ENGLISH ENGLISH ENGLISH ENGLISH

Installation and User Manual

version 1.04

TLM8

2014/30/UE

EN55022:2010 EN61000-6-2:2005 EN61000-6-4:2007

SYSTEM IDENTIFICATION
 KEY TO SYMBOLS

Below are the symbols used in the manual to draw the reader's attention:

Warning! Risk of electrocution.

Warning! This operation must be performed by skilled workers.

Read the following indications carefully.

Further information.

GUARANTEE
24 months from the delivery document date. The guarantee covers only defected parts and includes the replacement parts and
labour. All shipping and packing costs are paid by the customer. It is possible to have the repair in guarantee on condition that the
returned product has not been transformed, damaged or repaired without authorization. No guarantee is applicable on returned
products without the original label and/or serial number. No guarantee against misuse.
Batteries: Laumas provides 1 year guarantee from the date of delivery note, against material defects or battery manufacturing faults.

Disposal of Waste Equipment by Users in Private Households in the European Union

This symbol on the product or on its packaging indicates that this product must not be disposed of with
your other household waste. It is your responsibility to dispose of your waste equipment by handing it
over to a designated collection point for the recycling of waste electrical and electronic equipment. The
separate collection and recycling of your waste equipment at the time of disposal will help preserve
natural resources and protect human health and the environment. For more information about where you
can drop off your waste equipment for recycling, please contact your local waste disposal Authority or
the equipment retailer.
 TABLE OF CONTENTS

USER WARNINGS ................................................................................................................. 1

RECOMMENDATIONS FOR CORRECT INSTALLATION OF WEIGHING INSTRUMENTS . 1
RECOMMENDATIONS FOR CORRECT INSTALLATION OF THE LOAD CELLS ............... 1
LOAD CELL INPUT TEST (QUICK ACCESS) ......................................................................... 3
LOAD CELL TESTING ............................................................................................................. 3
MAIN SPECIFICATIONS OF THE INSTRUMENT.................................................................. 4
TECHNICAL SPECIFICATIONS ............................................................................................ 5
ELECTRICAL CONNECTIONS .............................................................................................. 6
BASIC INFORMATION............................................................................................................. 6
WIRING DIAGRAM................................................................................................................... 6
KEYS AND SYMBOLS FUNCTIONS ..................................................................................... 8
MENU MAP ............................................................................................................................ 9
SETPOINT ................................................................................................................................ 9
SYSTEM PARAMETERS ......................................................................................................... 9
INSTRUMENT COMMISSIONING ........................................................................................ 11
PROGRAMMING OF SYSTEM PARAMETERS .................................................................. 12
THEORETICAL CALIBRATION ............................................................................................. 12
MAXIMUM CAPACITY ....................................................................................................................13
TARE WEIGHT ZERO SETTING .....................................................................................................13
ZERO VALUE MANUAL ENTRY .....................................................................................................13
REAL CALIBRATION (WITH SAMPLE WEIGHTS) ............................................................... 14
CONFIRMATION AND CHANGE OF ACTIVE CHANNELS................................................... 15
EQUALIZATION ..................................................................................................................... 16
FILTER ON THE WEIGHT ...................................................................................................... 17
ANTI PEAK ......................................................................................................................................17
ZERO PARAMETERS ............................................................................................................ 18
RESETTABLE WEIGHT SETTING FOR SMALL WEIGHT CHANGES ..........................................18
AUTOMATIC ZERO SETTING AT POWER-ON ..............................................................................18
ZERO TRACKING ...........................................................................................................................18
SETTING UNITS OF MEASURE ............................................................................................ 19
DISPLAY COEFFICIENT .................................................................................................................19
OUTPUTS AND INPUTS CONFIGURATION ......................................................................... 21
SEMI-AUTOMATIC TARE (NET/GROSS).............................................................................. 22
PRESET TARE (SUBTRACTIVE TARE DEVICE) ................................................................. 23
SEMI-AUTOMATIC ZERO (WEIGHT ZERO-SETTING FOR SMALL VARIATIONS) ............ 23
PEAK ...................................................................................................................................... 24
ANALOG OUTPUT ................................................................................................................. 24
SERIAL COMMUNICATION SETTING .................................................................................. 25
RS485 SERIAL COMMUNICATION ................................................................................................27
DIRECT CONNECTION BETWEEN RS485 AND RS232 WITHOUT CONVERTER .......................27
AUTOMATIC DIAGNOSTICS OF LOAD DISTRIBUTION ...................................................... 28
 TEST....................................................................................................................................... 29
EVENTS LOG ......................................................................................................................... 30
INFO MENU ............................................................................................................................ 30
SETPOINT PROGRAMMING ............................................................................................... 31
USE WITH W SERIES INSTRUMENTS ............................................................................... 32
CONNECTION TO THE WEIGHT INDICATOR ...................................................................... 32
ADDITIONAL MENU MAP...................................................................................................... 33
TLM8 REMOTE CONTROL .................................................................................................... 34
REMOTE KEYPAD LOCKING.........................................................................................................34
ADDITIONAL ALARMS .......................................................................................................... 34
ALARMS .............................................................................................................................. 35
PRINTING EXAMPLES ........................................................................................................ 37
RESERVED FOR THE INSTALLER..................................................................................... 39
MENU LOCKING .................................................................................................................... 39
MENU UNLOCKING ............................................................................................................... 39
TEMPORARY MENU UNLOCKING ....................................................................................... 39
DATA DELETION AND PROGRAM SELECTION ................................................................. 39
KEYPAD OR DISPLAY LOCKING ......................................................................................... 40
DECLARATION OF CONFORMITY - EU ............................................................................. 41
 USER WARNINGS

RECOMMENDATIONS FOR THE PROPER USE OF WEIGHING INSTRUMENT

- Keep away from heat sources and direct sunlight
- Repair the instrument from rain (except special IP versions)
- Do not wash with water jets (except special IP versions)
- Do not dip in water
- Do not spill liquid on the instrument
- Do not use solvents to clean the instrument
- Do not install in areas subject to explosion hazard (except special Atex versions)

RECOMMENDATIONS FOR CORRECT INSTALLATION OF WEIGHING INSTRUMENTS

The terminals indicated on the instrument’s wiring diagram to be connected to earth must
have the same potential as the weighed structure (same earthing pit or earthing system). If
you are unable to ensure this condition, connect with an earthing wire the terminals of the
instrument (including the terminal – SUPPLY) to the weighed structure.
The cell cable must be individually led to its panel input and not share a conduit with other cables;
connect it directly to the instrument terminal strip without breaking its route with support terminal strips.
Use “RC” filters on the instrument-driven solenoid valve and remote control switch coils.
Avoid inverters in the instrument panel; if inevitable, use special filters for the inverters and separate
them with sheet metal partitions.
The panel installer must provide electric protections for the instruments (fuses, door lock switch
etc.).
It is advisable to leave the equipment always switched on to prevent the formation of condensation.

MAXIMUM CABLE LENGTHS

- RS485: 1000 metres with AWG24, shielded and twisted cables
- Analog current output: up to 500 metres with 0.5 mm2 cable
- Analog voltage output: up to 300 metres with 0.5 mm2 cable

RECOMMENDATIONS FOR CORRECT INSTALLATION OF THE LOAD CELLS

INSTALLING LOAD CELLS: The load cells must be placed on rigid, stable in-line structures; it
is important to use the mounting modules for load cells to compensate for misalignment of the
support surfaces.

PROTECTION OF THE CELL CABLE: Use water-proof sheaths and joints in order to protect the
cables of the cells.

-1-
MECHANICAL RESTRAINTS (pipes, etc.): When pipes are present, we recommend the use of
hoses and flexible couplings with open mouthpieces with rubber protection; in case of hard pipes,
place the pipe support or anchor bracket as far as possible from the weighed structure (at a distance
at least 40 times the diameter of the pipe).
WELDING: Avoid welding with the load cells already installed. If this cannot be avoided, place the
welder ground clamp close to the required welding point to prevent sending current through the load
cell body.

