Instruction

Manual

PUREIT UR5640
125 S Clark St., Ste. 2000
Chicago, IL 60603 USA
Reverse Osmosis Water Purifier
CERTIFICATIONS

For help with installation

visit https://us.pureitwater.com/how-to-install.html for installation video
and https://us.pureitwater.com/support.html for troubleshooting

For any other questions about the product

Our customer excellence team will be happy to assist you
Email: [email protected]
Call: 1-866-4-PUREIT (1-866-478-7348)

M-F 9am-5pm CT

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not cause

PUREIT harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
UR5640 Any Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.

CAUTION:
FOR INDOOR HOUSEHOLD USE ONLY.
RISK OF ELECTRIC SHOCK.
DISCONNECT POWER ADAPTOR BEFORE SERVICING.
ONLY USE THE POWER ADAPTOR PROVIDED WITH THE
APPLIANCE.

ATTENTION:
POUR USAGE DOMESTIQUE SEULEMENT.
DÉBRANCHER DU CIRCUIT D'ALIMENTATION AVANT D'OUVRIR.
5019012 UTILISEZ UNIQUEMENT L’ADAPTATEUR D’ALIMENTATION
FOURNI AVEC L’APPAREIL.
CONTENTS
INSTALLATION INSTRUCTIONS 02
User Information 02
Preparation 02
Parts List 02
Product Introduction 04
Installation Tips 06
Installation Steps 07
Step 1: Install the RO Filter 07
Step 2: Install the Feed Water Adapter 09
Step 3: Install the Pureit Faucet (Non-Air Gap Faucet) 10
Step 4: Install the Drain Saddle 10
Step 5: Connect the Tubing 12
Step 6: Connect the Power Adapter 14
Step 7: Connect the Water Leakage Alarm Indicator 14
Step 8: Starting the System for the First Time 14

OPERATION INSTRUCTIONS 15
User Interface Display 15
Filter Life Reminder 16
Filter Replacement Guide 17
Filter Element Reset 20

TECHNICAL PARAMETERS 21
MAINTENANCE 21
TROUBLE SHOOTING 22
LIMITED PRODUCT WARRANTY 22
WARNING 23
INSTALLATION INSTRUCTIONS

User Information
Thank you for purchasing Pureit reverse osmosis under-the-sink water purifier. Installation and
operating instructions are included in this manual.
• The applicable water temperature range is: 41°F - 100°F (5°C - 38°C). Do not use with water RO

beyond this temperature range.

• Please ensure there is a 100-240 V power outlet with type A plug under the sink prior to
installation. Pureit Faucet Power Adapter Water Leakage Reverse Osmosis
• Never touch the power cord connector when your hands are wet as this may result in electric X 1 Set X 1 Set Alarm Indicator Membrane Filter
shock.
X 1 Set X 1 Set
• Only use original Pureit parts and replacement filters.
• All pictures are for reference only.

Preparation
• Check the parts list to confirm all are included in the package. If there are any parts missing,
cracked or broken, please do not proceed with the installation and contact Pureit by phone
1-866-4-PUREIT (1-866-478-7348) Mon-Fri 9:00 AM - 5:00 PM (CT) or by email at
UR5640
Reverse Osmosis Water Purifier

[email protected]. White 1/4" PE Tubing Instruction Manual Drain Saddle 1/4"

White 3/8" PE Tubing
• Check and ensure there is sufficient space under the sink to install the Pureit device (product
dimensions: 16.14" x 5.51" x 14.17"). The device should be placed inside the cabinet. X 118.11" X 59.06" X1 X 1 Set
• Please ensure you have a 1" hole drilled in the countertop for the Pureit faucet prior to the
installation of the Pureit system.

Parts List Accessories bag

Feed Water Adapter 3/8" Pressure Relief Right Angle Quick

X1 Valve 3/8" Connector 3/8"
PGP
CTO X1 X1

Pureit Water Purifier with CTO & PGP pre-installed

Teflon Tape Lock Clip 1/4" Lock Clip 3/8"
NOTE: X1 X4 X4

Do not install this device in direct sunlight.

