Scribd
Upload
18 views12 pages

CN 4-10

The document describes steps to create a network topology with two routers and configure static and RIP routing. It outlines connecting PCs, switches and routers and configuring IP addresses and static routes on each router.

Uploaded by

makanijenshi2409
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
18 views12 pages

CN 4-10

The document describes steps to create a network topology with two routers and configure static and RIP routing. It outlines connecting PCs, switches and routers and configuring IP addresses and static routes on each router.

Uploaded by

makanijenshi2409
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 12

Enrollment No: 202203103510061

Practical-4
Aim:

To perform a practical to create a topology and configure router using Static Routing

SoftwareUsed:

1. CiscoPacketTracer(WriteVersion)

2. Windows 7

Description:

Step-1: Select four PC from end device, and tack two switches and two router.

Step-2: Connect pc-switch-router with copper straight-through wire, and connection between
two routers with copper cross-over.

UTU/CGPIT/IT/SEM-4/ComupterNetworks 13
Enrollment No: 202203103510061

Step-3: Add ip address and default gateway in IP Configuration of PC0.

Step-4: Add ip address and default gateway in IP Configuration of PC1.

UTU/CGPIT/IT/SEM-4/ComupterNetworks 14
Enrollment No: 202203103510061

Step-5: Add ip address and default gateway in IP Configuration of PC2.

Step-6: Add ip address and default gateway in IP Configuration of PC3.

UTU/CGPIT/IT/SEM-4/ComupterNetworks 15
Enrollment No: 202203103510061

Step-7: Configure fastethernet0/0 of Router0.

Step-8: Configure fastethernet1/0 of Router0.

UTU/CGPIT/IT/SEM-4/ComupterNetworks 16
Enrollment No: 202203103510061

Step-9: Configure fastethernet0/0 of Router1.

Step-10: Configure fastethernet1/0 of Router0.

UTU/CGPIT/IT/SEM-4/ComupterNetworks 17
Enrollment No: 202203103510061

Step-11: Config Static Routes adding network, mask and next hop of Router0.

Step-12: Config Static Routes adding network, mask and next hop of Router1.

UTU/CGPIT/IT/SEM-4/ComupterNetworks 18
Enrollment No: 202203103510061

Step-13: Complete Connection of Static Router.

Results and Conclusion:

UTU/CGPIT/IT/SEM-4/ComupterNetworks 19
Enrollment No: 202203103510061

Practical-5
aim: To perform a practical to create a topology and configure RIP routing protocol.

SoftwareUsed:

1. CiscoPacketTracer(WriteVersion)

2. Windows 7

Description:

Step-1: Tack two PC, two switches and two Router.

Step-2: Connect pc-switch-router with copper straight-through wire, and connection between
two routers with serial DCE wire.

Step-3:

UTU/CGPIT/IT/SEM-4/ComupterNetworks 20
Enrollment No: 202203103510061

Step-4:

Step-5:

UTU/CGPIT/IT/SEM-4/ComupterNetworks 21
Enrollment No: 202203103510061

Step-6:

Step-7:

UTU/CGPIT/IT/SEM-4/ComupterNetworks 22
Enrollment No: 202203103510061

Step-8:

Step-9: Complete Connection of configure RIP routing protocol.

UTU/CGPIT/IT/SEM-4/ComupterNetworks 23
Enrollment No: 202203103510061

UTU/CGPIT/IT/SEM-4/ComupterNetworks 24

You might also like