WINDY CONDITIONS - KNOCKS - VIBRATIONS: The use of weigh modules is strongly

recommended for all load cells to compensate for misalignment of the support surfaces. The system
designer must ensure that the plant is protected against lateral shifting and tipping relating to:
shocks and vibration; windy conditions; seismic conditions in the installation setting; stability of the
support structure.

EARTHING THE WEIGHED STRUCTURE: By means of a copper wire with suitable cross-section,
connect the cell upper support plate with the lower support plate, then connect all the lower plates to
a single earthing system. Electrostatic charges accumulated because of the product rubbing against
the pipes and the weighed container walls are discharged to the ground without going through or
damaging the load cells. Failure to implement a proper earthing system might not affect the
operation of the weighing system; this, however, does not rule out the possibility that the cells and
connected instrument may become damaged in the future. It is forbidden to ensure earthing system
continuity by using metal parts contained in the weighed structure.

FAILURE TO FOLLOW THE INSTALLATION RECOMMENDATIONS WILL BE CONSIDERED

A MISUSE OF THE EQUIPMENT

OK OK NO

NO NO OK

-2-
 LOAD CELL INPUT TEST (QUICK ACCESS)
3s
 
From the weight display, press for 3 seconds: the top of the
display shows the gross weight; the bottom shows the response
signal of each load cell expressed in mV with three decimals.
Example: a load cell with 2.000 mV/V sensitivity provides a
response signal between 0 and 10 mV.

LOAD CELL TESTING

Load cell resistance measurement (use a digital multimeter):

- Turn off the instrument.

- The value between the positive signal wire and the negative signal wire must be equal or similar
to the one indicated in the load cell data sheet (output resistance).
- The value between the positive excitation wire and the negative excitation wire must be equal or
similar to the one indicated in the load cell data sheet (input resistance).

Load cell voltage measurement (use a digital multimeter):

- Turn on the instrument.

- Take out the load cell to be tested from underneath the container, or alternatively, lift the
container support.
- Make sure that the excitation of two wires of the load cell connected to the instrument (or
amplifier) is 5 VDC ±3%.
- Measure the response signal between the positive and the negative signal wires by directly
connecting them to the tester, and make sure that it is comprised between 0 and 0.5 mV.
- Apply load to the cell and make sure that there is a signal increment.

IF ONE OF THE ABOVE CONDITIONS IS NOT MET, PLEASE CONTACT THE TECHNICAL
ASSISTANCE SERVICE.

-3-
 MAIN SPECIFICATIONS OF THE INSTRUMENT

Weight transmitter with 6-wire load cells inputs suitable for assembly on back panel fitted
Omega/DIN rail. Dimensions: 148x92x60 mm. Backlit LCD graphic display, 128x64 pixel resolution,
60x32 mm viewing area. 5-key keypad.
16 bit analog output (tension or current).
RS485 serial port for connection to: PC/PLC up to 32 instruments (max 99 with line repeaters) by
ASCII Laumas or ModBus R.T.U. protocol, remote display, printer. Optional: integrated Profibus DP,
DeviceNet, CANopen, Profinet IO, Ethernet/IP, Ethernet TCP/IP, Modbus TCP, RS232/RS485,
SERCOS III, PowerLink, CC-Link output.

8 independent channels:automatic detection of connected load cells.

Digital equalization: load cell response uniformed via software.
Load distribution: graph showing the weight percentage on each load cell.
Automatic diagnostics: load distribution check to detect any faults.
Events log: storage of the last 50 events: calibrations, zero-settings, errors, equalizations.
Alarm Relay: outputs can be set to switch in case of alarm.

-4-
 TECHNICAL SPECIFICATIONS

POWER SUPPLY and CONSUMPTION (VDC) 12/24 VDC ±10%; 5 W

NO. OF LOAD CELLS IN PARALLEL and SUPPLY max 16 (350 ohm); 5 VDC / 240 mA
LINEARITY < 0.01% F.S.
ANALOG OUTPUT LINEARITY < 0.01% F.S.
THERMAL DRIFT < 0.0005% F.S./°C
ANALOG OUTPUT THERMAL DRIFT < 0.003 % F.S./°C
A/D CONVERTER 8 channels, 24 bit (16000000 points), 4.8 kHz
DIVISIONS
±999999
(with measurement range ±10 mV = sens. 2 mV/V)
MEASUREMENT RANGE ±39 mV
MAX SENSITIVITY OF USABLE LOAD CELLS ±7 mV/V
MAX CONVERSIONS PER SECOND 600 conversions/second
DISPLAY RANGE ±999999
NO. OF DECIMALS / DISPLAY INCREMENTS 0÷4 / x 1 x 2 x 5 x 10 x 20 x 50 x 100
DIGITAL FILTER / READINGS PER SECOND 11 levels / 5÷600 Hz
RELAY OUTPUTS N. 5 - max 115 VAC; 150 mA
DIGITAL INPUTS N. 3 - optoisolated 5 - 24 VDC PNP
SERIAL PORTS RS485
BAUD RATE 2400, 4800, 9600, 19200, 38400, 115200
HUMIDITY (non condensing) 85%
STORAGE TEMPERATURE -30°C +80°C
WORKING TEMPERATURE -20°C +60°C
ANALOG OUTPUT 0÷20 mA; 4÷20 mA (max 400 ohm);
16 bit - 65535 divisions 0÷10 V; 0÷5 V (min 2 kohm)

RELAY OUTPUTS N. 5 - max 30 VAC, 60 VDC; 150 mA

WORKING TEMPERATURE -20°C +50°C
Equipment to be powered by 12-24 VDC LPS or Class 2 power source.

-5-
 ELECTRICAL CONNECTIONS

BASIC INFORMATION

- It is recommended that the power supply negative pole be grounded.

- It is possible to supply up to 16 350 ohm load cells.
- Connect terminal “–SUPPLY” to the RS485 common of the connected instruments in the event
that these receive alternating current input or that they have an optically isolated RS485.
- In case of an RS485 network with several devices it is recommended to activate the 120 ohm
termination resistance on the two devices located at the ends of the network, as described in the
paragraph RS485 SERIAL CONNECTION.

WIRING DIAGRAM

LOAD CELL 1 LOAD CELL 2 LOAD CELL 3 LOAD CELL 4

SH

SH

SH

SH
-SIG
+SIG

-SIG
+SIG

-SIG
+SIG

-SIG
+SIG
-REF
+REF

-REF
+REF

-REF
+REF

-REF
+REF
+EX

+EX

+EX

+EX
-EX

-EX

-EX

-EX

1 2 3 4 5 6 7 8 9 10 11 12 13

14 15 16 17 18 19 20 21 22 23 24 25 26
+REF

+REF

+REF

+REF
-REF

-REF

-REF

-REF
+SIG

+SIG

+SIG

+SIG
-SIG

-SIG

-SIG

-SIG
+EX

+EX

+EX

+EX
-EX

-EX

-EX

-EX
SH

SH

SH

SH

LOAD CELL 5 LOAD CELL 6 LOAD CELL 7 LOAD CELL 8

In case of difficulty connecting all the reference wires of the installed load cells, simply connect
those of the load cell located at the average distance from the instrument. The reference wires not
used must be individually isolated.

USE OF 4-WIRE LOAD CELLS: if all the load cells used are 4-wire, make a jumper between EX-
(10) and REF- (7) and between EX+ (17) and REF+ (20).

