General Operating Conditions - en
General Operating Conditions - en
The pneumatic components must be supplied with correctly prepared compressed All technical data is correct at the time of going to print.
air free of aggressive media a page 5 onwards. All content, texts, illustrations, images and drawings included in this document
Take the ambient conditions at the place of use into consideration. Corrosive, are the intellectual property of Festo SE & Co. KG and are protected by copyright
abrasive and dusty environments (e.g. water, ozone, grinding dust) will reduce the law.
service life of the product.
Check the resistance of the materials of Festo products to the media used and the Any duplication, processing, translation, microfilming, storage, or processing in
surrounding media a page 24. electronic systems of any kind whatsoever without the consent of
When Festo products are used in safety-oriented applications, all national and in- Festo SE & Co. KG is prohibited.
ternational laws and regulations, for example the Machinery Directive, together
with the relevant references to standards, trade association rules and the applica- All technical data is subject to change according to technical advances.
ble international regulations must be observed and complied with.
Storage conditions
Temperature When repairs are being made to the building technology systems in the ware-
The temperature range in storage areas must be between 10°C and 40°C all year house (welding, grinding etc.), the stored goods should be protected from welding
round. Rapid changes of temperature in the storage area should be avoided. Heat spatter, chips etc.
sources such as heating elements, heating pipes and the like should be shielded
to ensure the stored goods are not directly subject to radiant heat. Adding to/removing from storage
The parts should not be exposed to any extreme fluctuations in temperature.
UV radiation
No direct sunlight (skylights, vent flaps, etc.) and no high-UV artificial lighting. Mechanical effect
Use fluorescent tubes with UV protection. All products, including packs of spare parts/wearing parts for example, should be
stored in such a way that they are not mechanically deformed or damaged, i.e. no
Ambient air buckling or sagging, no point loads. Direct contact between elastomer products
Air circulation and a permanent (proportional) feed of ambient air to the storage and copper or manganese for an extended period should also be avoided be-
room is absolutely essential. You must prevent any media that may affect the ma- cause of possible reciprocal effects.
terials, e.g. solvents and the like arising from production processes, from entering
the storage areas. The storage location should not contain any equipment that Stock management
generates ozone such as indoor air ionisers or high-voltage equipment. To avoid storing parts for long periods of time, the first-in first-out principle should
The relative humidity should not exceed 75%. Condensation must be avoided in be followed. The total storage period should be kept as short as possible. In prin-
all cases. ciple, the specified guarantee periods apply.
Dust
The parts must be stored in suitable containers. The storage room must as far as
possible be free of dust. Attention should be paid in particular to using abra-
sion-resistant, non-porous floor coverings, and ingress of dust particles from ex-
ternal sources (ambient air) should be prevented.
Transport conditions
In principle, there are no restrictions in terms of ambient conditions during land/ ture-controlled transport can be organised. However, this should be agreed con-
sea or air transport, provided the products are sufficiently protected in accord- tractually and as a separate financial matter.
ance with the specifications in the product datasheet by using appropriate prod-
uct and shipping packaging. If necessary, special transport such as tempera-
Pneumatic drives
• Standards-based cylinders to ISO 6432. • Rod clevises to ISO 8140 and DIN 71752.
• Standards-based cylinders to ISO 21287. • Rod eyes to ISO 12240-4, dimension series K.
• Standards-based cylinders to ISO 15552 (ISO 6431, DIN ISO 6431,
VDMA 24562), NFE 49003.1 and UNI 10290.
• Valve terminals for standard valves. • Valve sub-bases with port pattern to ISO 5599-1 and external dimensions to
• Solenoid and pneumatic valves with port pattern to ISO 15407-1. VDMA 24345.
• Valve sub-bases to ISO 15407-1. • Solenoid valves with port pattern to VDI/VDE 3845 (NAMUR).
• Valve terminals with port pattern to ISO 15407-2.
• Solenoid and pneumatic valves with port pattern to ISO 5599-1.
• Valve terminals with port pattern to DIN ISO 5599-2.
Warning symbols are displayed on certain products and packaging from Festo.
These symbols identify products that require specialist expertise to install. These
products must be installed by a professional, as installation is associated with
risks.
IEC 60417-6182: Installation, electrotechnical expertise IEC 60417-6183: Installation, mechanical expertise
To identify electrotechnical equipment and products. The installation of the prod- To identify mechanical equipment and products. The installation of the product
uct with this symbol requires particular electrotechnical expertise. with this symbol requires particular mechanical expertise.
Pressure media
Pressure media for operating pneumatic components from Festo
Compressed air, nitrogen in a gaseous state and noble gases in a gaseous state
can be used as a pressure medium for operating pneumatic components from
Festo.
Please note the following when preparing the pressure media.
Nitrogen (N):
Ambient air comprises approx. 78% nitrogen and 21% oxygen. Nitrogen is an in- Provided the following parameters are adhered to, our products can be operated
ert gas and does not react under normal conditions. with pure nitrogen (100%) as the pressure medium without any restriction to their
service life.
• The nitrogen used must be in a gaseous state
• The operating pressure, operating temperatures and quality (particles, humidi-
ty, oil content) must comply with the values specified for compressed air in the
datasheet
• Flow sensors are calibrated only using the operating medium specified in the
datasheet; operation with other gases will give incorrect results.
Noble gases (helium (He), neon (Ne), argon (Ar), krypton (Kr), xenon (Xe)):
Noble gases are inert and can therefore be used as operating media. Helium, as Provided the following parameters are adhered to, our products can be operated
the lightest of the noble gases, is highly capable of permeating into polymers and with noble gases as the pressure medium without any restriction to their service
elastomers, which can cause gas losses when operating pneumatic components. life.