Please install this within 59" of the drain pipe.
Installation of this system must comply with state and local laws and regulations.

02 03
INSTALLATION INSTRUCTIONS
Required tools (not provided): Example of connection

Wrench Drill Utility Knife Screw Driver Towel

Product Introduction
The device interface and component parts are listed below. Please familiarize with each
parts for a smooth installation.

Filtered Water Tubing

PGP 1/4" PE Tube
Power Port
RO Filter Life
Indicators
CTO Input Water Port

Waste Water Port

Reset Button

Select Button Filtered Water Port

USB Port
Cold Water Pipe

Pressure Relief Valve

Front View Back View Power Adapter

Input Water Tubing Feed Water

3/8" PE Tube Washer
Adapter

Waste Water Tubing

1/4" PE Tube
Cold Water Supply Valve

Reverse Osmosis
Membrane Filter (RO)

Carbon Block Drain Saddle

Filter (CTO)
PGP CTO RO

Composite
Filter (PGP) Water Leakage
Alarm Indicator

Left Side View (With the RO filter

installed and left panel open)

04 05
INSTALLATION INSTRUCTIONS

Installation Tips How to drill a hole in your sink or countertop

1. Select the desired location for the drinking faucet on the counter top near the sink.
How to use the quick-connect fittings
2. Use a power drill to drill a 1" diameter hole for installation.
To connect to tubing
1. Push the tubing into the fitting around 4/5" until the tubing is fully inserted. NOTE:

NOTE: Depending on the countertop material and sink type, a professional installer is
recommended to drill a hole for the drinking water Pureit faucet installation.
If the tubing is not fully inserted, leakage will occur due to a lack of seal created.

2. When the tubing is fully inserted, put the blue lock clip on the fitting. It will lock the tubing
in place and prevent it from falling off.

NOTE:
Installation Steps
Check and cut the tubing end squarely and cleanly with utility knife to the desired
length. Step 1: Install the RO Filter
1. Locate the recessed handle at the bottom left side of the panel.
2. Pull outward to open the side panel.

Incorrect Cutting Correct Cutting

To disconnect from tubing or plugs

1. Remove the blue block clip from the fitting. Please skip this for plugs.

2. Use your thumb and index finger to press down the lock sleeve. Use your other hand to
pull out the tubing or plugs from the fitting.

3. Take the RO Filter from the package and remove the packaging of the filter.

NOTE:
NOTE: The RO Filter is provided in separate within the same package.
Please do not pull out the tubing or plugs directly. This will damage the fitting and
cause leakage.

06 07
INSTALLATION INSTRUCTIONS

4. Lift the hoop of the new filter to the full extent and keep it in this position. Step 2: Install the Feed Water Adapter
5. Position the bottom of the filter to match a recess in the filter device, then plug the filter tightly
1. Shut off the cold water supply. Turn on the kitchen faucet to release water pressure.
in place.
2. Connect the input water tubing (3/8" PE tubing) to the feed water adapter.

NOTE:
If you find the tubing difficult to connect, please put one end into warm water for 5
seconds to allow it to soften. Then try again.

6. Press down the hoop to the position shown by the dotted line. Tug the filter outward to see
whether it is installed correctly. Unscrew the nut on feed water Thread the PE tube through the Use a wrench to tighten the nut,
adapter, and slide the nut onto nut and cover closely at the make sure it doesn't leak.
the 3/8" PE tube. adapter bulge.

3. Disconnect the cold water pipe from the cold water supply valve.
4. Connect the feed water adapter onto the cold water supply valve (with its washer) and
tighten it with a wrench.