-6-
 27
OUT 1 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

IN 1
OUT COMMON

IN COMMON
OUT 2

+
IN 2
OUT 4
OUT 3

IN 3
OUT 5

+ 0÷10 VDC

+SUPPLY

-SUPPLY
+ 0÷20 - 4÷20 mA

-COMMON
+

-
OUTPUTS INPUTS ANALOG RS485 12/24 VDC
max 115 VAC 150 mA supply 5÷24 VDC OUTPUT SUPPLY

TERMINALS LEGEND

1 -LOAD CELL 1 SIGNAL 22 +LOAD CELL 7 SIGNAL

-LOAD CELLS 7 and 8 EXCITATION (-EX)
2 +LOAD CELL 1 SIGNAL 23
LOAD CELLS SHIELD
-LOAD CELLS 1 and 2 EXCITATION (-EX)
3 24 +LOAD CELLS 7 and 8 EXCITATION (+EX)
LOAD CELLS SHIELD
4 +LOAD CELLS 1 and 2 EXCITATION (+EX) 25 -LOAD CELL 8 SIGNAL
5 -LOAD CELL 2 SIGNAL 26 +LOAD CELL 8 SIGNAL
6 +LOAD CELL 2 SIGNAL 27 OUTPUT No. 1
7 -LOAD CELLS REF/SENSE 28 OUTPUT No. 2
8 -LOAD CELL 3 SIGNAL 29 OUTPUT No. 3
9 +LOAD CELL 3 SIGNAL 30 OUTPUT No. 4
-LOAD CELLS 3 and 4 EXCITATION (-EX)
10 31 OUTPUT No. 5
LOAD CELLS SHIELD
11 +LOAD CELLS 3 and 4 EXCITATION (+EX) 32 OUTPUT COMMON
12 -LOAD CELL 4 SIGNAL 33 INPUT No. 1 (+VDC min 5 V max 24 V)
13 +LOAD CELL 4 SIGNAL 34 INPUT No. 2 (+VDC min 5 V max 24 V)
14 -LOAD CELL 5 SIGNAL 35 INPUT No. 3 (+VDC min 5 V max 24 V)
15 +LOAD CELL 5 SIGNAL 36 INPUT COMMON (-VDC 0 V)
-LOAD CELLS 5 and 6 EXCITATION (-EX)
16 37 +ANALOG OUTPUT 0÷20 or 4÷20 mA
LOAD CELLS SHIELD
17 +LOAD CELLS 5 and 6 EXCITATION (+EX) 38 +ANALOG OUTPUT 0÷10 V
18 -LOAD CELL 6 SIGNAL 39 RS485: +
19 +LOAD CELL 6 SIGNAL 40 RS485: -
20 +LOAD CELLS REF/SENSE 41 +SUPPLY (12/24 VDC)
-SUPPLY (12/24 VDC)
21 -LOAD CELL 7 SIGNAL 42 RS485: SHIELD, GND, -ANALOG OUTPUT
COMMON

-7-
 KEYS AND SYMBOLS FUNCTIONS

Long press
KEY Short press Into menus
(3 s)
Cancel or return to previous
Semi-automatic zero Tare resetting
menu
Select figure to be modified
Gross  Net Net  Gross
or go to previous menu item.
Modify selected figure or go
Weight print mV load cell test
to next menu item
Confirm or enter in
Setting setpoint and hysteresis
submenu
Setting general parameters (press
+
immediately followed by )
Setting preset tare (press
+
immediately followed by )
Load distribution display

SYMBOL Function
net weight (semi-automatic tare or preset tare)
zero (deviation from zero not more than ±0.25 divisions)
stability
unit of measure: kg
unit of measure: g
not used

The symbols are activated in sequence within the menus to indicate that the display is
not showing a weight.

-8-
 MENU MAP

Into menus changes are applied right after pressing the ENTER key (no further confirmation is
required).

SETPOINT

     

…
  
…



SYSTEM PARAMETERS

 +  




    
3s
   
   
  
 
  
   
   
  

  
  
 
   
 
   
 
   
  

 
 
 
 
 
-9-
  




 

 

 



3s
 


  
 
 

 

 + 

- 10 -
 INSTRUMENT COMMISSIONING

Upon switch-on, the display shows in sequence:

-  →  (ONLY in case of approved program);
- instrument model (e.g.: );
-  followed by the software code (e.g.:  );
- program type:  (base);
-  followed by the software version (e.g.:  );
-  followed by the hardware code (e.g.:  );
- serial number (e.g.: );

Check that the display shows the weight and that when loading the load cells there is an increase in
weight. If there is not check and verify the connections and correct positioning of the load cells.

- If the instrument has already been theoretical CALIBRATED (plant system identification tag
present on the instrument and on the cover: load cell’s rated data already entered):
▫ If the system uses load cells with different sensitivity perform a real or theoretical equalization
(see section EQUALIZATION).
▫ Reset to zero (see section TARE WEIGHT ZERO SETTING).
▫ Check the calibration with sample weights and correct the indicated weight if necessary (see
section REAL CALIBRATION (WITH SAMPLE WEIGHTS)).

- If the instrument HAS NOT BEEN CALIBRATED (missing plant system identification tag)
proceed with calibration:
▫ If the system uses load cells with different sensitivity perform a real or theoretical equalization
(see section EQUALIZATION).
▫ If load cells data are unknown, follow the procedure in section REAL CALIBRATION (WITH
SAMPLE WEIGHTS).
▫ Enter the rated data of load cells following the procedure given in section THEORETICAL
CALIBRATION.
▫ Reset to zero (see section TARE WEIGHT ZERO SETTING).
▫ Check the calibration with sample weights and correct the indicated weight if necessary (see
section REAL CALIBRATION (WITH SAMPLE WEIGHTS)).

- If you use the analog output, set the desired analog output type and the full scale value (see
section ANALOG OUTPUT).
- If you use serial communication, set the related parameters (see section SERIAL
COMMUNICATION SETTING).
- If setpoint are used, set the required weight values and the relevant parameters (see sections
SETPOINT PROGRAMMING and OUTPUTS AND INPUTS CONFIGURATION).

- 11 -
 PROGRAMMING OF SYSTEM PARAMETERS

From the weight display, press simultaneously keys MENU and ESC to access the parameter setting.

MENU/ENTER: to enter a menu/confirm the data entry.

: to modify the displayed figure or menu item.
: to select a new figure or modify the displayed menu item.
ESC: to cancel and return to the previous menu.

THEORETICAL CALIBRATION

 +    

This function allows the load cell rated values to be set.

To perform the theoretical calibration set the following parameters in sequence:

-  (default: ): the system full scale is given by one cell capacity multiplied by the
number of cells used. Example: 4 cells of 1000 kg  FULL SCALE = 1000 x 4 = 4000.
The instrument is supplied with a theoretical full scale value  corresponding to 10000. To
restore factory values, set 0 as full scale.
-  (default: 2.00000 mV/V): sensitivity is a load cell rated parameter expressed in mV/V.
Set the average sensitivity value indicated on the load cells. It’s possible to set a value between
0.50000 and 7.00000 mV/V. Example of 4-cell system with sensitivity: 2.00100, 2.00150,
2.00200, 2.00250; enter 2.00175, calculated as (2.00100 + 2.00150 + 2.00200 + 2.00250) / 4.
- : the division (resolution) is the minimum weight increment value which can be
displayed. It is automatically calculated by the system according to the performed calibration, so
that it is equal to 1/10000 of full scale. It can be changed and be variable between 0.0001 and
100 with x1 x2 x5 x10 increments.

- By modifying the theoretical full scale, the sensitivity or the division, the real calibration
is cancelled and the theoretical calibration only is considered valid.
- If the theoretical full scale and the recalculated full scale in real calibration (see section
REAL CALIBRATION (WITH SAMPLE WEIGHTS)) are equal, this means that the
calibration currently in use is theoretical; if they are different, the calibration in use is the
real calibration based on sample weights.
- By modifying the theoretical full scale or the divisions, the system’s parameters
containing a weight value will be set to default values (setpoint, hysteresis, etc.).

- 12 -
 MAXIMUM CAPACITY

 +   

: maximum displayable weight (from 0 to max full scale; default: 0). When the weight exceeds
this value by 9 divisions, the display shows . To disable this function, set 0.

TARE WEIGHT ZERO SETTING

 +   

This menu may also be accessed directly from the weight display, holding down the 0
key for 3 seconds.

Perform this procedure after having set the THEORETICAL CALIBRATION data.