• The noble gases used must be in a gaseous state
• The operating pressure, operating temperatures and quality (particles, humidi-
ty, oil content) must comply with the values specified for compressed air in the
datasheet
• Flow sensors are calibrated only using the operating medium specified in the
datasheet; operation with other gases will give incorrect results
Carbon dioxide CO2 is a colourless, non-fuel gas, which dissolves easily in water Carbon dioxide can be used as an operating medium without restricting the ser-
to form carbonic acid. It is widely used, e.g. as a drink additive in food technology vice life of our products, provided the following parameters are met:
or as a protective gas in technical applications. • The carbon dioxide must be in a gaseous state.
• The operating pressure, operating temperatures and quality (particles, humidi-
ty, oil content) must comply with the values specified for compressed air in the
datasheet.
• Carbon dioxide must not be used as the operating medium for applications
with an operating pressure > 20 bar.
• Flow sensors are calibrated only using the operating medium specified in the
datasheet; operation with other gases will give incorrect results.
-H- Attention
When using nitrogen, carbon dioxide or noble gases as the operating medium,
it is essential to ensure sufficient ventilation of the affected space (danger of
suffocation if the operating medium escapes).
Pressure media
Water
Festo products are primarily designed for operation with compressed air. If water • Water has a corrosion-stimulating effect.
is specified as an alternative possible operating medium for Festo products, the Particularly in the case of metal fittings, care must be taken to ensure that the
materials that come into contact with the media are in principle compatible with material used for the fittings is electrochemically compatible with the material
water. This does not guarantee a particular longevity of the products. In compari- of the screw-in thread or sealing rings, if appropriate.
son with air, however, water has certain properties that must be taken into ac- • Any leakage can have worse consequences in the case of water than with com-
count in permanent operation. pressed air.
If Festo products are used in cooling or heating circuits, the increased thermal
load can lead to more rapid wear or sticking of seals.
If there were a fault during permanent operation, secondary damage from es-
caping water (e.g. emptying of cooling systems, damage to electrical/electronic
components) should be considered as a possibility.
• Not all water is the same.
The term 'water' used here should be understood to mean liquid mains water
that is free of ice. The suitability of the products for water modified in any way,
such as demineralised water, salt water or water with additives, as well as wa-
ter in the form of vapour, must be enquired about separately.
• The suitability of the products for water – provided nothing is stated to the con-
trary – should not be understood as approval for e.g. drinking water applica-
tions or underfloor heating.
• Water cannot be compressed.
In hydraulic systems, e.g. when switching valves, the lack of compressibility
can lead to pressure peaks. These peaks must not exceed the pressure range
approved for the product.
Particles
Particles in the compressed air usually occur in the form of dust (carbon black,
abraded and corrosion particles). Metal chips (e.g. from conversion work) and res-
idues of sealants such as PFTE tape can also occasionally get into the compressed
air via the compressed air system.
The particles are classified according to ISO 8573-1:2010 as fine dust: size
0.1 ... 5 μm and coarse dust: size > 5 μm.
The maximum water content in air (100% relative air humidity) is dependent on
temperature. Air can only absorb a certain amount of water (in g) per volumetric
unit (in m³), irrespective of pressure. The warmer the air, the more water it can ab-
sorb. Excessive humidity manifests itself as condensation. If the air temperature
drops, for example from 20°C to 3°C, the maximum water content of the com-
pressed air is reduced from 18 g/m³ to 6 g/m³. The compressed air can therefore
only absorb approx. 1/3 as much water as before. The rest (12 g/m3) is precipitat-
ed as drops (dew) and must be drawn off so that it cannot cause any malfunc-
tions.
Water condensation
Water is always present in the air in the form of humidity. When compressed air is
cooled, water is released in large quantities. Drying helps to prevent damage due
to corrosion in compressed air systems and prevents malfunctions in the connect-
ed consuming devices.
Similarly, in the case of compressors that operate without oil, oil aerosols present
in the drawn-in air also lead to a residue of oil pollutants. However, this oil is not
suitable for the lubrication of drives and can even lead to sensitive parts becom-
ing blocked.
The answer is quite simple: compressed air must be so clean that it cannot cause The wide application range of compressed air places many different requirements
any malfunctions or damage. on compressed air quality. If high quality air is required, several filtration stages
As each filter also creates a flow resistance, for economic reasons compressed air are necessary a page 9. If just a single "fine" filter were used, it would
should be only as clean as necessary. quickly become ineffective.
Sizing
The size of the service unit depends on the system's air consumption. Undersizing
-H- Note leads to pressure fluctuations and to reduced filter service life.
Equipment at an air branching/air distribution input should have a high flow For cost reasons, high quality compressed air should only be used where it is ab-
rate as it must meet the total air supply requirement. solutely necessary. Branching modules between the individual filter stages enable
Additional information the user to tap off compressed air of various qualities.
a www.festo.com/catalogue/air preparation
Compressed air filters remove particles and moisture droplets from the air. Parti- The compressed air lubricator provides pneumatic components with adequate lu-
cles > 40 ... 5 μm (depending on the grade of filtration) are retained by a sintered bricant if required. Oil is drawn from a reservoir and atomised when it comes into
filter. Liquids are separated using centrifugal force. The condensate which accu- contact with the air stream. The lubricator is only functional when the air flow is
mulates in the filter bowl must be emptied from time to time, because it would sufficiently strong.
otherwise be drawn in by the air flow.
