Approval sheet

SR12, SR10, SR08, SR06, SR04

±1%, ±5%
General purpose chip resistors

Size 1206, 1210, 0805, 0603, 0402

(Anti-Sulfuration )

*Contents in this sheet are subject to change without prior notice.

Page 1 of 9 ASC_SR_V03 Sep.2010

Approval sheet

FEATURE
1. High reliability and stability ±1%
2. Sulfuration resistant 1000ppm
3. Automotive grade AEC Q-200 Compliant
4. 100% CCD inspection
5. RoHS compliant and Lead free products

APPLICATION
• Automotive application
• Consumer electrical equipment
• EDP, Computer application
• Telecom application

DESCRIPTION
The resistors are constructed in a high grade ceramic body (aluminum oxide). Internal metal electrodes are
added at each end and connected by a resistive paste that is applied to the top surface of the substrate. The
extra protective metal film is added onto top side electrodes to protect termination from sulfuration. The
composition of the paste is adjusted to give the approximate resistance required and the value is trimmed to
within tolerance by laser cutting of this resistive layer.
The resistive layer is covered with a protective coat. Finally, the two external end terminations are added. For
ease of soldering the outer layer of these end terminations is a Tin (lead free) alloy.

Fig 1. Construction of a Chip-R

Page 2 of 9 ASC_SR_V03 Sep.2010

Approval sheet

QUICK REFERENCE DATA

Item General Specification
Series No. SR10 SR12 SR08 SR06 SR04

Size code 1210(3225) 1206(3216) 0805(2012) 0603(1608) 0402(1005)

Resistance 1Ω~10MΩ (±5% tolerance), Jumper

Range
1Ω~10MΩ (±1% tolerance)

Resistance ±1% ±5% ±1% ±5% ±1% ±5% ±1% ±5% ±1% ±5%
Tolerance
E96/E24 E24 E96/E24 E24 E96/E24 E24 E96/E24 E24 E96/E24 E24

TCR (ppm/°C)

R > 1MΩ ≤ ± 200 ≤ ± 200 ≤ ± 200 ≤ ± 200 ≤ ± 200

10Ω < R ≦ 1MΩ ≤ ± 100 ≤ ± 100 ≤ ± 100 ≤ ± 100 ≤ ± 100

R ≦ 10Ω -200~+400 -200~+400 -200~+400 -200~+400 -200~+400

Max.
dissipation @ 1/3 W 1/4 W 1/8 W 1/10 W 1/16 W
Tamb=70°C

Max. Operation
Voltage (DC or 200V 200V 150V 75V 50V
RMS)

Max. Overload
Voltage (DC or 400V 400V 300V 150V 100V
RMS)

Climatic
category (IEC 55/155/56
60068)

Note :

1. This is the maximum voltage that may be continuously supplied to the resistor element, see “IEC publication
60115-8”

2. Max. Operation Voltage : So called RCWV (Rated Continuous Working Voltage) is determined by

RCWV = Rated Power × Resistance Value or Max. RCWV listed above, whichever is lower.

3. The resistance of Jumper is defined <0.05Ω.

DIMENSIONS (unit : mm)

SR10 SR12 SR08 SR06 SR04
L 3.10 ± 0.10 3.10 ± 0.10 2.00 ± 0.10 1.60 ± 0.10 1.00 ± 0.05
W 2.60 ± 0.10 1.60 ± 0.10 1.25 ± 0.10 0.80 ± 0.10 0.50 ± 0.05
T 0.55 ± 0.10 0.60 ± 0.15 0.50 ± 0.15 0.45 ± 0.15 0.35 ± 0.05
Tb 0.50 ± 0.20 0.45 ± 0.20 0.40 ± 0.20 0.30 ± 0.15 0.25 ± 0.10
Tt 0.50 ± 0.20 0.50 ± 0.20 0.40 ± 0.20 0.30 ± 0.10 0.20 ± 0.10

Page 3 of 9 ASC_SR_V03 Sep.2010

Approval sheet

MARKING
Size \ Nr. Of digit of code\tolerance ±5% ±1%
1210/1206/0805 3-digits marking 4-digits marking
0603 (1608) 3-digits marking 3-digits marking

0402(1005) N0 MARKING

3-digits marking（±5% : 1210 & 1206 & 0805 & 0603 ）

Each resistor is marked with a three digits code on the protective coating to designate the nominal resistance value.

