-*24 *25-*30 56 2 1 1 0 4 0 8
329 1792 *1-*8 *9-*15 *17-*24 *25-*29 56 2 1 1 0 4 0 8
330 1792 *1-*8 *9-*16 *17-*24 *25-*28 56 2 1 1 1 3 2 6
331 1856 *1-*8 *9-*15 *17-*24 *25-*30 58 2 1 1 0 4 0 8
332 1856 *1-*8 *9-*16 *17-*24 *25-*29 58 2 1 1 0 4 0 8
333 1920 *1-*8 *9-*15 *17-*24 *25-*31 60 2 1 1 0 4 0 8
334 1920 *1-*8 *9-*16 *17-*24 *25-*30 60 2 1 1 0 4 0 8
335 1984 *1-*8 *9-*16 *17-*24 *25-*31 62 2 1 1 0 4 0 8
336 2048 *1-*8 *9-*16 *17-*24 *25-*32 64 2 1 1 0 4 0 8

NOTE 1: The above numbers (*17 through *32) represent the CM Module locations shown in
Fig. 3.7.1-14 or Fig. 3.7.1-18.
NOTE 2: The required SM capacity shown in Table 6.1-1 (INST06-10) must be installed in
CPEX-0.

INST03-07-520
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-530

6-2 Insert the PCB.

a. Remove the two screws and remove the dummy plate.
NOTE: Store the removed dummy plate as it is required when the Additional Cache Path
Control Adapter is removed.

NOTICE: Remove the dummy plate just before installing the PCB.
If the dummy plate is kept removed for a long time, the wind doesn’t flow
among installed PCBs, causing the PCBs’ temperature rise which may result
in temperature warning or temperature alarm.

b. Install the CM PCB and tighten the two screws.

NOTE: When inserting the CM PCB, be careful not to get cables caught on anything.

Main Edge Connector

PCB NOTICE: • Check that the main edge connector of the PCB has
no deformation, damage or sticking of dust before
installing the PCB. (See INST03-01-80)
• When installing the PCB, hold the top and bottom of
the PCB with both hands, and insert it straight not to
contact the neighboring PCB.

Table 3.7.1-5 Location of the CM PCB

Cluster Box Slot No. Location No. Remarks
1 DKC-1 1CC CACHE-1CC
1CD CACHE-1CD

INST03-07-530
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-540

2 2 1 1
C C C C
D C C D

DKC

Front View DKC-1

CM PCB

Screw
Lever

Screw
Lever Screw

Dummy Plate

Fig. 3.7.1-16 Installation of PCB

INST03-07-540
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-550

7. SVP Post-Procedure
(1)
After completing the additional
installation of the cache memory, select
(CL) [OK] in response to “Replace or
insert the Cache Memory
PCB(s)(Memory)of cluster-1. When
completed, please press OK.”.

(2) <Cache CUDG executes>

“INLINE CUDG is now running...” is displayed.

(3)
“Changing the configuration date, for equipment of shared/cache memory...”
“Restoring the Cache Memory PCB...” is displayed.

NOTICE: Recover according to the procedure shown in “TROUBLE SHOOTING

SECTION” (Refer to TRBL02-470) when the mistake of the memory module
setting occurs.

INST03-07-550
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-560

8. SVP pre procedure (Cache Memory ) (Cluster 2)

(1) <Perform cache hardware installation>
At this point refrain from pressing the
[OK] button.
When “Replace or insert the Cache
Memory PCB(s)(Memory) of cluster-2.
When completed, please press [OK].” is
displayed, install hardware components
according to the cache hardware
installation procedure.

Make sure of the installation location and

size of the module to be added and insert
the correct module in the correct location.
(The Shared Memory capacity may be
changed at the same time, depending on the set Cache Memory capacity.)

INST03-07-560
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-570

9. Install the Cache Memory on the cluster 2

NOTICE: Be sure to wear your wrist strap and attach to ground prior to performing the
following work. This will ensure that the IC and LSI on the PCB are protected
from static electricity.

9-1 Insert the CM Modules.

a. Loosen the screw and remove the cover.

Screw

CM PCB

Cover

Fig. 3.7.1-17 Removal of Cover

INST03-07-570
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-580

b. Remove the dust covers that match the required Cache Memory capacity referring to Fig.
3.7.1-18, Fig. 3.7.1-19, Table 3.7.1-1 through Table 3.7.1-4.
c. Insert the CM Modules that match the required Cache Memory capacity.
d. Attach the cover and tighten the screw. (Refer to Fig. 3.7.1-17.)

CM Module Location of DKC-1

Cluster 2 (CACHE-2CC/2CD)

Removal of Dust Cover

A CM PCB Dust Cover

(WP840-A) Socket
PCB
Viewed from A

CACHE-2CC (Option 2) CACHE-2CD (Option 3)

CM1P: *18 CM1P: *26

CM5P: *22 CM5P: *30
CM3P: *20 CM3P: *28
CM7P: *24 CM7P: *32

CM6P: *23 CM6P: *31

CM2P: *19 CM2P: *27
CM4P: *21 CM4P: *29
CM0P: *17 CM0P: *25

NOTE: The cache memory module location *17 through *32 correspond to the CM
Location listed in Table 3.7.1-1 through Table 3.7.1-4.
Fig. 3.7.1-18 Inserting Location of the CM Module

INST03-07-580
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-590


Memory Module 
 Lever
Cut

Socket

Projection
inside the slot

Installation
 Position the cut of the memory module with the projection inside the slot, and place the memory module
on the socket.
 Hold both ends of the memory module by the fingers, and fit it into the socket.
 Make sure that the lever is firmly fitted in the memory module.

NOTICE: Do not put intense pressure on the CM Module to the extent that the PCB
greatly bends after the CM Module is secured with the levers in installation
procedure of the CM Module. The PCB may be damaged when intense
pressure is applied.

Memory Module Appearance

There are two types of memory modules. One has a heat spreader and the other has no heat spreaders.
Both memory modules can be used because they are compatible with each other.

Memory Module Memory Module

(with Heat Spreader) (without Heat Spreader)

Heat Spreader

Fig. 3.7.1-19 Insertion of Memory Module

INST03-07-590
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-600

9-2 Insert the PCB.

a. Remove the two screws and remove the dummy plate.
NOTE: Store the removed dummy plate as it is required when the Additional Cache Path
Control Adapter is removed.

NOTICE: Remove the dummy plate just before installing the PCB.
If the dummy plate is kept removed for a long time, the wind doesn’t flow
among installed PCBs, causing the PCBs’ temperature rise which may result
in temperature warning or temperature alarm.

b. Install the CM PCB and tighten the two screws.

NOTE: When inserting the CM PCB, be careful not to get cables caught on anything.

Main Edge Connector

PCB NOTICE: • Check that the main edge connector of the PCB has
no deformation, damage or sticking of dust before
installing the PCB. (See INST03-01-80)
• When installing the PCB, hold the top and bottom of
the PCB with both hands, and insert it straight not to
contact the neighboring PCB.

Table 3.7.1-6 Location of the CM PCB

Cluster Box Slot No. Location No. Remarks
2 DKC-1 2CC CACHE-2CC
2CD CACHE-2CD

INST03-07-600
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-610

2 2 1 1
C C C C
D C C D

DKC

Front View DKC-1

CM PCB

Screw
Lever

Screw
Lever Screw

Dummy Plate

Fig. 3.7.1-20 Installation of PCB

INST03-07-610
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-620

10. SVP Post-Procedure

(1)
After completing the additional
installation of the cache memory, select
(CL) [OK] in response to “Replace or
insert the Cache Memory
PCB(s)(Memory)of cluster-2. When
completed, please press [OK].”.

(2) <Cache CUDG executes>

“INLINE CUDG is now running...” is displayed.

(3)
“Changing the configuration date, for equipment of shared/cache memory...”
“Restoring the Cache Memory PCB...” is displayed.

NOTICE: Recover according to the procedure shown in “TROUBLE SHOOTING

SECTION” (Refer to TRBL02-470) when the mistake of the memory module
setting occurs.

INST03-07-620
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-630

11. SVP pre procedure (Check Power ON)

(1) <Downloading the microprogram>
The microprogram is downloaded to the SM.
The progress of the downloading is displayed.

(2) <Power ON>

“- Connect the LAN cable.
- Insert MODCON-0 and MODCON-1,
and then connect the MODCON cable.
- Connect the MFC cable.
- Connect the cable to the power supplies
(DKCPS-10 DKCPS-11 DKCPS-12
DKCPS-13).
After all the above operations are done,
turn the breaker ON and click [OK].” is
displayed.

NOTE: Do not select (CL) [OK] by mistake before installing the part(s) to be added in the
storage system.

INST03-07-630
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-640

12. Installation Procedure of Inter-Controller Connecting Kit (DKC-F810I-MOD5/MOD30/

MOD1J)
12-1 Installation of LAN Cable
a. Route the LAN cable on the rear side of the rack. After adjusting the cable routing, roll up
the extra length of the cable and put it in the space between the bottom of the rack and the
floor.
b. Connect the LAN cable (P83) to the connector (J83) on the HUBBOX-10 on the rear
side of the DKC-1.
c. Connect the LAN cable (P84) to the connector (J84) on the SVP-BASIC on the rear
side of the DKC-0.

HUBBOX-10

DKC-1

P83
SVP-BASIC

DKC-0

Extra Length
Adjustment

LAN Cable
Rear View of
RACK
P84

Fig. 3.7.1-21 Installation of LAN Cable (DKC-0 ↔ DKC-1)

INST03-07-640
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-650

12-2 Installation of MODCON

a. Insert the MODCON to the rear of the DKC-0 and fix it with the screw.
b. Insert the MODCON to the rear of the DKC-1 and fix it with the screw.

MOD MOD
CON CON
-0 -1

Rear View of DKC-0 Rear View of DKC-1

DKC

MODCON

Screw

Fig. 3.7.1-22 Installation of MODCON

INST03-07-650
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-660

12-3 Installation of MODCON Cable

a. Attach the four included Location Labels to the MODCON Cable (two cables).

Location Label  Location Label 

MODCON Cable

Fig. 3.7.1-23 Attachment of Location Labels

Table 3.7.1-7 Location Label List

No. Connection Source (DKC-0) Connection Destination (DKC-1) Remarks
Part Name Location Label  Part Name Location Label 
1 MODCON-0 MOD-01 MODCON-1 MOD-11
2 MODCON-0 MOD-02 MODCON-1 MOD-12

INST03-07-660
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-670

b. Route the MODCON cables on the rear side of the rack.

c. Remove the caps from the MODCON cables and connect the MODCON cables to the
MODCON-0 and the MODCON-1.
DKC-1
MODCON-1

MODCON-0 MOD-11

DKC-0 MOD-12

MOD-01

MOD-02

Extra Length
Adjustment

Rear View of
RACK
MODCON Cable
MODCON Cable

Cap

Fig. 3.7.1-24 Installation of MODCON Cable

INST03-07-670
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-680

12-4 Removal of Cable Covers and Accessory Box (If they are already removed, this procedure is
not necessary)
a. Loosen the three screws  on the front side of the DKC-0 and remove the cable cover.
b. Loosen the screw  and remove the accessory box.

Front View of DKC-x

DKC-x

Accessory Box

Screw 
Front View Screw 

Screw 

Cable Cover

Fig. 3.7.1-25 Removal of Cable Cover and Accessory Box

INST03-07-680
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-690

c. Loosen the three screws on the rear side of the DKC-0 and remove the cable cover.
d. In the same manner, remove the two cable covers and the accessory box from the DKC-1.

Rear View of DKC-x

DKC-x

Cable Cover

Screw

Rear View

Screw

Fig. 3.7.1-26 Removal of Cable Cover

INST03-07-690
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-700

12-5 Installation of MFC Cable

a. Attach 16 location labels to 8 MFC cables. Choose location labels from Labels (Address)
3.
b. Stick the Label (Protect) around the attached location labels.

Location Label  Location Label 

MFC Cable

[Label Attachment Example]

MFC Cable

Location Label

Edge

Label (Protect)

 Attach the location label to the MFC cable.

 Attach the Label (Protect) to the location label with its edge aligned with the location label.
 Stick the Label (Protect) around the location label so that the location label is not torn off.

Fig. 3.7.1-27 Attachment of Location Labels

Table 3.7.1-8 Location Label List

No. Connection Source (DKC-0) Connection Destination (DKC-1)
Part Name Location Label Color Part Name Location Label Color
Label  Label 
1 CACHE-1CA CL1 1CA-0 White/Black CACHE-1CC CL1 1CC-0 White/Black
2 CACHE-1CA CL1 1CA-1 White/Brown CACHE-1CC CL1 1CC-1 White/Brown
3 CACHE-1CA CL1 1CA-2 White/Red CACHE-1CC CL1 1CC-2 White/Red
4 CACHE-1CA CL1 1CA-3 White/Orange CACHE-1CC CL1 1CC-3 White/Orange
5 CACHE-2CA CL2 2CA-0 Yellow/Black CACHE-2CC CL2 2CC-0 Yellow/Black
6 CACHE-2CA CL2 2CA-1 Yellow/Brown CACHE-2CC CL2 2CC-1 Yellow/Brown
7 CACHE-2CA CL2 2CA-2 Yellow/Red CACHE-2CC CL2 2CC-2 Yellow/Red
8 CACHE-2CA CL2 2CA-3 Yellow/Orange CACHE-2CC CL2 2CC-3 Yellow/Orange

INST03-07-700
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-710

c. Route the MFC Cable (eight cables) on the rear side of the rack, and then pass the MFC
Cable from the rear side to the front side using the jig.

MFC Cable MFC Cable

(CL1 1CA-0, CL1 1CA-1, Locking Clamp (CL1 1CC-0, CL1 1CC-1,
CL1 1CA-2, CL1 1CA-3 CL1 1CC-2, CL1 1CC-3,
CL2 2CA-0, CL2 2CA-1, CL2 2CC-0, CL2 2CC-1,
CL2 2CA-2, CL2 2CA-3) CL2 2CC-2, CL2 2CC-3)

DKC-0

Locking Clamp

DKC-1

Extra Length
Adjustment

Rear View of
RACK

 Attach the cable to the FE  Insert the cable to the rear side  Pull out the cable from the
Cable Jig. of the DKC. front side of the DKC.

MFC Cable
MFC Cable

FE Cable Jig

Rear View of DKC Front View of DKC

Fig. 3.7.1-28 Installation of Cables

INST03-07-710
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-720

d. Route the MFC Cable (eight cables) on the front side of the rack and fix them with the
locking clamps.

Locking Clamp
DKC-0

Locking Clamp

DKC-1

MFC Cable
(CL1 1CA-0,
CL1 1CA-1,
CL1 1CA-2,
MFC Cable
CL1 1CA-3)
(CL2 2CA-0,
CL2 2CA-1,
CL2 2CA-2,
CL2 2CA-3)
MFC Cable
(CL1 1CC-0,
CL1 1CC-1,
CL1 1CC-2,
MFC Cable
CL1 1CC-3)
(CL2 2CC-0, Front View of
CL2 2CC-1, RACK
CL2 2CC-2,
CL2 2CC-3)

Fig. 3.7.1-29 Installation of Cables

INST03-07-720
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-730

e. If the covers are attached to the CM PCBs, remove the covers. And then dispose of the
removed covers.
If the covers are not attached to the CM PCBs, go to Procedure f.
f. Remove the caps from the cables to be connected.
g. Connect the cables to CM PCBs (CACHE-1CA/1CC/2CA/2CC) on the front side of the
DKC-0 and the DKC-1 after checking “3.1.7 Notes when connecting and disconnecting
MFC cable” (INST03-01-190).
DKC-0 DKC-0

CACHE-2CA CACHE-1CA

CL2 2CA-0 CL1 1CA-0

CL2 2CA-1 CL1 1CA-1

CL2 2CA-2 CL1 1CA-2

CL2 2CA-3 CL1 1CA-3

DKC-1 Cover DKC-1 Cover

CACHE-2CC CACHE-1CC

CL2 2CC-0 CL1 1CC-0

CL2 2CC-1 CL1 1CC-1

CL2 2CC-2 CL1 1CC-2

CL2 2CC-3 CL1 1CC-3
Cover Cover
Removal of Cap
Remove a cap while holding the edge of
the cap and the handle of the cable.
Cap

Edge
Handle

Cable

Fig. 3.7.1-30 Connection of Cables

INST03-07-730
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-740

12-6 Installation of Cable Covers and Accessory Box (If the Inter-Controller Connecting Cable
(DKC-F810I-MFC5/MFC30/MFC1J) is installed, this procedure is not necessary.)
a. Install the accessory box into the front of the DKC-0 and fix it with the screw.
b. Install the cable cover into the front of the DKC-0 and fix it with the three screws.
c. Install the cable cover into the rear of the DKC-0 and fix it with the three screws.
d. In the same manner, install the two cable covers and the accessory box in the DKC-1.

12-7 Storing FE Cable Jig

a. Attach the clamp tape to the cleat.
b. Fix the cleat with the screw on the rear side of the rack.
c. Store the FE cable jig on the side of the rack and fasten it with the clamp tape.
If installing the DKC-DKC-F810I-MFC5/MFC30/MFC1J, do not store the FE cable jig at
this moment as the FE cable jig is to be used in later procedures.

Clamp Tape

Screw
(SB406N)
Cleat

Rear View of
RACK

FE Cable Jig

Rear View of Clamp Tape

RACK

Fig. 3.7.1-31 Storing FE Cable Jig

INST03-07-740
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-750

13. Installation Procedure of Inter-Controller Connecting Cable (DKC-F810I-MFC5/MFC30/

MFC1J)
13-1 Removal of Cable Covers and Accessory Box (If they are already removed, this procedure is
not necessary.)
a. Loosen the three screws  on the rear side of the DKC-0 and remove the cable cover.
b. Loosen the screw  and remove the accessory box.

Front View of DKC-x

DKC-x

Accessory Box

Screw 
Front View Screw 

Screw 

Cable Cover

Fig. 3.7.1-32 Removal of Cable Cover and Accessory Box

INST03-07-750
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-760

c. Loosen the three screws on the rear side of the DKC-0 and remove the cable cover.
d. In the same manner, remove the two cable covers and the accessory box from the DKC-1.

Rear View of DKC-x

DKC-x

Cable Cover

Screw

Rear View

Screw

Fig. 3.7.1-33 Removal of Cable Cover

INST03-07-760
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-770

13-2 Installation of Cable

a. Attach 16 location labels to 8 MFC cables. Choose location labels from Labels (Address)
3.
b. Stick the Label (Protect) around the attached location labels.

Location Label  Location Label 

MFC Cable

[Label Attachment Example]

MFC Cable

Location Label

Edge

Label (Protect)

 Attach the location label to the MFC cable.

 Attach the Label (Protect) to the location label with its edge aligned with the location label.
 Stick the Label (Protect) around the location label so that the location label is not torn off.

Fig. 3.7.1-34 Attachment of Location Labels

Table 3.7.1-9 Location Label List

No. Connection Source (DKC-0) Connection Destination (DKC-1)
Part Name Location Label Color Part Name Location Label Color
Label  Label 
1 CACHE-1CB CL1 1CB-0 White/Black CACHE-1CD CL1 1CD-0 White/Black
2 CACHE-1CB CL1 1CB-1 White/Brown CACHE-1CD CL1 1CD-1 White/Brown
3 CACHE-1CB CL1 1CB-2 White/Red CACHE-1CD CL1 1CD-2 White/Red
4 CACHE-1CB CL1 1CB-3 White/Orange CACHE-1CD CL1 1CD-3 White/Orange
5 CACHE-2CB CL2 2CB-0 Yellow/Black CACHE-2CD CL2 2CD-0 Yellow/Black
6 CACHE-2CB CL2 2CB-1 Yellow/Brown CACHE-2CD CL2 2CD-1 Yellow/Brown
7 CACHE-2CB CL2 2CB-2 Yellow/Red CACHE-2CD CL2 2CD-2 Yellow/Red
8 CACHE-2CB CL2 2CB-3 Yellow/Orange CACHE-2CD CL2 2CD-3 Yellow/Orange

INST03-07-770
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-780

c. If you do not have the FE cable jig at hand, take it from the space of storage. (See Fig.
3.7.1-31.)
If you have the FE cable jig at hand, go to Procedure d.
d. Route the MFC Cable (eight cables) on the rear side of the rack, and then pass the MFC
Cable from the rear side to the front side using the jig.
MFC Cable
Locking Clamp
(CL1 1CB-0, CL1 1CB-1,
MFC Cable
CL1 1CB-2, CL1 1CB-3,
(CL1 1CD-0, CL1 1CD-1,
CL2 2CB-0, CL2 2CB-1,
CL1 1CD-2, CL1 1CD-3,
CL2 2CB-2, CL2 2CB-3)
DKC-0 CL2 2CD-0, CL2 2CD-1,
CL2 2CD-2, CL2 2CD-3)

Locking Clamp

DKC-1

Extra Length
Adjustment

Rear View of
RACK

 Attach the cable to the FE  Insert the cable to the rear side  Pull out the cable from the
Cable Jig. of the DKC. front side of the DKC.

MFC Cable
MFC Cable

FE Cable Jig

Rear View of DKC Front View of DKC

Fig. 3.7.1-35 Installation of Cables

INST03-07-780
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-790

e. Route the MFC Cable (eight cables) on the front side of the rack and fix them with the
locking clamps.

Locking Clamp
DKC-0

Locking Clamp

DKC-1

MFC Cable
(CL1 1CB-0,
CL1 1CB-1,
CL1 1CB-2,
MFC Cable
CL1 1CB-3)
(CL2 2CB-0,
CL2 2CB-1,
CL2 2CB-2,
CL2 2CB-3)
MFC Cable
(CL1 1CD-0,
CL1 1CD-1,
CL1 1CD-2,
MFC Cable
CL1 1CD-3)
(CL2 2CD-0,
CL2 2CD-1, Front View of
CL2 2CD-2, RACK
CL2 2CD-3)

Fig. 3.7.1-36 Installation of Cables

INST03-07-790
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-800

f. If the covers are attached to the CM PCBs, remove the covers. And then dispose of the
removed covers.
If the covers are not attached to the CM PCBs, go to Procedure g.
g. Remove the caps from the cables to be connected.
h. Connect the cables to CM PCBs (CACHE-1CB/1CD/2CB/2CD) on the front side of the
DKC-0 and the DKC-1 after checking “3.1.7 Notes when connecting and disconnecting
MFC cable” (INST03-01-190).
DKC-0 DKC-0

CACHE-2CB CACHE-1CB

CL2 2CB-0 CL1 1CB-0

CL2 2CB-1 CL1 1CB-1

CL2 2CB-2 CL1 1CB-2

CL2 2CB-3 CL1 1CB-3

DKC-1 Cover DKC-1 Cover

CACHE-2CD CACHE-1CD

CL2 2CD-0 CL1 1CD-0

CL2 2CD-1 CL1 1CD-1

CL2 2CD-2 CL1 1CD-2

CL2 2CD-3 CL1 1CD-3
Cover Cover
Removal of Cap
Remove a cap while holding the edge of
the cap and the handle of the cable.
Cap

Edge
Handle

Cable

Fig. 3.7.1-37 Connection of Cables

INST03-07-800
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-810

13-3 Installation of Cable Covers and Accessory Box

a. Install the accessory box into the front of the DKC-0 and fix it with the screw.
b. Install the cable cover into the front of the DKC-0 and fix it with the three screws.
c. Install the cable cover into the rear of the DKC-0 and fix it with the three screws.
d. In the same manner, install the two cable covers and the accessory box in the DKC-1.

13-4 Storing FE Cable Jig

a. Store the FE cable jig on the side of the rack and fasten it with the clamp tape. (See Fig.
3.7.1-31.)

INST03-07-810
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-820

14. When you need to install DKC-F810I-MOD5/MOD30/MOD1J, connect the power cables to
the DKCPSs.
When you do not need to install DKC-F810I-MOD5/MOD30/MOD1J, go to Step 15.

a. Connect the four cables to DKCPSs on the rear side of the DKC-1 and secure them with
the cable holders.
b. Push the cable holder in the direction to the DKCPS until it stops.

DKCPS-10 DKCPS-11 DKCPS-12 DKCPS-13

DKCPS-10

Rear View of DKCPS-11

DKC-1

DKCPS-12

DKCPS-13

Cable ASSY
(DKCPS-1PSx0)

Cable ASSY
(DKCPS-1PSx1)

Cable ASSY Cable Holder

(DKCPS-2PSx0)
Cable DKCPS
Cable ASSY
(DKCPS-2PSx1)

Cable Holder
Side View of DKCPS

Fig. 3.7.1-38 Connection of Power Cables

INST03-07-820
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-830

c. Turn on the PDU breaker in the RACK-10 in which the DKC-1 is installed.

[Example]

PDU-1010 PDU-1011

PDU-1000 PDU-1001

DKC-1

Rear View of Breaker

RACK-10

ON

Front View of
PDU

Fig. 3.7.1-39 Turning on the Breaker

INST03-07-830
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-840

15. SVP Pre Procedure (MPB Installation)

(1) <Check that hardware components are installed>
Select (CL) [OK] after making sure that
all hardware components are installed
correctly in response to
“- Connect the LAN cable.
- Insert MODCON-0 and MODCON-1,
and then connect the MODCON cable.
- Connect the MFC cable.
- Connect the cable to the power supplies
(DKCPS-10 DKCPS-11 DKCPS-12
DKCPS-13).
After all the above operations are done, turn the breaker ON and click [OK].”.

NOTE: Confirm that all the PS ENABLE LEDs on the DKC-1 light.
When the breaker of PDU is OFF, please turn it on.

(2)
“Upgrading of the MPB...” is displayed.

(3) <Making sure of completion of the hardware component installation>

A message, “Insert the MPBs on the
storage system. If installation has been
completed, select [OK].
(Note) When MPB(s) has been inserted
before this message is displayed, remove
and insert it again.” is displayed.

NOTE: Do not select (CL) [OK] by

mistake before installing the part(s) to be added in the storage system.

INST03-07-840
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-850

16. Installation Procedure of Additional Processor Blade (DKC-F810I-MP)

NOTICE: Be sure to wear your wrist strap and attach to ground prior to performing the
following work. This will ensure that the IC and LSI on the PCB are protected
from static electricity.

16-1 Insertion of MPBs

a. Loosen the screws and remove the two or four dummy plates. (See Table 3.7.1-10,
Fig. 3.7.1-40 and Fig. 3.7.1-41.)
NOTE: Store the removed dummy plates as they are required when the MPBs are removed.
b. Install the MPBs in the DKC and fix them with the screws.

Main Edge Connector

PCB
NOTICE: • Check that the main edge connector of the PCB has
no deformation, damage or sticking of dust before
installing the PCB. (See INST03-01-80)
• When installing the PCB, hold the top and bottom of
the PCB with both hands, and insert it straight not to
contact the neighboring PCB.

Table 3.7.1-10 MPB installation Location

DKC Additional Slot No. Location No. Remarks
No. Cluster 1 Cluster 2 Cluster 1 Cluster 2
DKC-0 Basic 1MA 2MA MPB-1MA MPB-2MA Standard Equipment
Option 1 1MB 2MB MPB-1MB MPB-2MB
Option 2 1PF 2PF MPB-1PF MPB-2PF
Option 3 1PE 2PE MPB-1PE MPB-2PE
DKC-1 Option 4 1MC 2MC MPB-1MC MPB-2MC Standard Equipment
Option 5 1MD 2MD MPB-1MD MPB-2MD
Option 6 1PM 2PM MPB-1PM MPB-2PM
Option 7 1PL 2PL MPB-1PL MPB-2PL

INST03-07-850
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-860

DKC

Lever Screw

Screw

MPB

Lever Screw
Screw Dummy Plate

Fig. 3.7.1-40 MPB Installation (In the Case of MPB-#MB/#MD)

INST03-07-860
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-870

DKC

Lever Screw

Screw

Dummy
Plate
MPB

Lever Screw
Screw

Fig. 3.7.1-41 MPB installation (In the Case of MPB-#PF/#PE/#PM/#PL)

INST03-07-870
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-880

17. SVP post procedure

(1) <Making sure of completion of the hardware component installation>
After the MPB addition is completed,
select (CL) [OK] in response to a
message, “Insert the MPBs on the storage
system. If installation has been
completed, select [OK].
(Note) When MPB(s) has been inserted
before this message is displayed, remove
and insert it again.”

(2)
“Waiting for Power Event... Usually, several minutes (maximum 15 minutes)” is
displayed.

If [ONL3437E] or [ONL3438E] is displayed, please refer “2.10.1 Replacement procedure

when PCB could not be restoring”. (INST02-420)

(3) <CM Battery charging>

When you select [No] in “2. SVP pre procedure
(Confirmation on the final charge day)”
(INST03-07-110) Step (2), the progress of the
charge is displayed.
When the amount of charge becomes 50% or
more, go to Step (4).
When you select [Cancel] (CL), go to Step (3)-
1.

(3)-1
“Do you want to stop this installation?”
When [Yes] is selected (CL), return to
INST03-07-50 Step (2)
When [No] is selected (CL), return to Step (3).

INST03-07-880
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-890

(4) <End of system update processing>

“Renewal process has completed. Please
check storage system status.” is displayed
when recovery processing on all installed
components is completed. Select (CL)
[OK] in response to this message.

(5)
Execute an operation for backing up the
configuration information.
Prepare the removable media for backup
and insert the media.
Please select (CL) the [Refresh] button,
and update drive information.
Select (CL) the drive and the PC in which
the media was inserted. Select (CL) the
[OK] button.
NOTE: For the procedure of
backing up the configuration
information to a CD-R,
see page MICRO07-190.

INST03-07-890
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07-900

(6)
When this procedure is completed, the message
“Please remove the Config media.” is displayed.
Remove the configuration information media,
select (CL) [OK].

(7)
After the procedure is completed, return to
‘Install’.
Select (CL) [File]-[Exit].

(8) <Mode Change>

Change the mode to View Mode.

Return to the working table and do the rest of the work.

New Installation: INST02-10,
Non-Disruptive Installation: INST02-50

INST03-07-900
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07A-10

3.7.2 Installation of Processor Blade, HUB (DKC-F810I-MP/HUB)

1. Setting up the New Device Structure Information
(1) <Mode Change>
Change the mode to Modify Mode.
Select (CL) [Install].

(2) <Start the ‘Menu Dialog’ screen>

Select (CL) [Change Configuration].

(3) <Start Device Structure Setup screen>

Select (CL) [Installation] in the ‘Menu
Dialog’ dialog box and select (CL) [OK].

(4) <Select a part to be changed>

Select (CL) [MPB + Module], and select
(CL) [OK].

INST03-07A-10
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07A-20

(5) <DKC Configuration screen>

In the ‘DKC Configuration’ screen, when
installation of the MPB is required:
Select (CL) [CHA/DKA/MPB].
Go to Step (6).

After the setting is completed, select (CL)

[>>Next].
Go to Step (8).
In the case of selecting (CL) [Cancel],
this operation procedure terminates.

(6) <CHA/DKA/MPB Configuration screen>

In the ‘CHA/DKA/MPB Configuration’
screen, select the location(s) to which the
addition is to be made, and select (CL)
[Change...].
Go to Step (7).
Make sure that the entry that has been
made is correct and select (CL) [OK].
Go back to Step (5).

(7) <CHA/DKA/MPB Define screen>

In the ‘CHA/DKA/MPB Define’ screen,
select (CL) [MPB].
After the setting is completed, select (CL)
[OK].
Go back to Step (6).

INST03-07A-20
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07A-30

(8) <LDEV Management MPB Configuration screen>

In the ‘LDEV Management MPB
Configuration’ screen, select installed MPB
and select (CL) [Change].
Go to Step (9).

After the setting is completed, select (CL)

[>>Next].
(Go to Step 2)
In the case of selecting (CL) [Cancel], this
operation procedure terminates.

(9) <Auto LDEV Assignment Define screen>

In the ‘Auto LDEV Assignment Define’
screen, select (CL) [Auto LDEV
Assignment].
After the setting is completed, select (CL)
[OK].
Go back to Step (8).

INST03-07A-30
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07A-40

2. SVP pre procedure (HUBBOX Installation)

(1) <Wear a wrist strap>
Select (CL) [OK] in response to “To
prevent serious failures caused by the
static electrical charge, be sure to wear a
wrist strap on your wrist and connect the
earth clip attached on the other side of the
wrist strap to the chassis frame (metal
part) before starting operation.”.

(1)-1 <Confirm wearing wrist strap>

In response to a message, “Did you put on
a wrist strap on your wrist?”.
Select [Yes] when wrist strap is on your
wrist.
Select [No] when there is no wrist strap on
your wrist.
When [No] is selected (CL), go to Step (1)-
2.

(1)-2
In response to a message, “This operation
cannot be excuted, because the wrist strap
has not been worn. Do you want to stop
this process?
[Yes]: This processing will be stopped.
[No]: This confirming message will
appear.”
When [Yes] is selected (CL), the routine
is returned to Step (2) on page INST03-07A-10.
When [No] is selected (CL), returned to Step (1).

INST03-07A-40
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07A-50

(2) <Starting the addition>

In response to a message, “After you
select [Yes], you cannot cancel this
operation. Are you sure you want to
continue this operation?
(Note) Do not install the components for
upgrading the system at this time.”, select
(CL) [Yes].
When [No] is selected (CL), the routine is
returned to Step (2) on page INST03-07A-10.

(3) <HUBBOX Installation Operation>

When installation of the HUBBOX is
required, a message, “Install the
HUBBOX (HUBBOX-nn). After the
operation has completed, select [OK].” is
displayed.

• When the message is displayed, install

the hardware component following the procedure for installing the HUB Kit.
• When the message is not displayed, go to Step (2) in “4. SVP Pre Procedure (MPB
Installation)”.

NOTE: Do not select (CL) [OK] by mistake before installing the part(s) to be added in the
storage system.

INST03-07A-50
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07A-60

3. Installation Procedure of HUB

Installation Condition
The HUB (DKC-F810I-HUB) is an indispensable option that is to be installed when the
storage system configuration is one of the following.

In case of DKC-0
 Addition of the first set (HUBBOX-01)
• The HUBBOX-01 is required to be installed when the MPB is installed in the Option 2
(1PF/2PF) or Option 3 (1PE/2PE) MPB slots.
However, it is not necessary to be installed when two sets of the DKC-F810I-SVP are
installed.

In case of DKC-1
 Addition of the second set (HUBBOX-11)
• The HUBBOX-11 is required to be installed when the MPB is installed in the Option 6
(1PM/2PM) or Option 7 (1PL/2PL) MPB slots.

NOTICE: Be sure to wear your wrist strap and attach to ground prior to performing the
following work. This will ensure that the IC and LSI on the PCB are protected
from static electricity.

INST03-07A-60
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07A-70

3-1 Installation of HUBBOX

a. Loosen the two screws of the HUBBOX slot and remove the dummy plate.

HUBBOX-01 HUBBOX-11

Rear View of DKC-0 Rear View of DKC-1

DKC-x

Screw

Dummy Plate

Screw
Fig. 3.7.2-1 Removal of Dummy Plate

INST03-07A-70
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07A-80

b. Install the HUBBOX and tighten the two screws.

NOTICE: Confirm the vertical direction of the HUBBOX. If the direction is wrong, the
HUBBOX will not be ON.

Rear View
of DKC

HUBBOX

Lever

Screw

Lever
Screw

Top Side

Bottom Side Front View of HUBBOX

Fig. 3.7.2-2 Installation of HUBBOX

INST03-07A-80
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07A-90

3-2 Storage of Dummy Plate

a. Loosen the three screws  on the front side of the DKC and remove the cable cover.
b. Loosen the screw  and remove the accessory box.
c. Put the removed dummy plate in the accessory box.
d. Put the accessory box in place and fix it with the screw .
e. Put the cable cover in place and fix it with the three screws .

Front View of DKC

Dummy Plate

DKC

Accessory Box

Screw 
Front View Screw 

Screw 

Cable Cover

Fig. 3.7.2-3 Storage of Dummy Plate

INST03-07A-90
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07A-100

4. SVP Pre Procedure (MPB Installation)

(1)
When a message, “Install the HUBBOX
(HUBBOX-nn). After the operation has
completed, select [OK].” is displayed,
select (CL) the [OK] button.

(2) <Making sure of completion of the hardware component installation>

A message, “Insert the MPBs on the
storage system. If installation has been
completed, select [OK].
(Note) When MPB(s) has been inserted
before this message is displayed, remove
and insert it again.” is displayed.

NOTE: Do not select (CL) [OK] by

mistake before installing the part(s) to be added in the storage system.

INST03-07A-100
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07A-110

5. Installation Procedure of Additional Processor Blade (DKC-F810I-MP)

NOTICE: Be sure to wear your wrist strap and attach to ground prior to performing the
following work. This will ensure that the IC and LSI on the PCB are protected
from static electricity.

5-1 Insertion of MPBs

a. Loosen the screws and remove the two or four dummy plates. (See Table 3.7.2-1,
Fig. 3.7.2-4 and Fig. 3.7.2-5.)
NOTE: Store the removed dummy plates as they are required when the MPBs are removed.
b. Install the MPBs in the DKC and fix them with the screws.

Main Edge Connector

PCB
NOTICE: • Check that the main edge connector of the PCB has
no deformation, damage or sticking of dust before
installing the PCB. (See INST03-01-80)
• When installing the PCB, hold the top and bottom of
the PCB with both hands, and insert it straight not to
contact the neighboring PCB.

Table 3.7.2-1 MPB installation Location

DKC Additional Slot No. Location No. Remarks
No. Cluster 1 Cluster 2 Cluster 1 Cluster 2
DKC-0 Basic 1MA 2MA MPB-1MA MPB-2MA Standard Equipment
Option 1 1MB 2MB MPB-1MB MPB-2MB
Option 2 1PF 2PF MPB-1PF MPB-2PF
Option 3 1PE 2PE MPB-1PE MPB-2PE
DKC-1 Option 4 1MC 2MC MPB-1MC MPB-2MC Standard Equipment
Option 5 1MD 2MD MPB-1MD MPB-2MD
Option 6 1PM 2PM MPB-1PM MPB-2PM
Option 7 1PL 2PL MPB-1PL MPB-2PL

INST03-07A-110
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07A-120

DKC

Lever Screw

Screw

MPB

Lever Screw
Screw Dummy Plate

Fig. 3.7.2-4 MPB Installation (In the Case of MPB-#MB/#MD)

INST03-07A-120
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07A-130

DKC

Lever Screw

Screw

Dummy
Plate
MPB

Lever Screw
Screw

Fig. 3.7.2-5 MPB installation (In the Case of MPB-#PF/#PE/#PM/#PL)

INST03-07A-130
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07A-140

6. SVP post procedure

(1) <Making sure of completion of the hardware component installation>
After the MPB addition is completed,
select (CL) [OK] in response to a
message, “Insert the MPBs on the storage
system. If installation has been
completed, select [OK].
(Note) When MPB(s) has been inserted
before this message is displayed, remove
and insert it again.”

(2)
“Waiting for Power Event... Usually, several minutes (maximum 15 minutes)” is
displayed.

If [ONL3437E] or [ONL3438E] is displayed, please refer “2.10.1 Replacement procedure

when PCB could not be restoring”. (INST02-420)

(4) <End of system update processing>

“Renewal process has completed. Please
check storage system status.” is displayed
when recovery processing on all installed
components is completed. Select (CL)
[OK] in response to this message.

(5)
Execute an operation for backing up the
configuration information.
Prepare the removable media for backup
and insert the media.
Please select (CL) the [Refresh] button,
and update drive information.
Select (CL) the drive and the PC in which
the media was inserted. Select (CL) the
[OK] button.
NOTE: For the procedure of
backing up the configuration
information to a CD-R,
see page MICRO07-190.

INST03-07A-140
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-07A-150

(6)
When this procedure is completed, the message
“Please remove the Config media.” is displayed.
Remove the configuration information media,
select (CL) [OK].

(7)
After the procedure is completed, return to
‘Install’.
Select (CL) [File]-[Exit].

(8) <Mode Change>

Change the mode to View Mode.

Return to the working table and do the rest of the work.

New Installation: INST02-10,
Non-Disruptive Installation: INST02-50

INST03-07A-150
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08A-10

3.8 Installation of Channel Adapter

3.8.1 Installation of Fibre 8/16-port 8/16G Host Adapter (DKC-F810I-16FC8/8FC16)

Table 3.8.1-1 Parts List

No. Model Number Part Name Part No. Quantity Remarks
1 DKC-F810I-16FC8 WP810-A 5552772-A 2 CHA PCB
2 DKC-F810I-8FC16 WP812-A 5552773-A 2 CHA PCB

INST03-08A-10
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08A-20

Table 3.8.1-2 Working time

Number of change (set) Total (minutes)
CHA Installation 1 15
2 20
3 25
4 30
5 35
6 40
7 45
8 50
9 55
10 60
11 65
12 70
13 75
14 80
15 85

INST03-08A-20
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08A-30

1. Setting up the New Device Structure Information

(1) <Mode Change>
Change the mode to Modify Mode.
Select (CL) [Install].

(2) <Start the ‘Menu Dialog’ screen>

Select (CL) [Change Configuration].

(3) <Start Device Structure Setup screen>

Select (CL) [Installation] in the ‘Menu
Dialog’ dialog box and select (CL) [OK].

(4) <Select a part to be changed>

Select (CL) [Number of Channel], and
select (CL) [OK].

INST03-08A-30
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08A-40

(5) <DKC Configuration screen>

In the ‘DKC Configuration’ screen, select
(CL) [CHA/DKA/MPB].
Go to Step (6).

After the setting is completed, select (CL)

[>>Next].
Go to Step (8).
In the case of selecting (CL) [Cancel],
this operation procedure terminates.

(6) <Setting the CHA type>

In the ‘CHA/DKA/MPB Configuration’
screen, select the location(s) to which the
addition is to be made, and select (CL)
[Change...].
Go to Step (7).
Make sure that the entry that has been
made is correct and select (CL) [OK].
Go back to Step (5).

(7) <Select the CHA type>

In the ‘CHA/DKA/MPB Define’ screen,
select Fibre PCB.
Check the ‘Equip (CL1/CL2)’ setting.
After the setting is completed, select (CL)
[OK]. The routine is returned to Step (5).

INST03-08A-40
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08A-50

(8) <Setting details of the CHA>

Enter the necessary items in the ‘Fibre
PCB Configuration’ screen. Repeat this
operation as many times as the CHAs
installed.

[I/T...]: Change the Target / RCU

Target / Initiator / External for
the port selected.
Go to Step (9).
[Speed...]: Change the channel speed for
the selected port .
Go to Step (10).

Make sure that the items that have been entered are correct and select (CL) [>>Next].

(9) <Setting the Initiator/Target>

Set the type from the Target / RCU Target /
Initiator / External.
After the setting is completed, select (CL) [OK].
Go back to Step (8).

(10) <Setting the channel speed>

Set the channel speed for the channel connected to
the specified port.
After the setting is completed, select (CL) [OK].
Go back to Step (8).

INST03-08A-50
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08A-60

2. SVP pre procedure (Channel Adapter Addition)

(1) <Wear a wrist strap>
Select (CL) [OK] in response to “To
prevent serious failures caused by the
static electrical charge, be sure to wear a
wrist strap on your wrist and connect the
earth clip attached on the other side of the
wrist strap to the chassis frame (metal
part) before starting operation.”.

(1)-1<Confirm wearing wrist strap>

In response to a message, “Did you put on
a wrist strap on your wrist?”.
Select [Yes] when wrist strap is on your
wrist.
Select [No] when there is no wrist strap on
your wrist.
When [No] is selected (CL), go to Step (1)-
2.

(1)-2
In response to a message, “This operation
cannot be excuted, because the wrist strap
has not been worn. Do you want to stop
this process?
[Yes]: This processing will be stopped.
[No]: This confirming message will
appear.”
When [Yes] is selected (CL), the routine
is returned to Step (2) on page INST03-08A-30.
When [No] is selected (CL), returned to Step (1).

INST03-08A-60
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08A-70

(2) <Starting the addition>

In response to a message, “After you
select [Yes], you cannot cancel this
operation. Are you sure you want to
continue this operation? (Note) Do not
insert the components for upgrading the
system at this time.”, select (CL) [Yes].
When [No] is selected (CL), the routine is
returned to Step (2) on page INST03-
08A-30.

INST03-08A-70
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08A-80

(3) <Downloading the microprogram>

The microprogram is downloaded to the SM.
The progress of the downloading is displayed.

(4)
“Changing the storage system configuration data ...” is displayed.

(5) <Making sure of completion of the hardware component installation>

A message, “Insert the CHA on the
storage system. Select [OK] when the
installation has completed.” is displayed.

NOTE: Do not press the [OK] button by

mistake before installing the
part(s) to be added in the storage system.

INST03-08A-80
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08A-90

3. Installation Procedure of Fibre 8/16-port 8/16G Host Adapter

NOTICE: Be sure to wear your wrist strap and attach to ground prior to performing the
following work. This will ensure that the IC and LSI on the PCB are protected
from static electricity.

3-1 Insertion of the PCBs

a. Loosen the screws and remove the dummy plates. (This procedure is not required if the
PCB should be installed in the Basic slots.)
NOTE: Store the removed dummy plates as they are required when the CHAs are removed.

NOTICE: Remove the dummy plate just before installing the PCB.
If the dummy plate is kept removed for a long time, the wind doesn’t flow
among installed PCBs, causing the PCBs’ temperature rise which may result
in temperature warning or temperature alarm.

b. Insert the PCBs to the correct locations in the DKC and tighten the screws.

Main Edge Connector

PCB
NOTICE: • Check that the main edge connector of the PCB has
no deformation, damage or sticking of dust before
installing the PCB. (See INST03-01-80)
• When installing the PCB, hold the top and bottom of
the PCB with both hands, and insert it straight not to
contact the neighboring PCB.

Table 3.8.1-3 Inserting Location

DKC Addition Slot No. Location No. Remarks
No. Cluster 1 Cluster 2 Cluster 1 Cluster 2
DKC-0 Basic 1PC 2PC CHA-1PC CHA-2PC
Option 1 1PD 2PD CHA-1PD CHA-2PD
Option 2 1PE 2PE CHA-1PE CHA-2PE
Option 3 1PF 2PF CHA-1PF CHA-2PF
Option 4 1PB 2PB CHA-1PB CHA-2PB All CHA
Option 5 1PA 2PA CHA-1PA CHA-2PA All CHA
DKC-1 Option 6 1PJ 2PJ CHA-1PJ CHA-2PJ
Option 7 1PK 2PK CHA-1PK CHA-2PK
Option 8 1PL 2PL CHA-1PL CHA-2PL
Option 9 1PM 2PM CHA-1PM CHA-2PM
Option 10 1PH 2PH CHA-1PH CHA-2PH All CHA
Option 11 1PG 2PG CHA-1PG CHA-2PG All CHA

INST03-08A-90
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08A-100

1 1 1 1 1 1 2 2 2 2 2 2 1 1 1 1 1 1 2 2 2 2 2 2
P P P P P P P P PP P P P P P P P P P P P P P P
A B C D E F F E DCB A G H J K L M M L K J HG

Rear View of DKC-0 Rear View of DKC-1

DKC

CHA PCB for Fibre

Lever Screw

Screw

Dummy Plate

Screw
Lever Screw

Fig. 3.8.1-1 Insertion of PCB

INST03-08A-100
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08A-110

3-2 Cleaning the fibre cable connectors

For the tools needed for the cleaning, refer to the tool list on page PARTS05-10.
a. Blow compressed gas against the connector using an air sprayer (for about five seconds).
b. Wipe the connector lightly with a piece of cut gauze wet with ethyl alcohol.
c. Blow compressed air again and check the result of the cleaning (None of dust, sticking of
foreign matter, and dirt must be observed).

INST03-08A-110
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08A-120

3-3 Connection of the optical fibre cables

When wiring for optical fibre cables from the floor

a. Loosen the two screws at the rear bottom of the frame and slide the S/R ASSY forward.
b. Draw the optical fibre cables from the rear lower opening of the frame.

DKC

Optical Fibre
Cable

Screw

Opening

S/R ASSY

Screw
Rear View

Fig. 3.8.1-2 Drawing Optical Fibre Cables

INST03-08A-120
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08A-130

c. Connect the optical fibre cables to the PCB.

In case of DKC-0

CHA (Cluster 1) CHA (Cluster 2)

9A 9C 1A 1C 1E 1G 2G 2E 2C 2A AC AA
BA BC 3A 3C 3E 3G 4G 4E 4C 4A CC CA
DA DC 5A 5C 5E 5G 6G 6E 6C 6A EC EA
FA FC 7A 7C 7E 7G 8G 8E 8C 8A GC GA

9B 9D 1B 1D 1F 1H 2H 2F 2D 2B AD AB
BB BD 3B 3D 3F 3H 4H 4F 4D 4B CD CB
DB DD 5B 5D 5F 5H 6H 6F 6D 6B ED EB
FB FD 7B 7D 7F 7H 8H 8F 8D 8B GD GB

1PA 1PB 1PC 1PD 1PE 1PF 2PF 2PE 2PD 2PC 2PB 2PA
(Op 5) (Op 4) (Basic) (Op 1) (Op 2) (Op 3) (Op 3) (Op 2) (Op 1) (Basic) (Op 4) (Op 5)

PCB
Optical Fibre Cable

TX

RX

Viewed form Top

Fig. 3.8.1-3 Connection of Optical Fibre Cables

INST03-08A-130
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08A-140

In case of DKC-1

CHA (Cluster 1) CHA (Cluster 2)

9J 9L 1J 1L 1N 1Q 2Q 2N 2L 2J AL AJ
BJ BL 3J 3L 3N 3Q 4Q 4N 4L 4J CL CJ
DJ DL 5J 5L 5N 5Q 6Q 6N 6L 6J EL EJ
FJ FL 7J 7L 7N 7Q 8Q 8N 8L 8J GL GJ

9K 9M 1K 1M 1P 1R 2R 2P 2M 2K AM AK
BK BM 3K 3M 3P 3R 4R 4P 4M 4K CM CK
DK DM 5K 5M 5P 5R 6R 6P 6M 6K EM EK
FK FM 7K 7M 7P 7R 8R 8P 8M 8K GM GK

1PG 1PH 1PJ 1PK 1PL 1PM 2PM 2PL 2PK 2PJ 2PH 2PG
(Op 11) (Op 10) (Op 6) (Op 7) (Op 8) (Op 9) (Op 9) (Op 8) (Op 7) (Op 6) (Op 10) (Op 11)

PCB
Optical Fibre Cable

TX

RX

Viewed form Top

Fig. 3.8.1-4 Fixation of Optical Fibre Cables

INST03-08A-140
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08A-150

d. Wire the optical fibre cables to the frame.

e. Slide the S/R ASSY toward you and tighten the two screws.

DKC

Optical Fibre
Cable

Screw

S/R ASSY

Rear View Screw

Fig. 3.8.1-5 Cable Wiring

INST03-08A-150
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08A-160

When wiring for the optical fibre cables from the window opening of the top cover
a. Loosen the two screws of the top cover, and slide the window opening toward the front
side.
b. Draw the optical fibre cables from the opening of the top cover, and wire the cables in the
frame.
c. Connect the optical fibre cables to the PCB in the DKC. (Refer to Fig. 3.8.1-3 or Fig.
3.8.1-4.)
d. Slide the window to close the opening, and retighten it with the two screws.
Screw
Window Opening Window

Screw

Optical Fibre
Cable

DKC

Rear View

Fig. 3.8.1-6 Attachment of Optical Fibre Cables

INST03-08A-160
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08A-170

6. SVP Post-Procedure
(1) <Check that hardware components are installed>
Select (CL) [OK] after making sure that
all hardware components are installed
correctly in response to “Insert the CHA
on the storage system. Select [OK] when
the installation has completed”.

When [Cancel] is selected (CL), returns

to INST03-08A-30 step (3).

(2) <Restore CHA>

“Restoring the CHA...” is displayed.

(3) <End of system update processing>

“Renewal process has completed. Please
check storage system status.” is displayed
when recovery processing on all installed
components is completed. Select (CL)
[OK] in response to this message.

INST03-08A-170
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08A-180

(4)
Execute an operation for backing up the
configuration information.
Prepare the removable media for backup
and insert the media.
Please select (CL) the [Refresh] button,
and update drive information.
Select (CL) the drive and the PC in which
the media was inserted. Select (CL) the
[OK] button.
NOTE: For the procedure of
backing up the configuration
information to a CD-R,
see page MICRO07-190.

(5)
When this procedure is completed, the message
“Please remove the Config media.” is displayed.
Remove the configuration information media, select
(CL) [OK].

(6)
After the procedure is completed, return to
‘Install’.
Select (CL) [File]-[Exit].

(7) <Mode Change>

Change the mode to View Mode.

Return to the working table and do the rest of the work.

New Installation: INST02-20,
Non-Disruptive Installation: INST02-50

INST03-08A-180
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08B-10

3.8.2 Installation of Mainframe Fibre 16-port 8G Host Adapter (DKC-F810I-16MS8/16ML8)

Table 3.8.2-1 Parts List

No. Model Number Part Name Part No. Quantity Remarks
1 DKC-F810I-16MS8 WP811-A 5552775-A 2 CHA PCB
2 DKC-F810I-16ML8 WP811-B 5552776-A 2 CHA PCB

INST03-08B-10
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08B-20

Table 3.8.2-2 Working time

Number of change (set) Total (minutes)
CHA Installation 1 15
2 20
3 25
4 30
5 35
6 40
7 45
8 50
9 55
10 60
11 65
12 70
13 75
14 80
15 85

INST03-08B-20
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08B-30

1. Setting up the New Device Structure Information

(1) <Mode Change>
Change the mode to Modify Mode.
Select (CL) [Install].

(2) <Start the ‘Menu Dialog’ screen>

Select (CL) [Change Configuration].

(3) <Start Device Structure Setup screen>

Select (CL) [Installation] in the ‘Menu
Dialog’ dialog box and select (CL) [OK].

(4) <Select a part to be changed>

Select (CL) [Number of Channel], and
select (CL) [OK].

INST03-08B-30
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08B-40

(5) <DKC Configuration screen>

In the ‘DKC Configuration’ screen, select
(CL) [CHA/DKA/MPB].
Go to Step (6).

After the setting is completed, select (CL)

[>>Next].
Go to Step (8).
In the case of selecting (CL) [Cancel],
this operation procedure terminates.

(6) <Setting the CHA type>

In the ‘CHA/DKA/MPB Configuration’
screen, select the location(s) to which the
addition is to be made, and select (CL)
[Change...].
Go to Step (7).
Make sure that the entry that has been
made is correct and select (CL) [OK].
Go back to Step (5).

(7) <Select the CHA type>

In the ‘CHA/DKA/MPB Define’ screen,
select Mfibre PCB.
After the setting is completed, select (CL)
the [OK].
Go back to Step (6).

INST03-08B-40
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08B-50

(8) <Mainframe PCB Configuration screen>

Enter the necessary items in the
‘Mainframe PCB Configuration’ screen.
Repeat this operation as many times as
the CHAs installed.

[FNP...]: Set the HTP/FNP for the

selected port.
Go to Step (9).
[CU Num...]: Set the number of the CU
connected to the selected
port.
Go to Step (10).
[Emulation...]: Set the DKC Emulation for the selected port.
Go to Step (11).

Make sure that the items that have been entered are correct and select (CL) [>>Next].
Go to Step (12).

NOTE: The setting of “CU Number” cannot be done for the definition that crosses
16KLDEV boundary (00:00-00:3F/00:40-00:7F/00:80-00:BF/00:C0-00:FE) for
per two ports. When the definition that crosses 16KLDEV boundary is done, it is
defined for per two ports.

(9) <Setting the HTP/FNP>

Set the HTP/FNP.
After the setting is completed, select (CL) the
[OK].
Go back to Step (8).

INST03-08B-50
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08B-60

(10) <Setting the CU number>

Set the number of the LDKC/CU connected to the
specified port.
After the setting is completed, select (CL) the [OK].
Go back to Step (8).

(11) <Setting the DKC Emulation>

Set the DKC Emulation.
After the setting is completed, select (CL)
the [OK].
Go back to Step (8).

(12) <Display of the SVP message>

In response to the message, “Data will be
lost from the logical device if you connect
the interface cable to an incorrect port. Be
sure to connect the cable to the correct
port.”, select (CL) [OK].

INST03-08B-60
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08B-70

2. SVP pre procedure (Channel Adapter Addition)

(1) <Wear a wrist strap>
Select (CL) [OK] in response to “To
prevent serious failures caused by the
static electrical charge, be sure to wear a
wrist strap on your wrist and connect the
earth clip attached on the other side of the
wrist strap to the chassis frame (metal
part) before starting operation.”.

(1)-1 <Confirm wearing wrist strap>

In response to a message, “Did you put on
a wrist strap on your wrist?”.
Select [Yes] when wrist strap is on your
wrist.
Select [No] when there is no wrist strap on
your wrist.
When [No] is selected (CL), go to Step (1)-
2.

(1)-2
In response to a message, “This operation
cannot be excuted, because the wrist strap
has not been worn. Do you want to stop
this process?
[Yes]: This processing will be stopped.
[No]: This confirming message will
appear.”
When [Yes] is selected (CL), the routine
is returned to Step (2) on page INST03-08B-30.
When [No] is selected (CL), returned to Step (1).

INST03-08B-70
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08B-80

(2) <Starting the addition>

In response to a message, “After you
select [Yes], you cannot cancel this
operation. Are you sure you want to
continue this operation? (Note) Do not
insert the components for upgrading the
system at this time.”, select (CL) [Yes].
When [No] is selected (CL), the routine is
returned to Step (2) on page INST03-
08B-30.

INST03-08B-80
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08B-90

(3) <Downloading the microprogram>

The microprogram is downloaded to the SM.
The progress of the downloading is displayed.

(4)
“Changing the storage system configuration data ...” is displayed.

(5) <Making sure of completion of the hardware component installation>

A message, “Insert the CHA on the
storage system. Select [OK] when the
installation has completed.” is displayed.

NOTE: Do not press the [OK] button by

mistake before installing the
part(s) to be added in the storage system.

INST03-08B-90
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08B-100

3. Installation Procedure of Mainframe Fibre 16-port 8G Host Adapter

NOTICE: Be sure to wear your wrist strap and attach to ground prior to performing the
following work. This will ensure that the IC and LSI on the PCB are protected
from static electricity.

3-1 Insertion of the PCBs

a. Loosen the screws and remove the dummy plates. (This procedure is not required if the
PCB should be installed in the Basic slots.)
NOTE: Store the removed dummy plates as they are required when the CHAs are removed.

NOTICE: Remove the dummy plate just before installing the PCB.
If the dummy plate is kept removed for a long time, the wind doesn’t flow
among installed PCBs, causing the PCBs’ temperature rise which may result
in temperature warning or temperature alarm.

b. Insert the PCBs to the correct locations in the DKC and tighten the screws.

Main Edge Connector

PCB
NOTICE: • Check that the main edge connector of the PCB has
no deformation, damage or sticking of dust before
installing the PCB. (See INST03-01-80)
• When installing the PCB, hold the top and bottom of
the PCB with both hands, and insert it straight not to
contact the neighboring PCB.

Table 3.8.2-3 Inserting Location

DKC Addition Slot No. Location No. Remarks
No. Cluster 1 Cluster 2 Cluster 1 Cluster 2
DKC-0 Basic 1PC 2PC CHA-1PC CHA-2PC
Option 1 1PD 2PD CHA-1PD CHA-2PD
Option 2 1PE 2PE CHA-1PE CHA-2PE
Option 3 1PF 2PF CHA-1PF CHA-2PF
Option 4 1PB 2PB CHA-1PB CHA-2PB All CHA
Option 5 1PA 2PA CHA-1PA CHA-2PA All CHA
DKC-1 Option 6 1PJ 2PJ CHA-1PJ CHA-2PJ
Option 7 1PK 2PK CHA-1PK CHA-2PK
Option 8 1PL 2PL CHA-1PL CHA-2PL
Option 9 1PM 2PM CHA-1PM CHA-2PM
Option 10 1PH 2PH CHA-1PH CHA-2PH All CHA
Option 11 1PG 2PG CHA-1PG CHA-2PG All CHA

INST03-08B-100
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08B-110

1 1 1 1 1 1 2 2 2 2 2 2 1 1 1 1 1 1 2 2 2 2 2 2
P P P P P P P P PP P P P P P P P P P P P P P P
A B C D E F F E DCB A G H J K L M M L K J HG

Rear View of DKC-0 Rear View of DKC-1

DKC

CHA PCB for

Mainframe Fibre

Lever Screw

Screw

Dummy Plate

Screw
Lever Screw

Fig. 3.8.2-1 Insertion of PCB

INST03-08B-110
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08B-120

3-2 Cleaning the fibre cable connectors

For the tools needed for the cleaning, refer to the tool list on page PARTS05-10.
a. Blow compressed gas against the connector using an air sprayer (for about five seconds).
b. Wipe the connector lightly with a piece of cut gauze wet with ethyl alcohol.
c. Blow compressed air again and check the result of the cleaning (None of dust, sticking of
foreign matter, and dirt must be observed).

INST03-08B-120
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08B-130

3-3 Connection of the optical fibre cables

When wiring for optical fibre cables from the floor

a. Loosen the two screws at the rear bottom of the frame and slide the S/R ASSY forward.
b. Draw the optical fibre cables from the rear lower opening of the frame.

DKC

Optical Fibre
Cable

Screw

Opening

S/R ASSY

Screw
Rear View

Fig. 3.8.2-2 Drawing Optical Fibre Cables

INST03-08B-130
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08B-140

c. Connect the optical fibre cables to the PCB.

In case of DKC-0

CHA (Cluster 1) CHA (Cluster 2)

9A 9C 1A 1C 1E 1G 2G 2E 2C 2A AC AA
BA BC 3A 3C 3E 3G 4G 4E 4C 4A CC CA
DA DC 5A 5C 5E 5G 6G 6E 6C 6A EC EA
FA FC 7A 7C 7E 7G 8G 8E 8C 8A GC GA

9B 9D 1B 1D 1F 1H 2H 2F 2D 2B AD AB
BB BD 3B 3D 3F 3H 4H 4F 4D 4B CD CB
DB DD 5B 5D 5F 5H 6H 6F 6D 6B ED EB
FB FD 7B 7D 7F 7H 8H 8F 8D 8B GD GB

1PA 1PB 1PC 1PD 1PE 1PF 2PF 2PE 2PD 2PC 2PB 2PA
(Op 5) (Op 4) (Basic) (Op 1) (Op 2) (Op 3) (Op 3) (Op 2) (Op 1) (Basic) (Op 4) (Op 5)

PCB
Optical Fibre Cable

TX

RX

Viewed form Top

Fig. 3.8.2-3 Connection of Optical Fibre Cables

INST03-08B-140
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08B-150

In case of DKC-1

CHA (Cluster 1) CHA (Cluster 2)

9J 9L 1J 1L 1N 1Q 2Q 2N 2L 2J AL AJ
BJ BL 3J 3L 3N 3Q 4Q 4N 4L 4J CL CJ
DJ DL 5J 5L 5N 5Q 6Q 6N 6L 6J EL EJ
FJ FL 7J 7L 7N 7Q 8Q 8N 8L 8J GL GJ

9K 9M 1K 1M 1P 1R 2R 2P 2M 2K AM AK
BK BM 3K 3M 3P 3R 4R 4P 4M 4K CM CK
DK DM 5K 5M 5P 5R 6R 6P 6M 6K EM EK
FK FM 7K 7M 7P 7R 8R 8P 8M 8K GM GK

1PG 1PH 1PJ 1PK 1PL 1PM 2PM 2PL 2PK 2PJ 2PH 2PG
(Op 11) (Op 10) (Op 6) (Op 7) (Op 8) (Op 9) (Op 9) (Op 8) (Op 7) (Op 6) (Op 10) (Op 11)

PCB
Optical Fibre Cable

TX

RX

Viewed form Top

Fig. 3.8.2-4 Fixation of Optical Fibre Cables

INST03-08B-150
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08B-160

d. Wire the optical fibre cables to the frame.

e. Slide the S/R ASSY toward you and tighten the two screws.

DKC

Optical Fibre
Cable

Screw

S/R ASSY

Rear View Screw

Fig. 3.8.2-5 Cable Wiring

INST03-08B-160
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08B-170

When wiring for the optical fibre cables from the window opening of the top cover
a. Loosen the two screws of the top cover, and slide the window opening toward the front
side.
b. Draw the optical fibre cables from the opening of the top cover, and wire the cables in the
frame.
c. Connect the optical fibre cables to the PCB in the DKC. (Refer to Fig. 3.8.2-3 or Fig.
3.8.2-4.)
d. Slide the window to close the opening, and retighten it with the two screws.
Screw
Window Opening Window

Screw

Optical Fibre
Cable

DKC

Rear View

Fig. 3.8.2-6 Attachment of Optical Fibre Cables

INST03-08B-170
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08B-180

4. SVP Post-Procedure
(1) <Check that hardware components are installed>
Select (CL) [OK] after making sure that
all hardware components are installed
correctly in response to “Insert the CHA
on the storage system. Select [OK] when
the installation has completed.”.

When [Cancel] is selected (CL), returns

to INST03-08B-30 step (3).

(2) <Restore CHA>

“Restoring the CHA...” is displayed.

(3) <End of system update processing>

“Renewal process has completed. Please
check storage system status.” is displayed
when recovery processing on all installed
components is completed. Select (CL)
[OK] in response to this message.

INST03-08B-180
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-08B-190

(4)
Execute an operation for backing up the
configuration information.
Prepare the removable media for backup
and insert the media.
Please select (CL) the [Refresh] button,
and update drive information.
Select (CL) the drive and the PC in which
the media was inserted. Select (CL) the
[OK] button.
NOTE: For the procedure of
backing up the configuration
information to a CD-R,
see page MICRO07-190.

(5)
When this procedure is completed, the message
“Please remove the Config media.” is displayed.
Remove the configuration information media, select
(CL) [OK].

(6)
After the procedure is completed, return to
‘Install’.
Select (CL) [File]-[Exit].

(7) <Mode Change>

Change the mode to View Mode.

Return to the working table and do the rest of the work.

New Installation: INST02-20,
Non-Disruptive Installation: INST02-50

INST03-08B-190
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-09-10

3.9 Changing of SFP (DKC-F810I-1PL8/1PS8/1PL16/1PS16)

NOTICE: 1. The SFP (DKC-F810I-1PL8/1PS8) is an option to change the transceiver

installed in the CHA package of the 8Gbps Fibre (DKC-F810I-16FC8) to a
port corresponding to Longwave or Shortwave. It cannot be installed in the
other CHA (DKC-F810I-8FC16/16MS8/16ML8).
2. The SFP (DKC-F810I-1PL16/1PS16) is an option to change the transceiver
installed in the CHA package of the 16Gbps Fibre (DKC-F810I-8FC16) to a
port corresponding to Longwave or Shortwave. It cannot be installed in the
other CHA (DKC-F810I-16FC8/16MS8/16ML8).
3. Note that you cannot just change between Longwave and Shortwave SFP
transceivers in an existing configuration without considering the cables.
Longwave requires 9 micrometer diameter, single mode cable, and
Shortwave requires 50/62.5 micrometer diameter, multimode cable.
The Customer will encounter many CRC and Loss of Sync errors should they
replace only transceivers and try to reuse the pre-existing cables that do not
match the transceivers.

Table 3.9-1 Parts List

No. Model Number Part Name Part No. Quantity Remarks
1 DKC-F810I-1PL8 SFP (LONG) 5556750-A 1
2 DKC-F810I-1PS8 SFP (SHORT) 5557409-A 1
5541873-B
3 DKC-F810I-1PL16 SFP (LONG) 5552782-A 1
4 DKC-F810I-1PS16 SFP (SHORT) 5552781-A 1

INST03-09-10
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-09-20

NOTICE: Before the replacement, make sure that a host device has been disconnected.

1. SFP type change

(1) <Preparation>
Close the all SVP menu.

(2) <Input password>

Select “Shift” + “Ctrl” + “F” on the SVP window.
Enter the password “RAID-SFP” and select (CL) [OK].

(3) <Check the mode>

The ‘SFP Mode’ is Displayed.

INST03-09-20
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-09-30

2. Changing Procedure of SFP

NOTICE: Be sure to wear your wrist strap and attach to ground prior to performing the
following work. This will ensure that the IC and LSI on the PCB are protected
from static electricity.

2-1 Replacement of SFP

a. Make sure of the CHA and Port Locations of the SFP to be replaced. (Refer to pages
LOC04-10 through LOC04-30.)

CAUTION
If the SFP of a wrong port is removed, a system down may be caused. Make sure that the
location of the SFP to be replaced is correct.

b. Disconnect the optical fibre cable or protector from the SFP to be replaced.

CHA PCB

SFP

Optical Fibre Cable

Protector

Fig. 3.9-1 Disconnection of Cable or Protector

INST03-09-30
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-09-40

c. Open the lever on the SFP toward you with your finger.
d. Pull the opened lever and remove the SFP.
NOTE: Be careful so that the claw of the SFP lever does not hurt your finger.

CHA PCB

Lever

TX

RX

SFP
Claw

SFP

Fig. 3.9-2 Removal of SFP

INST03-09-40
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-09-50

e. Insert the optional SFP to the CHA PCB.

NOTICE: Because the SFP that has been removed is a user’s property, return it to and
ask the user to keep it in custody.

How to distinguish between SFP (SHORT) and SFP (LONG)

The whole or a part of the lever is a black for the SFP (SHORT).
The whole or a part of the lever is a blue for the SFP (LONG).

[Example]

SFP (SHORT) SFP (LONG)

Lever Color: Black Lever Color: Blue

Fig. 3.9-3 How to distinguish SFP

INST03-09-50
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-09-60

3. Check SFP Kind information

(1) <Instruction of DKC Information>
Select (CL) [DKC-n].

(2) <Display of DKC-n Back Information>

Select (CL) [DKC-n Back].

(3) <Display of CHA Information>

Select (CL) [CHA-nXX] which installs
SFP of the maintenance target.

INST03-09-60
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-09-70

(4) <Check SFP Kind information>

Make sure that information on the SFP
Kind is displayed at the CHA location
where the setting was changed and that the
SFP Kind information on the port where
the replacement was made is consistent
with the specified setting.
When the SFP Kind information is not
displayed, check if the SFP is installed
correctly. If the SFP is installed correctly,
replace it with a part for maintenance.

SFP Kind information

4. Return to the working table and do the rest of the work.

New Installation: INST02-20
Non-Disruptive Installation: INST02-50
Non-Disruptive De-Installation: INST02-80

INST03-09-70
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-10

3.10 Installation of Cache Memory, Cache Backup Module kit, Cache Flash Memory and
Inter-Controller Connecting Cable (DKC-F810I-CM16G/CM32G/CPEX/BKMS/BKML/
BMM128/BMM256/MFC5/MFC30/MFC1J)

Table 3.10-1 Parts List

No. Model Number Part Name Part No. Quantity Remarks
1 DKC-F810I-CM16G 16GB DIMM 5552764-A 1 CM Module
2 DKC-F810I-CM32G 32GB DIMM 5552765-A 1 CM Module
3 DKC-F810I-CPEX WP840-A 5552763-A 2 CM PCB (*1)
HU Jumper 5521578-1 2 Maintenance Jumper
4 DKC-F810I-BKMS BKM 5552766-A 2
5 DKC-F810I-BKML BKM 5552767-A 2
6 DKC-F810I- SSD (128GB) 5552768-A 1 CFM
BMM128 Screw SB305N 2
7 DKC-F810I- SSD (256GB) 5552769-A 1 CFM
BMM256 Screw SB305N 2
8 DKC-F810I-MFC5 MFC Cable 5552752-A 8
Label (Address) 3 3287145-1 3
Label (Protect) 3287450-1 3
FE Cable Jig 5555008-A 1
Packing Work (PARTS) 3287318-C 1
Screw SB406N 1 (*2)
Cleat 5409055-2 1 (*2)
Clamp Tape 5544251-3 1 (*2)
9 DKC-F810I-MFC30 MFC Cable 5555155-A 8
Label (Address) 3 3287145-1 3
Label (Protect) 3287450-1 3
FE Cable Jig 5555008-A 1
Packing Work (PARTS) 3287318-C 1
Screw SB406N 1 (*2)
Cleat 5409055-2 1 (*2)
Clamp Tape 5544251-3 1 (*2)
(To be continued)

INST03-10-10
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-20

(Continued from the preceding page)

No. Model Number Part Name Part No. Quantity Remarks
10 DKC-F810I-MFC1J MFC Cable 5552753-A 8
Label (Address) 3 3287145-1 3
Label (Protect) 3287450-1 3
FE Cable Jig 5555008-A 1
Packing Work (PARTS) 3287318-C 1
Screw SB406N 1 (*2)
Cleat 5409055-2 1 (*2)
Clamp Tape 5544251-3 1 (*2)

*1: CM PCB is a name of the cache board (WP840-A) that is included in the DKC-F810I-
CPEX. The name is used in the following procedures.
*2: These parts are included in Packing Work (PARTS).

Rough time of Cache memory and/or cache flash memory installation becomes addition of the
following A, B, C and D.

Table 3.10-2 Rough time of installation

Process Time
A Target CM PCB blocking time 5 ~ 60min × 2 (*1)
B Cache memory, CFM equipment Cache memory module: 6min × target CM PCB num.
process CFM: 7.5min × target CM PCB num.
C Target CM PCB diagnosis time Target CM PCB diagnosis time 10min × target CM PCB num.
D Target CM PCB recovering time Target CM PCB recovering time 5 ~ 20min × target CM PCB
num. (*1)

*1: Standard processing time is indicated. The processing time depends on the use situation,
especially, the influence of the amount of write pending is received. When the amount of
write pending is large, time more than the indication value might be required.

INST03-10-20
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-30

(Reference) Outline of the recommended procedure for installation

(1) When adding PCBs from two (CM16G×12) to four (CM16G×16) (DIMM and PCB
installation)

(a) Installation with priority on minimizing impact on host (without cache side blockade)

CM16G
Module #0

PCB#0 PCB#2

Power
PCB#1 PCB#3 boundary

Area to
install

 Install PCB#2, #3 (CM16G×16)

Area not
installed

Module #0

PCB#0 PCB#2

Power
PCB#1 PCB#3 boundary

 Install DIMM in PCB#0, #1

Area to
install

Module #0

PCB#0 PCB#2

Power
PCB#1 PCB#3 boundary

Fig. 3.10-1 Installation with priority on minimizing impact on host 1

INST03-10-30
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-40

(b) Installation with priority on reducing maintenance time (with cache side blockade)

Module #0

PCB#0 PCB#2

Power
PCB#1 PCB#3 boundary

Area to  Perform PCB#2, #3 (CM16G×16) installation and

install PCB#0, #1 DIMM installation at the same time

Module #0

PCB#0 PCB#2

Power
PCB#1 PCB#3 boundary

Fig. 3.10-2 Installation with priority on reducing maintenance time 1

INST03-10-40
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-50

(2) When adding PCBs from two (CM16G×16 [SM area is 8G, DIR+CM area is 24G) to four
(two sets of CM16G×16 [SM area is 16G, DIR+CM area is 16G] and two sets of
CM16G×16 [DIR+CM area is 32G]) (PCB and SM area Installation)

(a) Installation with priority on minimizing impact on host (without cache side blockade)

CM16G×16 (SM area is 8G, DIR+CM area is 24G)

Module #0

PCB#0 PCB#2

Power
PCB#1 PCB#3 boundary

Area to
install  Install PCB#2, #3 (CM16G×16)

CM16G×16 (SM area is 8G, DIR+CM area is 24G)

Module #0

PCB#0 PCB#2

Power
PCB#1 PCB#3 boundary

 Install SM (8G to 16G)

CM16G×16 (SM area is 16G, DIR+CM area is 16G)

Module #0

PCB#0 PCB#2

Power
PCB#1 PCB#3 boundary

Fig. 3.10-3 Installation with priority on minimizing impact on host 2

INST03-10-50
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-60

(b) Installation with priority on reducing maintenance time (with cache side blockade)

CM16G×16 (SM area is 8G, DIR+CM area is 24G)

Module #0

PCB#0 PCB#2

Power
PCB#1 PCB#3 boundary

Area to
install  Perform PCB#2, #3 (CM16G×16) Installation and SM
installation (8G to 16G) at the same time

CM16G×16 (SM area is 16G, DIR+CM area is 16G)

Module #0

PCB#0 PCB#2

Power
PCB#1 PCB#3 boundary

Fig. 3.10-4 Installation with priority on reducing maintenance time 2

INST03-10-60
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-70

(3) When adding PCBs from 8 (CM16G×12) to 8 (CM16G×16) (DIMM installation)

(a) Installation with priority on minimizing impact on host (without cache side blockade)

Module #0 Module #1
PCB#0 PCB#2 PCB#4 PCB#6

Power
boundary
PCB#1 PCB#3 PCB#5 PCB#7

Area to install  Divide PCBs into 2 (in half) and install DIMMs in
separate 2 operations (Make sure to perform PCB#0,
#1 installation and PCB#2, #3 installation separately)

Module #0 Module #1
PCB#0 PCB#2 PCB#4 PCB#6

Power
boundary
PCB#1 PCB#3 PCB#5 PCB#7

Area to install
 Install remaining DIMM for PCB

Module #0 Module #1
PCB#0 PCB#2 PCB#4 PCB#6

Power
boundary
PCB#1 PCB#3 PCB#5 PCB#7

Fig. 3.10-5 Installation with priority on minimizing impact on host 3

INST03-10-70
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-80

(b) Installation with priority on reducing maintenance time (with cache side blockade)

Module #0 Module #1
PCB#0 PCB#2 PCB#4 PCB#6

Power
boundary
PCB#1 PCB#3 PCB#5 PCB#7

Area to install
 Install DIMM in PCB#0 to #F

Module #0 Module #1
PCB#0 PCB#2 PCB#4 PCB#6

Power
boundary
PCB#1 PCB#3 PCB#5 PCB#7

Fig. 3.10-6 Installation with priority on reducing maintenance time 3

INST03-10-80
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-90

(4) When adding PCBs from 8 (CM16G×16) to 8 (CM32G×8) (DIMM type change and
DIMM installation)

(a) Change the DIMM type from CM16G×16 to CM32G×8 of 8 PCBs as shown in Fig.
3.10-7 below.
(See the SVP SECTION, “2.27 Change CM Module group size” (SVP02-27-10))

CM16G
Module #0 Module #1
PCB#0 PCB#2 PCB#4 PCB#6

Power
PCB#1 PCB#3 PCB#5 PCB#7 boundary

DIMM type change

 Change PCB#0 to #F (CM16G×16) to
(CM32G×8) one by one (See SVP02-27-10)

Module #0 Module #1 CM32G

PCB#0 PCB#2 PCB#4 PCB#6

Power
PCB#1 PCB#3 PCB#5 PCB#7 boundary

Fig. 3.10-7 Changing of DIMM type

(b) Perform one of the following installations depending on which to prioritize,

minimizing impact on host or maintenance time reduction.

 Installation with priority on minimizing impact on host (without cache side

blockade)
After changing the DIMM type, perform installation in accordance with the
procedure in INST03-10-70 (3) (a).

 Installation with priority on reducing maintenance time (with cache side blockade)
After changing the DIMM type, perform installation in accordance with the
procedure in INST03-10-80 (3) (b).

INST03-10-90
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-100

1. Installation Procedure of Inter-Controller Connecting Cable (DKC-F810I-MFC5/MFC30/

MFC1J)
(1) When you need to install Inter-Controller Connecting Cable (DKC-F810I-MFC5/MFC30/
MFC1J), install the eight cables to the rack. See “3.7.1 Installation of Module procedure 13
(INST03-07-750 through 810)”.
When you do not need to install Inter-Controller Connecting Cable (DKC-F810I-MFC5/
MFC30/MFC1J), go to procedure 2.

INST03-10-100
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-110

2. Setting up the New Device Structure Information.

(1) <Mode Change>
Change the mode to Modify Mode.
Select (CL) [Install].

(2) <Start the ‘Menu Dialog’ screen>

Select (CL) [Change Configuration].

(3) <Start Device Structure Setup screen>

Select (CL) [Installation] in the ‘Menu
Dialog’ dialog box and select (CL) [OK].

(4) <Select a part to be changed>

Select (CL) [Cache Capacity], and select
(CL) [OK].

INST03-10-110
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-120

(5) <DKC Configuration screen>

In the ‘DKC Configuration’ screen, select
(CL) [Cache].
Go to Step (6).

NOTE: It is impossible to install

multiple types of parts at the
same time.

Make sure that the all input items are

correct and select (CL) [>>Next].
Go to Step (7).

If the PCB install is not done, go to Step

(8).

(6) <Cache Configuration screen>

In the ‘Cache Configuration’ screen,
define each item.

When the change of Cache setting or

installation of the PCB is required, select
(CL) the target Cache PCB and then
select (CL) [Cache Size].
Go to Step (6)-1.

When the change of BKM setting is

required, select (CL) [BKM].
Go to Step (6)-2.

When the change of SM setting is required, select (CL) [SM function].

Go to Step (6)-3.

When the change of DCR setting is required, select (CL) [DCR Change].
Go to Step (6)-4.

When the change of CLPR setting is required, select (CL) the target CLPR. and then select
(CL) [Set CLPR].
Go to Step (6)-5.

After setting all items, select (CL) [OK].

Go back to Step (5).

INST03-10-120
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-130

(6)-1 <Cache Size Define screen>

Set the CMG/Cache Size in the ‘Cache Size
Define’ screen, and then select (CL) [OK].
Go back to Step (6).

(6)-2 <BKM screen>

Set the BKM in the ‘BKM Define’ screen, select
(CL) [OK].
Go back to Step (6).

(6)-3 <SM function Define screen>

Set the SM function in the ‘SM function
Define’ screen, select (CL) [OK].
Go back to Step (6).

(6)-4 <DCR Available Size Define screen>

Set the DCR available size in the ‘DCR Available
Size Define’ screen, select (CL) [OK].
Go back to Step (6).

INST03-10-130
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-140

(6)-5 <CLPR Define screen>

Set the Cache Size/DCR available
Size/Number of extent in the ‘CLPR Define’
screen, select (CL) [OK].
Go back to Step (6).

(7) <Battery Life Warning SIM screen>

Select (CL) the target CM Battery in the
‘Battery Life Warning SIM’ screen, and
then select (CL) [Set...].
Go to Step (7)-1.

Make sure that the all input items are

correct and select (CL) [OK].
Go to Step (8).

NOTE: If the date is displayed as

“****/**/**”, follow Step (7)-1
to set the date.

NOTE: When the check box of Battery Life Warning SIM is unchecked, the ‘Battery Life
Warning SIM’ screen is not displayed for non-notice setting.
Go to Step (8).

(7)-1 <Battery Life Warning SIM screen>

Select (CL) [OK] after inputting the remainder
days until Warning SIM is reported.
Return to Step (7).

NOTE: After executing the periodical

exchange of a battery, set 33 month (990 days).
NOTE: Default value is 33 month (990 days), which is 3 month earlier than the lifetime of
a battery (3 years).
Determine the number of days remained based on your maintenance plan.
NOTE: The input ranges of “Remained Battery life” are from 1 to 3650.

INST03-10-140
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-150

(8) <Wear a wrist strap>

Select (CL) [OK] in response to “To
prevent serious failures caused by the
static electrical charge, be sure to wear a
wrist strap on your wrist and connect the
earth clip attached on the other side of the
wrist strap to the chassis frame (metal
part) before starting operation.”.

(8)-1 <Confirm wearing wrist strap>

In response to a message, “Did you put on
a wrist strap on your wrist?”.
Select [Yes] when wrist strap is on your
wrist.
Select [No] when there is no wrist strap on
your wrist.
When [No] is selected (CL), go to Step (8)-
2.

(8)-2
In response to a message, “This operation
cannot be excuted, because the wrist strap
has not been worn. Do you want to stop
this process?
[Yes]: This processing will be stopped.
[No]: This confirming message will
appear.”
When [Yes] is selected (CL), the routine
is returned to Step (2) on page INST03-10-110.
When [No] is selected (CL), returned to Step (8).

INST03-10-150
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-160

3. SVP pre procedure (Battery)

(1) <Confirmation on the final charge day>
Select (CL) [Yes] in response to “Check
the last charged dates described in the
batteries. Are the last charged dates for all
of the batteries that are target to be added
indicated within six months?”
Go to Step 4.
When [No] is selected (CL), go to Step
(2).

(2)
“The backup cannot be ensured with the
battery of last charged date is more than
six months ago. To continue this process,
the maximum 135 minutes of
maintenance hour is required to add to the
usual maintenance hour. Do you want to
stop this process?”

When [Yes] is selected (CL), returns to

INST03-10-110 Step (2).
When [No] is selected (CL), go to Step (3).

(3) <Input password>

Enter the password and select (CL) [OK].

CAUTION
This is a special (exceptional) operation that can cause a serious failure such as a
system down or a data loss if a wrong part to be removed is selected, and requires an
input of a password. Ask the technical support division about the appropriateness of the
operation, and input the password after getting an approval of executing the operation.

INST03-10-160
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-170

(4) < Confirmation of amount of cache battery charge >

• When there is PCB whose amount of charge of the Cache battery is less than 50%:
“A battery whose charge capacity is less
than 50% is in the system. If there is a
battery problem on the battery, replace
it. If there is no battery problem on the
battery, wait the operation until the
charge capacity of the battery becomes
50% or more (maximum 135 min.). Do
you want to stop this process?”

When [Yes] is selected (CL), returned to INST03-10-110 Step (2).

When [No] is selected (CL), go to Step (2)

• When there is no PCB whose amount of charge of the Cache battery is less than 50%:
Go to Step 4.

(5) <Input password>

Enter the password and select (CL) [OK].

CAUTION
This is a special (exceptional) operation that can cause a serious failure such as a
system down or a data loss if a wrong part to be removed is selected, and requires an
input of a password. Ask the technical support division about the appropriateness of the
operation, and input the password after getting an approval of executing the operation.

INST03-10-170
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-180

4. Backup Module on the Cluster 1.

4-1 Start installation
Select (CL) [Yes] in response to “After you
select [Yes], you cannot cancel this operation.
Are you sure you want to continue this
operation? (Note) Do not insert the
components for upgrading the system at this
time.”.

When [No] is selected (CL), returns to

INST03-10-110 Step (2).

4-2 Check shut down LED

(1)
Select (CL)
* [Yes] if LED is on
* [No] if LED is off
in response to “Is the LED of the target
PCB(CACHE-nnn) lit?”.

(Eg. CACHE-1CA)

If [No] is selected:
Select (CL) [OK] after response to
“Check the location of the target
PCB(s)(CACHE-nnn), then pull out the
PCB(s) without considering the status of
LED.”.
Go to Step (2).
(Eg. CACHE-1CA)

INST03-10-180
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-190

(2) Check that the Shut Down LED on the CM PCB is lit.

2 2 1 1 2 2 1 1
C C C C C C C C
D C C D B A A B

Front View DKC-1 Front View of DKC-0

Shut Down LED

(Red)

PS Failure LED
(Amber)

CM PCB

Fig. 3.10-8 Location of the Shut Down LED

Table 3.10-3 Location of the CM PCB

Cluster Box Slot No. Location No. Remarks
1 DKC-0 1CA CACHE-1CA
1CB CACHE-1CB
DKC-1 1CC CACHE-1CC
1CD CACHE-1CD

INST03-10-190
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-200

4-3 Backup Module procedure

Perform an appropriate Backup Module process depending on cache capacity.
When replacement is required, go to Step 4-4.
When addition is required, go to Step 4-5.
When addition/replacement are required, go to Step 5.

4-4 Replace Backup Module (Cluster 1)

(1) <Confirmation of Backup Module replacement>
A message, “Replace the BKM(CFM),
and then select [OK]. BKM-nnn(CFM) :
BKMS(BM256) -> BKML(BM512)” is
displayed.

(Eg. BKM-1BB)

INST03-10-200
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-210

(2) Replace the BKM on the cluster 1.

(2)-1 Check that the Shut Down LED on the BKM is lit.
2BD 2BC 1BC 1BD 2BB 2BA 1BA 1BB

Front View of DKC-1 Front View of DKC-0

Shut Down LED (Red)

Front View of BKM

Fig. 3.10-9 Location of Shut Down LED

(2)-2 If the cables are attached to the BKMs, check that the screws to secure the BKMs are
tightened.
If the cables are not attached to the BKMs, go to Step (2)-4.
NOTE: If the screw is loose, the BKM may be extracted when the cables or the locking
clamp is moved.
(2)-3 Open the four locking clamps and move all the cables to where they cannot obstruct
insertion of the BKM.
BKM Screw Cable

Front View of
DKC
Locking Clamp
Fig. 3.10-10 Moving Cables
INST03-10-210
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-220

(2)-4 Loosen the screw and remove the BKM from the DKC.

Main Edge Connector

PCB
NOTICE: When removing the PCB, hold the top and bottom of
the PCB with both hands, and pull it out straight not
to contact the neighboring PCB.

DKC

BKM

Screw
Lever

Fig. 3.10-11 Removal of BKM

INST03-10-220
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-230

(2)-5 Replace the parts.