5. Re-connect the cold water pipe onto the feed water adapter and tighten with a wrench.

7. Install back the left panel. Cold Water Pipe

Feed Water
Adapter Washer

Cold Water Supply Valve

08 09
INSTALLATION INSTRUCTIONS

Step 3: Install the Pureit Faucet (Non-Air Gap Faucet) 2. Select the location of the hole and drill a 1/4’’ inch hole through one side of the drain pipe.
Make sure not to penetrate the opposite side of the pipe.
1. Please check if your kitchen sink or countertop has an existing hole. If not, you will need 3. Cut the 1/4" tubing into two. The length should be determined base on how far you plan to
to drill one. Please refer to “How to drill a hole in your sink or countertop” on page 7. place the device from the filtered water tube and waste water tube. Please refer to the tubing
2. Insert the soft rubber pad into the screw of the Pureit faucet. cut note on page 6.

3. Place the Pureit faucet into the countertop hole. Under the sink, put the plastic washer 4. Insert the other 1/4’’ PE tubing as the waste water tubing into the drain saddle. Please push
and fixing nut on the screw and tighten the fixing nut to fasten the Pureit faucet. through 3/5" of the PE tubing into the black sticky pad.

4. Connect the 1/4" tubing to the quick connection fitting on the bottom of the Pureit faucet
and put the 1/4" lock clip on the fitting.

1/4" White Tube

Faucet Spout

Black Sticky Pad

Faucet Body

Soft Rubber Pad

Plastic Washer
Countertop

Fixing Nut
Faucet Stem
5. Place the extruded portion of the waste water tube from the drain saddle into the hole on the
drainage pipe. Then secure the drain saddle by tightening the two screws and hex nuts.

Step 4: Install the Drain Saddle

1. Choose a place on the drainage pipe that is convenient for installing the drain saddle and tubing.

Hex Nuts

6. Tug on the 1/4" tube to check and ensure it is properly secured.

10 11
INSTALLATION INSTRUCTIONS

Step 5: Connect the Tubing 3. Install the filtered water tubing:

Connect the filtered 1/4" water tubing from the Pureit faucet to the filtered water port.
These are the steps to connect the tubing to the Pureit device.

NOTE:
Ensure the tubing is 4/5" inserted into the fitting. Place the blue lock clip into the lock
sleeves to secure the connection.
You can use the 3/8" right angle quick connector to adjust the direction of the tubing.

1. Remove the plugs that are on the Pureit water port at the back of the device:
Please press down the lock sleeves and pull out plugs from the device, which were used to
protect the device from dust and insects, etc. Please refer to “How to use the quick-connect
fittings” on page 6.

Filtered Water Tubing

NOTE: 1/4" PE Tube
To disconnect please remove the lock clip, press down the lock sleeve and pull out
the plugs or inserted tubing.

2. Install the input water tubing:

4. Install the waste water tubing:
Cut the 3/8" tubing into two. The length should be determined base on how far you plan to
Connect the waste 1/4" water tubing from the drain saddle to the waste water port.
place the device from the pressure relief valve connection. Please refer to the tubing cut note
on page 6. Connect the 3/8" tubing from the feed water adapter to the pressure relief valve
(Please note the arrow direction on the valve to ensure the direction of water flow is correct.),
then use the other piece of 3/8" tubing to connect the pressure relief valve to the input water
port.

Pressure Relief Valve

Waste Water Tubing

1/4" PE Tube

Input Water Tubing Feed Water

3/8" PE Tube Adapter
Drain Saddle

5. To ensure all the tubing connections are secured, please check all lock sleeves have the
blue lock clips in place.

12 13
INSTALLATION INSTRUCTIONS OPERATION INSTRUCTIONS

Step 6: Connect the Power Adapter 2. Turn on the Pureit faucet and run the purifier device for 2 hours to flush the system. This
should be done each time when the reverse osmosis filter is changed.
Connect the power adapter into the power port before connecting to the power outlet. 3. Then turn off the Pureit faucet to let the purifier stand for 24 hours.
4. Turn on the Pureit faucet and flush the device for 2 hours again. The system is now ready
Step 7: Connect the Water Leakage Alarm Indicator use and filtered water can be consumed directly.