Use this function to set to zero the weight of the empty system after commissioning and then later
on to compensate zero variations due to the presence of product residues.
Procedure:
- Confirm the message  by pressing ENTER.
- The weight value to be set to zero is displayed. In this phase all of the symbols are flashing.
- Confirming once again, the weight is set to zero (the value is stored to the permanent memory).
- Press to display the value of the total weight reset by the instrument, given by the sum of all
of the previous zero settings.

DIAGNOSTICS ON ZERO: if diagnostics on zero has been enabled, the display shows the current
load distribution and the weight value; by pressing and , the stored load distribution and the
weight set to zero are displayed (if the weight is zero and all channels are , it means that no
zero-setting has yet been performed). Press ENTER and select  or   to store or not
the current distribution and the zero mV values (see section TEST). Confirm by pressing ENTER to
perform a new zero-setting.

WARNING: diagnostics on zero is performed only if the load distribution has been stored
at least once.

ZERO VALUE MANUAL ENTRY

 +    

WARNING: Perform this procedure only if it’s not possible to reset the weighed structure tare, for
example because it contains product that cannot be unloaded.
Set in this parameter the estimated zero value (from 0 to max 999999; default: 0).

- 13 -
 REAL CALIBRATION (WITH SAMPLE WEIGHTS)

 +   

After having performed the THEORETICAL CALIBRATION, EQUALIZATION and TARE WEIGHT
ZERO SETTING, this function allows correct calibration to be done using sample weights of
known value and, if necessary, any deviations of the indicated value from the correct value to
be corrected.

Load onto the weighing system a sample weight, which must be at least 50% of the maximum
quantity to be weighed.
By confirming the message  the flashing value of the weight currently on the system is
displayed. In this phase all of the symbols are off. Adjust the value on display by using the arrow
keys if necessary. After confirming, the new set weight will appear with all the symbols flashing.
After an additional confirmation, the message  will be restored and by repeatedly pressing
the key ESC the weight will once again be displayed.

Example: for a system of maximum capacity 1000 kg and 1 kg division, two sample weights are
available, one of 500 kg and the other one of 300 kg. Load both weights onto the system and correct
the indicated weight to 800. Now remove the 300 kg weight, the system must show 500; remove the
500 kg weight too; the system must read zero. If this does not happen, it means that there is a
mechanical problem affecting the system linearity.

WARNING: identify and correct any mechanical problems before repeating the procedure.

- If theoretical full scale and recalculated full scale in real calibration are equal, it means
that the theoretical calibration is currently in use; otherwise, the real calibration based on
sample weights is in use.
- If the correction made changes the previous full scale for more than 20%, all the
parameters with settable weight values are reset to default values.

LINEARISATION OPTION ON MAX 5 POINTS:

It is possible to perform a linearisation of the weight repeating the above-described procedure
up to a maximum of five points, using five different sample weights. The procedure ends by
pressing the ESC button or after entering the fifth value; at this point it will no longer be possible
to change the calibration value, but only to perform a new real calibration. To perform a new
calibration, should return to the weight display and then re-entering into the calibration menu.
By pressing after having confirmed the sample weight that has been set, the full scale appears,
recalculated according to the value of the maximum sample weight entered and making reference to
the cell sensitivity set in the theoretical calibration ().

- 14 -
 CONFIRMATION AND CHANGE OF ACTIVE CHANNELS

After performing the calibration and verifying that the system works properly, you can confirm the
channels automatically detected by the instrument; in this way, in case of accidental interruption of
the cable of one or more load cells, the instrument displays the  alarm.

 +    

 (default): confirmation is requested (),press ENTER to proceed or press ESC to

cancel. The display shows the number of channels automatically detected by the instrument, press
ENTER to confirm and save the current selection or press ESC to exit with no change.
 confirmation is requested (),press ENTER to proceed or press ESC to cancel.
Press or to select the channel, confirm with ENTER and press or to activate ()or
deactivate it (); press ESC to save the current selection and exit.

After editing, you must repeat equalization, zero setting and calibration using a sample
weight.

- 15 -
 EQUALIZATION

At the end of the equalization you must perform the TARE WEIGHT ZERO SETTING
and, if necessary, the REAL CALIBRATION.

REAL EQUALIZATION

 +    

Use a sample weight equal to at least 50% of the single load cell capacity.

: unload the scale, wait for stability and confirm by pressing ENTER.
: place the sample weight on load cell 1, wait for stability and confirm by pressing ENTER.
: place the sample weight on load cell 2, wait for stability and confirm by pressing ENTER.
Repeat the operation for each connected load cell.
If equalization is successfully completed, the display shows , confirm by pressing ENTER to
exit; if an error occurs, the display shows , confirm by pressing ENTER and repeat the
procedure.

THEORETICAL EQUALIZATION

 +    

  ÷  : set the sensitivity for each load cell, leaving it at 0 for non-active channels.

EQUALIZATION COEFFICIENTS

 +     

  ÷  : it displays the equalization coefficients calculated for each active channel.

EQUALIZATION DELETION

 +    

Confirmation is requested (), press ENTER to reset the equalization or press ESC to cancel
the command.

- 16 -
 FILTER ON THE WEIGHT

 +  

Setting this parameter allows a stable weight display to be obtained.
To increase the effect (weight more stable) increase the value (from 0 to 9, default 4).
As seen in the diagram:
- By confirming the  message, the currently programmed filter value is displayed.
- By changing and confirming the value, the weight is displayed and it will be possible to
experimentally verify its stability.
- If stability is not satisfactory, confirming brings back the message  and the filter may be
modified again until an optimum result is achieved.

The filter enables to stabilise a weight as long as its variations are smaller than the corresponding
“response time”. It is necessary to set this filter according to the type of application and to the full
scale value set.

FILTER VALUE Response times Display and serial port refresh

[ms] frequency
[Hz]
0 12 300
1 150 100
2 260 50
3 425 25
4 (default) 850 12.5
5 1700 12.5
6 2500 12.5
7 4000 10
8 6000 10
9 7000 5
A 6 600

The "A" filter can only be set if the instrument is connected to one load cell only.

ANTI PEAK

When the weight is stable, the anti peak filter removes any sudden disturbances with a maximum duration
of 1 second. Confirm the filter on the weight with ENTER and select one of the following options:
- : anti peak filter enabled (default);
- : anti peak filter disabled.

- 17 -
 ZERO PARAMETERS

 +   

RESETTABLE WEIGHT SETTING FOR SMALL WEIGHT CHANGES

  (from 0 to max full scale; default: 300; considered decimals: 300 – 30.0 – 3.00 – 0.300): this
parameter indicates the maximum weight value resettable by external contact, keypad or serial
protocol.

AUTOMATIC ZERO SETTING AT POWER-ON

  (from 0 to max 20% of full scale; default: 0): If at switch-on the weight value is lower than
the value set in this parameter and does not exceed the   value, the weight is reset. To
disable this function, set 0.

ZERO TRACKING

  (from 1 to 5, default: ): When the weight value is stable and, after a second, it
deviates from zero by a figure in divisions smaller or equal to the figure in divisions set in this
parameter, the weight is set to zero. To disable this function, set .
Example: if the parameter  is set to 5 and   is set to 2, the weight will be
automatically set to zero for variations smaller than or equal to 10 ( x  ).

- 18 -
 SETTING UNITS OF MEASURE

 +   

These are the available units of measure:

: kilograms
: grams
: tons
: pounds*
: newtons*
: litres*
: bars*
: atmospheres*
: pieces*
: newton metres*
: kilogram metres*
: other generic units of measure not included in the list*

If the print function is enabled, the symbol corresponding to the selected unit of measure will be
printed after the measured value.

For the units marked with * it’s possible to set also the display coefficient (parameter
, see the related section). To use  is necessary to enable it, closing the
 input (see section OUTPUTS AND INPUTS CONFIGURATION).

DISPLAY COEFFICIENT

 +   

By setting the coefficient  the display is changed accordingly.

If one of the inputs is set to  mode (see section OUTPUTS AND INPUTS
CONFIGURATION) when the input is closed the value will be displayed modified according to the
 coefficient; when the input is opened the standard weight display will be restored.