(2)-5-1 When you need to install Cache Backup Module Kit (DKC-F810I-BKML) and Cache
Flash Memory (DKC-F810I-BMM256) at the same time, replace the BKM and CFM.
When you do not need to install DKC-F810I-BKML and DKC-F810I-BMM256 at the
same time, go to the Step (2)-5-2.

a. Remove the screw of the option BKM and remove the cover.

Screw
Cover

BKM

Fig. 3.10-12 Removal of Cover

b. Install the option CFM to the BKM and tighten it with the two screws.
c. Attach the cover to the BKM and tighten it with the screw.

CFM

Screw

BKM

Screw

Fig. 3.10-13 Attachment of CFM

INST03-10-230
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-240

(2)-5-2 When you need to install only Cache Backup Module Kit (DKC-F810I-BKML),
replace the BKM.
When you do not need to install only DKC-F810I-BKML, go to the Step (2)-5-3.

a. Remove the screw of the removed BKM and remove the cover.

Screw
Cover

BKM

Fig. 3.10-14 Removal of Cover

b. Remove the two screws and detach the CFM.

c. Remove the screw of the option BKM and remove the cover.
d. Install the CFM to the option BKM and tighten it with the two screws.
e. Attach the cover to the BKM and tighten it with the screw.

CFM

Screw

BKM

Screw

Fig. 3.10-15 Movement of CFM

INST03-10-240
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-250

(2)-5-3 When you need to install only Cache Flash Memory (DKC-F810I-BMM256), replace
the CFM.
When you do not need to install only DKC-F810I-BMM256, go to the Step (2)-6.

a. Remove the screw of the removed BKM and remove the cover.

Screw
Cover

BKM

Fig. 3.10-16 Removal of Cover

b. Remove the two screws and detach the CFM.

c. Install the option CFM to the BKM and tighten it with the two screws.
d. Attach the cover to the BKM and tighten it with the screw.

CFM

Screw

BKM

Screw

Fig. 3.10-17 Replacement of CFM

INST03-10-250
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-260

(2)-6 Install the BKM to the DKC and tighten it with the screw.
(2)-7 If the cables were moved aside in Step (2)-3, put them back in place.

Main Edge Connector

PCB NOTICE: • Check that the main edge connector of the PCB has
no deformation, damage or sticking of dust before
installing the PCB. (See INST03-01-80)
• When installing the PCB, hold the top and bottom of
the PCB with both hands, and insert it straight not to
contact the neighboring PCB.

DKC

BKM

Screw
Lever

Fig. 3.10-18 Installation of BKM

INST03-10-260
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-270

(3)
When a message, “Replace the
BKM(CFM), and then select [OK].
BKM-nnn(CFM) : BKMS(BM256) ->
BKML(BM512” is displayed, select (CL)
the [OK] button.

(Eg. BKM-1BB)

4-5 Add Backup Module (Cluster 1)

(1) <Confirmation of Backup Module addition>
A message, “Insert the BKM-nnn, and
then select [OK].” is displayed.

(Eg. BKM-1BB)

INST03-10-270
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-280

(2) Install the BKM on the cluster 1.

(2)-1 Remove the screw of the option BKM and remove the cover.

Screw
Cover

BKM

Fig. 3.10-19 Removal of Cover

(2)-2 Install the option CFM to the BKM and tighten it with the two screws.
(2)-3 Attach the cover to the BKM and tighten it with the screw.

CFM

Screw

BKM

Screw

Fig. 3.10-20 Attachment of CFM

INST03-10-280
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-290

(2)-4 If the cables are attached to the BKMs, check that the screws to secure the BKMs are
tightened.
If the cables are not attached to the BKMs, go to Step (2)-6.
NOTE: If the screw is loose, the BKM may be extracted when the cables or the locking
clamp is moved.
(2)-5 Open the four locking clamps and move all the cables to where they cannot obstruct
insertion of the BKM.

BKM Screw Cable

Front View of
DKC
Locking Clamp
Fig. 3.10-21 Moving Cables

INST03-10-290
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-300

(2)-6 Loosen the screw and remove the dummy plate.

(2)-7 Install the BKM to the DKC and tighten the screw.
(2)-8 If the cables were moved aside in Step (2)-5, put them back in place.

Main Edge Connector

PCB NOTICE: • Check that the main edge connector of the PCB has
no deformation, damage or sticking of dust before
installing the PCB. (See INST03-01-80)
• When installing the PCB, hold the top and bottom of
the PCB with both hands, and insert it straight not to
contact the neighboring PCB.

2BD 2BC 1BC 1BD 2BB 2BA 1BA 1BB

Front View of DKC-1 Front View of DKC-0

DKC

BKM

Screw
Lever

Screw

Dummy Plate

Fig. 3.10-22 Installation of BKM

INST03-10-300
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-310

(3)
When a message, “Insert the BKM-nnn,
and then select [OK].” is displayed, select
(CL) the [OK] button.

(Eg. BKM-1BB)

INST03-10-310
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-320

5. SVP pre procedure (Cluster 1).

(1)
“The Cache Memory PCB is being blocked...”
“Lighting LED of the PCB...” is displayed.

(2) <Perform cache hardware installation>

At this point refrain from pressing the
[OK] button.
When “Replace or insert the Cache
Memory PCB(s)(Memory) of cluster-1.
When completed, please press OK.” is
displayed, install hardware components
according to the cache hardware
installation procedure.

Make sure of the installation location and

size of the module to be added and insert
the correct module in the correct location.
(The Shared Memory capacity may be
changed at the same time, depending on the set Cache Memory capacity.)

INST03-10-320
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-330

6. Install the Cache Memory on the cluster 1.

NOTICE: Be sure to wear your wrist strap and attach to ground prior to performing the
following work. This will ensure that the IC and LSI on the PCB are protected
from static electricity.

6-1 Remove the PCB.

a. If the cables are connected to the CM PCB, disconnect the cables after checking “3.1.7
Notes when connecting and disconnecting MFC cable” (INST03-01-190).
If the cables are not connected to the CM PCB, go to Step b.

INST03-10-330
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-340

b. Remove the two screws and remove the CM PCB.

NOTE: When removing the CM PCB, be careful not to pull cables.

Main Edge Connector

PCB
NOTICE: When removing the PCB, hold the top and bottom of
the PCB with both hands, and pull it out straight not to
contact the neighboring PCB.

DKC

CM PCB

Screw

Lever

Cable

Lever Screw

Fig. 3.10-23 Removal of PCB

INST03-10-340
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-350

6-2 Insert the CM Modules.

a. Loosen the screw and remove the cover.

Screw

CM PCB

Cover

Fig. 3.10-24 Removal of Cover

INST03-10-350
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-360

b. Remove the dust covers that match the required Cache Memory capacity referring to Fig.
3.10-25, Fig. 3.10-26, Fig. 3.10-27, Table 3.10-4 through Table 3.10-9.
c. Insert the CM Modules that match the required Cache Memory capacity.
d. Attach the cover and fasten the screw. (Refer to Fig. 3.10-24.)

CM Module Location of DKC-0

Cluster 1 (CACHE-1CA/1CB)

Removal of Dust Cover

A CM PCB Dust Cover
(WP840-A)
Socket
PCB
Viewed from A

CACHE-1CA (Basic) CACHE-1CB (Option 1)

CM1P: *2 CM1P: *10

CM5P: *6 CM5P: *14
CM3P: *4 CM3P: *12
CM7P: *8 CM7P: *16

CM6P: *7 CM6P: *15

CM2P: *3 CM2P: *11
CM4P: *5 CM4P: *13
CM0P: *1 CM0P: *9

NOTE1: The cache memory module location *1 through *16 correspond to the CM Location
listed in Table 3.10-4 through Table 3.10-9.
Fig. 3.10-25 Inserting Location of the CM Module

INST03-10-360
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-370

CM Module Location of DKC-1

Cluster 1 (CACHE-1CC/1CD)

Removal of Dust Cover

A CM PCB Dust Cover
(WP840-A) Socket
PCB
Viewed from A

CACHE-1CC (Option 2) CACHE-1CD (Option 3)

CM1P: *18 CM1P: *26

CM5P: *22 CM5P: *30
CM3P: *20 CM3P: *28
CM7P: *24 CM7P: *32

CM6P: *23 CM6P: *31

CM2P: *19 CM2P: *27
CM4P: *21 CM4P: *29
CM0P: *17 CM0P: *25

NOTE1: The cache memory module location *17 through *32 correspond to the CM
Location listed in Table 3.10-4 through Table 3.10-9.
Fig. 3.10-26 Inserting Location of the CM Module

INST03-10-370
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-380


Memory Module 
 Lever
Cut

Socket

Projection
inside the slot

Installation
 Position the cut of the memory module with the projection inside the slot,
and place the memory module on the socket.
 Hold both ends of the memory module by the fingers, and fit it into the socket.
 Make sure that the lever is firmly fitted in the memory module.

NOTICE: Do not put intense pressure on the CM Module to the extent that the PCB
greatly bends after the CM Module is secured with the levers in installation
procedure of the CM Module. The PCB may be damaged when intense
pressure is applied.

Memory Module Appearance

There are two types of memory modules. One has a heat spreader and the other has no heat spreaders.
Both memory modules can be used because they are compatible with each other.

Memory Module Memory Module

(with Heat Spreader) (without Heat Spreader)

Heat Spreader

Fig. 3.10-27 Insertion of Memory Module

INST03-10-380
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-390

Table 3.10-4 Cache memory capacity and number of necessary options 

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM16G CPEX BKMS/ BMM128/
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD BKML BMM256
1 32GB *1 — — — 2 0 1 2
2 64GB *1,*2 — — — 4 0 1 2
3 96GB *1-*3 — — — 6 0 1 2
4 128GB *1-*4 — — — 8 0 1 2
5 160GB *1-*5 — — — 10 0 1 2
6 192GB *1-*7 — — — 12 0 1 2
7 224GB *1-*8 — — — 14 0 1 2
8 256GB *1-*8 — — — 16 0 1 2
9 288GB *1-*8 *9 — — 18 1 2 4
10 320GB *1-*8 *9,*10 — — 20 1 2 4
11 356GB *1-*8 *9-*11 — — 22 1 2 4
12 384GB *1-*8 *9-*12 — — 24 1 2 4
13 416GB *1-*8 *9-*13 — — 26 1 2 4
14 448GB *1-*8 *9-*14 — — 28 1 2 4
15 480GB *1-*8 *9-*15 — — 30 1 2 4
16 512GB *1-*8 *9-*16 — — 32 1 2 4
17 576GB *1-*8 *9-*16 *17 *25 36 2 4 8
18 608GB *1-*8 *9-*16 *17,*18 *25 38 2 4 8
19 640GB *1-*8 *9-*16 *17,*18 *25,*26 40 2 4 8
20 672GB *1-*8 *9-*16 *17-*19 *25,*26 42 2 4 8
21 704GB *1-*8 *9-*16 *17-*19 *25-*27 44 2 4 8
22 736GB *1-*8 *9-*16 *17-*20 *25-*27 46 2 4 8
23 768GB *1-*8 *9-*16 *17-*20 *25-*28 48 2 4 8
24 800GB *1-*8 *9-*16 *17-*21 *25-*28 50 2 4 8
25 832GB *1-*8 *9-*16 *17-*21 *25-*29 52 2 4 8
26 864GB *1-*8 *9-*16 *17-*22 *25-*29 54 2 4 8
27 896GB *1-*8 *9-*16 *17-*22 *25-*30 56 2 4 8
28 928GB *1-*8 *9-*16 *17-*23 *25-*30 58 2 4 8
29 960GB *1-*8 *9-*16 *17-*23 *25-*31 60 2 4 8
30 992GB *1-*8 *9-*16 *17-*24 *25-*31 62 2 4 8
31 1024GB *1-*8 *9-*16 *17-*24 *25-*32 64 2 4 8

NOTE 1: The above numbers (*1 through *32) represent the CM Module locations shown in
Fig. 3.10-25, Fig. 3.10-26, Fig. 3.10-47 or Fig. 3.10-48.

INST03-10-390
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-400

Table 3.10-5 Cache memory capacity and number of necessary options 

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM32G CPEX BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 128 256
1 64GB *1 — — — 2 0 1 0 2 0
2 128GB *1,*2 — — — 4 0 1 0 2 0
3 192GB *1-*3 — — — 6 0 1 0 2 0
4 256GB *1-*4 — — — 8 0 1 0 2 0
5 320GB *1-*5 — — — 10 0 0 1 0 2
6 384GB *1-*7 — — — 12 0 0 1 0 2
7 448GB *1-*8 — — — 14 0 0 1 0 2
8 512GB *1-*8 — — — 16 0 0 1 0 2
9 576GB *1-*8 *9 — — 18 1 1 1 2 2
10 640GB *1-*8 *9,*10 — — 20 1 1 1 2 2
11 704GB *1-*8 *9-*11 — — 22 1 1 1 2 2
12 768GB *1-*8 *9-*12 — — 24 1 1 1 2 2
13 832GB *1-*8 *9-*13 — — 26 1 0 2 0 4
14 896GB *1-*8 *9-*14 — — 28 1 0 2 0 4
15 960GB *1-*8 *9-*15 — — 30 1 0 2 0 4
16 1024GB *1-*8 *9-*16 — — 32 1 0 2 0 4
17 1152GB *1-*8 *9-*16 *17 *25 36 2 2 2 4 4
18 1216GB *1-*8 *9-*16 *17,*18 *25 38 2 2 2 4 4
19 1280GB *1-*8 *9-*16 *17,*18 *25,*26 40 2 2 2 4 4
20 1344GB *1-*8 *9-*16 *17-*19 *25,*26 42 2 2 2 4 4
21 1408GB *1-*8 *9-*16 *17-*19 *25-*27 44 2 2 2 4 4
22 1472GB *1-*8 *9-*16 *17-*20 *25-*27 46 2 2 2 4 4
23 1536GB *1-*8 *9-*16 *17-*20 *25-*28 48 2 2 2 4 4
24 1600GB *1-*8 *9-*16 *17-*21 *25-*28 50 2 1 3 2 6
25 1664GB *1-*8 *9-*16 *17-*21 *25-*29 52 2 0 4 0 8
26 1728GB *1-*8 *9-*16 *17-*22 *25-*29 54 2 0 4 0 8
27 1792GB *1-*8 *9-*16 *17-*22 *25-*30 56 2 0 4 0 8
28 1856GB *1-*8 *9-*16 *17-*23 *25-*30 58 2 0 4 0 8
29 1920GB *1-*8 *9-*16 *17-*23 *25-*31 60 2 0 4 0 8
30 1984GB *1-*8 *9-*16 *17-*24 *25-*31 62 2 0 4 0 8
31 2048GB *1-*8 *9-*16 *17-*24 *25-*32 64 2 0 4 0 8

NOTE 1: The above numbers (*1 through *32) represent the CM Module locations shown in
Fig. 3.10-25, Fig. 3.10-26, Fig. 3.10-47 or Fig. 3.10-48.

INST03-10-400
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-410

Table 3.10-6 Cache memory capacity and number of necessary options 

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-
Capacity CPEX-0 CPEX-1 CM16G CPEX BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 128 256
1 64GB *1 *9 4 1 2 0 4 0
2 96GB *1,*2 *9 6 1 2 0 4 0
3 128GB *1,*2 *9,*10 8 1 2 0 4 0
4 128GB *1-*3 *9 8 1 2 0 4 0
5 160GB *1-*3 *9,*10 10 1 2 0 4 0
6 160GB *1-*4 *9 10 1 2 0 4 0
7 192GB *1-*3 *9-*11 12 1 2 0 4 0
8 192GB *1-*4 *9,*10 12 1 2 0 4 0
9 192GB *1-*5 *9 12 1 2 0 4 0
10 224GB *1-*4 *9-*11 14 1 2 0 4 0
11 224GB *1-*5 *9,*10 14 1 2 0 4 0
12 224GB *1-*6 *9 14 1 2 0 4 0
13 256GB *1-*4 *9-*12 16 1 2 0 4 0
14 256GB *1-*5 *9-*11 16 1 2 0 4 0
15 256GB *1-*6 *9,*10 16 1 2 0 4 0
16 256GB *1-*7 *9 16 1 2 0 4 0
17 288GB *1-*5 *9-*12 18 1 2 0 4 0
18 288GB *1-*6 *9-*11 18 1 2 0 4 0
19 288GB *1-*7 *9,*10 18 1 2 0 4 0
20 288GB *1-*8 *9 18 1 2 0 4 0
21 320GB *1-*5 *9-*13 20 1 2 0 4 0
22 320GB *1-*6 *9-*12 20 1 2 0 4 0
23 320GB *1-*7 *9-*11 20 1 2 0 4 0
24 320GB *1-*8 *9,*10 20 1 2 0 4 0
25 352GB *1-*6 *9-*13 22 1 2 0 4 0
26 352GB *1-*7 *9-*12 22 1 2 0 4 0
27 352GB *1-*8 *9-*11 22 1 2 0 4 0
28 384GB *1-*6 *9-*14 24 1 2 0 4 0
29 384GB *1-*7 *9-*13 24 1 2 0 4 0
30 384GB *1-*8 *9-*12 24 1 2 0 4 0
31 416GB *1-*7 *9-*14 26 1 2 0 4 0
32 416GB *1-*8 *9-*13 26 1 2 0 4 0
33 448GB *1-*7 *9-*15 28 1 2 0 4 0
34 448GB *1-*8 *9-*14 28 1 2 0 4 0
35 480GB *1-*8 *9-*15 30 1 2 0 4 0
36 512GB *1-*8 *9-*16 32 1 2 0 4 0

NOTE 1: The above numbers (*1 through *16) represent the CM Module locations shown in
Fig. 3.10-25, Fig. 3.10-26, Fig. 3.10-47 or Fig. 3.10-48.
NOTE 2: The required SM capacity shown in Table 6.1-1 (INST06-10) must be installed in
CPEX-0.
INST03-10-410
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-420

Table 3.10-7 Cache memory capacity and number of necessary options 

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-
Capacity CPEX-0 CPEX-1 CM32G CPEX BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 128 256
1 128GB *1 *9 4 1 2 0 4 0
2 192GB *1,*2 *9 6 1 2 0 4 0
3 256GB *1,*2 *9,*10 8 1 2 0 4 0
4 256GB *1-*3 *9 8 1 2 0 4 0
5 320GB *1-*3 *9,*10 10 1 2 0 4 0
6 320GB *1-*4 *9 10 1 2 0 4 0
7 384GB *1-*3 *9-*11 12 1 2 0 4 0
8 384GB *1-*4 *9,*10 12 1 2 0 4 0
9 384GB *1-*5 *9 12 1 1 1 2 2
10 448GB *1-*4 *9-*11 14 1 2 0 4 0
11 448GB *1-*5 *9,*10 14 1 1 1 2 2
12 448GB *1-*6 *9 14 1 1 1 2 2
13 512GB *1-*4 *9-*12 16 1 2 0 4 0
14 512GB *1-*5 *9-*11 16 1 1 1 2 2
15 512GB *1-*6 *9,*10 16 1 1 1 2 2
16 512GB *1-*7 *9 16 1 1 1 2 2
17 576GB *1-*5 *9-*12 18 1 1 1 2 2
18 576GB *1-*6 *9-*11 18 1 1 1 2 2
19 576GB *1-*7 *9,*10 18 1 1 1 2 2
20 576GB *1-*8 *9 18 1 1 1 2 2
21 640GB *1-*5 *9-*13 20 1 0 2 0 4
22 640GB *1-*6 *9-*12 20 1 1 1 2 2
23 640GB *1-*7 *9-*11 20 1 1 1 2 2
24 640GB *1-*8 *9,*10 20 1 1 1 2 2
25 704GB *1-*6 *9-*13 22 1 0 2 0 4
26 704GB *1-*7 *9-*12 22 1 1 1 2 2
27 704GB *1-*8 *9-*11 22 1 1 1 2 2
28 768GB *1-*6 *9-*14 24 1 0 2 0 4
29 768GB *1-*7 *9-*13 24 1 0 2 0 4
30 768GB *1-*8 *9-*12 24 1 1 1 2 2
31 832GB *1-*7 *9-*14 26 1 0 2 0 4
32 832GB *1-*8 *9-*13 26 1 0 2 0 4
33 896GB *1-*7 *9-*15 28 1 0 2 0 4
34 896GB *1-*8 *9-*14 28 1 0 2 0 4
35 960GB *1-*8 *9-*15 30 1 0 2 0 4
36 1024GB *1-*8 *9-*16 32 1 0 2 0 4

NOTE 1: The above numbers (*1 through *16) represent the CM Module locations shown in
Fig. 3.10-25, Fig. 3.10-26, Fig. 3.10-47 or Fig. 3.10-48.
NOTE 2: The required SM capacity shown in Table 6.1-1 (INST06-10) must be installed in
CPEX-0.
INST03-10-420
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-430

Table 3.10-8 Cache memory capacity and number of necessary options 

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 16G 128 256
1 64 *1 — *17 — 4 0 1 0 2 — 4 —
2 96 *1,*2 — *17 — 6 0 1 0 2 — 4 —
3 128 *1 *9 *17 *25 8 2 1 1 4 — 8 —
4 128 *1,*2 — *17,*18 — 8 0 1 0 2 — 4 —
5 128 *1-*3 — *17 — 8 0 1 0 2 — 4 —
6 160 *1,*2 *9 *17 *25 10 2 1 1 4 — 8 —
7 160 *1-*3 — *17,*18 — 10 0 1 0 2 — 4 —
8 160 *1-*4 — *17 — 10 0 1 0 2 — 4 —
9 192 *1,*2 *9 *17,*18 *25 12 2 1 1 4 — 8 —
10 192 *1,*2 *9,*10 *17 *25 12 2 1 1 4 — 8 —
11 192 *1-*3 — *17-*19 — 12 0 1 0 2 — 4 —
12 192 *1-*3 *9 *17 *25 12 2 1 1 4 — 8 —
13 192 *1-*4 — *17,*18 — 12 0 1 0 2 — 4 —
14 192 *1-*5 — *17 — 12 0 1 0 2 — 4 —
15 224 *1,*2 *9,*10 *17,*18 *25 14 2 1 1 4 — 8 —
16 224 *1-*3 *9,*10 *17 *25 14 2 1 1 4 — 8 —
17 224 *1-*4 *9 *17 *25 14 2 1 1 4 — 8 —
18 224 *1-*5 — *17,*18 — 14 0 1 0 2 — 4 —
19 224 *1-*6 — *17 — 14 0 1 0 2 — 4 —
20 256 *1,*2 *9,*10 *17,*18 *25,*26 16 2 1 1 4 — 8 —
21 256 *1-*3 *9 *17-*19 *25 16 2 1 1 4 — 8 —
22 256 *1-*3 *9,*10 *17,*18 *25 16 2 1 1 4 — 8 —
23 256 *1-*3 *9-*11 *17 *25 16 2 1 1 4 — 8 —
24 256 *1-*4 — *17-*20 — 16 0 1 0 2 — 4 —
25 256 *1-*4 *9,*10 *17 *25 16 2 1 1 4 — 8 —
26 256 *1-*5 — *17-*19 — 16 0 1 0 2 — 4 —
27 256 *1-*5 *9 *17 *25 16 2 1 1 4 — 8 —
28 256 *1-*6 — *17,*18 — 16 0 1 0 2 — 4 —
29 256 *1-*7 — *17 — 16 0 1 0 2 — 4 —
30 288 *1-*3 *9,*10 *17,*18 *25,*26 18 2 1 1 4 — 8 —
31 288 *1-*3 *9,*10 *17-*19 *25 18 2 1 1 4 — 8 —
32 288 *1-*3 *9-*11 *17,*18 *25 18 2 1 1 4 — 8 —
33 288 *1-*4 *9,*10 *17,*18 *25 18 2 1 1 4 — 8 —
34 288 *1-*4 *9-*11 *17 *25 18 2 1 1 4 — 8 —
35 288 *1-*5 — *17-*20 — 18 0 1 0 2 — 4 —
(To be continued)

INST03-10-430
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-440

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 16G 128 256
36 288 *1-*5 *9,*10 *17 *25 18 2 1 1 4 — 8 —
37 288 *1-*6 — *17-*19 — 18 0 1 0 2 — 4 —
38 288 *1-*6 *9 *17 *25 18 2 1 1 4 — 8 —
39 288 *1-*7 — *17,*18 — 18 0 1 0 2 — 4 —
40 288 *1-*8 — *17 — 18 0 1 0 2 — 4 —
41 320 *1-*3 *9,*10 *17-*19 *25,*26 20 2 1 1 4 — 8 —
42 320 *1-*3 *9-*11 *17,*18 *25,*26 20 2 1 1 4 — 8 —
43 320 *1-*3 *9-*11 *17-*19 *25 20 2 1 1 4 — 8 —
44 320 *1-*4 *9 *17-*20 *25 20 2 1 1 4 — 8 —
45 320 *1-*4 *9,*10 *17,*18 *25,*26 20 2 1 1 4 — 8 —
46 320 *1-*4 *9-*11 *17,*18 *25 20 2 1 1 4 — 8 —
47 320 *1-*4 *9-*12 *17 *25 20 2 1 1 4 — 8 —
48 320 *1-*5 — *17-*21 — 20 0 1 0 2 — 4 —
49 320 *1-*5 *9,*10 *17,*18 *25 20 2 1 1 4 — 8 —
50 320 *1-*5 *9-*11 *17 *25 20 2 1 1 4 — 8 —
51 320 *1-*6 — *17-*20 — 20 0 1 0 2 — 4 —
52 320 *1-*6 *9,*10 *17 *25 20 2 1 1 4 — 8 —
53 320 *1-*7 — *17-*19 — 20 0 1 0 2 — 4 —
54 320 *1-*7 *9 *17 *25 20 2 1 1 4 — 8 —
55 320 *1-*8 — *17,*18 — 20 0 1 0 2 — 4 —
56 352 *1-*3 *9-*11 *17-*19 *25,*26 22 2 1 1 4 — 8 —
57 352 *1-*4 *9,*10 *17-*20 *25 22 2 1 1 4 — 8 —
58 352 *1-*4 *9-*11 *17,*18 *25,*26 22 2 1 1 4 — 8 —
59 352 *1-*4 *9-*11 *17-*19 *25 22 2 1 1 4 — 8 —
60 352 *1-*4 *9-*12 *17,*18 *25 22 2 1 1 4 — 8 —
61 352 *1-*5 *9,*10 *17,*18 *25,*26 22 2 1 1 4 — 8 —
62 352 *1-*5 *9-*11 *17,*18 *25 22 2 1 1 4 — 8 —
63 352 *1-*5 *9-*12 *17 *25 22 2 1 1 4 — 8 —
64 352 *1-*6 — *17-*21 — 22 0 1 0 2 — 4 —
65 352 *1-*6 *9,*10 *17,*18 *25 22 2 1 1 4 — 8 —
66 352 *1-*6 *9-*11 *17 *25 22 2 1 1 4 — 8 —
67 352 *1-*7 — *17-*20 — 22 0 1 0 2 — 4 —
68 352 *1-*7 *9,*10 *17 *25 22 2 1 1 4 — 8 —
69 352 *1-*8 — *17-*19 — 22 0 1 0 2 — 4 —
70 352 *1-*8 *9 *17 *25 22 2 1 1 4 — 8 —
(To be continued)

INST03-10-440
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-450

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 16G 128 256
71 384 *1-*3 *9-*11 *17-*19 *25-*27 24 2 1 1 4 — 8 —
72 384 *1-*4 *9,*10 *17-*20 *25,*26 24 2 1 1 4 — 8 —
73 384 *1-*4 *9-*11 *17-*19 *25,*26 24 2 1 1 4 — 8 —
74 384 *1-*4 *9-*11 *17-*20 *25 24 2 1 1 4 — 8 —
75 384 *1-*4 *9-*12 *17,*18 *25,*26 24 2 1 1 4 — 8 —
76 384 *1-*4 *9-*12 *17-*19 *25 24 2 1 1 4 — 8 —
77 384 *1-*5 32 *17-*21 *25 24 2 1 1 4 — 8 —
78 384 *1-*5 *9-*11 *17,*18 *25,*26 24 2 1 1 4 — 8 —
79 384 *1-*5 *9-*11 *17-*19 *25 24 2 1 1 4 — 8 —
80 384 *1-*5 *9-*12 *17,*18 *25 24 2 1 1 4 — 8 —
81 384 *1-*5 *9-*13 *17 *25 24 2 1 1 4 — 8 —
82 384 *1-*6 — *17-*22 — 24 0 1 0 2 — 4 —
83 384 *1-*6 *9,*10 *17,*18 *25,*26 24 2 1 1 4 — 8 —
84 384 *1-*6 *9-*11 *17,*18 *25 24 2 1 1 4 — 8 —
85 384 *1-*6 *9-*12 *17 *25 24 2 1 1 4 — 8 —
86 384 *1-*7 — *17-*21 — 24 0 1 0 2 — 4 —
87 384 *1-*7 *9,*10 *17,*18 *25 24 2 1 1 4 — 8 —
88 384 *1-*7 *9-*11 *17 *25 24 2 1 1 4 — 8 —
89 384 *1-*8 — *17-*20 — 24 0 1 0 2 — 4 —
90 384 *1-*8 *9,*10 *17 *25 24 2 1 1 4 — 8 —
91 416 *1-*4 *9-*11 *17-*19 *25-*27 26 2 1 1 4 — 8 —
92 416 *1-*4 *9-*11 *17-*20 *25,*26 26 2 1 1 4 — 8 —
93 416 *1-*4 *9-*12 *17-*19 *25,*26 26 2 1 1 4 — 8 —
94 416 *1-*4 *9-*12 *17-*20 *25 26 2 1 1 4 — 8 —
95 416 *1-*5 *9,*10 *17-*21 *25 26 2 1 1 4 — 8 —
96 416 *1-*5 *9-*11 *17-*19 *25,*26 26 2 1 1 4 — 8 —
97 416 *1-*5 *9-*12 *17,*18 *25,*26 26 2 1 1 4 — 8 —
98 416 *1-*5 *9-*12 *17-*19 *25 26 2 1 1 4 — 8 —
99 416 *1-*5 *9-*13 *17,*18 *25 26 2 1 1 4 — 8 —
100 416 *1-*6 *9-*11 *17,*18 *25,*26 26 2 1 1 4 — 8 —
101 416 *1-*6 *9-*11 *17-*19 *25 26 2 1 1 4 — 8 —
102 416 *1-*6 *9-*12 *17,*18 *25 26 2 1 1 4 — 8 —
103 416 *1-*6 *9-*13 *17 *25 26 2 1 1 4 — 8 —
104 416 *1-*7 — *17-*22 — 26 0 1 0 2 — 4 —
105 416 *1-*7 *9,*10 *17,*18 *25,*26 26 2 1 1 4 — 8 —
(To be continued)

INST03-10-450
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-460

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 16G 128 256
106 416 *1-*7 *9-*11 *17,*18 *25 26 2 1 1 4 — 8 —
107 416 *1-*7 *9-*12 *17 *25 26 2 1 1 4 — 8 —
108 416 *1-*8 — *17-*21 — 26 0 1 0 2 — 4 —
109 416 *1-*8 *9-*11 *17 *25 26 2 1 1 4 — 8 —
110 448 *1-*4 *9-*11 *17-*20 *25-*27 28 2 1 1 4 — 8 —
111 448 *1-*4 *9-*12 *17-*19 *25-*27 28 2 1 1 4 — 8 —
112 448 *1-*4 *9-*12 *17-*20 *25,*26 28 2 1 1 4 — 8 —
113 448 *1-*5 *9,*10 *17-*21 *25,*26 28 2 1 1 4 — 8 —
114 448 *1-*5 *9-*11 *17-*19 *25-*27 28 2 1 1 4 — 8 —
115 448 *1-*5 *9-*11 *17-*21 *25 28 2 1 1 4 — 8 —
116 448 *1-*5 *9-*12 *17-*19 *25,*26 28 2 1 1 4 — 8 —
117 448 *1-*5 *9-*12 *17-*20 *25 28 2 1 1 4 — 8 —
118 448 *1-*5 *9-*13 *17,*18 *25,*26 28 2 1 1 4 — 8 —
119 448 *1-*5 *9-*13 *17-*19 *25 28 2 1 1 4 — 8 —
120 448 *1-*6 *9 *17-*22 *25 28 2 1 1 4 — 8 —
121 448 *1-*6 *9-*11 *17-*19 *25,*26 28 2 1 1 4 — 8 —
122 448 *1-*6 *9-*12 *17,*18 *25,*26 28 2 1 1 4 — 8 —
123 448 *1-*6 *9-*12 *17-*19 *25 28 2 1 1 4 — 8 —
124 448 *1-*6 *9-*13 *17,*18 *25 28 2 1 1 4 — 8 —
125 448 *1-*6 *9-*14 *17 *25 28 2 1 1 4 — 8 —
126 448 *1-*7 — 224 — 28 0 1 0 2 — 4 —
127 448 *1-*7 *9-*11 *17,*18 *25,*26 28 2 1 1 4 — 8 —
128 448 *1-*7 *9-*11 *17-*19 *25 28 2 1 1 4 — 8 —
129 448 *1-*7 *9-*12 *17,*18 *25 28 2 1 1 4 — 8 —
130 448 *1-*7 *9-*13 *17 *25 28 2 1 1 4 — 8 —
131 448 *1-*8 — *17-*22 — 28 0 1 0 2 — 4 —
132 448 *1-*8 *9-*12 *17 *25 28 2 1 1 4 — 8 —
133 480 *1-*4 *9-*12 *17-*20 *25-*27 30 2 1 1 4 — 8 —
134 480 *1-*5 *9-*11 *17-*21 *25,*26 30 2 1 1 4 — 8 —
135 480 *1-*5 *9-*12 *17-*19 *25-*27 30 2 1 1 4 — 8 —
136 480 *1-*5 *9-*12 *17-*20 *25,*26 30 2 1 1 4 — 8 —
137 480 *1-*5 *9-*12 *17-*21 *25 30 2 1 1 4 — 8 —
138 480 *1-*5 *9-*13 *17-*19 *25,*26 30 2 1 1 4 — 8 —
139 480 *1-*5 *9-*13 *17-*20 *25 30 2 1 1 4 — 8 —
140 480 *1-*6 *9,*10 *17-*22 *25 30 2 1 1 4 — 8 —
(To be continued)

INST03-10-460
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-470

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 16G 128 256
141 480 *1-*6 *9-*11 *17-*19 *25-*27 30 2 1 1 4 — 8 —
142 480 *1-*6 *9-*12 *17-*19 *25,*26 30 2 1 1 4 — 8 —
143 480 *1-*6 *9-*12 *17-*20 *25 30 2 1 1 4 — 8 —
144 480 *1-*6 *9-*13 *17,*18 *25,*26 30 2 1 1 4 — 8 —
145 480 *1-*6 *9-*13 *17-*19 *25 30 2 1 1 4 — 8 —
146 480 *1-*6 *9-*14 *17,*18 *25 30 2 1 1 4 — 8 —
147 480 *1-*7 *9-*11 *17-*19 *25,*26 30 2 1 1 4 — 8 —
148 480 *1-*7 *9-*12 *17,*18 *25,*26 30 2 1 1 4 — 8 —
149 480 *1-*7 *9-*12 *17-*19 *25 30 2 1 1 4 — 8 —
150 480 *1-*7 *9-*13 *17,*18 *25 30 2 1 1 4 — 8 —
151 480 *1-*8 — *17-*23 — 30 0 1 0 2 — 4 —
152 480 *1-*8 *9-*13 *17 *25 30 2 1 1 4 — 8 —
153 512 *1-*4 *9-*12 *17-*20 128 32 2 1 1 4 — 8 —
154 512 *1-*5 *9-*11 *17-*21 *25-*27 32 2 1 1 4 — 8 —
155 512 *1-*5 *9-*12 *17-*20 *25-*27 32 2 1 1 4 — 8 —
156 512 *1-*5 *9-*12 *17-*21 *25,*26 32 2 1 1 4 — 8 —
157 512 *1-*5 *9-*13 *17-*19 *25-*27 32 2 1 1 4 — 8 —
158 512 *1-*5 *9-*13 *17-*20 *25,*26 32 2 1 1 4 — 8 —
159 512 *1-*5 *9-*13 *17-*21 *25 32 2 1 1 4 — 8 —
160 512 *1-*6 *9,*10 *17-*22 *25,*26 32 2 1 1 4 — 8 —
161 512 *1-*6 *9-*11 *17-*22 *25 32 2 1 1 4 — 8 —
162 512 *1-*6 *9-*12 *17-*19 *25-*27 32 2 1 1 4 — 8 —
163 512 *1-*6 *9-*12 *17-*20 *25,*26 32 2 1 1 4 — 8 —
164 512 *1-*6 *9-*13 *17-*19 *25,*26 32 2 1 1 4 — 8 —
165 512 *1-*6 *9-*13 *17-*20 *25 32 2 1 1 4 — 8 —
166 512 *1-*6 *9-*14 *17,*18 *25,*26 32 2 1 1 4 — 8 —
167 512 *1-*6 *9-*14 *17-*19 *25 32 2 1 1 4 — 8 —
168 512 *1-*7 *9 *17-*23 *25 32 2 1 1 4 — 8 —
169 512 *1-*7 *9-*11 *17-*19 *25-*27 32 2 1 1 4 — 8 —
170 512 *1-*7 *9-*12 *17-*19 *25,*26 32 2 1 1 4 — 8 —
171 512 *1-*7 *9-*12 *17-*20 *25 32 2 1 1 4 — 8 —
172 512 *1-*7 *9-*13 *17,*18 *25,*26 32 2 1 1 4 — 8 —
173 512 *1-*7 *9-*13 *17-*19 *25 32 2 1 1 4 — 8 —
174 512 *1-*7 *9-*15 *17 *25 32 2 1 1 4 — 8 —
175 512 *1-*8 — *17-*24 — 32 0 1 0 2 — 4 —
(To be continued)

INST03-10-470
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-480

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 16G 128 256
176 512 *1-*8 *9-*14 *17 *25 32 2 1 1 4 — 8 —
177 544 *1-*5 *9-*12 *17-*20 *25-*28 34 2 1 1 4 — 8 —
178 544 *1-*5 *9-*12 *17-*21 *25-*27 34 2 1 1 4 — 8 —
179 544 *1-*5 *9-*13 *17-*20 *25-*27 34 2 1 1 4 — 8 —
180 544 *1-*5 *9-*13 *17-*21 *25,*26 34 2 1 1 4 — 8 —
181 544 *1-*6 *9-*11 *17-*22 *25,*26 34 2 1 1 4 — 8 —
182 544 *1-*6 *9-*12 *17-*20 *25-*27 34 2 1 1 4 — 8 —
183 544 *1-*6 *9-*12 *17-*22 *25 34 2 1 1 4 — 8 —
184 544 *1-*6 *9-*13 *17-*19 *25-*27 34 2 1 1 4 — 8 —
185 544 *1-*6 *9-*13 *17-*20 *25,*26 34 2 1 1 4 — 8 —
186 544 *1-*6 *9-*13 *17-*21 *25 34 2 1 1 4 — 8 —
187 544 *1-*6 *9-*14 *17-*19 *25,*26 34 2 1 1 4 — 8 —
188 544 *1-*6 *9-*14 *17-*20 *25 34 2 1 1 4 — 8 —
189 544 *1-*7 *9,*10 *17-*23 *25 34 2 1 1 4 — 8 —
190 544 *1-*7 *9-*12 *17-*19 *25-*27 34 2 1 1 4 — 8 —
191 544 *1-*7 *9-*12 *17-*20 *25,*26 34 2 1 1 4 — 8 —
192 544 *1-*7 *9-*13 *17-*19 *25,*26 34 2 1 1 4 — 8 —
193 544 *1-*7 *9-*13 *17-*20 *25 34 2 1 1 4 — 8 —
194 544 *1-*7 *9-*15 *17,*18 *25 34 2 1 1 4 — 8 —
195 544 *1-*8 *9-*15 *17 *25 34 2 1 1 4 — 8 —
196 576 *1-*5 *9-*12 *17-*21 *25-*28 36 2 1 1 4 — 8 —
197 576 *1-*5 *9-*13 *17-*20 *25-*28 36 2 1 1 4 — 8 —
198 576 *1-*5 *9-*13 *17-*21 *25-*27 36 2 1 1 4 — 8 —
199 576 *1-*6 *9-*11 *17-*22 *25-*27 36 2 1 1 4 — 8 —
200 576 *1-*6 *9-*12 *17-*20 *25-*28 36 2 1 1 4 — 8 —
201 576 *1-*6 *9-*12 *17-*22 *25,*26 36 2 1 1 4 — 8 —
202 576 *1-*6 *9-*13 *17-*20 *25-*27 36 2 1 1 4 — 8 —
203 576 *1-*6 *9-*13 *17-*21 *25,*26 36 2 1 1 4 — 8 —
204 576 *1-*6 *9-*13 *17-*22 *25 36 2 1 1 4 — 8 —
205 576 *1-*6 *9-*13 *17-*22 *25 36 2 1 1 4 — 8 —
206 576 *1-*6 *9-*14 *17-*19 *25-*27 36 2 1 1 4 — 8 —
207 576 *1-*6 *9-*14 *17-*20 *25,*26 36 2 1 1 4 — 8 —
208 576 *1-*6 *9-*14 *17-*21 *25 36 2 1 1 4 — 8 —
209 576 *1-*7 *9,*10 *17-*23 *25,*26 36 2 1 1 4 — 8 —
210 576 *1-*7 *9-*11 *17-*23 *25 36 2 1 1 4 — 8 —
(To be continued)

INST03-10-480
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-490

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 16G 128 256
211 576 *1-*7 *9-*12 *17-*20 *25-*27 36 2 1 1 4 — 8 —
212 576 *1-*7 *9-*13 *17-*19 *25-*27 36 2 1 1 4 — 8 —
213 576 *1-*7 *9-*13 *17-*20 *25,*26 36 2 1 1 4 — 8 —
214 576 *1-*7 *9-*13 *17-*21 *25 36 2 1 1 4 — 8 —
215 576 *1-*7 *9-*15 *17-*19 *25 36 2 1 1 4 — 8 —
216 576 *1-*8 *9 *17-*24 *25 36 2 1 1 4 — 8 —
217 576 *1-*8 *9-*16 *17 *25 36 2 1 1 4 — 8 —
218 608 *1-*5 *9-*13 *17-*21 *25-*28 38 2 1 1 4 — 8 —
219 608 *1-*6 *9-*12 *17-*22 *25-*27 38 2 1 1 4 — 8 —
220 608 *1-*6 *9-*13 *17-*20 *25-*28 38 2 1 1 4 — 8 —
221 608 *1-*6 *9-*13 *17-*21 *25-*27 38 2 1 1 4 — 8 —
222 608 *1-*6 *9-*13 *17-*22 *25,*26 38 2 1 1 4 — 8 —
223 608 *1-*6 *9-*14 *17-*20 *25-*27 38 2 1 1 4 — 8 —
224 608 *1-*6 *9-*14 *17-*21 *25,*26 38 2 1 1 4 — 8 —
225 608 *1-*6 *9-*14 *17-*22 *25 38 2 1 1 4 — 8 —
226 608 *1-*7 *9-*11 *17-*23 *25,*26 38 2 1 1 4 — 8 —
227 608 *1-*7 *9-*12 *17-*20 *25-*28 38 2 1 1 4 — 8 —
228 608 *1-*7 *9-*12 *17-*23 *25 38 2 1 1 4 — 8 —
229 608 *1-*7 *9-*13 *17-*20 *25-*27 38 2 1 1 4 — 8 —
230 608 *1-*7 *9-*13 *17-*21 *25,*26 38 2 1 1 4 — 8 —
231 608 *1-*7 *9-*15 *17-*19 *25,*26 38 2 1 1 4 — 8 —
232 608 *1-*7 *9-*15 *17-*20 *25 38 2 1 1 4 — 8 —
233 608 *1-*8 *9,*10 *17-*24 *25 38 2 1 1 4 — 8 —
234 608 *1-*8 *9-*16 *17,*18 *25 38 2 1 1 4 — 8 —
235 640 *1-*5 *9-*13 *17-*21 *25-*29 40 2 1 1 4 — 8 —
236 640 *1-*6 *9-*12 *17-*22 *25-*28 40 2 1 1 4 — 8 —
237 640 *1-*6 *9-*13 *17-*21 *25-*28 40 2 1 1 4 — 8 —
238 640 *1-*6 *9-*13 *17-*22 *25-*27 40 2 1 1 4 — 8 —
239 640 *1-*6 *9-*14 *17-*20 *25-*28 40 2 1 1 4 — 8 —
240 640 *1-*6 *9-*14 *17-*21 *25-*27 40 2 1 1 4 — 8 —
241 640 *1-*6 *9-*14 *17-*22 *25,*26 40 2 1 1 4 — 8 —
242 640 *1-*7 *9-*11 *17-*23 *25-*27 40 2 1 1 4 — 8 —
243 640 *1-*7 *9-*12 *17-*23 *25,*26 40 2 1 1 4 — 8 —
244 640 *1-*7 *9-*13 *17-*20 *25-*28 40 2 1 1 4 — 8 —
245 640 *1-*7 *9-*13 *17-*21 *25-*27 40 2 1 1 4 — 8 —
(To be continued)

INST03-10-490
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-500

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 16G 128 256
246 640 *1-*7 *9-*13 *17-*23 *25 40 2 1 1 4 — 8 —
247 640 *1-*7 *9-*14 *17-*22 *25 40 2 1 1 4 — 8 —
248 640 *1-*7 *9-*15 *17-*19 *25-*27 40 2 1 1 4 — 8 —
249 640 *1-*7 *9-*15 *17-*20 *25,*26 40 2 1 1 4 — 8 —
250 640 *1-*7 *9-*15 *17-*21 *25 40 2 1 1 4 — 8 —
251 640 *1-*8 *9,*10 *17-*24 *25,*26 40 2 1 1 4 — 8 —
252 640 *1-*8 *9-*11 *17-*24 *25 40 2 1 1 4 — 8 —
253 640 *1-*8 *9-*16 *17-*19 *25 40 2 1 1 4 — 8 —
254 672 *1-*6 *9-*13 *17-*21 *25-*29 42 2 1 1 4 — 8 —
255 672 *1-*6 *9-*13 *17-*22 *25-*28 42 2 1 1 4 — 8 —
256 672 *1-*6 *9-*14 *17-*21 *25-*28 42 2 1 1 4 — 8 —
257 672 *1-*6 *9-*14 *17-*22 *25-*27 42 2 1 1 4 — 8 —
258 672 *1-*7 *9-*12 *17-*23 *25-*27 42 2 1 1 4 — 8 —
259 672 *1-*7 *9-*13 *17-*21 *25-*28 42 2 1 1 4 — 8 —
260 672 *1-*7 *9-*13 *17-*23 *25,*26 42 2 1 1 4 — 8 —
261 672 *1-*7 *9-*14 *17-*22 *25,*26 42 2 1 1 4 — 8 —
262 672 *1-*7 *9-*14 *17-*23 *25 42 2 1 1 4 — 8 —
263 672 *1-*7 *9-*15 *17-*20 *25-*27 42 2 1 1 4 — 8 —
264 672 *1-*7 *9-*15 *17-*21 *25,*26 42 2 1 1 4 — 8 —
265 672 *1-*7 *9-*15 *17-*22 *25 42 2 1 1 4 — 8 —
266 672 *1-*8 *9-*11 *17-*24 *25,*26 42 2 1 1 4 — 8 —
267 672 *1-*8 *9-*12 *17-*24 *25 42 2 1 1 4 — 8 —
268 672 *1-*8 *9-*16 *17-*20 *25 42 2 1 1 4 — 8 —
269 704 *1-*6 *9-*13 *17-*22 *25-*29 44 2 1 1 4 — 8 —
270 704 *1-*6 *9-*14 *17-*21 *25-*29 44 2 1 1 4 — 8 —
271 704 *1-*6 *9-*14 *17-*22 *25-*28 44 2 1 1 4 — 8 —
272 704 *1-*7 *9-*12 *17-*23 *25-*28 44 2 1 1 4 — 8 —
273 704 *1-*7 *9-*13 *17-*21 *25-*29 44 2 1 1 4 — 8 —
274 704 *1-*7 *9-*13 *17-*23 *25-*27 44 2 1 1 4 — 8 —
275 704 *1-*7 *9-*14 *17-*22 *25-*27 44 2 1 1 4 — 8 —
276 704 *1-*7 *9-*14 *17-*23 *25,*26 44 2 1 1 4 — 8 —
277 704 *1-*7 *9-*15 *17-*20 *25-*28 44 2 1 1 4 — 8 —
278 704 *1-*7 *9-*15 *17-*21 *25-*27 44 2 1 1 4 — 8 —
279 704 *1-*7 *9-*15 *17-*22 *25,*26 44 2 1 1 4 — 8 —
280 704 *1-*7 *9-*15 *17-*23 *25 44 2 1 1 4 — 8 —
(To be continued)

INST03-10-500
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-510

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 16G 128 256
281 704 *1-*8 *9-*11 *17-*24 *25-*27 44 2 1 1 4 — 8 —
282 704 *1-*8 *9-*12 *17-*24 *25,*26 44 2 1 1 4 — 8 —
283 704 *1-*8 *9-*13 *17-*24 *25 44 2 1 1 4 — 8 —
284 704 *1-*8 *9-*16 *17-*21 *25 44 2 1 1 4 — 8 —
285 736 *1-*6 *9-*14 *17-*22 *25-*29 46 2 1 1 4 — 8 —
286 736 *1-*7 *9-*13 *17-*23 *25-*28 46 2 1 1 4 — 8 —
287 736 *1-*7 *9-*14 *17-*22 *25-*28 46 2 1 1 4 — 8 —
288 736 *1-*7 *9-*14 *17-*23 *25-*27 46 2 1 1 4 — 8 —
289 736 *1-*7 *9-*15 *17-*21 *25-*28 46 2 1 1 4 — 8 —
290 736 *1-*7 *9-*15 *17-*22 *25-*27 46 2 1 1 4 — 8 —
291 736 *1-*7 *9-*15 *17-*23 *25,*26 46 2 1 1 4 — 8 —
292 736 *1-*8 *9-*12 *17-*24 *25-*27 46 2 1 1 4 — 8 —
293 736 *1-*8 *9-*13 *17-*24 *25,*26 46 2 1 1 4 — 8 —
294 736 *1-*8 *9-*14 *17-*24 *25 46 2 1 1 4 — 8 —
295 736 *1-*8 *9-*16 *17-*22 *25 46 2 1 1 4 — 8 —
296 768 *1-*6 *9-*14 *17-*22 *25-*30 48 2 1 1 4 — 8 —
297 768 *1-*7 *9-*13 *17-*23 *25-*29 48 2 1 1 4 — 8 —
298 768 *1-*7 *9-*14 *17-*22 *25-*29 48 2 1 1 4 — 8 —
299 768 *1-*7 *9-*14 *17-*23 *25-*28 48 2 1 1 4 — 8 —
300 768 *1-*7 *9-*15 *17-*21 *25-*29 48 2 1 1 4 — 8 —
301 768 *1-*7 *9-*15 *17-*22 *25-*28 48 2 1 1 4 — 8 —
302 768 *1-*7 *9-*15 *17-*23 *25-*27 48 2 1 1 4 — 8 —
303 768 *1-*8 *9-*12 *17-*24 *25-*28 48 2 1 1 4 — 8 —
304 768 *1-*8 *9-*13 *17-*24 *25-*27 48 2 1 1 4 — 8 —
305 768 *1-*8 *9-*14 *17-*24 *25,*26 48 2 1 1 4 — 8 —
306 768 *1-*8 *9-*15 *17-*24 *25 48 2 1 1 4 — 8 —
307 768 *1-*8 *9-*16 *17-*23 *25 48 2 1 1 4 — 8 —
308 800 *1-*7 *9-*14 *17-*22 *25-*30 50 2 1 1 4 — 8 —
309 800 *1-*7 *9-*14 *17-*23 *25-*29 50 2 1 1 4 — 8 —
310 800 *1-*7 *9-*15 *17-*22 *25-*29 50 2 1 1 4 — 8 —
311 800 *1-*7 *9-*15 *17-*23 *25-*28 50 2 1 1 4 — 8 —
312 800 *1-*8 *9-*13 *17-*24 *25-*28 50 2 1 1 4 — 8 —
313 800 *1-*8 *9-*14 *17-*24 *25-*27 50 2 1 1 4 — 8 —
314 800 *1-*8 *9-*15 *17-*24 *25,*26 50 2 1 1 4 — 8 —
315 800 *1-*8 *9-*16 *17-*24 *25 50 2 1 1 4 — 8 —
(To be continued)

INST03-10-510
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-520

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 16G 128 256
316 832 *1-*7 *9-*14 *17-*23 *25-*30 52 2 1 1 4 — 8 —
317 832 *1-*7 *9-*15 *17-*22 *25-*30 52 2 1 1 4 — 8 —
318 832 *1-*7 *9-*15 *17-*23 *25-*29 52 2 1 1 4 — 8 —
319 832 *1-*8 *9-*13 *17-*24 *25-*29 52 2 1 1 4 — 8 —
320 832 *1-*8 *9-*14 *17-*24 *25-*28 52 2 1 1 4 — 8 —
321 832 *1-*8 *9-*15 *17-*24 *25-*27 52 2 1 1 4 — 8 —
322 832 *1-*8 *9-*16 *17-*24 *25,*26 52 2 1 1 4 — 8 —
323 864 *1-*7 *9-*15 *17-*23 *25-*30 54 2 1 1 4 — 8 —
324 864 *1-*8 *9-*14 *17-*24 *25-*29 54 2 1 1 4 — 8 —
325 864 *1-*8 *9-*15 *17-*24 *25-*28 54 2 1 1 4 — 8 —
326 864 *1-*8 *9-*16 *17-*24 *25-*27 54 2 1 1 4 — 8 —
327 896 *1-*7 *9-*15 *17-*23 *25-*31 56 2 1 1 4 — 8 —
328 896 *1-*8 *9-*14 *17-*24 *25-*30 56 2 1 1 4 — 8 —
329 896 *1-*8 *9-*15 *17-*24 *25-*29 56 2 1 1 4 — 8 —
330 896 *1-*8 *9-*16 *17-*24 *25-*28 56 2 1 1 4 — 8 —
331 928 *1-*8 *9-*15 *17-*24 *25-*30 58 2 1 1 4 — 8 —
332 928 *1-*8 *9-*16 *17-*24 *25-*29 58 2 1 1 4 — 8 —
333 960 *1-*8 *9-*15 *17-*24 *25-*31 60 2 1 1 4 — 8 —
334 960 *1-*8 *9-*16 *17-*24 *25-*30 60 2 1 1 4 — 8 —
335 992 *1-*8 *9-*16 *17-*24 *25-*31 62 2 1 1 4 — 8 —
336 1024 *1-*8 *9-*16 *17-*24 *25-*32 64 2 1 1 4 — 8 —

NOTE 1: The above numbers (*1 through *32) represent the CM Module locations shown in
Fig. 3.10-25, Fig. 3.10-26, Fig. 3.10-47 or Fig. 3.10-48.
NOTE 2: The required SM capacity shown in Table 6.1-1 (INST06-10) must be installed in
CPEX-0.

INST03-10-520
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-530

Table 3.10-9 Cache memory capacity and number of necessary options 

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 32G 128 256
1 128 *1 — *17 — 4 0 1 0 2 0 4 0
2 192 *1,*2 — *17 — 6 0 1 0 2 0 4 0
3 256 *1 *9 *17 *25 8 2 1 1 4 0 8 0
4 256 *1,*2 — *17,*18 — 8 0 1 0 2 0 4 0
5 256 *1-*3 — *17 — 8 0 1 0 2 0 4 0
6 320 *1,*2 *9 *17 *25 10 2 1 1 4 0 8 0
7 320 *1-*3 — *17,*18 — 10 0 1 0 2 0 4 0
8 320 *1-*4 — *17 — 10 0 1 0 2 0 4 0
9 384 *1,*2 *9 *17,*18 *25 12 2 1 1 4 0 8 0
10 384 *1,*2 *9,*10 *17 *25 12 2 1 1 4 0 8 0
11 384 *1-*3 — *17-*19 — 12 0 1 0 2 0 4 0
12 384 *1-*3 *9 *17 *25 12 2 1 1 4 0 8 0
13 384 *1-*4 — *17,*18 — 12 0 1 0 2 0 4 0
14 384 *1-*5 — *17 — 12 0 1 0 1 1 2 2
15 448 *1,*2 *9,*10 *17,*18 *25 14 2 1 1 4 0 8 0
16 448 *1-*3 *9,*10 *17 *25 14 2 1 1 4 0 8 0
17 448 *1-*4 *9 *17 *25 14 2 1 1 4 0 8 0
18 448 *1-*5 — *17,*18 — 14 0 1 0 1 1 2 2
19 448 *1-*6 — *17 — 14 0 1 0 1 1 2 2
20 512 *1,*2 *9,*10 *17,*18 *25,*26 16 2 1 1 4 0 8 0
21 512 *1-*3 *9 *17-*19 *25 16 2 1 1 4 0 8 0
22 512 *1-*3 *9,*10 *17,*18 *25 16 2 1 1 4 0 8 0
23 512 *1-*3 *9-*11 *17 *25 16 2 1 1 4 0 8 0
24 512 *1-*4 — *17-*20 — 16 0 1 0 2 0 4 0
25 512 *1-*4 *9,*10 *17 *25 16 2 1 1 4 0 8 0
26 512 *1-*5 — *17-*19 — 16 0 1 0 1 1 2 2
27 512 *1-*5 *9 *17 *25 16 2 1 1 3 1 6 2
28 512 *1-*6 — *17,*18 — 16 0 1 0 1 1 2 2
29 512 *1-*7 — *17 — 16 0 1 0 1 1 2 2
30 576 *1-*3 *9,*10 *17,*18 *25,*26 18 2 1 1 4 0 8 0
31 576 *1-*3 *9,*10 *17-*19 *25 18 2 1 1 4 0 8 0
32 576 *1-*3 *9-*11 *17,*18 *25 18 2 1 1 4 0 8 0
33 576 *1-*4 *9,*10 *17,*18 *25 18 2 1 1 4 0 8 0
34 576 *1-*4 *9-*11 *17 *25 18 2 1 1 4 0 8 0
35 576 *1-*5 — *17-*20 — 18 0 1 0 1 1 2 2
(To be continued)

INST03-10-530
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-540

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 32G 128 256
36 576 *1-*5 *9,*10 *17 *25 18 2 1 1 3 1 6 2
37 576 *1-*6 — *17-*19 — 18 0 1 0 1 1 2 2
38 576 *1-*6 *9 *17 *25 18 2 1 1 3 1 6 2
39 576 *1-*7 — *17,*18 — 18 0 1 0 1 1 2 2
40 576 *1-*8 — *17 — 18 0 1 0 1 1 2 2
41 640 *1-*3 *9,*10 *17-*19 *25,*26 20 2 1 1 4 0 8 0
42 640 *1-*3 *9-*11 *17,*18 *25,*26 20 2 1 1 4 0 8 0
43 640 *1-*3 *9-*11 *17-*19 *25 20 2 1 1 4 0 8 0
44 640 *1-*4 *9 *17-*20 *25 20 2 1 1 4 0 8 0
45 640 *1-*4 *9,*10 *17,*18 *25,*26 20 2 1 1 4 0 8 0
46 640 *1-*4 *9-*11 *17,*18 *25 20 2 1 1 4 0 8 0
47 640 *1-*4 *9-*12 *17 *25 20 2 1 1 4 0 8 0
48 640 *1-*5 — *17-*21 — 20 0 1 0 0 2 0 4
49 640 *1-*5 *9,*10 *17,*18 *25 20 2 1 1 3 1 6 2
50 640 *1-*5 *9-*11 *17 *25 20 2 1 1 3 1 6 2
51 640 *1-*6 — *17-*20 — 20 0 1 0 1 1 2 2
52 640 *1-*6 *9,*10 *17 *25 20 2 1 1 3 1 6 2
53 640 *1-*7 — *17-*19 — 20 0 1 0 1 1 2 2
54 640 *1-*7 *9 *17 *25 20 2 1 1 3 1 6 2
55 640 *1-*8 — *17,*18 — 20 0 1 0 1 1 2 2
56 704 *1-*3 *9-*11 *17-*19 *25,*26 22 2 1 1 4 0 8 0
57 704 *1-*4 *9,*10 *17-*20 *25 22 2 1 1 4 0 8 0
58 704 *1-*4 *9-*11 *17,*18 *25,*26 22 2 1 1 4 0 8 0
59 704 *1-*4 *9-*11 *17-*19 *25 22 2 1 1 4 0 8 0
60 704 *1-*4 *9-*12 *17,*18 *25 22 2 1 1 4 0 8 0
61 704 *1-*5 *9,*10 *17,*18 *25,*26 22 2 1 1 3 1 6 2
62 704 *1-*5 *9-*11 *17,*18 *25 22 2 1 1 3 1 6 2
63 704 *1-*5 *9-*12 *17 *25 22 2 1 1 3 1 6 2
64 704 *1-*6 — *17-*21 — 22 0 1 0 0 2 0 4
65 704 *1-*6 *9,*10 *17,*18 *25 22 2 1 1 3 1 6 2
66 704 *1-*6 *9-*11 *17 *25 22 2 1 1 3 1 6 2
67 704 *1-*7 — *17-*20 — 22 0 1 0 1 1 2 2
68 704 *1-*7 *9,*10 *17 *25 22 2 1 1 3 1 6 2
69 704 *1-*8 — *17-*19 — 22 0 1 0 1 1 2 2
70 704 *1-*8 *9 *17 *25 22 2 1 1 3 1 6 2
(To be continued)

INST03-10-540
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-550

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 32G 128 256
71 768 *1-*3 *9-*11 *17-*19 *25-*27 24 2 1 1 4 0 8 0
72 768 *1-*4 *9,*10 *17-*20 *25,*26 24 2 1 1 4 0 8 0
73 768 *1-*4 *9-*11 *17-*19 *25,*26 24 2 1 1 4 0 8 0
74 768 *1-*4 *9-*11 *17-*20 *25 24 2 1 1 4 0 8 0
75 768 *1-*4 *9-*12 *17,*18 *25,*26 24 2 1 1 4 0 8 0
76 768 *1-*4 *9-*12 *17-*19 *25 24 2 1 1 4 0 8 0
77 768 *1-*5 *9 *17-*21 *25 24 2 1 1 2 2 4 4
78 768 *1-*5 *9-*11 *17,*18 *25,*26 24 2 1 1 3 1 6 2
79 768 *1-*5 *9-*11 *17-*19 *25 24 2 1 1 3 1 6 2
80 768 *1-*5 *9-*12 *17,*18 *25 24 2 1 1 3 1 6 2
81 768 *1-*5 *9-*13 *17 *25 24 2 1 1 2 2 4 4
82 768 *1-*6 — *17-*22 — 24 0 1 0 0 2 0 4
83 768 *1-*6 *9,*10 *17,*18 *25,*26 24 2 1 1 3 1 6 2
84 768 *1-*6 *9-*11 *17,*18 *25 24 2 1 1 3 1 6 2
85 768 *1-*6 *9-*12 *17 *25 24 2 1 1 3 1 6 2
86 768 *1-*7 — *17-*21 — 24 0 1 0 0 2 0 4
87 768 *1-*7 *9,*10 *17,*18 *25 24 2 1 1 3 1 6 2
88 768 *1-*7 *9-*11 *17 *25 24 2 1 1 3 1 6 2
89 768 *1-*8 — *17-*20 — 24 0 1 0 1 1 2 2
90 768 *1-*8 *9,*10 *17 *25 24 2 1 1 3 1 6 2
91 832 *1-*4 *9-*11 *17-*19 *25-*27 26 2 1 1 4 0 8 0
92 832 *1-*4 *9-*11 *17-*20 *25,*26 26 2 1 1 4 0 8 0
93 832 *1-*4 *9-*12 *17-*19 *25,*26 26 2 1 1 4 0 8 0
94 832 *1-*4 *9-*12 *17-*20 *25 26 2 1 1 4 0 8 0
95 832 *1-*5 *9,*10 *17-*21 *25 26 2 1 1 2 2 4 4
96 832 *1-*5 *9-*11 *17-*19 *25,*26 26 2 1 1 3 1 6 2
97 832 *1-*5 *9-*12 *17,*18 *25,*26 26 2 1 1 3 1 6 2
98 832 *1-*5 *9-*12 *17-*19 *25 26 2 1 1 3 1 6 2
99 832 *1-*5 *9-*13 *17,*18 *25 26 2 1 1 2 2 4 4
100 832 *1-*6 *9-*11 *17,*18 *25,*26 26 2 1 1 3 1 6 2
101 832 *1-*6 *9-*11 *17-*19 *25 26 2 1 1 3 1 6 2
102 832 *1-*6 *9-*12 *17,*18 *25 26 2 1 1 3 1 6 2
103 832 *1-*6 *9-*13 *17 *25 26 2 1 1 2 2 4 4
104 832 *1-*7 — *17-*22 — 26 0 1 0 0 2 0 4
105 832 *1-*7 *9,*10 *17,*18 *25,*26 26 2 1 1 3 1 6 2
(To be continued)

INST03-10-550
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-560

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 32G 128 256
106 832 *1-*7 *9-*11 *17,*18 *25 26 2 1 1 3 1 6 2
107 832 *1-*7 *9-*12 *17 *25 26 2 1 1 3 1 6 2
108 832 *1-*8 — *17-*21 — 26 0 1 0 0 2 0 4
109 832 *1-*8 *9-*11 *17 *25 26 2 1 1 3 1 6 2
110 896 *1-*4 *9-*11 *17-*20 *25-*27 28 2 1 1 4 0 8 0
111 896 *1-*4 *9-*12 *17-*19 *25-*27 28 2 1 1 4 0 8 0
112 896 *1-*4 *9-*12 *17-*20 *25,*26 28 2 1 1 4 0 8 0
113 896 *1-*5 *9,*10 *17-*21 *25,*26 28 2 1 1 2 2 4 4
114 896 *1-*5 *9-*11 *17-*19 *25-*27 28 2 1 1 3 1 6 2
115 896 *1-*5 *9-*11 *17-*21 *25 28 2 1 1 2 2 4 4
116 896 *1-*5 *9-*12 *17-*19 *25,*26 28 2 1 1 3 1 6 2
117 896 *1-*5 *9-*12 *17-*20 *25 28 2 1 1 3 1 6 2
118 896 *1-*5 *9-*13 *17,*18 *25,*26 28 2 1 1 2 2 4 4
119 896 *1-*5 *9-*13 *17-*19 *25 28 2 1 1 2 2 4 4
120 896 *1-*6 *9 *17-*22 *25 28 2 1 1 2 2 4 4
121 896 *1-*6 *9-*11 *17-*19 *25,*26 28 2 1 1 3 1 6 2
122 896 *1-*6 *9-*12 *17,*18 *25,*26 28 2 1 1 3 1 6 2
123 896 *1-*6 *9-*12 *17-*19 *25 28 2 1 1 3 1 6 2
124 896 *1-*6 *9-*13 *17,*18 *25 28 2 1 1 2 2 4 4
125 896 *1-*6 *9-*14 *17 *25 28 2 1 1 2 2 4 4
126 896 *1-*7 — *17-*23 — 28 0 1 0 0 2 0 4
127 896 *1-*7 *9-*11 *17,*18 *25,*26 28 2 1 1 3 1 6 2
128 896 *1-*7 *9-*11 *17-*19 *25 28 2 1 1 3 1 6 2
129 896 *1-*7 *9-*12 *17,*18 *25 28 2 1 1 3 1 6 2
130 896 *1-*7 *9-*13 *17 *25 28 2 1 1 2 2 4 4
131 896 *1-*8 — *17-*22 — 28 0 1 0 0 2 0 4
132 896 *1-*8 *9-*12 *17 *25 28 2 1 1 3 1 6 2
133 960 *1-*4 *9-*12 *17-*20 *25-*27 30 2 1 1 4 0 8 0
134 960 *1-*5 *9-*11 *17-*21 *25,*26 30 2 1 1 2 2 4 4
135 960 *1-*5 *9-*12 *17-*19 *25-*27 30 2 1 1 3 1 6 2
136 960 *1-*5 *9-*12 *17-*20 *25,*26 30 2 1 1 3 1 6 2
137 960 *1-*5 *9-*12 *17-*21 *25 30 2 1 1 2 2 4 4
138 960 *1-*5 *9-*13 *17-*19 *25,*26 30 2 1 1 2 2 4 4
139 960 *1-*5 *9-*13 *17-*20 *25 30 2 1 1 2 2 4 4
140 960 *1-*6 *9,*10 *17-*22 *25 30 2 1 1 2 2 4 4
(To be continued)

INST03-10-560
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-570

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 32G 128 256
141 960 *1-*6 *9-*11 *17-*19 *25-*27 30 2 1 1 3 1 6 2
142 960 *1-*6 *9-*12 *17-*19 *25,*26 30 2 1 1 3 1 6 2
143 960 *1-*6 *9-*12 *17-*20 *25 30 2 1 1 3 1 6 2
144 960 *1-*6 *9-*13 *17,*18 *25,*26 30 2 1 1 2 2 4 4
145 960 *1-*6 *9-*13 *17-*19 *25 30 2 1 1 2 2 4 4
146 960 *1-*6 *9-*14 *17,*18 *25 30 2 1 1 2 2 4 4
147 960 *1-*7 *9-*11 *17-*19 *25,*26 30 2 1 1 3 1 6 2
148 960 *1-*7 *9-*12 *17,*18 *25,*26 30 2 1 1 3 1 6 2
149 960 *1-*7 *9-*12 *17-*19 *25 30 2 1 1 3 1 6 2
150 960 *1-*7 *9-*13 *17,*18 *25 30 2 1 1 2 2 4 4
151 960 *1-*8 — *17-*23 — 30 0 1 0 0 2 0 4
152 960 *1-*8 *9-*13 *17 *25 30 2 1 1 2 2 4 4
153 1024 *1-*4 *9-*12 *17-*20 *25-*28 32 2 1 1 4 0 8 0
154 1024 *1-*5 *9-*11 *17-*21 *25-*27 32 2 1 1 2 2 4 4
155 1024 *1-*5 *9-*12 *17-*20 *25-*27 32 2 1 1 3 1 6 2
156 1024 *1-*5 *9-*12 *17-*21 *25,*26 32 2 1 1 2 2 4 4
157 1024 *1-*5 *9-*13 *17-*19 *25-*27 32 2 1 1 2 2 4 4
158 1024 *1-*5 *9-*13 *17-*20 *25,*26 32 2 1 1 2 2 4 4
159 1024 *1-*5 *9-*13 *17-*21 *25 32 2 1 1 1 3 2 6
160 1024 *1-*6 *9,*10 *17-*22 *25,*26 32 2 1 1 2 2 4 4
161 1024 *1-*6 *9-*11 *17-*22 *25 32 2 1 1 2 2 4 4
162 1024 *1-*6 *9-*12 *17-*19 *25-*27 32 2 1 1 3 1 6 2
163 1024 *1-*6 *9-*12 *17-*20 *25,*26 32 2 1 1 3 1 6 2
164 1024 *1-*6 *9-*13 *17-*19 *25,*26 32 2 1 1 2 2 4 4
165 1024 *1-*6 *9-*13 *17-*20 *25 32 2 1 1 2 2 4 4
166 1024 *1-*6 *9-*14 *17,*18 *25,*26 32 2 1 1 2 2 4 4
167 1024 *1-*6 *9-*14 *17-*19 *25 32 2 1 1 2 2 4 4
168 1024 *1-*7 *9 *17-*23 *25 32 2 1 1 2 2 4 4
169 1024 *1-*7 *9-*11 *17-*19 *25-*27 32 2 1 1 3 1 6 2
170 1024 *1-*7 *9-*12 *17-*19 *25,*26 32 2 1 1 3 1 6 2
171 1024 *1-*7 *9-*12 *17-*20 *25 32 2 1 1 3 1 6 2
172 1024 *1-*7 *9-*13 *17,*18 *25,*26 32 2 1 1 2 2 4 4
173 1024 *1-*7 *9-*13 *17-*19 *25 32 2 1 1 2 2 4 4
174 1024 *1-*7 *9-*15 *17 *25 32 2 1 1 2 2 4 4
175 1024 *1-*8 — *17-*24 — 32 0 1 0 0 2 0 4
(To be continued)

INST03-10-570
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-580

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 32G 128 256
176 1024 *1-*8 *9-*14 *17 *25 32 2 1 1 2 2 4 4
177 1088 *1-*5 *9-*12 *17-*20 *25-*28 34 2 1 1 3 1 6 2
178 1088 *1-*5 *9-*12 *17-*21 *25-*27 34 2 1 1 2 2 4 4
179 1088 *1-*5 *9-*13 *17-*20 *25-*27 34 2 1 1 2 2 4 4
180 1088 *1-*5 *9-*13 *17-*21 *25,*26 34 2 1 1 1 3 2 6
181 1088 *1-*6 *9-*11 *17-*22 *25,*26 34 2 1 1 2 2 4 4
182 1088 *1-*6 *9-*12 *17-*20 *25-*27 34 2 1 1 3 1 6 2
183 1088 *1-*6 *9-*12 *17-*22 *25 34 2 1 1 2 2 4 4
184 1088 *1-*6 *9-*13 *17-*19 *25-*27 34 2 1 1 2 2 4 4
185 1088 *1-*6 *9-*13 *17-*20 *25,*26 34 2 1 1 2 2 4 4
186 1088 *1-*6 *9-*13 *17-*21 *25 34 2 1 1 1 3 2 6
187 1088 *1-*6 *9-*14 *17-*19 *25,*26 34 2 1 1 2 2 4 4
188 1088 *1-*6 *9-*14 *17-*20 *25 34 2 1 1 2 2 4 4
189 1088 *1-*7 *9,*10 *17-*23 *25 34 2 1 1 2 2 4 4
190 1088 *1-*7 *9-*12 *17-*19 *25-*27 34 2 1 1 3 1 6 2
191 1088 *1-*7 *9-*12 *17-*20 *25,*26 34 2 1 1 3 1 6 2
192 1088 *1-*7 *9-*13 *17-*19 *25,*26 34 2 1 1 2 2 4 4
193 1088 *1-*7 *9-*13 *17-*20 *25 34 2 1 1 2 2 4 4
194 1088 *1-*7 *9-*15 *17,*18 *25 34 2 1 1 2 2 4 4
195 1088 *1-*8 *9-*15 *17 *25 34 2 1 1 2 2 4 4
196 1152 *1-*5 *9-*12 *17-*21 *25-*28 36 2 1 1 2 2 4 4
197 1152 *1-*5 *9-*13 *17-*20 *25-*28 36 2 1 1 2 2 4 4
198 1152 *1-*5 *9-*13 *17-*21 *25-*27 36 2 1 1 1 3 2 6
199 1152 *1-*6 *9-*11 *17-*22 *25-*27 36 2 1 1 2 2 4 4
200 1152 *1-*6 *9-*12 *17-*20 *25-*28 36 2 1 1 3 1 6 2
201 1152 *1-*6 *9-*12 *17-*22 *25,*26 36 2 1 1 2 2 4 4
202 1152 *1-*6 *9-*13 *17-*20 *25-*27 36 2 1 1 2 2 4 4
203 1152 *1-*6 *9-*13 *17-*21 *25,*26 36 2 1 1 1 3 2 6
204 1152 *1-*6 *9-*13 *17-*22 *25 36 2 1 1 1 3 2 6
205 1152 *1-*6 *9-*13 *17-*22 *25 36 2 1 1 1 3 2 6
206 1152 *1-*6 *9-*14 *17-*19 *25-*27 36 2 1 1 2 2 4 4
207 1152 *1-*6 *9-*14 *17-*20 *25,*26 36 2 1 1 2 2 4 4
208 1152 *1-*6 *9-*14 *17-*21 *25 36 2 1 1 1 3 2 6
209 1152 *1-*7 *9,*10 *17-*23 *25,*26 36 2 1 1 2 2 4 4
210 1152 *1-*7 *9-*11 *17-*23 *25 36 2 1 1 2 2 4 4
(To be continued)

INST03-10-580
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-590

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 32G 128 256
211 1152 *1-*7 *9-*12 *17-*20 *25-*27 36 2 1 1 3 1 6 2
212 1152 *1-*7 *9-*13 *17-*19 *25-*27 36 2 1 1 2 2 4 4
213 1152 *1-*7 *9-*13 *17-*20 *25,*26 36 2 1 1 2 2 4 4
214 1152 *1-*7 *9-*13 *17-*21 *25 36 2 1 1 1 3 2 6
215 1152 *1-*7 *9-*15 *17-*19 *25 36 2 1 1 2 2 4 4
216 1152 *1-*8 *9 *17-*24 *25 36 2 1 1 2 2 4 4
217 1152 *1-*8 *9-*16 *17 *25 36 2 1 1 2 2 4 4
218 1216 *1-*5 *9-*13 *17-*21 *25-*28 38 2 1 1 1 3 2 6
219 1216 *1-*6 *9-*12 *17-*22 *25-*27 38 2 1 1 2 2 4 4
220 1216 *1-*6 *9-*13 *17-*20 *25-*28 38 2 1 1 2 2 4 4
221 1216 *1-*6 *9-*13 *17-*21 *25-*27 38 2 1 1 1 3 2 6
222 1216 *1-*6 *9-*13 *17-*22 *25,*26 38 2 1 1 1 3 2 6
223 1216 *1-*6 *9-*14 *17-*20 *25-*27 38 2 1 1 2 2 4 4
224 1216 *1-*6 *9-*14 *17-*21 *25,*26 38 2 1 1 1 3 2 6
225 1216 *1-*6 *9-*14 *17-*22 *25 38 2 1 1 1 3 2 6
226 1216 *1-*7 *9-*11 *17-*23 *25,*26 38 2 1 1 2 2 4 4
227 1216 *1-*7 *9-*12 *17-*20 *25-*28 38 2 1 1 3 1 6 2
228 1216 *1-*7 *9-*12 *17-*23 *25 38 2 1 1 2 2 4 4
229 1216 *1-*7 *9-*13 *17-*20 *25-*27 38 2 1 1 2 2 4 4
230 1216 *1-*7 *9-*13 *17-*21 *25,*26 38 2 1 1 1 3 2 6
231 1216 *1-*7 *9-*15 *17-*19 *25,*26 38 2 1 1 2 2 4 4
232 1216 *1-*7 *9-*15 *17-*20 *25 38 2 1 1 2 2 4 4
233 1216 *1-*8 *9,*10 *17-*24 *25 38 2 1 1 2 2 4 4
234 1216 *1-*8 *9-*16 *17,*18 *25 38 2 1 1 2 2 4 4
235 1280 *1-*5 *9-*13 *17-*21 *25-*29 40 2 1 1 0 4 0 8
236 1280 *1-*6 *9-*12 *17-*22 *25-*28 40 2 1 1 2 2 4 4
237 1280 *1-*6 *9-*13 *17-*21 *25-*28 40 2 1 1 1 3 2 6
238 1280 *1-*6 *9-*13 *17-*22 *25-*27 40 2 1 1 1 3 2 6
239 1280 *1-*6 *9-*14 *17-*20 *25-*28 40 2 1 1 2 2 4 4
240 1280 *1-*6 *9-*14 *17-*21 *25-*27 40 2 1 1 1 3 2 6
241 1280 *1-*6 *9-*14 *17-*22 *25,*26 40 2 1 1 1 3 2 6
242 1280 *1-*7 *9-*11 *17-*23 *25-*27 40 2 1 1 2 2 4 4
243 1280 *1-*7 *9-*12 *17-*23 *25,*26 40 2 1 1 2 2 4 4
244 1280 *1-*7 *9-*13 *17-*20 *25-*28 40 2 1 1 2 2 4 4
245 1280 *1-*7 *9-*13 *17-*21 *25-*27 40 2 1 1 1 3 2 6
(To be continued)

INST03-10-590
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-600

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 32G 128 256
246 1280 *1-*7 *9-*13 *17-*23 *25 40 2 1 1 1 3 2 6
247 1280 *1-*7 *9-*14 *17-*22 *25 40 2 1 1 1 3 2 6
248 1280 *1-*7 *9-*15 *17-*19 *25-*27 40 2 1 1 2 2 4 4
249 1280 *1-*7 *9-*15 *17-*20 *25,*26 40 2 1 1 2 2 4 4
250 1280 *1-*7 *9-*15 *17-*21 *25 40 2 1 1 1 3 2 6
251 1280 *1-*8 *9,*10 *17-*24 *25,*26 40 2 1 1 2 2 4 4
252 1280 *1-*8 *9-*11 *17-*24 *25 40 2 1 1 2 2 4 4
253 1280 *1-*8 *9-*16 *17-*19 *25 40 2 1 1 2 2 4 4
254 1344 *1-*6 *9-*13 *17-*21 *25-*29 42 2 1 1 0 4 0 8
255 1344 *1-*6 *9-*13 *17-*22 *25-*28 42 2 1 1 1 3 2 6
256 1344 *1-*6 *9-*14 *17-*21 *25-*28 42 2 1 1 1 3 2 6
257 1344 *1-*6 *9-*14 *17-*22 *25-*27 42 2 1 1 1 3 2 6
258 1344 *1-*7 *9-*12 *17-*23 *25-*27 42 2 1 1 2 2 4 4
259 1344 *1-*7 *9-*13 *17-*21 *25-*28 42 2 1 1 1 3 2 6
260 1344 *1-*7 *9-*13 *17-*23 *25,*26 42 2 1 1 1 3 2 6
261 1344 *1-*7 *9-*14 *17-*22 *25,*26 42 2 1 1 1 3 2 6
262 1344 *1-*7 *9-*14 *17-*23 *25 42 2 1 1 1 3 2 6
263 1344 *1-*7 *9-*15 *17-*20 *25-*27 42 2 1 1 2 2 4 4
264 1344 *1-*7 *9-*15 *17-*21 *25,*26 42 2 1 1 1 3 2 6
265 1344 *1-*7 *9-*15 *17-*22 *25 42 2 1 1 1 3 2 6
266 1344 *1-*8 *9-*11 *17-*24 *25,*26 42 2 1 1 2 2 4 4
267 1344 *1-*8 *9-*12 *17-*24 *25 42 2 1 1 2 2 4 4
268 1344 *1-*8 *9-*16 *17-*20 *25 42 2 1 1 2 2 4 4
269 1408 *1-*6 *9-*13 *17-*22 *25-*29 44 2 1 1 0 4 0 8
270 1408 *1-*6 *9-*14 *17-*21 *25-*29 44 2 1 1 0 4 0 8
271 1408 *1-*6 *9-*14 *17-*22 *25-*28 44 2 1 1 1 3 2 6
272 1408 *1-*7 *9-*12 *17-*23 *25-*28 44 2 1 1 2 2 4 4
273 1408 *1-*7 *9-*13 *17-*21 *25-*29 44 2 1 1 0 4 0 8
274 1408 *1-*7 *9-*13 *17-*23 *25-*27 44 2 1 1 1 3 2 6
275 1408 *1-*7 *9-*14 *17-*22 *25-*27 44 2 1 1 1 3 2 6
276 1408 *1-*7 *9-*14 *17-*23 *25,*26 44 2 1 1 1 3 2 6
277 1408 *1-*7 *9-*15 *17-*20 *25-*28 44 2 1 1 2 2 4 4
278 1408 *1-*7 *9-*15 *17-*21 *25-*27 44 2 1 1 1 3 2 6
279 1408 *1-*7 *9-*15 *17-*22 *25,*26 44 2 1 1 1 3 2 6
280 1408 *1-*7 *9-*15 *17-*23 *25 44 2 1 1 1 3 2 6
(To be continued)

INST03-10-600
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-610

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 32G 128 256
281 1408 *1-*8 *9-*11 *17-*24 *25-*27 44 2 1 1 2 2 4 4
282 1408 *1-*8 *9-*12 *17-*24 *25,*26 44 2 1 1 2 2 4 4
283 1408 *1-*8 *9-*13 *17-*24 *25 44 2 1 1 1 3 2 6
284 1408 *1-*8 *9-*16 *17-*21 *25 44 2 1 1 1 3 2 6
285 1472 *1-*6 *9-*14 *17-*22 *25-*29 46 2 1 1 0 4 0 8
286 1472 *1-*7 *9-*13 *17-*23 *25-*28 46 2 1 1 1 3 2 6
287 1472 *1-*7 *9-*14 *17-*22 *25-*28 46 2 1 1 1 3 2 6
288 1472 *1-*7 *9-*14 *17-*23 *25-*27 46 2 1 1 1 3 2 6
289 1472 *1-*7 *9-*15 *17-*21 *25-*28 46 2 1 1 1 3 2 6
290 1472 *1-*7 *9-*15 *17-*22 *25-*27 46 2 1 1 1 3 2 6
291 1472 *1-*7 *9-*15 *17-*23 *25,*26 46 2 1 1 1 3 2 6
292 1472 *1-*8 *9-*12 *17-*24 *25-*27 46 2 1 1 2 2 4 4
293 1472 *1-*8 *9-*13 *17-*24 *25,*26 46 2 1 1 1 3 2 6
294 1472 *1-*8 *9-*14 *17-*24 *25 46 2 1 1 1 3 2 6
295 1472 *1-*8 *9-*16 *17-*22 *25 46 2 1 1 1 3 2 6
296 1536 *1-*6 *9-*14 *17-*22 *25-*30 48 2 1 1 0 4 0 8
297 1536 *1-*7 *9-*13 *17-*23 *25-*29 48 2 1 1 0 4 0 8
298 1536 *1-*7 *9-*14 *17-*22 *25-*29 48 2 1 1 0 4 0 8
299 1536 *1-*7 *9-*14 *17-*23 *25-*28 48 2 1 1 1 3 2 6
300 1536 *1-*7 *9-*15 *17-*21 *25-*29 48 2 1 1 0 4 0 8
301 1536 *1-*7 *9-*15 *17-*22 *25-*28 48 2 1 1 1 3 2 6
302 1536 *1-*7 *9-*15 *17-*23 *25-*27 48 2 1 1 1 3 2 6
303 1536 *1-*8 *9-*12 *17-*24 *25-*28 48 2 1 1 2 2 4 4
304 1536 *1-*8 *9-*13 *17-*24 *25-*27 48 2 1 1 1 3 2 6
305 1536 *1-*8 *9-*14 *17-*24 *25,*26 48 2 1 1 1 3 2 6
306 1536 *1-*8 *9-*15 *17-*24 *25 48 2 1 1 1 3 2 6
307 1536 *1-*8 *9-*16 *17-*23 *25 48 2 1 1 1 3 2 6
308 1600 *1-*7 *9-*14 *17-*22 *25-*30 50 2 1 1 0 4 0 8
309 1600 *1-*7 *9-*14 *17-*23 *25-*29 50 2 1 1 0 4 0 8
310 1600 *1-*7 *9-*15 *17-*22 *25-*29 50 2 1 1 0 4 0 8
311 1600 *1-*7 *9-*15 *17-*23 *25-*28 50 2 1 1 1 3 2 6
312 1600 *1-*8 *9-*13 *17-*24 *25-*28 50 2 1 1 1 3 2 6
313 1600 *1-*8 *9-*14 *17-*24 *25-*27 50 2 1 1 1 3 2 6
314 1600 *1-*8 *9-*15 *17-*24 *25,*26 50 2 1 1 1 3 2 6
315 1600 *1-*8 *9-*16 *17-*24 *25 50 2 1 1 1 3 2 6
(To be continued)

INST03-10-610
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-620

(Continued from the preceding page)

Cache CM Location (NOTE 1) Number of options
No. Memory DKC810I-CBXA DKC-F810I-CBXB DKC-F810I-
Capacity CPEX-0 CPEX-1 CPEX-2 CPEX-3 CM CPEX MOD5 MFC5 BKMS BKML BMM BMM
1CA/2CA 1CB/2CB 1CC/2CC 1CD/2CD 32G 128 256
316 1664 *1-*7 *9-*14 *17-*23 *25-*30 52 2 1 1 0 4 0 8
317 1664 *1-*7 *9-*15 *17-*22 *25-*30 52 2 1 1 0 4 0 8
318 1664 *1-*7 *9-*15 *17-*23 *25-*29 52 2 1 1 0 4 0 8
319 1664 *1-*8 *9-*13 *17-*24 *25-*29 52 2 1 1 0 4 0 8
320 1664 *1-*8 *9-*14 *17-*24 *25-*28 52 2 1 1 1 3 2 6
321 1664 *1-*8 *9-*15 *17-*24 *25-*27 52 2 1 1 1 3 2 6
322 1664 *1-*8 *9-*16 *17-*24 *25,*26 52 2 1 1 1 3 2 6
323 1728 *1-*7 *9-*15 *17-*23 *25-*30 54 2 1 1 0 4 0 8
324 1728 *1-*8 *9-*14 *17-*24 *25-*29 54 2 1 1 0 4 0 8
325 1728 *1-*8 *9-*15 *17-*24 *25-*28 54 2 1 1 1 3 2 6
326 1728 *1-*8 *9-*16 *17-*24 *25-*27 54 2 1 1 1 3 2 6
327 1792 *1-*7 *9-*15 *17-*23 *25-*31 56 2 1 1 0 4 0 8
328 1792 *1-*8 *9-*14 *17-*24 *25-*30 56 2 1 1 0 4 0 8
329 1792 *1-*8 *9-*15 *17-*24 *25-*29 56 2 1 1 0 4 0 8
330 1792 *1-*8 *9-*16 *17-*24 *25-*28 56 2 1 1 1 3 2 6
331 1856 *1-*8 *9-*15 *17-*24 *25-*30 58 2 1 1 0 4 0 8
332 1856 *1-*8 *9-*16 *17-*24 *25-*29 58 2 1 1 0 4 0 8
333 1920 *1-*8 *9-*15 *17-*24 *25-*31 60 2 1 1 0 4 0 8
334 1920 *1-*8 *9-*16 *17-*24 *25-*30 60 2 1 1 0 4 0 8
335 1984 *1-*8 *9-*16 *17-*24 *25-*31 62 2 1 1 0 4 0 8
336 2048 *1-*8 *9-*16 *17-*24 *25-*32 64 2 1 1 0 4 0 8

NOTE 1: The above numbers (*1 through *32) represent the CM Module locations shown in
Fig. 3.10-25, Fig. 3.10-26, Fig. 3.10-47 or Fig. 3.10-48.
NOTE 2: The required SM capacity shown in Table 6.1-1 (INST06-10) must be installed in
CPEX-0.