Various industries often require finely filtered air. That is when fine and micro fil-
ters are used. Fine filters are used for prefiltering down to a particle size of 1 μm.
Micro filters further purify pilot air, removing practically all remaining water and
oil droplets and contamination particles. The degree of compressed air filtration is
99.999% relative to a particle size of 0.01 μm.
The pressure regulator maintains a constant working pressure (secondary side),
regardless of the pressure variations in the system (primary side) and the air con-
sumption. The input pressure must always be greater than working pressure.
The following notes must be observed when lubricated compressed air is used: should only show a pale yellow colouration. If oil droplets appear, this is an in-
• Use Festo special oil OFSW-32 or the alternatives listed in the Festo catalogue dication that too much oil has been used.
(as specified in DIN 51524-HLP 32; viscosity 32 cSt at 40°C). • The colour and condition of the exhaust silencer provide further evidence of
• If lubricated compressed air is used, additional lubrication must not exceed over-lubrication. Marked yellow coloration and dripping oil indicate that the lu-
25 mg/m3 (ISO 8573-1:2010). The quality of compressed air downstream of brication setting is too high.
the compressor must correspond to that of unlubricated compressed air. • Dirty or incorrectly lubricated compressed air will reduce the service life of the
• The lifetime lubrication required for unlubricated operation can be "flushed pneumatic components.
out" when products are operated using lubricated compressed air. This can re- • Service units must be inspected at least twice a week for condensate and cor-
sult in malfunctions if a system is switched back to unlubricated operation af- rect lubrication settings. These inspections should be included in the machine
ter lubricated operation. maintenance plan.
• The lubricators should, where possible, always be installed directly upstream • To protect the environment, as little lubrication as possible should be used.
of the cylinders requiring lubrication in order to prevent operating the entire Festo pneumatic valves and cylinders have been designed so that, under per-
system with lubricated air. mitted operating conditions, additional lubrication is not required and yet a
• Never over-lubricate the system! To determine the correct lubricator settings, long service life is guaranteed.
the following "oil form test" can be implemented: hold a piece of white card ap-
prox. 10 cm away from the exhaust port (without silencer) of a working valve of
the cylinder furthest away. Allow the system to work for some time; the card
Oil content
A differentiation must be made between residual oil for operation with unlubricat- This corresponds to ISO 8573-1:2010 class 4 a www.festo.com/catalogue/air
ed air and additional oil for operation with lubricated air. preparation.
A higher residual oil content is not permitted, regardless of the compressor oil,
Unlubricated operation: because permanent lubrication would otherwise be flushed out over a period
Examinations involving residual oil content have revealed that the various types of of time. This can lead to malfunctions.
oil have entirely different effects. A distinction must therefore be made between
the following oil types when analysing the residual oil content:
• Bio-oils: oils based on synthetic or natural ester (e.g. rapeseed oil methyl es-
ter). In this case, residual oil content must not exceed 0.1 mg/m3.
This corresponds to ISO 8573-1:2010 class 2
a www.festo.com/catalogue/air preparation.
Larger amounts of oil result in damage to O-rings, seals and other component
parts (e.g. filter bowls) of devices in pneumatic systems, and may result in pre-
mature product failure.
• Mineral oils (e.g. HLP oils to DIN 51524, part 2) or similar oils based on polyal-
phaolefins (PAO). In this case, residual oil content must not exceed 5 mg/m3.
Max. pressure dew point 3°C. Permissible particle load max. 10 mg/m³, particle size max. 40 μm.
Corresponds to ISO 8573-1:2010, at least class 4 Corresponds to ISO 8573-1:2010 class 7
a www.festo.com/catalogue/air preparation. a www.festo.com/catalogue/air preparation.
-H- Note
The pressure dew point must be at least 10 K lower than the temperature of the
medium, since ice would otherwise form in the expanded compressed air.
Suitable oils
-H- Note
Special oil in 1 litre containers:
Optimum compressed air preparation means fewer machine failures and greater
Order code: OFSW-32
process reliability. See
Air quality analysis a www.festo.com
1) Air cleaned using universal filters designed for particle sizes of 5 µm (class 6) and 40 µm (class 7) is normally used for the compressed air supply to industrial tools and pneumatic machines. These designs have been used for many
years, before the latest systems for measuring particle sizes were developed, and have enabled satisfactory operation while minimising pressure (and therefore performance) losses.
These filters are not 100% efficient; they offer an efficiency of at least 95% based on the specified particle size, i.e. for class 6, 95% of all particles of size 5 μm are filtered; for class 7, 95% of all particles of size 40 μm are filtered
(measured as per ISO 12500-3).
The class that can be achieved with compressed air preparation depends on the
quality of the compressed air downstream of the compressor. The specifications
apply to typical compressed air systems (this list is not exhaustive).
Central air preparation Air distribu- Decentralised air preparation Typical applications
tion
Component Class Class Component Class3)
Compressor [–:–:–] [–:–:–] Water separator [–:7:4] All applications requiring virtually condensate-free compressed air. No
specific particle filtering.
Compressor [7:4:4]1) [–:4:–]2) Filter [7:4:4] Operating medium for valves, cylinders, secondary packaging (standard)
+ pre-filter 40 μm
+ air dryer
Filter [5:4:3] Applications with a residual oil content < 0.5 mg/m³, textile industry,
5 + 1 μm pneumatic spinning machines, paper industry
Filter [1:4:2] Applications with a residual oil content < 0.01 mg/m³, e.g. air bearings,
5 + 1 + 0.01 μm varnishing, powder coating
Filter [1:4:1] Applications with a residual oil content < 0.003 mg/m³, reduction of oil
5 + 1 + 0.01 μm vapours and odours, optical instruments, sealing air for precision glass
+ activated carbon filter scales/lasers, primary packaging
1) Much higher classes are possible with suitable air preparation downstream of the compressor.