: (max settable value: 99.9999; default: 1.0000) will have different meanings according to the
value set in , i.e. the selected unit of measure. (see section SETTING UNITS OF MEASURE).

- 19 -
If the unit of measure chosen is:
: pounds, the value set in  will be multiplied by the weight value currently displayed;
: newton, the value set in  will be multiplied by the weight value currently displayed;
: litres, in  set the specific weight in kg/l, assuming that the system is calibrated in kg;
: bar, the value set in  will be multiplied by the weight value currently displayed;
: atmosphere, the value set in  will be multiplied by the weight value currently displayed;
: pieces, in  set the weight of one piece;
: newton metres, the value set in  will be multiplied by the weight value currently
displayed;
: kilogram metres, the value set in  will be multiplied by the weight value currently
displayed;
: generic unit of measure not included in the list, the value set in  will be multiplied by
the weight value currently displayed.

WARNING: All other settings (setpoint, hysteresis, calibration ...) are expressed in weight
value. If you want to convert them to the new unit of measurement, perform one of the
following procedures for changing the system calibration.
The parameter  must remain set to 1.0000.

THEORETICAL CALIBRATION’S CHANGE FOR OTHER UNITS OF MEASURE

Set in the parameter  the F.SCALE value divided by the conversion coefficient from kg to
the new unit of measure.
Example: The 4 load cells of 1000 kg are placed under a scale for olive oil, which has a specific
gravity of 0.916 kg/l. Setting the F.SCALE = (4 x 1000) / 0.916 = 4367, the system works in liters of
olive oil. Also, if you set the parameter  =  (see section SETTING UNITS OF
MEASURE), the system will display and print the symbol “l” instead of “kg”.

REAL CALIBRATION’S CHANGE FOR OTHER UNITS OF MEASURE

Load a known quantity of product litres on the scale (equal to at least 50% of the maximum amount
that you must weigh) and enter in the parameter , the product loaded value in litres. Also, if
you set the parameter  =  (see section SETTING UNITS OF MEASURE), the system
will display and print the symbol “l” instead of “kg”.

- 20 -
 OUTPUTS AND INPUTS CONFIGURATION

 +      

… …

   
OUTPUTS
The outputs are set by default as follows:  /  /  /  / .
Possible operation modes:
-  (normally open): the relay is de-energised and the contact is open when the weight is
lower than the programmed setpoint value; it closes when the weight is higher than or equal to
the programmed setpoint value.
-  (normally closed): the relay is energised and the contact is closed when the weight is
lower than the programmed setpoint value; it opens when the weight is higher than or equal to
the programmed setpoint value.

- : the contact will switch on the basis of weight, according to setpoint (see section SETPOINT
PROGRAMMING).
- : the contact will not switch on the basis of weight, but is controlled by remote protocol
commands.
- : relay switching occurs when the weight is stable.
- : relay switching occurs when one of the following alarms is triggered: , ,
,  ,  , ,  ; the operation mode is forced to  (normally
closed).

If the operation mode  is selected, the following options are also active:
- : the contact will switch on the basis of gross weight.
- : the contact will switch on the basis of net weight (If the net function is not active, the
contact will switch on the basis of gross weight).

- : relay switching occurs for both positive and negative weight values.
- : relay switching occurs for positive weight values only.
- : relay switching occurs for negative weight values only.
By confirming with ENTER the setpoint operation can be set to the value 0:
- : relay switching will not occur if the setpoint value is 0.
- :
- setpoint = 0 and switching = : relay switching occurs when the weight is 0; the
relay will switch again when the weight is different from zero, taking hysteresis into
account (both for positive and for negative weights).
- setpoint = 0 and switching = : relay switching occurs for a weight higher than or equal
to 0, the relay will switch again for values below 0, taking hysteresis into account.
- setpoint = 0 and switching = : relay switching occurs for a weight lower than or equal
to 0, the relay will switch again for values above 0, taking hysteresis into account.

- 21 -
 INPUTS
Default: input 1 =  input 2 =  input 3 = 

Possible operation modes:

-  (NET/GROSS): by closing this input for no more than one second, it’s making an
operation of SEMI-AUTOMATIC TARE and the display will show the net weight. To display the
gross weight again, hold the NET/GROSS input closed for 3 seconds.
- : by closing the input for no more than one second, the weight is set to zero (see section
WEIGHT ZERO-SETTING FOR SMALL VARIATIONS (SEMI-AUTOMATIC ZERO)).
- : keeping the input closed the maximum weight value reached remains on display. Opening
the input the current weight is displayed.
- : closing the input no operation is performed, the input status may however be read remotely
by way of the communication protocol.
- : closing the input for max one second the weight is transmitted over the serial
connection according to the fast continuous transmission protocol only once (only if  is
set in the item ).
- : when the input is closed the weight is displayed based on the set coefficient (see setting
of the units of measure and coefficient), otherwise the weight is displayed.
- : when the input is closed the data are sent for printing if in the communication protocol
of either serial port the parameter  is set.

SEMI-AUTOMATIC TARE (NET/GROSS)

THE SEMI-AUTOMATIC TARE OPERATION IS LOST UPON INSTRUMENT POWER-

OFF.

To perform a net operation (SEMI-AUTOMATIC TARE), close the NET/GROSS input or press the
TARE key for less than 3 seconds. The instrument displays the net weight (just set to zero) and the
NET symbol lights up. To display the gross weight again, keep the NET/GROSS input closed or
press TARE for 3 seconds.
This operation can be repeated many times by the operator to allow the loading of several products.

Example:
Put the box on the scale, the display shows the box weight; press TARE, the display shows the net
weight to zero; introduce the product in the box, the display shows the product weight. This
operation can be repeated several times.

While the net weight is displayed, keep pressed to display gross weight. When
the key is released the net weight will be displayed again.

The semi-automatic tare operation is not allowed if the gross weight is zero (the display
shows ).

- 22 -
 PRESET TARE (SUBTRACTIVE TARE DEVICE)

 + 
It is possible to manually set a preset tare value to be subtracted from the display
value provided that the  ≤ max capacity condition is verified.

By default the instrument shows the last programmed preset tare value: to apply it press and
then ENTER.
After setting the tare value, going back to the weight display, the display shows the net weight
(subtracting the preset tare value) and the NET symbol lights up to show that a tare has been
entered. To delete a preset tare and return to gross weight display, hold down TARE for about 3
seconds or keep the NET/GROSS input (if any) closed for the same length of time (3 seconds). The
preset tare value is set to zero. The NET symbol is turned off when the gross weight is displayed
once again.

While the net weight is displayed, keep pressed to display the gross weight.
When the key is released the net weight will be displayed again.

- IF A SEMI-AUTOMATIC TARE (NET) IS ENTERED, IT IS NOT POSSIBLE TO

ACCESS THE ENTER PRESET TARE FUNCTION.
- IF A PRESET TARE IS ENTERED, IT’S STILL POSSIBLE TO ACCESS THE SEMI-
AUTOMATIC TARE (NET) FUNCTION. THE TWO DIFFERENT TYPES OF TARE ARE
ADDED.

ALL THE SEMI-AUTOMATIC TARE (NET) AND PRESET TARE FUNCTIONS WILL BE
LOST WHEN THE INSTRUMENT IS TURNED OFF.

SEMI-AUTOMATIC ZERO (WEIGHT ZERO-SETTING FOR SMALL VARIATIONS)

By closing the SEMI-AUTOMATIC ZERO input, the weight is set to zero; alternatively, by pressing
the 0 key for less than 3 seconds, the  message is displayed for 3 seconds, by
pressing ENTER the weight is set to zero.
This function is only allowed if the weight is lower than the   value (see section
RESETTABLE WEIGHT SETTING FOR SMALL WEIGHT CHANGES), otherwise the alarm
 appears and the weight is not set to zero.

The zero-setting is lost upon instrument power-off.

- 23 -
 PEAK

By keeping the PEAK input closed the maximum weight value reached remains displayed. By
opening the input the current weight is displayed.