INST03-10-620
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-630

6-3 Insert the PCB.

a. When you need to install Additional Cache Path Control Adapter (DKC-F810I-CPEX),
remove the two screws and remove the dummy plate.
When you do not need to install Additional Cache Path Control Adapter (DKC-F810I-
CPEX), go to Step b.
NOTE: Store the removed dummy plate as it is required when the Additional Cache Path
Control Adapter is removed.

NOTICE: Remove the dummy plate just before installing the PCB.
If the dummy plate is kept removed for a long time, the wind doesn’t flow
among installed PCBs, causing the PCBs’ temperature rise which may result
in temperature warning or temperature alarm.

b. Install the CM PCB and tighten the two screws.

NOTE: When inserting the CM PCB, be careful not to get cables caught on anything.
c. If the cables were disconnected in Step 6-1 b, connect the cables to the CM PCB after
checking “3.1.7 Notes when connecting and disconnecting MFC cable” (INST03-01-190).

Main Edge Connector

PCB NOTICE: • Check that the main edge connector of the PCB has
no deformation, damage or sticking of dust before
installing the PCB. (See INST03-01-80)
• When installing the PCB, hold the top and bottom of
the PCB with both hands, and insert it straight not to
contact the neighboring PCB.

Table 3.10-10 Location of the CM PCB

Cluster Box Slot No. Location No. Remarks
1 DKC-0 1CA CACHE-1CA
1CB CACHE-1CB
DKC-1 1CC CACHE-1CC
1CD CACHE-1CD

INST03-10-630
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-640

DKC

CM PCB

Screw
Lever

CL1 1Cx-0
CL1 1Cx-1

Screw
CL1 1Cx-2 Lever Screw

CL1 1Cx-3

Dummy Plate

Fig. 3.10-28 Installation of PCB

INST03-10-640
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-650

7. SVP post procedure on the Cluster 1.

(1)
After completing the additional
installation of the cache memory on the
cluster 1, select (CL) [OK] in response to
“Replace or insert the Cache Memory
PCB(s)(Memory)of cluster-1. When
completed, please press OK.”.

(2) <CM Battery charging>

When you select [No] in “3. SVP pre procedure
(Battery)” (INST03-10-160) Step (1), the
progress of the charge is displayed.
When the amount of charge becomes 50% or
more, go to Step (3).
When you select [Cancel] (CL), go to Step (2)-
1.

(2)-1
“Do you want to stop this installation?”
When [Yes] is selected (CL), return to
INST03-10-110 Step (2)
When [No] is selected (CL), return to Step (2).

INST03-10-650
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-660

(3) <Cache CUDG executes>

“INLINE CUDG is now running...” is displayed.

(4)
“Changing the configuration date, for equipment of shared/cache memory...”
“Restoring the Cache Memory PCB...” is displayed.

NOTICE: Recover according to the procedure shown in “TROUBLE SHOOTING

SECTION” (Refer to TRBL02-470) when the mistake of the memory module
setting occurs.

INST03-10-660
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-670

8. Backup Module on the Cluster 2.

8-1 Recover one side of cache
When recovery processing is completed,
“The Cache Memory PCB is being blocked...”
“Lighting LED of the PCB...” message appears.
Processing proceeds to blocking of the other side of Cache Memory.

8-2 Check shut down LED

(1)
Select (CL)
* [Yes] if LED is on
* [No] if LED is off
in response to “Is the LED of the target
PCB(CACHE-nnn) lit?”.

(Eg. CACHE-2CA)

If [No] is selected:
Select (CL) [OK] after response to
“Check the location of the target
PCB(s)(CACHE-nnn), then pull out the
PCB(s) without considering the status of
LED.”.
Go to Step (2).
(Eg. CACHE-2CA)

INST03-10-670
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-680

(2) Check that the Shut Down LED on the CM PCB is lit.

2 2 1 1 2 2 1 1
C C C C C C C C
D C C D B A A B

Front View of DKC-1 Front View of DKC-0

Shut Down LED

(Red)

PS Failure LED
(Amber)

CM PCB

Fig. 3.10-29 Location of the Shut Down LED

Table 3.10-11 Location of the CM PCB

Cluster Box Slot No. Location No. Remarks
2 DKC-0 2CA CACHE-2CA
2CB CACHE-2CB
DKC-1 2CC CACHE-2CC
2CD CACHE-2CD

INST03-10-680
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-690

8-3 Backup Module procedure

Perform an appropriate Backup Module process depending on cache capacity.
When replacement is required, go to Step 8-4.
When addition is required, go to Step 8-5.
When addition/replacement are required, go to Step 9.

8-4 Replace Backup Module (Cluster 2)

(1) <Confirmation of Backup Module replacement>
A message, “Replace the BKM(CFM),
and then select [OK]. BKM-nnn(CFM) :
BKMS(BM256) -> BKML(BM512)” is
displayed.

(Eg. BKM-2BB)

INST03-10-690
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-700

(2) Replace the BKM on the cluster 2.

(2)-1 Check that the Shut Down LED on the BKM is lit.

2BD 2BC 1BC 1BD 2BB 2BA 1BA 1BB

Front View of DKC-1 Front View of DKC-0

Shut Down LED (Red)

Front View of BKM

Fig. 3.10-30 Location of Shut Down LED

(2)-2 Check that the screws to secure the BKMs are tightened.
NOTE: If the screw is loose, the BKM may be extracted when the cables or the locking
clamp is moved.
(2)-3 Open the four locking clamps and move all the cables to where they cannot obstruct
removal of the BKM.

BKM Screw Cable

Front View of
DKC
Locking Clamp
Fig. 3.10-31 Moving Cables
INST03-10-700
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-710

(2)-4 Loosen the screw and remove the BKM from the DKC.

Main Edge Connector

PCB
NOTICE: When removing the PCB, hold the top and bottom of
the PCB with both hands, and pull it out straight not
to contact the neighboring PCB.

DKC

BKM

Screw
Lever

Fig. 3.10-32 Removal of BKM

INST03-10-710
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-720

(2)-5 Replace the parts.

(2)-5-1 When you need to install Cache Backup Module Kit (DKC-F810I-BKML) and Cache
Flash Memory (DKC-F810I-BMM256) at the same time, replace the BKM and CFM.
When you do not need to install DKC-F810I-BKML and DKC-F810I-BMM256 at the
same time, go to the Step (2)-5-2.

a. Remove the screw of the option BKM and remove the cover.

Screw
Cover

BKM

Fig. 3.10-33 Removal of Cover

b. Install the option CFM to the BKM and tighten it with the two screws.
c. Attach the cover to the BKM and tighten it with the screw.

CFM

Screw

BKM

Screw

Fig. 3.10-34 Attachment of CFM

INST03-10-720
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-730

(2)-5-2 When you need to install only Cache Backup Module Kit (DKC-F810I-BKML),
replace the BKM.
When you do not need to install only DKC-F810I-BKML, go to the Step (2)-5-3.

a. Remove the screw of the removed BKM and remove the cover.

Screw
Cover

BKM

Fig. 3.10-35 Removal of Cover

b. Remove the two screws and detach the CFM.

c. Remove the screw of the option BKM and remove the cover.
d. Install the CFM to the option BKM and tighten it with the two screws.
e. Attach the cover to the BKM and tighten it with the screw.

CFM

Screw

BKM

Screw

Fig. 3.10-36 Movement of CFM

INST03-10-730
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-740

(2)-5-3 When you need to install only Cache Flash Memory (DKC-F810I-BMM256), replace
the CFM.
When you do not need to install only DKC-F810I-BMM256, go to the Step (2)-6.

a. Remove the screw of the removed BKM and remove the cover.

Screw
Cover

BKM

Fig. 3.10-37 Removal of Cover

b. Remove the two screws and detach the CFM.

c. Install the option CFM to the BKM and tighten it with the two screws.
d. Attach the cover to the BKM and tighten it with the screw.

CFM

Screw

BKM

Screw

Fig. 3.10-38 Replacement of CFM

INST03-10-740
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-750

(2)-6 Install the BKM to the DKC and tighten it with the screw.
(2)-7 If the cables were moved aside in Procedure (2)-3, put them back in place.

Main Edge Connector

PCB NOTICE: • Check that the main edge connector of the PCB has
no deformation, damage or sticking of dust before
installing the PCB. (See INST03-01-80)
• When installing the PCB, hold the top and bottom of
the PCB with both hands, and insert it straight not to
contact the neighboring PCB.

DKC

BKM

Screw
Lever

Fig. 3.10-39 Installation of BKM

INST03-10-750
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-760

(3)
When a message, “Replace the
BKM(CFM), and then select [OK].
BKM-nnn(CFM) : BKMS(BM256) ->
BKML(BM512)” is displayed, select
(CL) the [OK] button.

(Eg. BKM-2BB)

8-3 Add Backup Module (Cluster 2)

(1) <Confirmation of Backup Module addition>
A message, “Insert the BKM-nnn, and
then select [OK].” is displayed.

(Eg. BKM-2BB)

INST03-10-760
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-770

(2) Install the BKM on the cluster 2.

(2)-1 Remove the screw of the option BKM and remove the cover.

Screw
Cover

BKM

Fig. 3.10-40 Removal of Cover

(2)-2 Install the option CFM to the BKM and tighten it with the two screws.
(2)-3 Attach the cover to the BKM and tighten it with the screw.

CFM

Screw

BKM

Screw

Fig. 3.10-41 Attachment of CFM

INST03-10-770
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-780

(2)-4 If the cables are attached to the BKMs, check that the screws to secure the BKMs are
tightened.
If the cables are not attached to the BKMs, go to Step (2)-6.
NOTE: If the screw is loose, the BKM may be extracted when the cables or the locking
clamp is moved.
(2)-5 Open the four locking clamps and move all the cables to where they cannot obstruct
insertion of the BKM.

BKM Screw Cable

Front View of
DKC
Locking Clamp
Fig. 3.10-42 Moving Cables

INST03-10-780
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-790

(2)-6 Loosen the screw and remove the dummy plate.

(2)-7 Install the BKM to the DKC and tighten the screw.
(2)-8 If the cables were moved aside in Step (2)-5, put them back in place.

Main Edge Connector

PCB NOTICE: • Check that the main edge connector of the PCB has
no deformation, damage or sticking of dust before
installing the PCB. (See INST03-01-80)
• When installing the PCB, hold the top and bottom of
the PCB with both hands, and insert it straight not to
contact the neighboring PCB.

2BD 2BC 1BC 1BD 2BB 2BA 1BA 1BB

Front View of DKC-1 Front View of DKC-0

DKC

BKM

Screw
Lever

Screw

Dummy Plate

Fig. 3.10-43 Installation of BKM

INST03-10-790
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-800

(2)-9 Store the Dummy Plates.

a. Loosen the three screws  on the front side of the DKC and remove the cable cover.
b. Loosen the screw  and remove the accessory box.
c. Put the dummy plates that were removed in the accessory box.
d. Put the accessory box in place and fix it with the screw .
e. Put the cable cover in place and fix it with the three screws .

Front View of DKC

Dummy
Plate

DKC

Accessory Box

Screw 
Front View Screw 

Screw 

Cable Cover

Fig. 3.10-44 Storage of Dummy Plates

INST03-10-800
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-810

(3)
When a message, “Insert the BKM-nnn,
and then select [OK].” is displayed, select
(CL) the [OK] button.

(Eg. BKM-2BB)

INST03-10-810
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-820

9. SVP pre procedure (Cluster 2).

(1) <Perform cache hardware installation>
At this point refrain from pressing the
[OK] button.
When “Replace or insert the Cache
Memory PCB(s)(Memory) of cluster-2.
When completed, please press OK.” is
displayed, install hardware components
according to the cache hardware
installation procedure.

Make sure of the installation location and

size of the module to be added and insert
the correct module in the correct location.
(The Shared Memory capacity may be
changed at the same time, depending on the set Cache Memory capacity.)

INST03-10-820
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-830

10. Install the Cache Memory on the cluster 2.

NOTICE: Be sure to wear your wrist strap and attach to ground prior to performing the
following work. This will ensure that the IC and LSI on the PCB are protected
from static electricity.

10-1 Remove the PCB.

a. If the cables are connected to the CM PCB, disconnect the cables after checking “3.1.7
Notes when connecting and disconnecting MFC cable” (INST03-01-190).
If the cables are not connected to the CM PCB, go to Step b.

INST03-10-830
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-840

b. Remove the two screws and remove the CM PCB.

NOTE: When removing the CM PCB, be careful not to pull cables.

Main Edge Connector

PCB
NOTICE: When removing the PCB, hold the top and bottom of
the PCB with both hands, and pull it out straight not to
contact the neighboring PCB.

DKC

CM PCB

Screw

Lever

Cable

Lever Screw

Fig. 3.10-45 Removal of PCB

INST03-10-840
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-850

10-2 Insert the CM Modules.

a. Loosen the screw and remove the cover.

Screw

CM PCB

Cover

Fig. 3.10-46 Removal of Cover

INST03-10-850
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-860

b. Remove the dust covers that match the required Cache Memory capacity referring to Fig.
3.10-47, Fig. 3.10-48, Fig. 3.10-49, Table 3.10-4 through Table 3.10-9.
c. Insert the CM Modules that match the required Cache Memory capacity.
d. Attach the cover and fasten the screws. (Refer to Fig. 3.10-46.)

CM Module Location of DKC-0

Cluster 2 (CACHE-2CA/2CB)

Removal of Dust Cover

A CM PCB Dust Cover
(WP840-A)
Socket
PCB
Viewed from A

CACHE-2CA (Basic) CACHE-2CB (Option 1)

CM1P: *2 CM1P: *10

CM5P: *6 CM5P: *14
CM3P: *4 CM3P: *12
CM7P: *8 CM7P: *16

CM6P: *7 CM6P: *15

CM2P: *3 CM2P: *11
CM4P: *5 CM4P: *13
CM0P: *1 CM0P: *9

NOTE1: The cache memory module location *1 through *16 correspond to the CM Location
listed in Table 3.10-4 through Table 3.10-9.
Fig. 3.10-47 Inserting Location of the CM Module

INST03-10-860
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-870

CM Module Location of DKC-1

Cluster 2 (CACHE-2CC/2CD)

Removal of Dust Cover

A CM PCB Dust Cover
(WP840-A) Socket
PCB
Viewed from A

CACHE-2CC (Option 2) CACHE-2CD (Option 3)

CM1P: *18 CM1P: *26

CM5P: *22 CM5P: *30
CM3P: *20 CM3P: *28
CM7P: *24 CM7P: *32

CM6P: *23 CM6P: *31

CM2P: *19 CM2P: *27
CM4P: *21 CM4P: *29
CM0P: *17 CM0P: *25

NOTE1: The cache memory module location *17 through *32 correspond to the CM
Location listed in Table 3.10-4 through Table 3.10-9.
Fig. 3.10-48 Inserting Location of the CM Module

INST03-10-870
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-880


Memory Module 
 Lever
Cut

Socket

Projection
inside the slot

Installation
 Position the cut of the memory module with the projection inside the slot, and place the memory module
on the socket.
 Hold both ends of the memory module by the fingers, and fit it into the socket.
 Make sure that the lever is firmly fitted in the memory module.

NOTICE: Do not put intense pressure on the CM Module to the extent that the PCB
greatly bends after the CM Module is secured with the levers in installation
procedure of the CM Module. The PCB may be damaged when intense
pressure is applied.

Memory Module Appearance

There are two types of memory modules. One has a heat spreader and the other has no heat spreaders.
Both memory modules can be used because they are compatible with each other.

Memory Module Memory Module

(with Heat Spreader) (without Heat Spreader)

Heat Spreader

Fig. 3.10-49 Insertion of Memory Module

INST03-10-880
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-890

10-3 Insert the PCB.

a. When you need to install Additional Cache Path Control Adapter (DKC-F810I-CPEX),
attach the dummy plate and fasten the screws.
When you do not need to install Additional Cache Path Control Adapter (DKC-F810I-
CPEX), go to Step b.
NOTE: Store the removed dummy plate as it is required when the Additional Cache Path
Control Adapter is removed.

NOTICE: Remove the dummy plate just before installing the PCB.
If the dummy plate is kept removed for a long time, the wind doesn’t flow
among installed PCBs, causing the PCBs’ temperature rise which may result
in temperature warning or temperature alarm.

b. Install the CM PCB and tighten the two screws.

NOTE: When inserting the CM PCB, be careful not to get cables caught on anything.
c. If the cables were disconnected in procedure 10-1 b, connect the cables to the CM PCB
after checking “3.1.7 Notes when connecting and disconnecting MFC cable” (INST03-01-
190).

Main Edge Connector

PCB NOTICE: • Check that the main edge connector of the PCB has
no deformation, damage or sticking of dust before
installing the PCB. (See INST03-01-80)
• When installing the PCB, hold the top and bottom of
the PCB with both hands, and insert it straight not to
contact the neighboring PCB.

Table 3.10-12 Location of the CM PCB

Cluster Box Slot No. Location No. Remarks
2 DKC-0 2CA CACHE-2CA
2CB CACHE-2CB
DKC-1 2CC CACHE-2CC
2CD CACHE-2CD

INST03-10-890
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-900

DKC

CM PCB

Screw
Lever

CL2 2Cx-0
CL2 2Cx-1

Screw
CL2 2Cx-2 Lever Screw

CL2 2Cx-3

Dummy Plate

Fig. 3.10-50 Installation of PCB

INST03-10-900
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-910

11. SVP post procedure on the Cluster 2.

(1)
After completing the additional
installation of the cache memory on the
cluster 2, select (CL) [OK] in response to
“Replace or insert the Cache Memory
PCB(s)(Memory) of cluster-2. When
completed, please press OK.”.

(2) <Cache CUDG executes>

“INLINE CUDG is now running...” is displayed.

(3)
“Changing the configuration date, for equipment of shared/cache memory...”
“Restoring the Cache Memory PCB...”
“Restoring the Shared Memory PCB...” is displayed.

(4) <End of system update processing>

“Renewal process has completed. Please
check storage system status.” is displayed
when recovery processing on all installed
components is completed. Select (CL)
[OK] in response to this message.

INST03-10-910
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-920

(5)
Execute an operation for backing up the
configuration information.
Prepare the removable media for backup
and insert the media.
Please select (CL) the [Refresh] button,
and update drive information.
Select (CL) the drive and the PC in which
the media was inserted. Select (CL) the
[OK] button.
NOTE: For the procedure of
backing up the configuration
information to a CD-R,
see page MICRO07-190.

(6)
When this procedure is completed, the message
“Please remove the Config media.” is displayed.
Remove the configuration information media,
select (CL) [OK].

INST03-10-920
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-10-930

(7)
After the procedure is completed, return
to ‘Install’.
Select (CL) [File]-[Exit].

(8) <Mode Change>

Change the mode to View Mode.

Return to the working table and do the rest of the work.

Non-Disruptive Installation: INST02-40

INST03-10-930
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11-10

3.11 Installation of Disk Adapter, Drive and DEV Interface Cable

(DKC-F810I-SCA/CC1/CC2/CC4/300KCM/600JCM/900JCM/1R2JCM/3R0H3M/4R0H3M/
400MCM/800MCM/1R6FM/3R2FM)

Table 3.11-1 Parts List

No. Model Number Part Name Part No. Quantity Remarks
1 DKC-F810I-SCA WP820-A 5552770-A 2 DKA
(To be continued)

INST03-11-10
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11-20

(Continued from the preceding page)

No. Model Number Part Name Part No. Quantity Remarks
2 DKC-F810I-CC1 DEV I/F Cable 5552754-A 8
Label (Address) 3287113-1 3
Label (Address) 2 3287144-1 3
Label (Protect) 3287450-1 6
3 DKC-F810I-CC2 DEV I/F Cable 5552755-A 8
Label (Address) 3287113-1 3
Label (Address) 2 3287144-1 3
Label (Protect) 3287450-1 6
4 DKC-F810I-CC4 DEV I/F Cable 5552756-A 8
Label (Address) 3287113-1 3
Label (Address) 2 3287144-1 3
Label (Protect) 3287450-1 6
Loop Cable Tie 5552567-1 8
(To be continued)

INST03-11-20
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11-30

(Continued from the preceding page)

No. Model Number Part Name Part No. Quantity Remarks
5 DKC-F810I-300KCM HDU800-300KCMSS 5552785-A 1
6 DKC-F810I-600JCM HDU800-600JCMSS 5552786-A 1
7 DKC-F810I-900JCM HDU800-900JCMSS 5552787-A 1
8 DKC-F810I-1R2JCM HDU800-1R2JCMSS 5552789-A 1
9 DKC-F810I-3R0H3M HDU800-3R0H3MSS 5552783-A 1
10 DKC-F810I-4R0H3M HDU800-4R0H3MSS 5552784-A 1
11 DKC-F810I-400MCM HDU800-400MCMSS 5552790-A 1
12 DKC-F810I-800MCM HDU800-800MCMSS 5552791-A 1
13 DKC-F810I-1R6FM HDU800-1R6FMSS 3286549-A 1
14 DKC-F810I-3R2FM HDU800-3R2FMSS 3286550-A 1

INST03-11-30
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11-40

Table 3.11-2 Working time

Number of change (set) Total (minutes)
DKA Installation 1 10
2 15
3 20
4 25

NOTE: For DKA installation, additional 3600 seconds (60 minutes) is necessary to newly route
cable(s) between drives.

INST03-11-40
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11-50

3.11.1 Flowchart
There are three cases ( to ) of these addition works as shown in the following table. Perform the
work referring to the flowchart of each work.

Case Option Installation Procedure Page

 When performing addition of the data/spare Drive INST03-11-60
(DKC-F810I-300KCM/600JCM/900JCM/1R2JCM/3R0H3M/
4R0H3M/400MCM/800MCM/1R6FM/3R2FM)
 When performing addition of the DKA and Device Interface Cable INST03-11-60
(DKC-F810I-SCA/CC1/CC2)
 When performing addition of the data/spare Drive and DEV INST03-11-70
interface cable that accompanies the addition of the DKU
(DKC-F810I-CC1/CC2/CC4/300KCM/600JCM/900JCM/1R2JCM/
3R0H3M/4R0H3M/400MCM/800MCM/1R6FM/3R2FM)
 When performing addition of the DKA and DEV interface cable that INST03-11-80
accompanies the addition of the DKU-00/10 (only hardware
procedure)
(DKC-F810I-SCA/CC1/CC2)

INST03-11-50
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11-60

 When performing addition of the data/spare Drive

------------------------------------------------------------------------------[INST03-11A-10 through 770]

1. Setting up the New Device Structure Information


2. SVP pre procedure

3. Installation Procedure of Drive

4. SVP post procedure

 When performing addition of the DKA and Device Interface Cable

------------------------------------------------------------------------------ [INST03-11B-10 through 670]

1. Attachment of Location Labels


2. Setting up the New Device Structure Information

3. SVP pre procedure (cluster 1)

4. Installation Procedure of Disk Adapter for cluster 1

5. Attachment Procedure of Device Interface Cable for Cluster 1 (DKC-F810I-CC1/CC2)

6. SVP post procedure (cluster 1)

7. SVP pre procedure (cluster 2)

8. Installation Procedure of Disk Adapter for cluster 2

9. Attachment Procedure of Device Interface Cable for Cluster 2 (DKC-F810I-CC1/CC2)

10. SVP post procedure (cluster 2)

INST03-11-60
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11-70

 When performing addition of the data/spare Drive and Device Interface Cable that accompanies
the addition of the DKU
---------------------------------------------------------------------------- [INST03-11C-10 through 1450]

1. Storage system Configurations and Required I/F Cable Options --- INST03-11C-20

2. Attachment of Location Labels for Device Interface Cable (DKC-F810I-CC1/CC2/CC4)
--- INST03-11C-120

3. Setting up the New Device Structure Information --- INST03-11C-150

4. Installation Procedure of drive --- INST03-11C-340

5. Installation Procedure of Device Interface Cable CC1 (DKC-F810I-CC1) --- INST03-11C-910

6. Installation Procedure of Device Interface Cable CC2 (DKC-F810I-CC2) --- INST03-11C-960

7. Installation Procedure of Device Interface Cable CC4 (DKC-F810I-CC4) --- INST03-11C-1140

8. SVP post procedure --- INST03-11C-1440

INST03-11-70
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11-80

 When performing addition of the DKA and Device Interface Cable that accompanies the addition
of the DKU-00/10
------------------------------------------------------------------------------[INST03-11D-10 through 460]
In the case of Standard Model

1. Installation Procedure of Disk Adapter


2. Attachment of Device Interface Cable (CC2)

3. Attachment of Device Interface Cable (CC1)

4. Attachment of Cables

In the case of High-performance Model

1. Installation Procedure of Disk Adapter


2. Attachment of Device Interface Cable (CC2)

3. Attachment of Cables

INST03-11-80
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-10

3.11.2 When performing addition of the data/spare Drive

(DKC-F810I-300KCM/600JCM/900JCM/1R2JCM/3R0H3M/4R0H3M/400MCM/800MCM/
1R6FM/3R2FM)

NOTICE: If No Charging of FMD (SIM = 50EXYY) occurs in installation of a FMD, the

FMD ACTIVE LED will change to low-speed blinking. In this case, it takes 90
minutes at most for the FMD ACTIVE LED to go out and for the battery in the
FMD to be fully charged.

1. Setting up the New Device Structure Information

(1) <Mode Change>
Change the mode to Modify Mode.
Select (CL) [Install].

(2) <Start the ‘Menu Dialog’ screen>

Select (CL) [Change Configuration].

(3) <Start Device Structure Setup screen>

Select (CL) [Installation] in the ‘Menu Dialog’
dialog box and select (CL) [OK].

INST03-11A-10
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-20

(4) <Select a changed part>

Select (CL) [ECC group + LDEV], and select
(CL) [OK].

(5) <DKC Configuration screen>

In the ‘DKC Configuration’ screen, select
(CL) [>>Next].
Go to Step (6).

NOTE: There may be a case where an

addition of the SM is required to add
the CU.

(6) <DKU Equipment Configuration screen>

Select (CL) [>>Next] in the ‘DKU Equipment
Configuration’ screen.
Go to Step (7).

INST03-11A-20
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-30

(7) <Physical Device Configuration screen>

Define the drive configuration according to the
‘Physical Device Configuration’ screen.
Detailed procedure is shown below.
[Set...]: Defines the parity group or spare
disk.
Go to Step (8).
[Clear...]: Cancels the setting of the B4.
After setting up all items, select (CL)
[>>Next].
Go to Step (9).

Selecting (CL) [Before<<] returns to Step (6).

• Relation between B4 and HDU Location (Refer to LOC02-40 ~ 80 for Location.)

B4 Location B4 Location
DKU HDU DKU HDU
1st DKU-00 HDU-000, 001, 002, 003 13th DKU-03 HDU-030, 031, 032, 033
2nd DKU-00 HDU-004, 005, 006, 007 14th DKU-03 HDU-034, 035, 036, 037
3rd DKU-10 HDU-100, 101, 102, 103 15th DKU-13 HDU-130, 131, 132, 133
4th DKU-10 HDU-104, 105, 106, 107 16th DKU-13 HDU-134, 135, 136, 137
5th DKU-01 HDU-010, 011, 012, 013 17th DKU-04 HDU-040, 041, 042, 043
6th DKU-01 HDU-014, 015, 016, 017 18th DKU-04 HDU-044, 045, 046, 047
7th DKU-11 HDU-110, 111, 112, 113 19th DKU-14 HDU-140, 141, 142, 143
8th DKU-11 HDU-114, 115, 116, 117 20th DKU-14 HDU-144, 145, 146, 147
9th DKU-02 HDU-020, 021, 022, 023 21st DKU-05 HDU-050, 051, 052, 053
10th DKU-02 HDU-024, 025, 026, 027 22nd DKU-05 HDU-054, 055, 056, 057
11th DKU-12 HDU-120, 121, 122, 123 23rd DKU-15 HDU-150, 151, 152, 153
12th DKU-12 HDU-124, 125, 126, 127 24th DKU-15 HDU-154, 155, 156, 157

INST03-11A-30
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-40

(8) <Define Parity Group>

‘Parity Group Configuration’ dialog box is
displayed.
[Group...]: Defines the parity group.
See Step (8)-1.
[Spare...]: Defines the spare drive.
See Step (8)-2.
[Delete]: Deletes the added parity group or
spare drive.
Grp*: A parity group where RAID
Concatenation is installed.

NOTE: If you want to set any Spare Drives in

B4, please define the Spare Drive first.

After setting up all items, select (CL) [OK]. Go back to Step (7).

INST03-11A-40
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-50

(8)-1
Define the RAID Level, the Drive Type, and
the Number of Group in the ‘Parity Group’
dialog box.
Then select (CL) [OK]. Go back to Step (8).

(8)-2
Define the Drive Type and the Number of
Spare in the ‘Spare’ dialog box.
Then select (CL) [OK].
Go back to Step (8).

INST03-11A-50
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-60

(9) <Define Device Emulation>

After setting up all items corresponding (9)-1 to (9)-3 for definition of Device Emulation, select
(CL) [>>Next].
Selecting (CL) [Before<<] returns you to the previous screen.
In the case of only spare drive installation, select (CL) [>>Next]. Go to Step (10).
• If defining Device Emulation, go to Step (9)-1.
• If setting RAID concatenation, go to Step (9)-2.
• If defining of Customized Volume Size (CVS), go to Step (9)-3.

(9)-1 <Define Device Emulation>

Select (CL) parity group and select (CL)
[Set...]. Go to Step (9)-1-1.

(CVS): A parity group where CVS is

installed.
Grp*: A parity group where RAID
Concatenation is installed.

(9)-1-1
After setting up all items in the ‘Device Emulation
Type Define’ dialog box, select (CL) [OK].
Go back to Step (9).

Selecting (CL) [Cancel] returns you to Step (9)-1

without reflecting the setting items.
NOTE: OPEN-V is a recommended OPEN volume.
To set other than OPEN-V, please select
“Except OPEN-V”.
NOTE: “0” can be set to the value of Number of
LDEVs for all the emulation types.
If you don’t know the LDEV size you will use, set “0”. You can save time by setting “0”
because LDEV format will not run.
When you set “0”, please make LDEVs later using the CVS function.
NOTE: If 3390-A is selected, a 3390-A volume whose capacity is as large as that of standard
capacity of the specified emulation type can be created by specifying (3390-3 size),
(3390-9 size), (3390-L size), or (3390-M size) in the “Number of LDEVs”. If a parity
group consists of drives with 1TB or larger is specified, only (3390-M size) can be
selected in the “Number of LDEVs”.

INST03-11A-60
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-70

(9)-2 <Setting RAID concatenation>

Select (CL) [Concatenate...].
When you do not perform RAID concatenation, go back to Step (9).

(9)-2-1
Parity groups to which the RAID
concatenation can be applied are displayed in
the Parity group List.
Select (CL) parity groups to which you want to
apply the RAID concatenation and press (CL)
the [>>] button. Go to Step (9)-2-1.

NOTE: Only the parity groups, which have

been added and to which the RAID
concatenation can be applied are
displayed in the Parity group List.

(9)-2-2
The selected parity groups are registered in the
Concatenate Parity group List. Then press
(CL) the [Concatenate] button. Go to Step
(9)-2-3.

NOTE: The [Concatenate] button cannot be

pressed if the concatenation does not
meet a condition of the RAID
concatenation. Adjust the number of
the parity groups in the Concatenate
Parity group List.

INST03-11A-70
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-80

(9)-2-3
When the RAID concatenation is completed,
“(Concatenation)” is displayed in the Parity
group List.Selecting the “(Concatenation)”
displays the concatenated parity groups in the
Concatenation List.
Selecting (CL) [Clear] cancels the RAID
concatenation.

When all the settings of the RAID

concatenation are completed, select (CL)
[OK].
Go back to Step (9).
Selecting (CL) [Cancel] returns the routine to Step (9).

(9)-3 <Defining of Customized Volume Size (CVS)>

Select (CL) a parity group for which the LDEV
emulation type and the number of LDEVs
have been set on the ‘Device Emulation
Configuration’ screen and select (CL)
[Detail...].
When defining other than OPEN-V, go to Step
(9)-3-1.
When defining OPEN-V, go to Step (9)-3-2.

When you do not perform the CVS, go back to

Step (9).

INST03-11A-80
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-90

(9)-3-1 <Definition other than OPEN-V>

A volume other than OPEN-V can be defined
in the ‘Customized Volume Size Define’
screen.
• Set of a CVS volume
Perform  Delete of the Volume and  Add
of the Volume.

 Delete of the Volume

A volume can be deleted by selecting (CL)
the volume from the LDEV list box and
selecting (CL) [Delete].
 Add of the Volume
A volume can be added by entering the LDEV emulation type and the user size
(Mbyte/Blocks or Cylinder) of the customized volume (CV) and selecting [Add].
(It can be added in the optional space “empty” by selecting (CL) “empty” from the LDEV list
box.)
The two or more CVs can be registered when the operation above is performed repeatedly.

The boundary correction existence is specifiable with “Offset Boundary”.

(When a volume for mainframe host is selected, it is not possible to select it.)

Adding or deleting operation can be done for any number of times. The last setting is reflected by
selecting (CL) [OK].

NOTE: The two or more volumes can be selected and deleted.

The routine returns to the preceding window by selecting (CL) [Cancel].

The routine returns to the preceding window and the change is reflected by selecting (CL) [OK].

INST03-11A-90
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-100

(9)-3-2 <Definition of OPEN-V>

OPEN-V can be defined in the ‘Variable
Volume Size Define’ screen.
• Set of a CVS volume
Perform  Delete of the Volume and  Add
of the Volume.

 Delete of the Volume

The volume can be deleted by selecting
(CL) [Delete] in the state (CL) of selecting (CL) the volume in the LDEV list box.
All the volumes in the LDEV list box can be deleted by selecting (CL) [Clear].
 Add of the Volume
It can be added by selecting (CL) Variable Volume Size from the status “select (CL) ‘empty’”
or “no selection” in the LDEV list box and selecting (CL) [Add].

Adding or deleting operation can be done for any number of times. The last setting is reflected by
selecting (CL) [OK].

NOTE: The two or more volumes can be selected and deleted.

• Variable Volume Size

“Specify size & number” : Defines the specified number of the specified user size.
• Offset Boundary : The boundary correction existence is specified.
• Capacity Unit
“MByte” : Makes data displayed or entered by [MByte].
“Cylinder” : Makes data displayed or entered by the [Cylinder].
“Blocks” : Makes data displayed or entered by the [Blocks].
• asst. : When Path/pool-VOL is defined, “+” is displayed.
NOTE: Even if the journal volume is defined, “+” is not
displayed.
[Clear] : Deletes all the volumes.
[Delete] : Deletes all the selected volumes.
[Add] : Adds volumes.
[Cancel] : Invalidates the setting, and returns to the preceding window.
[OK] : Confirms the setting, and returns to the preceding window.

INST03-11A-100
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-110

(10) <Define LDEV ID>

(10)-1 <Definition Screen for LDEV ID>
Select (CL) the parity group to be defined and
select (CL) a function from the [LDEV ID] list
box.
[Linear...]: LDEV ID is assigned to LDEV in
the order of parity groups. See Step
(10)-3.
[Disperse...]: LDEV is assigned discretely in the
order of parity groups. See Step
(10)-3.
[Detail...]: A screen to define LDEV in detail
is displayed. See Step (10)-2.
(When plural groups are selected
(CL), it is invalid.)
[Clear]: Select (CL) [Clear] to delete.
Grp*: The top parity group where RAID Concatenation is installed.
Status: Status of LDEV ID.
 “Complete” : LDEV ID is assigned.
 “-------” : LDEV ID is not assigned.
 “Error” : Invalid LDEV ID is assigned.

After setting up all items, select [Detail...] to confirm the items that have been setup, and select
(CL) [>>Next]. Go to Step (11).

(10)-2 <Detailed Definition Screen for LDEV ID>

LDEV ID is defined in detail for each LDEV
in the parity group.
Select (CL) LDEV from the list box and select
(CL) [Change...].
The screen for LDEV ID input is displayed.
After setting, select (CL) [OK]. Return to Step
(10)-1.
• “-----” is displayed in the CU area and the ID
area for the LDEV to which LDEV ID is not
assigned.
NOTE: In the case of a RAID Concatenation
Group, LDEV of the parity group
selected by the “Grp List” is displayed.

INST03-11A-110
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-120

(10)-3 <Input LDEV ID>

Select LDKC in the LDKC pull down menu.
Select CU in the CU pull down menu.
The status of usage of ID in the CU is displayed in
the LDEV ID panel.
White disk of panel: not used
Patterned disk of panel: using
Input LDEV ID you want to set or the head LDEV
ID in the ID Edit box.
After setting, select (CL) [OK].
Go back to Step (10)-1.
NOTE: The definition range (terminal) is decided
with LDEV Range.
For example, if LEDV Range is defined as
7F, LDEV ID is assigned only within the range of 00 to 7F.

(11) <Define SSID>

To define SSID, select (CL) the item from the list box
and select (CL) [SS ID...].
See Step (11)-1.

After setting, select (CL) [>>Next].

Go to Step (12).

(11)-1 Define SSID and select (CL) [OK].

Go back to Step (11).

INST03-11A-120
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-130

(12) <Define LDEV Management MPB>

In the ‘LDEV Management MPB
Configuration’ screen, select (CL) [Change
MPB].
Go to Step (12)-1.

After the setting is completed, select (CL)

[>>Next].
Go to Step (13).

(12)-1 <Define Management MPB>

Define Management MPB and select (CL) [OK].
Go back to Step (12).

INST03-11A-130
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-140

(13) <Selection of format>

Select (CL) [Yes] in response to “Do you want
to format logical devices by Quick Format?”
when you execute Quick Format.
When [No] is selected (CL), usual LDEV
Format is executed.

NOTE: Next, Quick Format cannot be

executed in the shown volume.
• external volume
• Volumes whose access attribute is not Read/Write
• Pool volumes (pool-VOLs)
• Journal volumes

(14) <Wear a wrist strap>

Select (CL) [OK] in response to “To prevent
serious failures caused by the static electrical
charge, be sure to wear a wrist strap on your
wrist and connect the earth clip attached on the
other side of the wrist strap to the chassis
frame (metal part) before starting operation.”.

(14)-1 <Confirm wearing wrist strap>

In response to a message, “Did you put on a
wrist strap on your wrist?”.
Select [Yes] when wrist strap is on your wrist.
Select [No] when there is no wrist strap on your
wrist.
When [No] is selected (CL), to to Step (14)-2.

(14)-2
In response to a message, “This operation
cannot be excuted, because the wrist strap has
not been worn. Do you want to stop this
process?
[Yes]: This processing will be stopped.
[No]: This confirming message will appear.”
When [Yes] is selected (CL), the routine is
returned to Step (2) on page INST03-11A-10.
When [No] is selected (CL), returned to Step (14).

INST03-11A-140
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-150

(15) <Start installation>

Select (CL) [Yes] in response to “After you
select [Yes], you cannot cancel this operation.
Are you sure you want to continue this
operation? (Note) Do not insert the
components for upgrading the system at this
time.”.

When [No] is selected (CL), returns to

INST03-11A-10 Step (2).

(16) <Download microprogram>

Microprograms are automatically downloaded for each processor.

(17) <Install DKA>

“Upgrading of the DKA...”

INST03-11A-150
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-160

2. SVP pre procedure

(1) <Notes when insert of PDEV>
“Do not insert multiple PDEV at the same
time. Insert PDEV one by one with an interval
of a second or more.” is displayed.
Select (CL) [OK].

(2) <Check that hardware components are installed>

At this point refrain from pressing the [OK]
button.
“Insert the PDEV on the storage system. Select
[OK] when the installation has completed.” is
displayed.

INST03-11A-160
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-170

3. Installation Procedure of drive

3-1 Confirmation of position to install drive
(i) RAID5 (3D+1P) / RAID1 (2D+2D), UBX (DKU for 3.5 inch Drive)
Relations between the installation locations of the RAID groups and the RAID group
numbers set through the SVP are shown in Table 3.11.2-1.

Table 3.11.2-1 Relation between drives installation order and RAID group number
(3D+1P/2D+2D, UBX) (1/2)
DKU-00 DKU-01 DKU-02 DKU-03 DKU-04 DKU-05
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
001 1-1 025 5-1 049 9-1 073 13-1 097 17-1 121 21-1
002 2-1 026 6-1 050 10-1 074 14-1 098 18-1 122 22-1
003 1-2 027 5-2 051 9-2 075 13-2 099 17-2 123 21-2
004 2-2 028 6-2 052 10-2 076 14-2 100 18-2 124 22-2
005 1-3 029 5-3 053 9-3 077 13-3 101 17-3 125 21-3
006 2-3 030 6-3 054 10-3 078 14-3 102 18-3 126 22-3
007 1-4 031 5-4 055 9-4 079 13-4 103 17-4 127 21-4
008 2-4 032 6-4 056 10-4 080 14-4 104 18-4 128 22-4
009 1-5 033 5-5 057 9-5 081 13-5 105 17-5 129 21-5
010 2-5 034 6-5 058 10-5 082 14-5 106 18-5 130 22-5
011 1-6 035 5-6 059 9-6 083 13-6 107 17-6 131 21-6
012 2-6 036 6-6 060 10-6 084 14-6 108 18-6 132 22-6
013 1-7 037 5-7 061 9-7 085 13-7 109 17-7 133 21-7
014 2-7 038 6-7 062 10-7 086 14-7 110 18-7 134 22-7
015 1-8 039 5-8 063 9-8 087 13-8 111 17-8 135 21-8
016 2-8 040 6-8 064 10-8 088 14-8 112 18-8 136 22-8
017 1-9 041 5-9 065 9-9 089 13-9 113 17-9 137 21-9
018 2-9 042 6-9 066 10-9 090 14-9 114 18-9 138 22-9
019 1-10 043 5-10 067 9-10 091 13-10 115 17-10 139 21-10
020 2-10 044 6-10 068 10-10 092 14-10 116 18-10 140 22-10
021 1-11 045 5-11 069 9-11 093 13-11 117 17-11 141 21-11
022 2-11 046 6-11 070 10-11 094 14-11 118 18-11 142 22-11
023 1-12 047 5-12 071 9-12 095 13-12 119 17-12 143 21-12
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1
024 2-12 048 6-12 072 10-12 096 14-12 120 18-12 144 22-12
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

INST03-11A-170
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-180

Table 3.11.2-1 Relation between drives installation order and RAID group number
(3D+1P/2D+2D, UBX) (2/2)
DKU-10 DKU-11 DKU-12 DKU-13 DKU-14 DKU-15
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
145 3-1 169 7-1 193 11-1 217 15-1 241 19-1 265 23-1
146 4-1 170 8-1 194 12-1 218 16-1 242 20-1 266 24-1
147 3-2 171 7-2 195 11-2 219 15-2 243 19-2 267 23-2
148 4-2 172 8-2 196 12-2 220 16-2 244 20-2 268 24-2
149 3-3 173 7-3 197 11-3 221 15-3 245 19-3 269 23-3
150 4-3 174 8-3 198 12-3 222 16-3 246 20-3 270 24-3
151 3-4 175 7-4 199 11-4 223 15-4 247 19-4 271 23-4
152 4-4 176 8-4 200 12-4 224 16-4 248 20-4 272 24-4
153 3-5 177 7-5 201 11-5 225 15-5 249 19-5 273 23-5
154 4-5 178 8-5 202 12-5 226 16-5 250 20-5 274 24-5
155 3-6 179 7-6 203 11-6 227 15-6 251 19-6 275 23-6
156 4-6 180 8-6 204 12-6 228 16-6 252 20-6 276 24-6
157 3-7 181 7-7 205 11-7 229 15-7 253 19-7 277 23-7
158 4-7 182 8-7 206 12-7 230 16-7 254 20-7 278 24-7
159 3-8 183 7-8 207 11-8 231 15-8 255 19-8 279 23-8
160 4-8 184 8-8 208 12-8 232 16-8 256 20-8 280 24-8
161 3-9 185 7-9 209 11-9 233 15-9 257 19-9 281 23-9
162 4-9 186 8-9 210 12-9 234 16-9 258 20-9 282 24-9
163 3-10 187 7-10 211 11-10 235 15-10 259 19-10 283 23-10
164 4-10 188 8-10 212 12-10 236 16-10 260 20-10 284 24-10
165 3-11 189 7-11 213 11-11 237 15-11 261 19-11 285 23-11
166 4-11 190 8-11 214 12-11 238 16-11 262 20-11 286 24-11
167 3-12 191 7-12 215 11-12 239 15-12 263 19-12 287 23-12
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1
168 4-12 192 8-12 216 12-12 240 16-12 264 20-12 288 24-12
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

INST03-11A-180
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-190

(1) Make sure of the location where the RAID group is installed and that where the drive is to be
added.
No. Model Number Model Name Remarks
1 DKC-F810I-3R0H3M/4R0H3M × 4 LFF Disk Drive

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-11 DKU-01
186 188 190 192*1 042 044 046 048*1
178 180 182 184 034 036 038 040
170 172 174 176 026 028 030 032
185 187 189 191*1 041 043 045 047*1
177 179 181 183 033 035 037 039
169 171 173 175 025 027 029 031
186 188 190 192*1 042 044 046 048*1
178 180 182 184 034 036 038 040
170 172 174 176 026 028 030 032
185 187 189 191*1 041 043 045 047*1
177 179 181 183 033 035 037 039
169 171 173 175 025 027 029 031
186 188 190 192*1 042 044 046 048*1
178 180 182 184 034 036 038 040
170 172 174 176 026 028 030 032
185 187 189 191*1 041 043 045 047*1
177 179 181 183 033 035 037 039
169 171 173 175 025 027 029 031
186 188 190 192*1 042 044 046 048*1
178 180 182 184 034 036 038 040
170 172 174 176 026 028 030 032
185 187 189 191*1 041 043 045 047*1
177 179 181 183 033 035 037 039
169 171 173 175 025 027 029 031
DKU-10 DKU-00
162 164 166 168*1 018 020 022 024*1
154 156 158 160 010 012 014 016
146 148 150 152 002 004 006 008
161 163 165 167*1 017 019 021 023*1
153 155 157 159 009 011 013 015
145 147 149 151 001 003 005 007
162 164 166 168*1 018 020 022 024*1
154 156 158 160 010 012 014 016
146 148 150 152 002 004 006 008
161 163 165 167*1 017 019 021 023*1
153 155 157 159 009 011 013 015
145 147 149 151 001 003 005 007
162 164 166 168*1 018 020 022 024*1
154 156 158 160 010 012 014 016
146 148 150 152 002 004 006 008
161 163 165 167*1 017 019 021 023*1
153 155 157 159 009 011 013 015
145 147 149 151 001 003 005 007
162 164 166 168*1 018 020 022 024*1
154 156 158 160 010 012 014 016
146 148 150 152 002 004 006 008
161 163 165 167*1 017 019 021 023*1
153 155 157 159 009 011 013 015
145 147 149 151 001 003 005 007
*1: A data or
DKC-1 DKC-0 spare disk
is to be
installed.

Front View Front View

Fig. 3.11.2-1 (3D+1P/2D+2D) Data Drive/Parity Drive Expansion Sequence (1/3)

The relationship between drives installation order and RAID group number is shown in the Table
3.11.2-1.
INST03-11A-190
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-200

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-13 DKU-03
234 236 238 240*1 090 092 094 096*1
226 228 230 232 082 084 086 088
218 220 222 224 074 076 078 080
233 235 237 239*1 089 091 093 095*1
225 227 229 231 081 083 085 087
217 219 221 223 073 075 077 079
234 236 238 240*1 090 092 094 096*1
226 228 230 232 082 084 086 088
218 220 222 224 074 076 078 080
233 235 237 239*1 089 091 093 095*1
225 227 229 231 081 083 085 087
217 219 221 223 073 075 077 079
234 236 238 240*1 090 092 094 096*1
226 228 230 232 082 084 086 088
218 220 222 224 074 076 078 080
233 235 237 239*1 089 091 093 095*1
225 227 229 231 081 083 085 087
217 219 221 223 073 075 077 079
234 236 238 240*1 090 092 094 096*1
226 228 230 232 082 084 086 088
218 220 222 224 074 076 078 080
233 235 237 239*1 089 091 093 095*1
225 227 229 231 081 083 085 087
217 219 221 223 073 075 077 079
DKU-12 DKU-02
210 212 214 216*1 066 068 070 072*1
202 204 206 208 058 060 062 064
194 196 198 200 050 052 054 056
209 211 213 215*1 065 067 069 071*1
201 203 205 207 057 059 061 063
193 195 197 199 049 051 053 055
210 212 214 216*1 066 068 070 072*1
202 204 206 208 058 060 062 064
194 196 198 200 050 052 054 056
209 211 213 215*1 065 067 069 071*1
201 203 205 207 057 059 061 063
193 195 197 199 049 051 053 055
210 212 214 216*1 066 068 070 072*1
202 204 206 208 058 060 062 064
194 196 198 200 050 052 054 056
209 211 213 215*1 065 067 069 071*1
201 203 205 207 057 059 061 063
193 195 197 199 049 051 053 055
210 212 214 216*1 066 068 070 072*1
*1: A data or
202 204 206 208 058 060 062 064 spare disk
194 196 198 200 050 052 054 056
is to be
209 211 213 215*1 065 067 069 071*1
201 203 205 207 057 059 061 063 installed.
193 195 197 199 049 051 053 055

Front View Front View

Fig. 3.11.2-1 (3D+1P/2D+2D) Data Drive/Parity Drive Expansion Sequence (2/3)

The relationship between drives installation order and RAID group number is shown in the Table
3.11.2-1.

INST03-11A-200
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-210

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-15 DKU-05
282 284 286 288*1 138 140 142 144*1
274 276 278 280 130 132 134 136
266 268 270 272 122 124 126 128
281 283 285 287*1 137 139 141 143*1
273 275 277 279 129 131 133 135
265 267 269 271 121 123 125 127
282 284 286 288*1 138 140 142 144*1
274 276 278 280 130 132 134 136
266 268 270 272 122 124 126 128
281 283 285 287*1 137 139 141 143*1
273 275 277 279 129 131 133 135
265 267 269 271 121 123 125 127
282 284 286 288*1 138 140 142 144*1
274 276 278 280 130 132 134 136
266 268 270 272 122 124 126 128
281 283 285 287*1 137 139 141 143*1
273 275 277 279 129 131 133 135
265 267 269 271 121 123 125 127
282 284 286 288*1 138 140 142 144*1
274 276 278 280 130 132 134 136
266 268 270 272 122 124 126 128
281 283 285 287*1 137 139 141 143*1
273 275 277 279 129 131 133 135
265 267 269 271 121 123 125 127
DKU-14 DKU-04
258 260 262 264*1 114 116 118 120*1
250 252 254 256 106 108 110 112
242 244 246 248 098 100 102 104
257 259 261 263*1 113 115 117 119*1
249 251 253 255 105 107 109 111
241 243 245 247 097 099 101 103
258 260 262 264*1 114 116 118 120*1
250 252 254 256 106 108 110 112
242 244 246 248 098 100 102 104
257 259 261 263*1 113 115 117 119*1
249 251 253 255 105 107 109 111
241 243 245 247 097 099 101 103
258 260 262 264*1 114 116 118 120*1
250 252 254 256 106 108 110 112
242 244 246 248 098 100 102 104
257 259 261 263*1 113 115 117 119*1
249 251 253 255 105 107 109 111
241 243 245 247 097 099 101 103
258 260 262 264*1 114 116 118 120*1
*1: A data or
250 252 254 256 106 108 110 112 spare disk
242 244 246 248 098 100 102 104
is to be
257 259 261 263*1 113 115 117 119*1
249 251 253 255 105 107 109 111 installed.
241 243 245 247 097 099 101 103

Front View Front View

Fig. 3.11.2-1 (3D+1P/2D+2D) Data Drive/Parity Drive Expansion Sequence (3/3)

The relationship between drives installation order and RAID group number is shown in the Table
3.11.2-1.

INST03-11A-210
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-220

(ii) RAID5 (3D+1P) / RAID1 (2D+2D), SBX (DKU for 2.5 inch Drive)
Relations between the installation locations of the RAID groups and the RAID group
numbers set through the SVP are shown in Table 3.11.2-2.

Table 3.11.2-2 Relation between drives installation order and RAID group number
(3D+1P/2D+2D, SBX) (1/4)
DKU-00 DKU-01 DKU-02
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
001 1-1 025 1-13 049 5-1 073 5-13 097 9-1 121 9-13
002 2-1 026 2-13 050 6-1 074 6-13 098 10-1 122 10-13
003 1-2 027 1-14 051 5-2 075 5-14 099 9-2 123 9-14
004 2-2 028 2-14 052 6-2 076 6-14 100 10-2 124 10-14
005 1-3 029 1-15 053 5-3 077 5-15 101 9-3 125 9-15
006 2-3 030 2-15 054 6-3 078 6-15 102 10-3 126 10-15
007 1-4 031 1-16 055 5-4 079 5-16 103 9-4 127 9-16
008 2-4 032 2-16 056 6-4 080 6-16 104 10-4 128 10-16
009 1-5 033 1-17 057 5-5 081 5-17 105 9-5 129 9-17
010 2-5 034 2-17 058 6-5 082 6-17 106 10-5 130 10-17
011 1-6 035 1-18 059 5-6 083 5-18 107 9-6 131 9-18
012 2-6 036 2-18 060 6-6 084 6-18 108 10-6 132 10-18
013 1-7 037 1-19 061 5-7 085 5-19 109 9-7 133 9-19
014 2-7 038 2-19 062 6-7 086 6-19 110 10-7 134 10-19
015 1-8 039 1-20 063 5-8 087 5-20 111 9-8 135 9-20
016 2-8 040 2-20 064 6-8 088 6-20 112 10-8 136 10-20
017 1-9 041 1-21 065 5-9 089 5-21 113 9-9 137 9-21
018 2-9 042 2-21 066 6-9 090 6-21 114 10-9 138 10-21
019 1-10 043 1-22 067 5-10 091 5-22 115 9-10 139 9-22
020 2-10 044 2-22 068 6-10 092 6-22 116 10-10 140 10-22
021 1-11 045 1-23 069 5-11 093 5-23 117 9-11 141 9-23
022 2-11 046 2-23 070 6-11 094 6-23 118 10-11 142 10-23
023 1-12 047 1-24 071 5-12 095 5-24 119 9-12 143 9-24
Spare*1 Spare*1 Spare*1
024 2-12 048 2-24 072 6-12 096 6-24 120 10-12 144 10-24
Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

INST03-11A-220
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-230

Table 3.11.2-2 Relation between drives installation order and RAID group number
(3D+1P/2D+2D, SBX) (2/4)
DKU-03 DKU-04 DKU-05
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
145 13-1 169 13-13 193 17-1 217 17-13 241 21-1 265 21-13
146 14-1 170 14-13 194 18-1 218 18-13 242 22-1 266 22-13
147 13-2 171 13-14 195 17-2 219 17-14 243 21-2 267 21-14
148 14-2 172 14-14 196 18-2 220 18-14 244 22-2 268 22-14
149 13-3 173 13-15 197 17-3 221 17-15 245 21-3 269 21-15
150 14-3 174 14-15 198 18-3 222 18-15 246 22-3 270 22-15
151 13-4 175 13-16 199 17-4 223 17-16 247 21-4 271 21-16
152 14-4 176 14-16 200 18-4 224 18-16 248 22-4 272 22-16
153 13-5 177 13-17 201 17-5 225 17-17 249 21-5 273 21-17
154 14-5 178 14-17 202 18-5 226 18-17 250 22-5 274 22-17
155 13-6 179 13-18 203 17-6 227 17-18 251 21-6 275 21-18
156 14-6 180 14-18 204 18-6 228 18-18 252 22-6 276 22-18
157 13-7 181 13-19 205 17-7 229 17-19 253 21-7 277 21-19
158 14-7 182 14-19 206 18-7 230 18-19 254 22-7 278 22-19
159 13-8 183 13-20 207 17-8 231 17-20 255 21-8 279 21-20
160 14-8 184 14-20 208 18-8 232 18-20 256 22-8 280 22-20
161 13-9 185 13-21 209 17-9 233 17-21 257 21-9 281 21-21
162 14-9 186 14-21 210 18-9 234 18-21 258 22-9 282 22-21
163 13-10 187 13-22 211 17-10 235 17-22 259 21-10 283 21-22
164 14-10 188 14-22 212 18-10 236 18-22 260 22-10 284 22-22
165 13-11 189 13-23 213 17-11 237 17-23 261 21-11 285 21-23
166 14-11 190 14-23 214 18-11 238 18-23 262 22-11 286 22-23
167 13-12 191 13-24 215 17-12 239 17-24 263 21-12 287 21-24
Spare*1 Spare*1 Spare*1
168 14-12 192 14-24 216 18-12 240 18-24 264 22-12 288 22-24
Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

INST03-11A-230
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-240

Table 3.11.2-2 Relation between drives installation order and RAID group number
(3D+1P/2D+2D, SBX) (3/4)
DKU-10 DKU-11 DKU-12
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
289 3-1 313 3-13 337 7-1 361 7-13 385 11-1 409 11-13
290 4-1 314 4-13 338 8-1 362 8-13 386 12-1 410 12-13
291 3-2 315 3-14 339 7-2 363 7-14 387 11-2 411 11-14
292 4-2 316 4-14 340 8-2 364 8-14 388 12-2 412 12-14
293 3-3 317 3-15 341 7-3 365 7-15 389 11-3 413 11-15
294 4-3 318 4-15 342 8-3 366 8-15 390 12-3 414 12-15
295 3-4 319 3-16 343 7-4 367 7-16 391 11-4 415 11-16
296 4-4 320 4-16 344 8-4 368 8-16 392 12-4 416 12-16
297 3-5 321 3-17 345 7-5 369 7-17 393 11-5 417 11-17
298 4-5 322 4-17 346 8-5 370 8-17 394 12-5 418 12-17
299 3-6 323 3-18 347 7-6 371 7-18 395 11-6 419 11-18
300 4-6 324 4-18 348 8-6 372 8-18 396 12-6 420 12-18
301 3-7 325 3-19 349 7-7 373 7-19 397 11-7 421 11-19
302 4-7 326 4-19 350 8-7 374 8-19 398 12-7 422 12-19
303 3-8 327 3-20 351 7-8 375 7-20 399 11-8 423 11-20
304 4-8 328 4-20 352 8-8 376 8-20 400 12-8 424 12-20
305 3-9 329 3-21 353 7-9 377 7-21 401 11-9 425 11-21
306 4-9 330 4-21 354 8-9 378 8-21 402 12-9 426 12-21
307 3-10 331 3-22 355 7-10 379 7-22 403 11-10 427 11-22
308 4-10 332 4-22 356 8-10 380 8-22 404 12-10 428 12-22
309 3-11 333 3-23 357 7-11 381 7-23 405 11-11 429 11-23
310 4-11 334 4-23 358 8-11 382 8-23 406 12-11 430 12-23
311 3-12 335 3-24 359 7-12 383 7-24 407 11-12 431 11-24
Spare*1 Spare*1 Spare*1
312 4-12 336 4-24 360 8-12 384 8-24 408 12-12 432 12-24
Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

INST03-11A-240
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-250

Table 3.11.2-2 Relation between drives installation order and RAID group number
(3D+1P/2D+2D, SBX) (4/4)
DKU-13 DKU-14 DKU-15
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
433 15-1 457 15-13 481 19-1 505 19-13 529 23-1 553 23-13
434 16-1 458 16-13 482 20-1 506 20-13 530 24-1 554 24-13
435 15-2 459 15-14 483 19-2 507 19-14 531 23-2 555 23-14
436 16-2 460 16-14 484 20-2 508 20-14 532 24-2 556 24-14
437 15-3 461 15-15 485 19-3 509 19-15 533 23-3 557 23-15
438 16-3 462 16-15 486 20-3 510 20-15 534 24-3 558 24-15
439 15-4 463 15-16 487 19-4 511 19-16 535 23-4 559 23-16
440 16-4 464 16-16 488 20-4 512 20-16 536 24-4 560 24-16
441 15-5 465 15-17 489 19-5 513 19-17 537 23-5 561 23-17
442 16-5 466 16-17 490 20-5 514 20-17 538 24-5 562 24-17
443 15-6 467 15-18 491 19-6 515 19-18 539 23-6 563 23-18
444 16-6 468 16-18 492 20-6 516 20-18 540 24-6 564 24-18
445 15-7 469 15-19 493 19-7 517 19-19 541 23-7 565 23-19
446 16-7 470 16-19 494 20-7 518 20-19 542 24-7 566 24-19
447 15-8 471 15-20 495 19-8 519 19-20 543 23-8 567 23-20
448 16-8 472 16-20 496 20-8 520 20-20 544 24-8 568 24-20
449 15-9 473 15-21 497 19-9 521 19-21 545 23-9 569 23-21
450 16-9 474 16-21 498 20-9 522 20-21 546 24-9 570 24-21
451 15-10 475 15-22 499 19-10 523 19-22 547 23-10 571 23-22
452 16-10 476 16-22 500 20-10 524 20-22 548 24-10 572 24-22
453 15-11 477 15-23 501 19-11 525 19-23 549 23-11 573 23-23
454 16-11 478 16-23 502 20-11 526 20-23 550 24-11 574 24-23
455 15-12 479 15-24 503 19-12 527 19-24 551 23-12 575 23-24
Spare*1 Spare*1 Spare*1
456 16-12 480 16-24 504 20-12 528 20-24 552 24-12 576 24-24
Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

INST03-11A-250
 No.
289 290 289 290 289 290 289 290 337 338 337 338 337 338 337 338

DKC
291 292 291 292 291 292 291 292 339 340 339 340 339 340 339 340
Rev.0 / Dec.2013

293 294 293 294 293 294 293 294 341 342 341 342 341 342 341 342

DKU-10
DKU-11
295 296 295 296 295 296 295 296 343 344 343 344 343 344 343 344

3.11.2-2.
Hitachi Proprietary

INST03-11A-260

297 298 297 298 297 298 297 298 345 346 345 346 345 346 345 346
299 300 299 300 299 300 299 300 347 348 347 348 347 348 347 348
301 302 301 302 301 302 301 302 349 350 349 350 349 350 349 350
303 304 303 304 303 304 303 304 351 352 351 352 351 352 351 352
added.

305 306 305 306 305 306 305 306 353 354 353 354 353 354 353 354
307 308 307 308 307 308 307 308 355 356 355 356 355 356 355 356
309 310 309 310 309 310 309 310 357 358 357 358 357 358 357 358
311 312 311 312 311 312 311 312 359 360 359 360 359 360 359 360
313 314 313 314 313 314 313 314 361 362 361 362 361 362 361 362
315 316 315 316 315 316 315 316 363 364 363 364 363 364 363 364

Front View
317 318 317 318 317 318 317 318 365 366 365 366 365 366 365 366
319 320 319 320 319 320 319 320 367 368 367 368 367 368 367 368
321 322 321 322 321 322 321 322 369 370 369 370 369 370 369 370
-12
323 324 323 324 323 324 323 324 371 372 371 372 371 372 371 372
325 326 325 326 325 326 325 326 373 374 373 374 373 374 373 374
327 328 327 328 327 328 327 328 375 376 375 376 375 376 375 376
329 330 329 330 329 330 329 330 377 378 377 378 377 378 377 378
-11
2 DKC-F810I-400MCM/800MCM × 4

331 332 331 332 331 332 331 332 379 380 379 380 379 380 379 380
333 334 333 334 333 334 333 334 381 382 381 382 381 382 381 382
335*1 336*1 335*1 336*1 335*1 336*1 335*1 336*1 383*1 384*1 383*1 384*1 383*1 384*1 383*1 384*1
Model Number

-10 -00

001 002 001 002 001 002 001 002 049 050 049 050 049 050 049 050

DKC
003 004 003 004 003 004 003 004 051 052 051 052 051 052 051 052
005 006 005 006 005 006 005 006 053 054 053 054 053 054 053 054

DKU-00
DKU-01
1 DKC-F810I-300KCM/600JCM/900JCM/1R2JCM × 4

007 008 007 008 007 008 007 008 055 056 055 056 055 056 055 056
-01

009 010 009 010 009 010 009 010 057 058 057 058 057 058 057 058
011 012 011 012 011 012 011 012 059 060 059 060 059 060 059 060
013 014 013 014 013 014 013 014 061 062 061 062 061 062 061 062
015 016 015 016 015 016 015 016 063 064 063 064 063 064 063 064
-02

017 018 017 018 017 018 017 018 065 066 065 066 065 066 065 066
RACK RACK RACK RACK RACK RACK

019 020 019 020 019 020 019 020 067 068 067 068 067 068 067 068
021 022 021 022 021 022 021 022 069 070 069 070 069 070 069 070
023 024 023 024 023 024 023 024 071 072 071 072 071 072 071 072
025 026 025 026 025 026 025 026 073 074 073 074 073 074 073 074
027 028 027 028 027 028 027 028 075 076 075 076 075 076 075 076
029 030 029 030 029 030 029 030 077 078 077 078 077 078 077 078

Front View
031 032 031 032 031 032 031 032 079 080 079 080 079 080 079 080
033 034 033 034 033 034 033 034 081 082 081 082 081 082 081 082
035 036 035 036 035 036 035 036 083 084 083 084 083 084 083 084
037 038 037 038 037 038 037 038 085 086 085 086 085 086 085 086
039 040 039 040 039 040 039 040 087 088 087 088 087 088 087 088
041 042 041 042 041 042 041 042 089 090 089 090 089 090 089 090
043 044 043 044 043 044 043 044 091 092 091 092 091 092 091 092
045 046 045 046 045 046 045 046 093 094 093 094 093 094 093 094
047*1 048*1 047*1 048*1 047*1 048*1 047*1 048*1 095*1 096*1 095*1 096*1 095*1 096*1 095*1 096*1
Model Name

SFF SSD Drive

SFF Disk Drive

is to be
installed.
*1: A data or
spare disk
Remarks

Fig. 3.11.2-2 (3D+1P/2D+2D) Data Drive/Parity Drive Expansion Sequence (1/3)

The relationship between drives installation order and RAID group number is shown in the Table

INST03-11A-260
Copyright © 2013, Hitachi, Ltd.

(1) Make sure of the location where the RAID group is installed and that where the drive is to be
DKC810I
 385 386 385 386 385 386 385 386 433 434 433 434 433 434 433 434
387 388 387 388 387 388 387 388 435 436 435 436 435 436 435 436
Rev.0 / Dec.2013

389 390 389 390 389 390 389 390 437 438 437 438 437 438 437 438

DKU-12
DKU-13
391 392 391 392 391 392 391 392 439 440 439 440 439 440 439 440

3.11.2-2.
Hitachi Proprietary

INST03-11A-270

393 394 393 394 393 394 393 394 441 442 441 442 441 442 441 442
395 396 395 396 395 396 395 396 443 444 443 444 443 444 443 444
397 398 397 398 397 398 397 398 445 446 445 446 445 446 445 446
399 400 399 400 399 400 399 400 447 448 447 448 447 448 447 448
401 402 401 402 401 402 401 402 449 450 449 450 449 450 449 450
403 404 403 404 403 404 403 404 451 452 451 452 451 452 451 452
405 406 405 406 405 406 405 406 453 454 453 454 453 454 453 454
407 408 407 408 407 408 407 408 455 456 455 456 455 456 455 456
409 410 409 410 409 410 409 410 457 458 457 458 457 458 457 458
411 412 411 412 411 412 411 412 459 460 459 460 459 460 459 460

Front View
413 414 413 414 413 414 413 414 461 462 461 462 461 462 461 462
415 416 415 416 415 416 415 416 463 464 463 464 463 464 463 464
417 418 417 418 417 418 417 418 465 466 465 466 465 466 465 466
-12

419 420 419 420 419 420 419 420 467 468 467 468 467 468 467 468
421 422 421 422 421 422 421 422 469 470 469 470 469 470 469 470
423 424 423 424 423 424 423 424 471 472 471 472 471 472 471 472
425 426 425 426 425 426 425 426 473 474 473 474 473 474 473 474
-11

427 428 427 428 427 428 427 428 475 476 475 476 475 476 475 476
429 430 429 430 429 430 429 430 477 478 477 478 477 478 477 478
431*1 432*1 431*1 432*1 431*1 432*1 431*1 432*1 479*1 480*1 479*1 480*1 479*1 480*1 479*1 480*1
-10 -00

097 098 097 098 097 098 097 098 145 146 145 146 145 146 145 146
099 100 099 100 099 100 099 100 147 148 147 148 147 148 147 148
101 102 101 102 101 102 101 102 149 150 149 150 149 150 149 150

DKU-02
DKU-03

103 104 103 104 103 104 103 104 151 152 151 152 151 152 151 152
-01

105 106 105 106 105 106 105 106 153 154 153 154 153 154 153 154
107 108 107 108 107 108 107 108 155 156 155 156 155 156 155 156
109 110 109 110 109 110 109 110 157 158 157 158 157 158 157 158
111 112 111 112 111 112 111 112 159 160 159 160 159 160 159 160
-02

113 114 113 114 113 114 113 114 161 162 161 162 161 162 161 162
RACK RACK RACK RACK RACK RACK

115 116 115 116 115 116 115 116 163 164 163 164 163 164 163 164
117 118 117 118 117 118 117 118 165 166 165 166 165 166 165 166
119 120 119 120 119 120 119 120 167 168 167 168 167 168 167 168
121 122 121 122 121 122 121 122 169 170 169 170 169 170 169 170
123 124 123 124 123 124 123 124 171 172 171 172 171 172 171 172
125 126 125 126 125 126 125 126 173 174 173 174 173 174 173 174

Front View
127 128 127 128 127 128 127 128 175 176 175 176 175 176 175 176
129 130 129 130 129 130 129 130 177 178 177 178 177 178 177 178
131 132 131 132 131 132 131 132 179 180 179 180 179 180 179 180
133 134 133 134 133 134 133 134 181 182 181 182 181 182 181 182
135 136 135 136 135 136 135 136 183 184 183 184 183 184 183 184
137 138 137 138 137 138 137 138 185 186 185 186 185 186 185 186
139 140 139 140 139 140 139 140 187 188 187 188 187 188 187 188
141 142 141 142 141 142 141 142 189 190 189 190 189 190 189 190
143*1 144*1 143*1 144*1 143*1 144*1 143*1 144*1 191*1 192*1 191*1 192*1 191*1 192*1 191*1 192*1

is to be
installed.
*1: A data or
spare disk

Fig. 3.11.2-2 (3D+1P/2D+2D) Data Drive/Parity Drive Expansion Sequence (2/3)

The relationship between drives installation order and RAID group number is shown in the Table

INST03-11A-270
Copyright © 2013, Hitachi, Ltd.
DKC810I
 481 482 481 482 481 482 481 482 529 530 529 530 529 530 529 530
483 484 483 484 483 484 483 484 531 532 531 532 531 532 531 532
Rev.0 / Dec.2013

485 486 485 486 485 486 485 486 533 534 533 534 533 534 533 534

DKU-14
DKU-15
487 488 487 488 487 488 487 488 535 536 535 536 535 536 535 536

3.11.2-2.
Hitachi Proprietary

INST03-11A-280

489 490 489 490 489 490 489 490 537 538 537 538 537 538 537 538
491 492 491 492 491 492 491 492 539 540 539 540 539 540 539 540
493 494 493 494 493 494 493 494 541 542 541 542 541 542 541 542
495 496 495 496 495 496 495 496 543 544 543 544 543 544 543 544
497 498 497 498 497 498 497 498 545 546 545 546 545 546 545 546
499 500 499 500 499 500 499 500 547 548 547 548 547 548 547 548
501 502 501 502 501 502 501 502 549 550 549 550 549 550 549 550
503 504 503 504 503 504 503 504 551 552 551 552 551 552 551 552
505 506 505 506 505 506 505 506 553 554 553 554 553 554 553 554
507 508 507 508 507 508 507 508 555 556 555 556 555 556 555 556

Front View
509 510 509 510 509 510 509 510 557 558 557 558 557 558 557 558
511 512 511 512 511 512 511 512 559 560 559 560 559 560 559 560
513 514 513 514 513 514 513 514 561 562 561 562 561 562 561 562
-12

515 516 515 516 515 516 515 516 563 564 563 564 563 564 563 564
517 518 517 518 517 518 517 518 565 566 565 566 565 566 565 566
519 520 519 520 519 520 519 520 567 568 567 568 567 568 567 568
521 522 521 522 521 522 521 522 569 570 569 570 569 570 569 570
-11

523 524 523 524 523 524 523 524 571 572 571 572 571 572 571 572
525 526 525 526 525 526 525 526 573 574 573 574 573 574 573 574
527*1 528*1 527*1 528*1 527*1 528*1 527*1 528*1 575*1 576*1 575*1 576*1 575*1 576*1 575*1 576*1
-10 -00

193 194 193 194 193 194 193 194 241 242 241 242 241 242 241 242
195 196 195 196 195 196 195 196 243 244 243 244 243 244 243 244
197 198 197 198 197 198 197 198 245 246 245 246 245 246 245 246

DKU-04
DKU-05

199 200 199 200 199 200 199 200 247 248 247 248 247 248 247 248
-01

201 202 201 202 201 202 201 202 249 250 249 250 249 250 249 250
203 204 203 204 203 204 203 204 251 252 251 252 251 252 251 252
205 206 205 206 205 206 205 206 253 254 253 254 253 254 253 254
207 208 207 208 207 208 207 208 255 256 255 256 255 256 255 256
-02

209 210 209 210 209 210 209 210 257 258 257 258 257 258 257 258
RACK RACK RACK RACK RACK RACK

211 212 211 212 211 212 211 212 259 260 259 260 259 260 259 260
213 214 213 214 213 214 213 214 261 262 261 262 261 262 261 262
215 216 215 216 215 216 215 216 263 264 263 264 263 264 263 264
217 218 217 218 217 218 217 218 265 266 265 266 265 266 265 266
219 220 219 220 219 220 219 220 267 268 267 268 267 268 267 268
221 222 221 222 221 222 221 222 269 270 269 270 269 270 269 270

Front View
223 224 223 224 223 224 223 224 271 272 271 272 271 272 271 272
225 226 225 226 225 226 225 226 273 274 273 274 273 274 273 274
227 228 227 228 227 228 227 228 275 276 275 276 275 276 275 276
229 230 229 230 229 230 229 230 277 278 277 278 277 278 277 278
231 232 231 232 231 232 231 232 279 280 279 280 279 280 279 280
233 234 233 234 233 234 233 234 281 282 281 282 281 282 281 282
235 236 235 236 235 236 235 236 283 284 283 284 283 284 283 284
237 238 237 238 237 238 237 238 285 286 285 286 285 286 285 286
239*1 240*1 239*1 240*1 239*1 240*1 239*1 240*1 287*1 288*1 287*1 288*1 287*1 288*1 287*1 288*1

is to be
installed.
*1: A data or
spare disk

Fig. 3.11.2-2 (3D+1P/2D+2D) Data Drive/Parity Drive Expansion Sequence (3/3)

The relationship between drives installation order and RAID group number is shown in the Table

INST03-11A-280
Copyright © 2013, Hitachi, Ltd.
DKC810I
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-290

(iii) RAID5 (3D+1P) / RAID1 (2D+2D), FBX (DKU for FMD)

Relations between the installation locations of the RAID groups and the RAID group
numbers set through the SVP are shown in Table 3.11.2-3.

Table 3.11.2-3 Relation between drives installation order and RAID group number
(3D+1P/2D+2D, FBX) (1/2)
DKU-00 DKU-01 DKU-02 DKU-03 DKU-04 DKU-05
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
001 1-1 013 5-1 025 9-1 037 13-1 049 17-1 061 21-1
002 1-2 014 5-2 026 9-2 038 13-2 050 17-2 062 21-2
003 1-3 015 5-3 027 9-3 039 13-3 051 17-3 063 21-3
004 1-4 016 5-4 028 9-4 040 13-4 052 17-4 064 21-4
005 1-5 017 5-5 029 9-5 041 13-5 053 17-5 065 21-5
006 1-6 018 5-6 030 9-6 042 13-6 054 17-6 066 21-6
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1
007 2-1 019 6-1 031 10-1 043 14-1 055 18-1 067 22-1
008 2-2 020 6-2 032 10-2 044 14-2 056 18-2 068 22-2
009 2-3 021 6-3 033 10-3 045 14-3 057 18-3 069 22-3
010 2-4 022 6-4 034 10-4 046 14-4 058 18-4 070 22-4
011 2-5 023 6-5 035 10-5 047 14-5 059 18-5 071 22-5
012 2-6 024 6-6 036 10-6 048 14-6 060 18-6 072 22-6
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

Table 3.11.2-3 Relation between drives installation order and RAID group number
(3D+1P/2D+2D, FBX) (2/2)
DKU-10 DKU-11 DKU-12 DKU-13 DKU-14 DKU-15
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
073 3-1 085 7-1 097 11-1 109 15-1 121 19-1 133 23-1
074 3-2 086 7-2 098 11-2 110 15-2 122 19-2 134 23-2
075 3-3 087 7-3 099 11-3 111 15-3 123 19-3 135 23-3
076 3-4 088 7-4 100 11-4 112 15-4 124 19-4 136 23-4
077 3-5 089 7-5 101 11-5 113 15-5 125 19-5 137 23-5
078 3-6 090 7-6 102 11-6 114 15-6 126 19-6 138 23-6
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1
079 4-1 091 8-1 103 12-1 115 16-1 127 20-1 139 24-1
080 4-2 092 8-2 104 12-2 116 16-2 128 20-2 140 24-2
081 4-3 093 8-3 105 12-3 117 16-3 129 20-3 141 24-3
082 4-4 094 8-4 106 12-4 118 16-4 130 20-4 142 24-4
083 4-5 095 8-5 107 12-5 119 16-5 131 20-5 143 24-5
084 4-6 096 8-6 108 12-6 120 16-6 132 20-6 144 24-6
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

INST03-11A-290
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-300

(1) Make sure of the location where the RAID group is installed and that where the drive is to be
added.
No. Model Number Model Name Remarks
1 DKC-F810I-1R6FM/3R2FM × 4 Flash Module Drive FMD

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-01
022 023 024*1
019 020 021
016 017 018*1
013 014 015
022 023 024*1
019 020 021
016 017 018*1 DKU-03 DKU-05
013 014 015 070 071 072*1
046 047 048*1
022 023 024*1 043 044 045 067 068 069
019 020 021 040 041 042*1 064 065 066*1
016 017 018*1 037 038 039 061 062 063
013 014 015 046 047 048*1 070 071 072*1
022 023 024*1 043 044 045 067 068 069
019 020 021 040 041 042*1 064 065 066*1
016 017 018*1 037 038 039 061 062 063
013 014 015 046 047 048*1 070 071 072*1
DKU-00 043 044 045 067 068 069
040 041 042*1 064 065 066*1
010 011 012*1 037 038 039 061 062 063
007 008 009 046 047 048*1 070 071 072*1
004 005 006*1 043 044 045 067 068 069
001 002 003 040 041 042*1 064 065 066*1
037 038 039 061 062 063
010 011 012*1
007 008 009 DKU-02 DKU-04
004 005 006*1
001 002 003 034 035 036*1 058 059 060*1
031 032 033 055 056 057
010 011 012*1 028 029 030*1 052 053 054*1
007 008 009 025 026 027 049 050 051
004 005 006*1 034 035 036*1 058 059 060*1
001 002 003 031 032 033 055 056 057
010 011 012*1 028 029 030*1 052 053 054*1
007 008 009 025 026 027 049 050 051
004 005 006*1 034 035 036*1 058 059 060*1
001 002 003 031 032 033 055 056 057
028 029 030*1 052 053 054*1
DKC-0 025 026 027 049 050 051 *1: A data or
034 035 036*1 058 059 060*1
031 032 033 055 056 057 spare disk
028 029 030*1 052 053 054*1 is to be
025 026 027 049 050 051
installed.

Front View

Fig. 3.11.2-3 (3D+1P/2D+2D) Data Drive/Parity Drive Expansion Sequence (1/2)

The relationship between drives installation order and RAID group number is shown in the Table
3.11.2-3.
INST03-11A-300
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-310

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-11
094 095 096*1
091 092 093
088 089 090*1
085 086 087
094 095 096*1
091 092 093
DKU-15 DKU-13 088 089 090*1
142 143 144*1 118 119 120*1 085 086 087
139 140 141 115 116 117 094 095 096*1
136 137 138*1 112 113 114*1 091 092 093
133 134 135 109 110 111 088 089 090*1
142 143 144*1 118 119 120*1 085 086 087
139 140 141 115 116 117 094 095 096*1
136 137 138*1 112 113 114*1 091 092 093
133 134 135 109 110 111 088 089 090*1
142 143 144*1 118 119 120*1 085 086 087
139 140 141 115 116 117
136 137 138*1 112 113 114*1 DKU-10
133 134 135 109 110 111 082 083 084*1
142 143 144*1 118 119 120*1 079 080 081
139 140 141 115 116 117 076 077 078*1
136 137 138*1 112 113 114*1 073 074 075
133 134 135 109 110 111
082 083 084*1
DKU-14 DKU-12 079 080 081
076 077 078*1
130 131 132*1 106 107 108*1 073 074 075
127 128 129 103 104 105
124 125 126*1 100 101 102*1 082 083 084*1
121 122 123 097 098 099 079 080 081
130 131 132*1 106 107 108*1 076 077 078*1
127 128 129 103 104 105 073 074 075
124 125 126*1 100 101 102*1 082 083 084*1
121 122 123 097 098 099 079 080 081
130 131 132*1 106 107 108*1 076 077 078*1
127 128 129 103 104 105 073 074 075
124 125 126*1 100 101 102*1
121 122 123 097 098 099 DKC-1 *1: A data or
130 131 132*1 106 107 108*1 spare disk
127 128 129 103 104 105
124 125 126*1 100 101 102*1 is to be
121 122 123 097 098 099 installed.

Front View

Fig. 3.11.2-3 (3D+1P/2D+2D) Data Drive/Parity Drive Expansion Sequence (2/2)

The relationship between drives installation order and RAID group number is shown in the Table
3.11.2-3.

INST03-11A-310
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-320

(iv) RAID5 (7D+1P) / RAID6 (6D+2P), UBX (DKU for 3.5 inch Drive)
Relations between the installation locations of the RAID groups and the RAID group
numbers set through the SVP are shown in Table 3.11.2-4.

Table 3.11.2-4 Relation between drives installation order and RAID group number
(7D+1P/6D+2P, UBX) (1/2)
DKU-00 DKU-01 DKU-02 DKU-03 DKU-04 DKU-05
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
001 1-1 013 5-1 025 9-1 037 13-1 049 17-1 061 21-1
002 1-2 014 5-2 026 9-2 038 13-2 050 17-2 062 21-2
003 1-3 015 5-3 027 9-3 039 13-3 051 17-3 063 21-3
004 1-4 016 5-4 028 9-4 040 13-4 052 17-4 064 21-4
005 1-5 017 5-5 029 9-5 041 13-5 053 17-5 065 21-5
006 1-6 018 5-6 030 9-6 042 13-6 054 17-6 066 21-6
007 1-7 019 5-7 031 9-7 043 13-7 055 17-7 067 21-7
008 1-8 020 5-8 032 9-8 044 13-8 056 17-8 068 21-8
009 1-9 021 5-9 033 9-9 045 13-9 057 17-9 069 21-9
010 1-10 022 5-10 034 9-10 046 13-10 058 17-10 070 21-10
011 1-11 023 5-11 035 9-11 047 13-11 059 17-11 071 21-11
012 1-12 024 5-12 036 9-12 048 13-12 060 17-12 072 21-12
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

Table 3.11.2-4 Relation between drives installation order and RAID group number
(7D+1P/6D+2P, UBX) (2/2)
DKU-10 DKU-11 DKU-12 DKU-13 DKU-14 DKU-15
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
073 3-1 085 7-1 097 11-1 109 15-1 121 19-1 133 23-1
074 3-2 086 7-2 098 11-2 110 15-2 122 19-2 134 23-2
075 3-3 087 7-3 099 11-3 111 15-3 123 19-3 135 23-3
076 3-4 088 7-4 100 11-4 112 15-4 124 19-4 136 23-4
077 3-5 089 7-5 101 11-5 113 15-5 125 19-5 137 23-5
078 3-6 090 7-6 102 11-6 114 15-6 126 19-6 138 23-6
079 3-7 091 7-7 103 11-7 115 15-7 127 19-7 139 23-7
080 3-8 092 7-8 104 11-8 116 15-8 128 19-8 140 23-8
081 3-9 093 7-9 105 11-9 117 15-9 129 19-9 141 23-9
082 3-10 094 7-10 106 11-10 118 15-10 130 19-10 142 23-10
083 3-11 095 7-11 107 11-11 119 15-11 131 19-11 143 23-11
084 3-12 096 7-12 108 11-12 120 15-12 132 19-12 144 23-12
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

INST03-11A-320
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-330

(1) Make sure of the location where the RAID group is installed and that where the drive is to be
added.
No. Model Number Model Name Remarks
1 DKC-F810I-3R0H3M/4R0H3M × 8 LFF Disk Drive

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-11 DKU-01
093 094 095 096*1 021 022 023 024*1
089 090 091 092 017 018 019 020
085 086 087 088 013 014 015 016
093 094 095 096*1 021 022 023 024*1
089 090 091 092 017 018 019 020
085 086 087 088 013 014 015 016
093 094 095 096*1 021 022 023 024*1
089 090 091 092 017 018 019 020
085 086 087 088 013 014 015 016
093 094 095 096*1 021 022 023 024*1
089 090 091 092 017 018 019 020
085 086 087 088 013 014 015 016
093 094 095 096*1 021 022 023 024*1
089 090 091 092 017 018 019 020
085 086 087 088 013 014 015 016
093 094 095 096*1 021 022 023 024*1
089 090 091 092 017 018 019 020
085 086 087 088 013 014 015 016
093 094 095 096*1 021 022 023 024*1
089 090 091 092 017 018 019 020
085 086 087 088 013 014 015 016
093 094 095 096*1 021 022 023 024*1
089 090 091 092 017 018 019 020
085 086 087 088 013 014 015 016
DKU-10 DKU-00
081 082 083 084*1 009 010 011 012*1
077 078 079 080 005 006 007 008
073 074 075 076 001 002 003 004
081 082 083 084*1 009 010 011 012*1
077 078 079 080 005 006 007 008
073 074 075 076 001 002 003 004
081 082 083 084*1 009 010 011 012*1
077 078 079 080 005 006 007 008
073 074 075 076 001 002 003 004
081 082 083 084*1 009 010 011 012*1
077 078 079 080 005 006 007 008
073 074 075 076 001 002 003 004
081 082 083 084*1 009 010 011 012*1
077 078 079 080 005 006 007 008
073 074 075 076 001 002 003 004
081 082 083 084*1 009 010 011 012*1
077 078 079 080 005 006 007 008
073 074 075 076 001 002 003 004
081 082 083 084*1 009 010 011 012*1
077 078 079 080 005 006 007 008
073 074 075 076 001 002 003 004
081 082 083 084*1 009 010 011 012*1
077 078 079 080 005 006 007 008
073 074 075 076 001 002 003 004
*1: A data or
DKC-1 DKC-0 spare disk
is to be
installed.