3-digits marking（±1% : 0603）

Nominal resistance Description
1.E-24 series As 0603 WR06X ±5%.
2.E-96 series The 1st two digit codes are referring to the CODE on the table, the 3rd code is the index of resistance
value :
Y=10-2，X=10-1，A=100，B=101，C=102，D=103，E=104，F=105
EX : 17.8Ω=25X，178Ω=25A，1K78 =25B
17K8=25C， 178K=25D， 1M78=25E
3. Remark There is no marking for the items are not under E-24 and E-96 series
CODE R_value CODE R_value CODE R_Value CODE R_value CODE R_value CODE R_value CODE R_value CODE R_value

01 100 13 133 25 178 37 237 49 316 61 422 73 562 85 750

02 102 14 137 26 182 38 243 50 324 62 432 74 576 86 768

03 105 15 140 27 187 39 249 51 332 63 442 75 590 87 787

04 107 16 143 28 191 40 255 52 340 64 453 76 604 88 806

05 110 17 147 29 196 41 261 53 348 65 464 77 619 89 825

06 113 18 150 30 200 42 267 54 357 66 475 78 634 90 845

07 115 19 154 31 205 43 274 55 365 67 487 79 649 91 866

08 118 20 158 32 210 44 280 56 374 68 499 80 665 92 887

09 121 21 162 33 215 45 287 57 383 69 511 81 681 93 909

10 124 22 165 34 221 46 294 58 392 70 523 82 698 94 931

11 127 23 169 35 226 47 301 59 402 71 536 83 715 95 953

12 130 24 174 36 232 48 309 60 412 72 549 84 732 96 976

4-digits marking（±1% : 1210/1206/0805）

Each resistor is marked with a four digits code on the protective coating to designate the nominal resistance value.

Example
RESISTANCE 10Ω 12Ω 100Ω 6800Ω 47000Ω

（1210/1206/0805/0603 ±5% ）
3-digits marking（ 100 120 101 682 473

4-digits marking 10R0 12R0 1000 6801 4702

Page 4 of 9 ASC_SR_V03 Sep.2010

Approval sheet

FUNCTIONAL DESCRIPTION
Product characterization
Standard values of nominal resistance are taken from the E24 series for resistors with a tolerance of ±5%,
and E96 series for resistors with a tolerance of ±1%. The values of the E24/E96 series are in accordance with
“IEC publication 60063”

Derating
The power that the resistor can dissipate depends on the operating temperature; see Fig.2

Figure 2 Maximum dissipation in percentage of rated power as a

function of the ambient temperature

MOUNTING
Due to their rectangular shapes and small tolerances, Surface Mountable Resistors are suitable for handling by
automatic placement systems.
Chip placement can be on ceramic substrates and printed-circuit boards (PCBs).
Electrical connection to the circuit is by individual soldering condition.
The end terminations guarantee a reliable contact.

Page 5 of 9 ASC_SR_V03 Sep.2010

Approval sheet

SOLDERING CONDITION
The robust construction of chip resistors allows
them to be completely immersed in a solder bath
of 260°C for 10 seconds. Therefore, it is possible
to mount Surface Mount Resistors on one side of
a PCB and other discrete components on the
reverse (mixed PCBs).
Surface Mount Resistors are tested for
solderability at 235°C during 2 seconds. The test
condition for no leaching is 260°C for 30 seconds.
Typical examples of soldering processes that
provide reliable joints without any damage are
given in Fig 3.

Fig 3. Infrared soldering profile for Chip Resistors

CATALOGUE NUMBERS
The resistors have a catalogue number starting with .
SR12 X 472_ J T L
Automotive Type code Resistance code Tolerance Packaging code Termination code
code
X: ±5%, E24: 2 significant digits F : ±1% T : 7” Reeled taping L = Sn base
SR10 : 1210
±5%, 1Ω ~ 10MΩ followed by no. of J : ±5% Q : 10” Reeled taping (lead free)
SR12 : 1206
±1%, 10Ω ~ 1MΩ zeros and a blank P : Jumper G : 13” Reeled taping
SR08 : 0805
W: 220Ω = 221_ B : Bulk
SR06 : 0603
±1%, < 10Ω; >1MΩ (“_” means a blank)
SR04: 0402
±1%, E24+E96: 3 significant
digits followed by no. of
zeros
E24: 102Ω = 1020
E96: 37.4KΩ = 3742

* Anti-Sulfur test conditions: H2S 1000ppm, 25’C, RH 90%, 720hrs, acceptance criteria: +/-1.0%.
SR10, SR12, SR08, SR06:
1. Reeled tape packaging : 8mm width paper taping 5000pcs per 7” reel, 10kpcs per 10” reel, 20kpcs per 13” reel.
2. Bulk packaging : 5000pcs per poly-bag
SR04:
1. Reeled tape packaging : 8mm width paper taping 10,000pcs per reel.
2. Bulk packaging : 10,000pcs per poly-bag

Page 6 of 9 ASC_SR_V03 Sep.2010

 Approval sheet

TEST AND REQUIREMENTS

Essentially all tests are carried out according to the schedule of IEC publication 115-8, category
LCT/UCT/56(rated temperature range : Lower Category Temperature, Upper Category Temperature; damp
heat, long term, 56 days). The testing also meets the requirements specified by EIA, EIAJ and JIS.
The tests are carried out in accordance with IEC publication 68, "Recommended basic climatic and mechanical
robustness testing procedure for electronic components" and under standard atmospheric conditions according
to IEC 60068-1, sub-clause 5.3. Unless otherwise specified, the following value supplied :
Temperature: 15°C to 35°C.
Relative humidity: 45% to 75%.
Air pressure: 86kPa to 106 kPa (860 mbar to 1060 mbar).
All soldering tests are performed with midly activated flux.