If you wish to use this input to view a sudden variation peak, set the FILTER ON THE
WEIGHT to 0.

ANALOG OUTPUT

 +  

- : it selects the analog output type (4÷20 mA, 0÷20 mA, 0÷10 V, 0÷5 V; default: 4÷20 mA).
- : choice of a weight followed by the analog output: gross () or net (). If the net
function is not active, the analog output varies according to gross weight.
-  : set the weight value for which you wish to obtain the minimum analog output value.

Only set a value different from zero if you wish to limit the analog output range; for
instance: for a full scale value of 10000 kg you require an 4 mA signal at 5000 kg and
20 mA at 10000 kg, in this case, instead of zero, set 5000 kg.

-  : set the weight value for which you wish to obtain the maximum analog output value; it
must correspond to the value set in the PLC program (default: calibration full scale). E.g.: if I am
using a 4÷20 mA output and in the PLC program I wish to have 20 mA = 8000 kg, I will set the
parameter to 8000.
-  : analog output correction to zero: if necessary adjust the analog output, allowing the PLC
to indicate 0. The sign “-“ can be set for the last digit on the left. E.g.: if I use a 4÷20 mA output
and, with the minimum analog setting, the PLC or tester read 4.1 mA, I must set the parameter to
3.9 to obtain 4.0 on the PLC or tester.
-  : correction of analog output to full scale: if necessary permit modification of the analog
output by allowing PLC to indicate the value set in the parameter  . E.g. if I am using a
4÷20 mA output with the analog set to full scale and the PLC or tester reads 19.9 mA, I must set
the parameter to 20.1 to get 20.0 on the PLC or tester.

Minimum and maximum values which can be set for zero and full scale corrections:
ANALOG OUTPUT TYPE Minimum Maximum
0÷10 V -0.150 10.200
0÷5 V -0.150 5.500
0÷20 mA -0.200 22.000
4÷20 mA -0.200 22.000

- 24 -
NOTE: the analog output may also be used in the opposite manner, i.e. the weight setting that
corresponds to the analog zero ( ) may be greater than the weight set for the analog full scale
( ). The analog output will increase towards full scale as the weight decreases; the analog
output will decrease as the weight increases.

For example:
  = 10000   = 0 analog output 0÷10 V

Weight = 0 kg analog output = 10 V

Weight = 5000 kg analog output = 5V
Weight =10000 kg analog output = 0V

All analog outputs of the instrument are ACTIVE and SINGLE ENDED type, therefore
they can be connected only to PASSIVE receiver devices. The minimum load allowed for
voltage outputs is 2 kohm, the maximum load allowed for current outputs is 400 ohm.

Voltage or current analog signal

ACTIVE
PASSIVE
ANALOG - COMMON RECEIVER
OUTPUT

SERIAL COMMUNICATION SETTING

 +   

- : it disables any type of communication (default).

- : MODBUS-RTU protocol; possible addresses: from 1 to 99 (see Communication
protocols manual).
- : ASCII bidirectional protocol; possible addresses: from 1 to 99 (see Communication
protocols manual).
- 
-  
- : continuous weight transmission protocol (see Communication protocols manual), at the
frequency set in  item (from 10 to 300).
-   (set:  = ,  = ).
-   (set:  = ,  = ).
- : continuous weight transmission protocol to RIP5/20/60, RIP50SHA, RIPLED series remote
displays; the remote display shows the net weight or gross weight according to its settings (set:
 = ,  = ,  = ).
- : continuous weight transmission protocol to RIP6100, RIP675, RIP6125C series remote
displays; the remote display shows the net weight or gross weight according to its settings (set:
 = ,  = ,  = ).

- 25 -
- : continuous weight transmission protocol to RIP6100, RIP675, RIP6125C series remote
displays (set:  = ,  = ,  = ).
When the remote display is set to gross weight:
- if the instrument displays the gross weight, the remote display shows the gross weight.
- if the instrument shows the net weight, the remote display shows the net weight alternated
with the message .
- : printer.
- : communication protocol with inclinometer (see Inclinometer manual).

- : transmission speed (2400, 4800, 9600, 19200, 38400, 115200; default: 9600).
- : instrument address (from 1 to 99; default: 1).
- : maximum transmission frequency (10 – 20 – 30 – 40 – 50 – 60 – 70 – 80 – 100 –
200 – 300; default: 10); to be set when the  transmission protocol is selected.
Maximum setting frequency ():
- 20 Hz with minimum baud rate 2400 baud.
- 40 Hz with minimum baud rate 4800 baud.
- 80 Hz with minimum baud rate 9600 baud.
- 100 Hz with minimum baud rate 19200 baud.
- 200 Hz with minimum baud rate 38400 baud.
- 300 Hz with minimum baud rate 38400 baud.
- : delay in milliseconds which elapses before the instrument replies (from 0 to 200
ms; default: 0).
- :
- : no parity (default).
- : even parity.
- : odd parity.
- : stop bit (1 – 2; default: 1).
-  : stability character ( – ; default: ); to be set when the 
transmission protocol is selected in   mode (see section CONTINUOUS FAST
WEIGHT TRANSMISSION PROTOCOL in Protocols manual).
- : number of copies(1 – 9; default: 1).
- : number of blank lines between one printout and the next.
- : printing of custom heading from PC ( – ; default: ).
- : connected printer type:
- 
- 
- 

For more information about protocols and methods of communication, request the
proper manual to technical assistance.

- 26 -
 RS485 SERIAL COMMUNICATION

INSTRUMENT INSTRUMENT INSTRUMENT

GND

GND

GND
RS485 +

RS485 +

RS485 +
RS485 -

RS485 -

RS485 -
max 500 m

24 VDC
-
+
PC RS232

VIN TX+ RS485 + RS485 +

3 2 5

0 TX- RS485 - RS485 -

TX CONVLAU RX+
RX RX-

If the RS485 network exceeds 100 metres in length or baud-rate

over 9600 are used, two terminating resistors are needed at the
ends of the network: close the two jumpers indicated in the picture
on the furthest instruments. Should there be different instruments
or converters, refer to the specific manuals to determine whether it
is necessary to connect the above-mentioned resistors.

DIRECT CONNECTION BETWEEN RS485 AND RS232 WITHOUT CONVERTER

Since a two-wire RS485 output may be used directly on the RS-232 input of a PC or remote display
or printer, it is possible to implement instrument connection to an RS-232 port in the following
manner:

INSTRUMENT RS232
RS485 – → RXD
RS485 + → GND

This type of connection allows A SINGLE instrument to be used in a ONE WAY

mode.

- 27 -
 AUTOMATIC DIAGNOSTICS OF LOAD DISTRIBUTION

 +  

Only use this function in systems where load distribution can be repeated with each
change of weight (for example: liquid weighing).

-  (/; default: ): it enables load diagnostics.

- : it displays the active channels status (weight, load percentage on each channel,
enabled channels and/or channels in error).
- : it displays stored load distributions (weight, load percentage on each channel).
- : it deletes stored load distributions; confirmation is requested (),press ENTER to
proceed or press ESC to cancel.
-  (default: 5.0): difference between the current and stored percentage beyond which the
 alarm is triggered.
-   (/; default: ): it enables diagnostics on zero.
-  (default: 5.0): difference between the current and stored percentage beyond which the
 alarm is triggered.
-  : it displays current load distribution on zero and the one previously stored (weigh, load
percentage on each channel).

Load diagnostics: the instrument, with stable weight, calculates and stores the load percentage on
each channel. If under normal operation the load percentage error is higher than the value set in
parameter , the display shows the  alarm alternated with the weight; the alarm
remains active also upon instrument power-off, press ENTER to cancel.

Diagnostics on zero: when a zero-setting is performed from the  menu, the instrument
calculates the load percentage on each channel; diagnostics on zero is performed only if the load
distribution has been stored at least once (see section TARE WEIGHT ZERO SETTING).
If with unloaded system the load percentage error is higher than the value set in parameter
, the display shows the  alarm alternated with the weight; the alarm remains active
also upon instrument power-off, press ENTER to cancel.