Front View Front View

Fig. 3.11.2-4 (7D+1P/6D+2P) Data Drive/Parity Drive Expansion Sequence (1/3)

The relationship between drives installation order and RAID group number is shown in the Table
3.11.2-4.
INST03-11A-330
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-340

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-13 DKU-03
117 118 119 120*1 045 046 047 048*1
113 114 115 116 041 042 043 044
109 110 111 112 037 038 039 040
117 118 119 120*1 045 046 047 048*1
113 114 115 116 041 042 043 044
109 110 111 112 037 038 039 040
117 118 119 120*1 045 046 047 048*1
113 114 115 116 041 042 043 044
109 110 111 112 037 038 039 040
117 118 119 120*1 045 046 047 048*1
113 114 115 116 041 042 043 044
109 110 111 112 037 038 039 040
117 118 119 120*1 045 046 047 048*1
113 114 115 116 041 042 043 044
109 110 111 112 037 038 039 040
117 118 119 120*1 045 046 047 048*1
113 114 115 116 041 042 043 044
109 110 111 112 037 038 039 040
117 118 119 120*1 045 046 047 048*1
113 114 115 116 041 042 043 044
109 110 111 112 037 038 039 040
117 118 119 120*1 045 046 047 048*1
113 114 115 116 041 042 043 044
109 110 111 112 037 038 039 040
DKU-12 DKU-02
105 106 107 108*1 033 034 035 036*1
101 102 103 104 029 030 031 032
097 098 099 100 025 026 027 028
105 106 107 108*1 033 034 035 036*1
101 102 103 104 029 030 031 032
097 098 099 100 025 026 027 028
105 106 107 108*1 033 034 035 036*1
101 102 103 104 029 030 031 032
097 098 099 100 025 026 027 028
105 106 107 108*1 033 034 035 036*1
101 102 103 104 029 030 031 032
097 098 099 100 025 026 027 028
105 106 107 108*1 033 034 035 036*1
101 102 103 104 029 030 031 032
097 098 099 100 025 026 027 028
105 106 107 108*1 033 034 035 036*1
101 102 103 104 029 030 031 032
097 098 099 100 025 026 027 028
105 106 107 108*1 033 034 035 036*1
*1: A data or
101 102 103 104 029 030 031 032 spare disk
097 098 099 100 025 026 027 028
is to be
105 106 107 108*1 033 034 035 036*1
101 102 103 104 029 030 031 032 installed.
097 098 099 100 025 026 027 028

Front View Front View

Fig. 3.11.2-4 (7D+1P/6D+2P) Data Drive/Parity Drive Expansion Sequence (2/3)

The relationship between drives installation order and RAID group number is shown in the Table
3.11.2-4.

INST03-11A-340
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-350

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-15 DKU-05
141 142 143 144*1 069 070 071 072*1
137 138 139 140 065 066 067 068
133 134 135 136 061 062 063 064
141 142 143 144*1 069 070 071 072*1
137 138 139 140 065 066 067 068
133 134 135 136 061 062 063 064
141 142 143 144*1 069 070 071 072*1
137 138 139 140 065 066 067 068
133 134 135 136 061 062 063 064
141 142 143 144*1 069 070 071 072*1
137 138 139 140 065 066 067 068
133 134 135 136 061 062 063 064
141 142 143 144*1 069 070 071 072*1
137 138 139 140 065 066 067 068
133 134 135 136 061 062 063 064
141 142 143 144*1 069 070 071 072*1
137 138 139 140 065 066 067 068
133 134 135 136 061 062 063 064
141 142 143 144*1 069 070 071 072*1
137 138 139 140 065 066 067 068
133 134 135 136 061 062 063 064
141 142 143 144*1 069 070 071 072*1
137 138 139 140 065 066 067 068
133 134 135 136 061 062 063 064
DKU-14 DKU-04
129 130 131 132*1 057 058 059 060*1
125 126 127 128 053 054 055 056
121 122 123 124 049 050 051 052
129 130 131 132*1 057 058 059 060*1
125 126 127 128 053 054 055 056
121 122 123 124 049 050 051 052
129 130 131 132*1 057 058 059 060*1
125 126 127 128 053 054 055 056
121 122 123 124 049 050 051 052
129 130 131 132*1 057 058 059 060*1
125 126 127 128 053 054 055 056
121 122 123 124 049 050 051 052
129 130 131 132*1 057 058 059 060*1
125 126 127 128 053 054 055 056
121 122 123 124 049 050 051 052
129 130 131 132*1 057 058 059 060*1
125 126 127 128 053 054 055 056
121 122 123 124 049 050 051 052
129 130 131 132*1 057 058 059 060*1
*1: A data or
125 126 127 128 053 054 055 056 spare disk
121 122 123 124 049 050 051 052
is to be
129 130 131 132*1 057 058 059 060*1
125 126 127 128 053 054 055 056 installed.
121 122 123 124 049 050 051 052

Front View Front View

Fig. 3.11.2-4 (7D+1P/6D+2P) Data Drive/Parity Drive Expansion Sequence (3/3)

The relationship between drives installation order and RAID group number is shown in the Table
3.11.2-4.

INST03-11A-350
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-360

(v) RAID5 (7D+1P) / RAID6 (6D+2P), SBX (DKU for 2.5 inch Drive)
Relations between the installation locations of the RAID groups and the RAID group
numbers set through the SVP are shown in Table 3.11.2-5.

Table 3.11.2-5 Relation between drives installation order and RAID group number
(7D+1P/6D+2P, SBX) (1/2)
DKU-00 DKU-01 DKU-02 DKU-03 DKU-04 DKU-05
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
001 1-1 025 5-1 049 9-1 073 13-1 097 17-1 121 21-1
002 1-2 026 5-2 050 9-2 074 13-2 098 17-2 122 21-2
003 1-3 027 5-3 051 9-3 075 13-3 099 17-3 123 21-3
004 1-4 028 5-4 052 9-4 076 13-4 100 17-4 124 21-4
005 1-5 029 5-5 053 9-5 077 13-5 101 17-5 125 21-5
006 1-6 030 5-6 054 9-6 078 13-6 102 17-6 126 21-6
007 1-7 031 5-7 055 9-7 079 13-7 103 17-7 127 21-7
008 1-8 032 5-8 056 9-8 080 13-8 104 17-8 128 21-8
009 1-9 033 5-9 057 9-9 081 13-9 105 17-9 129 21-9
010 1-10 034 5-10 058 9-10 082 13-10 106 17-10 130 21-10
011 1-11 035 5-11 059 9-11 083 13-11 107 17-11 131 21-11
012 1-12 036 5-12 060 9-12 084 13-12 108 17-12 132 21-12
013 1-13 037 5-13 061 9-13 085 13-13 109 17-13 133 21-13
014 1-14 038 5-14 062 9-14 086 13-14 110 17-14 134 21-14
015 1-15 039 5-15 063 9-15 087 13-15 111 17-15 135 21-15
016 1-16 040 5-16 064 9-16 088 13-16 112 17-16 136 21-16
017 1-17 041 5-17 065 9-17 089 13-17 113 17-17 137 21-17
018 1-18 042 5-18 066 9-18 090 13-18 114 17-18 138 21-18
019 1-19 043 5-19 067 9-19 091 13-19 115 17-19 139 21-19
020 1-20 044 5-20 068 9-20 092 13-20 116 17-20 140 21-20
021 1-21 045 5-21 069 9-21 093 13-21 117 17-21 141 21-21
022 1-22 046 5-22 070 9-22 094 13-22 118 17-22 142 21-22
023 1-23 047 5-23 071 9-23 095 13-23 119 17-23 143 21-23
024 1-24 048 5-24 072 9-24 096 13-24 120 17-24 144 21-24
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

INST03-11A-360
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-370

Table 3.11.2-5 Relation between drives installation order and RAID group number
(7D+1P/6D+2P, SBX) (2/2)
DKU-10 DKU-11 DKU-12 DKU-13 DKU-14 DKU-15
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
145 3-1 169 7-1 193 11-1 217 15-1 241 19-1 265 23-1
146 3-2 170 7-2 194 11-2 218 15-2 242 19-2 266 23-2
147 3-3 171 7-3 195 11-3 219 15-3 243 19-3 267 23-3
148 3-4 172 7-4 196 11-4 220 15-4 244 19-4 268 23-4
149 3-5 173 7-5 197 11-5 221 15-5 245 19-5 269 23-5
150 3-6 174 7-6 198 11-6 222 15-6 246 19-6 270 23-6
151 3-7 175 7-7 199 11-7 223 15-7 247 19-7 271 23-7
152 3-8 176 7-8 200 11-8 224 15-8 248 19-8 272 23-8
153 3-9 177 7-9 201 11-9 225 15-9 249 19-9 273 23-9
154 3-10 178 7-10 202 11-10 226 15-10 250 19-10 274 23-10
155 3-11 179 7-11 203 11-11 227 15-11 251 19-11 275 23-11
156 3-12 180 7-12 204 11-12 228 15-12 252 19-12 276 23-12
157 3-13 181 7-13 205 11-13 229 15-13 253 19-13 277 23-13
158 3-14 182 7-14 206 11-14 230 15-14 254 19-14 278 23-14
159 3-15 183 7-15 207 11-15 231 15-15 255 19-15 279 23-15
160 3-16 184 7-16 208 11-16 232 15-16 256 19-16 280 23-16
161 3-17 185 7-17 209 11-17 233 15-17 257 19-17 281 23-17
162 3-18 186 7-18 210 11-18 234 15-18 258 19-18 282 23-18
163 3-19 187 7-19 211 11-19 235 15-19 259 19-19 283 23-19
164 3-20 188 7-20 212 11-20 236 15-20 260 19-20 284 23-20
165 3-21 189 7-21 213 11-21 237 15-21 261 19-21 285 23-21
166 3-22 190 7-22 214 11-22 238 15-22 262 19-22 286 23-22
167 3-23 191 7-23 215 11-23 239 15-23 263 19-23 287 23-23
168 3-24 192 7-24 216 11-24 240 15-24 264 19-24 288 23-24
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

INST03-11A-370
 No.
145 145 145 145 145 145 145 145 169 169 169 169 169 169 169 169

DKC
146 146 146 146 146 146 146 146 170 170 170 170 170 170 170 170
Rev.0 / Dec.2013

147 147 147 147 147 147 147 147 171 171 171 171 171 171 171 171

DKU-10
DKU-11
148 148 148 148 148 148 148 148 172 172 172 172 172 172 172 172

3.11.2-5.
Hitachi Proprietary

INST03-11A-380

149 149 149 149 149 149 149 149 173 173 173 173 173 173 173 173
150 150 150 150 150 150 150 150 174 174 174 174 174 174 174 174
151 151 151 151 151 151 151 151 175 175 175 175 175 175 175 175
152 152 152 152 152 152 152 152 176 176 176 176 176 176 176 176
added.

153 153 153 153 153 153 153 153 177 177 177 177 177 177 177 177
154 154 154 154 154 154 154 154 178 178 178 178 178 178 178 178
155 155 155 155 155 155 155 155 179 179 179 179 179 179 179 179
156 156 156 156 156 156 156 156 180 180 180 180 180 180 180 180
157 157 157 157 157 157 157 157 181 181 181 181 181 181 181 181
158 158 158 158 158 158 158 158 182 182 182 182 182 182 182 182

Front View
159 159 159 159 159 159 159 159 183 183 183 183 183 183 183 183
160 160 160 160 160 160 160 160 184 184 184 184 184 184 184 184
161 161 161 161 161 161 161 161 185 185 185 185 185 185 185 185
-12
162 162 162 162 162 162 162 162 186 186 186 186 186 186 186 186
163 163 163 163 163 163 163 163 187 187 187 187 187 187 187 187
164 164 164 164 164 164 164 164 188 188 188 188 188 188 188 188
165 165 165 165 165 165 165 165 189 189 189 189 189 189 189 189
-11
2 DKC-F810I-400MCM/800MCM × 8

166 166 166 166 166 166 166 166 190 190 190 190 190 190 190 190
167 167 167 167 167 167 167 167 191 191 191 191 191 191 191 191
168*1 168*1 168*1 168*1 168*1 168*1 168*1 168*1 192*1 192*1 192*1 192*1 192*1 192*1 192*1 192*1
Model Number

-10 -00

001 001 001 001 001 001 001 001 025 025 025 025 025 025 025 025

DKC
002 002 002 002 002 002 002 002 026 026 026 026 026 026 026 026
003 003 003 003 003 003 003 003 027 027 027 027 027 027 027 027

DKU-00
DKU-01
1 DKC-F810I-300KCM/600JCM/900JCM/1R2JCM × 8

004 004 004 004 004 004 004 004 028 028 028 028 028 028 028 028
-01

005 005 005 005 005 005 005 005 029 029 029 029 029 029 029 029
006 006 006 006 006 006 006 006 030 030 030 030 030 030 030 030
007 007 007 007 007 007 007 007 031 031 031 031 031 031 031 031
008 008 008 008 008 008 008 008 032 032 032 032 032 032 032 032
-02

009 009 009 009 009 009 009 009 033 033 033 033 033 033 033 033
RACK RACK RACK RACK RACK RACK

010 010 010 010 010 010 010 010 034 034 034 034 034 034 034 034
011 011 011 011 011 011 011 011 035 035 035 035 035 035 035 035
012 012 012 012 012 012 012 012 036 036 036 036 036 036 036 036
013 013 013 013 013 013 013 013 037 037 037 037 037 037 037 037
014 014 014 014 014 014 014 014 038 038 038 038 038 038 038 038
015 015 015 015 015 015 015 015 039 039 039 039 039 039 039 039

Front View
016 016 016 016 016 016 016 016 040 040 040 040 040 040 040 040
017 017 017 017 017 017 017 017 041 041 041 041 041 041 041 041
018 018 018 018 018 018 018 018 042 042 042 042 042 042 042 042
019 019 019 019 019 019 019 019 043 043 043 043 043 043 043 043
020 020 020 020 020 020 020 020 044 044 044 044 044 044 044 044
021 021 021 021 021 021 021 021 045 045 045 045 045 045 045 045
022 022 022 022 022 022 022 022 046 046 046 046 046 046 046 046
023 023 023 023 023 023 023 023 047 047 047 047 047 047 047 047
024*1 024*1 024*1 024*1 024*1 024*1 024*1 024*1 048*1 048*1 048*1 048*1 048*1 048*1 048*1 048*1
Model Name

SFF SSD Drive

SFF Disk Drive

is to be
installed.
*1: A data or
spare disk
Remarks

Fig. 3.11.2-5 (7D+1P/6D+2P) Data Drive/Parity Drive Expansion Sequence (1/3)

The relationship between drives installation order and RAID group number is shown in the Table

INST03-11A-380
Copyright © 2013, Hitachi, Ltd.

(1) Make sure of the location where the RAID group is installed and that where the drive is to be
DKC810I
 193 193 193 193 193 193 193 193 217 217 217 217 217 217 217 217
194 194 194 194 194 194 194 194 218 218 218 218 218 218 218 218
Rev.0 / Dec.2013

195 195 195 195 195 195 195 195 219 219 219 219 219 219 219 219

DKU-12
DKU-13
196 196 196 196 196 196 196 196 220 220 220 220 220 220 220 220

3.11.2-5.
Hitachi Proprietary

INST03-11A-390

197 197 197 197 197 197 197 197 221 221 221 221 221 221 221 221
198 198 198 198 198 198 198 198 222 222 222 222 222 222 222 222
199 199 199 199 199 199 199 199 223 223 223 223 223 223 223 223
200 200 200 200 200 200 200 200 224 224 224 224 224 224 224 224
201 201 201 201 201 201 201 201 225 225 225 225 225 225 225 225
202 202 202 202 202 202 202 202 226 226 226 226 226 226 226 226
203 203 203 203 203 203 203 203 227 227 227 227 227 227 227 227
204 204 204 204 204 204 204 204 228 228 228 228 228 228 228 228
205 205 205 205 205 205 205 205 229 229 229 229 229 229 229 229
206 206 206 206 206 206 206 206 230 230 230 230 230 230 230 230

Front View
207 207 207 207 207 207 207 207 231 231 231 231 231 231 231 231
208 208 208 208 208 208 208 208 232 232 232 232 232 232 232 232
209 209 209 209 209 209 209 209 233 233 233 233 233 233 233 233
-12

210 210 210 210 210 210 210 210 234 234 234 234 234 234 234 234
211 211 211 211 211 211 211 211 235 235 235 235 235 235 235 235
212 212 212 212 212 212 212 212 236 236 236 236 236 236 236 236
213 213 213 213 213 213 213 213 237 237 237 237 237 237 237 237
-11

214 214 214 214 214 214 214 214 238 238 238 238 238 238 238 238
215 215 215 215 215 215 215 215 239 239 239 239 239 239 239 239
216*1 216*1 216*1 216*1 216*1 216*1 216*1 216*1 240*1 240*1 240*1 240*1 240*1 240*1 240*1 240*1
-10 -00

049 049 049 049 049 049 049 049 073 073 073 073 073 073 073 073
050 050 050 050 050 050 050 050 074 074 074 074 074 074 074 074
051 051 051 051 051 051 051 051 075 075 075 075 075 075 075 075

DKU-02
DKU-03

052 052 052 052 052 052 052 052 076 076 076 076 076 076 076 076
-01

053 053 053 053 053 053 053 053 077 077 077 077 077 077 077 077
054 054 054 054 054 054 054 054 078 078 078 078 078 078 078 078
055 055 055 055 055 055 055 055 079 079 079 079 079 079 079 079
056 056 056 056 056 056 056 056 080 080 080 080 080 080 080 080
-02

057 057 057 057 057 057 057 057 081 081 081 081 081 081 081 081
RACK RACK RACK RACK RACK RACK

058 058 058 058 058 058 058 058 082 082 082 082 082 082 082 082
059 059 059 059 059 059 059 059 083 083 083 083 083 083 083 083
060 060 060 060 060 060 060 060 084 084 084 084 084 084 084 084
061 061 061 061 061 061 061 061 085 085 085 085 085 085 085 085
062 062 062 062 062 062 062 062 086 086 086 086 086 086 086 086
063 063 063 063 063 063 063 063 087 087 087 087 087 087 087 087

Front View
064 064 064 064 064 064 064 064 088 088 088 088 088 088 088 088
065 065 065 065 065 065 065 065 089 089 089 089 089 089 089 089
066 066 066 066 066 066 066 066 090 090 090 090 090 090 090 090
067 067 067 067 067 067 067 067 091 091 091 091 091 091 091 091
068 068 068 068 068 068 068 068 092 092 092 092 092 092 092 092
069 069 069 069 069 069 069 069 093 093 093 093 093 093 093 093
070 070 070 070 070 070 070 070 094 094 094 094 094 094 094 094
071 071 071 071 071 071 071 071 095 095 095 095 095 095 095 095
072*1 072*1 072*1 072*1 072*1 072*1 072*1 072*1 096*1 096*1 096*1 096*1 096*1 096*1 096*1 096*1

is to be
installed.
*1: A data or
spare disk

Fig. 3.11.2-5 (7D+1P/6D+2P) Data Drive/Parity Drive Expansion Sequence (2/3)

The relationship between drives installation order and RAID group number is shown in the Table

INST03-11A-390
Copyright © 2013, Hitachi, Ltd.
DKC810I
 241 241 241 241 241 241 241 241 265 265 265 265 265 265 265 265
242 242 242 242 242 242 242 242 266 266 266 266 266 266 266 266
Rev.0 / Dec.2013

243 243 243 243 243 243 243 243 267 267 267 267 267 267 267 267

DKU-14
DKU-15
244 244 244 244 244 244 244 244 268 268 268 268 268 268 268 268

3.11.2-5.
Hitachi Proprietary

INST03-11A-400

245 245 245 245 245 245 245 245 269 269 269 269 269 269 269 269
246 246 246 246 246 246 246 246 270 270 270 270 270 270 270 270
247 247 247 247 247 247 247 247 271 271 271 271 271 271 271 271
248 248 248 248 248 248 248 248 272 272 272 272 272 272 272 272
249 249 249 249 249 249 249 249 273 273 273 273 273 273 273 273
250 250 250 250 250 250 250 250 274 274 274 274 274 274 274 274
251 251 251 251 251 251 251 251 275 275 275 275 275 275 275 275
252 252 252 252 252 252 252 252 276 276 276 276 276 276 276 276
253 253 253 253 253 253 253 253 277 277 277 277 277 277 277 277
254 254 254 254 254 254 254 254 278 278 278 278 278 278 278 278

Front View
255 255 255 255 255 255 255 255 279 279 279 279 279 279 279 279
256 256 256 256 256 256 256 256 280 280 280 280 280 280 280 280
257 257 257 257 257 257 257 257 281 281 281 281 281 281 281 281
-12

258 258 258 258 258 258 258 258 282 282 282 282 282 282 282 282
259 259 259 259 259 259 259 259 283 283 283 283 283 283 283 283
260 260 260 260 260 260 260 260 284 284 284 284 284 284 284 284
261 261 261 261 261 261 261 261 285 285 285 285 285 285 285 285
-11

262 262 262 262 262 262 262 262 286 286 286 286 286 286 286 286
263 263 263 263 263 263 263 263 287 287 287 287 287 287 287 287
264*1 264*1 264*1 264*1 264*1 264*1 264*1 264*1 288*1 288*1 288*1 288*1 288*1 288*1 288*1 288*1
-10 -00

097 097 097 097 097 097 097 097 121 121 121 121 121 121 121 121
098 098 098 098 098 098 098 098 122 122 122 122 122 122 122 122
099 099 099 099 099 099 099 099 123 123 123 123 123 123 123 123

DKU-04
DKU-05

100 100 100 100 100 100 100 100 124 124 124 124 124 124 124 124
-01

101 101 101 101 101 101 101 101 125 125 125 125 125 125 125 125
102 102 102 102 102 102 102 102 126 126 126 126 126 126 126 126
103 103 103 103 103 103 103 103 127 127 127 127 127 127 127 127
104 104 104 104 104 104 104 104 128 128 128 128 128 128 128 128
-02

105 105 105 105 105 105 105 105 129 129 129 129 129 129 129 129
RACK RACK RACK RACK RACK RACK

106 106 106 106 106 106 106 106 130 130 130 130 130 130 130 130
107 107 107 107 107 107 107 107 131 131 131 131 131 131 131 131
108 108 108 108 108 108 108 108 132 132 132 132 132 132 132 132
109 109 109 109 109 109 109 109 133 133 133 133 133 133 133 133
110 110 110 110 110 110 110 110 134 134 134 134 134 134 134 134
111 111 111 111 111 111 111 111 135 135 135 135 135 135 135 135

Front View
112 112 112 112 112 112 112 112 136 136 136 136 136 136 136 136
113 113 113 113 113 113 113 113 137 137 137 137 137 137 137 137
114 114 114 114 114 114 114 114 138 138 138 138 138 138 138 138
115 115 115 115 115 115 115 115 139 139 139 139 139 139 139 139
116 116 116 116 116 116 116 116 140 140 140 140 140 140 140 140
117 117 117 117 117 117 117 117 141 141 141 141 141 141 141 141
118 118 118 118 118 118 118 118 142 142 142 142 142 142 142 142
119 119 119 119 119 119 119 119 143 143 143 143 143 143 143 143
120*1 120*1 120*1 120*1 120*1 120*1 120*1 120*1 144*1 144*1 144*1 144*1 144*1 144*1 144*1 144*1

is to be
installed.
*1: A data or
spare disk

Fig. 3.11.2-5 (7D+1P/6D+2P) Data Drive/Parity Drive Expansion Sequence (3/3)

The relationship between drives installation order and RAID group number is shown in the Table

INST03-11A-400
Copyright © 2013, Hitachi, Ltd.
DKC810I
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-410

(vi) RAID5 (7D+1P) / RAID6 (6D+2P), FBX (DKU for FMD)

Relations between the installation locations of the RAID groups and the RAID group
numbers set through the SVP are shown in Table 3.11.2-6.

Table 3.11.2-6 Relation between drives installation order and RAID group number
(7D+1P/6D+2P, FBX) (1/2)
DKU-00 DKU-01 DKU-02 DKU-03 DKU-04 DKU-05
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
001 1-1 007 5-1 013 9-1 019 13-1 025 17-1 031 21-1
002 1-2 008 5-2 014 9-2 020 13-2 026 17-2 032 21-2
003 1-3 009 5-3 015 9-3 021 13-3 027 17-3 033 21-3
004 1-4 010 5-4 016 9-4 022 13-4 028 17-4 034 21-4
005 1-5 011 5-5 017 9-5 023 13-5 029 17-5 035 21-5
006 1-6 012 5-6 018 9-6 024 13-6 030 17-6 036 21-6
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

Table 3.11.2-6 Relation between drives installation order and RAID group number
(7D+1P/6D+2P, FBX) (2/2)
DKU-10 DKU-11 DKU-12 DKU-13 DKU-14 DKU-15
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
037 3-1 043 7-1 049 11-1 055 15-1 061 19-1 067 23-1
038 3-2 044 7-2 050 11-2 056 15-2 062 19-2 068 23-2
039 3-3 045 7-3 051 11-3 057 15-3 063 19-3 069 23-3
040 3-4 046 7-4 052 11-4 058 15-4 064 19-4 070 23-4
041 3-5 047 7-5 053 11-5 059 15-5 065 19-5 071 23-5
042 3-6 048 7-6 054 11-6 060 15-6 066 19-6 072 23-6
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

INST03-11A-410
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-420

(1) Make sure of the location where the RAID group is installed and that where the drive is to be
added.
No. Model Number Model Name Remarks
1 DKC-F810I-1R6FM/3R2FM × 8 Flash Module Drive FMD

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-01
010 011 012*1
007 008 009
010 011 012*1
007 008 009
010 011 012*1
007 008 009
010 011 012*1 DKU-03 DKU-05
007 008 009 034 035 036*1
022 023 024*1
010 011 012*1 019 020 021 031 032 033
007 008 009 022 023 024*1 034 035 036*1
010 011 012*1 019 020 021 031 032 033
007 008 009 034 035 036*1
022 023 024*1
010 011 012*1 019 020 021 031 032 033
007 008 009 022 023 024*1 034 035 036*1
010 011 012*1 019 020 021 031 032 033
007 008 009 034 035 036*1
022 023 024*1
DKU-00 019 020 021 031 032 033
022 023 024*1 034 035 036*1
004 005 006*1 019 020 021 031 032 033
001 002 003 022 023 024*1 034 035 036*1
004 005 006*1 019 020 021 031 032 033
001 002 003 022 023 024*1 034 035 036*1
019 020 021 031 032 033
004 005 006*1
001 002 003 DKU-02 DKU-04
004 005 006*1
001 002 003 016 017 018*1 028 029 030*1
013 014 015 025 026 027
004 005 006*1 016 017 018*1 028 029 030*1
001 002 003 013 014 015 025 026 027
004 005 006*1 016 017 018*1 028 029 030*1
001 002 003 013 014 015 025 026 027
004 005 006*1 016 017 018*1 028 029 030*1
001 002 003 013 014 015 025 026 027
004 005 006*1 016 017 018*1 028 029 030*1
001 002 003 013 014 015 025 026 027
016 017 018*1 028 029 030*1 *1: A data or
DKC-0 013 014 015 025 026 027
016 017 018*1 028 029 030*1 spare disk
013 014 015 025 026 027 is to be
016 017 018*1 028 029 030*1
013 014 015 025 026 027 installed.

Front View

Fig. 3.11.2-6 (7D+1P/6D+2P) Data Drive/Parity Drive Expansion Sequence (1/2)

The relationship between drives installation order and RAID group number is shown in the Table
3.11.2-6.
INST03-11A-420
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-430

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-11
046 047 048*1
043 044 045
046 047 048*1
043 044 045
046 047 048*1
DKU-13 043 044 045
DKU-15 046 047 048*1
070 071 072*1 058 059 060*1 043 044 045
067 068 069 055 056 057 046 047 048*1
070 071 072*1 058 059 060*1 043 044 045
067 068 069 055 056 057 046 047 048*1
070 071 072*1 058 059 060*1 043 044 045
067 068 069 055 056 057 046 047 048*1
070 071 072*1 058 059 060*1 043 044 045
067 068 069 055 056 057 046 047 048*1
070 071 072*1 058 059 060*1 043 044 045
067 068 069 055 056 057
070 071 072*1 058 059 060*1 DKU-10
067 068 069 055 056 057 040 041 042*1
070 071 072*1 058 059 060*1 037 038 039
067 068 069 055 056 057 040 041 042*1
070 071 072*1 058 059 060*1 037 038 039
067 068 069 055 056 057
040 041 042*1
DKU-14 DKU-12 037 038 039
040 041 042*1
064 065 066*1 052 053 054*1 037 038 039
061 062 063 049 050 051
064 065 066*1 052 053 054*1 040 041 042*1
061 062 063 049 050 051 037 038 039
064 065 066*1 052 053 054*1 040 041 042*1
061 062 063 049 050 051 037 038 039
064 065 066*1 052 053 054*1 040 041 042*1
061 062 063 049 050 051 037 038 039
064 065 066*1 052 053 054*1 040 041 042*1
061 062 063 049 050 051 037 038 039 *1: A data or
064 065 066*1 052 053 054*1
061 062 063 049 050 051 DKC-1 spare disk
064 065 066*1 052 053 054*1
061 062 063 049 050 051 is to be
064 065 066*1 052 053 054*1 installed.
061 062 063 049 050 051

Front View

Fig. 3.11.2-6 (7D+1P/6D+2P) Data Drive/Parity Drive Expansion Sequence (2/2)

The relationship between drives installation order and RAID group number is shown in the Table
3.11.2-6.

INST03-11A-430
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-440

(vii) RAID6 (14D+2P), UBX (DKU for 3.5 inch Drive)

Relations between the installation locations of the RAID groups and the RAID group
numbers set through the SVP are shown in Table 3.11.2-7.

Table 3.11.2-7 Relation between drives installation order and RAID group number
(14D+2P, UBX) (1/2)
DKU-00 DKU-01 DKU-02 DKU-03 DKU-04 DKU-05
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
001 1-1 007 5-1 013 9-1 019 13-1 025 17-1 031 21-1
002 1-3 008 5-3 014 9-3 020 13-3 026 17-3 032 21-3
003 1-5 009 5-5 015 9-5 021 13-5 027 17-5 033 21-5
004 1-7 010 5-7 016 9-7 022 13-7 028 17-7 034 21-7
005 1-9 011 5-9 017 9-9 023 13-9 029 17-9 035 21-9
006 1-11 012 5-11 018 9-11 024 13-1 030 17-11 036 21-11
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

Table 3.11.2-7 Relation between drives installation order and RAID group number
(14D+2P, UBX) (2/2)
DKU-10 DKU-11 DKU-12 DKU-13 DKU-14 DKU-15
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
037 3-1 043 7-1 049 11-1 055 15-1 061 19-1 067 23-1
038 3-3 044 7-3 050 11-3 056 15-3 062 19-3 068 23-3
039 3-5 045 7-5 051 11-5 057 15-5 063 19-5 069 23-5
040 3-7 046 7-7 052 11-7 058 15-7 064 19-7 070 23-7
041 3-9 047 7-9 053 11-9 059 15-9 065 19-9 071 23-9
Spare*1
042 3-11 048 7-11 054 11-11 060 15-11 066 1-19 072 23-11
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

INST03-11A-440
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-450

(1) Make sure of the location where the RAID group is installed and that where the drive is to be
added.
No. Model Number Model Name Remarks
1 DKC-F810I-3R0H3M/4R0H3M × 16 LFF Disk Drive

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-11 DKU-01
047 047 048 048*1 011 011 012 012*1
045 045 046 046 009 009 010 010
043 043 044 044 007 007 008 008
047 047 048 048*1 011 011 012 012*1
045 045 046 046 009 009 010 010
043 043 044 044 007 007 008 008
047 047 048 048*1 011 011 012 012*1
045 045 046 046 009 009 010 010
043 043 044 044 007 007 008 008
047 047 048 048*1 011 011 012 012*1
045 045 046 046 009 009 010 010
043 043 044 044 007 007 008 008
047 047 048 048*1 011 011 012 012*1
045 045 046 046 009 009 010 010
043 043 044 044 007 007 008 008
047 047 048 048*1 011 011 012 012*1
045 045 046 046 009 009 010 010
043 043 044 044 007 007 008 008
047 047 048 048*1 011 011 012 012*1
045 045 046 046 009 009 010 010
043 043 044 044 007 007 008 008
047 047 048 048*1 011 011 012 012*1
045 045 046 046 009 009 010 010
043 043 044 044 007 007 008 008
DKU-10 DKU-00
041 041 042 042*1 005 005 006 006*1
039 039 040 040 003 003 004 004
037 037 038 038 001 001 002 002
041 041 042 042*1 005 005 006 006*1
039 039 040 040 003 003 004 004
037 037 038 038 001 001 002 002
041 041 042 042*1 005 005 006 006*1
039 039 040 040 003 003 004 004
037 037 038 038 001 001 002 002
041 041 042 042*1 005 005 006 006*1
039 039 040 040 003 003 004 004
037 037 038 038 001 001 002 002
041 041 042 042*1 005 005 006 006*1
039 039 040 040 003 003 004 004
037 037 038 038 001 001 002 002
041 041 042 042*1 005 005 006 006*1
039 039 040 040 003 003 004 004
037 037 038 038 001 001 002 002
041 041 042 042*1 005 005 006 006*1
039 039 040 040 003 003 004 004
037 037 038 038 001 001 002 002
041 041 042 042*1 005 005 006 006*1
039 039 040 040 003 003 004 004
037 037 038 038 001 001 002 002
*1: A data or
DKC-1 DKC-0 spare disk
is to be
installed.

Front View Front View

Fig. 3.11.2-7 (14D+2P) Data Drive/Parity Drive Expansion Sequence (1/3)

The relationship between drives installation order and RAID group number is shown in the Table
3.11.2-7.
INST03-11A-450
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-460

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-13 DKU-03
059 059 060 060*1 023 023 024 024*1
057 057 058 058 021 021 022 022
055 055 056 056 019 019 020 020
059 059 060 060*1 023 023 024 024*1
057 057 058 058 021 021 022 022
055 055 056 056 019 019 020 020
059 059 060 060*1 023 023 024 024*1
057 057 058 058 021 021 022 022
055 055 056 056 019 019 020 020
059 059 060 060*1 023 023 024 024*1
057 057 058 058 021 021 022 022
055 055 056 056 019 019 020 020
059 059 060 060*1 023 023 024 024*1
057 057 058 058 021 021 022 022
055 055 056 056 019 019 020 020
059 059 060 060*1 023 023 024 024*1
057 057 058 058 021 021 022 022
055 055 056 056 019 019 020 020
059 059 060 060*1 023 023 024 024*1
057 057 058 058 021 021 022 022
055 055 056 056 019 019 020 020
059 059 060 060*1 023 023 024 024*1
057 057 058 058 021 021 022 022
055 055 056 056 019 019 020 020
DKU-12 DKU-02
053 053 054 054*1 017 017 018 018*1
051 051 052 052 015 015 016 016
049 049 050 050 013 013 014 014
053 053 054 054*1 017 017 018 018*1
051 051 052 052 015 015 016 016
049 049 050 050 013 013 014 014
053 053 054 054*1 017 017 018 018*1
051 051 052 052 015 015 016 016
049 049 050 050 013 013 014 014
053 053 054 054*1 017 017 018 018*1
051 051 052 052 015 015 016 016
049 049 050 050 013 013 014 014
053 053 054 054*1 017 017 018 018*1
051 051 052 052 015 015 016 016
049 049 050 050 013 013 014 014
053 053 054 054*1 017 017 018 018*1
051 051 052 052 015 015 016 016
049 049 050 050 013 013 014 014
053 053 054 054*1 017 017 018 018*1
*1: A data or
051 051 052 052 015 015 016 016 spare disk
049 049 050 050 013 013 014 014
is to be
053 053 054 054*1 017 017 018 018*1
051 051 052 052 015 015 016 016 installed.
049 049 050 050 013 013 014 014

Front View Front View

Fig. 3.11.2-7 (14D+2P) Data Drive/Parity Drive Expansion Sequence (2/3)

The relationship between drives installation order and RAID group number is shown in the Table
3.11.2-7.

INST03-11A-460
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-470

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-15 DKU-05
071 071 072 072*1 035 035 036 036*1
069 069 070 070 033 033 034 034
067 067 068 068 031 031 032 032
071 071 072 072*1 035 035 036 036*1
069 069 070 070 033 033 034 034
067 067 068 068 031 031 032 032
071 071 072 072*1 035 035 036 036*1
069 069 070 070 033 033 034 034
067 067 068 068 031 031 032 032
071 071 072 072*1 035 035 036 036*1
069 069 070 070 033 033 034 034
067 067 068 068 031 031 032 032
071 071 072 072*1 035 035 036 036*1
069 069 070 070 033 033 034 034
067 067 068 068 031 031 032 032
071 071 072 072*1 035 035 036 036*1
069 069 070 070 033 033 034 034
067 067 068 068 031 031 032 032
071 071 072 072*1 035 035 036 036*1
069 069 070 070 033 033 034 034
067 067 068 068 031 031 032 032
071 071 072 072*1 035 035 036 036*1
069 069 070 070 033 033 034 034
067 067 068 068 031 031 032 032
DKU-14 DKU-04
065 065 066 066*1 029 029 030 030*1
063 063 064 064 027 027 028 028
061 061 062 062 025 025 026 026
065 065 066 066*1 029 029 030 030*1
063 063 064 064 027 027 028 028
061 061 062 062 025 025 026 026
065 065 066 066*1 029 029 030 030*1
063 063 064 064 027 027 028 028
061 061 062 062 025 025 026 026
065 065 066 066*1 029 029 030 030*1
063 063 064 064 027 027 028 028
061 061 062 062 025 025 026 026
065 065 066 066*1 029 029 030 030*1
063 063 064 064 027 027 028 028
061 061 062 062 025 025 026 026
065 065 066 066*1 029 029 030 030*1
063 063 064 064 027 027 028 028
061 061 062 062 025 025 026 026
065 065 066 066*1 029 029 030 030*1
*1: A data or
063 063 064 064 027 027 028 028 spare disk
061 061 062 062 025 025 026 026
is to be
065 065 066 066*1 029 029 030 030*1
063 063 064 064 027 027 028 028 installed.
061 061 062 062 025 025 026 026

Front View Front View

Fig. 3.11.2-7 (14D+2P) Data Drive/Parity Drive Expansion Sequence (3/3)

The relationship between drives installation order and RAID group number is shown in the Table
3.11.2-7.

INST03-11A-470
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-480

(viii) RAID6 (14D+2P), SBX (DKU for 2.5 inch Drive)

Relations between the installation locations of the RAID groups and the RAID group
numbers set through the SVP are shown in Table 3.11.2-8.

Table 3.11.2-8 Relation between drives installation order and RAID group number
(14D+2P, SBX) (1/2)
DKU-00 DKU-01 DKU-02 DKU-03 DKU-04 DKU-05
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
001 1-1 013 5-1 025 9-1 037 13-1 049 17-1 061 21-1
002 1-3 014 5-3 026 9-3 038 13-3 050 17-3 062 21-3
003 1-5 015 5-5 027 9-5 039 13-5 051 17-5 063 21-5
004 1-7 016 5-7 028 9-7 040 13-7 052 17-7 064 21-7
005 1-9 017 5-9 029 9-9 041 13-9 053 17-9 065 21-9
006 1-11 018 5-11 030 9-11 042 13-11 054 17-11 066 21-11
007 1-13 019 5-13 031 9-13 043 13-13 055 17-13 067 21-13
008 1-15 020 5-15 032 9-15 044 13-15 056 17-15 068 21-15
009 1-17 021 5-17 033 9-17 045 13-17 057 17-17 069 21-17
010 1-19 022 5-19 034 9-19 046 13-19 058 17-19 070 21-19
011 1-21 023 5-21 035 9-21 047 13-21 059 17-21 071 21-21
012 1-23 024 5-23 036 9-23 048 13-23 060 17-23 072 21-23
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

Table 3.11.2-8 Relation between drives installation order and RAID group number
(14D+2P, SBX) (2/2)
DKU-10 DKU-11 DKU-12 DKU-13 DKU-14 DKU-15
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
073 3-1 085 7-1 097 11-1 109 15-1 121 19-1 133 23-1
074 3-3 086 7-3 098 11-3 110 15-3 122 19-3 134 23-3
075 3-5 087 7-5 099 11-5 111 15-5 123 19-5 135 23-5
076 3-7 088 7-7 100 11-7 112 15-7 124 19-7 136 23-7
077 3-9 089 7-9 101 11-9 113 15-9 125 19-9 137 23-9
078 3-11 090 7-11 102 11-11 114 15-11 126 19-11 138 23-11
079 3-13 091 7-13 103 11-13 115 15-13 127 19-13 139 23-13
080 3-15 092 7-15 104 11-15 116 15-15 128 19-15 140 23-15
081 3-17 093 7-17 105 11-17 117 15-17 129 19-17 141 23-17
082 3-19 094 7-19 106 11-19 118 15-19 130 19-19 142 23-19
083 3-21 095 7-21 107 11-21 119 15-21 131 19-21 143 23-21
084 3-23 096 7-23 108 11-23 120 15-23 132 19-23 144 23-23
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

INST03-11A-480
 No.
073 073 073 073 073 073 073 073 085 085 085 085 085 085 085 085

DKC
073 073 073 073 073 073 073 073 085 085 085 085 085 085 085 085
Rev.0 / Dec.2013

074 074 074 074 074 074 074 074 086 086 086 086 086 086 086 086

DKU-10
DKU-11
074 074 074 074 074 074 074 074 086 086 086 086 086 086 086 086

3.11.2-8.
Hitachi Proprietary

INST03-11A-490

075 075 075 075 075 075 075 075 087 087 087 087 087 087 087 087
075 075 075 075 075 075 075 075 087 087 087 087 087 087 087 087
076 076 076 076 076 076 076 076 088 088 088 088 088 088 088 088
076 076 076 076 076 076 076 076 088 088 088 088 088 088 088 088
added.

077 077 077 077 077 077 077 077 089 089 089 089 089 089 089 089
077 077 077 077 077 077 077 077 089 089 089 089 089 089 089 089
078 078 078 078 078 078 078 078 090 090 090 090 090 090 090 090
078 078 078 078 078 078 078 078 090 090 090 090 090 090 090 090
079 079 079 079 079 079 079 079 091 091 091 091 091 091 091 091
079 079 079 079 079 079 079 079 091 091 091 091 091 091 091 091

Front View
080 080 080 080 080 080 080 080 092 092 092 092 092 092 092 092
080 080 080 080 080 080 080 080 092 092 092 092 092 092 092 092
081 081 081 081 081 081 081 081 093 093 093 093 093 093 093 093
-12
081 081 081 081 081 081 081 081 093 093 093 093 093 093 093 093
082 082 082 082 082 082 082 082 094 094 094 094 094 094 094 094
082 082 082 082 082 082 082 082 094 094 094 094 094 094 094 094
083 083 083 083 083 083 083 083 095 095 095 095 095 095 095 095
-11
2 DKC-F810I-400MCM/800MCM × 1

083 083 083 083 083 083 083 083 095 095 095 095 095 095 095 095
084 084 084 084 084 084 084 084 096 096 096 096 096 096 096 096
084*1 084*1 084*1 084*1 084*1 084*1 084*1 084*1 096*1 096*1 096*1 096*1 096*1 096*1 096*1 096*1
Model Number

-10 -00

001 001 001 001 001 001 001 001 013 013 013 013 013 013 013 013

DKC
001 001 001 001 001 001 001 001 013 013 013 013 013 013 013 013
002 002 002 002 002 002 002 002 014 014 014 014 014 014 014 014

DKU-00
DKU-01
1 DKC-F810I-300KCM/600JCM/900JCM/1R2JCM × 1

002 002 002 002 002 002 002 002 014 014 014 014 014 014 014 014
-01

003 003 003 003 003 003 003 003 015 015 015 015 015 015 015 015
003 003 003 003 003 003 003 003 015 015 015 015 015 015 015 015
004 004 004 004 004 004 004 004 016 016 016 016 016 016 016 016
004 004 004 004 004 004 004 004 016 016 016 016 016 016 016 016
-02

005 005 005 005 005 005 005 005 017 017 017 017 017 017 017 017
RACK RACK RACK RACK RACK RACK

005 005 005 005 005 005 005 005 017 017 017 017 017 017 017 017
006 006 006 006 006 006 006 006 018 018 018 018 018 018 018 018
006 006 006 006 006 006 006 006 018 018 018 018 018 018 018 018
007 007 007 007 007 007 007 007 019 019 019 019 019 019 019 019
007 007 007 007 007 007 007 007 019 019 019 019 019 019 019 019
008 008 008 008 008 008 008 008 020 020 020 020 020 020 020 020

Front View
008 008 008 008 008 008 008 008 020 020 020 020 020 020 020 020
009 009 009 009 009 009 009 009 021 021 021 021 021 021 021 021
009 009 009 009 009 009 009 009 021 021 021 021 021 021 021 021
010 010 010 010 010 010 010 010 022 022 022 022 022 022 022 022
010 010 010 010 010 010 010 010 022 022 022 022 022 022 022 022
011 011 011 011 011 011 011 011 023 023 023 023 023 023 023 023
011 011 011 011 011 011 011 011 023 023 023 023 023 023 023 023
012 012 012 012 012 012 012 012 024 024 024 024 024 024 024 024
012*1 012*1 012*1 012*1 012*1 012*1 012*1 012*1 024*1 024*1 024*1 024*1 024*1 024*1 024*1 024*1
Model Name

SFF SSD Drive

SFF Disk Drive

Fig. 3.11.2-8 (14D+2P) Data Drive/Parity Drive Expansion Sequence (1/3)

is to be
installed.
*1: A data or
spare disk
Remarks

The relationship between drives installation order and RAID group number is shown in the Table

INST03-11A-490
Copyright © 2013, Hitachi, Ltd.

(1) Make sure of the location where the RAID group is installed and that where the drive is to be
DKC810I
 097 097 097 097 097 097 097 097 109 109 109 109 109 109 109 109
097 097 097 097 097 097 097 097 109 109 109 109 109 109 109 109
Rev.0 / Dec.2013

098 098 098 098 098 098 098 098 110 110 110 110 110 110 110 110

DKU-12
DKU-13
098 098 098 098 098 098 098 098 110 110 110 110 110 110 110 110

3.11.2-8.
Hitachi Proprietary

INST03-11A-500

099 099 099 099 099 099 099 099 111 111 111 111 111 111 111 111
099 099 099 099 099 099 099 099 111 111 111 111 111 111 111 111
100 100 100 100 100 100 100 100 112 112 112 112 112 112 112 112
100 100 100 100 100 100 100 100 112 112 112 112 112 112 112 112
101 101 101 101 101 101 101 101 113 113 113 113 113 113 113 113
101 101 101 101 101 101 101 101 113 113 113 113 113 113 113 113
102 102 102 102 102 102 102 102 114 114 114 114 114 114 114 114
102 102 102 102 102 102 102 102 114 114 114 114 114 114 114 114
103 103 103 103 103 103 103 103 115 115 115 115 115 115 115 115
103 103 103 103 103 103 103 103 115 115 115 115 115 115 115 115

Front View
104 104 104 104 104 104 104 104 116 116 116 116 116 116 116 116
104 104 104 104 104 104 104 104 116 116 116 116 116 116 116 116
105 105 105 105 105 105 105 105 117 117 117 117 117 117 117 117
-12

105 105 105 105 105 105 105 105 117 117 117 117 117 117 117 117
106 106 106 106 106 106 106 106 118 118 118 118 118 118 118 118
106 106 106 106 106 106 106 106 118 118 118 118 118 118 118 118
107 107 107 107 107 107 107 107 119 119 119 119 119 119 119 119
-11

107 107 107 107 107 107 107 107 119 119 119 119 119 119 119 119
108 108 108 108 108 108 108 108 120 120 120 120 120 120 120 120
108*1 108*1 108*1 108*1 108*1 108*1 108*1 108*1 120*1 120*1 120*1 120*1 120*1 120*1 120*1 120*1
-10 -00

025 025 025 025 025 025 025 025 037 037 037 037 037 037 037 037
025 025 025 025 025 025 025 025 037 037 037 037 037 037 037 037
026 026 026 026 026 026 026 026 038 038 038 038 038 038 038 038

DKU-02
DKU-03

026 026 026 026 026 026 026 026 038 038 038 038 038 038 038 038
-01

027 027 027 027 027 027 027 027 039 039 039 039 039 039 039 039
027 027 027 027 027 027 027 027 039 039 039 039 039 039 039 039
028 028 028 028 028 028 028 028 040 040 040 040 040 040 040 040
028 028 028 028 028 028 028 028 040 040 040 040 040 040 040 040
-02

029 029 029 029 029 029 029 029 041 041 041 041 041 041 041 041
RACK RACK RACK RACK RACK RACK

029 029 029 029 029 029 029 029 041 041 041 041 041 041 041 041
030 030 030 030 030 030 030 030 042 042 042 042 042 042 042 042
030 030 030 030 030 030 030 030 042 042 042 042 042 042 042 042
031 031 031 031 031 031 031 031 043 043 043 043 043 043 043 043
031 031 031 031 031 031 031 031 043 043 043 043 043 043 043 043
032 032 032 032 032 032 032 032 044 044 044 044 044 044 044 044

Front View
032 032 032 032 032 032 032 032 044 044 044 044 044 044 044 044
033 033 033 033 033 033 033 033 045 045 045 045 045 045 045 045
033 033 033 033 033 033 033 033 045 045 045 045 045 045 045 045
034 034 034 034 034 034 034 034 046 046 046 046 046 046 046 046
034 034 034 034 034 034 034 034 046 046 046 046 046 046 046 046
035 035 035 035 035 035 035 035 047 047 047 047 047 047 047 047
035 035 035 035 035 035 035 035 047 047 047 047 047 047 047 047
036 036 036 036 036 036 036 036 048 048 048 048 048 048 048 048
036*1 036*1 036*1 036*1 036*1 036*1 036*1 036*1 048*1 048*1 048*1 048*1 048*1 048*1 048*1 048*1

Fig. 3.11.2-8 (14D+2P) Data Drive/Parity Drive Expansion Sequence (2/3)

is to be
installed.
*1: A data or
spare disk

The relationship between drives installation order and RAID group number is shown in the Table

INST03-11A-500
Copyright © 2013, Hitachi, Ltd.
DKC810I
 121 121 121 121 121 121 121 121 133 133 133 133 133 133 133 133
121 121 121 121 121 121 121 121 133 133 133 133 133 133 133 133
Rev.0 / Dec.2013

122 122 122 122 122 122 122 122 134 134 134 134 134 134 134 134

DKU-14
DKU-15
122 122 122 122 122 122 122 122 134 134 134 134 134 134 134 134

3.11.2-8.
Hitachi Proprietary

INST03-11A-510

123 123 123 123 123 123 123 123 135 135 135 135 135 135 135 135
123 123 123 123 123 123 123 123 135 135 135 135 135 135 135 135
124 124 124 124 124 124 124 124 136 136 136 136 136 136 136 136
124 124 124 124 124 124 124 124 136 136 136 136 136 136 136 136
125 125 125 125 125 125 125 125 137 137 137 137 137 137 137 137
125 125 125 125 125 125 125 125 137 137 137 137 137 137 137 137
126 126 126 126 126 126 126 126 138 138 138 138 138 138 138 138
126 126 126 126 126 126 126 126 138 138 138 138 138 138 138 138
127 127 127 127 127 127 127 127 139 139 139 139 139 139 139 139
127 127 127 127 127 127 127 127 139 139 139 139 139 139 139 139

Front View
128 128 128 128 128 128 128 128 140 140 140 140 140 140 140 140
128 128 128 128 128 128 128 128 140 140 140 140 140 140 140 140
129 129 129 129 129 129 129 129 141 141 141 141 141 141 141 141
-12

129 129 129 129 129 129 129 129 141 141 141 141 141 141 141 141
130 130 130 130 130 130 130 130 142 142 142 142 142 142 142 142
130 130 130 130 130 130 130 130 142 142 142 142 142 142 142 142
131 131 131 131 131 131 131 131 143 143 143 143 143 143 143 143
-11

131 131 131 131 131 131 131 131 143 143 143 143 143 143 143 143
132 132 132 132 132 132 132 132 144 144 144 144 144 144 144 144
132*1 132*1 132*1 132*1 132*1 132*1 132*1 132*1 144*1 144*1 144*1 144*1 144*1 144*1 144*1 144*1
-10 -00

049 049 049 049 049 049 049 049 061 061 061 061 061 061 061 061
049 049 049 049 049 049 049 049 061 061 061 061 061 061 061 061
050 050 050 050 050 050 050 050 062 062 062 062 062 062 062 062

DKU-04
DKU-05
-01

050 050 050 050 050 050 050 050 062 062 062 062 062 062 062 062
051 051 051 051 051 051 051 051 063 063 063 063 063 063 063 063
051 051 051 051 051 051 051 051 063 063 063 063 063 063 063 063
052 052 052 052 052 052 052 052 064 064 064 064 064 064 064 064
-02

052 052 052 052 052 052 052 052 064 064 064 064 064 064 064 064
RACK RACK RACK RACK RACK RACK

053 053 053 053 053 053 053 053 065 065 065 065 065 065 065 065
053 053 053 053 053 053 053 053 065 065 065 065 065 065 065 065
054 054 054 054 054 054 054 054 066 066 066 066 066 066 066 066
054 054 054 054 054 054 054 054 066 066 066 066 066 066 066 066
055 055 055 055 055 055 055 055 067 067 067 067 067 067 067 067
055 055 055 055 055 055 055 055 067 067 067 067 067 067 067 067
056 056 056 056 056 056 056 056 068 068 068 068 068 068 068 068

Front View
056 056 056 056 056 056 056 056 068 068 068 068 068 068 068 068
057 057 057 057 057 057 057 057 069 069 069 069 069 069 069 069
057 057 057 057 057 057 057 057 069 069 069 069 069 069 069 069
058 058 058 058 058 058 058 058 070 070 070 070 070 070 070 070
058 058 058 058 058 058 058 058 070 070 070 070 070 070 070 070
059 059 059 059 059 059 059 059 071 071 071 071 071 071 071 071
059 059 059 059 059 059 059 059 071 071 071 071 071 071 071 071
060 060 060 060 060 060 060 060 072 072 072 072 072 072 072 072
060*1 060*1 060*1 060*1 060*1 060*1 060*1 060*1 072*1 072*1 072*1 072*1 072*1 072*1 072*1 072*1

Fig. 3.11.2-8 (14D+2P) Data Drive/Parity Drive Expansion Sequence (3/3)

is to be
installed.
*1: A data or
spare disk

The relationship between drives installation order and RAID group number is shown in the Table

INST03-11A-510
Copyright © 2013, Hitachi, Ltd.
DKC810I
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-520

(ix) RAID6 (14D+2P), FBX (DKU for FMD)

Relations between the installation locations of the RAID groups and the RAID group
numbers set through the SVP are shown in Table 3.11.2-9.

Table 3.11.2-9 Relation between drives installation order and RAID group number
(14D+2P, FBX) (1/2)
DKU-00 DKU-01 DKU-02 DKU-03 DKU-04 DKU-05
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
001 1-1 004 5-1 007 9-1 010 13-1 013 17-1 016 21-1
002 1-3 005 5-3 008 9-3 011 13-3 014 17-3 017 21-3
003 1-5 006 5-5 009 9-5 012 13-5 015 17-5 018 21-5
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

Table 3.11.2-9 Relation between drives installation order and RAID group number
(14D+2P, FBX) (2/2)
DKU-10 DKU-11 DKU-12 DKU-13 DKU-14 DKU-15
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
019 3-1 022 7-1 025 11-1 028 15-1 031 19-1 034 23-1
020 3-3 023 7-3 026 11-3 029 15-3 032 19-3 035 23-3
021 3-5 024 7-5 027 11-5 030 15-5 033 19-5 036 23-5
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

INST03-11A-520
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-530

(1) Make sure of the location where the RAID group is installed and that where the drive is to be
added.
No. Model Number Model Name Remarks
1 DKC-F810I-1R6FM/3R2FM × 16 Flash Module Drive FMD

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-01
005 006 006*1
004 004 005
005 006 006*1
004 004 005
005 006 006*1
004 004 005 DKU-03 DKU-05
005 006 006*1
004 004 005 011 012 012*1 017 018 018*1
005 006 006*1 010 010 011 016 016 017
004 004 005 011 012 012*1 017 018 018*1
005 006 006*1 010 010 011 016 016 017
004 004 005 011 012 012*1 017 018 018*1
005 006 006*1 010 010 011 016 016 017
004 004 005 011 012 012*1 017 018 018*1
005 006 006*1 010 010 011 016 016 017
004 004 005 011 012 012*1 017 018 018*1
010 010 011 016 016 017
DKU-00 011 012 012*1 017 018 018*1
010 010 011 016 016 017
012 003 003*1
001 001 002 011 012 012*1 017 018 018*1
002 003 003*1 010 010 011 016 016 017
011 012 012*1 017 018 018*1
001 001 002 010 010 011 016 016 017
012 003 003*1
001 001 002 DKU-02 DKU-04
002 003 003*1
001 001 002 008 009 009*1 014 015 015*1
007 007 008 013 013 014
012 003 003*1 008 009 009*1 014 015 015*1
001 001 002 007 007 008 013 013 014
002 003 003*1 008 009 009*1 014 015 015*1
001 001 002 007 007 008 013 013 014
012 003 003*1 008 009 009*1 014 015 015*1
001 001 002 007 007 008 013 013 014
002 003 003*1 008 009 009*1 014 015 015*1
001 001 002 007 007 008 013 013 014
008 009 009*1 014 015 015*1
DKC-0 007 007 008 013 013 014 *1: A data or
008 009 009*1 014 015 015*1 spare disk
007 007 008 013 013 014
008 009 009*1 014 015 015*1 is to be
007 007 008 013 013 014
installed.

Front View

Fig. 3.11.2-9 (14D+2P) Data Drive/Parity Drive Expansion Sequence (1/2)

The relationship between drives installation order and RAID group number is shown in the Table
3.11.2-9.
INST03-11A-530
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-540

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-11
023 024 024*1
022 022 023
023 024 024*1
022 022 023
023 024 024*1
022 022 023
DKU-15 DKU-13 023 024 024*1
035 036 036*1 029 030 030*1 022 022 023
034 034 035 028 028 029 023 024 024*1
035 036 036*1 029 030 030*1 022 022 023
034 034 035 028 028 029 023 024 024*1
035 036 036*1 029 030 030*1 022 022 023
034 034 035 028 028 029 023 024 024*1
035 036 036*1 029 030 030*1 022 022 023
034 034 035 028 028 029 023 024 024*1
035 036 036*1 029 030 030*1 022 022 023
034 034 035 028 028 029
035 036 036*1 029 030 030*1 DKU-10
034 034 035 028 028 029 020 021 021*1
035 036 036*1 029 030 030*1 019 019 020
034 034 035 028 028 029 020 021 021*1
035 036 036*1 029 030 030*1 019 019 020
034 034 035 028 028 029
020 021 021*1
DKU-14 DKU-12 019 019 020
020 021 021*1
032 033 033*1 026 027 027*1 019 019 020
031 031 032 025 025 026
032 033 033*1 026 027 027*1 020 021 021*1
031 031 032 025 025 026 019 019 020
032 033 033*1 026 027 027*1 020 021 021*1
031 031 032 025 025 026 019 019 020
032 033 033*1 026 027 027*1 020 021 021*1
031 031 032 025 025 026 019 019 020
032 033 033*1 026 027 027*1 020 021 021*1
031 031 032 025 025 026 019 019 020
032 033 033*1 026 027 027*1
031 031 032 025 025 026 DKC-1 *1: A data or
032 033 033*1 026 027 027*1
031 031 032 025 025 026 spare disk
032 033 033*1 026 027 027*1 is to be
031 031 032 025 025 026
installed.

Front View

Fig. 3.11.2-9 (14D+2P) Data Drive/Parity Drive Expansion Sequence (2/2)

The relationship between drives installation order and RAID group number is shown in the Table
3.11.2-9.

INST03-11A-540
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-550

(x) Spare Drive, UBX (DKU for 3.5 inch Drive)

Table 3.11.2-10 Relation between Drive installation order and Spare Drive number
(1/4)
DKU-00 DKU-01 DKU-02 DKU-03
Installation B4 Spare Installation B4 Spare Installation B4 Spare Installation B4 Spare
Order No. drive No. Order No. drive No. Order No. drive No. Order No. drive No.
001 1st Spare1 009 2nd Spare1 017 5th Spare1 025 6th Spare1
002 1st Spare2 010 2nd Spare2 018 5th Spare2 026 6th Spare2
003 1st Spare3 011 2nd Spare3 019 5th Spare3 027 6th Spare3
004 1st Spare4 012 2nd Spare4 020 5th Spare4 028 6th Spare4
005 1st Spare5 013 2nd Spare5 021 5th Spare5 029 6th Spare5
006 1st Spare6 014 2nd Spare6 022 5th Spare6 030 6th Spare6
007 1st Spare7 015 2nd Spare7 023 5th Spare7 031 6th Spare7
008 1st Spare8 016 2nd Spare8 024 5th Spare8 032 6th Spare8

Table 3.11.2-10 Relation between Drive installation order and Spare Drive number
(2/4)
DKU-04 DKU-05
Installation B4 Spare Installation B4 Spare
Order No. drive No. Order No. drive No.
033 9th Spare1 041 10st Spare1
034 9th Spare2 042 10st Spare2
035 9th Spare3 043 10st Spare3
036 9th Spare4 044 10st Spare4
037 9th Spare5 045 10st Spare5
038 9th Spare6 046 10st Spare6
039 9th Spare7 047 10st Spare7
040 9th Spare8 048 10st Spare8

INST03-11A-550
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-560

Table 3.11.2-10 Relation between Drive installation order and Spare Drive number
(3/4)
DKU-10 DKU-11 DKU-12 DKU-13
Installation B4 Spare Installation B4 Spare Installation B4 Spare Installation B4 Spare
Order No. drive No. Order No. drive No. Order No. drive No. Order No. drive No.
049 3rd Spare1 057 4th Spare1 065 7th Spare1 073 8th Spare1
050 3rd Spare2 058 4th Spare2 066 7th Spare2 074 8th Spare2
051 3rd Spare3 059 4th Spare3 067 7th Spare3 075 8th Spare3
052 3rd Spare4 060 4th Spare4 068 7th Spare4 076 8th Spare4
053 3rd Spare5 061 4th Spare5 069 7th Spare5 077 8th Spare5
054 3rd Spare6 062 4th Spare6 070 7th Spare6 078 8th Spare6
055 3rd Spare7 063 4th Spare7 071 7th Spare7 079 8th Spare7
056 3rd Spare8 064 4th Spare8 072 7th Spare8 080 8th Spare8

Table 3.11.2-10 Relation between Drive installation order and Spare Drive number
(4/4)
DKU-14 DKU-15
Installation B4 Spare Installation B4 Spare
Order No. drive No. Order No. drive No.
081 11th Spare1 089 12th Spare1
082 11th Spare2 090 12th Spare2
083 11th Spare3 091 12th Spare3
084 11th Spare4 092 12th Spare4
085 11th Spare5 093 12th Spare5
086 11th Spare6 094 12th Spare6
087 11th Spare7 095 12th Spare7
088 11th Spare8 096 12th Spare8

INST03-11A-560
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-570

No. Model Number Model Name Data and Parity

1 DKC-F810I-3R0H3M/4R0H3M × 1 LFF Disk Drive Spare drive

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-11 DKU-01
064 016

063 015

062 014

061 013

060 012

059 011

058 010

057 009

DKU-10 DKU-00
056 008

055 007

054 006

053 005

052 004

051
003

050 002

049 001

*1: A data or
DKC-1 DKC-0 spare disk
is to be
installed.

Front View Front View

Fig. 3.11.2-10 Spare Drive Expansion Sequence (1/3)

INST03-11A-570
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-580

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-13 DKU-03
080 032

079 031

078 030

077 029

076 028

075 027

074 026

073 025

DKU-12 DKU-02
072 024

071 023

070 022

069 021

068 020

067 019

066 018
*1: A data or
spare disk
is to be
065 017
installed.

Front View Front View

Fig. 3.11.2-10 Spare Drive Expansion Sequence (2/3)

INST03-11A-580
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-590

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-15 DKU-05
096 048

095 047

094 046

093 045

092 044

091 043

090 042

089 041

DKU-14 DKU-04
088 040

087 039

086 038

085 037

084 036

083 035

082 034
*1: A data or
spare disk
is to be
081 033
installed.

Front View Front View

Fig. 3.11.2-10 Spare Drive Expansion Sequence (3/3)

INST03-11A-590
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-600

(xi) Spare Drive, SBX (DKU for 2.5 inch Drive)

Table 3.11.2-11 Relation between Drive installation order and Spare Drive number
(1/4)
DKU-00 DKU-01 DKU-02 DKU-03
Installation B4 Spare Installation B4 Spare Installation B4 Spare Installation B4 Spare
Order No. drive No. Order No. drive No. Order No. drive No. Order No. drive No.
001 1st Spare1 009 2nd Spare1 017 5th Spare1 025 6th Spare1
002 1st Spare2 010 2nd Spare2 018 5th Spare2 026 6th Spare2
003 1st Spare3 011 2nd Spare3 019 5th Spare3 027 6th Spare3
004 1st Spare4 012 2nd Spare4 020 5th Spare4 028 6th Spare4
005 1st Spare5 013 2nd Spare5 021 5th Spare5 029 6th Spare5
006 1st Spare6 014 2nd Spare6 022 5th Spare6 030 6th Spare6
007 1st Spare7 015 2nd Spare7 023 5th Spare7 031 6th Spare7
008 1st Spare8 016 2nd Spare8 024 5th Spare8 032 6th Spare8

Table 3.11.2-11 Relation between Drive installation order and Spare Drive number
(2/4)
DKU-04 DKU-05
Installation B4 Spare Installation B4 Spare
Order No. drive No. Order No. drive No.
033 9th Spare1 041 10st Spare1
034 9th Spare2 042 10st Spare2
035 9th Spare3 043 10st Spare3
036 9th Spare4 044 10st Spare4
037 9th Spare5 045 10st Spare5
038 9th Spare6 046 10st Spare6
039 9th Spare7 047 10st Spare7
040 9th Spare8 048 10st Spare8

INST03-11A-600
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-610

Table 3.11.2-11 Relation between Drive installation order and Spare Drive number
(3/4)
DKU-10 DKU-11 DKU-12 DKU-13
Installation B4 Spare Installation B4 Spare Installation B4 Spare Installation B4 Spare
Order No. drive No. Order No. drive No. Order No. drive No. Order No. drive No.
049 3rd Spare1 057 4th Spare1 065 7th Spare1 073 8th Spare1
050 3rd Spare2 058 4th Spare2 066 7th Spare2 074 8th Spare2
051 3rd Spare3 059 4th Spare3 067 7th Spare3 075 8th Spare3
052 3rd Spare4 060 4th Spare4 068 7th Spare4 076 8th Spare4
053 3rd Spare5 061 4th Spare5 069 7th Spare5 077 8th Spare5
054 3rd Spare6 062 4th Spare6 070 7th Spare6 078 8th Spare6
055 3rd Spare7 063 4th Spare7 071 7th Spare7 079 8th Spare7
056 3rd Spare8 064 4th Spare8 072 7th Spare8 080 8th Spare8

Table 3.11.2-11 Relation between Drive installation order and Spare Drive number
(4/4)
DKU-14 DKU-15
Installation B4 Spare Installation B4 Spare
Order No. drive No. Order No. drive No.
081 11th Spare1 089 12th Spare1
082 11th Spare2 090 12th Spare2
083 11th Spare3 091 12th Spare3
084 11th Spare4 092 12th Spare4
085 11th Spare5 093 12th Spare5
086 11th Spare6 094 12th Spare6
087 11th Spare7 095 12th Spare7
088 11th Spare8 096 12th Spare8

INST03-11A-610
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-620

No. Model Number Model Name Remarks

1 DKC-F810I-300KCM/600JCM/900JCM/1R2JCM × 1 SFF Disk Drive Spare Drive
2 DKC-F810I-400MCM/800MCM × 1 SFF SSD Drive Spare Drive

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-11 DKU-01
064

016
063

015
062

014
061

013
060

012
059

011
058

010
057

009
DKU-10 DKU-00
056

008
055

007
054

006
053

005
052

004
051

003
050

002
049

001

*1: A data or
DKC-1 DKC-0 spare disk
is to be
installed.

Front View Front View

Fig. 3.11.2-11 Spare Drive Expansion Sequence (1/3)

INST03-11A-620
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-630

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-13 DKU-03

080

032
079

031
078

030
077

029
076

028
075

027
074

026
073

025
DKU-12 DKU-02
072

024
071

023
070

022
069

021
068

020
067

019

*1: A data or
066

018

spare disk
is to be
065

017

installed.

Front View Front View

Fig. 3.11.2-11 Spare Drive Expansion Sequence (2/3)

INST03-11A-630
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-640

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-15 DKU-05

096

048
095

047
094

046
093

045
092

044
091

043
090

042
089

041
DKU-14 DKU-04
088

040
087

039
086

038
085

037
084

036
083

035

*1: A data or
082

034

spare disk
is to be
081

033

installed.

Front View Front View

Fig. 3.11.2-11 Spare Drive Expansion Sequence (3/3)

INST03-11A-640
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-650

(xii) Spare Drive, FBX (DKU for FMD)

Table 3.11.2-12 Relation between Drive installation order and Spare Drive number
(1/4)
DKU-00 DKU-01 DKU-02 DKU-03
Installation B4 Spare Installation B4 Spare Installation B4 Spare Installation B4 Spare
Order No. drive No. Order No. drive No. Order No. drive No. Order No. drive No.
001 1st Spare1 009 2nd Spare1 017 5th Spare1 025 6th Spare1
002 1st Spare2 010 2nd Spare2 018 5th Spare2 026 6th Spare2
003 1st Spare3 011 2nd Spare3 019 5th Spare3 027 6th Spare3
004 1st Spare4 012 2nd Spare4 020 5th Spare4 028 6th Spare4
005 1st Spare5 013 2nd Spare5 021 5th Spare5 029 6th Spare5
006 1st Spare6 014 2nd Spare6 022 5th Spare6 030 6th Spare6
007 1st Spare7 015 2nd Spare7 023 5th Spare7 031 6th Spare7
008 1st Spare8 016 2nd Spare8 024 5th Spare8 032 6th Spare8

Table 3.11.2-12 Relation between Drive installation order and Spare Drive number
(2/4)
DKU-04 DKU-05
Installation B4 Spare Installation B4 Spare
Order No. drive No. Order No. drive No.
033 9th Spare1 041 10st Spare1
034 9th Spare2 042 10st Spare2
035 9th Spare3 043 10st Spare3
036 9th Spare4 044 10st Spare4
037 9th Spare5 045 10st Spare5
038 9th Spare6 046 10st Spare6
039 9th Spare7 047 10st Spare7
040 9th Spare8 048 10st Spare8

INST03-11A-650
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-660

Table 3.11.2-12 Relation between Drive installation order and Spare Drive number
(3/4)
DKU-10 DKU-11 DKU-12 DKU-13
Installation B4 Spare Installation B4 Spare Installation B4 Spare Installation B4 Spare
Order No. drive No. Order No. drive No. Order No. drive No. Order No. drive No.
049 3rd Spare1 057 4th Spare1 065 7th Spare1 073 8th Spare1
050 3rd Spare2 058 4th Spare2 066 7th Spare2 074 8th Spare2
051 3rd Spare3 059 4th Spare3 067 7th Spare3 075 8th Spare3
052 3rd Spare4 060 4th Spare4 068 7th Spare4 076 8th Spare4
053 3rd Spare5 061 4th Spare5 069 7th Spare5 077 8th Spare5
054 3rd Spare6 062 4th Spare6 070 7th Spare6 078 8th Spare6
055 3rd Spare7 063 4th Spare7 071 7th Spare7 079 8th Spare7
056 3rd Spare8 064 4th Spare8 072 7th Spare8 080 8th Spare8

Table 3.11.2-12 Relation between Drive installation order and Spare Drive number
(4/4)
DKU-14 DKU-15
Installation B4 Spare Installation B4 Spare
Order No. drive No. Order No. drive No.
081 11th Spare1 089 12th Spare1
082 11th Spare2 090 12th Spare2
083 11th Spare3 091 12th Spare3
084 11th Spare4 092 12th Spare4
085 11th Spare5 093 12th Spare5
086 11th Spare6 094 12th Spare6
087 11th Spare7 095 12th Spare7
088 11th Spare8 096 12th Spare8

INST03-11A-660
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-670

No. Model Number Model Name Data and Parity

1 DKC-F810I-1R6FM/3R2FM × 1 Flash Module Drive Spare Drive

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-01
016
012

015
011 DKU-03 DKU-05
032 048
014
028 044
010
031 047
013
027 043
009
030 046
DKU-00 026 042
008
029 045
004
025 041
007
DKU-02 DKU-04
003
024 040
006 020 036
002 023 039

005 019 035

001 022 038

018 034
DKC-0 *1: A data or
021 037
spare disk
017 033 is to be
installed.

Front View

Fig. 3.11.2-12 Spare Drive Expansion Sequence (1/2)

INST03-11A-670
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-680

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-11
064
060

063
DKU-15 DKU-13 059
096 080
062
092 076
058
095 079
061
091 075
057
094 078
090 074
DKU-10
056
093 077
052
089 073
055
DKU-14 DKU-12
051
088 072
084 068 054

087 071 050

083 067 053

086 070 049
082 066
DKC-1 *1: A data or
085 069 spare disk
081 065 is to be
installed.

Front View

Fig. 3.11.2-12 Spare Drive Expansion Sequence (2/2)

INST03-11A-680
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-690

3-2 Checking the condition of the drive

a. Check the condition of the drive before installing it.

Drive (HDD/SSD)
Main Edge Connector

NOTICE: Check that the main edge connector of the drive

(HDD/SSD/FMD) has no deformation, damage or
sticking of dust before installing the drive.

Drive (FMD)

INST03-11A-690
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-700

3-3 Installing the drives

NOTICE: When two or more drives are inserted at the same time, the already operating
drives might be blocked.
Insert the drives one by one at a second (*1) interval.
Don’t insert the drive that is not defined in the configuration.
*1: Interval of time necessary for stabilizing the voltage of the back board after
a drive insertion.

NOTICE: Be sure to wear your wrist strap and attach to ground prior to performing the
following work. This will ensure that the IC and LSI on the PCB are protected
from static electricity.

INST03-11A-700
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-710

In case of UBX

NOTICE: Since the Drive is a precision component, handle it very carefully not to apply a
vibration or shock to it.

a. Remove the dummy (drive) from the position installing the drive.
b. Open the handle fully and fit the drive in the guide rail and slide it in the direction shown by
the arrow not to give a shock.
NOTE: When handling the drive, hold the rail side because the shield spring is subject to
breakage.
c. Push the drive in until it reaches the position where a hook of the handle can be entered into
the square hole on a frame.
d. Pull the stopper lightly and close the handle, and then press the stopper to have the lock on.
If the handle is closed in the state where the hook of the handle cannot enter into the square
hole, the drive cannot be installed correctly because it runs into the frame of the drive
chassis.

Guide Rail

Dummy (Drive)

Square Hole Drive

Hook
Stopper
Drive Front View of Rail
UBX

Shield Spring
Handle

Fig. 3.11.2-13 Installation of Drives (In case of UBX)

INST03-11A-710
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-720

In case of SBX

NOTICE: Since the Drive is a precision component, handle it very carefully not to apply a
vibration or shock to it.

a. Remove the dummy (drive) from the position installing the drive.
b. Fit the drive in the guide rail and slide it in the direction shown by the arrow not to give a
shock.
c. Push the drive in until it reaches the position where a hook of the handle can be entered into
the square hole at the lower part of a frame on the front side of the drive box.
d. Raise the stopper, which has been tilted toward you, and then press the stopper to have the
lock on.
If the handle is raised in the state where the hook of the handle cannot enter into each hole,
the drive cannot be installed correctly because it runs into the frame of the drive chassis.

Dummy (Drive)

Front View of
SBX

Drive Drive

Handle
Guide Rail

Hook

Fig. 3.11.2-14 Installation of Drives (In case of SBX)

INST03-11A-720
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-730

In case of FBX

NOTICE: Be sure to detach the tape and remove the connector cover when installing the FMD.
Installing the FMD with the connector cover attached may cause equipment damage
or failure.
Connector Cover
Tape

Drive (FMD) Tape

INST03-11A-730
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-740

a. Remove the Dummy FMD from the installing position of a drive.

Release the hook while pressing the lock to the left to pull the Dummy FMD toward you.
b. Open the handle fully and fit the drive in the guide rail and slide it in the direction shown by
the arrow not to give a shock.
NOTE: When handling the drive, hold the rail side because the shield spring is subject to
breakage.
c. Push the drive in until it reaches the position where a hook of the handle can be entered into
the square hole on a frame.
d. Pull the stopper lightly and close the handle, and then press the stopper to have the lock on.
If the handle is closed in the state where the hook of the handle cannot enter into the square
hole, the drive cannot be installed correctly because it runs into the frame of the drive
chassis.

FBX

Dummy FMD

Lock

Hook

FBX

Guide Rail

Square Hole

Drive (FMD)

Hook

Rail Stopper
Shield Spring Handle

Fig. 3.11.2-15 Installation of Drive (In case of FBX)

INST03-11A-740
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-750

4. SVP post procedure

(1) <Check that hardware components are installed>
Select (CL) [OK] after making sure that all
hardware components are installed correctly in
response to “Insert the PDEV on the storage
system. Select [OK] when the installation has
completed.”.
NOTE: On page INST03-11A-140 (13), it
advances to (3)-1 when a Quick Format is selected (CL).

(2) <DKU PATH INLINE>

When DKA is installed, “DKU PATH INLINE is now running...” is displayed.

(3) <LDEV FORMAT>

“Formatting logical devices...” is displayed when Parity Group is defined.

(3)-1 <QUICK FORMAT>

“Preparing Quick Format logical devices...” is displayed when Parity Group is defined.

INST03-11A-750
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-760

(4) <End of system update processing>

“Renewal process has completed. Please check
storage system status.” is displayed when
recovery processing on all installed
components is completed. Select (CL) [OK] in
response to this message.

(4)-1 <QUICK FORMAT>

Refer to the logical device window in the “Maintenance” window to check that the Quick Format
is in progress. (SVP03-06-10 through 100)

INST03-11A-760
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11A-770

(5)
Execute an operation for backing up the
configuration information.
Prepare the removable media for backup and
insert the media.
Please select (CL) the [Refresh] button, and
update drive information.
Select (CL) the drive and the PC in which the
media was inserted. Select (CL) the [OK]
button.
NOTE: For the procedure of backing up the
configuration information to a CD-R,
see page MICRO07-190.

(6)
When this procedure is completed, the message
“Please remove the Config media.” is displayed.
Remove the configuration information media,
select (CL) [OK].

(7)
After the procedure is completed, return to
‘Install’.
Select (CL) [File]-[Exit].

(8) <Mode Change>

Change the mode to View Mode.

Return to the work table (INST02-50) and perform rest of the works.

INST03-11A-770
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-10

3.11.3 When performing addition of the DKA and Device Interface Cable
(DKC-F810I-SCA/CC1/CC2)

1. When you need to install DKC-F810I-CC2, attach the location labels to the cables.
When you do not need to install DKC-F810I-CC2, go to Procedure 2.
a. Attach 16 location labels to 8 cables. Choose location labels from Labels (Address) and
Labels (Address) 2. See Fig. 3.11.3-1, Table 3.11.3-1, Table 3.11.3-2, Table 3.11.3-3 and
Table 3.11.3-4.
b. Stick the Label (Protect) around the attached location labels.

Location Label  Location Label 

80mm 80mm

Cable

[Label Attachment Example]

Cable

Location Label

Edge

Label (Protect)

 Attach the location label to the MFC cable.

 Attach the Label (Protect) to the location label with its edge aligned with the location label.
 Stick the Label (Protect) around the location label so that the location label is not torn off.

Fig. 3.11.3-1 Attachment of Location Labels

Table 3.11.3-1 Location Label List (DKC-0(DKA-1PA/2PA) – DKU-00)

No. Connection Source (DKC-0) Connection Destination (DKU-00)
Part Name Location Label Color Part Name Location Label Color
Label  UBX/SBX FBX Label
1 DKA-1PA CL1 1PA-0 White/Black SSW000-1 SSW000-1 CL1 0-0 White/Black
2 DKA-1PA CL1 1PA-1 White/Brown SSW002-1 SSW001-1 CL1 2-0 White/Red
3 DKA-1PA CL1 1PA-2 White/Red SSW004-1 SSW002-1 CL1 4-0 White/Yellow
4 DKA-1PA CL1 1PA-3 White/Orange SSW006-1 SSW003-1 CL1 6-0 White/Blue
5 DKA-2PA CL2 2PA-0 Yellow/Black SSW001-2 SSW000-2 CL2 1-0 Yellow/Brown
6 DKA-2PA CL2 2PA-1 Yellow/Brown SSW003-2 SSW001-2 CL2 3-0 Yellow/Orange
7 DKA-2PA CL2 2PA-2 Yellow/Red SSW005-2 SSW002-2 CL2 5-0 Yellow/Green
8 DKA-2PA CL2 2PA-3 Yellow/Orange SSW007-2 SSW003-2 CL2 7-0 Yellow/Purple

INST03-11B-10
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-20

Table 3.11.3-2 Location Label List (DKC-0(DKA-1PB/2PB) – DKU-00)

No. Connection Source (DKC-0) Connection Destination (DKU-00)
Part Name Location Label Color Part Name Location Label Color
Label  UBX/SBX FBX Label
1 DKA-1PB CL1 1PB-0 White/Black SSW001-1 SSW000-1 CL1 1-0 White/Brown
2 DKA-1PB CL1 1PB-1 White/Brown SSW003-1 SSW001-1 CL1 3-0 White/Orange
3 DKA-1PB CL1 1PB-2 White/Red SSW005-1 SSW002-1 CL1 5-0 White/Green
4 DKA-1PB CL1 1PB-3 White/Orange SSW007-1 SSW003-1 CL1 7-0 White/Purple
5 DKA-2PB CL2 2PB-0 Yellow/Black SSW000-2 SSW000-2 CL2 0-0 Yellow/Black
6 DKA-2PB CL2 2PB-1 Yellow/Brown SSW002-2 SSW001-2 CL2 2-0 Yellow/Red
7 DKA-2PB CL2 2PB-2 Yellow/Red SSW004-2 SSW002-2 CL2 4-0 Yellow/Yellow
8 DKA-2PB CL2 2PB-3 Yellow/Orange SSW006-2 SSW003-2 CL2 6-0 Yellow/Blue

Table 3.11.3-3 Location Label List (DKC-1(DKA-1PG/2PG) – DKU-10)

No. Connection Source (DKC-1) Connection Destination (DKU-10)
Part Name Location Label Color Part Name Location Label Color
Label  UBX/SBX FBX Label
1 DKA-1PG CL1 1PG-0 White/Black SSW100-1 SSW100-1 CL1 0-0 White/Black
2 DKA-1PG CL1 1PG-1 White/Brown SSW102-1 SSW101-1 CL1 2-0 White/Red
3 DKA-1PG CL1 1PG-2 White/Red SSW104-1 SSW102-1 CL1 4-0 White/Yellow
4 DKA-1PG CL1 1PG-3 White/Orange SSW106-1 SSW103-1 CL1 6-0 White/Blue
5 DKA-2PG CL2 2PG-0 Yellow/Black SSW101-2 SSW100-2 CL2 1-0 Yellow/Brown
6 DKA-2PG CL2 2PG-1 Yellow/Brown SSW103-2 SSW101-2 CL2 3-0 Yellow/Orange
7 DKA-2PG CL2 2PG-2 Yellow/Red SSW105-2 SSW102-2 CL2 5-0 Yellow/Green
8 DKA-2PG CL2 2PG-3 Yellow/Orange SSW107-2 SSW103-2 CL2 7-0 Yellow/Purple

Table 3.11.3-4 Location Label List (DKC-1(DKA-1PH/2PH) – DKU-10)

No. Connection Source (DKC-1) Connection Destination (DKU-10)
Part Name Location Label Color Part Name Location Label Color
Label  UBX/SBX FBX Label
1 DKA-1PH CL1 1PH-0 White/Black SSW101-1 SSW100-1 CL1 1-0 White/Brown
2 DKA-1PH CL1 1PH-1 White/Brown SSW103-1 SSW101-1 CL1 3-0 White/Orange
3 DKA-1PH CL1 1PH-2 White/Red SSW105-1 SSW102-1 CL1 5-0 White/Green
4 DKA-1PH CL1 1PH-3 White/Orange SSW107-1 SSW103-1 CL1 7-0 White/Purple
5 DKA-2PH CL2 2PH-0 Yellow/Black SSW100-2 SSW100-2 CL2 0-0 Yellow/Black
6 DKA-2PH CL2 2PH-1 Yellow/Brown SSW102-2 SSW101-2 CL2 2-0 Yellow/Red
7 DKA-2PH CL2 2PH-2 Yellow/Red SSW104-2 SSW102-2 CL2 4-0 Yellow/Yellow
8 DKA-2PH CL2 2PH-3 Yellow/Orange SSW106-2 SSW103-2 CL2 6-0 Yellow/Blue

INST03-11B-20
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-30

2. Setting up the New Device Structure Information

(1) <Mode Change>
Change the mode to Modify Mode.
Select (CL) [Install].

(2) <Start the ‘Menu Dialog’ screen>

Select (CL) [Change Configuration].

(3) <Start Device Structure Setup screen>

Select (CL) [Installation] in the “Menu
Dialog” dialog box and select (CL) [OK].

(4) <Select a changed part>

Select (CL) [DKA], and select (CL) [OK].

INST03-11B-30
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-40

(5) <Update Configuration Information>

Select (CL) [CHA/DKA/MPB] in the ‘DKC
Configuration’ screen.
Go to Step (6).

After confirming input items, select (CL) the

[>>Next] button.
Go to Step (7).
In the case of selecting (CL) [Cancel], this
operation procedure terminates.

INST03-11B-40
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-50

(6) <Setting DKA>

Define the DKA in the ‘CHA/DKA/MPB
Configuration’ screen. Select (CL) the location
to be added, and then select (CL) the
[Change...].
Go to Step (6)-1.
After confirming input items, select (CL) the
[OK] button.
Go back to Step (5).

(6)-1 <Select DKA>

Define the DKA in the ‘CHA/DKA/MPB
Define’ screen. After setting, select (CL)
[OK].
Go back to Step (6).

INST03-11B-50
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-60

(7) <Wear a wrist strap>

Select (CL) [OK] in response to “To prevent
serious failures caused by the static electrical
charge, be sure to wear a wrist strap on your
wrist and connect the earth clip attached on the
other side of the wrist strap to the chassis
frame (metal part) before starting operation.”.

(7)-1 <Confirm wearing wrist strap>

In response to a message, “Did you put on a
wrist strap on your wrist?”.
Select [Yes] when wrist strap is on your wrist.
Select [No] when there is no wrist strap on your
wrist.
When [No] is selected (CL), go to Step (7)-2.

(7)-2
In response to a message, “This operation
cannot be excuted, because the wrist strap has
not been worn. Do you want to stop this
process?
[Yes]: This processing will be stopped.
[No]: This confirming message will appear.”
When [Yes] is selected (CL), the routine is
returned to Step (2) on page INST03-11B-30.
When [No] is selected (CL), returned to Step (7).

INST03-11B-60
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-70

(8) <Start installation>

Select (CL) [Yes] in response to “After you
select [Yes], you cannot cancel this operation.
Are you sure you want to continue this
operation? (Note) Do not insert the
components for upgrading the system at this
time.”.

When [No] is selected (CL), returns to

INST03-11B-30 Step (2).

INST03-11B-70
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-80

3. SVP Pre-Procedure (Cluster 1)

(1) <Check SAS cable connection>
“Disconnect the SAS cables from the SSW
(OUT0) connected with DKA (DKA-nnn) of
cluster-1, connect the SAS cables to the
installation target DKA (DKA-nnn), and then
select [OK].”is displayed.

NOTE: This message is displayed when

changing from the Standard Model to the High Performance Model.

NOTE: Connect the cables of Blinking LED.

SSW (UBX / SBX)

SSWx07-1
SSWx05-1
SSWx03-1
SSWx01-1

SSWx06-1
SSWx04-1
SSWx02-1
SSWx00-1

SSW (FBX)

SSWx03-1
SSWx02-1
SSWx01-1
SSWx00-1

INST03-11B-80
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-90

(2) <Connect SAS cable>

When you need to remove Device Interface Cable CC1 (DKC-F810I-CC1) from
DKU-00(UBX/SBX)
(2)-1 Disconnect the cables from the SSWs in the DKU-00. (Refer to Fig. 3.11.3-2 and Fig.
3.11.3-3.)
(2)-2 Attach the caps to the disconnected cables.

CAUTION
A serious failure occurs if a wrong cable or connector is removed.
Since a label bearing a connection destination is affixed on each cable or connector to be
removed, work very carefully referring to it and the wiring diagram.

SSW003-1

CL1 3-0

SSW002-1

CL1 2-1

Rear View of SSW001-1

DKU-00(UBX/SBX)

SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 CL1 1-0
Front View of SSW

Work after disconnecting SSW000-1

the cables

Cap
CL1 0-1

Cable

Fig. 3.11.3-2 Disconnection of Cables (UBX/SBX_CC1_CL1_L)

INST03-11B-90
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-100

CAUTION
A serious failure occurs if a wrong cable or connector is removed.
Since a label bearing a connection destination is affixed on each cable or connector to be
removed, work very carefully referring to it and the wiring diagram.