2) Pipe systems can increase the particle content of the compressed air (chips, rust, etc.), liquid oil can concentrate in some sections of the compressed air distribution. Specifications apply at normal room temperature. If parts in the
compressed air system are subject to lower temperatures, the humidity class must be chosen so that the pressure dew point is 10 K below the minimum expected temperature.
3) Class to ISO 8573-1:2010 at room temperature (20°C)
The quality of the compressed air is determined by The air purity class is specified as follows:
• solid contaminants (particles), A = Particles
• humidity and water, and B = Humidity
• oil content C = Oil content
.
Example:
ISO 8573-1:2010 [–:7:–]
Particles: not defined
Humidity: š 0.5 g/m³
Oil content:not defined
Under normal working conditions, pneumatic valves from Festo can be operated • Once the valves have been operated with lubricated compressed air, it is es-
with lubricated or unlubricated compressed air. sential that lubricated compressed air is always used subsequently since the
If any particular product requires a different quality of compressed air, this is indi- oil in the lubricated air will have flushed away the basic lubrication.
cated in the technical data for the relevant product. • In all cases, a degree of filtration is required that removes contaminants up to
Operation with unlubricated compressed air is made possible by the selection of 40 μm (standard filter cartridge version).
the material combination, the shape of the dynamic seals and the basic lubrica- Microfiltration of compressed air may be required for special applications.
tion applied ex works.
Operation with unlubricated compressed air is not possible under the following
working conditions:
Nominal size
The nominal width provides information about the smallest cross section in the This is a measurement that only provides a limited comparison between different
main flow of the valve. It specifies the diameter of the orifice and is expressed in components. To compare products, the standard nominal flow rate must also be
mm. considered.
The standard nominal flow rate qnN is the flow rate characteristic used by Festo Exception 1:
for a device or component expressed in l/min. Silencer
Input pressure p1 = 6 bar
The standard nominal flow rate qnN is the flow rate based on standard conditions Output pressure p2 = pamb
(to DIN 1343) under the following measurement conditions: pamb = atmospheric pressure
• Test medium air
• Temperature 20 ±3°C (temperature of medium) Exception 2:
• Test specimen at ambient temperature Low-pressure components
• The pressures to be set are for components with constant cross section Input pressure p1 = 0.1 bar
(e.g. directional control valves): Output pressure p2 = pamb
Input pressure p1 = 6 bar
Output pressure p2 = 5 bar Exception 3:
For pressure regulators:
Standard conditions to DIN 1343: Input pressure p1 = 10 bar (constant) and output pressure p2 = 6 bar
• tn = 0°C (standard temperature) at q = 0 l/min are set for the test specimen. Subsequently, the flow rate is slowly
• pn = 1.013 bar (standard pressure) and constantly increased using the throttle valve until the output pressure reach-
es a value of p2 = 5 bar. The resulting flow rate is measured.
Force per area. There is a difference between differential pressure with respect to Symbol:
atmosphere and absolute pressure. Pressure specifications for pneumatic devices • Differential pressure with respect to atmosphere p
must normally be assumed to be differential pressure with respect to atmos- • Absolute pressure pabs
phere, unless expressly indicated otherwise. Unit:
• bar
• MPa
• psi
1 bar = 0.1 MPa = 14.5 psi
Data quoted as "max." or "max. permissible" values refer to the maximum safe This is the range between the lowest required and highest permissible operating
pressure at which a component or system can be operated. pressure for safe operation of a component or system. In pneumatics, this pres-
sure range is also referred to as the operating pressure range.
The range between the lowest required and highest permissible pilot pressure for Pressure which, if no longer maintained, causes a monostable directional control
correct operation of a valve or system. valve to return to the normal position by its spring.
The following pressures have been standardised to ISO 4399, for example: 2.5;
6.3; 10; 16; 40 and 100 bar.
Zero pressure occurs in a completely air-free space (100% vacuum). Pressure that Pressure at which a directional control valve is actuated. Catalogue specifications
is calculated from this theoretical zero point is absolute pressure. for response pressure signify that the indicated minimum pressure must be pres-
ent at the signal input to safely switch the valve.
Under normal working conditions, pneumatic drives from Festo can be operated Operation with unlubricated compressed air is not possible under the following
with lubricated or unlubricated dried compressed air. If any particular product re- working conditions:
quires a different quality of compressed air, this is indicated in the technical data Once the drives have been operated with lubricated compressed air, it is essential
for the relevant product. Operation with unlubricated compressed air is made that lubricated compressed air is always used subsequently since the oil in the
possible by the choice of materials used, the material combinations, the shape of lubricated air will have flushed away the basic lubrication.
the dynamic seals and the basic lubrication applied ex works.
Take the ambient conditions at the place of use into consideration. Corrosive, Pneumatic drives are intended to convert pressure energy into motion energy; this
abrasive and dusty environments (e.g. water, ozone, grinding dust) will reduce the process involves the transmission and transfer of forces. "Intended use" does not
service life of the product. include use as a spring or cushioning component, since this would involve addi-
Check the resistance of the materials of Festo products to the media used and tional loads.
surrounding media a page 24.