Example of current load distribution display: the top of the display

shows the weight on the scale; the bottom shows the load
percentage on each active channel.
This screen can also be accessed directly from the weight display
by pressing the TEST key.

- 28 -
 TEST

 +  

- Load distribution:
: it displays the active channels status (weight, load percentage on each channel,
enabled channels and/or channels in error). This menu can also be accessed directly from
the weight display by pressing the TEST key.
- Input Test:
: ensure that for each open input  is displayed,  is displayed when the input is closed.
- Output Test:
: setting  ensure that the corresponding output opens. Setting  ensure that the
corresponding output closes.
- Analog Output Option Test:
: It allows the analog signal to range between the minimum and the maximum values
starting from the minimum.
: current output test.
: voltage output test.
- Millivolt Test:
: it displays the response signal of each load cell expressed in mV with three
decimals.
- Millivolt stored at zero setting (only if   = ):
: it displays the response signal of each load cell, expressed in mV with three
decimals (see section TARE WEIGHT ZERO SETTING)

- 29 -
 EVENTS LOG

 +  

The instrument can store up to 50 events; the oldest records are overwritten.

-  : it displays the last 50 events stored, starting from the most recent one:
: zero-setting from the calibration menu, press ENTER to display the value set to zero.
: theoretical calibration, press ENTER to display the full scale set.
: real calibration, press ENTER to display the sample weight used.
: tare setting via the keypad, press ENTER to display the set value.
: load distribution error, press ENTER to display the weight value that triggered the
alarm, press ENTER again to display the difference between the load percentage and the
stored value.
: weight alarm, press ENTER to display the alarm type.
: load distribution deletion.
: equalization.
: modification or deletion of the manual selection of active channels.
-  : it deletes stored events; confirmation is requested (),press ENTER to proceed
or press ESC to cancel.
-  : it prints all events.

INFO MENU

 +  

: the identification data of the instrument are displayed.
- : instrument model
-   : software code
- : program type
-  : software version
-  : serial number

- 30 -
 SETPOINT PROGRAMMING

From the weight display, press MENU to access the setpoint setting.

MENU/ENTER: to enter a menu/confirm the data entry.

: to modify the displayed figure or menu item.
: to select a new figure or modify the displayed menu item.
ESC: to cancel and return to the previous menu.

     

…
  
…



-  (from 0 to max full scale; default: 0): setpoint; relay switching occurs when the weight
exceed the value set in this parameter. The type of switching is settable (see section OUTPUTS
AND INPUTS CONFIGURATION).

-  (from 0 to max full scale; default: 0): hysteresis, value to be subtracted from the setpoint
to obtain contact switching for decreasing weight. For example with a setpoint at 100 and
hysteresis at 10, the switching occurs at 90 for decreasing weight.

These values are set to zero if the calibration is changed significantly (see sections
THEORETICAL CALIBRATION and REAL CALIBRATION (WITH SAMPLE WEIGHTS)).

- 31 -
 USE WITH W SERIES INSTRUMENTS

WARNING: the weight indicator must be properly configured before operating in

combination with the multi-channel weight transmitter (see section DATA DELETION
AND PROGRAM SELECTION in W serie instrument manual) and the approval status
set on both instruments must be the same.

When the TLM8 is used in combination with a W serie instrument, the load cells are connected to
the multi-channel weight transmitter, which transmits the weight to the indicator; all the operations of
calibration, zeroing, equalization and channel selection can be performed remotely through the
indicator.

CONNECTION TO THE WEIGHT INDICATOR

Connection via RS485 port. SIGNAL TLM8 Weight indicator

RS485 + 39 RS485 +
RS485 - 40 RS485 -
SHIELD 42 SHIELD

Weight indicator configuration

Configure, on the serial port used, the  protocol with the following parameters:
 =   =   = 

TLM8 multi-channel weight transmitter configuration

Configure, on the serial port used, the MODBUS protocol with the following parameters:
 =   =   = 

- 32 -
 ADDITIONAL MENU MAP

WARNING: the map shows only the additional menu items that are enabled on the W
series instruments connected to the TLM8.

Into menus changes are applied right after pressing the ENTER key (no further confirmation is
required).

 ENTER + ESC  

    

 
  

   

 




 

 

 



  
 
 

- 33 -
 TLM8 REMOTE CONTROL

The following functions of TLM8 can be performed remotely through the weight indicator:

 INSTRUMENT COMMISSIONING
 TARE WEIGHT ZERO SETTING
 CONFIRMATION AND CHANGE OF ACTIVE CHANNELS
 EQUALIZATION
 FILTER ON THE WEIGHT
 ANTI-PEAK
 AUTOMATIC DIAGNOSTICS OF LOAD DISTRIBUTION
 LOAD DIAGNOSTICS
 DIAGNOSTICS ON ZERO
 TEST
 EVENTS LOG

WARNING: when using the weight indicator to manage the multi-channel

instrument, the weight indicator display replicates exactly what would be
displayed on the TLM8 display.

If the configuration is performed on the TLM8, the W series instrument connected must be
restarted to allow synchronization.

REMOTE KEYPAD LOCKING

 ENTER + ESC  
: keypad locked.
: keypad unlocked.

ADDITIONAL ALARMS

WARNING: the list shows only the additional alarms that are enabled on the W series
instruments connected to the TLM8.

 : TLM8 is not responding, check connections and serial ports settings.
 : TLM8 responds incorrectly, check connections and serial ports settings.
: issues with the serial communication device.
: the instrument is synchronizing with TLM8, wait for the end of the operation.

- 34 -
 ALARMS

: no load cell detected, check the connections.

: the load cell signal exceeds 39 mV; the conversion electronics (AD converter) is
malfunctioning.
: the load cell excitation is not connected or is incorrectly connected; the references are
not connected or are incorrectly connected; the load cell is a 4-wire and there are no
jumpers between EX- and REF- and between EX+ and REF+.
: the load cell is not connected or is incorrectly connected (the number indicates the
channel on which the error is detected).
 : the weight display exceeds 110% of the full scale.
 : internal instrument converter failure; check load cell connections, if necessary contact
technical assistance.
: the weight exceeds the maximum capacity by 9 divisions.
 : maximum displayable value exceeded (value higher than 999999 or lower than -999999).
: weight too high: zero setting not possible.
: this message appears in the sample weight setting, in real calibration, after the fifth
sample weight value has been entered.
: the value set for the parameter is beyond the permitted values; press ESC to quit the
setting mode leaving the previous value unchanged. Examples: a number of decimals is
selected for full scale which exceeds the instrument's display potential; value above the
maximum setting value; the weight value set in sample weight verification does not match
the detected mV increase; the analog output correction goes beyond the permitted limits.
: lock active on menu item, keypad or display.
: It’s not possible to display properly the number because is greater than 999999 or less
than -999999.
: the current load cell has already been equalized; press ENTER to go back to the
previous step and move the sample weight on the next load cell.
: the sample weight was not loaded or is too light.
: the load percentage error is higher than the value set in parameters  or ;
press ENTER to cancel the alarm.
: gross weight equal to zero: the semi-automatic tare operation cannot be performed.
 : issues with the fieldbus device.

- 35 -
Serial protocol alarms:
        
MODE
Bit LSB 76543210 76543210 76543210 76543210 76543210 The response to the
xxxxxxx1 xxxx1xxx xxxxxx1x xxxxx1xx On gross: zero command is a
Status 'value not valid' error
xxx1xxxx
Register (error code 3)
On net:
MODBUS RTU
xx1xxxxx
ASCII __O-F_ __O-L_ __O-F_ __O-L_ __O-F_ &aa#CR
RIP * __O-F_ __O-L_ __O-F_ __O-L_ __O-F_ __O-F_
HDRIP-N _ERCEL _ER_OL _ER_AD ###### _ER_OF O__SET
CONTIN _ERCEL _ER_OL _ER_AD ^^^^^^ _ER_OF O__SET
* For RIP remote displays, if the message exceeds 5 digits the display reads .