REQUIREMENT
TEST PROCEDURE / TEST METHOD
Resistor Ω
0Ω
Electrical Characteristics - DC resistance values measurement Within the specified tolerance
- Temperature Coefficient of Resistance (T.C.R) Refer to “QUICK REFERENCE
JISC5201-1: 1998 Natural resistance change per change in degree centigrade. DATA”
Clause 4.8 R2 − R1
× 106
R1 (t2 − t1 )
(ppm/°C) t1 : 20°C+5°C-1°C

R1 : Resistance at reference temperature

R2 : Resistance at test temperature

Resistance to soldering Un-mounted chips completely immersed for 10±1second in a SAC ∆R/R max. ±(0.5%+0.05Ω)
heat (R.S.H) solder bath at 270℃±5ºC No visible damage
<50mΩ
MIL-STD-202
method 210
a) Bake the sample for 155℃ dwell time 4hrs/ solder dipping 95% coverage min., good tinning
Solderability
235℃/ 5sec.
J-STD-002 b) Steam the sample dwell time 1 hour/ solder dipping 215℃/ 5sec. No visible damage
c) Steam the sample dwell time 1 hour/ solder dipping 260℃/ 7sec.
Temperature cycling 1000 cycles, -55℃ ~ +155℃, dwell time 5~10min ∆R/R max. ±(0.5%+0.05Ω)
JESD22 No visible damage <50mΩ
method JA-104
Moisture Resistance 65±2°C, 80~100% RH, 10 cycles, 24 hours/ cycle ∆R/R max. ±(0.5%+0.05Ω)
MIL-STD-202 No visible damage <50mΩ
method 106
Bias Humidity 1000+48/-0 hours; 85°C, 85% RH, 10% of operation power ∆R/R max. ±(1.0%+0.05Ω)
MIL-STD-202 No visible damage <50mΩ
method 103
Operational Life 1000+48/-0 hours; 35% of operation power, 125±2°C ∆R/R max. ±(1.0%+0.05Ω)
MIL-STD-202 method No visible damage <50mΩ
108

Page 7 of 9 ASC_SR_V03 Sep.2010

 Approval sheet

REQUIREMENT
TEST PROCEDURE / TEST METHOD
Resistor Ω
0Ω
High Temperature 1000+48/-0 hours; without load in a temperature chamber ∆R/R max. ±(1.0%+0.05Ω)
Exposure controlled 155±3°C No visible damage
<50mΩ
MIL-STD-202
method 108
Mechanical Shock 1/2 Sine Pulse / 1500g Peak / Velocity 15.4ft/sec Within the specified
MIL-STD-202 tolerance <50mΩ
method 213 No visible damage
Board Flex Resistors mounted on a 90mm glass epoxy resin PCB(FR4), ∆R/R max.±(1.0%+0.05Ω).
<50mΩ
AEC-Q200-005 bending once 2mm for 10sec No visible damage
Terminal strength Pressurizing force: 1Kg, Test time: 60±1sec. No remarkable damage or removal
AEC-Q200-006 of the terminations
Vibration Test 5g’s for 20min., 12 cycles each of 3 orientations ∆R/R max. ±(1.0%+0.05Ω)
MIL-STD-202 No visible damage <50mΩ
method 204
Thermal shock Test –55 to 155℃/ dwell time 15min/ Max transfer time 20sec ∆R/R max. ±(0.5%+0.05Ω)
MIL-STD-202 300cycles No visible damage <50mΩ
method 107
ESD Test contact 1.0KV (0.5KV for 0402 only) ∆R/R max. ±(1.0%+0.05Ω)
<50mΩ
AEC-Q200-002 No visible damage

TEST CONDITION FOR JUMPER (0 Ω)

Item SR10 SR12 SR08 SR06 SR04
Power Rating At 70°C 1/3W 1/4W 1/8W 1/10W 1/16W
Resistance MAX.50mΩ
Rated Current 2.5A 2A 1.5A 1A 1A
Peak Current 6A 5A 3.5A 3A 2A
Operating Temperature -55 ~ +155°C

Page 8 of 9 ASC_SR_V03 Sep.2010

Approval sheet

PACKAGING
Paper Tape specifications (unit :mm)

Series No. A B W F E
SR10 3.60±0.20 3.00±0.20
SR12 3.60±0.20 2.00±0.20
SR08 2.40±0.20 1.65±0.20 8.00±0.30 3.50±0.20 1.75±0.10

SR06 1.90±0.20 1.10±0.20

SR04 1.20±0.10 0.70±0.10

Series No. P1 P0 ΦD T
SR10/12/08 Max. 1.0
4.00±0.10
SR06 4.00±0.10 Φ1.50 +−00..10 0.65±0.05
SR04 2.00±0.10 0.40±0.05

7” Reel dimensions

Symbol A B C D
(unit : mm) Φ178.0±2.0 Φ60.0±1.0 13.0±0.2 9.0±0.5

Page 9 of 9 ASC_SR_V03 Sep.2010