If pneumatic drives are operated at maximum possible speed, a pause time must In general, drives from Festo can be installed in any position. Any limitations or
be taken into account between the stroke movements. special measures are indicated in the technical data for the relevant product.
Data quoted as "max." or "max. permissible" values refer to the maximum safe This is the range between the lowest required and highest permissible operating
pressure at which a drive or system can be operated. pressure for safe operation of a component or system. In pneumatics, this pres-
sure range is also referred to as the operating pressure range.
Permissible deviation of spring forces in accordance with DIN 2095, quality class Frictional force must be lower than the spring return force. In as far as this is pos-
2, must be taken into consideration for the cylinders' effective force. The effective sible, single-acting cylinders should be operated without lateral forces.
force is also reduced by the value of the frictional forces.
The degree of friction depends on the mounting position and the type of load in-
volved. Lateral forces increase friction.
ISO 15552 (corresponds to the withdrawn standards ISO 6431, DIN ISO 6431,
VDMA 24562, NFE 49003.1, UNI 10290), ISO 6432 and ISO 21287 permit a cer-
tain amount of stroke length deviation from the nominal value due to manufactur-
ing tolerances. These tolerances are always positive. Refer to the table for details
regarding precise permissible deviations.
Standard Piston @ [mm] Stroke length [mm] Permissible stroke deviation [mm]
ISO 6432 8, 10, 12, 16, 20, 25 0 ... 500 +1.5
-H- Note
ISO 15552 32 0 ... 500 +2 In the case of stroke lengths larger
40, 50 500 ... 12500 +3.2 than those shown in the table, the
63 0 ... 500 +2 tolerances must be agreed upon be-
80, 100 500 ... 12500 +4 tween the manufacturer and the
125, 160 0 ... 500 +4 user.
200, 250, 320 500 ... 2000 +5
ISO 21287 20, 25 0 ... 500 +1.5
32, 40, 50 0 ... 500 +2
63, 80, 100 0 ... 500 +2.5
Pneumatic drives from Festo with contactless position sensing are fitted with a
permanent magnet on the cylinder piston, the magnetic field of which is used to
-@-
actuate proximity switches. Proximity switches can be used to detect end or inter-
This symbol is used to indicate piston
mediate positions of cylinders. One or more proximity switches can be clamped
diameter. Piston diameter is represent-
on a cylinder, either directly or using mounting kits.
ed simply by @ in size tables.
Pressure/force table
Piston force [N]
@ Operating pressure [bar]
1 2 3 4 5 6 7 8
2.5 0.4 0.9 1.3 1.8 2.2 2.7 3.1 3.5
3.5 0.9 1.7 3.8 3.5 4.3 5.2 6.1 6.9
5.35 2 4 6.1 8.1 10.1 12.1 14.2 16.2
6 2.5 5.1 7.6 10.2 12.7 15.3 17.8 20.4
8 4.5 9 13.6 18.1 22.6 27.1 31.7 36.2
10 7.1 14.1 21.2 28.3 35.3 42.4 49.5 56.5
12 10.2 20.4 30.5 40.7 50.9 61.0 71.3 81.4
16 18.1 36.5 54.3 72.4 90.5 109 127 145
20 28.3 56.5 84.8 113 141 170 198 226
25 44.2 88.4 133 177 221 265 309 353
32 72.4 145 217 290 362 434 507 579
40 113 226 339 452 565 679 792 905
50 177 353 530 707 884 1060 1240 1410
63 281 561 842 1120 1400 1680 1960 2240
80 452 905 1360 1810 2260 2710 3170 3620
100 707 1410 2120 2830 3530 4240 4950 5650
125 1100 2210 3310 4420 5520 6630 7730 8840
160 1810 3620 5430 7240 9050 10900 12700 14500
200 2830 5650 8480 11300 14100 17000 19800 22600
250 4420 8840 13300 17700 22100 26500 30900 35300
320 7240 14500 21700 29000 36200 43400 50700 57900
The piston force F can be calculated from the piston area A, the operating pres- Software tool ProPneu for sizing can be found on the DVD and at www.festo.com
sure p and the friction R using the following formulae:
Pressure/force graph
Operating pressure p as a function of piston diameter and force F
F [N]
Assuming: The selection of pneumatic drives is determined primarily by the forces to be over-
Load: 800 N come and the distances to be travelled. A small percentage of the piston force is
Available system pressure: 6 bar used to overcome friction, the remainder is used to drive the load.
Only approximate values can be given, since friction force depends on numerous
To be determined: factors (lubrication, operating pressure, back pressure, seal design, etc.). Back
Required piston diameter pressure generates a force which acts in the opposite direction and partially can-
Operating pressure to be set cels out the effective force. It occurs in particular when exhaust air flow controls
are used or the exhaust port is constricted.
Procedure:
From F = 800 N go straight up to where it intersects the 6 bar line. The next larg-
est piston diameter, 50 mm, lies between the lines for 4 and 5 bar, which means
that the operating pressure should be set to approx. 4.5 bar.
Æ [mm]
l [mm]
F [N]
Assuming: Due to buckling stress, the permissible load for a piston rod with a long stroke
Load: 800 N length is lower than the value suggested by the maximum permissible operating
Stroke length: 500 mm pressure and piston area. This load must not exceed certain maximum values.
Piston @ 50 mm These depend on stroke length and piston rod diameter.
To be determined: The graph shows this relationship based on the following formula:
Piston rod diameter 𝜋𝜋 2 ∙ 𝐸𝐸 ∙ 𝐽𝐽
Cylinder type: Standards-based cylinder 𝐹𝐹𝐾𝐾 =
𝑙𝑙2 ∙ 𝑆𝑆
l ~ 2 x stroke
-H- Note
The least satisfactory type of mounting for this kind of stress is a swivel mount-
ing. The permissible load is higher for other types of mounting.