SSW007-1

CL1 7-0

SSW006-1

CL1 6-1

Rear View of SSW005-1

DKU-00(UBX/SBX)

SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 CL1 5-0
Front View of SSW

Work after disconnecting SSW004-1

the cables

Cap
CL1 4-1

Cable

Fig. 3.11.3-3 Disconnection of Cables (UBX/SBX_CC1_CL1_U)

INST03-11B-100
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-110

When you need to remove Device Interface Cable CC1 (DKC-F810I-CC1) from DKU-00(FBX)
(2)-1 Disconnect the cables from the SSWs in the DKU-00.
(2)-2 Attach the caps to the disconnected cables.

CAUTION
A serious failure occurs if a wrong cable or connector is removed.
Since a label bearing a connection destination is affixed on each cable or connector to be
removed, work very carefully referring to it and the wiring diagram.

CL1 6-1 SSW003-1

CL1 7-0

Rear View of DKU-00(FBX) CL1 4-1 SSW002-1

SSWxyz-1 SSWxyz-2
CL1 5-0
-0 -1 -2 -0 -1 -2 -0 -1 -2 -0 -1 -2
Front View of SSW
CL1 2-1 SSW001-1

Work after disconnecting

the cables CL1 3-0

CL1 0-1 SSW000-1

Cap

Cable

CL1 1-0

Fig. 3.11.3-4 Disconnection of Cables (FBX_CC1_CL1)

INST03-11B-110
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-120

When you need to remove Device Interface Cable CC1 (DKC-F810I-CC1) from
DKU-10(UBX/SBX)
(2)-1 Disconnect the cables from the SSWs in the DKU-10. (Refer to Fig. 3.11.3-5 and Fig.
3.11.3-6.)
(2)-2 Attach the caps to the disconnected cables.

CAUTION
A serious failure occurs if a wrong cable or connector is removed.
Since a label bearing a connection destination is affixed on each cable or connector to be
removed, work very carefully referring to it and the wiring diagram.

SSW103-1

CL1 3-0

SSW102-1

CL1 2-1

SSW101-1
Rear View of
DKU-10(UBX/SBX)

SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 CL1 1-0
Front View of SSW

Work after disconnecting SSW100-1

the cables

Cap
CL1 0-1
Cable

Fig. 3.11.3-5 Disconnection of Cables (UBX/SBX_CC1_CL1_L)

INST03-11B-120
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-130

CAUTION
A serious failure occurs if a wrong cable or connector is removed.
Since a label bearing a connection destination is affixed on each cable or connector to be
removed, work very carefully referring to it and the wiring diagram.

SSW107-1

CL1 7-0

SSW106-1

CL1 6-1

Rear View of SSW105-1

DKU-10(UBX/SBX)

SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 CL1 5-0
Front View of SSW

SSW104-1
Work after disconnecting
the cables

Cap
CL1 4-1

Cable

Fig. 3.11.3-6 Disconnection of Cables (UBX/SBX_CC1_CL1_U)

INST03-11B-130
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-140

When you need to remove Device Interface Cable CC1 (DKC-F810I-CC1) from DKU-10(FBX)
(2)-1 Disconnect the cables from the SSWs in the DKU-10.
(2)-2 Attach the caps to the disconnected cables.

CAUTION
A serious failure occurs if a wrong cable or connector is removed.
Since a label bearing a connection destination is affixed on each cable or connector to be
removed, work very carefully referring to it and the wiring diagram.

CL1 6-1 SSW103-1

CL1 7-0

Rear View of DKU-10(FBX) CL1 4-1 SSW102-1

SSWxyz-1 SSWxyz-2
CL1 5-0
-0 -1 -2 -0 -1 -2 -0 -1 -2 -0 -1 -2
Front View of SSW CL1 2-1 SSW101-1

Work after disconnecting

the cables

CL1 3-0
Cap
CL1 0-1 SSW100-1
Cable

CL1 1-0

Fig. 3.11.3-7 Disconnection of Cables (FBX_CC1_CL1)

INST03-11B-140
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-150

(2)-3 Open the loop cable ties and remove the DKC-F810I-CC1 (four cables). (Refer to Fig.
3.11.3-8 or Fig. 3.11.3-9.)

When the DKU-x0 is the UBX/SBX.

DKU-x0(UBX/SBX)

Loop Cable Tie

Cable (CC1)

DKC-x

Rear View of
RACK-x0

Fig. 3.11.3-8 Removal of Cables (UBX/SBX_CC1_CL1)

INST03-11B-150
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-160

When the DKU-x0 is the FBX.

DKU-x0 (FBX)

Loop Cable Tie Cable (CC1)

DKC-x

Rear View of
RACK-x0

Fig. 3.11.3-9 Removal of Cables (FBX_CC1_CL1)

INST03-11B-160
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-170

(3) <Check SAS cable connection>

When a message, “Disconnect the SAS cables
from the SSW (OUT0) connected with DKA
(DKA-nnn) of cluster-1, connect the SAS
cables to the installation target DKA
(DKA-nnn), and then select [OK].” is
displayed, select (CL) the [OK] button.

(4) <Check that hardware components are installed>

At this point refrain from pressing the [OK]
button.
“Insert the DKA-nnn, and then select [OK].” is
displayed.

INST03-11B-170
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-180

4. Installation Procedure of Disk Adapter for cluster 1

NOTICE: Be sure to wear your wrist strap and attach to ground prior to performing the
following work. This will ensure that the IC and LSI on the PCB are protected
from static electricity.

4-1 Insertion of PCBs

a. If the dummy plates are installed in the installation location, loosen the screws and remove
the dummy plates. Refer to the Table 3.11.3-5 and Fig. 3.11.3-10.
If not, go to Step b.
NOTE: Store the removed dummy plates as they are required when the DKAs are removed.

NOTICE: Remove the dummy plate just before installing the PCB.
If the dummy plate is kept removed for a long time, the wind doesn’t flow among
installed PCBs, causing the PCBs’ temperature rise which may result in
temperature warning or temperature alarm.
b. Insert the PCBs to the correct locations in the DKC and fasten the screw.

Main Edge Connector

PCB NOTICE: • Check that the main edge connector of the PCB has
no deformation, damage or sticking of dust before
installing the PCB. (See INST03-01-80)
• When installing the PCB, hold the right and left of the
PCB with both hands, and insert it straight not to
contact the neighboring PCB.

Table 3.11.3-5 Inserting Location

DKC Addition No. Location No. Number of DKAs set Remarks
Cluster 1 through the SVP
DKC-0 Basic DKA-1PA 2 4
Option 1 DKA-1PB —
DKC-1 Option 2 DKA-1PG 2 4
Option 3 DKA-1PH —

INST03-11B-180
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-190

1 1 2 2 1 1 2 2
P P P P P P P P
A B B A G H HG

Rear View of DKC-0 Rear View of DKC-1

DKC

DKA PCB

Lever Screw

Screw

Dummy Plate

Lever Screw
Screw
Fig. 3.11.3-10 Insertion of PCB

INST03-11B-190
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-200

5. Attachment Procedure of Device Interface Cable for Cluster 1 (DKC-F810I-CC2)

5-1 Connection of Cables

In the case of cable installation between DKA-1PA and DKU-00

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.
a. Remove the caps from the DEV interface cables.
b. Connect the cables to the DKA PCBs in the DKC-0 after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180).

DKA PCB
(DKA-1PA)

CL1 1PA-0

CL1 1PA-1

Work before connecting the cables.

CL1 1PA-2

CL1 1PA-3

Cap

Cable

Fig. 3.11.3-11 Connection of Cables

INST03-11B-200
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-210

c. Remove the caps from the cables to be connected.

d. Connect the four cables to the SSWs in the DKU after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180). (Refer to Fig. 3.11.3-12 or Fig.
3.11.3-13.)

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-00 is the UBX/SBX.

SSW006-1

CL1 6-0

SSW004-1

CL1 4-0

Rear View of SSW002-1

DKU-00(UBX/SBX)

SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 CL1 2-0
Front View of SSW

Work before connecting SSW000-1

the cables.

Cap CL1 0-0

Cable

Fig. 3.11.3-12 Connection of Cables (CC2_DKU-00(UBX/SBX)_CL1)

INST03-11B-210
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-220

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-00 is the FBX.

CL1 6-0
SSW003-1

Rear View of DKU-00(FBX) CL1 4-0

SSW002-1

SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 -0 -1 -2 -0 -1 -2
Front View of SSW CL1 2-0
SSW001-1

Work before connecting

the cables

Cap
CL1 0-0
SSW000-1
Cable

Fig. 3.11.3-13 Connection of Cables (CC2_DKU-00(FBX)_CL1)

INST03-11B-220
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-230

In the case of cable installation between DKA-1PB and DKU-00

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.
a. Remove the caps from the DEV interface cables.
b. Connect the cables to the DKA PCBs in the DKC-0 after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180).

DKA PCB
(DKA-1PB)

CL1 1PB-0

CL1 1PB-1

Work before connecting the cables.

CL1 1PB-2

CL1 1PB-3

Cap

Cable

Fig. 3.11.3-14 Connection of Cables

INST03-11B-230
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-240

c. Remove the caps from the cables to be connected.

d. Connect the four cables to the SSWs in the DKU after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180). (Refer to Fig. 3.11.3-15 or Fig.
3.11.3-16.)

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-00 is the UBX/SBX.

SSW007-1

CL1 7-0

SSW005-1

CL1 5-0

Rear View of SSW003-1

DKU-00(UBX/SBX)

SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 CL1 3-0
Front View of SSW

Work before connecting SSW001-1

the cables

Cap CL1 1-0

Cable

Fig. 3.11.3-15 Connection of Cables (CC2_DKU-00(UBX/SBX)_CL1)

INST03-11B-240
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-250

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-00 is the FBX.

SSW003-1

CL1 7-0

Rear View of DKU-00(FBX) SSW002-1

SSWxyz-1 SSWxyz-2
CL1 5-0
-0 -1 -2 -0 -1 -2 -0 -1 -2 -0 -1 -2
Front View of SSW
SSW001-1

Work before connecting

the cables
CL1 3-0

SSW000-1
Cap

Cable

CL1 1-0

Fig. 3.11.3-16 Connection of Cables (CC2_DKU-00(FBX)_CL1)

INST03-11B-250
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-260

In the case of cable installation between DKA-1PG and DKU-10

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.
a. Remove the caps from the DEV interface cables.
b. Connect the cables to the DKA PCBs in the DKC-1 after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180).

DKA PCB
(DKA-1PG)

CL1 1PG-0

CL1 1PG-1

Work before connecting the cables.

CL1 1PG-2

CL1 1PG-3

Cap

Cable

Fig. 3.11.3-17 Connection of Cables

INST03-11B-260
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-270

c. Remove the caps from the cables to be connected.

d. Connect the four cables to the SSWs in the DKU after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180). (Refer to Fig. 3.11.3-18 or Fig.
3.11.3-19.)

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-10 is the UBX/SBX.

SSW106-1

CL1 6-0

SSW104-1

CL1 4-0

Rear View of SSW102-1

DKU-10(UBX/SBX)

SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 CL1 2-0
Front View of SSW

Work before connecting SSW100-1

the cables

Cap CL1 0-0

Cable

Fig. 3.11.3-18 Connection of Cables (CC2_DKU-10(UBX/SBX)_CL1)

INST03-11B-270
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-280

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-10 is the FBX.

CL1 6-0
SSW103-1

Rear View of DKU-10(FBX) CL1 4-0

SSW102-1

SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 -0 -1 -2 -0 -1 -2
Front View of SSW CL1 2-0
SSW101-1

Work before connecting

the cables

Cap
CL1 0-0
SSW100-1
Cable

Fig. 3.11.3-19 Connection of Cables (CC2_DKU-10(FBX)_CL1)

INST03-11B-280
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-290

In the case of cable installation between DKA-1PH and DKU-10

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.
a. Remove the caps from the DEV interface cables.
b. Connect the cables to the DKA PCBs in the DKC-1 after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180).

DKA PCB
(DKA-1PH)

CL1 1PH-0

CL1 1PH-1

Work before connecting the cables.

CL1 1PH-2

CL1 1PH-3

Cap

Cable

Fig. 3.11.3-20 Connection of Cables

INST03-11B-290
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-300

c. Remove the caps from the cables to be connected.

d. Connect the four cables to the SSWs in the DKU after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180). (Refer to Fig. 3.11.3-21 or Fig.
3.11.3-22.)

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-10 is the UBX/SBX.

SSW107-1

CL1 7-0

SSW105-1

CL1 5-0

Rear View of SSW103-1

DKU-10(UBX/SBX)

SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 CL1 3-0
Front View of SSW

Work before connecting SSW101-1

the cables

Cap CL1 1-0

Cable

Fig. 3.11.3-21 Connection of Cables (CC2_DKU-10(UBX/SBX)_CL1)

INST03-11B-300
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-310

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-10 is the FBX.

SSW103-1

CL1 7-0

Rear View of DKU-10(FBX) SSW102-1

SSWxyz-1 SSWxyz-2
CL1 5-0
-0 -1 -2 -0 -1 -2 -0 -1 -2 -0 -1 -2
Front View of SSW
SSW101-1

Work before connecting

the cables
CL1 3-0

SSW000-1
Cap

Cable

CL1 1-0

Fig. 3.11.3-22 Connection of Cables (CC2_DKU-10(FBX)_CL1)

INST03-11B-310
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-320

5-2 Attachment of Cables

In the case of cable installation between DKA-1PA and DKU-00 or between DKA-1PG and DKU-10
a. Route the four cables in the cluster 1 and fix them with the loop cable ties. (Refer to Fig.
3.11.3-23 or Fig. 3.11.3-24.)

When the DKU-x0 is the UBX/SBX.

DKU-x0(UBX/SBX)

Loop Cable Tie

Cable

DKC-x

Loop Cable Tie

Cable Duct

Rear View of
RACK-x0

Fig. 3.11.3-23 Fixation of Cables (DKA-1PA – DKU-00(UBX/SBX) or DKA-1PG –

DKU-10(UBX/SBX))

INST03-11B-320
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-330

When the DKU-x0 is the FBX.

DKU-x0 (FBX)
Loop Cable Tie

Cable

DKC-x

Loop Cable Tie

Cable Duct

Rear View of
RACK-x0

Fig. 3.11.3-24 Fixation of Cables (DKA-1PA – DKU-00(FBX) or DKA-1PG –

DKU-10(FBX))

INST03-11B-330
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-340

In the case of cable installation between DKA-1PB and DKU-00 or between DKA-1PH and DKU-10
a. Route the four cables in the cluster 1 and fix them with the loop cable ties. (Refer to Fig.
3.11.3-25 or Fig. 3.11.3-26.)

When the DKU-x0 is the UBX/SBX.

DKU-x0(UBX/SBX)

Loop Cable Tie

Cable (*1)
DKA DKC-x

Loop Cable Tie

Cable Duct

Rear View of
RACK-x0
*1: Pass the cables connected to the DKA-1PB or DKA-1PH into the
loop cable ties form upper side so that the DKA on the end side
can be inserted or extracted

Fig. 3.11.3-25 Fixation of Cables (DKA-1PB – DKU-00(UBX/SBX) or DKA-1PH –

DKU-10(UBX/SBX))

INST03-11B-340
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-350

When the DKU-x0 is the FBX.

DKU-x0 (FBX)
Loop Cable Tie

Cable
(*1)
DKC-x
DKA

Loop Cable Tie

Cable Duct

Rear View of
RACK-x0

*1: Pass the cables connected to the DKA-1PB or DKA-1PH into the
loop cable ties form upper side so that the DKA on the end side
can be inserted or extracted

Fig. 3.11.3-26 Fixation of Cables (DKA-1PB – DKU-00(FBX) or DKA-1PH –

DKU-10(FBX))

INST03-11B-350
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-360

6. SVP Post-Procedure (Cluster 1)

(1) <Check that hardware components are installed>
Select (CL) [OK] after making sure that all
hardware components are installed correctly in
response to “Insert the DKA-nnn, and then
select [OK].”.

(2)
“Waiting for Power Event... Usually, several minutes (maximum 15 minutes)” is displayed.

If [ONL3437E] or [ONL3438E] is displayed, please refer 2.10.1. (INST02-420)

(3) <DKU PATH INLINE>

When DKA is installed, “DKU PATH INLINE is now running...” is displayed.

INST03-11B-360
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-370

7. SVP Post-Procedure (Cluster 2)

(1) <Check SAS cable connection>
“Disconnect the SAS cables from the SSW
(OUT0) connected with DKA (DKA-nnn) of
cluster-2, connect the SAS cables to the
installation target DKA (DKA-nnn), and then
select [OK].”is displayed.

NOTE: This message is displayed when

changing from the Standard Model to the High Performance Model.

NOTE: Connect the cables of Blinking LED.

SSW (UBX / SBX)

SSWx07-2
SSWx05-2
SSWx03-2
SSWx01-2

SSWx06-2
SSWx04-2
SSWx02-2
SSWx00-2

SSW (FBX)

SSWx03-2
SSWx02-2
SSWx01-2
SSWx00-2

INST03-11B-370
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-380

(2) <Connect SAS cable>

When you need to remove Device Interface Cable CC1 (DKC-F810I-CC1) from
DKU-00(UBX/SBX)
(2)-1 Disconnect the cables from the SSWs in the DKU-00. (Refer to Fig. 3.11.3-27 and Fig.
3.11.3-28.)
(2)-2 Attach the caps to the disconnected cables.

CAUTION
A serious failure occurs if a wrong cable or connector is removed.
Since a label bearing a connection destination is affixed on each cable or connector to be
removed, work very carefully referring to it and the wiring diagram.

SSW003-2

CL2 3-1

SSW002-2

Rear View of CL2 2-0

DKU-00(UBX/SBX)

SSWxyz-1 SSWxyz-2 SSW001-2

-0 -1 -2 -0 -1 -2
Front View of SSW

Work after disconnecting CL2 1-1

the cables

SSW000-2

Cap

Cable
CL2 0-0
Fig. 3.11.3-27 Disconnection of Cables (UBX/SBX_CC1_CL2_L)

INST03-11B-380
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-390

CAUTION
A serious failure occurs if a wrong cable or connector is removed.
Since a label bearing a connection destination is affixed on each cable or connector to be
removed, work very carefully referring to it and the wiring diagram.

SSW007-2

CL2 7-1

SSW006-2

Rear View of CL2 6-0

DKU-00(UBX/SBX)

SSW005-2
SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2
Front View of SSW

Work after disconnecting CL2 5-1

the cables

SSW004-2

Cap

Cable
CL2 4-0

Fig. 3.11.3-28 Disconnection of Cables (UBX/SBX_CC1_CL2_U)

INST03-11B-390
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-400

When you need to remove Device Interface Cable CC1 (DKC-F810I-CC1) from DKU-00(FBX)
(2)-1 Disconnect the cables from the SSWs in the DKU-00.
(2)-2 Attach the caps to the disconnected cables.

CAUTION
A serious failure occurs if a wrong cable or connector is removed.
Since a label bearing a connection destination is affixed on each cable or connector to be
removed, work very carefully referring to it and the wiring diagram.

CL2 6-0 SSW003-2

Rear View of DKU-00(FBX)

CL2 7-1

CL2 4-0 SSW002-2

SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 -0 -1 -2 -0 -1 -2
Front View of SSW
CL2 5-1

Work after disconnecting CL2 2-0 SSW001-2

the cables

Cap
CL2 3-1

Cable
CL2 0-0 SSW000-2

CL2 1-1
Fig. 3.11.3-29 Disconnection of Cables (FBX_CC1_CL2)

INST03-11B-400
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-410

When you need to remove Device Interface Cable CC1 (DKC-F810I-CC1) from
DKU-10(UBX/SBX)
(2)-1 Disconnect the cables from the SSWs in the DKU-10. (Refer to Fig. 3.11.3-30 and Fig.
3.11.3-31.)
(2)-2 Attach the caps to the disconnected cables.

CAUTION
A serious failure occurs if a wrong cable or connector is removed.
Since a label bearing a connection destination is affixed on each cable or connector to be
removed, work very carefully referring to it and the wiring diagram.

SSW103-2

CL2 3-1

SSW102-2

Rear View of CL2 2-0

DKU-10(UBX/SBX)

SSWxyz-1 SSWxyz-2 SSW101-2

-0 -1 -2 -0 -1 -2
Front View of SSW

Work after disconnecting

the cables CL2 1-1

SSW100-2
Cap

Cable

CL2 0-0
Fig. 3.11.3-30 Disconnection of Cables (UBX/SBX_CC1_CL2_L)

INST03-11B-410
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-420

CAUTION
A serious failure occurs if a wrong cable or connector is removed.
Since a label bearing a connection destination is affixed on each cable or connector to be
removed, work very carefully referring to it and the wiring diagram.

SSW107-2

CL2 7-1

SSW106-2

Rear View of CL2 6-0

DKU-10(UBX/SBX)
SSW105-2
SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2
Front View of SSW

CL2 5-1
Work after disconnecting
the cables
SSW104-2

Cap

Cable
CL2 4-0

Fig. 3.11.3-31 Disconnection of Cables (UBX/SBX_CC1_CL2_U)

INST03-11B-420
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-430

When you need to remove Device Interface Cable CC1 (DKC-F810I-CC1) from DKU-10(FBX)
(2)-1 Disconnect the cables from the SSWs in the DKU-10.
(2)-2 Attach the caps to the disconnected cables.

CAUTION
A serious failure occurs if a wrong cable or connector is removed.
Since a label bearing a connection destination is affixed on each cable or connector to be
removed, work very carefully referring to it and the wiring diagram.

CL2 6-0 SSW103-2

Rear View of DKU-10(FBX)

CL2 7-1

CL2 4-0 SSW102-2

SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 -0 -1 -2 -0 -1 -2
Front View of SSW
CL2 5-1

Work after disconnecting CL2 2-0 SSW101-2

the cables

Cap
CL2 3-1

Cable
CL2 0-0 SSW100-2

CL2 1-1
Fig. 3.11.3-32 Disconnection of Cables (FBX_CC1_CL2)

INST03-11B-430
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-440

(2)-3 Open the loop cable ties and remove the DKC-F810I-CC1 (four cables). (Refer to Fig.
3.11.3-33 or Fig. 3.11.3-34.)

When the DKU-x0 is the UBX/SBX.

DKU-x0
(UBX/SBX)

Cable Loop Cable Tie

(CC1)

DKC-x

Rear View of
RACK-x0

Fig. 3.11.3-33 Removal of Cables (UBX/SBX_CC1_CL2)

INST03-11B-440
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-450

When the DKU-x0 is the FBX.

DKU-x0
(FBX)

Cable
(CC1) Loop Cable Tie

DKC-x

Rear View of
RACK-x0

Fig. 3.11.3-34 Removal of Cables (FBX_CC1_CL2)

INST03-11B-450
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-460

(3) <Check SAS cable connection>

When a message, “Disconnect the SAS cables
from the SSW (OUT0) connected with DKA
(DKA-nnn) of cluster-2, connect the SAS
cables to the installation target DKA
(DKA-nnn), and then select [OK].” is
displayed, select (CL) the [OK] button.

(4) <Blockage of DKA on Cluster 2>

A message showing the status of recovery processing on Cluster 1 is displayed.
After completing the recovery processing on Cluster 1, blockage of DKA on Cluster 2 is
performed and a message showing the processing status is displayed.

(5) <Check that hardware components are installed>

At this point refrain from pressing the [OK]
button.
“Insert the DKA-nnn, and then select [OK].” is
displayed.

INST03-11B-460
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-470

8. Installation Procedure of Disk Adapter for cluster 2

NOTICE: Be sure to wear your wrist strap and attach to ground prior to performing the
following work. This will ensure that the IC and LSI on the PCB are protected
from static electricity.

8-1 Insertion of PCBs

a. If the dummy plates are installed in the installation location, loosen the screws and remove
the dummy plates. Refer to the Table 3.11.3-6 and Fig. 3.11.3-35.
If not, go to Step b.
NOTE: Store the removed dummy plates as they are required when the DKAs are removed.

NOTICE: Remove the dummy plate just before installing the PCB.
If the dummy plate is kept removed for a long time, the wind doesn’t flow among
installed PCBs, causing the PCBs’ temperature rise which may result in
temperature warning or temperature alarm.

INST03-11B-470
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-480

b. Insert the PCBs to the correct locations in the DKC and fasten the screw.

Main Edge Connector

PCB NOTICE: • Check that the main edge connector of the PCB has
no deformation, damage or sticking of dust before
installing the PCB. (See INST03-01-80)
• When installing the PCB, hold the right and left of the
PCB with both hands, and insert it straight not to
contact the neighboring PCB.

Table 3.11.3-6 Inserting Location

DKC Addition No. Location No. Number of DKAs set Remarks
Cluster 2 through the SVP
DKC-0 Basic DKA-2PA 2 4
Option 1 DKA-2PB —
DKC-1 Option 2 DKA-2PG 2 4
Option 3 DKA-2PH —

INST03-11B-480
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-490

1 1 2 2 1 1 2 2
P P P P P P P P
A B B A G H HG

Rear View of DKC-0 Rear View of DKC-1

DKC

DKA PCB

Lever Screw

Screw

Dummy Plate

Lever Screw
Screw
Fig. 3.11.3-35 Insertion of PCB

INST03-11B-490
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-500

9. Attachment Procedure of Device Interface Cable for Cluster 2 (DKC-F810I-CC2)

9-1 Connection of cables

In the case of cable installation between DKA-2PA and DKU-00

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.
a. Remove the caps from the DEV interface cables.
b. Connect the cables to the DKA PCBs in the DKC-0 after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180).

DKA PCB
(DKA-2PA)

CL2 2PA-0

CL2 2PA-1

Work before connecting the cables.

CL2 2PA-2

CL2 2PA-3

Cap

Cable

Fig. 3.11.3-36 Connection of Cables

INST03-11B-500
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-510

c. Remove the caps from the cables to be connected.

d. Connect the four cables to the SSWs in the DKU after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180). (Refer to Fig. 3.11.3-37 or Fig.
3.11.3-38.)

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-00 is the UBX/SBX.

SSW007-2

CL2 7-0

SSW005-2

Rear View of CL2 5-0

DKU-00 (UBX/SBX)

SSWxyz-1 SSWxyz-2 SSW003-2

-0 -1 -2 -0 -1 -2
Front View of SSW

Work before connecting CL2 3-0

the cables.

SSW001-2

Cap

Cable
CL2 1-0

Fig. 3.11.3-37 Connection of Cables (CC2_DKU-00 (UBX/SBX)_CL2)

INST03-11B-510
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-520

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-00 is the FBX.

SSW003-2

Rear View of DKU-00 (FBX)

CL2 7-0

SSW002-2
SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 -0 -1 -2 -0 -1 -2
Front View of SSW
CL2 5-0

SSW001-2

Work before connecting

the cables.
CL2 3-0

Cap SSW000-2

Cable

CL2 1-0
Fig. 3.11.3-38 Connection of Cables (CC2_DKU-00 (FBX)_CL2)

INST03-11B-520
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-530

In the case of cable installation between DKA-2PB and DKU-00

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.
a. Remove the caps from the DEV interface cables.
b. Connect the cables to the DKA PCBs in the DKC-0 after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180).

DKA PCB
(DKA-2PB)

CL2 2PB-0

CL2 2PB-1

Work before connecting the cables.

CL2 2PB-2

CL2 2PB-3

Cap

Cable

Fig. 3.11.3-39 Connection of Cables

INST03-11B-530
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-540

c. Remove the caps from the cables to be connected.

d. Connect the four cables to the SSWs in the DKU after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180). (Refer to Fig. 3.11.3-40 or Fig.
3.11.3-41.)

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-00 is the UBX/SBX.

SSW006-2

CL2 6-0

SSW004-2

Rear View of CL2 4-0

DKU-00 (UBX/SBX)

SSWxyz-1 SSWxyz-2 SSW002-2

-0 -1 -2 -0 -1 -2

Front View of SSW

Work before connecting CL2 2-0

the cables.

SSW000-2

Cap

Cable
CL2 0-0

Fig. 3.11.3-40 Connection of Cables (CC2_DKU-00 (UBX/SBX)_CL2)

INST03-11B-540
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-550

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-00 is the FBX.

CL2 6-0 SSW003-2

Rear View of DKU-00 (FBX)

CL2 4-0 SSW002-2

SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 -0 -1 -2 -0 -1 -2
Front View of SSW

CL2 2-0 SSW001-2

Work before connecting
the cables.

Cap

Cable CL2 0-0 SSW000-2

Fig. 3.11.3-41 Connection of Cables (CC2_DKU-00 (FBX)_CL2)

INST03-11B-550
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-560

In the case of cable installation between DKA-2PG and DKU-10

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.
a. Remove the caps from the DEV interface cables.
b. Connect the cables to the DKA PCBs in the DKC-1 after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180).

DKA PCB
(DKA-2PG)

CL2 2PG-0

CL2 2PG-1

Work before connecting the cables.

CL2 2PG-2

CL2 2PG-3

Cap

Cable

Fig. 3.11.3-42 Connection of Cables

INST03-11B-560
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-570

c. Remove the caps from the cables to be connected.

d. Connect the four cables to the SSWs in the DKU after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180). (Refer to Fig. 3.11.3-43 or Fig.
3.11.3-44.)

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-10 is the UBX/SBX.

SSW107-2

CL2 7-0

SSW105-2

Rear View of CL2 5-0

DKU-10 (UBX/SBX)

SSWxyz-1 SSWxyz-2 SSW103-2

-0 -1 -2 -0 -1 -2
Front View of SSW

Work before connecting CL2 3-0

the cables.

SSW101-2

Cap

Cable
CL2 1-0

Fig. 3.11.3-43 Connection of Cables (CC2_DKU-10 (UBX/SBX)_CL2)

INST03-11B-570
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-580

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-10 is FBX.

SSW103-2

Rear View of DKU-10 (FBX)

CL2 7-0

SSW102-2
SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 -0 -1 -2 -0 -1 -2
Front View of SSW
CL2 5-0

SSW101-2

Work before connecting

the cables.
CL2 3-0

Cap SSW100-2

Cable

CL2 1-0
Fig. 3.11.3-44 Connection of Cables (CC2_DKU-10 (FBX)_CL2)

INST03-11B-580
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-590

In the case of cable installation between DKA-2PH and DKU-10

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.
a. Remove the caps from the DEV interface cables.
b. Connect the cables to the DKA PCBs in the DKC-1 after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180).

DKA PCB
(DKA-2PH)

CL2 2PH-0

CL2 2PH-1

Work before connecting the cables.

CL2 2PH-2

CL2 2PH-3

Cap

Cable

Fig. 3.11.3-45 Connection of Cables

INST03-11B-590
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-600

c. Remove the caps from the cables to be connected.

d. Connect the four cables to the SSWs in the DKU after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180). (Refer to Fig. 3.11.3-46 or Fig.
3.11.3-47.)

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-10 is the UBX/SBX.

SSW106-2

CL2 6-0

SSW104-2

Rear View of CL2 4-0

DKU-10 (UBX/SBX)

SSWxyz-1 SSWxyz-2 SSW102-2

-0 -1 -2 -0 -1 -2
Front View of SSW

Work before connecting CL2 2-0

the cables.

SSW100-2

Cap

Cable
CL2 0-0

Fig. 3.11.3-46 Connection of Cables (CC2_DKU-10 (UBX/SBX)_CL2)

INST03-11B-600
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-610

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-10 is the FBX.

CL2 6-0 SSW103-2

Rear View of DKU-10 (FBX)

CL2 4-0 SSW102-2

SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 -0 -1 -2 -0 -1 -2
Front View of SSW

CL2 2-0 SSW101-2

Work before connecting
the cables.

Cap

Cable CL2 0-0 SSW100-2

Fig. 3.11.3-47 Connection of Cables (CC2_DKU-10 (FBX)_CL2)

INST03-11B-610
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-620

9-2 Attachment of Cables

In the case of cable installation between DKA-2PA and DKU-00 or between DKA-2PG and DKU-10
a. Route the four cables in the cluster 2 and fix them with the loop cable ties. (Refer to Fig.
3.11.3-48 or Fig. 3.11.3-49.)

When the DKU-x0 is the UBX/SBX.

DKU-x0
(UBX/SBX)

Loop Cable Tie

Cable
DKC-x

Loop Cable Tie

Cable Duct

Rear View of
RACK-x0

Fig. 3.11.3-48 Fixation of Cables (DKA-2PA – DKU-00 (UBX/SBX) or

DKA-2PG – DKU-10 (UBX/SBX))

INST03-11B-620
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-630

When the DKU-x0 is the FBX.

DKU-x0
(FBX)

Loop Cable Tie

Cable
DKC-x

Loop Cable Tie

Cable Duct

Rear View of
RACK-x0

Fig. 3.11.3-49 Fixation of Cables

(DKA-2PA – DKU-00 (FBX) or DKA-2PG – DKU-10 (FBX))

INST03-11B-630
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-640

In the case of cable installation between DKA-2PB and DKU-00 or between DKA-2PH and DKU-10
a. Route the four cables in the cluster 2 and fix them with the loop cable ties. (Refer to Fig.
3.11.3-50 or Fig. 3.11.3-51.)

When the DKU-x0 is the UBX/SBX

DKU-x0
(UBX/SBX)

Loop Cable Tie

(*1) Cable
DKC-x
DKA

Loop Cable Tie

Cable Duct

Rear View of
RACK-x0
*1: Pass the cables connected to the DKA-2PB or DKA-2PH into the
loop cable ties form upper side so that the DKA on the end side can
be inserted or extracted.

Fig. 3.11.3-50 Fixation of Cables

(DKA-2PB – DKU-00 (UBX/SBX) or DKA-2PH – DKU-10 (UBX/SBX))
INST03-11B-640
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-650

When the DKU-x0 is the FBX

DKU-x0
(FBX)

Loop Cable Tie

Cable
DKC-x (*1)
DKA

Loop Cable Tie

Cable Duct

Rear View of
RACK-x0

*1: Pass the cables connected to the DKA-2PB or DKA-2PH into the
loop cable ties form upper side so that the DKA on the end side can
be inserted or extracted.

Fig. 3.11.3-51 Fixation of Cables

(DKA-2PB – DKU-00 (FBX) or DKA-2PH – DKU-10 (FBX))

INST03-11B-650
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-660

10. SVP Post-Procedure (Cluster 2)

(1) <Check that hardware components are installed>
Select (CL) [OK] after making sure that all
hardware components are installed correctly in
response to “Insert the DKA-nnn, and then
select [OK].”.

(2)
“Waiting for Power Event... Usually, several minutes (maximum 15 minutes)” is displayed.

If [ONL3437E] or [ONL3438E] is displayed, please refer 2.10.1. (INST02-420)

(3) <DKU PATH INLINE>

When DKA is installed, “DKU PATH INLINE is now running...” is displayed.

(4) <End of system update processing>

“Renewal process has completed. Please check
storage system status.” is displayed when
recovery processing on all installed
components is completed. Select (CL) [OK] in
response to this message.

INST03-11B-660
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11B-670

(5)
Execute an operation for backing up the
configuration information.
Prepare the removable media for backup and
insert the media.
Please select (CL) the [Refresh] button, and
update drive information.
Select (CL) the drive and the PC in which the
media was inserted. Select (CL) the [OK]
button.
NOTE: For the procedure of backing up the
configuration information to a CD-R,
see page MICRO07-190.

(6)
When this procedure is completed, the message
“Please remove the Config media.” is displayed.
Remove the configuration information media,
select (CL) [OK].

(7)
After the procedure is completed, return to
‘Install’.
Select (CL) [File]-[Exit].

(8) <Mode Change>

Change the mode to View Mode.

Return to the work table (INST02-50) and perform rest of the works.

INST03-11B-670
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-10

3.11.4 When performing addition of the data/spare Drive and Device Interface Cable that
accompanies the addition of the DKU
(DKC-F810I-CC1/CC2/CC4/300KCM/600JCM/900JCM/1R2JCM/3R0H3M/4R0H3M/
400MCM/800MCM/1R6FM/3R2FM)

NOTE: • When the second DKC-F810I-SCA is installed, the Device Interface Cables between
DKA and DKU, and between DKU and DKU are required to be connected.
• For the Non-Disruptive Installation, execute the operation after turning on the power
supply of the RACK as shown in the Step No.7 of 2.2 Non-Disruptive Installation
Procedure Table (INST02-50).

INST03-11C-10
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-20

3.11.4.1 Storage system Configurations and Required I/F Cable Options

1. In the case of Standard Model
The storage system configuration and number of required options for the Standard Model are
shown below.

Table 3.11.4.1-1 Requisite Options for Standard Model (Single and Twin DKC model)
No. Required Number of Options
DKC810I DKC-F810I- 2.5-inch 3.5-inch FMD
-CBXA CBXB RK42 SBX UBX FBX SCA CC1 CC2 CC4 MOD5 HDD HDD (*1)
(*1) (*1)
1 1 — 1 1 — 1 1 1 — — 192 — —
2 1 — 1 2 — 1 1 3 — — 384 — —
3 1 — 2 3 — 1 1 3 2 — 576 — —
4 1 — 2 4 — 1 1 5 2 — 768 — —
5 1 — 3 5 — 1 1 5 4 — 960 — —
6 1 — 3 6 — 1 1 7 4 — 1152 — —
7 1 1 4 7 — 2 2 8 4 1 1344 — —
8 1 1 4 8 — 2 2 10 4 1 1536 — —
9 1 1 5 9 — 2 2 10 6 1 1728 — —
10 1 1 5 10 — 2 2 12 6 1 1920 — —
11 1 1 6 11 — 2 2 12 8 1 2112 — —
12 1 1 6 12 — 2 2 14 8 1 2304 — —
13 1 — 1 — 1 1 1 1 — — — 96 —
14 1 — 1 — 2 1 1 3 — — — 192 —
15 1 — 2 — 3 1 1 3 2 — — 288 —
16 1 — 2 — 4 1 1 5 2 — — 384 —
17 1 — 3 — 5 1 1 5 4 — — 480 —
18 1 — 3 — 6 1 1 7 4 — — 576 —
19 1 1 4 — 7 2 2 8 4 1 — 672 —
20 1 1 4 — 8 2 2 10 4 1 — 768 —
21 1 1 5 — 9 2 2 10 6 1 — 864 —
22 1 1 5 — 10 2 2 12 6 1 — 960 —
23 1 1 6 — 11 2 2 12 8 1 — 1056 —
24 1 1 6 — 12 2 2 14 8 1 — 1152 —
25 1 — 1 — — 1 1 1 1 — — — — 48
26 1 — 1 — — 2 1 3 1 — — — — 96
27 1 1 2 — — 3 2 4 2 — 1 — — 144
28 1 1 2 — — 4 2 6 2 — 1 — — 192

*1: The maximum number of installable HDDs/FMDs includes the spare disk(s).

INST03-11C-20
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-30

Table 3.11.4.1-2 Requisite Options for Standard Model (Dual DKC model)
Required Number of Options
No. DKC810I DKC-F810I- FMD Remarks
-CBXA CBXB RK42 FBX SCA CC1 CC2 CC4 FC5 MOD5 (*1)
1 1 1 1 2 2 2 2 — — 1 96 Dual DKC Layout-1
2 1 1 2 3 2 2 2 — 2 1 144 Dual DKC Layout-1
3 1 1 3 4 2 2 2 2 2 1 192 Dual DKC Layout-1
4 1 1 1 2 2 2 — — 2 1 96 Dual DKC Layout-2
5 1 1 2 3 2 2 — — 4 1 144 Dual DKC Layout-2
6 1 1 3 4 2 2 — 2 4 1 192 Dual DKC Layout-2
7 1 1 2 2 2 2 — — 2 1 96 Dual DKC Layout-3
8 1 1 2 3 2 4 — — 2 1 144 Dual DKC Layout-3
9 1 1 2 4 2 6 — — 2 1 192 Dual DKC Layout-3

*1: The maximum number of installable FMDs includes the spare drive(s).

INST03-11C-30
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-40

RACK-00 RACK-01 RACK-02

DKC-F810I DKU-01 DKC-F810I-

-SBX DKC-F810I-
CC4/FC5/FC30/FC1J
CC4/FC5/FC30/FC1J
HDU
DKC-F810I DKC-F810I-
-CC2 CC4/FC5/FC30/FC1J
DKC-F810I
-CC2 DKU-00
DKU-03 DKU-05
DKC-F810I
-SBX HDU
HDU HDU
DKC-F810I
-CC1 (inner DKC-F810I
connection) -CC2
DKC-F810I DKA 0
-CC2 DKU-02 DKU-04 DKC-F810I
DKC-0 -CC2
DKC-F810I
-SCA CPEX CPEX HDU HDU
0 1
DKC810I
-CBXA
DKC-F810I-MFC5/ DKC-F810I-CPEX DKC-F810I-CC4/FC5/FC30/FC1J
MFC30/MFC1J
DKC-F810I-MOD5/
MOD30/MOD1J RACK-12 RACK-11 RACK-10

DKU-11

DKC-F810I-CC4/ DKC-F810I-CC4/
FC5/FC30/FC1J HDU
FC5/FC30/FC1J
DKC-F810I
-CC2

DKU-10 DKC-F810I
DKU15 DKU-13 -CC2

HDU
HDU HDU DKC-F810I
DKC-F810I -CC1 (inner
-CC2 connection)

DKA 2 DKC-F810I
DKC-F810I -CC2
-CC2 DKU-14 DKU-12
DKC-1
DKC-F810I
HDU HDU CPEX CPEX -CBXB
2 3
DKC-F810I
-CPEX
DKC-F810I-CC4/FC5/FC30/FC1J DKC-F810I-CC4/FC5/FC30/FC1J

Fig. 3.11.4.1-1 Twin DKC Configurations and Required I/F Cable Options
(Standard Model)

INST03-11C-40
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-50

RACK-00 RACK-01

DKC-F810I-
CC4/FC5/FC30/FC1J
DKC-F810I
-CC1 DKC-F810I-
DKC-F810I-FBX CC4/FC5/FC30/FC1J
DKU-01

FMD DKU-03 DKC-F810I

-UBX/SBX
DKC-F810I-CC1
HDD
DKU-00
DKC-F810I-CC2
DKC-F810I-FBX
FMD
DKC-F810I-CC2

DKC-F810I-CC2
DKU-02
DKA-0

DKC-F810I-SCA HDD
DKC-F810I
DKC-0 DKC-F810I-CC1 -UBX/SBX
DKC810I-CBXA (inner connection)

Fig. 3.11.4.1-2 Single DKC Configurations and Required I/F Cable Options
(FMD Standard Model)

RACK-10 RACK-00 RACK-01

DKU-10
DKC-F810I-FBX

FMD
DKC-F810I-CC2 DKC-F810I-CC1
(inner connection)

DKC-F810I-MOD5 DKC-F810I-MFC5
DKC-F810I-CC4/ DKA 2
FC5/FC30/FC1J
DKC-1 DKC-F810I
DKC-F810I-CC4/
FC5/FC30/FC1J CPEX CPEX -FC5/FC30/FC1J
2 3
DKC-F810I
DKC-F810I-FBX -FC5/FC30/FC1J
DKU-00
DKC-F810I
-SBX/UBX DKU-12 DKU-02 DKC-F810I
FMD -SBX/UBX
HDD HDD
DKC-F810I
DKC-F810I -CC2
-CC2
DKA 0
DKC-F810I DKC-F810I
-CC2 DKU-11 DKU-01
DKC-0 -CC2
CPEX CPEX DKC-F810I
DKC-F810I FMD FMD
0 1 -FBX
-FBX

DKC-F810I-CC2 DKC-F810I-CC1(inner connection)

Fig. 3.11.4.1-3 Dual DKC Configuration and Required I/F Cable Options
(Dual DKC Layout-1, Standard Model)

INST03-11C-50
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-60

RACK-10 RACK-00 RACK-01

DKU-10 DKC-F810I-FBX
DKC-F810I-CC4/
FMD DKC-F810I-CC1
FC5/FC30/FC1J
(inner connection)
DKC-F810I-FC5 DKC-F810I
-FC5/FC30/FC1J
DKU-00
DKC-F810I-CC4/ DKC-F810I
FC5/FC30/FC1J -FC5/FC30/FC1J
FMD

DKC-F810I-FC5
DKC-F810I-CC1
(inner connection)
DKC-F810I- DKC-F810I-
DKA-2 SBX/UBX
SBX/UBX DKU-12 DKU-02
DKC-1
DKC-F810I- CPEX CPEX DKC-F810I-
CC2 HDD HDD
2 3 CC2

DKC-F810I- DKC-F810I-
CC2 CC2
DKA-0
DKU-11 DKU-01
DKC-0
DKC-F810I-
DKC-F810I- FMD CPEX CPEX FMD FBX
FBX 0 1

DKC-F810I-MOD5 DKC-F810I-MFC5

Fig. 3.11.4.1-4 Dual DKC Configuration and Required I/F Cable Options
(Dual DKC Layout-2, Standard Model)

RACK-10 RACK-00 RACK-01

DKC-F810I-CC1
DKU-01 DKC-F810I-FBX
DKC-F810I-FC5
FMD DKC-F810I-CC1
DKC-F810I-
FC5/FC30/FC1J DKC-F810I-CC4/
FC5/FC30/FC1J
DKC-F810I- DKU-00
SBX/UBX DKU-12 DKC-F810I-CC4/
FC5/FC30/FC1J
FMD
DKC-F810I-CC1
HDD (inner connection)
DKU-03
DKC-F810I-
CC2 DKA-2 DKC-F810I-
SBX/UBX
DKC-F810I- DKU-11 HDD
DKC-1
CC2
CPEX CPEX
FMD 2 3 DKC-F810I-
CC2
DKC-F810I-
CC1 DKC-F810I-
DKA-0 DKU-02
CC2
DKC-F810I- DKU-10
CC1 DKC-0
HDD DKC-F810I-
DKC-F810I- FMD CPEX CPEX SBX/UBX
FBX 0 1

DKC-F810I-CC1
(inner connection) DKC-F810I-MOD5 DKC-F810I-MFC5

Fig. 3.11.4.1-5 Dual DKC Configuration and Required I/F Cable Options
(Dual DKC Layout-3, Standard Model)

INST03-11C-60
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-70

2. In the case of High Performance Model

The storage system configuration and number of required options for the High Performance
model are shown below.

Table 3.11.4.1-3 Requisite Options for High Performance Model (Single and Twin
DKC model)
No. Required Number of Options
DKC810I DKC-F810I- 2.5-inch 3.5-inch FMD
-CBXA CBXB RK42 SBX UBX FBX SCA CC1 CC2 CC4 MOD5 HDD HDD (*1)
(*1) (*1)
1 1 — 1 1 — — 2 — 2 — — 192 — —
2 1 — 1 2 — — 2 — 4 — — 384 — —
3 1 — 2 3 — — 2 — 4 2 — 576 — —
4 1 — 2 4 — — 2 — 6 2 — 768 — —
5 1 — 2 5 — — 2 — 6 4 — 960 — —
6 1 — 3 6 — — 2 — 8 4 — 1152 — —
7 1 1 3 7 — — 4 — 10 4 1 1344 — —
8 1 1 3 8 — — 4 — 12 4 1 1536 — —
9 1 1 4 9 — — 4 — 12 6 1 1728 — —
10 1 1 4 10 — — 4 — 14 6 1 1920 — —
11 1 1 5 11 — — 4 — 14 8 1 2112 — —
12 1 1 5 12 — — 4 — 16 8 1 2304 — —
13 1 — 1 — 1 — 2 — 2 — — — 96 —
14 1 — 1 — 2 — 2 — 4 — — — 192 —
15 1 — 2 — 3 — 2 — 4 2 — — 288 —
16 1 — 2 — 4 — 2 — 6 2 — — 384 —
17 1 — 2 — 5 — 2 — 6 4 — — 480 —
18 1 — 3 — 6 — 2 — 8 4 — — 576 —
19 1 1 3 — 7 — 4 — 10 4 1 — 672 —
20 1 1 3 — 8 — 4 — 12 4 1 — 768 —
21 1 1 4 — 9 — 4 — 12 6 1 — 864 —
22 1 1 4 — 10 — 4 — 14 6 1 — 960 —
23 1 1 5 — 11 — 4 — 14 8 1 — 1056 —
24 1 1 5 — 12 — 4 — 16 8 1 — 1152 —
25 1 — 1 — - 1 2 — 2 — — — — 48
26 1 — 1 — - 2 2 2 2 — — — — 96
27 1 1 2 — - 3 4 2 4 — 1 — — 144
28 1 1 2 — - 4 4 4 4 — 1 — — 192
29 1 1 1 — - 2 4 - 4 — 1 — — 96

*1: The maximum number of installable HDDs/FMDs includes the spare disk(s).

INST03-11C-70
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-80

Table 3.11.4.1-4 Requisite Options for High Performance Model (Dual DKC model)
Required Number of Options
No. DKC810I DKC-F810I- FMD Remarks
-CBXA CBXB RK42 FBX SCA CC1 CC2 CC4 FC5 MOD5 (*1)
1 1 1 1 2 4 — 4 — — 1 96 Dual DKC Layout-1
2 1 1 2 3 4 — 4 — 2 1 144 Dual DKC Layout-1
3 1 1 3 4 4 — 4 2 2 1 192 Dual DKC Layout-1
4 1 1 1 2 4 — — — 4 1 96 Dual DKC Layout-2
5 1 1 2 3 4 — — — 6 1 144 Dual DKC Layout-2
6 1 1 3 4 4 — — 2 6 1 192 Dual DKC Layout-2
7 1 1 2 2 4 — — — 4 1 96 Dual DKC Layout-3
8 1 1 2 3 4 2 — — 4 1 144 Dual DKC Layout-3
9 1 1 2 4 4 4 — — 4 1 192 Dual DKC Layout-3

*1: The maximum number of installable FMDs includes the spare drive(s).

INST03-11C-80
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-90

RACK-00 RACK-01 RACK-02

DKC-F810I DKU-01 DKC-F810I-

-SBX DKC-F810I-
CC4/FC5/FC30/FC1J
CC4/FC5/FC30/FC1J
HDU
DKC-F810I DKC-F810I-
-CC2 CC4/FC5/FC30/FC1J

DKC-F810I DKU-00
-CC2 DKU-03 DKU-05
DKC-F810I
-SBX HDU
HDU HDU
DKC-F810I
-CC2 DKC-F810I
-CC2
DKC-F810I DKA 0 DKA 1
-CC2 DKU-02 DKU-04 DKC-F810I
DKC-0 -CC2
DKC-F810I
-SCA CPEX CPEX HDU HDU
0 1
DKC810I
-CBXA
DKC-F810I-MFC5/ DKC-F810I-CPEX DKC-F810I-CC4/FC5/FC30/FC1J
MFC30/MFC1J
DKC-F810I-MOD5/
MOD30/MOD1J RACK-12 RACK-11 RACK-10

DKU-11

DKC-F810I-CC4/ DKC-F810I-CC4/
FC5/FC30/FC1J HDU
FC5/FC30/FC1J
DKC-F810I
-CC2

DKU-10 DKC-F810I
DKU15 DKU-13 -CC2

HDU
HDU HDU DKC-F810I
DKC-F810I -CC2
-CC2
DKC-F810I
DKA 2 DKA 3 -CC2
DKC-F810I
-CC2 DKU-14 DKU-12
DKC-1
DKC-F810I
HDU HDU CPEX CPEX -CBXB
2 3
DKC-F810I
-CPEX
DKC-F810I-CC4/FC5/FC30/FC1J DKC-F810I-CC4/FC5/FC30/FC1J

Fig. 3.11.4.1-6 Twin DKC Configurations and Required I/F Cable Options
(High Performance Model)

INST03-11C-90
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-100

RACK-10 RACK-00

DKU-11 DKU-01 DKC-F810I-FBX

FMD FMD
DKC-F810I-CC1 DKC-F810I-CC1

DKC-F810I-CC1
DKU-10 DKU-00 DKC-F810I-CC1

DKC-F810I-FBX
FMD FMD
DKC-F810I-CC2 DKC-F810I-CC2

DKC-F810I-CC2 DKC-F810I-CC2
DKA 2 DKA 3 DKA 0 DKA 1

DKC-F810I-SCA DKC-1 DKC-0 DKC810I-CBXA

CPEX CPEX CPEX CPEX
2 3 0 1
DKC-F810I-CPEX
DKC-F810I-CBXB

DKC-F810I-CPEX

DKC-F810I-
MOD5/MOD30/MOD1J DKC-F810I-MFC5/MFC30/MFC1J

Fig. 3.11.4.1-7 Twin DKC Configuration and Required I/F Cable Options
(FMD High Performance Model)

RACK-10 RACK-00 RACK-01

DKU-10
DKC-F810I-FBX

FMD
DKC-F810I-CC2 DKC-F810I-CC2

DKC-F810I-MOD5 DKC-F810I-MFC5
DKC-F810I-CC4/ DKA 2 DKA 3
FC5/FC30/FC1J
DKC-1 DKC-F810I
DKC-F810I-CC4/
FC5/FC30/FC1J CPEX CPEX -FC5/FC30/FC1J
2 3
DKC-F810I
DKC-F810I-FBX -FC5/FC30/FC1J
DKU-00
DKC-F810I
-SBX/UBX DKU-12 DKU-02 DKC-F810I
FMD -SBX/UBX
HDD HDD
DKC-F810I DKC-F810I
-CC2 -CC2
DKA 0 DKA 1
DKC-F810I DKC-F810I
-CC2 DKU-11 DKU-01
DKC-0 -CC2
CPEX CPEX DKC-F810I
DKC-F810I FMD FMD
0 1 -FBX
-FBX

DKC-F810I-CC2 DKC-F810I-CC2

Fig. 3.11.4.1-8 Dual DKC Configuration and Required I/F Cable Options
(Dual DKC Layout-1, High Performance Model)
INST03-11C-100
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-110

RACK-10 RACK-00 RACK-01

DKU-10
DKC-F810I-FBX
DKC-F810I-CC4/
FC5/FC30/FC1J FMD DKC-F810I-FC5

DKC-F810I-FC5 DKC-F810I
-FC5/FC30/FC1J
DKU-00
DKC-F810I-CC4/ DKC-F810I
FC5/FC30/FC1J -FC5/FC30/FC1J
FMD

DKC-F810I-FC5 DKC-F810I-FC5

DKC-F810I- DKC-F810I-
DKA-2 DKA-3 SBX/UBX
SBX/UBX DKU-12 DKU-02
DKC-1
DKC-F810I- CPEX CPEX DKC-F810I-
CC2 HDD HDD
2 3 CC2

DKC-F810I- DKC-F810I-
CC2 CC2
DKA-0 DKA-1
DKU-11 DKU-01
DKC-0
DKC-F810I-
DKC-F810I- FMD CPEX CPEX FMD FBX
FBX 0 1

DKC-F810I-MOD5 DKC-F810I-MFC5

Fig. 3.11.4.1-9 Dual DKC Configuration and Required I/F Cable Options
(Dual DKC Layout-2, High Performance Model)

RACK-10 RACK-00 RACK-01

DKC-F810I-CC1
DKU-01 DKC-F810I-FBX
DKC-F810I-FC5
DKC-F810I- DKC-F810I-CC1
FMD
FC5/FC30/FC1J
DKC-F810I- DKC-F810I-CC4/
FC5/FC30/FC1J FC5/FC30/FC1J
DKC-F810I- DKU-00
SBX/UBX DKU-12 DKC-F810I-CC4/
FC5/FC30/FC1J
FMD
DKC-F810I-FC5
HDD

DKU-03
DKC-F810I-
CC2 DKA-2 DKA-3 DKC-F810I-
SBX/UBX
DKC-F810I- DKU-11 HDD
DKC-1
CC2
CPEX CPEX
FMD 2 3 DKC-F810I-
CC2
DKC-F810I-
CC1 DKC-F810I-
DKA-0 DKA-1 DKU-02
CC2
DKC-F810I- DKU-10
CC1 DKC-0
HDD DKC-F810I-
DKC-F810I- FMD CPEX CPEX SBX/UBX
FBX 0 1

DKC-F810I-MOD5 DKC-F810I-MFC5

Fig. 3.11.4.1-10 Dual DKC Configuration and Required I/F Cable Options
(Dual DKC Layout-3, High Performance Model)

INST03-11C-110
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-120

3.11.4.2 Attachment of Location Labels for Device Interface Cable (DKC-F810I-CC1/CC2/CC4)

1. When you need to install DKC-F810I-CC1, attach the location labels to the cables.
When you do not need to install DKC-F810I-CC1, go to Procedure 2.

a. Attach 32 location labels to 16 cables. Choose location labels from Labels (Address) and
Labels (Address) 2. See Fig. 3.11.4.2-1 and Table 3.11.4.2-1.
b. Stick the Label (Protect) around the attached location labels.

Location Label  Location Label 

80mm 80mm

Cable
[Label Attachment Example]
Cable

Location Label

Edge

Label (Protect)

 Attach the location label to the MFC cable.

 Attach the Label (Protect) to the location label with its edge aligned with the location label.
 Stick the Label (Protect) around the location label so that the location label is not torn off.

Fig. 3.11.4.2-1 Attachment of Location Labels

Table 3.11.4.2-1 Location Label List (DKU-xy – DKU-x(y+1), CC1 × 2)

No. Connection Source (DKU-xy) Connection Destination (DKU-x(y+1))
Part Name Location Label  Label Color Part Name Location Label Label Color
1 SSWxy0-1 CL1 0-2 White/Black SSWx(y+1)0-1 CL1 0-0 White/Black
2 SSWxy0-1 CL1 1-2 White/Brown SSWx(y+1)0-1 CL1 1-0 White/Brown
3 SSWxy1-1 CL1 2-2 White/Red SSWx(y+1)1-1 CL1 2-0 White/Red
4 SSWxy1-1 CL1 3-2 White/Orange SSWx(y+1)1-1 CL1 3-0 White/Orange
5 SSWxy2-1 CL1 4-2 White/Yellow SSWx(y+1)2-1 CL1 4-0 White/Yellow
6 SSWxy2-1 CL1 5-2 White/Green SSWx(y+1)2-1 CL1 5-0 White/Green
7 SSWxy3-1 CL1 6-2 White/Blue SSWx(y+1)3-1 CL1 6-0 White/Blue
8 SSWxy3-1 CL1 7-2 White/Purple SSWx(y+1)3-1 CL1 7-0 White/Purple
9 SSWxy0-2 CL2 0-2 Yellow/Black SSWx(y+1)0-2 CL2 0-0 Yellow/Black
10 SSWxy0-2 CL2 1-2 Yellow/Brown SSWx(y+1)0-2 CL2 1-0 Yellow/Brown
11 SSWxy1-2 CL2 2-2 Yellow/Red SSWx(y+1)1-2 CL2 2-0 Yellow/Red
12 SSWxy1-2 CL2 3-2 Yellow/Orange SSWx(y+1)1-2 CL2 3-0 Yellow/Orange
13 SSWxy2-2 CL2 4-2 Yellow/Yellow SSWx(y+1)2-2 CL2 4-0 Yellow/Yellow
14 SSWxy2-2 CL2 5-2 Yellow/Green SSWx(y+1)2-2 CL2 5-0 Yellow/Green
15 SSWxy3-2 CL2 6-2 Yellow/Blue SSWx(y+1)3-2 CL2 6-0 Yellow/Blue
16 SSWxy3-2 CL2 7-2 Yellow/Purple SSWx(y+1)3-2 CL2 7-0 Yellow/Purple
INST03-11C-120
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-130

2. When you need to install DKC-F810I-CC2, attach the location labels to the cables.
When you do not need to install DKC-F810I-CC2, go to Procedure 3.

a. Attach 32 location labels to 16 cables. Choose location labels from Labels (Address) and
Labels (Address) 2. See Fig. 3.11.4.2-2 and Table 3.11.4.2-2.
b. Stick the Label (Protect) around the attached location labels.

Location Label  Location Label 

80mm 80mm

Cable
[Label Attachment Example]
Cable

Location Label

Edge

Label (Protect)

 Attach the location label to the MFC cable.

 Attach the Label (Protect) to the location label with its edge aligned with the location label.
 Stick the Label (Protect) around the location label so that the location label is not torn off.

Fig. 3.11.4.2-2 Attachment of Location Labels

Table 3.11.4.2-2 Location Label List (DKU-xy – DKU-x(y+1), CC2 × 2)

No. Connection Source (DKU-xy) Connection Destination (DKU-x(y+1))
Part Name Location Label Color Part Name Location Label Color
UBX/SBX FBX Label  UBX/SBX FBX Label
1 SSWxy0-1 SSWxy0-1 CL1 0-2 White/Black SSWx(y+1)0-1 SSWx(y+1)0-1 CL1 0-0 White/Black
2 SSWxy1-1 SSWxy0-1 CL1 1-2 White/Brown SSWx(y+1)1-1 SSWx(y+1)0-1 CL1 1-0 White/Brown
3 SSWxy2-1 SSWxy1-1 CL1 2-2 White/Red SSWx(y+1)2-1 SSWx(y+1)1-1 CL1 2-0 White/Red
4 SSWxy3-1 SSWxy1-1 CL1 3-2 White/Orange SSWx(y+1)3-1 SSWx(y+1)1-1 CL1 3-0 White/Orange
5 SSWxy4-1 SSWxy2-1 CL1 4-2 White/Yellow SSWx(y+1)4-1 SSWx(y+1)2-1 CL1 4-0 White/Yellow
6 SSWxy5-1 SSWxy2-1 CL1 5-2 White/Green SSWx(y+1)5-1 SSWx(y+1)2-1 CL1 5-0 White/Green
7 SSWxy6-1 SSWxy3-1 CL1 6-2 White/Blue SSWx(y+1)6-1 SSWx(y+1)3-1 CL1 6-0 White/Blue
8 SSWxy7-1 SSWxy3-1 CL1 7-2 White/Purple SSWx(y+1)7-1 SSWx(y+1)3-1 CL1 7-0 White/Purple
9 SSWxy0-2 SSWxy0-2 CL2 0-2 Yellow/Black SSWx(y+1)0-2 SSWx(y+1)0-2 CL2 0-0 Yellow/Black
10 SSWxy1-2 SSWxy0-2 CL2 1-2 Yellow/Brown SSWx(y+1)1-2 SSWx(y+1)0-2 CL2 1-0 Yellow/Brown
11 SSWxy2-2 SSWxy1-2 CL2 2-2 Yellow/Red SSWx(y+1)2-2 SSWx(y+1)1-2 CL2 2-0 Yellow/Red
12 SSWxy3-2 SSWxy1-2 CL2 3-2 Yellow/Orange SSWx(y+1)3-2 SSWx(y+1)1-2 CL2 3-0 Yellow/Orange
13 SSWxy4-2 SSWxy2-2 CL2 4-2 Yellow/Yellow SSWx(y+1)4-2 SSWx(y+1)2-2 CL2 4-0 Yellow/Yellow
14 SSWxy5-2 SSWxy2-2 CL2 5-2 Yellow/Green SSWx(y+1)5-2 SSWx(y+1)2-2 CL2 5-0 Yellow/Green
15 SSWxy6-2 SSWxy3-2 CL2 6-2 Yellow/Blue SSWx(y+1)6-2 SSWx(y+1)3-2 CL2 6-0 Yellow/Blue
16 SSWxy7-2 SSWxy3-2 CL2 7-2 Yellow/Purple SSWx(y+1)7-2 SSWx(y+1)3-2 CL2 7-0 Yellow/Purple

INST03-11C-130
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-140

3. When you need to install DKC-F810I-CC4, attach the location labels to the cables.
When you do not need to install DKC-F810I-CC4, go to Procedure 3.11.4.3.

a. Attach 32 location labels to 16 cables. Choose location labels from Labels (Address) and
Labels (Address) 2.
b. Stick the Label (Protect) around the attached location labels.

Location Label  Location Label 

80mm 80mm

Cable
[Label Attachment Example]
Cable

Location Label

Edge

Label (Protect)

 Attach the location label to the MFC cable.

 Attach the Label (Protect) to the location label with its edge aligned with the location label.
 Stick the Label (Protect) around the location label so that the location label is not torn off.

Fig. 3.11.4.2-3 Attachment of Location Labels

Table 3.11.4.2-3 Location Label List (DKU-xy – DKU-x(y+1), CC4 × 2)

No. Connection Source (DKU-xy) Connection Destination (DKU-x(y+1))
Part Name Location Label Color Part Name Location Label Color
UBX/SBX FBX Label  UBX/SBX FBX Label
1 SSWxy0-1 SSWxy0-1 CL1 0-2 White/Black SSWx(y+1)0-1 SSWx(y+1)0-1 CL1 0-0 White/Black
2 SSWxy1-1 SSWxy0-1 CL1 1-2 White/Brown SSWx(y+1)1-1 SSWx(y+1)0-1 CL1 1-0 White/Brown
3 SSWxy2-1 SSWxy1-1 CL1 2-2 White/Red SSWx(y+1)2-1 SSWx(y+1)1-1 CL1 2-0 White/Red
4 SSWxy3-1 SSWxy1-1 CL1 3-2 White/Orange SSWx(y+1)3-1 SSWx(y+1)1-1 CL1 3-0 White/Orange
5 SSWxy4-1 SSWxy2-1 CL1 4-2 White/Yellow SSWx(y+1)4-1 SSWx(y+1)2-1 CL1 4-0 White/Yellow
6 SSWxy5-1 SSWxy2-1 CL1 5-2 White/Green SSWx(y+1)5-1 SSWx(y+1)2-1 CL1 5-0 White/Green
7 SSWxy6-1 SSWxy3-1 CL1 6-2 White/Blue SSWx(y+1)6-1 SSWx(y+1)3-1 CL1 6-0 White/Blue
8 SSWxy7-1 SSWxy3-1 CL1 7-2 White/Purple SSWx(y+1)7-1 SSWx(y+1)3-1 CL1 7-0 White/Purple
9 SSWxy0-2 SSWxy0-2 CL2 0-2 Yellow/Black SSWx(y+1)0-2 SSWx(y+1)0-2 CL2 0-0 Yellow/Black
10 SSWxy1-2 SSWxy0-2 CL2 1-2 Yellow/Brown SSWx(y+1)1-2 SSWx(y+1)0-2 CL2 1-0 Yellow/Brown
11 SSWxy2-2 SSWxy1-2 CL2 2-2 Yellow/Red SSWx(y+1)2-2 SSWx(y+1)1-2 CL2 2-0 Yellow/Red
12 SSWxy3-2 SSWxy1-2 CL2 3-2 Yellow/Orange SSWx(y+1)3-2 SSWx(y+1)1-2 CL2 3-0 Yellow/Orange
13 SSWxy4-2 SSWxy2-2 CL2 4-2 Yellow/Yellow SSWx(y+1)4-2 SSWx(y+1)2-2 CL2 4-0 Yellow/Yellow
14 SSWxy5-2 SSWxy2-2 CL2 5-2 Yellow/Green SSWx(y+1)5-2 SSWx(y+1)2-2 CL2 5-0 Yellow/Green
15 SSWxy6-2 SSWxy3-2 CL2 6-2 Yellow/Blue SSWx(y+1)6-2 SSWx(y+1)3-2 CL2 6-0 Yellow/Blue
16 SSWxy7-2 SSWxy3-2 CL2 7-2 Yellow/Purple SSWx(y+1)7-2 SSWx(y+1)3-2 CL2 7-0 Yellow/Purple

INST03-11C-140
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-150

3.11.4.3 Setting up the New Device Structure Information

(1) <Mode Change>
Change the mode to Modify Mode.
Select (CL) [Install].

(2) <Start the ‘Menu Dialog’ screen>

Select (CL) [Change Configuration].

(3) <Start Device Structure Setup screen>

Select (CL) [Installation] in the “Menu
Dialog” dialog box and select (CL) [OK].

(4) <Select a changed part>

Select (CL) [ECC group + LDEV], and select
(CL) [OK].

INST03-11C-150
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-160

(5) <DKC Configuration screen>

In the ‘DKC Configuration’ screen, select
(CL) [>>Next].
Go to Step (6).
In the case of selecting (CL) [Cancel], this
operation procedure terminates.

NOTE: There may be a case where an

addition of the SM is required to add
the CU.

INST03-11C-160
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-170

(6) <DKU Equipment Configuration screen>

Define the pattern of DKU Equipment in the
‘DKU Equipment Configuration’ screen.

When you want to set the DKU type, select

(CL) the installed target DKU, and then select
(CL) [DKU Kind].
Go to Step (6)-1.
After setting, select (CL) [>>Next].
Go to Step (7).

(6)-1 <DKU Kind Define screen>

Set DKU Kind select (CL) [OK].
Go back to Step (6).

INST03-11C-170
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-180

(7) <Change Drive Configuration Information>

Define the drive configuration according to
the ‘Physical Device Configuration’ screen.
Detailed procedure is shown below.
[Set...]: Defines the parity group or spare
disk.
Go to Step (8).
[Clear]: Cancels the setting of the B4.
After setting up all items, select (CL)
[>>Next].
Go to Step (9).

Selecting (CL) [Before<<] returns to Step (6).

• Relation between B4 and HDU Location (Refer to LOC02-40 ~ 80 for Location.)

B4 Location B4 Location
DKU HDU DKU HDU
1st DKU-00 HDU-000, 001, 002, 003 13th DKU-03 HDU-030, 031, 032, 033
2nd DKU-00 HDU-004, 005, 006, 007 14th DKU-03 HDU-034, 035, 036, 037
3rd DKU-10 HDU-100, 101, 102, 103 15th DKU-13 HDU-130, 131, 132, 133
4th DKU-10 HDU-104, 105, 106, 107 16th DKU-13 HDU-134, 135, 136, 137
5th DKU-01 HDU-010, 011, 012, 013 17th DKU-04 HDU-040, 041, 042, 043
6th DKU-01 HDU-014, 015, 016, 017 18th DKU-04 HDU-044, 045, 046, 047
7th DKU-11 HDU-110, 111, 112, 113 19th DKU-14 HDU-140, 141, 142, 143
8th DKU-11 HDU-114, 115, 116, 117 20th DKU-14 HDU-144, 145, 146, 147
9th DKU-02 HDU-020, 021, 022, 023 21st DKU-05 HDU-050, 051, 052, 053
10th DKU-02 HDU-024, 025, 026, 027 22nd DKU-05 HDU-054, 055, 056, 057
11th DKU-12 HDU-120, 121, 122, 123 23rd DKU-15 HDU-150, 151, 152, 153
12th DKU-12 HDU-124, 125, 126, 127 24th DKU-15 HDU-154, 155, 156, 157

INST03-11C-180
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-190

(8) <Define Parity Group>

The ‘Parity Group Configuration’ dialog box
is displayed.
[Group...]: Defines the parity group.
See Step (8)-1.
[Spare...]: Defines the spare drive.
See Step (8)-2.
[Delete]: Deletes the added parity group or
spare drive.

Grp*: A parity group where RAID

Concatenation is installed.

NOTE: If you want to set any Spare Drives

in B4, please define the Spare Drives first.

After setting up all items, select (CL) [OK].

Go back to Step (7).

INST03-11C-190
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-200

(8)-1
Define the RAID Level, the Drive Type, and
the Number of Parity Group in the ‘Parity
Group’ dialog box.
Then select (CL) [OK].
Go back to Step (8).

(8)-2
Define the Drive Type and the Number of
Spare Drives in the ‘Spare’ dialog box.
Then select (CL) [OK].
Go back to Step (8).

INST03-11C-200
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-210

(9) <Define Device Emulation>

After setting up all items corresponding (9)-1 to (9)-3 for definition of Device Emulation,
select (CL) [>>Next].
Selecting (CL) [Before<<] returns you to the previous screen.
In the case of only spare drive installation, select (CL) [>>Next]. Go to Step (10).
• If defining Device Emulation, go to Step (9)-1.
• If setting RAID concatenation, go to Step (9)-2.
• If defining of Customized Volume Size (CVS), go to Step (9)-3.

(9)-1 <Define Device Emulation>

Select (CL) parity group and select (CL)
[Set...]. Go to Step (9)-1-1.

(CVS): A parity group where CVS is

installed.
Grp*: A parity group where RAID
Concatenation is installed.

(9)-1-1
After setting up all items in the ‘Device Emulation
Type Define’ dialog box, select (CL) [OK].
Go back to Step (9).

Selecting (CL) [Cancel] returns to Step (9)-1

without reflecting the setting items.
NOTE: OPEN-V is a recommended OPEN volume.
To set other than OPEN-V, please select
“Except OPEN-V”.
NOTE: “0” can be set to the value of Number of
LDEVs for all the emulation types.
If you don’t know the LDEV size you will use, set “0”. You can save time by setting
“0” because LDEV format will not run.
When you set “0”, please make LDEVs later using the CVS function.
NOTE: If 3390-A is selected, a 3390-A volume whose capacity is as large as that of standard
capacity of the specified emulation type can be created by specifying (3390-3 size),
(3390-9 size), (3390-L size), or (3390-M size) in the “Number of LDEVs”. If a parity
group consists of drives with 1TB or larger is specified, only (3390-M size) can be
selected in the “Number of LDEVs”.

INST03-11C-210
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-220

(9)-2 <Setting RAID concatenation>

Select (CL) [Concatenate...].
When setting RAID concatenation is not executed, go back to Step (9).

(9)-2-1
Parity groups to which the RAID
concatenation can be applied are displayed in
the Parity group List.
Select (CL) parity groups to which you want
to apply the RAID concatenation and press
(CL) the [>>] button. Go to Step (9)-2-2.

NOTE: Only the parity groups, which have

been added and to which the RAID
concatenation can be applied are
displayed in the Parity group List.

(9)-2-2
The selected parity groups are registered in
the Concatenate Parity group List. Then press
(CL) the [Concatenate] button. Go to Step
(9)-2-3.

NOTE: The [Concatenate] button cannot be

pressed if the concatenation does not
meet a condition of the RAID
concatenation. Adjust the number of
the parity groups in the Concatenate
Parity group List.

INST03-11C-220
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-230

(9)-2-3
When the RAID concatenation is completed,
“(Concatenation)” is displayed in the Parity
group List. Selecting the “(Concatenation)”
displays the concatenated parity groups in the
Concatenation List.
Pressing the [Clear] button cancels the RAID
concatenation.

When all the settings of the RAID

concatenation are completed, press (CL) the
[OK] button. Go back to Step (9).
Pressing (CL) the [Cancel] button returns the routine to Step (9).

INST03-11C-230
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-240

(9)-3 <Defining of Customized Volume Size (CVS)>

Select (CL) a parity group for which the
LDEV emulation type and the number of
LDEVs have been set on the ‘Device
Emulation Configuration’ screen and select
(CL) [Detail…].
When you do not perform the CVS, go back
to Step (9).

INST03-11C-240
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-250

(9)-3-1
A volume other than OPEN-V can be defined
in the ‘Customized Volume Size Define’
screen.
• Set of a CVS volume
Perform  Delete of the Volume and 
Add of the Volume.

 Delete of the Volume

A volume can be deleted by selecting (CL)
the volume from the LDEV list box and
selecting (CL) [Delete].
 Add of the Volume
A volume can be added by entering the LDEV emulation type and the user size
(Mbyte/Blocks or Cylinder) of the customized volume (CV) and selecting [Add].
(It can be added in the optional space “empty” by selecting (CL) “empty” from the LDEV
list box.)
The two or more CVs can be registered when the operation above is performed repeatedly.

The boundary correction existence is specifiable with “Offset Boundary”.

(When a volume for mainframe host is selected, it is not possible to select it.)

Adding or deleting operation can be done for any number of times. The last setting is reflected
by selecting (CL) [OK].

NOTE: The two or more volumes can be selected and deleted.

The routine returns to the preceding window by selecting (CL) [Cancel].

The routine returns to the preceding window and the change is reflected by selecting (CL)
[OK].

INST03-11C-250
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-260

(9)-3-2 <Definition of OPEN-V>

OPEN-V can be defined in the ‘Variable
Volume Size Define’ window.
• Set of a CVS volume
Perform  Delete of the Volume and 
Add of the Volume.

 Delete of the Volume

The volume can be deleted by selecting
(CL) [Delete] in the state (CL) of selecting (CL) the volume in the LDEV list box.
All the volumes in the LDEV list box can be deleted by selecting (CL) [Clear].
 Add of the Volume
It can be added by selecting (CL) Variable Volume Size from the status “select (CL)
‘empty’” or “no selection” in the LDEV list box and selecting (CL) [Add].

Adding or deleting operation can be done for any number of times. The last setting is reflected
by selecting (CL) [OK].

NOTE: The two or more volumes can be selected and deleted.

• Variable Volume Size

“Specify size & number” : Defines the specified number of the specified user size.
• Offset Boundary : The boundary correction existence is specified.
• Capacity Unit
“MByte” : Makes data displayed or entered by [MByte].
“Cylinder” : Makes data displayed or entered by the [Cylinder].
“Blocks” : Makes data displayed or entered by the [Blocks].
• asst. : When Path/pool-VOL is defined, “+” is displayed.
NOTE: Even if the journal volume is defined, “+” is not
displayed.
[Clear] : Deletes all the volumes.
[Delete] : Deletes all the selected volumes.
[Add] : Adds volumes.
[Cancel] : Invalidates the setting, and returns to the preceding window.
[OK] : Confirms the setting, and returns to the preceding window.

INST03-11C-260
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-270

(10) <Define LDEV ID>

(10)-1
Definition Screen for LDEV ID.
Select (CL) the parity group to be defined and
select (CL) a function from the [LDEV ID] list
box.
[Linear...]: LDEV ID is assigned to LDEV in
the order of parity groups. See
Step (10)-3.
[Disperse...]: LDEV is assigned discretely in the
order of parity groups. See Step
(10)-3.
[Detail...]: A screen to define LDEV in detail
is displayed. See Step (10)-2.
(When plural groups are selected
(CL), it is invalid.)
[Clear]: Select (CL) [Clear] to delete.
Grp*: The top parity group where RAID Concatenation is installed.
Status: Status of LDEV ID.
 “Complete” : LDEV ID is assigned.
 “-------” : LDEV ID is not assigned.
 “Error” : Invalid LDEV ID is assigned.
After setting up all items, select (CL) [Detail...] to confirm the items that have been setup, and
select (CL) [>>Next]. Go to Step (11).

INST03-11C-270
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-280

(10)-2 <Detailed Definition Screen for LDEV ID>

LDEV ID is defined in detail for each LDEV
in the parity group.
Select (CL) LDEV from the list box and
select (CL) [Change...].
The screen for LDEV ID input is displayed.
After setting, select (CL) [OK]. Go back to
Step (10)-1.
• ‘-----’ is displayed in the CU area and the ID
area for the LDEV to which LDEV ID is not
assigned.
NOTE: In the case of a RAID Concatenation
Group, LDEV of the parity group
selected by the “Grp List” is displayed.

INST03-11C-280
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-290

(10)-3 <Input LDEV ID>

Select LDKC in the LDKC pull down menu.
Select CU in the CU pull down menu.
The status of usage of ID in the CU is displayed
in the LDEV ID panel.
White disk of panel: not used
Patterned disk of panel: using
Input LDEV ID you want to set or the head
LDEV ID in the ID Edit box.
After setting, select (CL) [OK].
Go back to Step (10)-1.
NOTE: The definition range (terminal) is
decided with LDEV Range.
For example, if LEDV Range is defined
as 7F, LDEV ID is assigned only within the range of 00 to 7F.

(11) <Define SSID>

To define SSID, select (CL) the item from the list box
and select (CL) [SS ID...].
Go to Step (11)-1.

After setting, select (CL) [>>Next].

Go to Step (12).

(11)-1
Define SSID and select (CL) [OK].
Go back to Step (11).

INST03-11C-290
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-300

(12) <Define LDEV Management MPB>

In the ‘LDEV Management MPB
Configuration’ screen, select (CL) [Change
MPB].
Go to Step (12)-1.

After the setting is completed, select (CL)

[>>Next].
Go to Step (13).

(12)-1
Define Management MPB and select (CL) [OK].
Go back to Step (12).

INST03-11C-300
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-310

(13) <Selection of format>

Select (CL) [Yes] in response to “Do you
want to format logical devices by Quick
Format?” when you execute Quick Format.
When [No] is selected (CL), usual LDEV
Format is executed.

NOTE: Next, Quick Format cannot be

executed in the shown volume.
• external volume
• Volumes whose access attribute is not Read/Write
• Pool volumes (pool-VOLs)
• Journal volumes

When [Yes] is selected: Go to Step (13)-1.

When [No] is selected: Go to Step (14).

(13)-1 <Execution of Quick Format>

For the message “Quick Format is executed.
Do you continue to this operation?
[Yes]: Quick Format is executed.
[No]: Format is executed.”, select (CL) [Yes]
when Quick Format is to be executed. Select
(CL) [No] when normal LDEV format is to be
executed.

INST03-11C-310
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-320

(14) <Wear a wrist strap>

Select (CL) [OK] in response to “To prevent
serious failures caused by the static electrical
charge, be sure to wear a wrist strap on your
wrist and connect the earth clip attached on
the other side of the wrist strap to the chassis
frame (metal part) before starting operation.”.

(14)-1<Confirm wearing wrist strap>

In response to a message, “Did you put on a
wrist strap on your wrist?”.
Select [Yes] when wrist strap is on your wrist.
Select [No] when there is no wrist strap on
your wrist.
When [No] is selected (CL), go to Step (14)-2.

(14)-2
In response to a message, “This operation
cannot be excuted, because the wrist strap has
not been worn. Do you want to stop this
process?
[Yes]: This processing will be stopped.
[No]: This confirming message will appear.”
When [Yes] is selected (CL), the routine is
returned to Step (2) on page INST03-11C-150.
When [No] is selected (CL), returned to Step (14).

INST03-11C-320
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-330

(15) <Start installation>

Select (CL) [Yes] in response to “After you
select [Yes], you cannot cancel this operation.
Are you sure you want to continue this
operation? (Note) Do not insert the
components for upgrading the system at this
time.”.
When [No] is selected (CL), the routine is
returned to Step (2) on page INST03-11C-150.

(16) <Download microprogram>

Microprograms are automatically downloaded for each processor.

(17) <Install DKA>

“Upgrading of the DKA...”

(18) <Notes when insert of PDEV>

“Do not insert multiple PDEV at the same
time. Insert PDEV one by one with an interval
of a second or more.” is displayed.
Select (CL) [OK].

(19) <Check that hardware components are installed>

At this point refrain from pressing the [OK]
button.
“Insert the PDEV/DKU on the storage
system. Turn on the circuit breakers on the
DKUPS and PDU. After the operations are
completed, select [OK] button.” is displayed.

NOTE: When the breaker of PDU is OFF,

please turn it on.

INST03-11C-330
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-340

3.11.4.4 Installation Procedure of drive

NOTICE: If No Charging of FMD (SIM = 50EXYY) occurs in installation of a FMD, the

FMD ACTIVE LED will change to low-speed blinking. In this case, it takes 90
minutes at most for the FMD ACTIVE LED to go out and for the battery in the
FMD to be fully charged.

1. Confirmation of position to install drive

(i) RAID5 (3D+1P) / RAID1 (2D+2D), UBX (DKU for 3.5 inch Drive)
Relations between the installation locations of the RAID groups and the RAID group
numbers set through the SVP are shown in Table 3.11.4.4-1.

Table 3.11.4.4-1 Relation between drives installation order and RAID group number
(3D+1P/2D+2D, UBX) (1/2)
DKU-00 DKU-01 DKU-02 DKU-03 DKU-04 DKU-05
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
001 1-1 025 5-1 049 9-1 073 13-1 097 17-1 121 21-1
002 2-1 026 6-1 050 10-1 074 14-1 098 18-1 122 22-1
003 1-2 027 5-2 051 9-2 075 13-2 099 17-2 123 21-2
004 2-2 028 6-2 052 10-2 076 14-2 100 18-2 124 22-2
005 1-3 029 5-3 053 9-3 077 13-3 101 17-3 125 21-3
006 2-3 030 6-3 054 10-3 078 14-3 102 18-3 126 22-3
007 1-4 031 5-4 055 9-4 079 13-4 103 17-4 127 21-4
008 2-4 032 6-4 056 10-4 080 14-4 104 18-4 128 22-4
009 1-5 033 5-5 057 9-5 081 13-5 105 17-5 129 21-5
010 2-5 034 6-5 058 10-5 082 14-5 106 18-5 130 22-5
011 1-6 035 5-6 059 9-6 083 13-6 107 17-6 131 21-6
012 2-6 036 6-6 060 10-6 084 14-6 108 18-6 132 22-6
013 1-7 037 5-7 061 9-7 085 13-7 109 17-7 133 21-7
014 2-7 038 6-7 062 10-7 086 14-7 110 18-7 134 22-7
015 1-8 039 5-8 063 9-8 087 13-8 111 17-8 135 21-8
016 2-8 040 6-8 064 10-8 088 14-8 112 18-8 136 22-8
017 1-9 041 5-9 065 9-9 089 13-9 113 17-9 137 21-9
018 2-9 042 6-9 066 10-9 090 14-9 114 18-9 138 22-9
019 1-10 043 5-10 067 9-10 091 13-10 115 17-10 139 21-10
020 2-10 044 6-10 068 10-10 092 14-10 116 18-10 140 22-10
021 1-11 045 5-11 069 9-11 093 13-11 117 17-11 141 21-11
022 2-11 046 6-11 070 10-11 094 14-11 118 18-11 142 22-11
023 1-12 047 5-12 071 9-12 095 13-12 119 17-12 143 21-12
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1
024 2-12 048 6-12 072 10-12 096 14-12 120 18-12 144 22-12
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

INST03-11C-340
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-350

Table 3.11.4.4-1 Relation between drives installation order and RAID group number
(3D+1P/2D+2D, UBX) (2/2)
DKU-10 DKU-11 DKU-12 DKU-13 DKU-14 DKU-15
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
145 3-1 169 7-1 193 11-1 217 15-1 241 19-1 265 23-1
146 4-1 170 8-1 194 12-1 218 16-1 242 20-1 266 24-1
147 3-2 171 7-2 195 11-2 219 15-2 243 19-2 267 23-2
148 4-2 172 8-2 196 12-2 220 16-2 244 20-2 268 24-2
149 3-3 173 7-3 197 11-3 221 15-3 245 19-3 269 23-3
150 4-3 174 8-3 198 12-3 222 16-3 246 20-3 270 24-3
151 3-4 175 7-4 199 11-4 223 15-4 247 19-4 271 23-4
152 4-4 176 8-4 200 12-4 224 16-4 248 20-4 272 24-4
153 3-5 177 7-5 201 11-5 225 15-5 249 19-5 273 23-5
154 4-5 178 8-5 202 12-5 226 16-5 250 20-5 274 24-5
155 3-6 179 7-6 203 11-6 227 15-6 251 19-6 275 23-6
156 4-6 180 8-6 204 12-6 228 16-6 252 20-6 276 24-6
157 3-7 181 7-7 205 11-7 229 15-7 253 19-7 277 23-7
158 4-7 182 8-7 206 12-7 230 16-7 254 20-7 278 24-7
159 3-8 183 7-8 207 11-8 231 15-8 255 19-8 279 23-8
160 4-8 184 8-8 208 12-8 232 16-8 256 20-8 280 24-8
161 3-9 185 7-9 209 11-9 233 15-9 257 19-9 281 23-9
162 4-9 186 8-9 210 12-9 234 16-9 258 20-9 282 24-9
163 3-10 187 7-10 211 11-10 235 15-10 259 19-10 283 23-10
164 4-10 188 8-10 212 12-10 236 16-10 260 20-10 284 24-10
165 3-11 189 7-11 213 11-11 237 15-11 261 19-11 285 23-11
166 4-11 190 8-11 214 12-11 238 16-11 262 20-11 286 24-11
167 3-12 191 7-12 215 11-12 239 15-12 263 19-12 287 23-12
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1
168 4-12 192 8-12 216 12-12 240 16-12 264 20-12 288 24-12
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

INST03-11C-350
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-360

(1) Make sure of the location where the RAID group is installed and that where the drive is to be
added.
No. Model Number Model Name Remarks
1 DKC-F810I-3R0H3M/4R0H3M × 4 LFF Disk Drive

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-11 DKU-01
186 188 190 192*1 042 044 046 048*1
178 180 182 184 034 036 038 040
170 172 174 176 026 028 030 032
185 187 189 191*1 041 043 045 047*1
177 179 181 183 033 035 037 039
169 171 173 175 025 027 029 031
186 188 190 192*1 042 044 046 048*1
178 180 182 184 034 036 038 040
170 172 174 176 026 028 030 032
185 187 189 191*1 041 043 045 047*1
177 179 181 183 033 035 037 039
169 171 173 175 025 027 029 031
186 188 190 192*1 042 044 046 048*1
178 180 182 184 034 036 038 040
170 172 174 176 026 028 030 032
185 187 189 191*1 041 043 045 047*1
177 179 181 183 033 035 037 039
169 171 173 175 025 027 029 031
186 188 190 192*1 042 044 046 048*1
178 180 182 184 034 036 038 040
170 172 174 176 026 028 030 032
185 187 189 191*1 041 043 045 047*1
177 179 181 183 033 035 037 039
169 171 173 175 025 027 029 031
DKU-10 DKU-00
162 164 166 168*1 018 020 022 024*1
154 156 158 160 010 012 014 016
146 148 150 152 002 004 006 008
161 163 165 167*1 017 019 021 023*1
153 155 157 159 009 011 013 015
145 147 149 151 001 003 005 007
162 164 166 168*1 018 020 022 024*1
154 156 158 160 010 012 014 016
146 148 150 152 002 004 006 008
161 163 165 167*1 017 019 021 023*1
153 155 157 159 009 011 013 015
145 147 149 151 001 003 005 007
162 164 166 168*1 018 020 022 024*1
154 156 158 160 010 012 014 016
146 148 150 152 002 004 006 008
161 163 165 167*1 017 019 021 023*1
153 155 157 159 009 011 013 015
145 147 149 151 001 003 005 007
162 164 166 168*1 018 020 022 024*1
154 156 158 160 010 012 014 016
146 148 150 152 002 004 006 008
161 163 165 167*1 017 019 021 023*1
153 155 157 159 009 011 013 015
145 147 149 151 001 003 005 007
*1: A data or
DKC-1 DKC-0 spare disk
is to be
installed.