With an alarm the relays open and the analog outputs go to the lowest possible value
according to the following table:
RANGE 0÷20 mA 4÷20 mA 0÷5 V 0÷10 V
Output value -0.2 mA 3.5 mA -0.5 V -0.5 V

- 36 -
 PRINTING EXAMPLES

If the printer has been set (see section SERIAL COMMUNICATION SETTINGS), from the weight
display press the PRINT key:

BASIC PRINTOUT
-----------------------
TLM8 BASE Addr:01

GROSS 878 kg
NET 589 kg
TARE 289 kg

BASIC PRINTOUT (PEAK ENABLED):

-----------------------
TLM8 BASE Addr:01

GROSS 1204 kg
NET 831 kg
TARE 373 kg
PEAK 2103 kg

PRINTOUT WITH  ENABLED:

-----------------------
TLM8 BASE Addr:01

UNIT kg | bar
G 1195 | 1792
N 1195 | 1792
T 0 | 0

- 37 -
LOAD DISTRIBUTION PRINT
Current distribution: press the PRINT key from the  menu.
Current and stored distribution: from the   and  menus, keep pressed the PRINT key
for more than 3 seconds while the weight is displayed.

CURRENT DISTRIBUTION
-----------------------
TLM8 BASE Addr:01
CURRENT (STATUS)
GROSS 2014 kg
CH1: 23.5 %
CH2: 24.1 %
CH3: 15.5 %
CH4: 16.7 %
CH5: 9.0 %
CH6: 10.2 %
CH7: ERR (load cell connected but in error)
CH8: OFF (load cell not connected)

CURRENT AND STORED DISTRIBUTION

-----------------------
TLM8 BASE Addr:01
STORED (MEMRIP)
GROSS 2014 kg
CH1: 23.5 %
CH2: 24.1 %
CH3: 15.5 %
CH4: 16.7 %
CH5: 9.0 %
CH6: 10.2 %
CH7: ERR (load cell connected but in error)
CH8: OFF (load cell not connected)
GROSS OLD 2050 kg
CH1: 25.5 %
CH2: 22.1 %
CH3: 16.5 %
CH4: 16.7 %
CH5: 9.0 %
CH6: 10.2 %
CH7: ERR (load cell connected but in error)
CH8: OFF (load cell not connected)

- 38 -
 RESERVED FOR THE INSTALLER

MENU LOCKING

Through this procedure, it’s possible to block the access to any menu on the instrument.
Select the menu that you wish to lock:
  press ESC and simultaneously for 3 seconds, the display shows
 (the left point on the text indicates that this menu item is now locked). If the operator tries

to enter this menu, the access is denied and the display shows  .

MENU UNLOCKING

  press ENTER and simultaneously for 3 seconds, the display shows
 (the left point on the text is off to indicate that this menu item is unlocked).

TEMPORARY MENU UNLOCKING

  press and simultaneously for 3 seconds: it is now possible to enter
and modify all menus including those which are locked. By returning to weight display, the menu
lock is restored.

DATA DELETION AND PROGRAM SELECTION

WARNING: operations must only be performed after contacting technical assistance.

After each operation the display shows , press ENTER to continue.
By pressing ESC the procedure is cancelled and no changes are made.

Upon instrument power-on hold down the ESC key until the display shows , then proceed as
follows:

CONSTANTS RESTORE (does not erase the calibration): confirm , use arrow keys to select
, set code 6935 and confirm.

- 39 -
PROGRAM SELECTION: confirm  and use the arrow keys to select the desired program:
: basic program, setpoint management only.
: to be used when the loaded weighing system correspond to not loaded cells and vice versa
(product increases while weight on load cells actually decreases).
: weight remote display program with setpoint.

After confirming the choice of the program (except  and ), the user must choose its
approval status among the following possible choices:

: not approved program;

: approved program, single interval (Dir. 2014/31/EU, art. 1)*;
: approved program, multi-interval (Dir. 2014/31/EU, art. 1)*;
: approved program, multiple range (Dir. 2014/31/EU, art. 1)*;

*) Contact technical assistance to request the proper manual and the correct procedures for
approval, indicating mandatory hardware code and serial number (see section
INSTRUMENT COMMISSIONING).

When the TLM8 is used in combination with a W serie instrument, the approval status set
on both devices must be the same.

By confirming, the instrument is restored to default and data is erased.

If you do not have a specific manual for the newly set program, you can request it
to technical assistance.

KEYPAD OR DISPLAY LOCKING

Press ESC immediately followed by hold them down for about 5 seconds (this operation is also
possible via the MODBUS and ASCII protocols):

- : no lock.
- : keypad lock: if active, when a key is pressed the message  is displayed for 3
seconds.
- : keypad and display lock: if active, the keypad is locked and the display shows the
instrument model (weight is not displayed); by pressing a key the display shows  for 3
seconds.

- 40 -
 DECLARATION OF CONFORMITY - EU

SISTEMI DI PESATURA INDUSTRIALE - CELLE DI CARICO

Sistema di gestione
Qualità certificato
UNI EN ISO 9001:2008

CERTIFICAZIONE DEL SISTEMA DI GARANZIA DELLA QUALITÀ DELLA PRODUZIONE

email: [email protected] web: http://www.laumas.com

LAUMAS Elettronica S.r.l.
Tel. (+39) 0521 683124 - Fax (+39) 0521 681091 Fabbricante metrico Prot. N. 7340 Parma - R.E.A. PR N. 169833 - Reg. Imprese
Via 1° Maggio 6 – 43022 Montechiarugolo (PR) Italy PR N.19393 - Registro Nazionale Pile N° IT09060P00000982 - Registro A.E.E.
C.F. - P.IVA IT01661140341 N° IT08020000002494 - N. Mecc. PR 008385 - Cap. Soc. Euro 10.400 int. vers.

Dichiarazione di Dichiariamo che il prodotto al quale la presente dichiarazione si riferisce è conforme alle norme di
I
conformità seguito citate.
Declaration of We hereby declare that the product to which this declaration refers conforms with the following
GB
conformity standards.
Declaración de Manifestamos en la presente que el producto al que se refiere esta declaración está de acuerdo con
E
conformidad las siguientes normas
Wir erklären hiermit, dass das Produkt, auf das sich diese Erklärung bezieht, mit den nachstehenden
D Konformitäts-erklärung
Normen übereinstimmt.
Déclaration de Nous déclarons avec cela responsabilité que le produit, auquel se rapporte la présente déclaration, est
F
conformité conforme aux normes citées ci-après.
Tímto prohlašujeme, že výrobek, kterého se toto prohlášení týká, je v souladu s níže uvedenými
CZ Prohlášení o shode
normami.
Wij verklaren hiermede dat het product, waarop deze verklaring betrekking heeft, met de hierna
NL Conformiteit-verklaring
vermelde normen overeenstemt.
Declaração de Declaramos por meio da presente que o produto no qual se refere esta declaração, corresponde às
P
conformidade normas seguintes.
Niniejszym oświadczamy, że produkt, którego niniejsze oświadczenie dotyczy, jest zgodny z
PL Deklaracja zgodności
poniższymi normami.
Заявление о Мы заявляем, что продукт, к которому относится данная декларация, соответствует
RUS
соответствии перечисленным ниже нормам.

Models: TLM8

Mark Applied EU Directive Standards

2014/35/EU Not Applicable (N/A) for VDC type
Low Voltage Directive EN 61010-1:2010 for 230/115 VAC type
EN 55022:2010
EN 61000-6-2:2005
EN 61000-6-4:2007
2014/30/EU EN 61000-4-2:2009
EMC Directive EN 61000-4-3:2006+A2:2010
EN 61000-4-4:2012
EN 61000-4-5:2014
EN 61000-4-6:2014

M 2014/31/EU
NAWI Directive
EN 45501:2015
OIML R76-1:2006
(only if “M” mark is applied)

Montechiarugolo (PR), 26/10/2018 LAUMAS Elettronica s.r.l.

M. Consonni
(Legal Representative)

- 41 -