Air consumption
"Air consumption of cylinders" engineering tool
The engineering tool "air consumption of cylinders" determines the air consump- This tool can be found online under Products in the Digital Engineering Tools area.
tion of a cylinder (approximate value), taking into consideration the following pa-
rameters:
• Mode of operation of the cylinder
• Piston @
• Number of cycles
• Stroke length
• Operating pressure
Assuming:
Cylinder: DNC-32-500
Piston @: 32 mm
Piston rod diameter: 12 mm
Stroke length: 500 mm
Operating pressure: 6 bar
Number of cycles per minute: 60 1/min
To be determined:
Air consumption
Results:
Once the parameters have been entered, the following values are returned for the
air consumption:
Per cycle: 5.23 l
Per minute: 314.03 l
𝜋𝜋 Forward stroke:
𝑄𝑄 = ∙ (𝑑𝑑12 − 𝑑𝑑22 ) ∙ ℎ ∙ (𝑝𝑝 + 1) ∙ 10−6
4 𝜋𝜋
𝑄𝑄 = ∙ (32𝑚𝑚𝑚𝑚)2 ∙ 500𝑚𝑚𝑚𝑚 ∙ (6𝑏𝑏𝑏𝑏𝑏𝑏 + 1𝑏𝑏𝑏𝑏𝑏𝑏) ∙ 10−6
4
Q = Air consumption [l] per cm stroke Q = 2.815 l
d1 = Piston diameter [mm]
d2 = Rod diameter [mm] Return stroke:
h = Stroke [mm] 𝜋𝜋
p = Operating pressure, relative [bar] 𝑄𝑄 = ∙ ((32𝑚𝑚𝑚𝑚)2 − (12𝑚𝑚𝑚𝑚)2 ) ∙ 500𝑚𝑚𝑚𝑚 ∙ (6𝑏𝑏𝑏𝑏𝑏𝑏 + 1𝑏𝑏𝑏𝑏𝑏𝑏) ∙ 10−6
4
Q = 2.419 l
Explosive atmospheres are a constant hazard in the chemical and petrochemical Electrical equipment in potentially explosive areas is therefore subject to a special
industries because of the processing techniques used. These explosive atmos- directive, 2014/34/EU. This directive was also extended to non-electrical equip-
pheres are caused by escaping gas, vapours and mist, for example. Explosive at- ment on 1 July 2003.
mospheres can also occur in mills, silos and sugar and feed processing plants be-
cause of the dust/oxygen mixtures there.
ATEX is an acronym of the French expression "Atmosphère explosible". • It applies to the sale of equipment and protective systems within the European
Economic Area.
• Directive 2014/34/EU stipulates the minimum safety requirements for equip- • It relates to both electrical and non-electrical devices, if they have their own
ment and protective systems that are to be operated in explosive atmospheres potential ignition source.
and that have their own ignition sources.
Results: Results:
• Zone classification • Equipment categories
• Temperature classes • Temperature classes
• Explosion groups • Explosion groups
• Ambient temperature • Ambient temperature
Zone Category
Products requiring approval are those Products not requiring approval are
that have their own potential ignition those that do not have their own po-
risk. They are labelled with the CE tential ignition source. These products
marking and the explosion protection can be used in specific explosion
hexagon; operating instructions and zones in compliance with our manufac-
the EU declaration of conformity are turer's instructions:
provided. • Pneumatic accessories
• Tubing
• Fittings
• Pneumatic sub-bases
• Flow control and shut-off valves
• Non-electrical service units
• Mechanical accessories.
The Festo product range for explosion protection includes products for equipment category II
Plug =
not requiring approval, must -H- Note
satisfy certain requirements polyThe permissible technical cata-
logue data for the equipment in
question as well as the warning no-
tices and safety information in the
special documentation provided (in-
cluding operating instructions or, if
applicable, device documentation)
Solenoid coil = must be observed.
According to Directive 2014/34/EU, electrical equipment
both the solenoid coil and the working
valve require approval. At Festo, each
have a separate rating plate so that it
is possible to tell at a glance where the
valve may be used.
EU or EC directives/certifications
EU or EC directives (CE marking)
Festo SE & Co. KG adheres in principle to the applicable regulations. All informa- 3. EU Low Voltage Directive (2014/35/EU), including amendments.
tion is based on the current level of knowledge and is subject to change. We care- Electric and electronic products from Festo designated for use within specific volt-
fully follow any amendments/additions to these regulations and will produce our age limits (50 ... 1000 V AC and 75 ... 1500 V DC) must be labelled with the CE
products accordingly. marking. The corresponding declarations of conformity are available.
This guarantees that products from Festo SE & Co. KG always comply with the re-
quirements that are currently valid. 4. EU Directive on Simple Pressure Vessels (2014/29/EU), including
Most pneumatic products are not subject to any EC directive and are therefore not amendments.
given a CE marking. Products from the sales range of Festo SE & Co. KG that are la- The simple pressure vessels made from non-alloyed steel offered by
belled with the CE marking are currently subject to one or more of the following six Festo SE & Co. KG comply with the requirements of this directive. These air reser-
EU or EC directives in Europe. voirs require CE marking above a certain volume.