Front View Front View

Fig. 3.11.4.4-1 (3D+1P/2D+2D) Data Drive/Parity Drive Expansion Sequence (1/3)

The relationship between drives installation order and RAID group number is shown in the Table
3.11.4.4-1.
INST03-11C-360
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-370

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-13 DKU-03
234 236 238 240*1 090 092 094 096*1
226 228 230 232 082 084 086 088
218 220 222 224 074 076 078 080
233 235 237 239*1 089 091 093 095*1
225 227 229 231 081 083 085 087
217 219 221 223 073 075 077 079
234 236 238 240*1 090 092 094 096*1
226 228 230 232 082 084 086 088
218 220 222 224 074 076 078 080
233 235 237 239*1 089 091 093 095*1
225 227 229 231 081 083 085 087
217 219 221 223 073 075 077 079
234 236 238 240*1 090 092 094 096*1
226 228 230 232 082 084 086 088
218 220 222 224 074 076 078 080
233 235 237 239*1 089 091 093 095*1
225 227 229 231 081 083 085 087
217 219 221 223 073 075 077 079
234 236 238 240*1 090 092 094 096*1
226 228 230 232 082 084 086 088
218 220 222 224 074 076 078 080
233 235 237 239*1 089 091 093 095*1
225 227 229 231 081 083 085 087
217 219 221 223 073 075 077 079
DKU-12 DKU-02
210 212 214 216*1 066 068 070 072*1
202 204 206 208 058 060 062 064
194 196 198 200 050 052 054 056
209 211 213 215*1 065 067 069 071*1
201 203 205 207 057 059 061 063
193 195 197 199 049 051 053 055
210 212 214 216*1 066 068 070 072*1
202 204 206 208 058 060 062 064
194 196 198 200 050 052 054 056
209 211 213 215*1 065 067 069 071*1
201 203 205 207 057 059 061 063
193 195 197 199 049 051 053 055
210 212 214 216*1 066 068 070 072*1
202 204 206 208 058 060 062 064
194 196 198 200 050 052 054 056
209 211 213 215*1 065 067 069 071*1
201 203 205 207 057 059 061 063
193 195 197 199 049 051 053 055
210 212 214 216*1 066 068 070 072*1
*1: A data or
202 204 206 208 058 060 062 064 spare disk
194 196 198 200 050 052 054 056
is to be
209 211 213 215*1 065 067 069 071*1
201 203 205 207 057 059 061 063 installed.
193 195 197 199 049 051 053 055

Front View Front View

Fig. 3.11.4.4-1 (3D+1P/2D+2D) Data Drive/Parity Drive Expansion Sequence (2/3)

The relationship between drives installation order and RAID group number is shown in the Table
3.11.4.4-1.

INST03-11C-370
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-380

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-15 DKU-05
282 284 286 288*1 138 140 142 144*1
274 276 278 280 130 132 134 136
266 268 270 272 122 124 126 128
281 283 285 287*1 137 139 141 143*1
273 275 277 279 129 131 133 135
265 267 269 271 121 123 125 127
282 284 286 288*1 138 140 142 144*1
274 276 278 280 130 132 134 136
266 268 270 272 122 124 126 128
281 283 285 287*1 137 139 141 143*1
273 275 277 279 129 131 133 135
265 267 269 271 121 123 125 127
282 284 286 288*1 138 140 142 144*1
274 276 278 280 130 132 134 136
266 268 270 272 122 124 126 128
281 283 285 287*1 137 139 141 143*1
273 275 277 279 129 131 133 135
265 267 269 271 121 123 125 127
282 284 286 288*1 138 140 142 144*1
274 276 278 280 130 132 134 136
266 268 270 272 122 124 126 128
281 283 285 287*1 137 139 141 143*1
273 275 277 279 129 131 133 135
265 267 269 271 121 123 125 127
DKU-14 DKU-04
258 260 262 264*1 114 116 118 120*1
250 252 254 256 106 108 110 112
242 244 246 248 098 100 102 104
257 259 261 263*1 113 115 117 119*1
249 251 253 255 105 107 109 111
241 243 245 247 097 099 101 103
258 260 262 264*1 114 116 118 120*1
250 252 254 256 106 108 110 112
242 244 246 248 098 100 102 104
257 259 261 263*1 113 115 117 119*1
249 251 253 255 105 107 109 111
241 243 245 247 097 099 101 103
258 260 262 264*1 114 116 118 120*1
250 252 254 256 106 108 110 112
242 244 246 248 098 100 102 104
257 259 261 263*1 113 115 117 119*1
249 251 253 255 105 107 109 111
241 243 245 247 097 099 101 103
258 260 262 264*1 114 116 118 120*1
*1: A data or
250 252 254 256 106 108 110 112 spare disk
242 244 246 248 098 100 102 104
is to be
257 259 261 263*1 113 115 117 119*1
249 251 253 255 105 107 109 111 installed.
241 243 245 247 097 099 101 103

Front View Front View

Fig. 3.11.4.4-1 (3D+1P/2D+2D) Data Drive/Parity Drive Expansion Sequence (3/3)

The relationship between drives installation order and RAID group number is shown in the Table
3.11.4.4-1.

INST03-11C-380
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-390

(ii) RAID5 (3D+1P) / RAID1 (2D+2D), SBX (DKU for 2.5 inch Drive)
Relations between the installation locations of the RAID groups and the RAID group
numbers set through the SVP are shown in Table 3.11.4.4-2.

Table 3.11.4.4-2 Relation between drives installation order and RAID group number
(3D+1P/2D+2D, SBX) (1/4)
DKU-00 DKU-01 DKU-02
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
001 1-1 025 1-13 049 5-1 073 5-13 097 9-1 121 9-13
002 2-1 026 2-13 050 6-1 074 6-13 098 10-1 122 10-13
003 1-2 027 1-14 051 5-2 075 5-14 099 9-2 123 9-14
004 2-2 028 2-14 052 6-2 076 6-14 100 10-2 124 10-14
005 1-3 029 1-15 053 5-3 077 5-15 101 9-3 125 9-15
006 2-3 030 2-15 054 6-3 078 6-15 102 10-3 126 10-15
007 1-4 031 1-16 055 5-4 079 5-16 103 9-4 127 9-16
008 2-4 032 2-16 056 6-4 080 6-16 104 10-4 128 10-16
009 1-5 033 1-17 057 5-5 081 5-17 105 9-5 129 9-17
010 2-5 034 2-17 058 6-5 082 6-17 106 10-5 130 10-17
011 1-6 035 1-18 059 5-6 083 5-18 107 9-6 131 9-18
012 2-6 036 2-18 060 6-6 084 6-18 108 10-6 132 10-18
013 1-7 037 1-19 061 5-7 085 5-19 109 9-7 133 9-19
014 2-7 038 2-19 062 6-7 086 6-19 110 10-7 134 10-19
015 1-8 039 1-20 063 5-8 087 5-20 111 9-8 135 9-20
016 2-8 040 2-20 064 6-8 088 6-20 112 10-8 136 10-20
017 1-9 041 1-21 065 5-9 089 5-21 113 9-9 137 9-21
018 2-9 042 2-21 066 6-9 090 6-21 114 10-9 138 10-21
019 1-10 043 1-22 067 5-10 091 5-22 115 9-10 139 9-22
020 2-10 044 2-22 068 6-10 092 6-22 116 10-10 140 10-22
021 1-11 045 1-23 069 5-11 093 5-23 117 9-11 141 9-23
022 2-11 046 2-23 070 6-11 094 6-23 118 10-11 142 10-23
023 1-12 047 1-24 071 5-12 095 5-24 119 9-12 143 9-24
Spare*1 Spare*1 Spare*1
024 2-12 048 2-24 072 6-12 096 6-24 120 10-12 144 10-24
Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

INST03-11C-390
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-400

Table 3.11.4.4-2 Relation between drives installation order and RAID group number
(3D+1P/2D+2D, SBX) (2/4)
DKU-03 DKU-04 DKU-05
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
145 13-1 169 13-13 193 17-1 217 17-13 241 21-1 265 21-13
146 14-1 170 14-13 194 18-1 218 18-13 242 22-1 266 22-13
147 13-2 171 13-14 195 17-2 219 17-14 243 21-2 267 21-14
148 14-2 172 14-14 196 18-2 220 18-14 244 22-2 268 22-14
149 13-3 173 13-15 197 17-3 221 17-15 245 21-3 269 21-15
150 14-3 174 14-15 198 18-3 222 18-15 246 22-3 270 22-15
151 13-4 175 13-16 199 17-4 223 17-16 247 21-4 271 21-16
152 14-4 176 14-16 200 18-4 224 18-16 248 22-4 272 22-16
153 13-5 177 13-17 201 17-5 225 17-17 249 21-5 273 21-17
154 14-5 178 14-17 202 18-5 226 18-17 250 22-5 274 22-17
155 13-6 179 13-18 203 17-6 227 17-18 251 21-6 275 21-18
156 14-6 180 14-18 204 18-6 228 18-18 252 22-6 276 22-18
157 13-7 181 13-19 205 17-7 229 17-19 253 21-7 277 21-19
158 14-7 182 14-19 206 18-7 230 18-19 254 22-7 278 22-19
159 13-8 183 13-20 207 17-8 231 17-20 255 21-8 279 21-20
160 14-8 184 14-20 208 18-8 232 18-20 256 22-8 280 22-20
161 13-9 185 13-21 209 17-9 233 17-21 257 21-9 281 21-21
162 14-9 186 14-21 210 18-9 234 18-21 258 22-9 282 22-21
163 13-10 187 13-22 211 17-10 235 17-22 259 21-10 283 21-22
164 14-10 188 14-22 212 18-10 236 18-22 260 22-10 284 22-22
165 13-11 189 13-23 213 17-11 237 17-23 261 21-11 285 21-23
166 14-11 190 14-23 214 18-11 238 18-23 262 22-11 286 22-23
167 13-12 191 13-24 215 17-12 239 17-24 263 21-12 287 21-24
Spare*1 Spare*1 Spare*1
168 14-12 192 14-24 216 18-12 240 18-24 264 22-12 288 22-24
Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

INST03-11C-400
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-410

Table 3.11.4.4-2 Relation between drives installation order and RAID group number
(3D+1P/2D+2D, SBX) (3/4)
DKU-10 DKU-11 DKU-12
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
289 3-1 313 3-13 337 7-1 361 7-13 385 11-1 409 11-13
290 4-1 314 4-13 338 8-1 362 8-13 386 12-1 410 12-13
291 3-2 315 3-14 339 7-2 363 7-14 387 11-2 411 11-14
292 4-2 316 4-14 340 8-2 364 8-14 388 12-2 412 12-14
293 3-3 317 3-15 341 7-3 365 7-15 389 11-3 413 11-15
294 4-3 318 4-15 342 8-3 366 8-15 390 12-3 414 12-15
295 3-4 319 3-16 343 7-4 367 7-16 391 11-4 415 11-16
296 4-4 320 4-16 344 8-4 368 8-16 392 12-4 416 12-16
297 3-5 321 3-17 345 7-5 369 7-17 393 11-5 417 11-17
298 4-5 322 4-17 346 8-5 370 8-17 394 12-5 418 12-17
299 3-6 323 3-18 347 7-6 371 7-18 395 11-6 419 11-18
300 4-6 324 4-18 348 8-6 372 8-18 396 12-6 420 12-18
301 3-7 325 3-19 349 7-7 373 7-19 397 11-7 421 11-19
302 4-7 326 4-19 350 8-7 374 8-19 398 12-7 422 12-19
303 3-8 327 3-20 351 7-8 375 7-20 399 11-8 423 11-20
304 4-8 328 4-20 352 8-8 376 8-20 400 12-8 424 12-20
305 3-9 329 3-21 353 7-9 377 7-21 401 11-9 425 11-21
306 4-9 330 4-21 354 8-9 378 8-21 402 12-9 426 12-21
307 3-10 331 3-22 355 7-10 379 7-22 403 11-10 427 11-22
308 4-10 332 4-22 356 8-10 380 8-22 404 12-10 428 12-22
309 3-11 333 3-23 357 7-11 381 7-23 405 11-11 429 11-23
310 4-11 334 4-23 358 8-11 382 8-23 406 12-11 430 12-23
311 3-12 335 3-24 359 7-12 383 7-24 407 11-12 431 11-24
Spare*1 Spare*1 Spare*1
312 4-12 336 4-24 360 8-12 384 8-24 408 12-12 432 12-24
Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

INST03-11C-410
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-420

Table 3.11.4.4-2 Relation between drives installation order and RAID group number
(3D+1P/2D+2D, SBX) (4/4)
DKU-13 DKU-14 DKU-15
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
433 15-1 457 15-13 481 19-1 505 19-13 529 23-1 553 23-13
434 16-1 458 16-13 482 20-1 506 20-13 530 24-1 554 24-13
435 15-2 459 15-14 483 19-2 507 19-14 531 23-2 555 23-14
436 16-2 460 16-14 484 20-2 508 20-14 532 24-2 556 24-14
437 15-3 461 15-15 485 19-3 509 19-15 533 23-3 557 23-15
438 16-3 462 16-15 486 20-3 510 20-15 534 24-3 558 24-15
439 15-4 463 15-16 487 19-4 511 19-16 535 23-4 559 23-16
440 16-4 464 16-16 488 20-4 512 20-16 536 24-4 560 24-16
441 15-5 465 15-17 489 19-5 513 19-17 537 23-5 561 23-17
442 16-5 466 16-17 490 20-5 514 20-17 538 24-5 562 24-17
443 15-6 467 15-18 491 19-6 515 19-18 539 23-6 563 23-18
444 16-6 468 16-18 492 20-6 516 20-18 540 24-6 564 24-18
445 15-7 469 15-19 493 19-7 517 19-19 541 23-7 565 23-19
446 16-7 470 16-19 494 20-7 518 20-19 542 24-7 566 24-19
447 15-8 471 15-20 495 19-8 519 19-20 543 23-8 567 23-20
448 16-8 472 16-20 496 20-8 520 20-20 544 24-8 568 24-20
449 15-9 473 15-21 497 19-9 521 19-21 545 23-9 569 23-21
450 16-9 474 16-21 498 20-9 522 20-21 546 24-9 570 24-21
451 15-10 475 15-22 499 19-10 523 19-22 547 23-10 571 23-22
452 16-10 476 16-22 500 20-10 524 20-22 548 24-10 572 24-22
453 15-11 477 15-23 501 19-11 525 19-23 549 23-11 573 23-23
454 16-11 478 16-23 502 20-11 526 20-23 550 24-11 574 24-23
455 15-12 479 15-24 503 19-12 527 19-24 551 23-12 575 23-24
Spare*1 Spare*1 Spare*1
456 16-12 480 16-24 504 20-12 528 20-24 552 24-12 576 24-24
Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

INST03-11C-420
 No.
289 290 289 290 289 290 289 290 337 338 337 338 337 338 337 338

DKC
291 292 291 292 291 292 291 292 339 340 339 340 339 340 339 340
Rev.0 / Dec.2013

293 294 293 294 293 294 293 294 341 342 341 342 341 342 341 342

DKU-10
DKU-11
295 296 295 296 295 296 295 296 343 344 343 344 343 344 343 344
Hitachi Proprietary

INST03-11C-430

297 298 297 298 297 298 297 298 345 346 345 346 345 346 345 346

3.11.4.4-2.
299 300 299 300 299 300 299 300 347 348 347 348 347 348 347 348
301 302 301 302 301 302 301 302 349 350 349 350 349 350 349 350
303 304 303 304 303 304 303 304 351 352 351 352 351 352 351 352
added.

305 306 305 306 305 306 305 306 353 354 353 354 353 354 353 354
307 308 307 308 307 308 307 308 355 356 355 356 355 356 355 356
309 310 309 310 309 310 309 310 357 358 357 358 357 358 357 358
311 312 311 312 311 312 311 312 359 360 359 360 359 360 359 360
313 314 313 314 313 314 313 314 361 362 361 362 361 362 361 362
315 316 315 316 315 316 315 316 363 364 363 364 363 364 363 364

Front View
317 318 317 318 317 318 317 318 365 366 365 366 365 366 365 366
319 320 319 320 319 320 319 320 367 368 367 368 367 368 367 368
321 322 321 322 321 322 321 322 369 370 369 370 369 370 369 370
-12
323 324 323 324 323 324 323 324 371 372 371 372 371 372 371 372
325 326 325 326 325 326 325 326 373 374 373 374 373 374 373 374
327 328 327 328 327 328 327 328 375 376 375 376 375 376 375 376
329 330 329 330 329 330 329 330 377 378 377 378 377 378 377 378
-11
2 DKC-F810I-400MCM/800MCM × 4

331 332 331 332 331 332 331 332 379 380 379 380 379 380 379 380
333 334 333 334 333 334 333 334 381 382 381 382 381 382 381 382
335*1 336*1 335*1 336*1 335*1 336*1 335*1 336*1 383*1 384*1 383*1 384*1 383*1 384*1 383*1 384*1
Model Number

-10 -00

001 002 001 002 001 002 001 002 049 050 049 050 049 050 049 050

DKC
003 004 003 004 003 004 003 004 051 052 051 052 051 052 051 052
005 006 005 006 005 006 005 006 053 054 053 054 053 054 053 054

DKU-00
DKU-01
1 DKC-F810I-300KCM/600JCM/900JCM/1R2JCM × 4

007 008 007 008 007 008 007 008 055 056 055 056 055 056 055 056
-01

009 010 009 010 009 010 009 010 057 058 057 058 057 058 057 058
011 012 011 012 011 012 011 012 059 060 059 060 059 060 059 060
013 014 013 014 013 014 013 014 061 062 061 062 061 062 061 062
015 016 015 016 015 016 015 016 063 064 063 064 063 064 063 064
-02

017 018 017 018 017 018 017 018 065 066 065 066 065 066 065 066
RACK RACK RACK RACK RACK RACK

019 020 019 020 019 020 019 020 067 068 067 068 067 068 067 068
021 022 021 022 021 022 021 022 069 070 069 070 069 070 069 070
023 024 023 024 023 024 023 024 071 072 071 072 071 072 071 072
025 026 025 026 025 026 025 026 073 074 073 074 073 074 073 074
027 028 027 028 027 028 027 028 075 076 075 076 075 076 075 076
029 030 029 030 029 030 029 030 077 078 077 078 077 078 077 078

Front View
031 032 031 032 031 032 031 032 079 080 079 080 079 080 079 080
033 034 033 034 033 034 033 034 081 082 081 082 081 082 081 082
035 036 035 036 035 036 035 036 083 084 083 084 083 084 083 084
037 038 037 038 037 038 037 038 085 086 085 086 085 086 085 086
039 040 039 040 039 040 039 040 087 088 087 088 087 088 087 088
041 042 041 042 041 042 041 042 089 090 089 090 089 090 089 090
043 044 043 044 043 044 043 044 091 092 091 092 091 092 091 092
045 046 045 046 045 046 045 046 093 094 093 094 093 094 093 094
047*1 048*1 047*1 048*1 047*1 048*1 047*1 048*1 095*1 096*1 095*1 096*1 095*1 096*1 095*1 096*1
Model Name

SFF SSD Drive

SFF Disk Drive

is to be
installed.
*1: A data or
spare disk
Remarks

The relationship between drives installation order and RAID group number is shown in the Table
Fig. 3.11.4.4-2 (3D+1P/2D+2D) Data Drive/Parity Drive Expansion Sequence (1/3)

INST03-11C-430
Copyright © 2013, Hitachi, Ltd.

(1) Make sure of the location where the RAID group is installed and that where the drive is to be
DKC810I
 385 386 385 386 385 386 385 386 433 434 433 434 433 434 433 434
387 388 387 388 387 388 387 388 435 436 435 436 435 436 435 436
Rev.0 / Dec.2013

389 390 389 390 389 390 389 390 437 438 437 438 437 438 437 438

DKU-12
DKU-13
391 392 391 392 391 392 391 392 439 440 439 440 439 440 439 440
Hitachi Proprietary

INST03-11C-440

393 394 393 394 393 394 393 394 441 442 441 442 441 442 441 442

3.11.4.4-2.
395 396 395 396 395 396 395 396 443 444 443 444 443 444 443 444
397 398 397 398 397 398 397 398 445 446 445 446 445 446 445 446
399 400 399 400 399 400 399 400 447 448 447 448 447 448 447 448
401 402 401 402 401 402 401 402 449 450 449 450 449 450 449 450
403 404 403 404 403 404 403 404 451 452 451 452 451 452 451 452
405 406 405 406 405 406 405 406 453 454 453 454 453 454 453 454
407 408 407 408 407 408 407 408 455 456 455 456 455 456 455 456
409 410 409 410 409 410 409 410 457 458 457 458 457 458 457 458
411 412 411 412 411 412 411 412 459 460 459 460 459 460 459 460

Front View
413 414 413 414 413 414 413 414 461 462 461 462 461 462 461 462
415 416 415 416 415 416 415 416 463 464 463 464 463 464 463 464
417 418 417 418 417 418 417 418 465 466 465 466 465 466 465 466
-12

419 420 419 420 419 420 419 420 467 468 467 468 467 468 467 468
421 422 421 422 421 422 421 422 469 470 469 470 469 470 469 470
423 424 423 424 423 424 423 424 471 472 471 472 471 472 471 472
425 426 425 426 425 426 425 426 473 474 473 474 473 474 473 474
-11

427 428 427 428 427 428 427 428 475 476 475 476 475 476 475 476
429 430 429 430 429 430 429 430 477 478 477 478 477 478 477 478
431*1 432*1 431*1 432*1 431*1 432*1 431*1 432*1 479*1 480*1 479*1 480*1 479*1 480*1 479*1 480*1
-10 -00

097 098 097 098 097 098 097 098 145 146 145 146 145 146 145 146
099 100 099 100 099 100 099 100 147 148 147 148 147 148 147 148
101 102 101 102 101 102 101 102 149 150 149 150 149 150 149 150

DKU-02
DKU-03

103 104 103 104 103 104 103 104 151 152 151 152 151 152 151 152
-01

105 106 105 106 105 106 105 106 153 154 153 154 153 154 153 154
107 108 107 108 107 108 107 108 155 156 155 156 155 156 155 156
109 110 109 110 109 110 109 110 157 158 157 158 157 158 157 158
111 112 111 112 111 112 111 112 159 160 159 160 159 160 159 160
-02

113 114 113 114 113 114 113 114 161 162 161 162 161 162 161 162
RACK RACK RACK RACK RACK RACK

115 116 115 116 115 116 115 116 163 164 163 164 163 164 163 164
117 118 117 118 117 118 117 118 165 166 165 166 165 166 165 166
119 120 119 120 119 120 119 120 167 168 167 168 167 168 167 168
121 122 121 122 121 122 121 122 169 170 169 170 169 170 169 170
123 124 123 124 123 124 123 124 171 172 171 172 171 172 171 172
125 126 125 126 125 126 125 126 173 174 173 174 173 174 173 174

Front View
127 128 127 128 127 128 127 128 175 176 175 176 175 176 175 176
129 130 129 130 129 130 129 130 177 178 177 178 177 178 177 178
131 132 131 132 131 132 131 132 179 180 179 180 179 180 179 180
133 134 133 134 133 134 133 134 181 182 181 182 181 182 181 182
135 136 135 136 135 136 135 136 183 184 183 184 183 184 183 184
137 138 137 138 137 138 137 138 185 186 185 186 185 186 185 186
139 140 139 140 139 140 139 140 187 188 187 188 187 188 187 188
141 142 141 142 141 142 141 142 189 190 189 190 189 190 189 190
143*1 144*1 143*1 144*1 143*1 144*1 143*1 144*1 191*1 192*1 191*1 192*1 191*1 192*1 191*1 192*1

is to be
installed.
*1: A data or
spare disk

The relationship between drives installation order and RAID group number is shown in the Table
Fig. 3.11.4.4-2 (3D+1P/2D+2D) Data Drive/Parity Drive Expansion Sequence (2/3)

INST03-11C-440
Copyright © 2013, Hitachi, Ltd.
DKC810I
 481 482 481 482 481 482 481 482 529 530 529 530 529 530 529 530
483 484 483 484 483 484 483 484 531 532 531 532 531 532 531 532
Rev.0 / Dec.2013

485 486 485 486 485 486 485 486 533 534 533 534 533 534 533 534

DKU-14
DKU-15
487 488 487 488 487 488 487 488 535 536 535 536 535 536 535 536
Hitachi Proprietary

INST03-11C-450

489 490 489 490 489 490 489 490 537 538 537 538 537 538 537 538

3.11.4.4-2.
491 492 491 492 491 492 491 492 539 540 539 540 539 540 539 540
493 494 493 494 493 494 493 494 541 542 541 542 541 542 541 542
495 496 495 496 495 496 495 496 543 544 543 544 543 544 543 544
497 498 497 498 497 498 497 498 545 546 545 546 545 546 545 546
499 500 499 500 499 500 499 500 547 548 547 548 547 548 547 548
501 502 501 502 501 502 501 502 549 550 549 550 549 550 549 550
503 504 503 504 503 504 503 504 551 552 551 552 551 552 551 552
505 506 505 506 505 506 505 506 553 554 553 554 553 554 553 554
507 508 507 508 507 508 507 508 555 556 555 556 555 556 555 556

Front View
509 510 509 510 509 510 509 510 557 558 557 558 557 558 557 558
511 512 511 512 511 512 511 512 559 560 559 560 559 560 559 560
513 514 513 514 513 514 513 514 561 562 561 562 561 562 561 562
-12

515 516 515 516 515 516 515 516 563 564 563 564 563 564 563 564
517 518 517 518 517 518 517 518 565 566 565 566 565 566 565 566
519 520 519 520 519 520 519 520 567 568 567 568 567 568 567 568
521 522 521 522 521 522 521 522 569 570 569 570 569 570 569 570
-11

523 524 523 524 523 524 523 524 571 572 571 572 571 572 571 572
525 526 525 526 525 526 525 526 573 574 573 574 573 574 573 574
527*1 528*1 527*1 528*1 527*1 528*1 527*1 528*1 575*1 576*1 575*1 576*1 575*1 576*1 575*1 576*1
-10 -00

193 194 193 194 193 194 193 194 241 242 241 242 241 242 241 242
195 196 195 196 195 196 195 196 243 244 243 244 243 244 243 244
197 198 197 198 197 198 197 198 245 246 245 246 245 246 245 246

DKU-04
DKU-05

199 200 199 200 199 200 199 200 247 248 247 248 247 248 247 248
-01

201 202 201 202 201 202 201 202 249 250 249 250 249 250 249 250
203 204 203 204 203 204 203 204 251 252 251 252 251 252 251 252
205 206 205 206 205 206 205 206 253 254 253 254 253 254 253 254
207 208 207 208 207 208 207 208 255 256 255 256 255 256 255 256
-02

209 210 209 210 209 210 209 210 257 258 257 258 257 258 257 258
RACK RACK RACK RACK RACK RACK

211 212 211 212 211 212 211 212 259 260 259 260 259 260 259 260
213 214 213 214 213 214 213 214 261 262 261 262 261 262 261 262
215 216 215 216 215 216 215 216 263 264 263 264 263 264 263 264
217 218 217 218 217 218 217 218 265 266 265 266 265 266 265 266
219 220 219 220 219 220 219 220 267 268 267 268 267 268 267 268
221 222 221 222 221 222 221 222 269 270 269 270 269 270 269 270

Front View
223 224 223 224 223 224 223 224 271 272 271 272 271 272 271 272
225 226 225 226 225 226 225 226 273 274 273 274 273 274 273 274
227 228 227 228 227 228 227 228 275 276 275 276 275 276 275 276
229 230 229 230 229 230 229 230 277 278 277 278 277 278 277 278
231 232 231 232 231 232 231 232 279 280 279 280 279 280 279 280
233 234 233 234 233 234 233 234 281 282 281 282 281 282 281 282
235 236 235 236 235 236 235 236 283 284 283 284 283 284 283 284
237 238 237 238 237 238 237 238 285 286 285 286 285 286 285 286
239*1 240*1 239*1 240*1 239*1 240*1 239*1 240*1 287*1 288*1 287*1 288*1 287*1 288*1 287*1 288*1

is to be
installed.
*1: A data or
spare disk

The relationship between drives installation order and RAID group number is shown in the Table
Fig. 3.11.4.4-2 (3D+1P/2D+2D) Data Drive/Parity Drive Expansion Sequence (3/3)

INST03-11C-450
Copyright © 2013, Hitachi, Ltd.
DKC810I
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-460

(iii) RAID5 (3D+1P) / RAID1 (2D+2D), FBX (DKU for FMD)

Relations between the installation locations of the RAID groups and the RAID group
numbers set through the SVP are shown in Table 3.11.4.4-3.

Table 3.11.4.4-3 Relation between drives installation order and RAID group number
(3D+1P/2D+2D, FBX) (1/2)
DKU-00 DKU-01 DKU-02 DKU-03 DKU-04 DKU-05
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
001 1-1 013 5-1 025 9-1 037 13-1 049 17-1 061 21-1
002 1-2 014 5-2 026 9-2 038 13-2 050 17-2 062 21-2
003 1-3 015 5-3 027 9-3 039 13-3 051 17-3 063 21-3
004 1-4 016 5-4 028 9-4 040 13-4 052 17-4 064 21-4
005 1-5 017 5-5 029 9-5 041 13-5 053 17-5 065 21-5
006 1-6 018 5-6 030 9-6 042 13-6 054 17-6 066 21-6
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1
007 2-1 019 6-1 031 10-1 043 14-1 055 18-1 067 22-1
008 2-2 020 6-2 032 10-2 044 14-2 056 18-2 068 22-2
009 2-3 021 6-3 033 10-3 045 14-3 057 18-3 069 22-3
010 2-4 022 6-4 034 10-4 046 14-4 058 18-4 070 22-4
011 2-5 023 6-5 035 10-5 047 14-5 059 18-5 071 22-5
012 2-6 024 6-6 036 10-6 048 14-6 060 18-6 072 22-6
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

Table 3.11.4.4-3 Relation between drives installation order and RAID group number
(3D+1P/2D+2D, FBX) (2/2)
DKU-10 DKU-11 DKU-12 DKU-13 DKU-14 DKU-15
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
073 3-1 085 7-1 097 11-1 109 15-1 121 19-1 133 23-1
074 3-2 086 7-2 098 11-2 110 15-2 122 19-2 134 23-2
075 3-3 087 7-3 099 11-3 111 15-3 123 19-3 135 23-3
076 3-4 088 7-4 100 11-4 112 15-4 124 19-4 136 23-4
077 3-5 089 7-5 101 11-5 113 15-5 125 19-5 137 23-5
078 3-6 090 7-6 102 11-6 114 15-6 126 19-6 138 23-6
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1
079 4-1 091 8-1 103 12-1 115 16-1 127 20-1 139 24-1
080 4-2 092 8-2 104 12-2 116 16-2 128 20-2 140 24-2
081 4-3 093 8-3 105 12-3 117 16-3 129 20-3 141 24-3
082 4-4 094 8-4 106 12-4 118 16-4 130 20-4 142 24-4
083 4-5 095 8-5 107 12-5 119 16-5 131 20-5 143 24-5
084 4-6 096 8-6 108 12-6 120 16-6 132 20-6 144 24-6
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

INST03-11C-460
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-470

(1) Make sure of the location where the RAID group is installed and that where the drive is to be
added.
No. Model Number Model Name Remarks
1 DKC-F810I-1R6FM/3R2FM × 4 Flash Module Drive FMD

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-01
022 023 024*1
019 020 021
016 017 018*1
013 014 015
022 023 024*1
019 020 021
016 017 018*1 DKU-03 DKU-05
013 014 015 070 071 072*1
046 047 048*1
022 023 024*1 043 044 045 067 068 069
019 020 021 040 041 042*1 064 065 066*1
016 017 018*1 037 038 039 061 062 063
013 014 015 046 047 048*1 070 071 072*1
022 023 024*1 043 044 045 067 068 069
019 020 021 040 041 042*1 064 065 066*1
016 017 018*1 037 038 039 061 062 063
013 014 015 046 047 048*1 070 071 072*1
DKU-00 043 044 045 067 068 069
040 041 042*1 064 065 066*1
010 011 012*1 037 038 039 061 062 063
007 008 009 046 047 048*1 070 071 072*1
004 005 006*1 043 044 045 067 068 069
001 002 003 040 041 042*1 064 065 066*1
037 038 039 061 062 063
010 011 012*1
007 008 009 DKU-02 DKU-04
004 005 006*1
001 002 003 034 035 036*1 058 059 060*1
031 032 033 055 056 057
010 011 012*1 028 029 030*1 052 053 054*1
007 008 009 025 026 027 049 050 051
004 005 006*1 034 035 036*1 058 059 060*1
001 002 003 031 032 033 055 056 057
010 011 012*1 028 029 030*1 052 053 054*1
007 008 009 025 026 027 049 050 051
004 005 006*1 034 035 036*1 058 059 060*1
001 002 003 031 032 033 055 056 057
028 029 030*1 052 053 054*1
DKC-0 025 026 027 049 050 051 *1: A data or
034 035 036*1 058 059 060*1
031 032 033 055 056 057 spare disk
028 029 030*1 052 053 054*1 is to be
025 026 027 049 050 051
installed.

Front View

Fig. 3.11.4.4-3 (3D+1P/2D+2D) Data Drive/Parity Drive Expansion Sequence (1/2)

The relationship between drives installation order and RAID group number is shown in the Table
3.11.4.4-3.
INST03-11C-470
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-480

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-11
094 095 096*1
091 092 093
088 089 090*1
085 086 087
094 095 096*1
091 092 093
DKU-15 DKU-13 088 089 090*1
142 143 144*1 118 119 120*1 085 086 087
139 140 141 115 116 117 094 095 096*1
136 137 138*1 112 113 114*1 091 092 093
133 134 135 109 110 111 088 089 090*1
142 143 144*1 118 119 120*1 085 086 087
139 140 141 115 116 117 094 095 096*1
136 137 138*1 112 113 114*1 091 092 093
133 134 135 109 110 111 088 089 090*1
142 143 144*1 118 119 120*1 085 086 087
139 140 141 115 116 117
136 137 138*1 112 113 114*1 DKU-10
133 134 135 109 110 111 082 083 084*1
142 143 144*1 118 119 120*1 079 080 081
139 140 141 115 116 117 076 077 078*1
136 137 138*1 112 113 114*1 073 074 075
133 134 135 109 110 111
082 083 084*1
DKU-14 DKU-12 079 080 081
076 077 078*1
130 131 132*1 106 107 108*1 073 074 075
127 128 129 103 104 105
124 125 126*1 100 101 102*1 082 083 084*1
121 122 123 097 098 099 079 080 081
130 131 132*1 106 107 108*1 076 077 078*1
127 128 129 103 104 105 073 074 075
124 125 126*1 100 101 102*1 082 083 084*1
121 122 123 097 098 099 079 080 081
130 131 132*1 106 107 108*1 076 077 078*1
127 128 129 103 104 105 073 074 075
124 125 126*1 100 101 102*1
121 122 123 097 098 099 DKC-1 *1: A data or
130 131 132*1 106 107 108*1 spare disk
127 128 129 103 104 105
124 125 126*1 100 101 102*1 is to be
121 122 123 097 098 099 installed.

Front View

Fig. 3.11.4.4-3 (3D+1P/2D+2D) Data Drive/Parity Drive Expansion Sequence (2/2)

The relationship between drives installation order and RAID group number is shown in the Table
3.11.4.4-3.

INST03-11C-480
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-490

(iv) RAID5 (7D+1P) / RAID6 (6D+2P), UBX (DKU for 3.5 inch Drive)
Relations between the installation locations of the RAID groups and the RAID group
numbers set through the SVP are shown in Table 3.11.4.4-4.

Table 3.11.4.4-4 Relation between drives installation order and RAID group number
(7D+1P/6D+2P, UBX) (1/2)
DKU-00 DKU-01 DKU-02 DKU-03 DKU-04 DKU-05
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
001 1-1 013 5-1 025 9-1 037 13-1 049 17-1 061 21-1
002 1-2 014 5-2 026 9-2 038 13-2 050 17-2 062 21-2
003 1-3 015 5-3 027 9-3 039 13-3 051 17-3 063 21-3
004 1-4 016 5-4 028 9-4 040 13-4 052 17-4 064 21-4
005 1-5 017 5-5 029 9-5 041 13-5 053 17-5 065 21-5
006 1-6 018 5-6 030 9-6 042 13-6 054 17-6 066 21-6
007 1-7 019 5-7 031 9-7 043 13-7 055 17-7 067 21-7
008 1-8 020 5-8 032 9-8 044 13-8 056 17-8 068 21-8
009 1-9 021 5-9 033 9-9 045 13-9 057 17-9 069 21-9
010 1-10 022 5-10 034 9-10 046 13-10 058 17-10 070 21-10
011 1-11 023 5-11 035 9-11 047 13-11 059 17-11 071 21-11
012 1-12 024 5-12 036 9-12 048 13-12 060 17-12 072 21-12
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

Table 3.11.4.4-4 Relation between drives installation order and RAID group number
(7D+1P/6D+2P, UBX) (2/2)
DKU-10 DKU-11 DKU-12 DKU-13 DKU-14 DKU-15
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
073 3-1 085 7-1 097 11-1 109 15-1 121 19-1 133 23-1
074 3-2 086 7-2 098 11-2 110 15-2 122 19-2 134 23-2
075 3-3 087 7-3 099 11-3 111 15-3 123 19-3 135 23-3
076 3-4 088 7-4 100 11-4 112 15-4 124 19-4 136 23-4
077 3-5 089 7-5 101 11-5 113 15-5 125 19-5 137 23-5
078 3-6 090 7-6 102 11-6 114 15-6 126 19-6 138 23-6
079 3-7 091 7-7 103 11-7 115 15-7 127 19-7 139 23-7
080 3-8 092 7-8 104 11-8 116 15-8 128 19-8 140 23-8
081 3-9 093 7-9 105 11-9 117 15-9 129 19-9 141 23-9
082 3-10 094 7-10 106 11-10 118 15-10 130 19-10 142 23-10
083 3-11 095 7-11 107 11-11 119 15-11 131 19-11 143 23-11
084 3-12 096 7-12 108 11-12 120 15-12 132 19-12 144 23-12
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

INST03-11C-490
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-500

(1) Make sure of the location where the RAID group is installed and that where the drive is to be
added.
No. Model Number Model Name Remarks
1 DKC-F810I-3R0H3M/4R0H3M × 8 LFF Disk Drive

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-11 DKU-01
093 094 095 096*1 021 022 023 024*1
089 090 091 092 017 018 019 020
085 086 087 088 013 014 015 016
093 094 095 096*1 021 022 023 024*1
089 090 091 092 017 018 019 020
085 086 087 088 013 014 015 016
093 094 095 096*1 021 022 023 024*1
089 090 091 092 017 018 019 020
085 086 087 088 013 014 015 016
093 094 095 096*1 021 022 023 024*1
089 090 091 092 017 018 019 020
085 086 087 088 013 014 015 016
093 094 095 096*1 021 022 023 024*1
089 090 091 092 017 018 019 020
085 086 087 088 013 014 015 016
093 094 095 096*1 021 022 023 024*1
089 090 091 092 017 018 019 020
085 086 087 088 013 014 015 016
093 094 095 096*1 021 022 023 024*1
089 090 091 092 017 018 019 020
085 086 087 088 013 014 015 016
093 094 095 096*1 021 022 023 024*1
089 090 091 092 017 018 019 020
085 086 087 088 013 014 015 016
DKU-10 DKU-00
081 082 083 084*1 009 010 011 012*1
077 078 079 080 005 006 007 008
073 074 075 076 001 002 003 004
081 082 083 084*1 009 010 011 012*1
077 078 079 080 005 006 007 008
073 074 075 076 001 002 003 004
081 082 083 084*1 009 010 011 012*1
077 078 079 080 005 006 007 008
073 074 075 076 001 002 003 004
081 082 083 084*1 009 010 011 012*1
077 078 079 080 005 006 007 008
073 074 075 076 001 002 003 004
081 082 083 084*1 009 010 011 012*1
077 078 079 080 005 006 007 008
073 074 075 076 001 002 003 004
081 082 083 084*1 009 010 011 012*1
077 078 079 080 005 006 007 008
073 074 075 076 001 002 003 004
081 082 083 084*1 009 010 011 012*1
077 078 079 080 005 006 007 008
073 074 075 076 001 002 003 004
081 082 083 084*1 009 010 011 012*1
077 078 079 080 005 006 007 008
073 074 075 076 001 002 003 004
*1: A data or
DKC-1 DKC-0 spare disk
is to be
installed.

Front View Front View

Fig. 3.11.4.4-4 (7D+1P/6D+2P) Data Drive/Parity Drive Expansion Sequence (1/3)

The relationship between drives installation order and RAID group number is shown in the Table
3.11.4.4-4.
INST03-11C-500
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-510

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-13 DKU-03
117 118 119 120*1 045 046 047 048*1
113 114 115 116 041 042 043 044
109 110 111 112 037 038 039 040
117 118 119 120*1 045 046 047 048*1
113 114 115 116 041 042 043 044
109 110 111 112 037 038 039 040
117 118 119 120*1 045 046 047 048*1
113 114 115 116 041 042 043 044
109 110 111 112 037 038 039 040
117 118 119 120*1 045 046 047 048*1
113 114 115 116 041 042 043 044
109 110 111 112 037 038 039 040
117 118 119 120*1 045 046 047 048*1
113 114 115 116 041 042 043 044
109 110 111 112 037 038 039 040
117 118 119 120*1 045 046 047 048*1
113 114 115 116 041 042 043 044
109 110 111 112 037 038 039 040
117 118 119 120*1 045 046 047 048*1
113 114 115 116 041 042 043 044
109 110 111 112 037 038 039 040
117 118 119 120*1 045 046 047 048*1
113 114 115 116 041 042 043 044
109 110 111 112 037 038 039 040
DKU-12 DKU-02
105 106 107 108*1 033 034 035 036*1
101 102 103 104 029 030 031 032
097 098 099 100 025 026 027 028
105 106 107 108*1 033 034 035 036*1
101 102 103 104 029 030 031 032
097 098 099 100 025 026 027 028
105 106 107 108*1 033 034 035 036*1
101 102 103 104 029 030 031 032
097 098 099 100 025 026 027 028
105 106 107 108*1 033 034 035 036*1
101 102 103 104 029 030 031 032
097 098 099 100 025 026 027 028
105 106 107 108*1 033 034 035 036*1
101 102 103 104 029 030 031 032
097 098 099 100 025 026 027 028
105 106 107 108*1 033 034 035 036*1
101 102 103 104 029 030 031 032
097 098 099 100 025 026 027 028
105 106 107 108*1 033 034 035 036*1
*1: A data or
101 102 103 104 029 030 031 032 spare disk
097 098 099 100 025 026 027 028
is to be
105 106 107 108*1 033 034 035 036*1
101 102 103 104 029 030 031 032 installed.
097 098 099 100 025 026 027 028

Front View Front View

Fig. 3.11.4.4-4 (7D+1P/6D+2P) Data Drive/Parity Drive Expansion Sequence (2/3)

The relationship between drives installation order and RAID group number is shown in the Table
3.11.4.4-4.

INST03-11C-510
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-520

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-15 DKU-05
141 142 143 144*1 069 070 071 072*1
137 138 139 140 065 066 067 068
133 134 135 136 061 062 063 064
141 142 143 144*1 069 070 071 072*1
137 138 139 140 065 066 067 068
133 134 135 136 061 062 063 064
141 142 143 144*1 069 070 071 072*1
137 138 139 140 065 066 067 068
133 134 135 136 061 062 063 064
141 142 143 144*1 069 070 071 072*1
137 138 139 140 065 066 067 068
133 134 135 136 061 062 063 064
141 142 143 144*1 069 070 071 072*1
137 138 139 140 065 066 067 068
133 134 135 136 061 062 063 064
141 142 143 144*1 069 070 071 072*1
137 138 139 140 065 066 067 068
133 134 135 136 061 062 063 064
141 142 143 144*1 069 070 071 072*1
137 138 139 140 065 066 067 068
133 134 135 136 061 062 063 064
141 142 143 144*1 069 070 071 072*1
137 138 139 140 065 066 067 068
133 134 135 136 061 062 063 064
DKU-14 DKU-04
129 130 131 132*1 057 058 059 060*1
125 126 127 128 053 054 055 056
121 122 123 124 049 050 051 052
129 130 131 132*1 057 058 059 060*1
125 126 127 128 053 054 055 056
121 122 123 124 049 050 051 052
129 130 131 132*1 057 058 059 060*1
125 126 127 128 053 054 055 056
121 122 123 124 049 050 051 052
129 130 131 132*1 057 058 059 060*1
125 126 127 128 053 054 055 056
121 122 123 124 049 050 051 052
129 130 131 132*1 057 058 059 060*1
125 126 127 128 053 054 055 056
121 122 123 124 049 050 051 052
129 130 131 132*1 057 058 059 060*1
125 126 127 128 053 054 055 056
121 122 123 124 049 050 051 052
129 130 131 132*1 057 058 059 060*1
*1: A data or
125 126 127 128 053 054 055 056 spare disk
121 122 123 124 049 050 051 052
is to be
129 130 131 132*1 057 058 059 060*1
125 126 127 128 053 054 055 056 installed.
121 122 123 124 049 050 051 052

Front View Front View

Fig. 3.11.4.4-4 (7D+1P/6D+2P) Data Drive/Parity Drive Expansion Sequence (3/3)

The relationship between drives installation order and RAID group number is shown in the Table
3.11.4.4-4.

INST03-11C-520
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-530

(v) RAID5 (7D+1P) / RAID6 (6D+2P), SBX (DKU for 2.5 inch Drive)
Relations between the installation locations of the RAID groups and the RAID group
numbers set through the SVP are shown in Table 3.11.4.4-5.

Table 3.11.4.4-5 Relation between drives installation order and RAID group number
(7D+1P/6D+2P, SBX) (1/2)
DKU-00 DKU-01 DKU-02 DKU-03 DKU-04 DKU-05
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
001 1-1 025 5-1 049 9-1 073 13-1 097 17-1 121 19-1
002 1-2 026 5-2 050 9-2 074 13-2 098 17-2 122 19-2
003 1-3 027 5-3 051 9-3 075 13-3 099 17-3 123 19-3
004 1-4 028 5-4 052 9-4 076 13-4 100 17-4 124 19-4
005 1-5 029 5-5 053 9-5 077 13-5 101 17-5 125 19-5
006 1-6 030 5-6 054 9-6 078 13-6 102 17-6 126 19-6
007 1-7 031 5-7 055 9-7 079 13-7 103 17-7 127 19-7
008 1-8 032 5-8 056 9-8 080 13-8 104 17-8 128 19-8
009 1-9 033 5-9 057 9-9 081 13-9 105 17-9 129 19-9
010 1-10 034 5-10 058 9-10 082 13-10 106 17-10 130 19-10
011 1-11 035 5-11 059 9-11 083 13-11 107 17-11 131 19-11
012 1-12 036 5-12 060 9-12 084 13-12 108 17-12 132 19-12
013 1-13 037 5-13 061 9-13 085 13-13 109 17-13 133 19-13
014 1-14 038 5-14 062 9-14 086 13-14 110 17-14 134 19-14
015 1-15 039 5-15 063 9-15 087 13-15 111 17-15 135 19-15
016 1-16 040 5-16 064 9-16 088 13-16 112 17-16 136 19-16
017 1-17 041 5-17 065 9-17 089 13-17 113 17-17 137 19-17
018 1-18 042 5-18 066 9-18 090 13-18 114 17-18 138 19-18
019 1-19 043 5-19 067 9-19 091 13-19 115 17-19 139 19-19
020 1-20 044 5-20 068 9-20 092 13-20 116 17-20 140 19-20
021 1-21 045 5-21 069 9-21 093 13-21 117 17-21 141 19-21
022 1-22 046 5-22 070 9-22 094 13-22 118 17-22 142 19-22
023 1-23 047 5-23 071 9-23 095 13-23 119 17-23 143 19-23
024 1-24 048 5-24 072 9-24 096 13-24 120 17-24 144 19-24
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

INST03-11C-530
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-540

Table 3.11.4.4-5 Relation between drives installation order and RAID group number
(7D+1P/6D+2P, SBX) (2/2)
DKU-10 DKU-11 DKU-12 DKU-13 DKU-14 DKU-15
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
145 3-1 169 7-1 193 11-1 217 15-1 241 19-1 265 23-1
146 3-2 170 7-2 194 11-2 218 15-2 242 19-2 266 23-2
147 3-3 171 7-3 195 11-3 219 15-3 243 19-3 267 23-3
148 3-4 172 7-4 196 11-4 220 15-4 244 19-4 268 23-4
149 3-5 173 7-5 197 11-5 221 15-5 245 19-5 269 23-5
150 3-6 174 7-6 198 11-6 222 15-6 246 19-6 270 23-6
151 3-7 175 7-7 199 11-7 223 15-7 247 19-7 271 23-7
152 3-8 176 7-8 200 11-8 224 15-8 248 19-8 272 23-8
153 3-9 177 7-9 201 11-9 225 15-9 249 19-9 273 23-9
154 3-10 178 7-10 202 11-10 226 15-10 250 19-10 274 23-10
155 3-11 179 7-11 203 11-11 227 15-11 251 19-11 275 23-11
156 3-12 180 7-12 204 11-12 228 15-12 252 19-12 276 23-12
157 3-13 181 7-13 205 11-13 229 15-13 253 19-13 277 23-13
158 3-14 182 7-14 206 11-14 230 15-14 254 19-14 278 23-14
159 3-15 183 7-15 207 11-15 231 15-15 255 19-15 279 23-15
160 3-16 184 7-16 208 11-16 232 15-16 256 19-16 280 23-16
161 3-17 185 7-17 209 11-17 233 15-17 257 19-17 281 23-17
162 3-18 186 7-18 210 11-18 234 15-18 258 19-18 282 23-18
163 3-19 187 7-19 211 11-19 235 15-19 259 19-19 283 23-19
164 3-20 188 7-20 212 11-20 236 15-20 260 19-20 284 23-20
165 3-21 189 7-21 213 11-21 237 15-21 261 19-21 285 23-21
166 3-22 190 7-22 214 11-22 238 15-22 262 19-22 286 23-22
167 3-23 191 7-23 215 11-23 239 15-23 263 19-23 287 23-23
168 3-24 192 7-24 216 11-24 240 15-24 264 19-24 288 23-24
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

INST03-11C-540
 No.
145 145 145 145 145 145 145 145 169 169 169 169 169 169 169 169

DKC
146 146 146 146 146 146 146 146 170 170 170 170 170 170 170 170
Rev.0 / Dec.2013

147 147 147 147 147 147 147 147 171 171 171 171 171 171 171 171

DKU-10
DKU-11
148 148 148 148 148 148 148 148 172 172 172 172 172 172 172 172
Hitachi Proprietary

INST03-11C-550

149 149 149 149 149 149 149 149 173 173 173 173 173 173 173 173

3.11.4.4-5.
150 150 150 150 150 150 150 150 174 174 174 174 174 174 174 174
151 151 151 151 151 151 151 151 175 175 175 175 175 175 175 175
152 152 152 152 152 152 152 152 176 176 176 176 176 176 176 176
added.

153 153 153 153 153 153 153 153 177 177 177 177 177 177 177 177
154 154 154 154 154 154 154 154 178 178 178 178 178 178 178 178
155 155 155 155 155 155 155 155 179 179 179 179 179 179 179 179
156 156 156 156 156 156 156 156 180 180 180 180 180 180 180 180
157 157 157 157 157 157 157 157 181 181 181 181 181 181 181 181
158 158 158 158 158 158 158 158 182 182 182 182 182 182 182 182

Front View
159 159 159 159 159 159 159 159 183 183 183 183 183 183 183 183
160 160 160 160 160 160 160 160 184 184 184 184 184 184 184 184
161 161 161 161 161 161 161 161 185 185 185 185 185 185 185 185
-12
162 162 162 162 162 162 162 162 186 186 186 186 186 186 186 186
163 163 163 163 163 163 163 163 187 187 187 187 187 187 187 187
164 164 164 164 164 164 164 164 188 188 188 188 188 188 188 188
165 165 165 165 165 165 165 165 189 189 189 189 189 189 189 189
-11
2 DKC-F810I-400MCM/800MCM × 8

166 166 166 166 166 166 166 166 190 190 190 190 190 190 190 190
167 167 167 167 167 167 167 167 191 191 191 191 191 191 191 191
168*1 168*1 168*1 168*1 168*1 168*1 168*1 168*1 192*1 192*1 192*1 192*1 192*1 192*1 192*1 192*1
Model Number

-10 -00

001 001 001 001 001 001 001 001 025 025 025 025 025 025 025 025

DKC
002 002 002 002 002 002 002 002 026 026 026 026 026 026 026 026
003 003 003 003 003 003 003 003 027 027 027 027 027 027 027 027

DKU-00
DKU-01
1 DKC-F810I-300KCM/600JCM/900JCM/1R2JCM × 8

004 004 004 004 004 004 004 004 028 028 028 028 028 028 028 028
-01

005 005 005 005 005 005 005 005 029 029 029 029 029 029 029 029
006 006 006 006 006 006 006 006 030 030 030 030 030 030 030 030
007 007 007 007 007 007 007 007 031 031 031 031 031 031 031 031
008 008 008 008 008 008 008 008 032 032 032 032 032 032 032 032
-02

009 009 009 009 009 009 009 009 033 033 033 033 033 033 033 033
RACK RACK RACK RACK RACK RACK

010 010 010 010 010 010 010 010 034 034 034 034 034 034 034 034
011 011 011 011 011 011 011 011 035 035 035 035 035 035 035 035
012 012 012 012 012 012 012 012 036 036 036 036 036 036 036 036
013 013 013 013 013 013 013 013 037 037 037 037 037 037 037 037
014 014 014 014 014 014 014 014 038 038 038 038 038 038 038 038
015 015 015 015 015 015 015 015 039 039 039 039 039 039 039 039

Front View
016 016 016 016 016 016 016 016 040 040 040 040 040 040 040 040
017 017 017 017 017 017 017 017 041 041 041 041 041 041 041 041
018 018 018 018 018 018 018 018 042 042 042 042 042 042 042 042
019 019 019 019 019 019 019 019 043 043 043 043 043 043 043 043
020 020 020 020 020 020 020 020 044 044 044 044 044 044 044 044
021 021 021 021 021 021 021 021 045 045 045 045 045 045 045 045
022 022 022 022 022 022 022 022 046 046 046 046 046 046 046 046
023 023 023 023 023 023 023 023 047 047 047 047 047 047 047 047
024*1 024*1 024*1 024*1 024*1 024*1 024*1 024*1 048*1 048*1 048*1 048*1 048*1 048*1 048*1 048*1
Model Name

SFF SSD Drive

SFF Disk Drive

is to be
installed.
*1: A data or
spare disk
Remarks

The relationship between drives installation order and RAID group number is shown in the Table
Fig. 3.11.4.4-5 (7D+1P/6D+2P) Data Drive/Parity Drive Expansion Sequence (1/3)

INST03-11C-550
Copyright © 2013, Hitachi, Ltd.

(1) Make sure of the location where the RAID group is installed and that where the drive is to be
DKC810I
 193 193 193 193 193 193 193 193 217 217 217 217 217 217 217 217
194 194 194 194 194 194 194 194 218 218 218 218 218 218 218 218
Rev.0 / Dec.2013

195 195 195 195 195 195 195 195 219 219 219 219 219 219 219 219

DKU-12
DKU-13
196 196 196 196 196 196 196 196 220 220 220 220 220 220 220 220
Hitachi Proprietary

INST03-11C-560

197 197 197 197 197 197 197 197 221 221 221 221 221 221 221 221

3.11.4.4-5.
198 198 198 198 198 198 198 198 222 222 222 222 222 222 222 222
199 199 199 199 199 199 199 199 223 223 223 223 223 223 223 223
200 200 200 200 200 200 200 200 224 224 224 224 224 224 224 224
201 201 201 201 201 201 201 201 225 225 225 225 225 225 225 225
202 202 202 202 202 202 202 202 226 226 226 226 226 226 226 226
203 203 203 203 203 203 203 203 227 227 227 227 227 227 227 227
204 204 204 204 204 204 204 204 228 228 228 228 228 228 228 228
205 205 205 205 205 205 205 205 229 229 229 229 229 229 229 229
206 206 206 206 206 206 206 206 230 230 230 230 230 230 230 230

Front View
207 207 207 207 207 207 207 207 231 231 231 231 231 231 231 231
208 208 208 208 208 208 208 208 232 232 232 232 232 232 232 232
209 209 209 209 209 209 209 209 233 233 233 233 233 233 233 233
-12

210 210 210 210 210 210 210 210 234 234 234 234 234 234 234 234
211 211 211 211 211 211 211 211 235 235 235 235 235 235 235 235
212 212 212 212 212 212 212 212 236 236 236 236 236 236 236 236
213 213 213 213 213 213 213 213 237 237 237 237 237 237 237 237
-11

214 214 214 214 214 214 214 214 238 238 238 238 238 238 238 238
215 215 215 215 215 215 215 215 239 239 239 239 239 239 239 239
216*1 216*1 216*1 216*1 216*1 216*1 216*1 216*1 240*1 240*1 240*1 240*1 240*1 240*1 240*1 240*1
-10 -00

049 049 049 049 049 049 049 049 073 073 073 073 073 073 073 073
050 050 050 050 050 050 050 050 074 074 074 074 074 074 074 074
051 051 051 051 051 051 051 051 075 075 075 075 075 075 075 075

DKU-02
DKU-03

052 052 052 052 052 052 052 052 076 076 076 076 076 076 076 076
-01

053 053 053 053 053 053 053 053 077 077 077 077 077 077 077 077
054 054 054 054 054 054 054 054 078 078 078 078 078 078 078 078
055 055 055 055 055 055 055 055 079 079 079 079 079 079 079 079
056 056 056 056 056 056 056 056 080 080 080 080 080 080 080 080
-02

057 057 057 057 057 057 057 057 081 081 081 081 081 081 081 081
RACK RACK RACK RACK RACK RACK

058 058 058 058 058 058 058 058 082 082 082 082 082 082 082 082
059 059 059 059 059 059 059 059 083 083 083 083 083 083 083 083
060 060 060 060 060 060 060 060 084 084 084 084 084 084 084 084
061 061 061 061 061 061 061 061 085 085 085 085 085 085 085 085
062 062 062 062 062 062 062 062 086 086 086 086 086 086 086 086
063 063 063 063 063 063 063 063 087 087 087 087 087 087 087 087

Front View
064 064 064 064 064 064 064 064 088 088 088 088 088 088 088 088
065 065 065 065 065 065 065 065 089 089 089 089 089 089 089 089
066 066 066 066 066 066 066 066 090 090 090 090 090 090 090 090
067 067 067 067 067 067 067 067 091 091 091 091 091 091 091 091
068 068 068 068 068 068 068 068 092 092 092 092 092 092 092 092
069 069 069 069 069 069 069 069 093 093 093 093 093 093 093 093
070 070 070 070 070 070 070 070 094 094 094 094 094 094 094 094
071 071 071 071 071 071 071 071 095 095 095 095 095 095 095 095
072*1 072*1 072*1 072*1 072*1 072*1 072*1 072*1 096*1 096*1 096*1 096*1 096*1 096*1 096*1 096*1

is to be
installed.
*1: A data or
spare disk

The relationship between drives installation order and RAID group number is shown in the Table
Fig. 3.11.4.4-5 (7D+1P/6D+2P) Data Drive/Parity Drive Expansion Sequence (2/3)

INST03-11C-560
Copyright © 2013, Hitachi, Ltd.
DKC810I
 241 241 241 241 241 241 241 241 265 265 265 265 265 265 265 265
242 242 242 242 242 242 242 242 266 266 266 266 266 266 266 266
Rev.0 / Dec.2013

243 243 243 243 243 243 243 243 267 267 267 267 267 267 267 267

DKU-14
DKU-15
244 244 244 244 244 244 244 244 268 268 268 268 268 268 268 268
Hitachi Proprietary

INST03-11C-570

245 245 245 245 245 245 245 245 269 269 269 269 269 269 269 269

3.11.4.4-5.
246 246 246 246 246 246 246 246 270 270 270 270 270 270 270 270
247 247 247 247 247 247 247 247 271 271 271 271 271 271 271 271
248 248 248 248 248 248 248 248 272 272 272 272 272 272 272 272
249 249 249 249 249 249 249 249 273 273 273 273 273 273 273 273
250 250 250 250 250 250 250 250 274 274 274 274 274 274 274 274
251 251 251 251 251 251 251 251 275 275 275 275 275 275 275 275
252 252 252 252 252 252 252 252 276 276 276 276 276 276 276 276
253 253 253 253 253 253 253 253 277 277 277 277 277 277 277 277
254 254 254 254 254 254 254 254 278 278 278 278 278 278 278 278

Front View
255 255 255 255 255 255 255 255 279 279 279 279 279 279 279 279
256 256 256 256 256 256 256 256 280 280 280 280 280 280 280 280
257 257 257 257 257 257 257 257 281 281 281 281 281 281 281 281
-12

258 258 258 258 258 258 258 258 282 282 282 282 282 282 282 282
259 259 259 259 259 259 259 259 283 283 283 283 283 283 283 283
260 260 260 260 260 260 260 260 284 284 284 284 284 284 284 284
261 261 261 261 261 261 261 261 285 285 285 285 285 285 285 285
-11

262 262 262 262 262 262 262 262 286 286 286 286 286 286 286 286
263 263 263 263 263 263 263 263 287 287 287 287 287 287 287 287
264*1 264*1 264*1 264*1 264*1 264*1 264*1 264*1 288*1 288*1 288*1 288*1 288*1 288*1 288*1 288*1
-10 -00

097 097 097 097 097 097 097 097 121 121 121 121 121 121 121 121
098 098 098 098 098 098 098 098 122 122 122 122 122 122 122 122
099 099 099 099 099 099 099 099 123 123 123 123 123 123 123 123

DKU-04
DKU-05

100 100 100 100 100 100 100 100 124 124 124 124 124 124 124 124
-01

101 101 101 101 101 101 101 101 125 125 125 125 125 125 125 125
102 102 102 102 102 102 102 102 126 126 126 126 126 126 126 126
103 103 103 103 103 103 103 103 127 127 127 127 127 127 127 127
104 104 104 104 104 104 104 104 128 128 128 128 128 128 128 128
-02

105 105 105 105 105 105 105 105 129 129 129 129 129 129 129 129
RACK RACK RACK RACK RACK RACK

106 106 106 106 106 106 106 106 130 130 130 130 130 130 130 130
107 107 107 107 107 107 107 107 131 131 131 131 131 131 131 131
108 108 108 108 108 108 108 108 132 132 132 132 132 132 132 132
109 109 109 109 109 109 109 109 133 133 133 133 133 133 133 133
110 110 110 110 110 110 110 110 134 134 134 134 134 134 134 134
111 111 111 111 111 111 111 111 135 135 135 135 135 135 135 135

Front View
112 112 112 112 112 112 112 112 136 136 136 136 136 136 136 136
113 113 113 113 113 113 113 113 137 137 137 137 137 137 137 137
114 114 114 114 114 114 114 114 138 138 138 138 138 138 138 138
115 115 115 115 115 115 115 115 139 139 139 139 139 139 139 139
116 116 116 116 116 116 116 116 140 140 140 140 140 140 140 140
117 117 117 117 117 117 117 117 141 141 141 141 141 141 141 141
118 118 118 118 118 118 118 118 142 142 142 142 142 142 142 142
119 119 119 119 119 119 119 119 143 143 143 143 143 143 143 143
120*1 120*1 120*1 120*1 120*1 120*1 120*1 120*1 144*1 144*1 144*1 144*1 144*1 144*1 144*1 144*1

is to be
installed.
*1: A data or
spare disk

The relationship between drives installation order and RAID group number is shown in the Table
Fig. 3.11.4.4-5 (7D+1P/6D+2P) Data Drive/Parity Drive Expansion Sequence (3/3)

INST03-11C-570
Copyright © 2013, Hitachi, Ltd.
DKC810I
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-580

(vi) RAID5 (7D+1P) / RAID6 (6D+2P), FBX (DKU for FMD)

Relations between the installation locations of the RAID groups and the RAID group
numbers set through the SVP are shown in Table 3.11.4.4-6.

Table 3.11.4.4-6 Relation between drives installation order and RAID group number
(7D+1P/6D+2P, FBX) (1/2)
DKU-00 DKU-01 DKU-02 DKU-03 DKU-04 DKU-05
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
001 1-1 007 5-1 013 9-1 019 13-1 025 17-1 031 21-1
002 1-2 008 5-2 014 9-2 020 13-2 026 17-2 032 21-2
003 1-3 009 5-3 015 9-3 021 13-3 027 17-3 033 21-3
004 1-4 010 5-4 016 9-4 022 13-4 028 17-4 034 21-4
005 1-5 011 5-5 017 9-5 023 13-5 029 17-5 035 21-5
006 1-6 012 5-6 018 9-6 024 13-6 030 17-6 036 21-6
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

Table 3.11.4.4-6 Relation between drives installation order and RAID group number
(7D+1P/6D+2P, FBX) (2/2)
DKU-06 DKU-07 DKU-10 DKU-11 DKU-12 DKU-13
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
037 3-1 043 7-1 049 11-1 055 15-1 061 19-1 067 23-1
038 3-2 044 7-2 050 11-2 056 15-2 062 19-2 068 23-2
039 3-3 045 7-3 051 11-3 057 15-3 063 19-3 069 23-3
040 3-4 046 7-4 052 11-4 058 15-4 064 19-4 070 23-4
041 3-5 047 7-5 053 11-5 059 15-5 065 19-5 071 23-5
042 3-6 048 7-6 054 11-6 060 15-6 066 19-6 072 23-6
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

INST03-11C-580
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-590

(1) Make sure of the location where the RAID group is installed and that where the drive is to be
added.
No. Model Number Model Name Remarks
1 DKC-F810I-1R6FM/3R2FM × 8 Flash Module Drive FMD

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-01
010 011 012*1
007 008 009
010 011 012*1
007 008 009
010 011 012*1
007 008 009
010 011 012*1 DKU-03 DKU-05
007 008 009 034 035 036*1
022 023 024*1
010 011 012*1 019 020 021 031 032 033
007 008 009 022 023 024*1 034 035 036*1
010 011 012*1 019 020 021 031 032 033
007 008 009 034 035 036*1
022 023 024*1
010 011 012*1 019 020 021 031 032 033
007 008 009 022 023 024*1 034 035 036*1
010 011 012*1 019 020 021 031 032 033
007 008 009 034 035 036*1
022 023 024*1
DKU-00 019 020 021 031 032 033
022 023 024*1 034 035 036*1
004 005 006*1 019 020 021 031 032 033
001 002 003 022 023 024*1 034 035 036*1
004 005 006*1 019 020 021 031 032 033
001 002 003 022 023 024*1 034 035 036*1
019 020 021 031 032 033
004 005 006*1
001 002 003 DKU-02 DKU-04
004 005 006*1
001 002 003 016 017 018*1 028 029 030*1
013 014 015 025 026 027
004 005 006*1 016 017 018*1 028 029 030*1
001 002 003 013 014 015 025 026 027
004 005 006*1 016 017 018*1 028 029 030*1
001 002 003 013 014 015 025 026 027
004 005 006*1 016 017 018*1 028 029 030*1
001 002 003 013 014 015 025 026 027
004 005 006*1 016 017 018*1 028 029 030*1
001 002 003 013 014 015 025 026 027
016 017 018*1 028 029 030*1 *1: A data or
DKC-0 013 014 015 025 026 027
016 017 018*1 028 029 030*1 spare disk
013 014 015 025 026 027 is to be
016 017 018*1 028 029 030*1
013 014 015 025 026 027 installed.

Front View

Fig. 3.11.4.4-6 (7D+1P/6D+2P) Data Drive/Parity Drive Expansion Sequence (1/2)

The relationship between drives installation order and RAID group number is shown in the Table
3.11.4.4-6.
INST03-11C-590
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-600

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-11
046 047 048*1
043 044 045
046 047 048*1
043 044 045
046 047 048*1
DKU-13 043 044 045
DKU-15 046 047 048*1
070 071 072*1 058 059 060*1 043 044 045
067 068 069 055 056 057 046 047 048*1
070 071 072*1 058 059 060*1 043 044 045
067 068 069 055 056 057 046 047 048*1
070 071 072*1 058 059 060*1 043 044 045
067 068 069 055 056 057 046 047 048*1
070 071 072*1 058 059 060*1 043 044 045
067 068 069 055 056 057 046 047 048*1
070 071 072*1 058 059 060*1 043 044 045
067 068 069 055 056 057
070 071 072*1 058 059 060*1 DKU-10
067 068 069 055 056 057 040 041 042*1
070 071 072*1 058 059 060*1 037 038 039
067 068 069 055 056 057 040 041 042*1
070 071 072*1 058 059 060*1 037 038 039
067 068 069 055 056 057
040 041 042*1
DKU-14 DKU-12 037 038 039
040 041 042*1
064 065 066*1 052 053 054*1 037 038 039
061 062 063 049 050 051
064 065 066*1 052 053 054*1 040 041 042*1
061 062 063 049 050 051 037 038 039
064 065 066*1 052 053 054*1 040 041 042*1
061 062 063 049 050 051 037 038 039
064 065 066*1 052 053 054*1 040 041 042*1
061 062 063 049 050 051 037 038 039
064 065 066*1 052 053 054*1 040 041 042*1
061 062 063 049 050 051 037 038 039 *1: A data or
064 065 066*1 052 053 054*1
061 062 063 049 050 051 DKC-1 spare disk
064 065 066*1 052 053 054*1
061 062 063 049 050 051 is to be
064 065 066*1 052 053 054*1 installed.
061 062 063 049 050 051

Front View

Fig. 3.11.4.4-6 (7D+1P/6D+2P) Data Drive/Parity Drive Expansion Sequence (2/2)

The relationship between drives installation order and RAID group number is shown in the Table
3.11.4.4-6.

INST03-11C-600
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-610

(vii) RAID6 (14D+2P), UBX (DKU for 3.5 inch Drive)

Relations between the installation locations of the RAID groups and the RAID group
numbers set through the SVP are shown in Table 3.11.4.4-7.

Table 3.11.4.4-7 Relation between drives installation order and RAID group number
(14D+2P, UBX) (1/2)
DKU-00 DKU-01 DKU-02 DKU-03 DKU-04 DKU-05
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
001 1-1 007 5-1 013 9-1 019 13-1 025 17-1 031 21-1
002 1-3 008 5-3 014 9-3 020 13-3 026 17-3 032 21-3
003 1-5 009 5-5 015 9-5 021 13-5 027 17-5 033 21-5
004 1-7 010 5-7 016 9-7 022 13-7 028 17-7 034 21-7
005 1-9 011 5-9 017 9-9 023 13-9 029 17-9 035 21-9
06 1-11 012 5-11 018 9-11 024 13-1 030 17-11 036 21-11
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

Table 3.11.4.4-7 Relation between drives installation order and RAID group number
(14D+2P, UBX) (2/2)
DKU-10 DKU-11 DKU-12 DKU-13 DKU-14 DKU-15
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
037 3-1 043 7-1 049 11-1 055 15-1 061 19-1 067 23-1
038 3-3 044 7-3 050 11-3 056 15-3 062 19-3 068 23-3
039 3-5 045 7-5 051 11-5 057 15-5 063 19-5 069 23-5
040 3-7 046 7-7 052 11-7 058 15-7 064 19-7 070 23-7
041 3-9 047 7-9 053 11-9 059 15-9 065 19-9 071 23-9
Spare*1
042 3-11 048 7-11 054 11-11 060 15-11 066 1-11 072 23-11
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

INST03-11C-610
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-620

(1) Make sure of the location where the RAID group is installed and that where the drive is to be
added.
No. Model Number Model Name Remarks
1 DKC-F810I-3R0H3M/4R0H3M × 16 LFF Disk Drive

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-11 DKU-01
047 047 048 048*1 011 011 012 012*1
045 045 046 046 009 009 010 010
043 043 044 044 007 007 008 008
047 047 048 048*1 011 011 012 012*1
045 045 046 046 009 009 010 010
043 043 044 044 007 007 008 008
047 047 048 048*1 011 011 012 012*1
045 045 046 046 009 009 010 010
043 043 044 044 007 007 008 008
047 047 048 048*1 011 011 012 012*1
045 045 046 046 009 009 010 010
043 043 044 044 007 007 008 008
047 047 048 048*1 011 011 012 012*1
045 045 046 046 009 009 010 010
043 043 044 044 007 007 008 008
047 047 048 048*1 011 011 012 012*1
045 045 046 046 009 009 010 010
043 043 044 044 007 007 008 008
047 047 048 048*1 011 011 012 012*1
045 045 046 046 009 009 010 010
043 043 044 044 007 007 008 008
047 047 048 048*1 011 011 012 012*1
045 045 046 046 009 009 010 010
043 043 044 044 007 007 008 008
DKU-10 DKU-00
041 041 042 042*1 005 005 006 006*1
039 039 040 040 003 003 004 004
037 037 038 038 001 001 002 002
041 041 042 042*1 005 005 006 006*1
039 039 040 040 003 003 004 004
037 037 038 038 001 001 002 002
041 041 042 042*1 005 005 006 006*1
039 039 040 040 003 003 004 004
037 037 038 038 001 001 002 002
041 041 042 042*1 005 005 006 006*1
039 039 040 040 003 003 004 004
037 037 038 038 001 001 002 002
041 041 042 042*1 005 005 006 006*1
039 039 040 040 003 003 004 004
037 037 038 038 001 001 002 002
041 041 042 042*1 005 005 006 006*1
039 039 040 040 003 003 004 004
037 037 038 038 001 001 002 002
041 041 042 042*1 005 005 006 006*1
039 039 040 040 003 003 004 004
037 037 038 038 001 001 002 002
041 041 042 042*1 005 005 006 006*1
039 039 040 040 003 003 004 004
037 037 038 038 001 001 002 002
*1: A data or
DKC-1 DKC-0 spare disk
is to be
installed.

Front View Front View

Fig. 3.11.4.4-7 (14D+2P) Data Drive/Parity Drive Expansion Sequence (1/3)

The relationship between drives installation order and RAID group number is shown in the Table
3.11.4.4-7.
INST03-11C-620
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-630

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-13 DKU-03
059 059 060 060*1 023 023 024 024*1
057 057 058 058 021 021 022 022
055 055 056 056 019 019 020 020
059 059 060 060*1 023 023 024 024*1
057 057 058 058 021 021 022 022
055 055 056 056 019 019 020 020
059 059 060 060*1 023 023 024 024*1
057 057 058 058 021 021 022 022
055 055 056 056 019 019 020 020
059 059 060 060*1 023 023 024 024*1
057 057 058 058 021 021 022 022
055 055 056 056 019 019 020 020
059 059 060 060*1 023 023 024 024*1
057 057 058 058 021 021 022 022
055 055 056 056 019 019 020 020
059 059 060 060*1 023 023 024 024*1
057 057 058 058 021 021 022 022
055 055 056 056 019 019 020 020
059 059 060 060*1 023 023 024 024*1
057 057 058 058 021 021 022 022
055 055 056 056 019 019 020 020
059 059 060 060*1 023 023 024 024*1
057 057 058 058 021 021 022 022
055 055 056 056 019 019 020 020
DKU-12 DKU-02
053 053 054 054*1 017 017 018 018*1
051 051 052 052 015 015 016 016
049 049 050 050 013 013 014 014
053 053 054 054*1 017 017 018 018*1
051 051 052 052 015 015 016 016
049 049 050 050 013 013 014 014
053 053 054 054*1 017 017 018 018*1
051 051 052 052 015 015 016 016
049 049 050 050 013 013 014 014
053 053 054 054*1 017 017 018 018*1
051 051 052 052 015 015 016 016
049 049 050 050 013 013 014 014
053 053 054 054*1 017 017 018 018*1
051 051 052 052 015 015 016 016
049 049 050 050 013 013 014 014
053 053 054 054*1 017 017 018 018*1
051 051 052 052 015 015 016 016
049 049 050 050 013 013 014 014
053 053 054 054*1 017 017 018 018*1
*1: A data or
051 051 052 052 015 015 016 016 spare disk
049 049 050 050 013 013 014 014
is to be
053 053 054 054*1 017 017 018 018*1
051 051 052 052 015 015 016 016 installed.
049 049 050 050 013 013 014 014

Front View Front View

Fig. 3.11.4.4-7 (14D+2P) Data Drive/Parity Drive Expansion Sequence (2/3)

The relationship between drives installation order and RAID group number is shown in the Table
3.11.4.4-7.

INST03-11C-630
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-640

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-15 DKU-05
071 071 072 072*1 035 035 036 036*1
069 069 070 070 033 033 034 034
067 067 068 068 031 031 032 032
071 071 072 072*1 035 035 036 036*1
069 069 070 070 033 033 034 034
067 067 068 068 031 031 032 032
071 071 072 072*1 035 035 036 036*1
069 069 070 070 033 033 034 034
067 067 068 068 031 031 032 032
071 071 072 072*1 035 035 036 036*1
069 069 070 070 033 033 034 034
067 067 068 068 031 031 032 032
071 071 072 072*1 035 035 036 036*1
069 069 070 070 033 033 034 034
067 067 068 068 031 031 032 032
071 071 072 072*1 035 035 036 036*1
069 069 070 070 033 033 034 034
067 067 068 068 031 031 032 032
071 071 072 072*1 035 035 036 036*1
069 069 070 070 033 033 034 034
067 067 068 068 031 031 032 032
071 071 072 072*1 035 035 036 036*1
069 069 070 070 033 033 034 034
067 067 068 068 031 031 032 032
DKU-14 DKU-04
065 065 066 066*1 029 029 030 030*1
063 063 064 064 027 027 028 028
061 061 062 062 025 025 026 026
065 065 066 066*1 029 029 030 030*1
063 063 064 064 027 027 028 028
061 061 062 062 025 025 026 026
065 065 066 066*1 029 029 030 030*1
063 063 064 064 027 027 028 028
061 061 062 062 025 025 026 026
065 065 066 066*1 029 029 030 030*1
063 063 064 064 027 027 028 028
061 061 062 062 025 025 026 026
065 065 066 066*1 029 029 030 030*1
063 063 064 064 027 027 028 028
061 061 062 062 025 025 026 026
065 065 066 066*1 029 029 030 030*1
063 063 064 064 027 027 028 028
061 061 062 062 025 025 026 026
065 065 066 066*1 029 029 030 030*1
*1: A data or
063 063 064 064 027 027 028 028 spare disk
061 061 062 062 025 025 026 026
is to be
065 065 066 066*1 029 029 030 030*1
063 063 064 064 027 027 028 028 installed.
061 061 062 062 025 025 026 026

Front View Front View

Fig. 3.11.4.4-7 (14D+2P) Data Drive/Parity Drive Expansion Sequence (3/3)

The relationship between drives installation order and RAID group number is shown in the Table
3.11.4.4-7.

INST03-11C-640
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-650

(viii) RAID6 (14D+2P), SBX (DKU for 2.5 inch Drive)

Relations between the installation locations of the RAID groups and the RAID group
numbers set through the SVP are shown in Table 3.11.4.4-8.

Table 3.11.4.4-8 Relation between drives installation order and RAID group number
(14D+2P, SBX) (1/2)
DKU-00 DKU-01 DKU-02 DKU-03 DKU-04 DKU-05
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
001 1-1 013 5-1 025 9-1 037 13-1 049 17-1 061 21-1
002 1-3 014 5-3 026 9-3 038 13-3 050 17-3 062 21-3
003 1-5 015 5-5 027 9-5 039 13-5 051 17-5 063 21-5
004 1-7 016 5-7 028 9-7 040 13-7 052 17-7 064 21-7
005 1-9 017 5-9 029 9-9 041 13-9 053 17-9 065 21-9
006 1-11 018 5-11 030 9-11 042 13-11 054 17-11 066 21-11
007 1-13 019 5-13 031 9-13 043 13-13 055 17-13 067 21-13
008 1-15 020 5-15 032 9-15 044 13-15 056 17-15 068 21-15
009 1-17 021 5-17 033 9-17 045 13-17 057 17-17 069 21-17
010 1-19 022 5-19 034 9-19 046 13-19 058 17-19 070 21-19
011 1-21 023 5-21 035 9-21 047 13-21 059 17-21 071 21-21
012 1-23 024 5-23 036 9-23 048 13-23 060 17-23 072 21-23
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

Table 3.11.4.4-8 Relation between drives installation order and RAID group number
(14D+2P, SBX) (2/2)
DKU-10 DKU-11 DKU-12 DKU-13 DKU-14 DKU-15
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
073 3-1 085 7-1 097 11-1 109 15-1 121 19-1 133 23-1
074 3-3 086 7-3 098 11-3 110 15-3 122 19-3 134 23-3
075 3-5 087 7-5 099 11-5 111 15-5 123 19-5 135 23-5
076 3-7 088 7-7 100 11-7 112 15-7 124 19-7 136 23-7
077 3-9 089 7-9 101 11-9 113 15-9 125 19-9 137 23-9
078 3-11 090 7-11 102 11-11 114 15-11 126 19-11 138 23-11
079 3-13 091 7-13 103 11-13 115 15-13 127 19-13 139 23-13
080 3-15 092 7-15 104 11-15 116 15-15 128 19-15 140 23-15
081 3-17 093 7-17 105 11-17 117 15-17 129 19-17 141 23-17
082 3-19 094 7-19 106 11-19 118 15-19 130 19-19 142 23-19
083 3-21 095 7-21 107 11-21 119 15-21 131 19-21 143 23-21
084 3-23 096 7-23 108 11-23 120 15-23 132 19-23 144 23-23
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

INST03-11C-650
 No.
073 073 073 073 073 073 073 073 085 085 085 085 085 085 085 085

DKC
073 073 073 073 073 073 073 073 085 085 085 085 085 085 085 085
Rev.0 / Dec.2013

074 074 074 074 074 074 074 074 086 086 086 086 086 086 086 086

DKU-10
DKU-11
074 074 074 074 074 074 074 074 086 086 086 086 086 086 086 086
Hitachi Proprietary

INST03-11C-660

075 075 075 075 075 075 075 075 087 087 087 087 087 087 087 087

3.11.4.4-8.
075 075 075 075 075 075 075 075 087 087 087 087 087 087 087 087
076 076 076 076 076 076 076 076 088 088 088 088 088 088 088 088
076 076 076 076 076 076 076 076 088 088 088 088 088 088 088 088
added.

077 077 077 077 077 077 077 077 089 089 089 089 089 089 089 089
077 077 077 077 077 077 077 077 089 089 089 089 089 089 089 089
078 078 078 078 078 078 078 078 090 090 090 090 090 090 090 090
078 078 078 078 078 078 078 078 090 090 090 090 090 090 090 090
079 079 079 079 079 079 079 079 091 091 091 091 091 091 091 091
079 079 079 079 079 079 079 079 091 091 091 091 091 091 091 091

Front View
080 080 080 080 080 080 080 080 092 092 092 092 092 092 092 092
080 080 080 080 080 080 080 080 092 092 092 092 092 092 092 092
081 081 081 081 081 081 081 081 093 093 093 093 093 093 093 093
-12
081 081 081 081 081 081 081 081 093 093 093 093 093 093 093 093
082 082 082 082 082 082 082 082 094 094 094 094 094 094 094 094
082 082 082 082 082 082 082 082 094 094 094 094 094 094 094 094
083 083 083 083 083 083 083 083 095 095 095 095 095 095 095 095
-11
2 DKC-F810I-400MCM/800MCM × 1

083 083 083 083 083 083 083 083 095 095 095 095 095 095 095 095
084 084 084 084 084 084 084 084 096 096 096 096 096 096 096 096
084*1 084*1 084*1 084*1 084*1 084*1 084*1 084*1 096*1 096*1 096*1 096*1 096*1 096*1 096*1 096*1
Model Number

-10 -00

001 001 001 001 001 001 001 001 013 013 013 013 013 013 013 013

DKC
001 001 001 001 001 001 001 001 013 013 013 013 013 013 013 013
002 002 002 002 002 002 002 002 014 014 014 014 014 014 014 014

DKU-00
DKU-01
1 DKC-F810I-300KCM/600JCM/900JCM/1R2JCM × 1

002 002 002 002 002 002 002 002 014 014 014 014 014 014 014 014
-01

003 003 003 003 003 003 003 003 015 015 015 015 015 015 015 015
003 003 003 003 003 003 003 003 015 015 015 015 015 015 015 015
004 004 004 004 004 004 004 004 016 016 016 016 016 016 016 016
004 004 004 004 004 004 004 004 016 016 016 016 016 016 016 016
-02

005 005 005 005 005 005 005 005 017 017 017 017 017 017 017 017
RACK RACK RACK RACK RACK RACK

005 005 005 005 005 005 005 005 017 017 017 017 017 017 017 017
006 006 006 006 006 006 006 006 018 018 018 018 018 018 018 018
006 006 006 006 006 006 006 006 018 018 018 018 018 018 018 018
007 007 007 007 007 007 007 007 019 019 019 019 019 019 019 019
007 007 007 007 007 007 007 007 019 019 019 019 019 019 019 019
008 008 008 008 008 008 008 008 020 020 020 020 020 020 020 020

Front View
008 008 008 008 008 008 008 008 020 020 020 020 020 020 020 020
009 009 009 009 009 009 009 009 021 021 021 021 021 021 021 021
009 009 009 009 009 009 009 009 021 021 021 021 021 021 021 021
010 010 010 010 010 010 010 010 022 022 022 022 022 022 022 022
010 010 010 010 010 010 010 010 022 022 022 022 022 022 022 022
011 011 011 011 011 011 011 011 023 023 023 023 023 023 023 023
011 011 011 011 011 011 011 011 023 023 023 023 023 023 023 023
012 012 012 012 012 012 012 012 024 024 024 024 024 024 024 024
012*1 012*1 012*1 012*1 012*1 012*1 012*1 012*1 024*1 024*1 024*1 024*1 024*1 024*1 024*1 024*1
Model Name

SFF SSD Drive

SFF Disk Drive

is to be

Fig. 3.11.4.4-8 (14D+2P) Data Drive/Parity Drive Expansion Sequence (1/3)

installed.
*1: A data or
spare disk
Remarks

The relationship between drives installation order and RAID group number is shown in the Table

INST03-11C-660
Copyright © 2013, Hitachi, Ltd.