Connect the water leakage alarm indicator to the USB port and place it in a flat place near NOTE:
the device. Please do not consume water during the flushing process. The water can be reused
and conserved for other purposes such as watering plants.
NOTE:
When the device is running for 30 minutes continuously, a protection mode will kick in
Please place the Pureit logo side upwards and the other probe side downwards.
to stop the device from over-working. A red indicator light will flash repeatedly. Please
A constant beeping will indicate if there is a leakage so please turn off the purifier
turn off the device and then restart it to resume operation.
device immediately and visit https://us.pureitwater.com/support.html for trouble
shooting instructions.

User Interface Display

Power Adapter
Filter life indicator light
PGP • When functioning normally, the filter life indicator light will be blue.
• When the filter life is about to expire, the filter life indicator light will flash red
every 2 seconds.
RO • When a filter has expired, the filter life will flash red quickly every second.
• When the blue lights are flashing in sequence, it indicates that the device is
in flushing mode.
CTO • When the red lights are flashing in sequence, it indicates that the device is
in protection mode. Please turn off the device and restart it, the system will
resume normally.

Step 8: Starting the System for the First Time Reset button
To reset the selected filter, press and hold the reset button for 3 seconds.
1. Plug in the power adapter into a power outlet. Turn on the cold water supply valve, feed
water adapter and the Pureit faucet. Check for leaks.
Select button
NOTE: After replacing the filter, press the select button to reset the new filter. The
Filter life indicators should turn blue at this point. Slight vibrations can be expected as corresponding light indicator will be lit next to the filter name.
the pump starts. PGP = composite filter
Inspect the system for any water leakage especially at the joints, fittings, valves and RO = reverse osmosis membrane filter
tubing connections. If any water leakage is found, turn off the cold water supply CTO = carbon block filter
immediately and reinforce all tubing connections. If the issue persists please contact
Pureit customer service.

14 15
OPERATION INSTRUCTIONS

Filter Life Reminder Filter Replacement Guide

A device sensor monitors and indicates when it is time to replace the filter. 1. Find the correct filter to replace according to the corresponding filter life indicators on the
1. When the filter is about to expire: There will be a beeping sound and the filter's user interface display in front of the device.
corresponding indicator light will flash in red every 2 seconds on the interface.
2. When it is time to replace the filter: The filter's corresponding indicator light will flash in NOTE:
red every second on the interface. Please replace the filter when you see the reminder Always disconnect the appliance from the power outlet and shut off water before
notification. replacing filters.

Filter Life
Indicators

PGP Reverse Osmosis

Membrane Filter (RO)
PGP CTO RO
RO
Carbon Block
Filter (CTO)
PGP CTO RO
CTO
Composite
Filter (PGP)

Composite Filter Carbon Block Filter Reverse Osmosis

Membrane Filter
FUR54PGP FUR54CTO FUR56RO
Filter Life: 6 - 12 Months Filter Life: 6 - 12 Months Filter Life: 2 - 3 Years
2. How to open the device for filter change:
2.1 Locate the recessed handle at the bottom left side of the panel.
NOTE: 2.2 Pull outward to open the side panel.
The recommended filter lifetime is for reference only, the specific replacement cycle
depends on the water source and frequency of use. This reverse osmosis water purifier
contains a replaceable treatment component, critical for the effective reduction of total
dissolved solids and the product water should be tested periodically to verify that the
system is performing properly.

Purchase of replacement filters

Please visit https://us.pureitwater.com for purchase of replacement filters.

16 17
OPERATION INSTRUCTIONS OPERATION INSTRUCTIONS
3. How to remove the filter: 4.4 Press down the hoop to the position shown by the dotted line. Tug the filter outward to see
3.1 Please turn off the inlet valve on feed water adapter or shut off cold water supply valve whether it is installed correctly.
before replacing the filters.
3.2 After turning off the inlet valve, lift the hoop of the expired filter to the full extent and keep
it in this position.
3.3 Pull the hoop outwards and take out the filter, and wipe off the remaining water with a
towel.