These products are labelled with the CE marking. The declaration of conformity is
1. EC Machinery Directive 2006/42/EC, including amendments: available.
2006/42/EC:2007-03-16 and 2009/127/EC:2009-10-21
Pneumatic products from Festo SE & Co. KG are designed in accordance with the 5. EU Directive on Pressure Equipment (2014/68/EU), including amendments.
standard for pneumatic systems ISO 4414 "Pneumatic fluid power – General rules The pressure equipment offered by Festo SE & Co. KG complies with the require-
and safety requirements for systems and their components". Our pneumatic prod- ments of this directive. These pressure vessels require a CE marking above a cer-
ucts do not fall within the scope of application specified in the Machinery tain pressure/volume or pressure/diameter.
Directive. These products are labelled with the CE marking. The declaration of conformity is
They are therefore not labelled with the CE marking in accordance with the Ma- available.
chinery Directive. Exceptions to this are safety devices. As of 29 December 2009, Stainless steel pressure vessels are subject to the Pressure Equipment Directive
incomplete machines also fall under the scope of the Machinery Directive. This in- rather than the Simple Pressure Vessels Directive.
cludes handling systems designed for installation in machines, for example. In-
complete machines are not labelled with the CE marking. A declaration of incorpo- 6. EU Directive on Equipment and Protective Systems for Use in Explosive
ration is enclosed with the machines instead of a declaration of conformity. Atmospheres - ATEX (2014/34/EU).
The products offered by Festo SE & Co. KG which are intended for use in potential-
2. EU Electromagnetic Compatibility Directive (2014/30/EU), including ly explosive atmospheres and which have their own potential ignition risk comply
amendments. with the requirements of this directive. Products that are subject to this directive
The directive must be applied to our electronic and electronic/pneumatic prod- are correspondingly labelled with the CE marking and identified in compliance
ucts. The corresponding products have the CE marking and the corresponding with the directive. The relevant declaration of conformity and the operating in-
declaration of conformity is available. For you, this means a guarantee that this structions are available.
equipment complies with the fundamental requirements in industrial areas. The
use of this equipment in residential areas is restricted if no additional measures
are taken to guarantee compliance with the fundamental requirements of the di-
rective for residential areas!
Solenoid coils are not affected by the EMC Directive.
Product markings
See above UL certification for use in Canada and the USA.
Recognized Product, intended for installation e.g. valve terminal
MPA-S.
To EU Directive 2014/34/EU (ATEX) UL certification for use in Canada and the USA.
Additional marking for equipment and protective systems for use in Listed Product, a ready-to-use device, for example limit switch with
accordance with regulations in a potentially explosive atmosphere cable and plug.
CSA certification for Canada and the USA.
Festo products appear regularly on the winners' podium in major design competi-
tions. There is much more to good design than being "pleasing to the eye". It em-
phasises and symbolises the cutting-edge technology and long-standing value of
Festo products.
PW B S
Paint-wetting
impairment
substances
Paint-wetting impairment substances cause small concave indentations at various In order to restrict or rule out paint-wetting impairment substances depending on
points in the paint layer when surfaces are painted. Silicones, fluoric materials, the area of application, industry experts working in cooperation with the Fraun-
certain oils and greases may contain substances of this kind. Components used in hofer IPA and the Surface Technology department of the VDMA have created appli-
the automotive industry, and especially in painting systems, must not emit cation-specific test criteria. The decisive factor is therefore where a product is
paint-wetting impairment substances to the environment. used and whether it comes into contact with a paint, solvent or surfaces to be
To prevent paint defects caused by paint-wetting impairment substances in pro- painted.
duction, car manufacturers have long been implementing their own test instruc-
tions and standards. The VDMA Specification 24364, a cross-company set of
rules, is available and describes requirements for testing, classification and iden-
tification. Festo supports this initiative with an appropriate classification of its
products.
Definition of zones
Zones define areas of equivalent PWIS relevance in painting operations. The following system of zones can be used to assess the PWIS relevance and thus
the test requirements for products according to their intended use in painting op-
erations.
III Is located within the operational area, but outside the painting production area None
1) Groups of stationary products can generally be allocated to a zone, but this should be reviewed on a case-by-case basis. Mobile products can in principle be used in different zones.
The product group can be selected based on where the product is used and to It establishes the application reference for the PWIS test and thus forms the basis
which zone it has been allocated. for selecting the test category. Product groups S and T cannot be allocated to a
zone.
Zone II
Product group C
Zone I
Product group A and B
B Products with indirect contact with paint or solvent, including compressed air components (e.g. air filters).
C Products that do not come under A and B, including all the control components for the painting process, air ventilation components (e.g. air filters, fire shutters) as
well as other products conveying air.
In future Festo will classify its products according to VDMA 24364 based on their A detailed classification according to VDMA 24364 is provided in the technical
application and intended use. data.
The terminology for designating the extent of electrical protection provided by an • Protection of equipment inside the housing against ingress of solid foreign
enclosure is IP (International Protection) and is defined by IEC/EN 60529 "Degree matter, including dust (foreign matter protection).
of Protection Provided by Enclosures (IP Code)" and DIN 40050 "IP Protection • Protection of electrical equipment against damage that would result if water
Classes" (standard for electrical equipment in road vehicles). These standards de- were to enter the enclosure (protection against water).
scribe the classification of the protection classes provided by enclosures for elec-
trical equipment with rated voltages of up to and including 72.5 kV. They set forth
the following:
• Protection of individuals against contact with live or moving components within
enclosures (protection against accidental contact).
Meaning of digit 2:
Digit 2 refers to the protection of equipment. It rates the degree of protection of
the enclosure with respect to the harmful effects on the equipment if water were
to enter the enclosure.