(1) Make sure of the location where the RAID group is installed and that where the drive is to be
DKC810I
 097 097 097 097 097 097 097 097 109 109 109 109 109 109 109 109
097 097 097 097 097 097 097 097 109 109 109 109 109 109 109 109
Rev.0 / Dec.2013

098 098 098 098 098 098 098 098 110 110 110 110 110 110 110 110

DKU-12
DKU-13
098 098 098 098 098 098 098 098 110 110 110 110 110 110 110 110
Hitachi Proprietary

INST03-11C-670

099 099 099 099 099 099 099 099 111 111 111 111 111 111 111 111

3.11.4.4-8.
099 099 099 099 099 099 099 099 111 111 111 111 111 111 111 111
100 100 100 100 100 100 100 100 112 112 112 112 112 112 112 112
100 100 100 100 100 100 100 100 112 112 112 112 112 112 112 112
101 101 101 101 101 101 101 101 113 113 113 113 113 113 113 113
101 101 101 101 101 101 101 101 113 113 113 113 113 113 113 113
102 102 102 102 102 102 102 102 114 114 114 114 114 114 114 114
102 102 102 102 102 102 102 102 114 114 114 114 114 114 114 114
103 103 103 103 103 103 103 103 115 115 115 115 115 115 115 115
103 103 103 103 103 103 103 103 115 115 115 115 115 115 115 115

Front View
104 104 104 104 104 104 104 104 116 116 116 116 116 116 116 116
104 104 104 104 104 104 104 104 116 116 116 116 116 116 116 116
105 105 105 105 105 105 105 105 117 117 117 117 117 117 117 117
-12

105 105 105 105 105 105 105 105 117 117 117 117 117 117 117 117
106 106 106 106 106 106 106 106 118 118 118 118 118 118 118 118
106 106 106 106 106 106 106 106 118 118 118 118 118 118 118 118
107 107 107 107 107 107 107 107 119 119 119 119 119 119 119 119
-11

107 107 107 107 107 107 107 107 119 119 119 119 119 119 119 119
108 108 108 108 108 108 108 108 120 120 120 120 120 120 120 120
108*1 108*1 108*1 108*1 108*1 108*1 108*1 108*1 120*1 120*1 120*1 120*1 120*1 120*1 120*1 120*1
-10 -00

025 025 025 025 025 025 025 025 037 037 037 037 037 037 037 037
025 025 025 025 025 025 025 025 037 037 037 037 037 037 037 037
026 026 026 026 026 026 026 026 038 038 038 038 038 038 038 038

DKU-02
DKU-03

026 026 026 026 026 026 026 026 038 038 038 038 038 038 038 038
-01

027 027 027 027 027 027 027 027 039 039 039 039 039 039 039 039
027 027 027 027 027 027 027 027 039 039 039 039 039 039 039 039
028 028 028 028 028 028 028 028 040 040 040 040 040 040 040 040
028 028 028 028 028 028 028 028 040 040 040 040 040 040 040 040
-02

029 029 029 029 029 029 029 029 041 041 041 041 041 041 041 041
RACK RACK RACK RACK RACK RACK

029 029 029 029 029 029 029 029 041 041 041 041 041 041 041 041
030 030 030 030 030 030 030 030 042 042 042 042 042 042 042 042
030 030 030 030 030 030 030 030 042 042 042 042 042 042 042 042
031 031 031 031 031 031 031 031 043 043 043 043 043 043 043 043
031 031 031 031 031 031 031 031 043 043 043 043 043 043 043 043
032 032 032 032 032 032 032 032 044 044 044 044 044 044 044 044

Front View
032 032 032 032 032 032 032 032 044 044 044 044 044 044 044 044
033 033 033 033 033 033 033 033 045 045 045 045 045 045 045 045
033 033 033 033 033 033 033 033 045 045 045 045 045 045 045 045
034 034 034 034 034 034 034 034 046 046 046 046 046 046 046 046
034 034 034 034 034 034 034 034 046 046 046 046 046 046 046 046
035 035 035 035 035 035 035 035 047 047 047 047 047 047 047 047
035 035 035 035 035 035 035 035 047 047 047 047 047 047 047 047
036 036 036 036 036 036 036 036 048 048 048 048 048 048 048 048
036*1 036*1 036*1 036*1 036*1 036*1 036*1 036*1 048*1 048*1 048*1 048*1 048*1 048*1 048*1 048*1

is to be

Fig. 3.11.4.4-8 (14D+2P) Data Drive/Parity Drive Expansion Sequence (2/3)

installed.
*1: A data or
spare disk

The relationship between drives installation order and RAID group number is shown in the Table

INST03-11C-670
Copyright © 2013, Hitachi, Ltd.
DKC810I
 121 121 121 121 121 121 121 121 133 133 133 133 133 133 133 133
121 121 121 121 121 121 121 121 133 133 133 133 133 133 133 133
Rev.0 / Dec.2013

122 122 122 122 122 122 122 122 134 134 134 134 134 134 134 134

DKU-14
DKU-15
122 122 122 122 122 122 122 122 134 134 134 134 134 134 134 134
Hitachi Proprietary

INST03-11C-680

123 123 123 123 123 123 123 123 135 135 135 135 135 135 135 135

3.11.4.4-8.
123 123 123 123 123 123 123 123 135 135 135 135 135 135 135 135
124 124 124 124 124 124 124 124 136 136 136 136 136 136 136 136
124 124 124 124 124 124 124 124 136 136 136 136 136 136 136 136
125 125 125 125 125 125 125 125 137 137 137 137 137 137 137 137
125 125 125 125 125 125 125 125 137 137 137 137 137 137 137 137
126 126 126 126 126 126 126 126 138 138 138 138 138 138 138 138
126 126 126 126 126 126 126 126 138 138 138 138 138 138 138 138
127 127 127 127 127 127 127 127 139 139 139 139 139 139 139 139
127 127 127 127 127 127 127 127 139 139 139 139 139 139 139 139

Front View
128 128 128 128 128 128 128 128 140 140 140 140 140 140 140 140
128 128 128 128 128 128 128 128 140 140 140 140 140 140 140 140
129 129 129 129 129 129 129 129 141 141 141 141 141 141 141 141
-12

129 129 129 129 129 129 129 129 141 141 141 141 141 141 141 141
130 130 130 130 130 130 130 130 142 142 142 142 142 142 142 142
130 130 130 130 130 130 130 130 142 142 142 142 142 142 142 142
131 131 131 131 131 131 131 131 143 143 143 143 143 143 143 143
-11

131 131 131 131 131 131 131 131 143 143 143 143 143 143 143 143
132 132 132 132 132 132 132 132 144 144 144 144 144 144 144 144
132*1 132*1 132*1 132*1 132*1 132*1 132*1 132*1 144*1 144*1 144*1 144*1 144*1 144*1 144*1 144*1
-10 -00

049 049 049 049 049 049 049 049 061 061 061 061 061 061 061 061
049 049 049 049 049 049 049 049 061 061 061 061 061 061 061 061
050 050 050 050 050 050 050 050 062 062 062 062 062 062 062 062

DKU-04
DKU-05
-01

050 050 050 050 050 050 050 050 062 062 062 062 062 062 062 062
051 051 051 051 051 051 051 051 063 063 063 063 063 063 063 063
051 051 051 051 051 051 051 051 063 063 063 063 063 063 063 063
052 052 052 052 052 052 052 052 064 064 064 064 064 064 064 064
-02

052 052 052 052 052 052 052 052 064 064 064 064 064 064 064 064
RACK RACK RACK RACK RACK RACK

053 053 053 053 053 053 053 053 065 065 065 065 065 065 065 065
053 053 053 053 053 053 053 053 065 065 065 065 065 065 065 065
054 054 054 054 054 054 054 054 066 066 066 066 066 066 066 066
054 054 054 054 054 054 054 054 066 066 066 066 066 066 066 066
055 055 055 055 055 055 055 055 067 067 067 067 067 067 067 067
055 055 055 055 055 055 055 055 067 067 067 067 067 067 067 067
056 056 056 056 056 056 056 056 068 068 068 068 068 068 068 068

Front View
056 056 056 056 056 056 056 056 068 068 068 068 068 068 068 068
057 057 057 057 057 057 057 057 069 069 069 069 069 069 069 069
057 057 057 057 057 057 057 057 069 069 069 069 069 069 069 069
058 058 058 058 058 058 058 058 070 070 070 070 070 070 070 070
058 058 058 058 058 058 058 058 070 070 070 070 070 070 070 070
059 059 059 059 059 059 059 059 071 071 071 071 071 071 071 071
059 059 059 059 059 059 059 059 071 071 071 071 071 071 071 071
060 060 060 060 060 060 060 060 072 072 072 072 072 072 072 072
060*1 060*1 060*1 060*1 060*1 060*1 060*1 060*1 072*1 072*1 072*1 072*1 072*1 072*1 072*1 072*1

Fig. 3.11.4.4-8 (14D+2P) Data Drive/Parity Drive Expansion Sequence (3/3)

is to be
installed.
*1: A data or
spare disk

The relationship between drives installation order and RAID group number is shown in the Table

INST03-11C-680
Copyright © 2013, Hitachi, Ltd.
DKC810I
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-690

(ix) RAID6 (14D+2P), FBX (DKU for FMD)

Relations between the installation locations of the RAID groups and the RAID group
numbers set through the SVP are shown in Table 3.11.4.4-9.

Table 3.11.4.4-9 Relation between drives installation order and RAID group number
(14D+2P, FBX) (1/2)
DKU-00 DKU-01 DKU-02 DKU-03 DKU-04 DKU-05
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
001 1-1 004 5-1 007 9-1 010 13-1 013 17-1 016 21-1
002 1-3 005 5-3 008 9-3 011 13-3 014 17-3 017 21-3
003 1-5 006 5-5 009 9-5 012 13-5 015 17-5 018 21-5
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

Table 3.11.4.4-9 Relation between drives installation order and RAID group number
(14D+2P, FBX) (2/2)
DKU-10 DKU-11 DKU-12 DKU-13 DKU-14 DKU-15
Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID Installation RAID
Order Group Order Group Order Group Order Group Order Group Order Group
No. No. No. No. No. No.
019 3-1 022 7-1 025 11-1 028 15-1 031 19-1 034 23-1
020 3-3 023 7-3 026 11-3 029 15-3 032 19-3 035 23-3
021 3-5 024 7-5 027 11-5 030 15-5 033 19-5 036 23-5
Spare*1 Spare*1 Spare*1 Spare*1 Spare*1 Spare*1

*1: A data or spare drive is to be installed.

INST03-11C-690
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-700

(1) Make sure of the location where the RAID group is installed and that where the drive is to be
added.
No. Model Number Model Name Remarks
1 DKC-F810I-1R6FM/3R2FM × 16 Flash Module Drive FMD

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-01
005 006 006*1
004 004 005
005 006 006*1
004 004 005
005 006 006*1
004 004 005 DKU-03 DKU-05
005 006 006*1
004 004 005 011 012 012*1 017 018 018*1
005 006 006*1 010 010 011 016 016 017
004 004 005 011 012 012*1 017 018 018*1
005 006 006*1 010 010 011 016 016 017
004 004 005 011 012 012*1 017 018 018*1
005 006 006*1 010 010 011 016 016 017
004 004 005 011 012 012*1 017 018 018*1
005 006 006*1 010 010 011 016 016 017
004 004 005 011 012 012*1 017 018 018*1
010 010 011 016 016 017
DKU-00 011 012 012*1 017 018 018*1
010 010 011 016 016 017
012 003 003*1
001 001 002 011 012 012*1 017 018 018*1
002 003 003*1 010 010 011 016 016 017
011 012 012*1 017 018 018*1
001 001 002 010 010 011 016 016 017
012 003 003*1
001 001 002 DKU-02 DKU-04
002 003 003*1
001 001 002 008 009 009*1 014 015 015*1
007 007 008 013 013 014
012 003 003*1 008 009 009*1 014 015 015*1
001 001 002 007 007 008 013 013 014
002 003 003*1 008 009 009*1 014 015 015*1
001 001 002 007 007 008 013 013 014
012 003 003*1 008 009 009*1 014 015 015*1
001 001 002 007 007 008 013 013 014
002 003 003*1 008 009 009*1 014 015 015*1
001 001 002 007 007 008 013 013 014
008 009 009*1 014 015 015*1
DKC-0 007 007 008 013 013 014 *1: A data or
008 009 009*1 014 015 015*1 spare disk
007 007 008 013 013 014
008 009 009*1 014 015 015*1 is to be
007 007 008 013 013 014
installed.

Front View

Fig. 3.11.4.4-9 (14D+2P) Data Drive/Parity Drive Expansion Sequence (1/2)

The relationship between drives installation order and RAID group number is shown in the Table
3.11.4.4-9.
INST03-11C-700
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-710

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-11
023 024 024*1
022 022 023
023 024 024*1
022 022 023
023 024 024*1
022 022 023
DKU-15 DKU-13 023 024 024*1
035 036 036*1 029 030 030*1 022 022 023
034 034 035 028 028 029 023 024 024*1
035 036 036*1 029 030 030*1 022 022 023
034 034 035 028 028 029 023 024 024*1
035 036 036*1 029 030 030*1 022 022 023
034 034 035 028 028 029 023 024 024*1
035 036 036*1 029 030 030*1 022 022 023
034 034 035 028 028 029 023 024 024*1
035 036 036*1 029 030 030*1 022 022 023
034 034 035 028 028 029
035 036 036*1 029 030 030*1 DKU-10
034 034 035 028 028 029 020 021 021*1
035 036 036*1 029 030 030*1 019 019 020
034 034 035 028 028 029 020 021 021*1
035 036 036*1 029 030 030*1 019 019 020
034 034 035 028 028 029
020 021 021*1
DKU-14 DKU-12 019 019 020
020 021 021*1
032 033 033*1 026 027 027*1 019 019 020
031 031 032 025 025 026
032 033 033*1 026 027 027*1 020 021 021*1
031 031 032 025 025 026 019 019 020
032 033 033*1 026 027 027*1 020 021 021*1
031 031 032 025 025 026 019 019 020
032 033 033*1 026 027 027*1 020 021 021*1
031 031 032 025 025 026 019 019 020
032 033 033*1 026 027 027*1 020 021 021*1
031 031 032 025 025 026 019 019 020
032 033 033*1 026 027 027*1
031 031 032 025 025 026 DKC-1 *1: A data or
032 033 033*1 026 027 027*1
031 031 032 025 025 026 spare disk
032 033 033*1 026 027 027*1 is to be
031 031 032 025 025 026
installed.

Front View

Fig. 3.11.4.4-9 (14D+2P) Data Drive/Parity Drive Expansion Sequence (2/2)

The relationship between drives installation order and RAID group number is shown in the Table
3.11.4.4-9.

INST03-11C-710
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-720

(x) Spare Drive, UBX (DKU for 3.5 inch Drive)

Table 3.11.4.4-10 Relation between Drive installation order and Spare Drive number
(1/4)
DKU-00 DKU-01 DKU-02 DKU-03
Installation B4 Spare Installation B4 Spare Installation B4 Spare Installation B4 Spare
Order No. drive No. Order No. drive No. Order No. drive No. Order No. drive No.
001 1st Spare1 009 2nd Spare1 017 5th Spare1 025 6th Spare1
002 1st Spare2 010 2nd Spare2 018 5th Spare2 026 6th Spare2
003 1st Spare3 011 2nd Spare3 019 5th Spare3 027 6th Spare3
004 1st Spare4 012 2nd Spare4 020 5th Spare4 028 6th Spare4
005 1st Spare5 013 2nd Spare5 021 5th Spare5 029 6th Spare5
006 1st Spare6 014 2nd Spare6 022 5th Spare6 030 6th Spare6
007 1st Spare7 015 2nd Spare7 023 5th Spare7 031 6th Spare7
008 1st Spare8 016 2nd Spare8 024 5th Spare8 032 6th Spare8

Table 3.11.4.4-10 Relation between Drive installation order and Spare Drive number
(2/4)
DKU-04 DKU-05
Installation B4 Spare Installation B4 Spare
Order No. drive No. Order No. drive No.
033 9th Spare1 041 10st Spare1
034 9th Spare2 042 10st Spare2
035 9th Spare3 043 10st Spare3
036 9th Spare4 044 10st Spare4
037 9th Spare5 045 10st Spare5
038 9th Spare6 046 10st Spare6
039 9th Spare7 047 10st Spare7
040 9th Spare8 048 10st Spare8

INST03-11C-720
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-730

Table 3.11.4.4-10 Relation between Drive installation order and Spare Drive number
(3/4)
DKU-10 DKU-11 DKU-12 DKU-13
Installation B4 Spare Installation B4 Spare Installation B4 Spare Installation B4 Spare
Order No. drive No. Order No. drive No. Order No. drive No. Order No. drive No.
049 3rd Spare1 057 4th Spare1 065 7th Spare1 073 8th Spare1
050 3rd Spare2 058 4th Spare2 066 7th Spare2 074 8th Spare2
051 3rd Spare3 059 4th Spare3 067 7th Spare3 075 8th Spare3
052 3rd Spare4 060 4th Spare4 068 7th Spare4 076 8th Spare4
053 3rd Spare5 061 4th Spare5 069 7th Spare5 077 8th Spare5
054 3rd Spare6 062 4th Spare6 070 7th Spare6 078 8th Spare6
055 3rd Spare7 063 4th Spare7 071 7th Spare7 079 8th Spare7
056 3rd Spare8 064 4th Spare8 072 7th Spare8 080 8th Spare8

Table 3.11.4.4-10 Relation between Drive installation order and Spare Drive number
(4/4)
DKU-14 DKU-15
Installation B4 Spare Installation B4 Spare
Order No. drive No. Order No. drive No.
081 11th Spare1 089 12th Spare1
082 11th Spare2 090 12th Spare2
083 11th Spare3 091 12th Spare3
084 11th Spare4 092 12th Spare4
085 11th Spare5 093 12th Spare5
086 11th Spare6 094 12th Spare6
087 11th Spare7 095 12th Spare7
088 11th Spare8 096 12th Spare8

INST03-11C-730
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-740

No. Model Number Model Name Data and Parity

1 DKC-F810I-3R0H3M/4R0H3M × 1 LFF Disk Drive Spare drive

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-11 DKU-01
064 016

063 015

062 014

061 013

060 012

059 011

058 010

057 009

DKU-10 DKU-00
056 008

055 007

054 006

053 005

052 004

051
003

050 002

049 001

*1: A data or
DKC-1 DKC-0 spare disk
is to be
installed.

Front View Front View

Fig. 3.11.4.4-10 Spare Drive Expansion Sequence (1/3)

INST03-11C-740
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-750

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-13 DKU-03
080 032

079 031

078 030

077 029

076 028

075 027

074 026

073 025

DKU-12 DKU-02
072 024

071 023

070 022

069 021

068 020

067 019

066 018
*1: A data or
spare disk
is to be
065 017
installed.

Front View Front View

Fig. 3.11.4.4-10 Spare Drive Expansion Sequence (2/3)

INST03-11C-750
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-760

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-15 DKU-05
096 048

095 047

094 046

093 045

092 044

091 043

090 042

089 041

DKU-14 DKU-04
088 040

087 039

086 038

085 037

084 036

083 035

082 034
*1: A data or
spare disk
is to be
081 033
installed.

Front View Front View

Fig. 3.11.4.4-10 Spare Drive Expansion Sequence (3/3)

INST03-11C-760
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-770

(xi) Spare Drive, SBX (DKU for 2.5 inch Drive)

Table 3.11.4.4-11 Relation between Drive installation order and Spare Drive number
(1/4)
DKU-00 DKU-01 DKU-02 DKU-03
Installation B4 Spare Installation B4 Spare Installation B4 Spare Installation B4 Spare
Order No. drive No. Order No. drive No. Order No. drive No. Order No. drive No.
001 1st Spare1 009 2nd Spare1 017 5th Spare1 025 6th Spare1
002 1st Spare2 010 2nd Spare2 018 5th Spare2 026 6th Spare2
003 1st Spare3 011 2nd Spare3 019 5th Spare3 027 6th Spare3
004 1st Spare4 012 2nd Spare4 020 5th Spare4 028 6th Spare4
005 1st Spare5 013 2nd Spare5 021 5th Spare5 029 6th Spare5
006 1st Spare6 014 2nd Spare6 022 5th Spare6 030 6th Spare6
007 1st Spare7 015 2nd Spare7 023 5th Spare7 031 6th Spare7
008 1st Spare8 016 2nd Spare8 024 5th Spare8 032 6th Spare8

Table 3.11.4.4-11 Relation between Drive installation order and Spare Drive number
(2/4)
DKU-04 DKU-05
Installation B4 Spare Installation B4 Spare
Order No. drive No. Order No. drive No.
033 9th Spare1 041 10st Spare1
034 9th Spare2 042 10st Spare2
035 9th Spare3 043 10st Spare3
036 9th Spare4 044 10st Spare4
037 9th Spare5 045 10st Spare5
038 9th Spare6 046 10st Spare6
039 9th Spare7 047 10st Spare7
040 9th Spare8 048 10st Spare8

INST03-11C-770
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-780

Table 3.11.4.4-11 Relation between Drive installation order and Spare Drive number
(3/4)
DKU-10 DKU-11 DKU-12 DKU-13
Installation B4 Spare Installation B4 Spare Installation B4 Spare Installation B4 Spare
Order No. drive No. Order No. drive No. Order No. drive No. Order No. drive No.
049 3rd Spare1 057 4th Spare1 065 7th Spare1 073 8th Spare1
050 3rd Spare2 058 4th Spare2 066 7th Spare2 074 8th Spare2
051 3rd Spare3 059 4th Spare3 067 7th Spare3 075 8th Spare3
052 3rd Spare4 060 4th Spare4 068 7th Spare4 076 8th Spare4
053 3rd Spare5 061 4th Spare5 069 7th Spare5 077 8th Spare5
054 3rd Spare6 062 4th Spare6 070 7th Spare6 078 8th Spare6
055 3rd Spare7 063 4th Spare7 071 7th Spare7 079 8th Spare7
056 3rd Spare8 064 4th Spare8 072 7th Spare8 080 8th Spare8

Table 3.11.4.4-11 Relation between Drive installation order and Spare Drive number
(4/4)
DKU-14 DKU-15
Installation B4 Spare Installation B4 Spare
Order No. drive No. Order No. drive No.
081 11th Spare1 089 12th Spare1
082 11th Spare2 090 12th Spare2
083 11th Spare3 091 12th Spare3
084 11th Spare4 092 12th Spare4
085 11th Spare5 093 12th Spare5
086 11th Spare6 094 12th Spare6
087 11th Spare7 095 12th Spare7
088 11th Spare8 096 12th Spare8

INST03-11C-780
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-790

No. Model Number Model Name Remarks

1 DKC-F810I-300KCM/600JCM/900JCM/1R2JCM × 1 SFF Disk Drive Spare Drive
2 DKC-F810I-400MCM/800MCM × 1 SFF SSD Drive Spare Drive

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-11 DKU-01
064

016
063

015
062

014
061

013
060

012
059

011
058

010
057

009
DKU-10 DKU-00
056

008
055

007
054

006
053

005
052

004
051

003
050

002
049

001

*1: A data or
DKC-1 DKC-0 spare disk
is to be
installed.

Front View Front View

Fig. 3.11.4.4-11 Spare Drive Expansion Sequence (1/3)

INST03-11C-790
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-800

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-13 DKU-03

080

032
079

031
078

030
077

029
076

028
075

027
074

026
073

025
DKU-12 DKU-02
072

024
071

023
070

022
069

021
068

020
067

019

*1: A data or
066

018

spare disk
is to be
065

017

installed.

Front View Front View

Fig. 3.11.4.4-11 Spare Drive Expansion Sequence (2/3)

INST03-11C-800
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-810

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-15 DKU-05

096

048
095

047
094

046
093

045
092

044
091

043
090

042
089

041
DKU-14 DKU-04
088

040
087

039
086

038
085

037
084

036
083

035

*1: A data or
082

034

spare disk
is to be
081

033

installed.

Front View Front View

Fig. 3.11.4.4-11 Spare Drive Expansion Sequence (3/3)

INST03-11C-810
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-820

(xii) Spare Drive, FBX (DKU for FMD)

Table 3.11.4.4-12 Relation between Drive installation order and Spare Drive number
(1/4)
DKU-00 DKU-01 DKU-02 DKU-03
Installation B4 Spare Installation B4 Spare Installation B4 Spare Installation B4 Spare
Order No. drive No. Order No. drive No. Order No. drive No. Order No. drive No.
001 1st Spare1 009 2nd Spare1 017 5th Spare1 025 6th Spare1
002 1st Spare2 010 2nd Spare2 018 5th Spare2 026 6th Spare2
003 1st Spare3 011 2nd Spare3 019 5th Spare3 027 6th Spare3
004 1st Spare4 012 2nd Spare4 020 5th Spare4 028 6th Spare4
005 1st Spare5 013 2nd Spare5 021 5th Spare5 029 6th Spare5
006 1st Spare6 014 2nd Spare6 022 5th Spare6 030 6th Spare6
007 1st Spare7 015 2nd Spare7 023 5th Spare7 031 6th Spare7
008 1st Spare8 016 2nd Spare8 024 5th Spare8 032 6th Spare8

Table 3.11.4.4-12 Relation between Drive installation order and Spare Drive number
(2/4)
DKU-04 DKU-05
Installation B4 Spare Installation B4 Spare
Order No. drive No. Order No. drive No.
033 9th Spare1 041 10st Spare1
034 9th Spare2 042 10st Spare2
035 9th Spare3 043 10st Spare3
036 9th Spare4 044 10st Spare4
037 9th Spare5 045 10st Spare5
038 9th Spare6 046 10st Spare6
039 9th Spare7 047 10st Spare7
040 9th Spare8 048 10st Spare8

INST03-11C-820
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-830

Table 3.11.4.4-12 Relation between Drive installation order and Spare Drive number
(3/4)
DKU-10 DKU-11 DKU-12 DKU-13
Installation B4 Spare Installation B4 Spare Installation B4 Spare Installation B4 Spare
Order No. drive No. Order No. drive No. Order No. drive No. Order No. drive No.
049 3rd Spare1 057 4th Spare1 065 7th Spare1 073 8th Spare1
050 3rd Spare2 058 4th Spare2 066 7th Spare2 074 8th Spare2
051 3rd Spare3 059 4th Spare3 067 7th Spare3 075 8th Spare3
052 3rd Spare4 060 4th Spare4 068 7th Spare4 076 8th Spare4
053 3rd Spare5 061 4th Spare5 069 7th Spare5 077 8th Spare5
054 3rd Spare6 062 4th Spare6 070 7th Spare6 078 8th Spare6
055 3rd Spare7 063 4th Spare7 071 7th Spare7 079 8th Spare7
056 3rd Spare8 064 4th Spare8 072 7th Spare8 080 8th Spare8

Table 3.11.4.4-12 Relation between Drive installation order and Spare Drive number
(4/4)
DKU-14 DKU-15
Installation B4 Spare Installation B4 Spare
Order No. drive No. Order No. drive No.
081 11th Spare1 089 12th Spare1
082 11th Spare2 090 12th Spare2
083 11th Spare3 091 12th Spare3
084 11th Spare4 092 12th Spare4
085 11th Spare5 093 12th Spare5
086 11th Spare6 094 12th Spare6
087 11th Spare7 095 12th Spare7
088 11th Spare8 096 12th Spare8

INST03-11C-830
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-840

No. Model Number Model Name Data and Parity

1 DKC-F810I-1R6FM/3R2FM × 1 Flash Module Drive Spare Drive

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-01
016
012

015
011 DKU-03 DKU-05
032 048
014
028 044
010
031 047
013
027 043
009
030 046
DKU-00 026 042
008
029 045
004
025 041
007
DKU-02 DKU-04
003
024 040
006 020 036
002 023 039

005 019 035

001 022 038

018 034
DKC-0 *1: A data or
021 037
spare disk
017 033 is to be
installed.

Front View

Fig. 3.11.4.4-12 Spare Drive Expansion Sequence (1/2)

INST03-11C-840
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-850

RACK RACK RACK RACK RACK RACK

-12 -11 -10 -00 -01 -02

DKU-01
016
012

015
011 DKU-03 DKU-05
032 048
014
028 044
010
031 047
013
027 043
009
030 046
DKU-00 026 042
008
029 045
004
025 041
007
DKU-02 DKU-04
003
024 040
006 020 036
002 023 039

005 019 035

001 022 038

018 034
DKC-0 *1: A data or
021 037
spare disk
017 033 is to be
installed.

Front View

Fig. 3.11.4.4-12 Spare Drive Expansion Sequence (2/2)

INST03-11C-850
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-860

2. Checking the condition of the drive

a. Check the condition of the drive before installing it.

Drive (HDD/SSD)
Main Edge Connector

NOTICE: Check that the main edge connector of the drive

(HDD/SSD/FMD) has no deformation, damage or
sticking of dust before installing the drive.

Drive (FMD)

2-1 Installing the drives

NOTICE: When two or more drives are inserted at the same time, the already operating
drives might be blocked.
Insert the drives one by one at a second (*1) interval.
Don’t insert the drive that is not defined in the configuration.
*1: Interval of time necessary for stabilizing the voltage of the back board after
a drive insertion.

NOTICE: Be sure to wear your wrist strap and attach to ground prior to performing the
following work. This will ensure that the IC and LSI on the PCB are protected
from static electricity.

INST03-11C-860
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-870

In case of UBX

NOTICE: Since the Drive is a precision component, handle it very carefully not to apply a
vibration or shock to it.

a. Remove the dummy (drive) from the position installing the drive.
b. Open the handle fully and fit the drive in the guide rail and slide it in the direction shown by
the arrow not to give a shock.
NOTE: When handling the drive, hold the rail side because the shield spring is subject to
breakage.
c. Push the drive in until it reaches the position where a hook of the handle can be entered into
the square hole on a frame.
d. Pull the stopper lightly and close the handle, and then press the stopper to have the lock on.
If the handle is closed in the state where the hook of the handle cannot enter into the square
hole, the drive cannot be installed correctly because it runs into the frame of the drive
chassis.

Guide Rail

Dummy (Drive)

Square Hole Drive

Hook
Stopper
Drive Front View of Rail
UBX

Shield Spring
Handle

Fig. 3.11.4.4-13 Installation of Drives (In case of UBX)

INST03-11C-870
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-880

In case of SBX

NOTICE: Since the Drive is a precision component, handle it very carefully not to apply a
vibration or shock to it.

a. Remove the dummy (drive) from the position installing the drive.
b. Fit the drive in the guide rail and slide it in the direction shown by the arrow not to give a
shock.
c. Push the drive in until it reaches the position where a hook of the handle can be entered into
the square hole at the lower part of a frame on the front side of the drive box.
d. Raise the stopper, which has been tilted toward you, and then press the stopper to have the
lock on.
If the handle is raised in the state where the hook of the handle cannot enter into each hole,
the drive cannot be installed correctly because it runs into the frame of the drive chassis.

Dummy (Drive)

Front View of
SBX

Drive Drive

Handle
Guide Rail

Hook

Fig. 3.11.4.4-14 Installation of Drives (In case of SBX)

INST03-11C-880
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-890

In case of FBX

NOTICE: Be sure to detach the tape and remove the connector cover when installing the FMD.
Installing the FMD with the connector cover attached may cause equipment damage
or failure.
Connector Cover
Tape

Drive (FMD) Tape

INST03-11C-890
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-900

a. Remove the Dummy FMD from the installing position of a drive.

Release the hook while pressing the lock to the left to pull the Dummy FMD toward you.
b. Open the handle fully and fit the drive in the guide rail and slide it in the direction shown by
the arrow not to give a shock.
NOTE: When handling the drive, hold the rail side because the shield spring is subject to
breakage.
c. Push the drive in until it reaches the position where a hook of the handle can be entered into
the square hole on a frame.
d. Pull the stopper lightly and close the handle, and then press the stopper to have the lock on.
If the handle is closed in the state where the hook of the handle cannot enter into the square
hole, the drive cannot be installed correctly because it runs into the frame of the drive
chassis.

FBX

Dummy FMD

Lock

Hook

FBX

Guide Rail

Square Hole

Drive (FMD)

Hook

Rail Stopper
Shield Spring Handle

Fig. 3.11.4.4-15 Installation of Drive (In case of FBX)

INST03-11C-900
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-910

3.11.4.5 Installation Procedure of Device Interface Cable CC1 (DKC-F810I-CC1)

NOTE: Be sure to wear your wrist strap and attach to ground prior to performing the following
work. This will ensure that the IC and LSI on the PCB are protected from static electricity.

Installation Condition
DKC-F810I-CC1 is a cable option to connect between FBX and FBX in one rack.
Refer to below Table 3.11.4.5-1 for the condition of DKC-F810I-CC1 installation, and go to
the appropriate page.

Table 3.11.4.5-1 Work Procedure Table

No. Condition of Work Procedure Page
1 When Device Interface Cable CC1 (DKC-F810I-CC1) is INST03-11C-920
required to install.
2 When Device Interface Cable CC1 (DKC-F810I-CC1) is not INST03-11C-960
required to install.

Upper DKU
(FBX)

DKC-F810I-CC1
×2
Upper DKU
(FBX)

Lower DKU DKC-F810I-CC1

(FBX) ×2

DKC-x
Lower DKU
(FBX)

Rear View of RACK Rear View of RACK

Fig. 3.11.4.5-1 Mounting Position of Device Interface Cable

INST03-11C-910
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-920

1. Connection of cables
a. Remove the caps from the cables to be connected.
b. Connect the sixteen cables to the SSWs in the upper DKU after checking “3.1.6 Notes
when connecting the DEV interface cable” (INST03-01-180).

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.
Upper DKU
(FBX) CL1 6-0
(DKU-x(y+1))
SSWx(y+1)3-1
CL1 7-0 SSWx(y+1)3-2

CL2 6-0
CL1 4-0 CL2 7-0
SSWx(y+1)2-1
CL1 5-0 SSWx(y+1)2-2

CL2 4-0
Lower DKU
(FBX) CL1 2-0 CL2 5-0
Rear View (DKU-xy) SSWx(y+1)1-1
CL1 3-0 SSWx(y+1)1-2

SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 -0 -1 -2 -0 -1 -2
Front View of SSW CL2 2-0
CL1 0-0 CL2 3-0
Work before connecting SSWx(y+1)0-1
the cables CL1 1-0 SSWx(y+1)0-2

Cap

CL2 0-0
Cable
CL2 1-0
Fig. 3.11.4.5-2 Connection of Cables (CC1_DKU-x(y+1))

INST03-11C-920
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-930

c. Remove the caps from the cables to be connected.

d. Connect the sixteen cables to the SSWs in the lower DKU after checking “3.1.6 Notes
when connecting the DEV interface cable” (INST03-01-180).

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

Upper DKU
(FBX)
CL1 6-2
(DKU-x(y+1))
SSWxy3-1

CL1 7-2 SSWxy3-2

CL2 6-2
CL1 4-2 CL2 7-2
SSWxy2-1

CL1 5-2 SSWxy2-2

CL2 4-2
Lower DKU
(FBX) CL1 2-2 CL2 5-2
Rear View (DKU-xy) SSWxy1-1

CL1 3-2 SSWxy1-2

SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 -0 -1 -2 -0 -1 -2
Front View of SSW CL2 2-2
CL1 0-2 CL2 3-2
Work before connecting SSWxy0-1
the cables SSWxy0-2
CL1 1-2

Cap

Cable CL2 0-2

CL2 1-2
Fig. 3.11.4.5-3 Connection of Cables (CC1_DKU-xy)

INST03-11C-930
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-940

2. Attachment of cables
a. Route the eight cables in the cluster 1 and fix them with the loop cable ties.

Cable

Upper DKU (FBX)

Loop Cable Tie (DKU-x(y+1)

Lower DKU (FBX)

(DKU-xy)

Rear View of
RACK

Fig. 3.11.4.5-4 Fixation of Cables (DKU-xy (FBX) – DKU-x(y+1) (FBX))

INST03-11C-940
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-950

b. Route the eight cables in the cluster 2 and fix them with the loop cable ties.

Cable
Upper DKU (FBX)
(DKU-x(y+1))
Loop Cable Tie

Lower DKU (FBX)

(DKU-xy)

Rear View of
RACK

Fig. 3.11.4.5-5 Fixation of Cables (DKU-xy(FBX) – DKU-x(y+1) (FBX))

INST03-11C-950
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-960

3.11.4.6 Installation Procedure of Device Interface Cable CC2 (DKC-F810I-CC2)

NOTE: Be sure to wear your wrist strap and attach to ground prior to performing the following
work. This will ensure that the IC and LSI on the PCB are protected from static electricity.

Installation Condition
DKC-F810I-CC2 is a cable option to connect UBX/SBX and UBX/SBX/FBX in one rack. (See
Fig. 3.11.4.6-1 and Fig. 3.11.4.6-2.)
Refer to below Table 3.11.4.6-1 for the condition of DKC-F810I-CC2 installation, and go to
the appropriate page.

Table 3.11.4.6-1 Work Procedure Table

No. Condition of Work Procedure Page
1 When Device Interface Cable CC2 (DKC-F810I-CC2) is INST03-11C-980
required to install.
2 When Device Interface Cable CC2 (DKC-F810I-CC2) is not INST03-11C-1140
required to install.

Upper DKU
(UBX/SBX)

Upper DKU
(UBX/SBX)

DKC-F810I-CC2
×2

DKC-F810I-CC2
×2

Lower DKU
(UBX/SBX)

DKC-x
Lower DKU
(UBX/SBX)

Rear View of RACK Rear View of RACK

Fig. 3.11.4.6-1 Mounting Position of Device Interface Cable

INST03-11C-960
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-970

Upper DKU
(UBX/SBX)

Upper DKU
(UBX/SBX)

DKC-F810I-CC2
×2

Lower DKU DKC-F810I-CC2

(FBX) ×2

DKC-x
Lower DKU
(FBX)

Rear View of RACK Rear View of RACK

Upper DKU
(FBX)

DKC-F810I-CC2
×2
Upper DKU
(FBX)

DKC-F810I-CC2
×2

Lower DKU
(UBX/SBX)

DKC-x
Lower DKU
(FBX)

Rear View of RACK Rear View of RACK

Fig. 3.11.4.6-2 Mounting Position of Device Interface Cable

INST03-11C-970
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-980

1. Connection of cables
When connecting upper DKU (UBX/SBX) with lower DKU (UBX/SBX)
a. Remove the caps from the cables to be connected.
b. Connect the sixteen cables to the SSWs in the upper DKU after checking “3.1.6 Notes
when connecting the DEV interface cable” (INST03-01-180). (Refer to Fig. 3.11.4.6-3 and
Fig. 3.11.4.6-4.)

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.
Upper DKU
(UBX/SBX) SSWx(y+1)3-1
(DKU-x(y+1))

SSWx(y+1)3-2

CL1 3-0

CL2 3-0
SSWx(y+1)2-1

SSWx(y+1)2-2

CL1 2-0

CL2 2-0
SSWx(y+1)1-1

SSWx(y+1)1-2

CL1 1-0

CL2 1-0
SSWx(y+1)0-1

SSWx(y+1)0-2

CL1 0-0

CL2 0-0
Lower DKU
Work before connecting
(UBX/SBX)
the cables
Rear View (DKU-xy)

SSWxyz-1 SSWxyz-2
Cap
-0 -1 -2 -0 -1 -2
Front View of SSW Cable

Fig. 3.11.4.6-3 Connection of Cables (CC2_DKU-x(y+1)_L)

INST03-11C-980
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-990

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

Upper DKU
(UBX/SBX)
(DKU-x(y+1)) SSWx(y+1)7-1

SSWx(y+1)7-2

CL1 7-0

CL2 7-0
SSWx(y+1)6-1

SSWx(y+1)6-2

CL1 6-0

CL2 6-0
SSWx(y+1)5-1

SSWx(y+1)5-2

CL1 5-0

CL2 5-0
SSWx(y+1)4-1

SSWx(y+1)4-2

CL1 4-0

Lower DKU CL2 4-0

(UBX/SBX)
Rear View (DKU-xy) Work before connecting
the cables

SSWxyz-1 SSWxyz-2
Cap
-0 -1 -2 -0 -1 -2
Front View of SSW
Cable

Fig. 3.11.4.6-4 Connection of Cables (CC2_DKU-x(y+1)_U)

INST03-11C-990
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1000

c. Remove the caps from the cables to be connected.

d. Connect the sixteen cables to the SSWs in the lower DKU after checking “3.1.6 Notes
when connecting the DEV interface cable” (INST03-01-180). (Refer to Fig. 3.11.4.6-5 and
Fig. 3.11.4.6-6.)

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.
Upper DKU SSWxy3-1
(UBX/SBX)
(DKU-x(y+1))
SSWxy3-2

CL1 3-2

CL2 3-2
SSWxy2-1

SSWxy2-2

CL1 2-2

CL2 2-2
SSWxy1-1

SSWxy1-2

CL1 1-2

CL2 1-2
SSWxy0-1

SSWxy0-2

CL1 0-2
Lower DKU
(UBX/SBX) CL2 0-2
Rear View (DKU-xy) Work before connecting
the cables

SSWxyz-1 SSWxyz-2
Cap
-0 -1 -2 -0 -1 -2
Front View of SSW
Cable

Fig. 3.11.4.6-5 Connection of Cables (CC2_DKU-xy_L)

INST03-11C-1000
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1010

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

Upper DKU
(UBX/SBX)
(DKU-x(y+1)) SSWxy7-1

SSWxy7-2

CL1 7-2

CL2 7-2
SSWxy6-1

SSWxy6-2

CL1 6-2

CL2 6-2
SSWxy5-1

SSWxy5-2

CL1 5-2

CL2 5-2
SSWxy4-1

SSWxy4-2

CL1 4-2

Lower DKU
(UBX/SBX) CL2 4-2
Rear View (DKU-xy) Work before connecting
the cables

SSWxyz-1 SSWxyz-2
Cap
-0 -1 -2 -0 -1 -2
Front View of SSW
Cable

Fig. 3.11.4.6-6 Connection of Cables (CC2_DKU-xy_U)

INST03-11C-1010
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1020

When connecting upper DKU (UBX/SBX) with lower DKU (FBX)

a. Remove the caps from the cables to be connected.
b. Connect the sixteen cables to the SSWs in the upper DKU after checking “3.1.6 Notes
when connecting the DEV interface cable” (INST03-01-180). (Refer to Fig. 3.11.4.6-7 and
Fig. 3.11.4.6-8.)

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.
Upper DKU SSWx(y+1)3-1
(UBX/SBX)
(DKU-x(y+1))
SSWx(y+1)3-2

CL1 3-0

CL2 3-0
SSWx(y+1)2-1

SSWx(y+1)2-2

CL1 2-0

CL2 2-0
SSWx(y+1)1-1

SSWx(y+1)1-2

CL1 1-0

CL2 1-0
Lower DKU (FBX) SSWx(y+1)0-1
(DKU-xy)
Rear View SSWx(y+1)0-2
SSWxyz-1 SSWxyz-2
CL1 0-0
-0 -1 -2 -0 -1 -2
Front View of SSW
CL2 0-0
Work before connecting
the cables

Cap

Cable

Fig. 3.11.4.6-7 Connection of Cables (CC2_DKU-x(y+1)_L)

INST03-11C-1020
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1030

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

Upper DKU
(UBX/SBX) SSWx(y+1)7-1
(DKU-x(y+1))
SSWx(y+1)7-2

CL1 7-0

CL2 7-0
SSWx(y+1)6-1

SSWx(y+1)6-2

CL1 6-0

CL2 6-0
SSWx(y+1)5-1

SSWx(y+1)5-2

CL1 5-0

CL2 5-0
Lower DKU (FBX)
(DKU-xy) SSWx(y+1)4-1
Rear View
SSWx(y+1)4-2
SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 CL1 4-0
Front View of SSW
Work before connecting CL2 4-0
the cables

Cap

Cable

Fig. 3.11.4.6-8 Connection of Cables (CC2_DKU-x(y+1)_U)

INST03-11C-1030
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1040

c. Remove the caps from the cables to be connected.

d. Connect the sixteen cables to the SSWs in the lower DKU after checking “3.1.6 Notes
when connecting the DEV interface cable” (INST03-01-180).

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

Upper DKU
(UBX/SBX)
(DKU-x(y+1))
CL1 6-2
SSWxy3-1

CL1 7-2 SSWxy3-2

CL2 6-2
CL1 4-2 CL2 7-2
SSWxy2-1

CL1 5-2 SSWxy2-2

CL2 4-2
CL1 2-2 CL2 5-2
SSWxy1-1

CL1 3-2 SSWxy1-2

Lower DKU (FBX)

(DKU-xy)
Rear View
CL2 2-2
SSWxyz-1 SSWxyz-2 CL1 0-2 CL2 3-2
SSWxy0-1
-0 -1 -2 -0 -1 -2 -0 -1 -2 -0 -1 -2
Front View of SSW CL1 1-2 SSWxy0-2

Work before connecting

the cables

CL2 0-2
Cap CL2 1-2

Cable

Fig. 3.11.4.6-9 Connection of Cables (CC2_DKU-xy)

INST03-11C-1040
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1050

When connecting upper DKU (FBX) with lower DKU (UBX/SBX)

a. Remove the caps from the cables to be connected.
b. Connect the sixteen cables to the SSWs in the upper DKU after checking “3.1.6 Notes
when connecting the DEV interface cable” (INST03-01-180).

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

Upper DKU (FBX)

(DKU-x(y+1))
CL1 6-0
SSWx(y+1)3-1
CL1 7-0 SSWx(y+1)3-2

CL2 6-0
CL1 4-0 CL2 7-0
SSWx(y+1)2-1
CL1 5-0 SSWx(y+1)2-2

CL2 4-0
CL1 2-0 CL2 5-0
SSWx(y+1)1-1
CL1 3-0 SSWx(y+1)1-2

Lower DKU
(UBX/SBX) CL2 2-0
Rear View (DKU-xy) CL1 0-0 CL2 3-0
SSWxyz-1 SSWxyz-2 SSWx(y+1)0-1
CL1 1-0 SSWx(y+1)0-2
-0 -1 -2 -0 -1 -2 -0 -1 -2 -0 -1 -2
Front View of SSW
Work before connecting
the cables
CL2 0-0
CL2 1-0
Cap

Cable

Fig. 3.11.4.6-10 Connection of Cables (CC2_DKU-x(y+1))

INST03-11C-1050
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1060

c. Remove the caps from the cables to be connected.

d. Connect the sixteen cables to the SSWs in the lower DKU after checking “3.1.6 Notes
when connecting the DEV interface cable” (INST03-01-180). (Refer to Fig. 3.11.4.6-11
and Fig. 3.11.4.6-12.)

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

Upper DKU (FBX)

(DKU-x(y+1))
SSWxy3-1

SSWxy3-2

CL1 3-2

CL2 3-2
SSWxy2-1

SSWxy2-2

CL1 2-2

CL2 2-2
SSWxy1-1

SSWxy1-2

CL1 1-2

Lower DKU CL2 1-2

(UBX/SBX)
(DKU-xy) SSWxy0-1
Rear View
SSWxyz-1 SSWxyz-2 SSWxy0-2

-0 -1 -2 -0 -1 -2
Front View of SSW CL1 0-2

Work before connecting

CL2 0-2
the cables

Cap

Cable

Fig. 3.11.4.6-11 Connection of Cables (CC2_DKU-xy_L)

INST03-11C-1060
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1070

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

Upper DKU (FBX)

(DKU-x(y+1)) SSWxy7-1

SSWxy7-2

CL1 7-2

CL2 7-2
SSWxy6-1

SSWxy6-2

CL1 6-2

CL2 6-2
SSWxy5-1

SSWxy5-2

CL1 5-2

Lower DKU CL2 5-2

(UBX/SBX)
(DKU-xy) SSWxy4-1
Rear View
SSWxyz-1 SSWxyz-2 SSWxy4-2

-0 -1 -2 -0 -1 -2
CL1 4-2
Front View of SSW
Work before connecting CL2 4-2
the cables

Cap

Cable

Fig. 3.11.4.6-12 Connection of Cables (CC2_DKU-xy_U)

INST03-11C-1070
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1080

2. Attachment of cables
a. Route the eight cables in the cluster 1 and fix them with the loop cable ties. (Refer to Fig.
3.11.4.6-13, Fig. 3.11.4.6-14 or Fig. 3.11.4.6-15.)

Upper DKU
(UBX/SBX)
Loop Cable Tie
(DKU-x(y+1)

Cable

Lower DKU
(UBX/SBX)
Loop Cable Tie
(DKU-xy)

Rear View of
RACK

Fig. 3.11.4.6-13 Fixation of Cables (DKU-xy (UBX/SBX) – DKU-x(y+1) (UBX/SBX))

INST03-11C-1080
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1090

Upper DKU
(UBX/SBX)
(DKU-x(y+1)
Loop Cable Tie

Cable

Loop Cable Tie

Lower DKU
(FBX)
(DKU-xy)

Rear View of
RACK

Fig. 3.11.4.6-14 Fixation of Cables (DKU-xy(FBX) – DKU-x(y+1) (UBX/SBX))

INST03-11C-1090
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1100

Loop Cable Tie

Upper DKU
Cable (FBX)
(DKU-x(y+1)

Loop Cable Tie Lower DKU

(UBX/SBX)
(DKU-xy)

Rear View of
RACK

Fig. 3.11.4.6-15 Fixation of Cables (DKU-xy (UBX/SBX) – DKU-x(y+1) (FBX))

INST03-11C-1100
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1110

b. Route the eight cables in the cluster 2 and fix them with the loop cable ties. (Refer to Fig.
3.11.4.6-16, Fig. 3.11.4.6-17 or Fig. 3.11.4.6-18.)

Upper DKU
(UBX/SBX) Loop Cable Tie
(DKU-x(y+1)

Cable

Lower DKU
(UBX/SBX) Loop Cable Tie
(DKU-xy)

Rear View of
RACK

Fig. 3.11.4.6-16 Fixation of Cables (DKU-xy (UBX/SBX) – DKU-x(y+1) (UBX/SBX))

INST03-11C-1110
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1120

Upper DKU
(UBX/SBX)
(DKU-x(y+1)
Loop Cable Tie

Cable

Loop Cable Tie

Lower DKU
(FBX)
(DKU-xy)

Rear View of
RACK

Fig. 3.11.4.6-17 Fixation of Cables (DKU-xy (FBX) – DKU-x(y+1) (UBX/SBX))

INST03-11C-1120
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1130

Loop Cable Tie

Upper DKU
(FBX) Cable
(DKU-x(y+1)

Lower DKU Loop Cable Tie

(UBX/SBX)
(DKU-xy)

Rear View of
RACK

Fig. 3.11.4.6-18 Fixation of Cables (DKU-xy (UBX/SBX) – DKU-x(y+1) (UBX/SBX))

INST03-11C-1130
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1140

3.11.4.7 Installation Procedure of Device Interface Cable CC4 (DKC-F810I-CC4)

NOTE: Be sure to wear your wrist strap and attach to ground prior to performing the
following work. This will ensure that the IC and LSI on the PCB are protected from
static electricity.

Installation Condition
DKC-F810I-CC4 is a cable option to connect between DKU (UBX/SBX/FBX) and DKU
(UBX/SBX/FBX) in two racks. (See Fig. 3.11.4.7-1 through Fig. 3.11.4.7-4.)
Refer to below Table 3.11.4.7-1 for the condition of DKC-F810I-CC4 installation, and go to
the appropriate page.

Table 3.11.4.7-1 Work Procedure Table

No. Condition of Work Procedure Page
1 When Device Interface Cable CC4 (DKC-F810I-CC4) is INST03-11C-1190
required to install.
2 When Device Interface Cable CC4 (DKC-F810I-CC4) is not INST03-11C-1440
required to install.

INST03-11C-1140
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1150

UBX/SBX UBX/SBX

DKC-F810I- DKC-F810I-
CC4 × 2 CC4 × 2

UBX/SBX UBX/SBX

DKC-0 DKC-1

Rear View of RACK

UBX/SBX UBX/SBX

UBX/SBX UBX/SBX

DKC-F810I- DKC-F810I-
CC4 × 2 CC4 × 2
DKC-0 DKC-1

Rear View of RACK

Fig. 3.11.4.7-1 Mounting Position of Device Interface Cable (UBX/SBX – UBX/SBX)

INST03-11C-1150
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1160

FBX FBX

DKC-F810I- DKC-F810I-
CC4 × 2 CC4 × 2

FBX FBX

DKC-0 DKC-1

Rear View of RACK

FBX FBX

FBX FBX

DKC-F810I- DKC-F810I-
CC4 × 2 CC4 × 2
DKC-0 DKC-1

Rear View of RACK

Fig. 3.11.4.7-2 Mounting Position of Device Interface Cable (FBX – FBX)

INST03-11C-1160
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1170

UBX/SBX UBX/SBX

DKC-F810I- DKC-F810I-
CC4 × 2 CC4 × 2

FBX FBX

DKC-0 DKC-1

Rear View of RACK

UBX/SBX UBX/SBX

FBX FBX

DKC-F810I- DKC-F810I-
CC4 × 2 DKC-0 DKC-1 CC4 × 2

Rear View of RACK

Fig. 3.11.4.7-3 Mounting Position of Device Interface Cable (UBX/SBX – FBX)

INST03-11C-1170
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1180

FBX FBX

DKC-F810I- DKC-F810I-
CC4 × 2 CC4 × 2

UBX/SBX UBX/SBX

DKC-0 DKC-1

Rear View of RACK

FBX FBX

UBX/SBX UBX/SBX

DKC-F810I- DKC-F810I-
CC4 × 2 CC4 × 2
DKC-0 DKC-1

Rear View of RACK

Fig. 3.11.4.7-4 Mounting Position of Device Interface Cable (FBX – UBX/SBX)

INST03-11C-1180
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1190

1. Pattern of Cable Installation

Before starting the following procedure, remember the names and locations shown below.
In the following procedure, the rack from which the cable is connected is named as a
connection source rack, and the DKU from which the cable is connected is named as a
connection source DKU. The rack to which the cable is connected is named as a connection
destination rack, and the DKU to which the cable is connected is named as a connection
destination DKU.
There are a total of four patterns of cable installation between racks regardless of the type of
DKU.
If a DKC is installed in a connection source rack, the cables must be routed from the top of the
rack. If no DKC is installed in a connection source rack, the cables must be routed from the
bottom of the rack.
Pattern 1 Pattern 2

Connection Connection
Source Source
DKU DKU

Connection Connection
Destination Destination
DKU DKU
DKC DKC

Connection Connection Connection Connection

Destination RACK Source RACK Source RACK Destination RACK
Rear View Rear View

Pattern 3 Pattern 4

Connection Connection
Source Source
DKU DKU

Connection Connection
Destination Destination
DKU DKU
DKC DKC

Connection Connection RACK RACK Connection Connection

Destination RACK Source RACK Source RACK Destination RACK

Rear View Rear View NOTE: DKU: UBX/SBX ... 16U

FBX ... 8U

Fig. 3.11.4.7-5 Pattern of Cable Installation

INST03-11C-1190
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1200

2. Connection of cables
When connecting Connection Destination DKU (UBX/SBX) with Connection Source DKU
(UBX/SBX)
a. Remove the caps from the cables to be connected.
b. Connect the sixteen cables to the SSWs in the connection destination DKU after checking
“3.1.6 Notes when connecting the DEV interface cable” (INST03-01-180). (Refer to Fig.
3.11.4.7-6 and Fig. 3.11.4.7-7.)

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

SSWx(y+1)3-1

SSWx(y+1)3-2

CL1 3-0

CL2 3-0
SSWx(y+1)2-1

SSWx(y+1)2-2

CL1 2-0
Connection Source DKU
(UBX/SBX) (DKU-xy)
CL2 2-0
SSWx(y+1)1-1

SSWx(y+1)1-2
Connection Destination DKU
(UBX/SBX) (DKU-x(y+1))
Rear View CL1 1-0

CL2 1-0
SSWx(y+1)0-1
Work before connecting
the cables
SSWx(y+1)0-2

Cap CL1 0-0

CL2 0-0
Cable
SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2
Front View of SSW
Fig. 3.11.4.7-6 Connection of Cables (CC4_DKU-x(y+1)_L)
INST03-11C-1200
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1210

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

SSWx(y+1)7-1

SSWx(y+1)7-2

CL1 7-0

CL2 7-0
SSWx(y+1)6-1

SSWx(y+1)6-2

CL1 6-0
Connection Source DKU
(UBX/SBX) (DKU-xy)
CL2 6-0
SSWx(y+1)5-1

SSWx(y+1)5-2
Connection Destination DKU
(UBX/SBX) (DKU-x(y+1))
Rear View CL1 5-0

CL2 5-0
SSWx(y+1)4-1
Work before connecting
the cables
SSWx(y+1)4-2

Cap CL1 4-0

CL2 4-0
Cable
SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2
Front View of SSW
Fig. 3.11.4.7-7 Connection of Cables (CC4_DKU-x(y+1)_U)

INST03-11C-1210
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1220

c. Remove the caps from the cables to be connected.

d. Connect the sixteen cables to the SSWs in the connection source DKU after checking
“3.1.6 Notes when connecting the DEV interface cable” (INST03-01-180). (Refer to Fig.
3.11.4.7-8 and Fig. 3.11.4.7-9.)

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

SSWxy3-1

SSWxy3-2

CL1 3-2

CL2 3-2
SSWxy2-1

SSWxy2-2

CL1 2-2
Connection Source DKU
(UBX/SBX) (DKU-xy)
CL2 2-2
SSWxy1-1

Connection Destination DKU SSWxy1-2

(UBX/SBX) (DKU-x(y+1))
Rear View CL1 1-2

CL2 1-2
Work before connecting
SSWxy0-1
the cables
SSWxy0-2

Cap CL1 0-2

Cable CL2 0-2

SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2
Front View of SSW

Fig. 3.11.4.7-8 Connection of Cables (CC4_DKU-xy_L)

INST03-11C-1220
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1230

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

SSWxy7-1

SSWxy7-2

CL1 7-2

CL2 7-2
SSWxy6-1

SSWxy6-2

CL1 6-2
Connection Source DKU
(UBX/SBX) (DKU-xy)
CL2 6-2
SSWxy5-1

SSWxy5-2
Connection Destination DKU
(UBX/SBX) (DKU-x(y+1))
Rear View CL1 5-2

CL2 5-2
Work before connecting SSWxy4-1
the cables
SSWxy4-2

Cap CL1 4-2

Cable CL2 4-2

SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2
Front View of SSW

Fig. 3.11.4.7-9 Connection of Cables (CC4_DKU-xy_U)

INST03-11C-1230
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1240

When connecting Connection Destination DKU (FBX) with Connection Source DKU (FBX)
a. Remove the caps from the cables to be connected.
b. Connect the sixteen cables to the SSWs in the connection destination DKU after checking
“3.1.6 Notes when connecting the DEV interface cable” (INST03-01-180).

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

CL1 6-0
SSWx(y+1)3-1
CL1 7-0 SSWx(y+1)3-2

CL2 6-0
CL1 4-0 CL2 7-0
SSWx(y+1)2-1
CL1 5-0 SSWx(y+1)2-2
Connection Source DKU
(FBX) (DKU-xy)

CL2 4-0
CL1 2-0 CL2 5-0
Connection Destination DKU SSWx(y+1)1-1
(FBX) (DKU-x(y+1))
CL1 3-0 SSWx(y+1)1-2
Rear View

SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 -0 -1 -2 -0 -1 -2 CL2 2-0
Front View of SSW CL1 0-0 CL2 3-0

Work before connecting SSWx(y+1)0-1

the cables CL1 1-0 SSWx(y+1)0-2

Cap
CL2 0-0
Cable CL2 1-0

Fig. 3.11.4.7-10 Connection of Cables (CC4_DKU-x(y+1))

INST03-11C-1240
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1250

c. Remove the caps from the cables to be connected.

d. Connect the sixteen cables to the SSWs in the connection source DKU after checking
“3.1.6 Notes when connecting the DEV interface cable” (INST03-01-180).

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

CL1 6-2
SSWxy3-1

CL1 7-2 SSWxy3-2

CL2 6-2
CL1 4-2 CL2 7-2
SSWxy2-1

CL1 5-2 SSWxy2-2

Connection Source DKU

(FBX) (DKU-xy)
CL2 4-2
CL1 2-2 CL2 5-2
SSWxy1-1
Connection Destination DKU SSWxy1-2
CL1 3-2
(FBX) (DKU-x(y+1))
Rear View

SSWxyz-1 SSWxyz-2
CL2 2-2
-0 -1 -2 -0 -1 -2 -0 -1 -2 -0 -1 -2
CL1 0-2 CL2 3-2
Front View of SSW SSWxy0-1

Work before connecting CL1 1-2 SSWxy0-2

the cables

Cap
CL2 0-2
CL2 1-2
Cable

Fig. 3.11.4.7-11 Connection of Cables (CC4_DKU-xy)

INST03-11C-1250
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1260

When connecting Connection Destination DKU (UBX/SBX) with Connection Source DKU (FBX)
a. Remove the caps from the cables to be connected.
b. Connect the sixteen cables to the SSWs in the connection destination DKU after checking
“3.1.6 Notes when connecting the DEV interface cable” (INST03-01-180). (Refer to Fig.
3.11.4.7-12 and Fig. 3.11.4.7-13.)

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

SSWx(y+1)3-1

SSWx(y+1)3-2

CL1 3-0

CL2 3-0
SSWx(y+1)2-1

SSWx(y+1)2-2

CL1 2-0
Connection Source DKU
(FBX) (DKU-xy)
CL2 2-0
SSWx(y+1)1-1

SSWx(y+1)1-2
Connection Destination DKU
(UBX/SBX) (DKU-x(y+1))
CL1 1-0
Rear View
CL2 1-0
SSWx(y+1)0-1
Work before connecting
the cables SSWx(y+1)0-2

CL1 0-0
Cap
CL2 0-0
Cable
SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2
Front View of SSW
Fig. 3.11.4.7-12 Connection of Cables (CC4_DKU-x(y+1)_L)

INST03-11C-1260
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1270

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

SSWx(y+1)7-1

SSWx(y+1)7-2

CL1 7-0

CL2 7-0
SSWx(y+1)6-1

SSWx(y+1)6-2

CL1 6-0

Connection Source DKU

(FBX) (DKU-xy) CL2 6-0
SSWx(y+1)5-1

SSWx(y+1)5-2
Connection Destination DKU
(UBX/SBX) (DKU-x(y+1)) CL1 5-0
Rear View
CL2 5-0
SSWx(y+1)4-1

Work before connecting SSWx(y+1)4-2

the cables
CL1 4-0
Cap
CL2 4-0

Cable
SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2
Front View of SSW
Fig. 3.11.4.7-13 Connection of Cables (CC4_DKU-x(y+1)_U)

INST03-11C-1270
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1280

c. Remove the caps from the cables to be connected.

d. Connect the sixteen cables to the SSWs in the connection source DKU after checking
“3.1.6 Notes when connecting the DEV interface cable” (INST03-01-180).

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

CL1 6-2 SSWxy3-1

CL1 7-2 SSWxy3-2

CL2 6-2
CL1 4-2 CL2 7-2
SSWxy2-1

CL1 5-2 SSWxy2-2

Connection Source DKU

(FBX) (DKU-xy)
CL2 4-2
CL1 2-2 CL2 5-2
SSWxy1-1
Connection Destination DKU
CL1 3-2 SSWxy1-2
(UBX/SBX) (DKU-x(y+1))
Rear View

SSWxyz-1 SSWxyz-2
CL2 2-2
-0 -1 -2 -0 -1 -2 -0 -1 -2 -0 -1 -2
CL1 0-2 CL2 3-2
Front View of SSW
SSWxy0-1

Work before connecting CL1 1-2 SSWxy0-2

the cables

Cap
CL2 0-2
CL2 1-2
Cable

Fig. 3.11.4.7-14 Connection of Cables (CC4_DKU-xy)

INST03-11C-1280
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1290

When connecting Connection Destination DKU (FBX) with Connection Source DKU (UBX/SBX)
a. Remove the caps from the cables to be connected.
b. Connect the sixteen cables to the SSWs in the connection destination DKU after checking
“3.1.6 Notes when connecting the DEV interface cable” (INST03-01-180).

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

CL1 6-0 SSWx(y+1)3-1

CL1 7-0 SSWx(y+1)3-2

CL2 6-0
CL1 4-0 CL2 7-0
SSWx(y+1)2-1
CL1 5-0 SSWx(y+1)2-2
Connection Source DKU
(UBX/SBX) (DKU-xy)

CL2 4-0
Connection Destination DKU CL1 2-0 CL2 5-0
(FBX) (DKU-x(y+1)) SSWx(y+1)1-1
Rear View CL1 3-0 SSWx(y+1)1-2

SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 -0 -1 -2 -0 -1 -2
CL2 2-0
Front View of SSW
CL1 0-0 CL2 3-0

Work before connecting SSWx(y+1)0-1

the cables CL1 1-0 SSWx(y+1)0-2

Cap
CL2 0-0
Cable CL2 1-0

Fig. 3.11.4.7-15 Connection of Cables (CC4_DKU-x(y+1))

INST03-11C-1290
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1300

c. Remove the caps from the cables to be connected.

d. Connect the sixteen cables to the SSWs in the connection source DKU after checking
“3.1.6 Notes when connecting the DEV interface cable” (INST03-01-180). (Refer to Fig.
3.11.4.7-16 and Fig. 3.11.4.7-17.)

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

SSWxy3-1

SSWxy3-2

CL1 3-2

CL2 3-2
SSWxy2-1

SSWxy2-2

Connection Source DKU CL1 2-2

(UBX/SBX) (DKU-xy)
CL2 2-2
SSWxy1-1

SSWxy1-2
Connection Destination DKU
(FBX) (DKU-x(y+1))
Rear View CL1 1-2

CL2 1-2
SSWxy0-1

SSWxy0-2
Work before connecting
the cables
CL1 0-2

Cap CL2 0-2

SSWxyz-1 SSWxyz-2
Cable
-0 -1 -2 -0 -1 -2
Front View of SSW
Fig. 3.11.4.7-16 Connection of Cables (CC4_DKU-xy_L)

INST03-11C-1300
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1310

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

SSWxy7-1

SSWxy7-2

CL1 7-2

CL2 7-2
SSWxy6-1

SSWxy6-2

CL1 6-2
Connection Source DKU
(UBX/SBX) (DKU-xy)
CL2 6-2
SSWxy5-1

SSWxy5-2
Connection Destination DKU
(FBX) (DKU-x(y+1))
Rear View CL1 5-2

CL2 5-2
SSWxy4-1

SSWxy4-2
Work before connecting
the cables CL1 4-2

CL2 4-2
Cap

SSWxyz-1 SSWxyz-2
Cable
-0 -1 -2 -0 -1 -2
Front View of SSW
Fig. 3.11.4.7-17 Connection of Cables (CC4_DKU-xy_U)

INST03-11C-1310
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1320

3. Attachment of Cables
In the case of cable installation between DKU in RACK-00 and DKU in RACK-01
a. Install the two rack nuts to the rear side of the RACK-01.

Lower Hole 42U Lower Hole

41U
of 41st Unit 40U
of 41st Unit
39U
38U
37U
36U
35U
34U
33U

Rear View of RACK-01

Rack Frame
(Rear Side)

Rack Nut

Fig. 3.11.4.7-18 Installation of Rack Nuts

b. Attach the two loop cable ties to the rear side of the RACK-01and secure them with the
two screws.
Frame
Loop Cable Tie

Screw

Loop Cable Tie

41U

Rear View of
RACK-01

Screw

Fig. 3.11.4.7-19 Attachment of Loop Cable Ties

INST03-11C-1320
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1330

c. Route the eight cables in the cluster 1 and fix them with the loop cable ties.
In the case of FBX, the cable routing is the same. Remove the cables seeing the figure
below.

Cable
Connection Source
DKU (DKU-0y)

Loop Cable Tie

Connection
Destination DKU
(DKU-0(y+1))

Loop Cable Tie

RACK-01

RACK-00
Rear View

Fig. 3.11.4.7-20 Fixation of Cables (RACK-00 – RACK-01)

INST03-11C-1330
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1340

d. Route the eight cables in the cluster 2 and fix them with the loop cable ties.
In the case of FBX, the cable routing is the same. Remove the cables seeing the figure
below.

Connection Source
DKU (DKU-0y)

Loop Cable Tie

Loop Cable Tie

Cable

Connection
Destination DKU
(DKU-0(y+1))

Loop Cable Tie

RACK-00

RACK-01
Rear View

Fig. 3.11.4.7-21 Fixation of Cables (RACK-00 – RACK-01)

INST03-11C-1340
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1350

In the case of cable installation between DKU in RACK-10 and DKU in RACK-11
a. Install the two rack nuts to the rear side of the RACK-11.

Lower Hole 42U Lower Hole

41U
of 41st Unit 40U
of 41st Unit
39U
38U
37U
36U
35U
34U
33U

Rear View of RACK-11

Rack Frame
(Rear Side)

Rack Nut

Fig. 3.11.4.7-22 Installation of Rack Nuts

b. Attach the two loop cable ties to the rear side of the RACK-11 and secure them with the
two screws.
Frame
Loop Cable Tie

Screw

Loop Cable Tie

41U

Rear View of
RACK-11

Screw

Fig. 3.11.4.7-23 Attachment of Loop Cable Ties

INST03-11C-1350
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1360

c. Route the eight cables in the cluster 1 and fix them with the loop cable ties.
In the case of FBX, the cable routing is the same. Remove the cables seeing the figure
below.

Connection Source
DKU (DKU-1y)

Loop Cable Tie

Cable
Loop Cable Tie

Connection
Destination DKU
(DKU-1(y+1))

Loop Cable Tie

RACK-10

RACK-11
Rear View

Fig. 3.11.4.7-24 Fixation of Cables (RACK-10 – RACK-11)

INST03-11C-1360
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1370

d. Route the eight cables in the cluster 2 and fix them with the loop cable ties.
In the case of FBX, the cable routing is the same. Remove the cables seeing the figure
below.

Cable

Connection Source
DKU (DKU-1y)

Loop Cable Tie

Connection
Destination DKU
(DKU-1(y+1))

Loop Cable Tie

RACK-11

RACK-10
Rear View

Fig. 3.11.4.7-25 Fixation of Cables (RACK-10 – RACK-11)

INST03-11C-1370
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1380

In the case of cable installation between DKU in RACK-01 and DKU in RACK-02
a. Install the two rack nuts to the rear side of the RACK-02.

10U
9U
8U
7U
6U
5U
4U
Upper Hole 3U Upper Hole
of 2nd Unit 2U of 2nd Unit
1U

Rear View of RACK-02

Rack Frame
(Rear Side)

Rack Nut

Fig. 3.11.4.7-26 Installation of Rack Nuts

b. Attach the two loop cable ties to the rear side of the RACK-02 and secure them with the
two screws.
Frame
Loop Cable Tie

Screw

Loop Cable Tie

Rear View of
RACK-02

Screw

Fig. 3.11.4.7-27 Attachment of Loop Cable Ties

INST03-11C-1380
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1390

c. Route the eight cables in the cluster 1 and fix them with the loop cable ties.
In the case of FBX, the cable routing is the same. Remove the cables seeing the figure
below.

Connection Source
DKU (DKU-0y)

Connection Destination
DKU (DKU-0(y+1))

Loop Cable Tie

Loop Cable Tie

Extra Length
Adjustment
RACK-02

Cable

Rear View RACK-01

Fig. 3.11.4.7-28 Fixation of Cables (RACK-01 – RACK-02)

INST03-11C-1390
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1400

d. Route the eight cables in the cluster 2 and fix them with the loop cable ties.
In the case of FBX, the cable routing is the same. Remove the cables seeing the figure
below.

Connection Source
DKU (DKU-0y)

Loop Cable Tie

Connection Destination
DKU (DKU-0(y+1))

Cable
Loop Cable Tie

RACK-01

RACK-02

Extra Length Rear View

Adjustment

Fig. 3.11.4.7-29 Fixation of Cables (RACK-01 – RACK-02)

INST03-11C-1400
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1410

In the case of cable installation between DKU in RACK-11 and DKU in RACK-12
a. Install the two rack nuts to the rear side of the RACK-12.

10U
9U
8U
7U
6U
5U
4U
Upper Hole 3U Upper Hole
of 2nd Unit 2U of 2nd Unit
1U

Rear View of RACK-12

Rack Frame
(Rear Side)

Rack Nut

Fig. 3.11.4.7-30 Installation of Rack Nuts

b. Attach the two loop cable ties to the rear side of the RACK-12 and secure them with the
two screws.
Frame
Loop Cable Tie

Screw

Loop Cable Tie

Rear View of
RACK-12

Screw

Fig. 3.11.4.7-31 Attachment of Loop Cable Ties

INST03-11C-1410
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1420

c. Route the eight cables in the cluster 1 and fix them with the loop cable ties.
In the case of FBX, the cable routing is the same. Remove the cables seeing the figure
below.

Connection Source
DKU (DKU-1y)

Loop Cable Tie

Connection Destination
DKU (DKU-1(y+1))

Loop Cable Tie

Cable

RACK-11

RACK-12 Extra Length

Rear View Adjustment

Fig. 3.11.4.7-32 Fixation of Cables (RACK-11 – RACK-12)

INST03-11C-1420
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1430

d. Route the eight cables in the cluster 2 and fix them with the loop cable ties.
In the case of FBX, the cable routing is the same. Remove the cables seeing the figure
below.

Connection Source
DKU (DKU-1y)

Connection Destination
DKU (DKU-1(y+1))

Loop Cable Tie

Loop Cable Tie

Extra Length
Adjustment
RACK-12

Cable

RACK-11 Rear View

Fig. 3.11.4.7-33 Fixation of Cables (RACK-11 – RACK-12)

INST03-11C-1430
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1440

3.11.4.8 SVP post procedure

(1) <Check that hardware components are installed>
Select (CL) [OK] after making sure that all
hardware components are installed correctly
in response to “Insert the PDEV/DKU on the
storage system. Turn on the circuit breakers
on the DKUPS and PDU. After the operations
are completed, select [OK] button.”.

NOTE: Confirm that all the Device Interface

Cables to install are connected to the SSW PCBs. If the Device Interface Cables are
not connected, connect the Cables referring to
“3.11.4.6 Installation Procedure of Device Interface Cable CC2 (DKC-F810I-CC2)”
(INST03-11C-960),
“3.11.4.7 Installation Procedure of Device Interface Cable CC4 (DKC-F810I-CC4)”
(INST03-11C-1140).
When the breaker of PDU is OFF, please turn it on.

(2) <DKU PATH INLINE>

When DKA is installed, “DKU PATH INLINE is now running...” is displayed.

(3) <LDEV FORMAT>

“Formatting logical devices...” is displayed when Parity Group is defined.

(4) <End of system update processing>

“Renewal process has completed. Please
check storage system status.” is displayed
when recovery processing on all installed
components is completed. Select (CL) [OK]
in response to this message.

(4)-1 <QUICK FORMAT>

Refer to the logical device window in the “Maintenance” window to check that the Quick
Format is in progress. (SVP03-06-10 through 100)

INST03-11C-1440
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11C-1450

(5)
Execute an operation for backing up the
configuration information.
Prepare the removable media for backup and
insert the media.
Please select (CL) the [Refresh] button, and
update drive information.
Select (CL) the drive and the PC in which the
media was inserted. Select (CL) the [OK]
button.
NOTE: For the procedure of backing up the
configuration information to a CD-R,
see page MICRO07-190.

(6)
When this procedure is completed, the message “Please
remove the Config media.” is displayed.
Remove the configuration information media,
select (CL) [OK].

(7)
After the procedure is completed, return to ‘Install’.
Select (CL) [File]-[Exit].

(8) <Mode Change>

Change the mode to View Mode.

(9) Return to the work table and perform rest of the works.
New Installation: INST02-20
Non-Disruptive Installation: INST02-50

INST03-11C-1450
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-10

3.11.5 When performing addition of the DKA and DEV interface cable that accompanies the
addition of the DKU-00/10 (only hardware procedure) (DKC-F810I-SCA/CC1/CC2)
3.11.5.1 In the case of Standard Model
To connect the DKA and DKU-00/10 in the standard model, the cable options shown in the table
below are required.
For the high-performance model, go to “3.11.5.2 In the case of High-performance Model”
(INST03-11D-220).

Table 3.11.5.1-1 Required Cable Options

No. Model Number Quantity Description
1 DKC-F810I-CC1 1 1m cable × 8
2 DKC-F810I-CC2 1 2m cable × 8

Standard Model

DKC-F810I-CC1
DKU-00/10
(UBX/SBX)

DKC-F810I-CC1

DKU-00/10
(FBX)

DKC-F810I-CC2 DKC-F810I-CC2

DKA DKA DKA DKA

DKC-0/1 DKC-0/1
Rear View of Rear View of
Rack Rack

Fig. 3.11.5.1-1 Cable Routing

INST03-11D-10
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-20

1. Installation Procedure of Disk Adapter

NOTICE: Be sure to wear your wrist strap and attach to ground prior to performing the
following work. This will ensure that the IC and LSI on the PCB are protected
from static electricity.

1-1 Insertion of PCBs

a. Loosen the screws and remove the dummy plates. Refer to the Table 3.11.5.1-2 and Fig.
3.11.5.1-2.
NOTE: Store the removed dummy plates as they are required when the DKAs are removed.
b. Insert the PCBs to the correct locations in the DKC and tighten the screw.

Main Edge Connector

PCB NOTICE: • Check that the main edge connector of the PCB has
no deformation, damage or sticking of dust before
installing the PCB. (See INST03-01-80)
• When installing the PCB, hold the right and left of the
PCB with both hands, and insert it straight not to
contact the neighboring PCB.

Table 3.11.5.1-2 Inserting Location

DKC Addition No. Location No. Remarks
Cluster 1 Cluster 2
DKC-0 Basic DKA-1PA DKA-2PA
DKC-1 Option 2 DKA-1PG DKA-2PG

INST03-11D-20
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-30

1 1 2 2 1 1 2 2
P P P P P P P P
A B B A G H HG

Rear View of DKC-0 Rear View of DKC-1

DKC

DKA PCB

Lever Screw

Screw

Dummy Plate

Lever Screw
Screw
Fig. 3.11.5.1-2 Insertion of PCB

INST03-11D-30
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-40

2. Attachment of Device Interface Cable (CC2)

2-1 Attach the location labels to the cables.
a. Attach 16 location labels to 8 cables. Choose location labels from Labels (Address) and
Labels (Address) 2. See Fig. 3.11.5.1-3, Table 3.11.5.1-3, and Table 3.11.5.1-4.
b. Stick the Label (Protect) around the attached location labels.

Location Label  Location Label 

80mm 80mm

[Label Attachment Example] Cable

Cable

Location Label

Edge

Label (Protect)

 Attach the location label to the MFC cable.

 Attach the Label (Protect) to the location label with its edge aligned with the location label.
 Stick the Label (Protect) around the location label so that the location label is not torn off.

Fig. 3.11.5.1-3 Attachment of Location Labels

Table 3.11.5.1-3 Location Label List (DKC-0 (DKA-1PA/2PA) – DKU-00)

No. Connection Source (DKC-0) Connection Destination (DKU-00)
Part Name Location Label Color Part Name Location Label Color
Label  UBX/SBX FBX Label
1 DKA-1PA CL1 1PA-0 White/Black SSW000-1 SSW000-1 CL1 0-0 White/Black
2 DKA-1PA CL1 1PA-1 White/Brown SSW002-1 SSW001-1 CL1 2-0 White/Red
3 DKA-1PA CL1 1PA-2 White/Red SSW004-1 SSW002-1 CL1 4-0 White/Yellow
4 DKA-1PA CL1 1PA-3 White/Orange SSW006-1 SSW003-1 CL1 6-0 White/Blue
5 DKA-2PA CL2 2PA-0 Yellow/Black SSW001-2 SSW000-2 CL2 1-0 Yellow/Brown
6 DKA-2PA CL2 2PA-1 Yellow/Brown SSW003-2 SSW001-2 CL2 3-0 Yellow/Orange
7 DKA-2PA CL2 2PA-2 Yellow/Red SSW005-2 SSW002-2 CL2 5-0 Yellow/Green
8 DKA-2PA CL2 2PA-3 Yellow/Orange SSW007-2 SSW003-2 CL2 7-0 Yellow/Purple

INST03-11D-40
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-50

Table 3.11.5.1-4 Location Label List (DKC-1 (DKA-1PG/2PG) – DKU-10)

No. Connection Source (DKC-1) Connection Destination (DKU-10)
Part Name Location Label Color Part Name Location Label Color
Label  UBX/SBX FBX Label
1 DKA-1PG CL1 1PG-0 White/Black SSW100-1 SSW100-1 CL1 0-0 White/Black
2 DKA-1PG CL1 1PG-1 White/Brown SSW102-1 SSW101-1 CL1 2-0 White/Red
3 DKA-1PG CL1 1PG-2 White/Red SSW104-1 SSW102-1 CL1 4-0 White/Yellow
4 DKA-1PG CL1 1PG-3 White/Orange SSW106-1 SSW103-1 CL1 6-0 White/Blue
5 DKA-2PG CL2 2PG-0 Yellow/Black SSW101-2 SSW100-2 CL2 1-0 Yellow/Brown
6 DKA-2PG CL2 2PG-1 Yellow/Brown SSW103-2 SSW101-2 CL2 3-0 Yellow/Orange
7 DKA-2PG CL2 2PG-2 Yellow/Red SSW105-2 SSW102-2 CL2 5-0 Yellow/Green
8 DKA-2PG CL2 2PG-3 Yellow/Orange SSW107-2 SSW103-2 CL2 7-0 Yellow/Purple

INST03-11D-50
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-60

2-2 Connection of Cables

In the case of cable installation between DKA-1PA/2PA and DKU-00

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.
a. Remove the caps from the cables to be connected.
b. Connect the cables to the DKA PCBs in the DKC-0 after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180).

DKAPCB DKA PCB

(DKA-1PA) (DKA-2PA)

CL1 1PA-0 CL2 2PA-0

CL1 1PA-1 CL2 2PA-1

CL1 1PA-2 CL2 2PA-2

CL1 1PA-3 CL2 2PA-3

Work before connecting

the cables.

Cap

Cable

Fig. 3.11.5.1-4 Connection of Cables

INST03-11D-60
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-70

When the DKU-00 is the UBX/SBX

c. Remove the caps from the cables to be connected.
d. Connect the eight cables to the SSWs in the DKU after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180). (Refer to Fig. 3.11.5.1-5 and Fig.
3.11.5.1-6.)

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-00 is the UBX/SBX.

SSW006-1

CL1 6-0

SSW004-1

CL1 4-0

Rear View of SSW002-1

DKU-00 (UBX/SBX)

SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 CL1 2-0
Front View of SSW

Work before connecting SSW000-1

the cables.

Cap CL1 0-0

Cable

Fig. 3.11.5.1-5 Connection of Cables (CC2_DKU-00 (UBX/SBX)_CL1)

INST03-11D-70
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-80

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-00 is the UBX/SBX.

SSW007-2

CL2 7-0

SSW005-2

Rear View of CL2 5-0

DKU-00(UBX/SBX)

SSWxyz-1 SSWxyz-2 SSW003-2

-0 -1 -2 -0 -1 -2
Front View of SSW

Work before connecting CL2 3-0

the cables.

SSW001-2

Cap

Cable
CL2 1-0

Fig. 3.11.5.1-6 Connection of Cables (CC2_DKU-00 (UBX/SBX)_CL2)

INST03-11D-80
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-90

When the DKU-00 is the FBX

c. Remove the caps from the cables to be connected.
d. Connect the eight cables to the SSWs in the DKU after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180).

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-00 is the FBX.

CL1 6-0
SSW003-1

SSW003-2
CL2 7-0

CL1 4-0
Rear View of DKU-00 (FBX) SSW002-1

SSW002-2
CL2 5-0
SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 -0 -1 -2 -0 -1 -2
CL1 2-0
Front View of SSW SSW001-1

Work before connecting

SSW001-2
the cables.
CL2 3-0

Cap CL1 0-0

SSW000-1
Cable
SSW000-2

CL2 1-0

Fig. 3.11.5.1-7 Connection of Cables (CC2_DKU-00 (FBX)_CL1/CL2)

INST03-11D-90
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-100

In the case of cable installation between DKA-1PG/2PG and DKU-10

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.
a. Remove the caps from the cables to be connected.
b. Connect the cables to the DKA PCBs in the DKC-1 after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180).

DKAPCB DKA PCB

(DKA-1PG) (DKA-2PG)

CL1 1PG-0 CL2 2PG-0

CL1 1PG-1 CL2 2PG-1

CL1 1PG-2 CL2 2PG-2

CL1 1PG-3 CL2 2PG-3

Work before connecting
the cables.

Cap

Cable

Fig. 3.11.5.1-8 Connection of Cables

INST03-11D-100
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-110

When the DKU-10 is the UBX/SBX

c. Remove the caps from the cables to be connected.
d. Connect the eight cables to the SSWs in the DKU after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180). (Refer to Fig. 3.11.5.1-9 and Fig.
3.11.5.1-10.)

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-10 is the UBX/SBX.

SSW106-1

CL1 6-0

SSW104-1

CL1 4-0

Rear View of SSW102-1

DKU-10 (UBX/SBX)

SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 CL1 2-0
Front View of SSW

Work before connecting SSW100-1

the cables.

Cap CL1 0-0

Cable

Fig. 3.11.5.1-9 Connection of Cables (CC2_DKU-10 (UBX/SBX)_CL1)

INST03-11D-110
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-120

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-10 is the UBX/SBX.

SSW107-2

CL2 7-0

SSW105-2

Rear View of CL2 5-0

DKU-10 (UBX/SBX)

SSWxyz-1 SSWxyz-2 SSW103-2

-0 -1 -2 -0 -1 -2
Front View of SSW

Work before connecting CL2 3-0

the cables.

SSW101-2

Cap

Cable
CL2 1-0

Fig. 3.11.5.1-10 Connection of Cables (CC2_DKU-10 (UBX/SBX)_CL2)

INST03-11D-120
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-130

When the DKU-10 is the FBX

c. Remove the caps from the cables to be connected.
d. Connect the eight cables to the SSWs in the DKU after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180).

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-10 is the FBX.

CL1 6-0
SSW103-1

SSW103-2
CL2 7-0

Rear View of DKU-10 (FBX) CL1 4-0

SSW102-1

SSW102-2
SSWxyz-1 SSWxyz-2 CL2 5-0

-0 -1 -2 -0 -1 -2 -0 -1 -2 -0 -1 -2
Front View of SSW CL1 2-0
SSW101-1
Work before connecting
the cables.
SSW101-2
CL2 3-0

Cap
CL1 0-0
SSW100-1
Cable

SSW100-2

CL2 1-0

Fig. 3.11.5.1-11 Connection of Cables (CC2_DKU-10 (FBX)_CL1/CL2)

INST03-11D-130
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-140

3. Attachment of Device Interface Cable (CC1)

3-1 Attach the location labels to the cables.
a. Attach 16 location labels to 8 cables. Choose location labels from Labels (Address) and
Labels (Address) 2.
b. Stick the Label (Protect) around the attached location labels.

Location Label  Location Label 

80mm 80mm

Cable

[Label Attachment Example]

Cable

Location Label

Edge

Label (Protect)

 Attach the location label to the MFC cable.

 Attach the Label (Protect) to the location label with its edge aligned with the location label.
 Stick the Label (Protect) around the location label so that the location label is not torn off.

Fig. 3.11.5.1-12 Attachment of Location Labels

Table 3.11.5.1-5 Location Label List (DKU-00/10)

Connection Source (DKU-x0) Connection Destination (DKU-x0)
No. Part Name Location Label Color Part Name Location Label Color
UBX/SBX FBX Label  UBX/SBX FBX Label
1 SSWx00-1 SSWx00-1 CL1 0-1 White/Black SSWx01-1 SSWx00-1 CL1 1-0 White/Brown
2 SSWx02-1 SSWx01-1 CL1 2-1 White/Red SSWx03-1 SSWx01-1 CL1 3-0 White/Orange
3 SSWx04-1 SSWx02-1 CL1 4-1 White/Yellow SSWx05-1 SSWx02-1 CL1 5-0 White/Green
4 SSWx06-1 SSWx03-1 CL1 6-1 White/Blue SSWx07-1 SSWx03-1 CL1 7-0 White/Purple
5 SSWx01-2 SSWx00-2 CL2 1-1 Yellow/Brown SSWx00-2 SSWx00-2 CL2 0-0 Yellow/Black
6 SSWx03-2 SSWx01-2 CL2 3-1 Yellow/Orange SSWx02-2 SSWx01-2 CL2 2-0 Yellow/Red
7 SSWx05-2 SSWx02-2 CL2 5-1 Yellow/Green SSWx04-2 SSWx02-2 CL2 4-0 Yellow/Yellow
8 SSWx07-2 SSWx03-2 CL2 7-1 Yellow/Purple SSWx06-2 SSWx03-2 CL2 6-0 Yellow/Blue

INST03-11D-140
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-150

3-2 Connection of Cables

When the DKU-x0 is the UBX/SBX

a. Remove the caps from the cables to be connected.
b. Connect the cables to the SSWs in the DKU after checking “3.1.6 Notes when connecting
the DEV interface cable” (INST03-01-180). (Refer to Fig. 3.11.5.1-13 and Fig. 3.11.5.1-14.)

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

SSWx03-1

SSWx03-2
CL1 3-0

CL2 3-1
SSWx02-1

SSWx02-2
CL1 2-1

Rear View of CL2 2-0

DKU-x0 (UBX/SBX) SSWx01-1

SSWxyz-1 SSWxyz-2
SSWx01-2
-0 -1 -2 -0 -1 -2 CL1 1-0
Front View of SSW

Work before connecting CL2 1-1

the cables.
SSWx00-1

Cap SSWx00-2
CL1 0-1
Cable
CL2 0-0
Fig. 3.11.5.1-13 Connection of Cables (UBX/SBX_CC1_CL1/CL2_L)

INST03-11D-150
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-160

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

SSWx07-1

SSWx07-2
CL1 7-0

CL2 7-1
SSWx06-1

SSWx06-2
CL1 6-1

Rear View of
CL2 6-0
DKU-x0 (UBX/SBX)
SSWx05-1

SSWxyz-1 SSWxyz-2
SSWx05-2
-0 -1 -2 -0 -1 -2 CL1 5-0
Front View of SSW

Work before connecting

CL2 5-1
the cables.
SSWx04-1

Cap SSWx04-2
CL1 4-1
Cable
CL2 4-0
Fig. 3.11.5.1-14 Connection of Cables (UBX/SBX_CC1_CL1/CL2_U)

INST03-11D-160
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-170

When the DKU-x0 is the FBX

a. Remove the caps from the cables to be connected.
b. Connect the cables to the SSWs in the DKU after checking “3.1.6 Notes when connecting
the DEV interface cable” (INST03-01-180).