4.5 After replacement, please flush the filter according to the system starting method,
normal operation cannot be carried out until the flushing is completed.
4. How to replace the filter:
4.1 Remove the packaging of the new filter.
4.2 Lift the hoop of the new filter to the full extent and keep it in this position.
4.3 Position the bottom of the filter to match a recess in the filter device, then plug the filter
tightly in place.

18 19
OPERATION INSTRUCTIONS TECHNICAL PARAMETERS

Filter Element Reset Product Name Reverse Osmosis Water Purifier

___________________________________________________________________
1. Press the button to select the corresponding filter life indicator light of the replaced Model UR5640
___________________________________________________________________
filter, until the indicator flashes. Applicable Water Source Municipal Tap Water
___________________________________________________________________
Feed Water Pressure 15 PSI ~ 60 PSI
___________________________________________________________________
2. Press the button and hold for 3 seconds until the indicator light turns a steady blue
accompanied by the buzzers. The filter element reset is now completed. Max Working Pressure 100 PSI
___________________________________________________________________
Ambient Temperature 39°F- 100°F (4°C - 38°C)
__________________________________________________________________________________
Ambient Humidity ≤ 90%
___________________________________________________________________
PGP
Applicable Water Temperature 41°F- 100°F (5°C - 38°C)
___________________________________________________________________
Rated Voltage 24 VDC
___________________________________________________________________
RO Rated Power 108 W
___________________________________________________________________
Filtered Water Flow Rate 0.42 Gal/min*
CTO
* 1. The recommended maximum filtered water volume for the Pureit UR5640 is approximately
7000 litres and the flow rate is approximately 0.42 Gal/min of municipal tap water.
Filter Life Indicators Press Press And Hold The appliance has been tested with tap water with below water supply conditions:
• Feed Water Pressure between 15 PSI - 60 PSI
• Water temperature between 72°F - 82°F (22°C - 28°C)
• Total dissolved solids between 0 - 500 ppm
• Water pH 6.5 - 8
• SDI15 < 5
2. All parameters related to the performance of the product are obtained under the above
testing condition and may vary depending on the condition of your tap water supply and
usage environment.

MAINTENANCE
If the system will not be used for more than a week, please shut off the cold water supply valve,
drain the system and disconnect the power.

Please replace filters regularly based on the filter life indicators. The actual filter life depends on
the water source quality and frequency of use.

20 21
TROUBLE SHOOTING WARNING
Having trouble getting your Pureit device to work ? • The device is appropriate for municipal tap water only, and not intended for use of water
Please visit https://us.pureitwater.com/support.html for trouble shooting instructions. that is microbiologically unsafe or of unknown quality.
Should you still have questions, please contact the Pureit Customer Service hotline: • Please do not remove or damage the connector of each parts in the Pureit purification
1-866-4-PUREIT (1-866-478-7348) or e-mail us at [email protected] for additional system.
support. Our operating hours are Mon-Fri 9:00 AM - 5:00 PM (CT).
• Unauthorized modification and disassembly are strictly prohibited and will void the warranty.
• When the device has not been used or left unattended for more than one week, the water
and power supply shall be cut off to better protect the device. It is recommended to drain
the direct drinking water in the first few minutes when reusing, otherwise it may affect the
taste.
• This device is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
• Children should be supervised to ensure that they do not play with the device.
• The feed water pressure is neither lower than 15 PSI nor higher than 60 PSI.
• The reverse osmosis water purifier can operate without air gap faucet. If your local
plumbing code may require one to be installed, use a dual air gap faucet for dishwasher
and reverse osmosis water purifier if necessary.
• Follow below installation instruction that come with the dual air gap faucet.
LIMITED PRODUCT WARRANTY
Warranty information
The Pureit “LIMITED PRODUCT WARRANTY” applies only if the water purifier is installed,
Dual Air Gap Faucet
used, and maintained according to the instructions in this manual. For warranty conditions visit
https://us.pureitwater.com/warranty.html.

Warranty and returns

If you purchased the water purifier at one of our authorized retailers, please contact the
same store to request assistance.

Garbage Disposal

Waste Water Tubing

Reverse Osmosis
Water Purifier

22 23