IP 6 5
Code letters
IP International Protection
In the case of electrical equipment in protection class I, protection against direct Equipment in protection class I includes lights, white goods (washing machines,
contact is ensured by basic insulation. dryers, etc.) and industrial machinery. Symbol:
Protection against indirect contact is provided by prompt disconnection of the
fault voltage. This disconnection is ensured by the contact between the protective
earth conductor and the equipment enclosure via protective earth.
If an insulation fault occurs in the equipment, the fault current flows via the pro-
tective circuit against the earth potential, thereby triggering the upstream fuse
element (e.g. residual current device protection or circuit-breaker).
In the case of equipment in protection class II, the protection refers to direct and Equipment in protection class II includes HiFi components, electric power tools
indirect contact with the improved enclosure insulation. The enclosure insulation and household appliances and is identified with the following symbol:
is reinforced or doubled so that it is not possible to come into contact with contact
voltages outside of the permissible range either in the event of a fault or during
operation.
Equipment in protection class II must not be connected to the protective circuit.
Therefore the equipment does not have a protective contact on the plug.
In the case of equipment in protection class III, protection against direct and indi- Equipment in protection class III is frequently identified (no mandatory identifica-
rect contact is ensured both by a sufficiently high IP degree of protection (protec- tion) with the following symbol:
tion against direct contact with live parts) and by supplying the component with
PELV (protective extra-low voltage) or SELV (safety extra-low voltage) (protection
against indirect contact in the event of a fault).
On the basis of the information currently available, all 24 V DC valve terminals The earth terminal therefore is a functional earthing (discharge of electromagnetic
(e.g. CPV, MPA), position controllers (e.g. SPC), sensors (proximity switches, pres- disturbances) rather than a protective earth function and must always make
sure switches, pressure sensors) and proportional valves from Festo belong to contact.
protection class III.
This means that, in the case of the 24 V DC components from Festo, protection
against direct and indirect contact is ensured by a sufficiently high IP degree of
protection as well as by supplying the component with protective extra-low volt-
age – PELV.
The use of a PELV supply ensures that no contact voltages outside of the permissi-
ble range can occur in the event of a fault due to the high dielectric strength (4 kV)
from the primary to the secondary side.
Due to the increasingly compact designs of modern automation components, pro- It is for this reason that protection class III (no protective earth conductor, as pro-
tection class I is no longer the optimum solution with respect to design size. This tection against electric shock is provided by protective extra-low voltage) is used
is because the standards specify minimum distances for the air and leakage in modern automation components.
paths, which means that further minimising the size of the components is no
longer possible.
What do customers need to know about installing equipment in protection class III?
The electrical supply to the equipment must only be provided by PELV circuits to The earth terminals on the components, where available, are used for deflecting
IEC/EN 60204-1. The general requirements for PELV circuits to IEC/EN 60204-1 electromagnetic disturbances, equipotential bonding and thus ensuring proper
must be taken into account. Power sources are permitted if reliable electrical iso- functioning. They must be connected to the earth potential with low resistance
lation of the operating voltage to IEC/EN 60204-1 is guaranteed. (short cables with large cross section).
Spark arresting
Spark arresting of switch contacts in circuits with solenoid coils
The inductance of solenoid coils stores electromagnetic energy when the circuit is contacts (material creep). Various types of components can be used to avoid these
switched on and this is discharged when switched off. Depending on the switch effects by slowly and constantly discharging the electromagnetic energy.
used, this energy is either converted to a voltage peak (switch-off overvoltage),
which can cause a breakdown in the insulation, or an arc which can burn away the
If the polarity in DC circuits is clearly defined, a simple diode can be used, wired
parallel to the coil. It must be noted that this considerably increases the solenoid
switch-off time.
A more suitable arrangement consists of two zener diodes, wired with opposing
polarity parallel to the coil, which can be used for DC and AC. This prevents
switch-off delays. However, several zener diodes must be wired in series for volt-
ages over 150 V.
Varistors are ideal elements for attenuating the switch-off overvoltage, as their
leakage current only begins to rise when the nominal voltage is exceeded. They
are suitable for DC and AC.
Within DIN VDE 0580, the 100% duty cycle test covers only the electrical part of The worst-case scenario is reviewed in the test. The test constitutes a functional
the solenoid coil. Festo also includes the pneumatic part in this test. test of the solenoid. If the solenoid is also used on valve terminals, the 100%
duty cycle test is performed on the individual device and on equipment in a mani-
fold assembly.
Conditions
• The solenoids are operated with the maximum permissible voltage (continuous • The solenoids are supplied with the maximum permissible operating pressure
operation S1 to DIN VDE 0580). with sealed working ports.
• The solenoids are subjected to the maximum permissible ambient temperature
in a temperature cabinet (non-convecting).
Execution
The solenoids are operated for at least 72 hours under the above conditions. At • Leakage measurements.
the end of this period, the following tests are carried out: • Once the results have been recorded, this process is repeated again until the
• Drop-off current measurement: drop-off behaviour when de-energised. units being tested have reached a total duty cycle of at least 1000 hours or a
• Starting behaviour when immediately energised with the minimum operating termination criterion has been fulfilled.
voltage and with the least favourable pressure ratios for excitation. • Following completion of the 100% duty cycle test, the sealing nipples are in-
spected visually for damage.
Termination criterion
The drop-off behaviour, starting behaviour or leakage exceeds or falls below the
following limit values.
• Drop-off current: > 1.0 mA
• Starting voltage: > UN+10%
• Leakage: > 10 l/h