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

CL1 6-1
SSWx03-1

SSWx03-2

CL1 7-0

CL2 6-0
Rear View of CL1 4-1
DKU-x0 (FBX) CL2 7-1
SSWx02-1

SSWx02-2
SSWxyz-1 SSWxyz-2
CL1 5-0
-0 -1 -2 -0 -1 -2 -0 -1 -2 -0 -1 -2 CL2 4-0
Front View of SSW
CL1 2-1
CL2 5-1
SSWx01-1
Work before connecting
the cables.
SSWx01-2

CL1 3-0
Cap CL2 2-0
CL1 0-1
CL2 3-1
Cable
SSWx00-1

SSWx00-2

CL1 1-0
CL2 0-0

CL2 1-1
Fig. 3.11.5.1-15 Connection of Cables (FBX_CC1_CL1/CL2)

INST03-11D-170
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-180

4. Attachment of Cables
a. Route the eight cables in the cluster 1 and fix them with the loop cable ties. (Refer to Fig.
3.11.5.1-16 or Fig. 3.11.5.1-17.)

When the DKU-x0 is the UBX/SBX.

DKU-x0 (UBX/SBX)

Loop Cable Tie

Cable

DKC-x

Loop Cable Tie

Cable Duct

Rear View of
RACK-x0

Fig. 3.11.5.1-16 Fixation of Cables

(DKA-1PA – DKU-00 (UBX/SBX) or DKA-1PG – DKU-10 (UBX/SBX))

INST03-11D-180
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-190

When the DKU-x0 is the FBX.

DKU-x0 (FBX)
Loop Cable Tie

Cable

DKC-x

Loop Cable Tie

Cable Duct

Rear View of
RACK-x0

Fig. 3.11.5.1-17 Fixation of Cables

(DKA-1PA – DKU-00 (FBX) or DKA-1PG – DKU-10 (FBX))

INST03-11D-190
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-200

b. Route the eight cables in the cluster 2 and fix them with the loop cable ties. (Refer to Fig.
3.11.5.1-18 or Fig. 3.11.5.1-19.)

When the DKU-x0 is the UBX/SBX.

DKU-x0
(UBX/SBX)

Loop Cable Tie

Cable
DKC-x

Loop Cable Tie

Cable Duct

Rear View of
RACK-x0

Fig. 3.11.5.1-18 Fixation of Cables

(DKA-2PA – DKU-00 (UBX/SBX) or DKA-2PG – DKU-10 (UBX/SBX))

INST03-11D-200
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-210

When the DKU-x0 is the FBX.

DKU-x0
(FBX)

Loop Cable Tie

Cable
DKC-x

Loop Cable Tie

Cable Duct

Rear View of
RACK-x0

Fig. 3.11.5.1-19 Fixation of Cables

(DKA-2PA – DKU-00 (FBX) or DKA-2PG – DKU-10 (FBX))

INST03-11D-210
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-220

3.11.5.2 In the case of High-performance Model

To connect the DKA and DKU-00/10 in the high-performance model, the cable options shown in the
table below are required.

Table 3.11.5.2-1 Required Cable Options

No. Model Number Quantity Description
1 DKC-F810I-CC2 2 2m cable × 16

High-Performance Model

DKU-00/10
(UBX/SBX)

DKU-00/10
(FBX)

DKC-F810I-CC2 DKC-F810I-CC2
×2 ×2

DKA DKA DKA DKA

DKC-0/1 DKC-0/1
Rear View of Rear View of
Rack Rack

Fig. 3.11.5.2-1 Cable Routing

INST03-11D-220
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-230

1. Installation Procedure of Disk Adapter

NOTICE: Be sure to wear your wrist strap and attach to ground prior to performing the
following work. This will ensure that the IC and LSI on the PCB are protected
from static electricity.

1-1 Insertion of PCBs

a. Loosen the screws and remove the dummy plates. Refer to the Table 3.11.5.2-2 and Fig.
3.11.5.2-2.
NOTE: Store the removed dummy plates as they are required when the DKAs are removed.
b. Insert the PCBs to the correct locations in the DKC and tighten the screw.

Main Edge Connector

PCB NOTICE: • Check that the main edge connector of the PCB has
no deformation, damage or sticking of dust before
installing the PCB. (See INST03-01-80)
• When installing the PCB, hold the right and left of the
PCB with both hands, and insert it straight not to
contact the neighboring PCB.

Table 3.11.5.2-2 Inserting Location

DKC Addition No. Location No. Remarks
Cluster 1 Cluster 2
DKC-0 Basic DKA-1PA DKA-2PA
Option 1 DKA-1PB DKA-2PB
DKC-1 Option 2 DKA-1PG DKA-2PG
Option 3 DKA-1PH DKA-2PH

INST03-11D-230
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-240

1 1 2 2 1 1 2 2
P P P P P P P P
A B B A G H HG

Rear View of DKC-0 Rear View of DKC-1

DKC

DKA PCB

Lever Screw

Screw

Dummy Plate

Lever Screw
Screw
Fig. 3.11.5.2-2 Insertion of PCB

INST03-11D-240
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-250

2. Attachment of Device Interface Cable (CC2)

2-1 Attach the location labels to the cables.
a. Attach 16 location labels to 8 cables. Choose location labels from Labels (Address) and
Labels (Address) 2. See Fig. 3.11.5.2-3, Table 3.11.5.2-3, Table 3.11.5.2-4, Table 3.11.5.2-5
and Table 3.11.5.2-6.
b. Stick the Label (Protect) around the attached location labels.

Location Label  Location Label 

80mm 80mm

Cable
[Label Attachment Example]
Cable

Location Label

Edge

Label (Protect)

 Attach the location label to the MFC cable.

 Attach the Label (Protect) to the location label with its edge aligned with the location label.
 Stick the Label (Protect) around the location label so that the location label is not torn off.

Fig. 3.11.5.2-3 Attachment of Location Labels

Table 3.11.5.2-3 Location Label List (DKC-0 (DKA-1PA/2PA) – DKU-00)

No. Connection Source (DKC-0) Connection Destination (DKU-00)
Part Name Location Label Color Part Name Location Label Color
Label  UBX/SBX FBX Label
1 DKA-1PA CL1 1PA-0 White/Black SSW000-1 SSW000-1 CL1 0-0 White/Black
2 DKA-1PA CL1 1PA-1 White/Brown SSW002-1 SSW001-1 CL1 2-0 White/Red
3 DKA-1PA CL1 1PA-2 White/Red SSW004-1 SSW002-1 CL1 4-0 White/Yellow
4 DKA-1PA CL1 1PA-3 White/Orange SSW006-1 SSW003-1 CL1 6-0 White/Blue
5 DKA-2PA CL2 2PA-0 Yellow/Black SSW001-2 SSW000-2 CL2 1-0 Yellow/Brown
6 DKA-2PA CL2 2PA-1 Yellow/Brown SSW003-2 SSW001-2 CL2 3-0 Yellow/Orange
7 DKA-2PA CL2 2PA-2 Yellow/Red SSW005-2 SSW002-2 CL2 5-0 Yellow/Green
8 DKA-2PA CL2 2PA-3 Yellow/Orange SSW007-2 SSW003-2 CL2 7-0 Yellow/Purple

INST03-11D-250
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-260

Table 3.11.5.2-4 Location Label List (DKC-0 (DKA-1PB/2PB) – DKU-00)

No. Connection Source (DKC-0) Connection Destination (DKU-00)
Part Name Location Label Color Part Name Location Label Color
Label  UBX/SBX FBX Label
1 DKA-1PB CL1 1PB-0 White/Black SSW001-1 SSW000-1 CL1 1-0 White/Brown
2 DKA-1PB CL1 1PB-1 White/Brown SSW003-1 SSW001-1 CL1 3-0 White/Orange
3 DKA-1PB CL1 1PB-2 White/Red SSW005-1 SSW002-1 CL1 5-0 White/Green
4 DKA-1PB CL1 1PB-3 White/Orange SSW007-1 SSW003-1 CL1 7-0 White/Purple
5 DKA-2PB CL2 2PB-0 Yellow/Black SSW000-2 SSW000-2 CL2 0-0 Yellow/Black
6 DKA-2PB CL2 2PB-1 Yellow/Brown SSW002-2 SSW001-2 CL2 2-0 Yellow/Red
7 DKA-2PB CL2 2PB-2 Yellow/Red SSW004-2 SSW002-2 CL2 4-0 Yellow/Yellow
8 DKA-2PB CL2 2PB-3 Yellow/Orange SSW006-2 SSW003-2 CL2 6-0 Yellow/Blue

Table 3.11.5.2-5 Location Label List (DKC-1(DKA-1PG/2PG) – DKU-10)

No. Connection Source (DKC-1) Connection Destination (DKU-10)
Part Name Location Label Color Part Name Location Label Color
Label  UBX/SBX FBX Label
1 DKA-1PG CL1 1PG-0 White/Black SSW100-1 SSW100-1 CL1 0-0 White/Black
2 DKA-1PG CL1 1PG-1 White/Brown SSW102-1 SSW101-1 CL1 2-0 White/Red
3 DKA-1PG CL1 1PG-2 White/Red SSW104-1 SSW102-1 CL1 4-0 White/Yellow
4 DKA-1PG CL1 1PG-3 White/Orange SSW106-1 SSW103-1 CL1 6-0 White/Blue
5 DKA-2PG CL2 2PG-0 Yellow/Black SSW101-2 SSW100-2 CL2 1-0 Yellow/Brown
6 DKA-2PG CL2 2PG-1 Yellow/Brown SSW103-2 SSW101-2 CL2 3-0 Yellow/Orange
7 DKA-2PG CL2 2PG-2 Yellow/Red SSW105-2 SSW102-2 CL2 5-0 Yellow/Green
8 DKA-2PG CL2 2PG-3 Yellow/Orange SSW107-2 SSW103-2 CL2 7-0 Yellow/Purple

Table 3.11.5.2-6 Location Label List (DKC-1(DKA-1PH/2PH) – DKU-10)

No. Connection Source (DKC-1) Connection Destination (DKU-10)
Part Name Location Label Color Part Name Location Label Color
Label  UBX/SBX FBX Label
1 DKA-1PH CL1 1PH-0 White/Black SSW101-1 SSW100-1 CL1 1-0 White/Brown
2 DKA-1PH CL1 1PH-1 White/Brown SSW103-1 SSW101-1 CL1 3-0 White/Orange
3 DKA-1PH CL1 1PH-2 White/Red SSW105-1 SSW102-1 CL1 5-0 White/Green
4 DKA-1PH CL1 1PH-3 White/Orange SSW107-1 SSW103-1 CL1 7-0 White/Purple
5 DKA-2PH CL2 2PH-0 Yellow/Black SSW100-2 SSW100-2 CL2 0-0 Yellow/Black
6 DKA-2PH CL2 2PH-1 Yellow/Brown SSW102-2 SSW101-2 CL2 2-0 Yellow/Red
7 DKA-2PH CL2 2PH-2 Yellow/Red SSW104-2 SSW102-2 CL2 4-0 Yellow/Yellow
8 DKA-2PH CL2 2PH-3 Yellow/Orange SSW106-2 SSW103-2 CL2 6-0 Yellow/Blue

INST03-11D-260
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-270

2-2 Connection of Cables

In the case of cable installation between DKA-1PA/2PA and DKU-00

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.
a. Remove the caps from the cables to be connected.
b. Connect the cables to the DKA PCBs in the DKC-0 after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180).

DKAPCB DKA PCB

(DKA-1PA) (DKA-2PA)

CL1 1PA-0 CL2 2PA-0

CL1 1PA-1 CL2 2PA-1

CL1 1PA-2 CL2 2PA-2

CL1 1PA-3 CL2 2PA-3

Work before connecting
the cables.

Cap

Cable

Fig. 3.11.5.2-4 Connection of Cables

INST03-11D-270
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-280

When the DKU-00 is the UBX/SBX

c. Remove the caps from the cables to be connected.
d. Connect the eight cables to the SSWs in the DKU after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180). (Refer to Fig. 3.11.5.2-5 and Fig.
3.11.5.2-6.)

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-00 is the UBX/SBX.

SSW006-1

CL1 6-0

SSW004-1

CL1 4-0

Rear View of SSW002-1

DKU-00 (UBX/SBX)

SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 CL1 2-0
Front View of SSW

Work before connecting SSW000-1

the cables.

Cap CL1 0-0

Cable

Fig. 3.11.5.2-5 Connection of Cables (CC2_DKU-00 (UBX/SBX)_CL1)

INST03-11D-280
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-290

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-00 is the UBX/SBX.

SSW007-2

CL2 7-0

SSW005-2

Rear View of CL2 5-0

DKU-00 (UBX/SBX)

SSWxyz-1 SSWxyz-2 SSW003-2

-0 -1 -2 -0 -1 -2
Front View of SSW

Work before connecting CL2 3-0

the cables.

SSW001-2

Cap

Cable
CL2 1-0

Fig. 3.11.5.2-6 Connection of Cables (CC2_DKU-00 (UBX/SBX)_CL2)

INST03-11D-290
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-300

When the DKU-00 is the FBX

c. Remove the caps from the cables to be connected.
d. Connect the eight cables to the SSWs in the DKU after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180).

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-00 is the FBX.

CL1 6-0
SSW003-1

SSW003-2
CL2 7-0

CL1 4-0
Rear View of DKU-00 (FBX) SSW002-1

SSW002-2
CL2 5-0
SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 -0 -1 -2 -0 -1 -2
CL1 2-0
Front View of SSW SSW001-1

Work before connecting

the cables. SSW001-2
CL2 3-0

Cap CL1 0-0

SSW000-1
Cable
SSW000-2

CL2 1-0

Fig. 3.11.5.2-7 Connection of Cables (CC2_DKU-00 (FBX)_CL1/CL2)

INST03-11D-300
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-310

In the case of cable installation between DKA-1PB/2PB and DKU-00

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.
a. Remove the caps from the cables to be connected.
b. Connect the cables to the DKA PCBs in the DKC-0 after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180).

DKAPCB DKA PCB

(DKA-1PB) (DKA-2PB)

CL1 1PB-0 CL2 2PB-0

CL1 1PB-1 CL2 2PB-1

CL1 1PB-2 CL2 2PB-2

CL1 1PB-3 CL2 2PB-3

Work before connecting
the cables.

Cap

Cable

Fig. 3.11.5.2-8 Connection of Cables

INST03-11D-310
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-320

When the DKU-00 is the UBX/SBX

c. Remove the caps from the cables to be connected.
d. Connect the eight cables to the SSWs in the DKU after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180). (Refer to Fig. 3.11.5.2-9 and Fig.
3.11.5.2-10.)

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-00 is the UBX/SBX.

SSW007-1

CL1 7-0

SSW005-1

CL1 5-0

Rear View of SSW003-1

DKU-00 (UBX/SBX)

SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 CL1 3-0
Front View of SSW

Work before connecting SSW001-1

the cables.

Cap CL1 1-0

Cable

Fig. 3.11.5.2-9 Connection of Cables (CC2_DKU-00 (UBX/SBX)_CL1)

INST03-11D-320
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-330

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-00 is the UBX/SBX.

SSW006-2

CL2 6-0

SSW004-2

Rear View of CL2 4-0

DKU-00 (UBX/SBX)

SSWxyz-1 SSWxyz-2 SSW002-2

-0 -1 -2 -0 -1 -2
Front View of SSW

Work before connecting CL2 2-0

the cables.

SSW000-2

Cap

Cable
CL2 0-0

Fig. 3.11.5.2-10 Connection of Cables (CC2_DKU-00 (UBX/SBX)_CL2)

INST03-11D-330
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-340

When the DKU-00 is the FBX

c. Remove the caps from the cables to be connected.
d. Connect the eight cables to the SSWs in the DKU after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180).

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-00 is the FBX.

SSW003-1
CL1 7-0

SSW003-2

CL2 6-0

Rear View of DKU-00 (FBX) SSW002-1

CL1 5-0

SSW002-2
SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 -0 -1 -2 -0 -1 -2 CL2 4-0
Front View of SSW
SSW001-1
CL1 3-0

SSW001-2
Work before connecting
the cables.
CL2 2-0

SSW000-1
Cap
CL1 1-0

Cable SSW000-2

CL2 0-0
Fig. 3.11.5.2-11 Connection of Cables (CC2_DKU-00 (FBX)_CL1/CL2)

INST03-11D-340
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-350

In the case of cable installation between DKA-1PG/2PG and DKU-10

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.
a. Remove the caps from the cables to be connected.
b. Connect the cables to the DKA PCBs in the DKC-1 after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180).

DKAPCB DKA PCB

(DKA-1PG) (DKA-2PG)

CL1 1PG-0 CL2 2PG-0

CL1 1PG-1 CL2 2PG-1

CL1 1PG-2 CL2 2PG-2

CL1 1PG-3 CL2 2PG-3

Work before connecting
the cables.

Cap

Cable

Fig. 3.11.5.2-12 Connection of Cables

INST03-11D-350
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-360

When the DKU-10 is the UBX/SBX

c. Remove the caps from the cables to be connected.
d. Connect the eight cables to the SSWs in the DKU after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180). (Refer to Fig. 3.11.5.2-13 and Fig.
3.11.5.2-14.)

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-10 is the UBX/SBX.

SSW106-1

CL1 6-0

SSW104-1

CL1 4-0

Rear View of SSW102-1

DKU-10 (UBX/SBX)

SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 CL1 2-0
Front View of SSW

Work before connecting SSW100-1

the cables.

Cap CL1 0-0

Cable

Fig. 3.11.5.2-13 Connection of Cables (CC2_DKU-10 (UBX/SBX)_CL1)

INST03-11D-360
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-370

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-10 is the UBX/SBX.

SSW107-2

CL2 7-0

SSW105-2

Rear View of CL2 5-0

DKU-10 (UBX/SBX)

SSWxyz-1 SSWxyz-2 SSW103-2

-0 -1 -2 -0 -1 -2
Front View of SSW

Work before connecting CL2 3-0

the cables.

SSW101-2

Cap

Cable
CL2 1-0

Fig. 3.11.5.2-14 Connection of Cables (CC2_DKU-10 (UBX/SBX)_CL2)

INST03-11D-370
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-380

When the DKU-10 is the FBX

c. Remove the caps from the cables to be connected.
d. Connect the eight cables to the SSWs in the DKU after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180).

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-10 is the FBX.

CL1 6-0
SSW103-1

SSW103-2
CL2 7-0

Rear View of DKU-10 (FBX) CL1 4-0

SSW102-1

SSW102-2
SSWxyz-1 SSWxyz-2 CL2 5-0

-0 -1 -2 -0 -1 -2 -0 -1 -2 -0 -1 -2
Front View of SSW CL1 2-0
SSW101-1
Work before connecting
the cables.
SSW101-2
CL2 3-0

Cap
CL1 0-0
SSW100-1
Cable

SSW100-2

CL2 1-0

Fig. 3.11.5.2-15 Connection of Cables (CC2_DKU-10 (FBX)_CL1/CL2)

INST03-11D-380
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-390

In the case of cable installation between DKA-1PH/2PH and DKU-10

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.
a. Remove the caps from the cables to be connected.
b. Connect the cables to the DKA PCBs in the DKC-1 after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180).

DKAPCB DKA PCB

(DKA-1PH) (DKA-2PH)

CL1 1PH-0 CL2 2PH-0

CL1 1PH-1 CL2 2PH-1

CL1 1PH-2 CL2 2PH-2

CL1 1PH3 CL2 2PH-3

Work before connecting
the cables.

Cap

Cable

Fig. 3.11.5.2-16 Connection of Cables

INST03-11D-390
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-400

When the DKU-10 is the UBX/SBX

c. Remove the caps from the cables to be connected.
d. Connect the eight cables to the SSWs in the DKU after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180). (Refer to Fig. 3.11.5.2-17 and Fig.
3.11.5.2-18.)

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-10 is the UBX/SBX.

SSW107-1

CL1 7-0

SSW105-1

CL1 5-0

Rear View of SSW103-1

DKU-10 (UBX/SBX)

SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 CL1 3-0
Front View of SSW

Work before connecting SSW101-1

the cables.

Cap CL1 1-0

Cable

Fig. 3.11.5.2-17 Connection of Cables (CC2_DKU-10 (UBX/SBX)_CL1)

INST03-11D-400
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-410

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-10 is the UBX/SBX.

SSW106-2

CL2 6-0

SSW104-2

Rear View of CL2 4-0

DKU-10 (UBX/SBX)

SSWxyz-1 SSWxyz-2 SSW102-2

-0 -1 -2 -0 -1 -2
Front View of SSW

Work before connecting CL2 2-0

the cables.

SSW100-2

Cap

Cable
CL2 0-0

Fig. 3.11.5.2-18 Connection of Cables (CC2_DKU-10 (UBX/SBX)_CL2)

INST03-11D-410
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-420

When the DKU-10 is the FBX

c. Remove the caps from the cables to be connected.
d. Connect the eight cables to the SSWs in the DKU after checking “3.1.6 Notes when
connecting the DEV interface cable” (INST03-01-180).

CAUTION
A serious failure occurs if any of cables/connectors is wrongly connected.
Since a label bearing a connection destination is affixed on each cable/connector, work
very carefully referring to it and the wiring diagram.

When the DKU-10 is the FBX.

SSW103-1
CL1 7-0

SSW103-2

CL2 6-0
Rear View of DKU-10 (FBX) SSW102-1
CL1 5-0

SSW102-2
SSWxyz-1 SSWxyz-2

-0 -1 -2 -0 -1 -2 -0 -1 -2 -0 -1 -2 CL2 4-0
Front View of SSW
SSW101-1
CL1 3-0

SSW101-2
Work before connecting
the cables.
CL2 2-0

SSW100-1
Cap
CL1 1-0

Cable SSW100-2

CL2 0-0
Fig. 3.11.5.2-19 Connection of Cables (CC2_DKU-10 (FBX)_CL1/CL2)

INST03-11D-420
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-430

3. Attachment of Cables
a. Route the eight cables in the cluster 1 and fix them with the loop cable ties. (Refer to Fig.
3.11.5.2-20 or Fig. 3.11.5.2-21.)

When the DKU-x0 is the UBX/SBX.

DKU-x0 (UBX/SBX)

Loop Cable Tie

Cable (*1)
DKA DKC-x

Loop Cable Tie

Cable Duct

Rear View of
RACK-x0
*1: Pass the cables connected to the DKA-1PB or DKA-1PH into the
loop cable ties form upper side so that the DKA on the end side
can be inserted or extracted.

Fig. 3.11.5.2-20 Fixation of Cables (DKA-1PA/1PB – DKU-00 (UBX/SBX) or

DKA-1PG/1PH – DKU-10 (UBX/SBX))

INST03-11D-430
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-440

When the DKU-x0 is the FBX.

DKU-x0 (FBX)
Loop Cable Tie

Cable
(*1)
DKC-x
DKA

Loop Cable Tie

Cable Duct

Rear View of
RACK-x0

*1: Pass the cables connected to the DKA-1PB or DKA-1PH into the
loop cable ties form upper side so that the DKA on the end side
can be inserted or extracted.

Fig. 3.11.5.2-21 Fixation of Cables

(DKA-1PA/1PB – DKU-00 (FBX) or DKA-1PG/1PH – DKU-10 (FBX))

INST03-11D-440
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-450

b. Route the eight cables in the cluster 2 and fix them with the loop cable ties. (Refer to Fig.
3.11.5.2-22 or Fig. 3.11.5.2-23.)

When the DKU-x0 is the UBX/SBX

DKU-x0
(UBX/SBX)

Loop Cable Tie

(*1) Cable
DKC-x
DKA

Loop Cable Tie

Cable Duct

Rear View of
RACK-x0
*1: Pass the cables connected to the DKA-2PB or DKA-2PH into the
loop cable ties form upper side so that the DKA on the end side can
be inserted or extracted

Fig. 3.11.5.2-22 Fixation of Cables (DKA-2PA/2PB – DKU-00(UBX/SBX) or

DKA-2PG/2PH – DKU-10(UBX/SBX))

INST03-11D-450
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-11D-460

When the DKU-x0 is the FBX

DKU-x0
(FBX)

Loop Cable Tie

Cable
DKC-x (*1)
DKA

Loop Cable Tie

Cable Duct

Rear View of
RACK-x0

*1: Pass the cables connected to the DKA-2PB or DKA-2PH into the
loop cable ties form upper side so that the DKA on the end side can
be inserted or extracted.

Fig. 3.11.5.2-23 Fixation of Cables

(DKA-1PA/2PB – DKU-00 (FBX) or DKA-2PG/2PH – DKU-10 (FBX))

INST03-11D-460
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-10

3.12 Installation of Service Processor (DKC-F810I-SVP)

NOTICE: This work takes about three hours. During the work, the Web Console cannot
be used for some time because of a rebooting of the SVP PC and verification.
Inform the customer of the following before starting the addition.
 During this installation, customer cannot use Web Console/Storage
Navigator via a customer PC.
 When SNMP is being used:
• ‘cold start’ trap is reported several times.
• The obstacle trap which occurred during work may not be notified.
• SNMP command may not answer normally.
 The following SIMs may occur during this work, just complete them when
finished:
• BFE3F2 - SVP settings are duplicated
• BF86A3 - SVP RAS Switch#1 remains
• 7FF201 - Standby SVP failure detection
 When two or more sets of the DKC-F810I-MP are installed in the DKC810I-
CBXA (*1), the HUBBOX (DKC-F810I-HUB) is installed as well.

In this case, remove the HUBBOX and install the SVP redundant option to the
same mounting position as the HUBBOX. The removing the HUBBOX and
installing the SVP must be operated according to the additional installation
procedures.
In addition, instruct customer to store the removed HUBBOX as it will be
necessary when removing the SVP. (The DKC-1 (DKC-F810I-CBXB) of this
instruction is excluded.)

*1: The installation requirements of the HUBBOX are according

to the configuration of the DKC-F810I-MP in the SVP-OPTION/HUBBOX-01
Slot
DKC810I-CBXA.
(DKC-F810I-CBXB is excluded.)

Table 3.12-1 Installation Requirements of DKC-F810I-MP

and HUBBOX
Number of DKC-F810I- SVP-OPTION/HUBBOX-01 Slot
No. MP installed in Without SVP With SVP
DKC810I-CBXA Duplication Duplication
1 1 Free space SVP
2 2~3 HUBBOX SVP Rear View of
DKC810I-CBXA

INST03-12-10
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-20

Table 3.12-2 Parts List

No. Model Number Part Name Part No. Quantity Remarks
1 DKC-F810I-SVP SVP 5552759-A 1
EMI Core 5513535-1 1
2 DKC-F810I-HUB HUBBOX 5552760-A 1

INST03-12-20
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-30

3.12.1 Installation Procedure of Service Processor (DKC-F810I-SVP)

3.12.1.1 Installation Procedure
1. Operating the Basic SVP
1-1 Connecting the Maintenance PC to the SVP

(1)
Connect the Maintenance PC to the Basic SVP using SVP Connect Utility.

The login user is different by the presence of the microprogram.

[Connected to]
The Basic SVP xxx.xxx.xxx.15 in the storage system concerned

INST03-12-30
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-40

1-2 Config Backup

(1) <Mode change>
Change the mode to [Modify Mode].

(2)
Select (CL) [Install] in the ‘SVP’ window and select (CL) [Copy Config Files] in the
‘Install’.

(3)
Select (CL) [Create Configuration Backup] in the ‘Copy
Config Files’.

(4)
Execute an operation for backing up the
configuration information.
Prepare the removable media for backup
and insert the media.
Please select (CL) the [Refresh] button,
and update drive information.
Select (CL) the drive and the PC in which
the media was inserted. Select (CL) the
[OK] button.

NOTE: For the procedure of backing up

the configuration information to
a CD-R, see page MICRO07-190.

INST03-12-40
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-50

(5)
When you want to continue the process,
select the [Yes] button. When the backup
to the Config media is not necessary,
select the [No] button.

(6)
Backup the configuration information to the
Config media for backup. While this
operation is being done, the ‘CNFCPY
Wait...’ window is displayed.

(7)
After the Config media is pulled out, select (CL)
the [OK] in response to the message “Please
remove the Config media.”.

(8)
Select (CL) [Exit] of the ‘Copy Config Files’ to finish this operation.

INST03-12-50
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-60

1-3 Setting of SVP Installation

(1) <Start [Install]>
Select (CL) [Install] from ‘SVP’.

(2) <Select [Change Configuration]>

Select (CL) [Change Configuration] from
‘Install’.

(3) <Select [Installation]>

Select (CL) [Installation] from ‘Menu
Dialog’, and select (CL) [OK] button.

(4) <Select a part to be changed>

Select (CL) [SVP], and select (CL) [OK]
button.

INST03-12-60
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-70

(5) <Wear a wrist strap>

Select (CL) [OK] in response to “To
prevent serious failures caused by the
static electrical charge, be sure to wear a
wrist strap on your wrist and connect the
earth clip attached on the other side of the
wrist strap to the chassis frame (metal
part) before starting operation.”.

(5)-1 <Confirm wearing wrist strap>

In response to a message, “Did you put on
a wrist strap on your wrist?”.
Select [Yes] when wrist strap is on your
wrist.
Select [No] when there is no wrist strap on
your wrist.
When [No] is selected (CL), go to Step (5)-
2.

(5)-2
In response to a message, “This operation
cannot be excuted, because the wrist strap
has not been worn. Do you want to stop
this process?
[Yes]: This processing will be stopped.
[No]: This confirming message will
appear.”
When [Yes] is selected (CL), the routine
is returned to Step (2) on page INST03-12-60.
When [No] is selected (CL), returned to Step (5).

(6) <Start Installation>

Select (CL) [Yes] button in response to
“The SVP will be installed. Do you want
to continue?”.
Select (CL) [No] button. Return to Step
(2).

INST03-12-70
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-80

(7) <Confirmation message>

If there is not the HUBBOX, go to Step
(13).

If there is the HUBBOX, “The HUBBOX

is required to be removed. Do you want to
continue?” message is displayed.

Select (CL) [Yes] button. Go to Step (8).

Select (CL) [No] button. Return to Step (2).

(8) <Check shut down LED>

“Is the LED to be removed turned on?”
message is displayed.

If the Shut down LED is on, select (CL) [Yes]

button and go to Step (10).
If the Shut down LED is off, select (CL) [No]
button and go to Step (9).

(9) <Removal of the HUBBOX>

“Check the location of the HUBBOX and
remove it. (HUBBOX-xx) After the
operation has completed, select [OK].”
message is displayed.
Go to Step (11).

(10) <Removal of the HUBBOX>

“Remove the hardware from the removed
part (HUBBOX(HUBBOX-nn) with the
LED on). After the operation has
completed, select [OK].” message is
displayed.
Go to Step (11).

INST03-12-80
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-90

(11) <De-Installation Procedure of Additional HUB>

a. Loosen the two screws and remove the HUBBOX.

HUBBOX-01

Rear View of DKC-0 Rear View of

DKC

HUBBOX

Lever

Screw

Lever
Screw
Top
Side

Bottom Front View of HUBBOX

Side

Fig. 3.12.1.1-1 Removal of HUBBOX

INST03-12-90
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-100

(12) <Removal of the HUBBOX>

After remove the HUBBOX, select (CL)
[OK].

(13) <Installation of SVP>

“Install the additional SVP. After the
operation has completed, select [OK].”
message is displayed.

INST03-12-100
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-110

2. Installation Procedure of Service Processor

2-1 Installation of SVP
(1) When removing the dummy plates from the SVP-OPTION slot is required, loosen the two
screws and remove the dummy plate.
When removing the dummy plates from the SVP-OPTION slot is unnecessary, go to the
Step (2).

SVP-OPTION

Rear View of DKC-0

Rear View of
DKC

Screw

Dummy Plate

Screw
Fig. 3.12.1.1-2 Removal of Dummy Plate

INST03-12-110
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-120

(2) Loosen the screw and rotate the cover on the SVP-OPTION upward. Then, tighten the
screw.
(3) Set the SVP RAS Switch #1 on the SVP-OPTION to ON (lower position).
Use something sharp (eg. a pen or a mini screwdriver etc.) when set the SVP RAS Switch
#1.
(4) Install the SVP and fasten the two screws.
NOTICE: Confirm the vertical direction of the SVP. If the direction is wrong, the SVP will
not be ON.

SVP-OPTION Top Side Screw Cover

SVP-BASIC

Front View of SVP

Bottom Side

SVP RAS Switch #1

(SVP PS ON/OFF INH ON
Rear View of DKC-0 Switch)

Rear View of
DKC-0

SVP

Lever

Screw

Lever

Screw

Fig. 3.12.1.1-3 Installation of SVP

INST03-12-120
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-130

2-2 Storage of Dummy Plate

(1) When there are removed dummy plates, loosen the three screws  on the front side of the
DKC and remove the cable cover.
When there are no removed dummy plates, go to the Step 2-3.
(2) Loosen the screw  and remove the accessory box.
(3) Put the removed dummy plate in the accessory box.
(4) Put the accessory box in place and fix it with the screw .
(5) Put the cable cover in place and fix it with the three screws .

Front View of DKC

Dummy Plate

DKC

Accessory Box

Screw 
Front View Screw 

Screw 

Cable Cover

Fig. 3.12.1.1-4 Storage of Dummy Plate

INST03-12-130
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-140

3. Operating the Basic SVP

3-1 <Confirmation of the SVP installation>
After the Installation of SVP, select (CL)
[OK].

3-2 <Operation of after the SVP installation>

“After the operation has completed, set the
additional SVP. After setting the additional
SVP, select [OK].” message is displayed.

INST03-12-140
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-150

4. Operating the Additional SVP

4-1 Connecting the Maintenance PC
Connect the Maintenance PC to the SVP has been installed using the utility for connection.

The login user is different by the presence of the microprogram.

[Connected to] Additional SVP 126.255.254.15

NOTE: When the IP address of the Maintenance PC is not 126.xxx.xxx.13, change the IP
address of the Maintenance PC to 126.255.254.13 once, and then connect it to SVP.

In this section, using two user type to connect with the SVP. If you don’t know the password,
please contact with the technical support division. When there is no description, using
“Installed User”.

After you input a user name and the password, input “Maintenance Password”. If you don’t
know the “Maintenance Password”, please contact with the technical support division.

INST03-12-150
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-160

4-2 Setting the Data and Time

<Making sure of the setting of a time zone>
(1) Open the ‘Control Panel’ window.
Select (DR) [Control Panel] from the [Start]
menu.

(2) Open the ‘Date and Time’ window.

Select (DC) [Date and Time] in the
‘Control Panel’ window.

INST03-12-160
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-170

(3) Select [Change time zone].

Select (CL) [Change time zone...].

(4) Make sure of the setting of the [Time Zone Settings].

Make sure that the ‘Time Zone Settings’
is set as “(UTC) Coordinated Universal
Time” irrespective of a place where the
storage system is installed.

(5) <Set the [Date and Time Settings]>

Select (CL) [Change date and time...].
Check if the ‘Date and Time Settings’ is set to
the current time and date.
If not, reset it correctly. Then, select (CL)
[OK].

(6) Close the ‘Control Panel’ window.

Select (DR) [File] and [Close] in this order in the ‘Control Panel’ window.

INST03-12-170
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-180

4-3 <Installing the Microprogram>

4-3-1 Preparation
When the Microprogram has already been
installed (when “Wait for the start of Storage
Management Service” is displayed in desktop
window) in the Additional SVP, perform the
following operations. When the
Microprogram is not installed, go to 4-3-2.
 Perform uninstalling Apache program.
(Go to 4-3-1-1 Uninstalling Apache)
 Perform uninstalling Tomcat program. (Go to 4-3-1-2 Uninstalling Tomcat program)
 Perform uninstalling Java program. (Go to 4-3-1-3 Uninstalling Java program)
 Perform uninstalling Perl program. (Go to 4-3-1-4 Uninstalling Perl program)
 Perform uninstalling Flash Player program. (Go to 4-3-1-5 Uninstalling Flash Player
program)

INST03-12-180
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-190

4-3-1-1 Uninstalling Apache

(1) Mount the OSS media
Insert the OSS media (the second media) to the CD-ROM drive in the Maintenance PC.

(2) Launch the Command Prompt as administrator

Select (DR) [Start]-[All Programs]-[Accessories], and
launch the Command Prompt with ‘Run as administrator’
in right-click menu.

(3) Launch the uninstallation batch

Enter
“\\tsclient\e\JavaAp\Apache\ApacheUnIn
st.bat” into the Command Prompt, and
press the Enter key.

At the end of this process, the Command

Prompt will close automatically.

NOTE: The input value is the form of

“\\tsclient\<drive letter>\JavaAp\Apache\ApacheUnInst.bat”.
A drive letter is made the drive which inserted the OSS media.
The above is a case where the CD-ROM drive is assigned a drive letter E.

(4) Take out the OSS media

Take out the OSS media (the second media) from the CD-ROM drive in the Maintenance
PC.

INST03-12-190
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-200

4-3-1-2 Uninstalling Tomcat program

(1)
Select (DR) [Start]-[Control Panel].

(2)
Select (DC) [Programs and Features].

(3)
Select (CL) [Apache Tomcat 7.0 Tomcat7
(remove only)], and select (CL)
[Uninstall/Change].
If there is no [Apache Tomcat 7.0
Tomcat7 (remove only)] in the list, go to
4-3-1-3.

INST03-12-200
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-210

(4)
Select (CL) [Uninstall].

(5)
If the following message box is displayed,
select (CL) [Yes].

If “Note: C:\Program Files (x86)\Apache

Software Foundation\Tomcat 7.0 could
not be removed.” is displayed, select (CL)
[OK].

(6)
When “Uninstallation Complete”
dialogue box is displayed, select (CL)
[Close].

INST03-12-210
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-220

(7)
[Apache Tomcat 7.0 Tomcat7 (remove
only)] in ‘Programs and Features’
window was deleted.
Close the window.

NOTICE: Until procedure 4-3-1-3 is finished, please don’t logout or shutdown SVP.
If you do them, SVP may no longer work properly. If a shutdown request
message is displayed, please don’t shutdown.

INST03-12-220
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-230

4-3-1-3 Uninstalling Java program

(1)
Select (DR) [Start]-[Control Panel] in this order.

(2)
Select (DC) [Programs and Features].

(3)
Select [Java SE Development Kit 7
Update 21], and then select (CL)
[Uninstall].
If there is no [Java SE Development Kit 7
Update 21] in the list, go to (8).

INST03-12-230
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-240

(4)
A message, “Are you sure you want to
uninstall Java SE Development Kit 7
Update 21?” is displayed.
Select (CL) [Yes].

(5)
Uninstallation of Java is started.

(6)
When the window to require rebooting the system is displayed, select (CL) [No]. (*1)
When this window is not displayed, go to Step (7).

NOTE: Don’t select [Yes]. If you do them, SVP may no longer work properly.
*1: If selecting (CL) [Yes], SVP will be rebooted. In this case, follow the procedures below.
• Login to SVP after rebooting.
Refer to “4-1. Connecting the Maintenance PC” (INST03-12-150) to choose login user
name.
• When following messages are displayed, select (CL) [OK].
“Unable to log into the SVP, because there is a problem with its system requirements.
Reboot it, and then reconfigure the SVP.”
• Continue procedures (8) after SVP rebooting.
Refer to “4-1. Connecting the Maintenance PC” (INST03-12-150). Please use
“Preinstalled User”.

INST03-12-240
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-250

(7)
The [Java SE Development Kit 7 Update
21] is deleted from the ‘Programs and
Features’ window.
Close the window by selecting (CL) the
[] button.

(8)
Select (DR) [Start]-[Control Panel] in this order.

(9)
Select (DC) [Programs and Features].

INST03-12-250
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-260

(10)
Select [Java 7 Update 21], and then select
(CL) [Uninstall].
If there is no [Java 7 Update 21] in the
list, go to 4-3-1-4.

(11)
A message, “Are you sure you want to
uninstall Java 7 Update 21?” is displayed.
Select (CL) [Yes].

(12)
Uninstallation of Java is started.

(13)
If the following message box is displayed,
select (CL) [Close Programs and
Continue].

If the message, “Save your work and

data! Then click OK to close your
programs and complete the Java update.”
is displayed, select (CL) [OK].

INST03-12-260
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-270

(14)
When the window to require rebooting the system is displayed, select (CL) [No]. (*1)
When this window is not displayed, go to Step (15).

NOTE: In several minutes, it may reboot automatically.

*1: If selecting (CL) [Yes] or automatically, SVP will be rebooted. In this case, follow the
procedures below.
• Login to SVP after rebooting.
Refer to “4-1. Connecting the Maintenance PC” (INST03-12-150) to choose login user
name.
• When following messages are displayed, select (CL) [OK].
“Unable to log into the SVP, because there is a problem with its system requirements.
Reboot it, and then reconfigure the SVP.”
• Continue procedures 4-3-1-5 after SVP rebooting.
Refer to “4-1. Connecting the Maintenance PC” (INST03-12-150). Please use
“Preinstalled User”.

(15)
The [Java 7 Update 21] is deleted from
the ‘Programs and Features’ window.
Close the window by selecting (CL) the
[] button.

INST03-12-270
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-280

4-3-1-4 Uninstalling Perl program

(1)
Select (DR) [Start]-[Control Panel] in this order.

(2)
Select (DC) [Programs and Features].

(3)
Select [ActivePerl 5.16.2 Build 1602 (64-
bit)], and then select (CL) [Uninstall].
If there is no [ActivePerl 5.16.2 Build
1602 (64-bit)] in the list, go to 4-3-1-6.

INST03-12-280
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-290

(4)
A message, “Are you sure you want to
uninstall ActivePerl 5.16.2 Build 1602
(64-bit)?” is displayed.
Select (CL) [Yes].

(5)
Uninstallation of Perl is started.

(6)
The [ActivePerl 5.16.2 Build 1602 (64-
bit)] is deleted from the ‘Programs and
Features’ window.
Close the window by selecting (CL) the
[] button.

INST03-12-290
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-300

4-3-1-5 Uninstalling Flash Player program

(1)
Select (DR) [Start]-[Control Panel] in this order.

(2)
Select (DC) [Programs and Features].

(3)
Select [Adobe Flash Player 11 ActiveX],
and then select (CL) [Uninstall].
If there is no [Adobe Flash Player 11
ActiveX] in the list, go to 4-3-2.

INST03-12-300
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-310

(4) Starting uninstallation

Select (CL) [UNINSTALL].

(5) Finishing application

If some applications were using Flash
Player, the application name is displayed.
Please finish the applications.

(6) Finishing uninstallation

Select (CL) [DONE].

(7)
The [Adobe Flash Player 11 ActiveX] is
deleted from the ‘Programs and Features’
window.
Close the window by selecting (CL) the
[] button.

INST03-12-310
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-320

4-3-2 <Starting Installation>

 Insert a micro program media in the CD-ROM drive of Maintenance PC and wait for one
minutes or so.
 Select (DR) [All Programs]-[Accessories]-[Run] from [Start] menu on SVP. Enter
“\\tsclient\E\setup.exe” and select (CL) the [OK] button.

NOTE1: Select the drive which inserted a CD-R in .

“\\tsclient\E\setup.exe”
Input the drive name of the CD-ROM drive of
Maintenance PC.
Indicate Maintenance PC. (This spelling is inputted.)

NOTE2: When the SVP is running, the

message “Initializing the SVP that is
currently operating. Do you want to
continue?” is displayed. Select (CL)
[Yes].

The window to reboot the SVP is

displayed. Select (CL) [Finish] after
check “Yes” in radio buttons.
After waiting for about five minutes,
install the microprogram again from
4-3-2  after rebooting the SVP.
Refer to “4-1 Connecting the
Maintenance PC” (INST03-12-150).
Please use “Preinstalled User” to
connect with SVP.

“The publisher could not be verified.

Are you sure you want to run this
software?” is displayed. Select (CL)
[Yes].

INST03-12-320
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-330

4-4 <Using another media>

4-4-1 <Installing the Configuration Information>
(1)
Prepare the Config media which did backup.

(2)
Select (CL) [Backup Config Media] in the
‘Select Setup Config’ window and select
(CL) the [OK] button.

INST03-12-330
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-340

(3)
Select the drive which insert the Backup
Config Media (prepared with Step (1)),
and select (CL) the [OK] button.

Select (CL) [Refresh] button, Disk is

updated to the latest information.

(4)
Perform copy processing of the configuration
information from the Backup Config Media to
the SVP.
The ‘CNFCPY Wait...’ window is displayed
during this time.

(5)
Select (CL) the [OK] button after
removing the configuration information
media.

INST03-12-340
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-350

4-4-2 <Installing the RAID Manager>

(1)
Select (CL) [Next>].

(2)
Select (CL) [Next>].

(3)
Select (CL) [Finish].

INST03-12-350
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-360

4-4-3 <Installing the OSS media>

(1)
When the message of “Insert the second CD-R.” is
displayed, replace it to the second media. Select (CL)
[OK] after the replacement.

INST03-12-360
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-370

4-5 Setting Up of JAVA

Perform setting up operation of Java.
When JAVA has already been installed, go to Section 4-6.

(1)
Select (CL) [Next>].

(2)
Select (CL) [Next>].

(3)
Copying of the file is started.

INST03-12-370
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-380

(4)
Select (CL) [Next>].

(5)
Installation is started.

(6)
Select (CL) [Close].
If [Register your JDK] window opens,
close it.

INST03-12-380
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-390

(7)
When the window to require rebooting the system is displayed, select (CL) [No].
When this window is not displayed, go to 4-6.

NOTE: Do not select [Yes]. If you do, it may cause a SVP failure.

NOTE: Do not logout or shutdown SVP until SVP is rebooted in 4-10.

If you do, it may cause a SVP failure.

4-6 The Setting of Apache SSL communication

The things of default are set in the key creation for SSL communication and the certificate file.
When you install an SSL communication key and a certificate file responding to the customer’s
request, see “Hitachi Device Manager - Storage Navigator User Guide”.
It advances to Step 4-7 when setting it by default.

INST03-12-390
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-400

4-7 Setting Up of Perl

Perform setting up operation of Perl.
When Perl has already been installed, go to Section 4-8.

(1)
Select (CL) [Next>].

(2)
After selecting “I accept the terms in the
License Agreement”, select (CL) [Next>].

(3)
Select (CL) [Next>].

INST03-12-400
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-410

(4)
Select (CL) [Next>].

(5)
Select (CL) [Install].
Copying of the file is started.

(6)
When the copying of the file is
completed, this window is displayed.
Remove the check mark from the left side
check box of the “Display the release
notes” and select (CL) [Finish].

INST03-12-410
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-420

4-8 Setting Up of Tomcat

Perform setting up operation of Tomcat.
When Tomcat has already been installed, go to 4-9.

(1)
Select (CL) [Next>].

(2)
Select (CL) [I Agree].

(3)
Select (CL) [Next>].

INST03-12-420
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-430

(4)
Select (CL) [Next>].

(5)
Select (CL) [Next>].

(6)
Select (CL) [Install].

If the message, “The specified installation

directory is not empty. Do you wish to
continue?” is displayed, select (CL) [OK].

INST03-12-430
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-440

(7)
Wait while installing.

(8)
Uncheck all the checkboxes, and select
(CL) [Finish].

INST03-12-440
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-450

4-9 Setting Up of Flash Player

Perform setting up operation of Flash Player.
When Flash Player has already been installed, go to Section 4-10.

(1) Starting installation

Select (CL) [I have read and agree to the
terms of the Flash Player License
Agreement.], and select (CL)
[INSTALL].

(2) Finishing installation

After installation is finished, select (CL)
[Never check for updates (not
recommended)], and select (CL) [DONE].

INST03-12-450
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-460

4-10 <Rebooting the SVP>

When the setting up is completed, remove the
CD-ROM and select (CL) [Finish].
The SVP automatically restarts. When it
reboots, the connection between the
Maintenance PC and the Additional SVP is
cut off. Wait for about five minutes, and then
reconnect the Maintenance PC to the
Additional SVP.

[Connected to]
The Additional SVP 126.255.254.15

INST03-12-460
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-470

4-11 <Setting an IP Address and Duplication of Additional SVP>

(1) <Starting SVP program>
<When Web Console isn’t working>
Select (CL) [Start SVP].

<When Web Console is working>

Select (CL) [Maintenance]-
[Maintenance Components
(General)].

(2) <Mode change>

Select (CL) the [View Mode] of SVP
main screen. When it becomes [Modify
Mode (Unlocked)] and the next message
is displayed, select (CL) the [OK] button
and go to Step (3).
“The available maintenance operations
are limited due to lock process failure.
If you want to make all the maintenance
operations operable, check that the communication error has not occurred between SVP
and DKC, and then retry the operation. If this status is still unrecoverable, reboot the
SVP.”.

Select (CL) the [View Mode] of the SVP main screen. When it becomes to [Modify Mode]
from [View Mode] too, select (CL) the [OK] button and go to Step (3).

(3) <Opening the Install window>

Select (CL) [Install] from the [SVP] menu.

INST03-12-470
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-480

(4) <Selecting [Set SVP IP Address]>

Select (CL) [Set IP Address] in the
‘Install’ window.

NOTE: Although it may be an error display if the Web Server Status window is displayed
before the IP address setting work of SVP is completed, there is no problem
because it is the one by the process of the SVP replacement.

INST03-12-480
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-490

(5) <Verifying an IP address>

Select (CL) [SVP] in the Internal IP
Address, and check if the IP Address and
the Subnet Mask of the Internal IP
Address are setup correctly.

(6) <Setting the SVP duplication>

(a) Check (CL) [Use Duplex SVP] in the
External IP address box.
(b) Select (CL) [Standby SVP] in the
SVP Kind box.
(c) Enter the IP addresses and subnet
masks of the Master and Standby
SVPs, and then select (CL) [OK].

NOTE: You do not have to enter the

information of Item (c) above
when the setting of the external
IP address is not required.
Go to Step (8).
NOTE: When the Service Processor is installed, information transmission to Standby SVP
is performed once per a day. The Standby SVP reboots for the application after
the information transfer. Even if a Standby SVP does not have setting of
periodical reboot, Standby SVP reboots. For example, Standby SVP reboots at
around 13:30 with the equipment which transmits at 13:00. The time of a reboot
changes by transfer information quantity.

INST03-12-490
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-500

(7) <Confirming the external IP address setting>

When a message, “When there are
directions to set the external IP address,
please set the external IP address from the
“Control Panel” of Windows after
performing this operation,” is displayed,
select (CL) the [OK] button.

(8) <Inserting the media containing the configuration information>

Select (CL) the [Cancel] button.

(9) <Confirming rebooting of the SVP>

Select (CL) [OK] in response to a message, “This will
reboot SVP.”

When the setting up is completed, the SVP reboots

automatically. When it reboots, the connection between
the Maintenance PC and the Additional SVP is cut off.
Wait for about five minutes, and then reconnect the
Maintenance PC to the Additional SVP.

[Connected to]
The IP Address xxx.xxx.xxx.14 which is setup in the Additional SVP by Step 4-11 (5) in
the storage system concerned.

NOTE: When the IP address of the Maintenance PC is changed in “4-1 Connecting the
Maintenance PC”, return the IP address of the Maintenance PC to xxx.xxx.xxx.13,
and then connect it to SVP.

INST03-12-500
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-510

4-12 <Setting an external IP address>

When the setting of the external IP address is not required, go to Step 5.

(1)
(a) <Opening the Control Panel window>
Select (DR) [Control Panel] from the [Start] menu.

(b) <Opening the Network and Sharing Center window>

Select (CL) [Network and Sharing
Center] in the ‘Control Panel’
window.

(c) <Opening the Network Connections window>

Select (CL) [Change adapter settings]
in the ‘Network and Sharing Center’
window.

(d) <Opening the Public LAN Properties window>

Select (CL) [Public LAN] in the
‘Network Connections’ window and
select (CL) [Properties] by clicking
the right mouse button.

INST03-12-510
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-520

(e)
Select (CL) [Internet Protocol Version 4
(TCP/IPv4)] in the ‘Local Area Connection
Properties’ window and select (CL) the [Properties]
button.

(f) <Setting the external IP address>

Set the “IP address”, “Subnet mask”, “Default
gateway”, “Preferred DNS server” and
“Alternate DNS server” and select (CL) the
[OK] button.
When you do not set IPv6, go to Step (i).

(g)
Select (CL) [Internet Protocol Version 6
(TCP/IPv6)] in the ‘Local Area Connection
Properties’ window and select (CL) the [Properties]
button.

INST03-12-520
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-530

(h) <Setting the external IP address>

Set the “IPv6 address”, “Subnet
prefix length”, “Default gateway”,
“Preferred DNS server”, “Alternate
DNS server” and select (CL) the
[OK] button.

(i)
After the setting is completed, select (CL) the [OK] button in the “Local Area
Connection Properties” window.
Close the ‘Network Connections’ window.

4-13 <Setting Web Console>

Make a setting of the WEB CONSOLE (WEB CONSOLE SECTION “1. Before using Web
Console ”). (WEB01-10)

4-14 <Erasing logs>

Erase all logs that were made during operation of the SVP. (SVP02-03-10)

INST03-12-530
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-540

5. Operating the Basic SVP

Operate the basic SVP as follows.

5-1 Connecting the Maintenance PC

Connect the Maintenance PC to the Basic SVP.

The login user is different by the presence of the microprogram.

[Connected to]
The Basic SVP xxx.xxx.xxx.15 in the storage system concerned

5-2
(1) <Operation of SVP installation>
Select (CL) [OK] button, in response to
“After the operation has completed, set the
additional SVP. After setting the additional
SVP, select [OK].”

INST03-12-540
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-550

(2) <Setting the SVP duplication>

(a) Check (CL) [Use Duplex SVP] in the
External IP Address box.
(b) Select (CL) [Master SVP] in the SVP
Kind box.
(c) Enter the IP addresses and subnet masks
of the Master and Standby SVPs, and then
select (CL) [OK].

*1: You do not have to enter the information

of Item (c) above when the setting of the
external IP address is not required.
Go to Step (4).

(3) <Confirming the external IP address setting>

When a message, “When there are directions
to set the external IP address, please set the
external IP address from the “Control Panel”
of Windows after performing this operation,”
is displayed, select (CL) the [OK] button.

(4) <Inserting the media containing the configuration information>

Execute an operation for backing up the
configuration information.
Prepare the removable media for backup and
insert the media.
Please select (CL) the [Refresh] button, and
update drive information.
Select (CL) the drive and the PC in which the
media was inserted. Select (CL) the [OK]
button.
NOTE: For the procedure of backing up the
configuration information to a CD-R,
see page MICRO07-190.

INST03-12-550
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-560

(5) <Confirming the configuration information backup>

When you want to continue the process, select
(CL) the [Yes] button.
When the backup to the Config media is not
necessary, select (CL) the [No] button.

(6) <Taking out the Config media>

When this procedure is completed, the message
“Please remove the Config media.” is displayed.
Remove the configuration information media,
select (CL) [OK].

(7) <Confirming rebooting of the SVP>

Select (CL) [OK].

When the SVP reboots, the connection between the

Maintenance PC and the Basic SVP is cut off. Wait for about
five minutes, and then reconnect the Maintenance PC to the
Basic SVP.

[Connected to]
The Basic SVP xxx.xxx.xxx.15 in the storage system concerned

INST03-12-560
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-570

5-3 <Setting an external IP address>

When the setting of the external IP address is not required, go to Step 6.

(1)
(a) <Opening the Control Panel window>
Select (DR) [Control Panel] from the [Start] menu.

(b) <Opening the Network and Sharing Center window>

Select (CL) [Network and Sharing
Center] in the ‘Control Panel’
window.

(c) <Opening the Network connections window>

Select (CL) [Change adapter settings]
in the ‘Network and Sharing Center’
window.

(d) <Opening the Public LAN Properties window>

Select (CL) [Public LAN] in the
‘Network Connections’ window and
select (CL) [Properties] by clicking
the right mouse button.
When you do not set IPv4, go to Step
(g).

INST03-12-570
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-580

(e)
Select (CL) [Internet Protocol Version 4
(TCP/IPv4)] in the ‘Local Area Connection
Properties’ window and select (CL) the [Properties]
button.

(f) <Setting the external IP address>

Set the “IP address”, “Subnet mask”, “Default
gateway”, “Preferred DNS server” and
“Alternate DNS server” and select (CL) the
[OK] button.
When you do not set IPv6, go to Step (i).

(g)
Select (CL) [Internet Protocol Version 6
(TCP/IPv6)] in the ‘Local Area Connection
Properties’ window and select (CL) the [Properties]
button.

INST03-12-580
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-590

(h) <Setting the external IP address>

Set the “IPv6 address”, “Subnet
prefix length”, “Default gateway”,
“Preferred DNS server”, “Alternate
DNS server” and select (CL) the
[OK] button.

(i)
After the setting is completed, select (CL) the [Close] button(In case of no change of
IP address, select (CL) [OK] button) in the “Public LAN Properties” window.
Close the ‘Network connections’ window.

INST03-12-590
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-600

6. Executing SSVP Reset

a. Loosen the screw, and remove the jumper cover from the DKCPANEL.
DKC
PANEL- DKCPANEL

Front View of DKC-0

Screw
Jumper Cover

Fig. 3.12.1.1-5 Removal of Jumper Cover

b. Insert the maintenance jumper into SSVP ALARM RESET jumper (JP3) on the
DKCPANEL. And then, remove the maintenance jumper. Confirm that four SSVP
STATUSLED of DKCPANEL turns on and turns off the light.
c. Attach the jumper cover to the DKCPANEL, and tighten the screw.

Front View of DKCPANEL

Maintenance JP3
Jumper

SSVP ALARM
RESET Jumper

JP3 SSVP STATUS LED

Fig. 3.12.1.1-6 Location of SSVP ALARM RESET Jumper

d. Set the SVP RAS Switch #1 on the SVP-OPTION to OFF (upper position). (Refer to Fig.
3.12.1.1-3.)
e. Loosen the screw and put the cover on the SVP back in place. Then, tighten the screw.
INST03-12-600
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-610

3.12.1.2 Confirmation Procedure

1. Verifying the LED
Make sure that statuses of LEDs on the SVP-BASIC and SVP-OPTION are those shown in the
figure below in a lighting part.

SVP-OPTION
SVP-BASIC

Rear View of DKC-0

LED

Front View of SVP

SVP-BASIC SVP-OPTION

Light Light

Fig. 3.12.1.2-1 Confirmation of LEDs

INST03-12-610
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-620

2. Operating the Basic SVP

NOTE: This operation needs that Standby SVP is a [View mode].

(1) Connecting the Maintenance PC

Check if the Maintenance PC is connected to the Basic SVP.
If not connected, connect it.

[Connected to]
The Basic SVP xxx.xxx.xxx.15

(2) <Initial screen>

(3) <Operation mode change>

Change the mode to [Modify Mode].
Select (CL) [Maintenance].

(4)
Select (CL) [Maintenance]-[SVP]-[Switch
SVP] from the menu.

INST03-12-620
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-630

(5) <Execution>
Execute switching.
Select (CL) [Yes].

NOTE: Switching takes about 20 minutes.

(6) <Configuration Information Transfer>

The message “Transferring storage system
configuration data...” is displayed.

(7) <SVP Switching Start>

The message “Wait for switching...” is displayed.
The Basic SVP and the Maintenance PC are
disconnected for the SVP switching process.
Wait for about three minutes until the switching is
completed.

INST03-12-630
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-640

(8) Verifying the LED

Make sure that statuses of LEDs on the SVP-BASIC and SVP-OPTION are those as shown in
the figure below in a lighting part.

SVP-OPTION
SVP-BASIC

Rear View of DKC-0

LED

Front View of SVP

SVP-BASIC SVP-OPTION

Light Light

Fig. 3.12.1.2-2 Confirmation of LEDs

INST03-12-640
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-650

3. Operating the Additional SVP

NOTE: This operation needs that Standby SVP is a [View mode].

(1) <Connection to the Additional SVP>

The Additional SVP restarts by the SVP switching indication from the Basic SVP.
Connect the Maintenance PC to the Additional SVP.

[Connected to]
The Additional SVP xxx.xxx.xxx.15

(2) <Initial Window>

Press the [Web Server Status] button.

(3) <Web Server Status Window>

Check if all function’s Status displays Ready.
After confirmation, close Web Server Status screen.

(4) <Operation mode change>

Change the mode to [Modify Mode].
Select (CL) [Maintenance].

INST03-12-650
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-660

(5) <Maintenance window>

Make sure that the ‘Maintenance’ window is open normally.
Close ‘Maintenance’ window.

(6) <Web Console>

If Customer doesn’t use Web Console/Storage Navigator via a customer PC, don’t need to do
the following confirmation work.
Please run Web Console/Storage Navigator from customer PC, and check whether you can
login using by Customer user-id and password.
NOTE: The user-id and password are defined by customer. Therefore, entrust a customer with
a login test.
If you can see the main screen of Web Console/Storage Navigator, the confirmation work is
done.

(7) <Select Maintenance>

Select (CL) [Maintenance].

(8)
Select (CL) [Maintenance]-[SVP]-[Switch
SVP] from the menu.

INST03-12-660
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-670

(9) <Execution>
Execute switching.
Select (CL) [Yes].

NOTE: Switching takes about 20 minutes.

(10) <Configuration Information Transfer>

The message “Transferring storage system
configuration data...” is displayed.

(11) <SVP Switching Start>

The message “Wait for switching...” is displayed.
The Additional SVP and the Maintenance PC are
disconnected for the SVP switching process.
Wait for about three minutes until the switching is
completed.

INST03-12-670
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-680

(12) Verifying the LED

Make sure that statuses of LEDs on the SVP-BASIC and SVP-OPTION are those shown in the
figure below in a lighting part.

SVP-OPTION
SVP-BASIC

Rear View of DKC-0

LED

Front View of SVP

SVP-BASIC SVP-OPTION

Light Light

Fig. 3.12.1.2-3 Confirmation of LEDs

INST03-12-680
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-12-690

4. Operating the Basic SVP

(1) Connecting the Maintenance PC
Connect the Maintenance PC to the Additional SVP.

[Connected to]
The Basic SVP xxx.xxx.xxx.15

(2) <Initial Window>

Press the [Web Server Status] button.

(3) <Web Server Status Window>

If all function’s Status displays Ready, switching is
completed.

End of verification of the setting.

5. Return to the working table and do the rest of the work.

New Installation: INST02-20
Non-Disruptive Installation: INST02-50

INST03-12-690
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-13-10

3.13 Installation of Filler Panel (DKC-F810I-FIHT)

Table 3.13-1 Parts List

No. Model Number Part Name Part No. Quantity Remarks
1 DKC-F810I-FIHT Filler Panel 5545408-A 1

INST03-13-10
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-13-20

3.13.1 Installation Procedure of Filler Panel

1. Installation of filler panel
a. Set the left side of the filler panel.
b. Set the right side of the filler panel while pushing it to the left.

RACK

Set the left side of

the filler panel.
Front View of
RACK
Filler Panel

Set the right side of the filler panel

while pushing it to the left.

Fig. 3.13.1-1 Installation of Filler Panel

INST03-13-20
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-13-30

2. Return to the working table and do the rest of the work.

New Installation: INST02-20,
Non-Disruptive Installation: INST02-50

INST03-13-30
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-14-10

3.14 Power ON/OFF Procedure

NOTICE: When some control frames (DKCs) are installed in the Disk-less configuration,
check the serial number of target DKC on the SVP screen and beware of a
attachment position to prevent mistakes. (See “5.2.4 Refer Configuration 3.
<DKC Configuration window>” (INST05-02-540).)

3.14.1 Power ON Procedure

1. Power ON Procedure of Storage system
a. Turn on the main circuit breakers at the PDUs on the Rack frames.
The equipment is in a standby mode when the PDU breaker is in a power-on state and the
power of equipment is off, therefore the FANs of the DKC and the DKU continue to
operate (*1). Execute this operation just before the power-on processing of the following
procedure b when the standby electricity must be controlled, because the standby
electricity (*2) exists in the equipment under this condition.
*1: All the FANs of DKC and DKU continue to operate.
*2: Refer to Table 3.14.1-1.

NOTICE: Turn on the breakers on all the PDUs that are connected to the DKC.
If any PDU is not turned on, the DKC may not become BS ON status.

Table 3.14.1-1 Maximum Standby Electricity per Chassis

No. Chassis Maximum Standby Electricity [VA]
1 CBXA/CBXB (Controller Chassis) 500
2 SBX (SFF Drive Chassis) 1,120
3 UBX (LFF Drive Chassis) 720
4 FBX (FMD Chassis) 1,280

INST03-14-10
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-14-20

b. Turn the “POWER ON/OFF” switch to “ON”, while turning the POWER ON/OFF
ENABLE switch to the ENABLE position.

DKCPANEL-0
DKCPANEL-0

BS-ON LED

PS-ON LED
Front View of DKC-0
POWER ON/OFF Switch

POWER ON/OFF ENABLE Switch

Fig. 3.14.1-1 Switch on DKCPANEL

INST03-14-20
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-14-30

2. Power ON Procedure of additional Rack frame

a. Turn on the circuit breakers at the PDUs on the additional Rack frame.

INST03-14-30
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-14-40

3. Power ON Procedure of Storage system in Power-On State of PDU Breaker

a. Turn the “POWER ON/OFF” switch to “ON”, while turning the POWER ON/OFF
ENABLE switch to the ENABLE position.

DKCPANEL-0
DKCPANEL-0

Front View of DKC-0

POWER ON/OFF Switch

POWER ON/OFF ENABLE Switch

Fig. 3.14.1-2 Switch on DKCPANEL

INST03-14-40
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-14-50

3.14.2 Power OFF Procedure

1. Power OFF Procedure of Storage system

NOTICE: Please confirm that maintenance operations (except for configuration

information setting) has been completed before powering OFF DKC.
When turning the breaker off before or during a power-off operation, an
emergency processing that transfers data to the SSD is performed with the
battery.
Make sure the power is completely turned off after executing the following
procedures because the emergency processing drains the batteries and
prolongs the next power-on time according to the remaining battery charge.

a. Turn the “POWER ON/OFF” switch to “OFF”, while turning the POWER ON/OFF
ENABLE switch to the ENABLE position. (Refer to Fig. 3.14.2-1.)

b. Procedure for checking the power OFF of Storage system

Perform all checks of the following (i) and (ii), and confirm the power OFF status of
storage system.
Even if the equipment is in the state of the power-off, the FANs of the DKC and the DKU
continue to operate (*1) because the equipment is in a standby mode. Execute the power-
off processing of the PDU breaker as the following procedure d when the standby
electricity must be controlled, because the standby electricity (*2) exists in the equipment
under this condition.
*1: All the FANs of DKC and DKU continue to operate.
*2: Refer to Table 3.14.1-1.

(i) Checking the PS-ON LED OFF

Move to the position where you can see the DKCPANEL from the front to be able to
check that the BS-ON LED on the DKCPANEL is on.
Check that the BS-ON LED is on and the PS-ON LED is off (*3). When the BS-ON
LED is off, turn on the power of storage system again and perform the power OFF
procedure from Step a.
*3: At this time, HDD ENABLE LED (green light) of SSD may light, however it is
acceptable.

INST03-14-50
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-14-60

DKCPANEL-0
DKCPANEL-0

BS-ON LED

PS-ON LED
Front View of DKC-0
POWER ON/OFF Switch

POWER ON/OFF ENABLE Switch

Fig. 3.14.2-1 Switch on DKCPANEL

(ii) Checking the SVP Power Off Event Log

Check that there are the logs of “System OFF” of the date or later which the power
OFF operation in Step a is operated to the Power Event Log for 1MP or more referring
to the log display in the SVP SECTION (SVP02-02-120).

c. Turn off the power of the SVP referring to the SVP SECTION (SVP01-170).

NOTICE: Make sure to perform the procedure d within 15 minutes after turning OFF the
power of SVP. If the condition that SVP is OFF and breaker is ON continues
for more than 15 minutes, the following occurs.
(If SVP High Availability kit is not installed) SVP power is forcibly turned ON.
(If SVP High Availability kit is installed) SVP failover takes place.

d. Turn off the main circuit breakers at the PDUs on the Rack frames.
NOTE: Be sure to turn off all the PDU breakers that are connected to the DKC.
If any PDUs are not turned off, DKC voltage alarm may be detected.

INST03-14-60
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-14-70

2. Power OFF Procedure of additional Rack frame

a. Turn off the main circuit breakers at the PDUs on the additional Rack frame.

INST03-14-70
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-14-80

3. Power OFF Procedure of Storage system in Power-On State of PDU Breaker

NOTICE: Please confirm that maintenance operations (except for configuration

information setting) have been completed before powering OFF DKC.

NOTICE: Notes on the Power OFF Operation of Device.

Confirm the below requirements when turning off the device.
• Make sure the SVP Mode is “View”.
• All users from Navigator should log off.

a. Turn the “POWER ON/OFF” switch to “OFF”, while turning the POWER ON/OFF
ENABLE switch to the ENABLE position.

DKCPANEL-0
DKCPANEL-0

BS-ON LED

PS-ON LED
Front View of DKC-0
POWER ON/OFF Switch

POWER ON/OFF ENABLE Switch

Fig. 3.14.2-2 Switch on DKCPANEL

INST03-14-80
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-14-90

b. Procedure for checking the power OFF of Storage system

Perform all checks of the following (i) and (ii), and confirm the power OFF status of
storage system.
Even if the equipment is in the state of the power-off, the FANs of the DKC and the DKU
continue to operate (*1) because the equipment is in a standby mode. The standby
electricity (*2) exists in the equipment under this condition.*1: All the FANs of DKC and
DKU continue to operate.
*1: All the FANs of DKC and DKU continue to operate.
*2: Refer to Table 3.14.1-1.

(i) Checking the PS-ON LED OFF

Move to the position where you can see the DKCPANEL from the front to be able to
check that the BS-ON LED on the DKCPANEL is on.
Check that the BS-ON LED is on and the PS-ON LED is off (*3). When the BS-ON
LED is off, turn on the power of storage system again and perform the power OFF
procedure from Step a.
*3: At this time, HDD ENABLE LED (green light) of SSD may light, however it is
acceptable.

(ii) Checking the SVP Power Off Event Log

Check that there are the logs of “System OFF” of the date or later which the power
OFF operation in Step a is operated to the Power Event Log for 1MP or more referring
to the log display in the SVP SECTION (SVP02-02-120).

INST03-14-90
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-14-100

3.14.3 Method of Disconnecting Power Supply to Storage system

1. When there are some circuit breakers in PDU.
a. Turn off the circuit breakers of PDU.

2. When there are no circuit breakers in PDU.

a. Disconnect the power cables corresponding the each unit from PDU.

PDU PDU

Rear View of
Rack Frame

PDU (When there are some circuit breakers) PDU (When there is no circuit breakers)

Circuit Breaker

OFF

Power Cable

Fig. 3.14.3-1 Work Example of Disconnecting Power Supply

INST03-14-100
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-15-10

3.15 Mounting on Rack Frame

You can use a special lifter to mount the storage system on the rack frame.
This section explains a procedure for the mounting using the special lifter.
If you do not use the lifter, you must follow another procedure.

CAUTION
Rack mounting and lifter operation should only be conducted by a person who has been
trained and qualified since the storage system could turn over or a worker could be
caught under the storage system.

(1) External appearance of the special lifter

Fig. 3.15-1 shows external appearance of the special lifter.

Handle
1,900 mm

590 mm
Valve
1,611 mm

Band
Base
Stopper

880 mm 970 mm

Fig. 3.15-1 External lifter

INST03-15-10
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-15-20

3.15.1 Mounting Lifter on Rack Frame

CAUTION
• Rack mounting and lifter operation should only be conducted by a person who has
been trained and qualified since the storage system could turn over or a worker could
be caught under the storage system.
• Be sure to perform the operation with two or more workers.
• Work carefully because the mass of the single DKC is about 140 kg, LFF SBB is about
27 kg, SFF SBB is about 23 kg and FMU is about 20 kg.

(1) Bring the special lifter close to the storage system to be mounted and apply the brake to the
lifter.
(2) Put the storage system on the special lifter.
(3) Secure the storage system to the lifter with a band of the lifter.
Bind the storage system with the band tightly by fitting the length of the belt to the storage
system.

Handle

Valve Front side of the storage system

to be mounted
Band
Stopper Storage system to be
Base mounted

Fig. 3.15.1-1 Putting the Storage systems on Special Lifter

INST03-15-20
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-15-30

3.15.2 Mounting Storage system on Rack Frame

CAUTION
If the storage system falls when the elevator of the lifter is at a high position, a personal
injury will be caused.
Perform the positioning, fastening, or other handlings very carefully.

CAUTION
• Rack mounting and lifter operation should only be conducted by a person who has
been trained and qualified since the storage system could turn over or a worker could
be caught under the storage system.
• Operate the valve slowly when opening it. If it is opened quickly, the elevator of the lifter
descends rapidly and may cause personal injury.
• Be sure to perform the operation with two or more workers.
• Work carefully because the mass of the single DKC is about 140 kg, LFF SBB is about
27 kg, SFF SBB is about 23 kg and FMU is about 20 kg.
• Please be cautious of your safety and use a stepladder as you need while assembling
or removing parts on top of the RACK frame.

(1) Take off the brake of the special lifter on which the storage system has been put, and move the
lifter close to the rack frame.
(2) Adjust the position of the storage system so that it is seated in the center of the rack frame.
(3) Move the pumping handle of the special lifter to the right and left repeatedly to lift the storage
system up to the height suitable for the mounting.
Be careful not to lift the elevating base too high. If you lift it too high, lower it by opening the
up/down valve gently.
(4) Remove the band and adjust the position of the storage system so that the storage system
comes in the center in front of the rack frame. If the storage system is positioned off-centered,
a screw contacts the front bezel preventing the bezel from being opened or closed.
(5) Shift the storage system onto the rails in the rack frame. When shifting the storage system,
push it in to the end gently.

INST03-15-30
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-15-40

(6) After mounting the storage system on the rack frame, lower the elevating base to the
lowermost position by gently opening the up/down valve of the special lifter and take off the
brake of the lifter.
(7) Move the special lifter to the place where the lifter does not disturb the following works.

Part

Lifter
Front
Frame
Push in
Pumping Handle

Storage system Valve

Already installed

Base
Up/down
Elevator

Fig. 3.15.2-1 Mounting Storage system on Rack Frame

INST03-15-40
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-16-10

3.16 LAN Cable Wiring for SVP

The SVP consists of the four LAN ports in all. The applications of the LAN cables that are
connected to these LAN ports are shown in the table below.
Refer to the table below for the LAN cable wiring operation procedures.
Please note that the EMI cores should be installed in each LAN cable to connect them to the three
LAN ports (PUBLIC, INTERNAL, CONSOLE).

SVP-OPTION
SVP-BASIC

Rear View of
DKC-0 CONSOLE

PUBLIC J84 INTERNAL

Front View of SVP

Fig. 3.16-1 LAN Port Positions of SVP

Table 3.16-1 Application of LAN Cables for SVP

No. Port Name Work Pages EMI Core NOTE
1 PUBLIC When SNMP Web INST03-16-20, 30 Required Connected to both SVP-BASIC and
Console is used SVP-OPTION.
2 INTERNAL When connected to INST03-16-20 Required Only connected to SVP-BASIC.
other devices Unnecessary to SVP-OPTION.
3 J84 When DKC-F810I- INST03-07-640 Unnecessary In the twin DKC configuration,
MOD5/MOD30/ connect to the HUBBOX-10 (J83) in
MOD1J is used the DKC-1. (The SVP-OPTION is
unused.)
4 CONSOLE When CE Laptop INST03-01-130 Required Generally, only connected to SVP-
PC is used BASIC. Connected to SVP-OPTION
only when a trouble occurs on SVP-
BASIC.

INST03-16-10
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-16-20

3.16.1 Procedures of LAN Cable Wiring for SVP

1. Connecting the LAN Cable with the SVP-BASIC

NOTICE: To connect the LAN cable with the INTERNAL port of the SVP, connect it only
with the SVP-BASIC.
Connecting the cable with the INTERNAL port of the SVP-OPTION is not
necessary.

a. Wire the LAN cable after pulling the cable into the RACK.
b. Pass the LAN cable through the EMI core, and wind the cable in the EMI core once.
c. Connect the LAN cable with the SVP-BASIC port (PUBLIC or INTERNAL).

SVP-BASIC

INTERNAL 25 – 30mm
50 – 60mm
PUBLIC (*2)
(*2)

EMI Core
EMI Core (*1)

LAN Cable
(Wind the cable in EMI Core once.)

*1: EMI Core for PUBLIC Port is the

components of DKC-F810I-SVP or
DKC810I-CBXA.
EMI Core for INTERNAL Port is the
components of DKC810I-CBXA.
*2: Recommended dimension.

LAN Cable Rear View of

RACK-00

Fig. 3.16.1-1 Connection of LAN Cable (SVP-BASIC)

INST03-16-20
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-16-30

2. Wiring LAN Cable with SVP-OPTION

NOTICE: To connect the LAN cable with the INTERNAL port of the SVP, connect it only
with the SVP-BASIC.
Connecting the cable with the INTERNAL port of the SVP-OPTION is not
necessary.

a. Wire the LAN cable after pulling the cable into the RACK.
b. Pass the LAN cable through the EMI core, and wind the cable in the EMI core once.
c. Connect the LAN cable with the PUBLIC port of the SVP-OPTION.

SVP-OPTION

25 – 30mm
50 – 60mm (*2)
PUBLIC (*2)

EMI Core (*1) EMI Core

LAN Cable
(Wind the cable in EMI Core once.)

*1: EMI Core for PUBLIC Port is the

components of DKC-F810I-SVP.
*2: Recommended dimension

Rear View of
LAN Cable RACK-00

Fig. 3.16.1-2 Connection of LAN Cable (SVP-OPTION)

INST03-16-30
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-17-10

3.17 Installation of SM Size without adding Cache Memory

NOTICE: The CM capacity decreases if SM size is increased by this operation. Make

sure there will be no performance effect and so on in the configuration to be
built. For the information on cache memory capacity, please refer to INST06-
10.

Rough time of SM size installation becomes addition of the following A, B and C.

Table 3.17-1 Rough time of installation

Process Time Remarks
A BASIC CM PCB blocking time 5 ~ 60min × 2 (*1)
B BASIC CM PCB diagnosis time 10min × 2
C BASIC CM PCB recovering time 5 ~ 20min × 2 (*1)

*1: Standard processing time is indicated. The processing time depends on the use situation,
especially, the influence of the amount of write pending is received. When the amount of
write pending is large, time more than the indication value might be required.

INST03-17-10
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-17-20

1. Setting up the New Device Structure Information

(1) <Mode Change>
Change the mode to Modify Mode.
Select (CL) [Install].

(2) <Start the ‘Menu Dialog’ screen>

Select (CL) [Change Configuration].

(3) <Start Device Structure Setup screen>

Select (CL) [Installation] in the ‘Menu
Dialog’ dialog box and select (CL) [OK].

(4) <Select a part to be changed>

Select (CL) [SM Capacity], and select
(CL) [OK].

INST03-17-20
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-17-30

(5) <DKC Configuration screen>

In the ‘DKC Configuration’ screen, select
(CL) [Cache].
Go to Step (6).

NOTE: It is impossible to install

multiple types of parts at the
same time.

Make sure that the all input items are

correct and select (CL) [>>Next].
Go to Step (7).

(6) <Cache Configuration screen>

Select (CL) [SM function] in the ‘Cache
Configuration’ screen.
Go to Step (6)-1.

Make sure that the all input items are

correct and select (CL) [OK].
Go back to Step (5).

(6)-1 <SM function Define screen>

Set the SM function in the ‘SM function
Define’ screen, select (CL) [OK].
Go back to Step (6).

INST03-17-30
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-17-40

(7) <Start installation>

Select (CL) [Yes] in response to “Are you
sure you want to renew storage system?”.

When [No] is selected (CL), returns to

INST03-17-20 Step (2).

(8) <End of system update processing>

“Renewal process has completed. Please
check storage system status.” is displayed
when recovery processing on all installed
components is completed. Select (CL)
[OK] in response to this message.

INST03-17-40
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-17-50

(9)
Execute an operation for backing up the
configuration information.
Prepare the removable media for backup
and insert the media.
Please select (CL) the [Refresh] button,
and update drive information.
Select (CL) the drive and the PC in which
the media was inserted. Select (CL) the
[OK] button.
NOTE: For the procedure of
backing up the configuration
information to a CD-R,
see page MICRO07-190.

(10)
When this procedure is completed, the message
“Please remove the Config media.” is displayed.
Remove the configuration information media,
select (CL) [OK].

(11)
After the procedure is completed, return
to ‘Install’.
Select (CL) [File]-[Exit].

(12) <Mode Change>

Change the mode to View Mode.

INST03-17-50
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-18-10

3.18 Installation of Decoration Panel, Key Kit, Front Door, Front Door Hinge Kit and PC
Tray for RK42 (DKC-F810I-DECO/DECOP/KYH/KYP/FDR/FDH42/TR42)

Table 3.18-1 Parts List

No. Model Number Part Name Part No. Quantity Remarks
1 DKC-F810I-DECO Top Panel 3287238-1 1
Lower Panel 3287249-1 1
Fixing Bracket 3287239-1 4
Panel 2854946-1 2
Screw SB406N 12
Screw SB410N 2
2 DKC-F810I-DECOP Top Panel (HP) 3290502-A 1
Lower Panel 3287249-1 1
Fixing Bracket 3287239-1 4
Panel 2854946-1 2
Screw SB406N 12
Screw SB410N 2
3 DKC-F810I-KYH Handle ASSY 3283382-A 1
Key — 1
Screw SB306N 4
4 DKC-F810I-KYP Bracket (KEY) 3283278-1 1
Stopper Bracket 5545386-1 1
Screw SB306N 4
Screw SB406N 2
5 DKC-F810I-FDR Front Door 2855887-A 1
6 DKC-F810I-FDH42 Hinge U 5552841-1 1
Hinge L 5552842-1 1
Stopper 5555001-1 1
Screw SB410N 1
Screw SB510N 2
Socket Bolt BS510N 4
Collar 5513552-404 1
LL Washer 5513553-433 1
7 DKC-F810I-TR42 PC Tray 3287327-A 1
Stopper 5552806-1 1
Door Bar 5552807-1 1
Shipping Stopper 5552808-1 1
Hinge 5552993-1 1 Hinge L
Hinge 5552814-1 1 Hinge R
Screw SB408N 4
Screw SB410N 4
Screw (Stopper) 5513661-412 1

INST03-18-10
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-18-20

3.18.1 Installation Procedure of Decoration Panel (DKC-F810I-DECO/DECOP)

1. Installation of front parts
a. Install the top panel on the front upper part of the RACK, and secure it with the two
screws.
b. Install the lower panel on the front lower part of the RACK, and secure it with the two
screws.
c. Install the four fixing brackets on the front side of the RACK, and secure them with the
eight screws.

Fixing Bracket

Screw (SB406N)

Fixing Bracket

Top Panel
Screw (SB406N) Screw
(SB406N)
Fixing Bracket

Screw (SB406N)

Screw
(SB406N)
Fixing Bracket

Front View of
RACK

Lower Panel
Screw (SB406N)

Fig. 3.18.1-1 Installation of Panels (Front)

INST03-18-20
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-18-30

d. Install the two panels on the fixing brackets, and secure it with the two screws.

Fixing Bracket

Fixing Bracket
Panel

Panel

Fixing
Bracket

Fixing Bracket

Front View of
RACK
Screw (SB410N)

Fig. 3.18.1-2 Installation of Panels (Front)

2. Return to the working table and do the rest of the work.

New Installation: INST02-10
Non-Disruptive Installation: INST02-40

INST03-18-30
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-18-40

3.18.2 Installation Procedure of Key Kit (DKC-F810I-KYH)

1. Installation of rear parts
a. Install the Handle ASSY on the rear side of the rear door, and secure it with the four
screws.
b. When the rear door is unlocked, hung the key on the locking clamp of the rear side of the
rear door.

Rear Door

Locking Clamp

Key

Rear View of
RACK
Handle ASSY

Screw (SB306N)
4

Fig. 3.18.2-1 Installation of Handle ASSY (Rear)

INST03-18-40
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-18-50

2. Return to the working table and do the rest of the work.

New Installation: INST02-10
Non-Disruptive Installation: INST02-40

INST03-18-50
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-18-60

3.18.3 Installation Procedure of Key Kit (DKC-F810I-KYP)

1. Installation of rear parts
a. Install the stopper bracket, and secure it with the two screws  slightly. Then fully tighten
the two screws  by pressing the stopper bracket downword.
b. Install the bracket (KEY), and secure it with the four screws .

Screw 
(SB406N)  2

Stopper
Bracket

Rear View of
RACK

Screw  (SB306N)
4

Bracket (KEY)

Fig. 3.18.3-1 Installation of Parts (Rear)

INST03-18-60
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-18-70

2. Return to the working table and do the rest of the work.

New Installation: INST02-10
Non-Disruptive Installation: INST02-40

INST03-18-70
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-18-80

3.18.4 Installation Procedure of Front Door Hinge Kit (DKC-F810I-FDH42)

1. Installation of front parts
a. Install the hinge U, and secure it with the two socket bolts.
b. Install the stopper, and secure it with the two screws.
c. Install the hinge L, and secure it with the two socket bolts.
d. Install the collar, LL washer and screw on the hinge L.

Hinge U

Socket Bolt
(BS510N)

Stopper

Screw (SB510N)

Screw (SB410N)
LL Washer
Collar
Front View of
RACK
Hinge L
Socket Bolt
(BS510N)

Fig. 3.18.4-1 Installation of Parts (Front)

INST03-18-80
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-18-90

2. Return to the working table and do the rest of the work.

New Installation: INST02-10
Non-Disruptive Installation: INST02-40

INST03-18-90
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-18-100

3.18.5 Installation Procedure of Rack Front Door (DKC-F810I-FDR)

1. Installation of Front Door
a. Loosen the two socket bolts on the front top of the rack and turn the hinge U.
b. Insert the pin of the hinge L into the hole on the bottom of the front door to mount the front
door.
c. Turn the hinge U back and insert the pin of the hinge U into the hole on the front door.
d. Tighten the two socket bolts to secure the hinge U.

Pin
Hole
Hinge U

Socket Bolt

Hinge L

Pin

Front Door Front View of

RACK

Fig. 3.18.5-1 Installation of Front Door

INST03-18-100
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-18-110

e. Attach the wire rope to the screw on the hinge L on the front bottom of the rack.
f. Secure the FG cable to the rack with the screw and washer.

FG Cable
Washer
Screw
(WT004N)
(SB408N)

Front View of
RACK
Wire Rope Hinge L Screw

Fig. 3.18.5-2 Installation of Wire Rope and FG Cable

2. Return to the working table and do the rest of the work.

New Installation: INST02-10
Non-Disruptive Installation: INST02-40

INST03-18-110
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-18-120

3.18.6 Installation Procedure of PC Tray for RK42

1. Install the PC Tray
a. Insert the edge of the Hinge R into the insertion hole on the PC Tray and tighten the two
screws to secure the Hinge R to the back side of the rear door.

Rear Door

PC Tray
Rear View of
Rear Door

Hinge R
Insertion Hole

Edge
Screw (SB410N)

Fig. 3.18.6-1 Attachment of PC Tray and Hinge

INST03-18-120
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-18-130

b. Insert the edge of the Hinge L into the insertion hole on the PC Tray and tighten the two
screws to secure the Hinge L to the back side of the rear door.

PC Tray

Insertion Hole

Edge

Hinge L

Screw (SB410N)

Rear View of
Rear Door

Fig. 3.18.6-2 Attachment of Hinge

INST03-18-130
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-18-140

c. Insert the edge of the Door Bar into the PC Tray and turn the Door Bar 90 degrees in a
counterclockwise direction.

PC Tray

Door Bar

Rear View of
Rear Door

90 Degree Turn

Fig. 3.18.6-3 Attachment of Door Bar

INST03-18-140
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-18-150

d. Attach the Stopper to the opposite edge of the Door Bar.

e. Secure the Stopper attached to the Door Bar to the back side of the rear door with the two
screws.

Rear View of
Rear Door

Door Bar
Stopper

Screw (SB408N)

Fig. 3.18.6-4 Attachment of Stopper

INST03-18-150
Hitachi Proprietary DKC810I
Rev.0 / Dec.2013 Copyright © 2013, Hitachi, Ltd.
INST03-18-160

f. Attach and secure the Shipping Stopper with the screw.

Shipping Stopper [During arrangement of rack]

Secure the
Shipping Stopper
in the upper
position.
Screw (Stopper)

[During shipment of rack]

Secure the
Shipping Stopper
in the lower
position.

Rear View of
Rear Door

Fig. 3.18.6-5 Attachment of Shipping Stopper

2. Return to the working table and do the rest of the work.

New Installation: INST02-10
Non-Disruptive Installation: INST02-40

INST03-18-160