Scribd
Upload
66 views

Lectric XPchart

The document provides programming and function options for an electric bike controller. It lists 27 programmable parameters including top speed, units, voltage, sleep timer, pedal assist levels, and more. It also lists error codes and options for walking mode, cruise control, lights and changing assist levels while riding.

Uploaded by

dram
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
66 views

Lectric XPchart

The document provides programming and function options for an electric bike controller. It lists 27 programmable parameters including top speed, units, voltage, sleep timer, pedal assist levels, and more. It also lists error codes and options for walking mode, cruise control, lights and changing assist levels while riding.

Uploaded by

dram
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

LECTRIC XP PRGRAMMING AND FUNCTIONS CHART

Options that are in bold are the ones you are most likely to change.
Options in red should not be changed unless advised by authorized rep

Example of Programming Steps Change top speed


1. Access the settings menu by pressing and holding up and down together until the screen says P1
2. Cycle through the programs by pressing the M (mode) button and use up/down to modify the values
3. In this case go to P08 and change the setting from 32 to 45 (km/h)
4. Press and hold up/down together until the main screen is shown
5. Press and hold the M (mode) button to save the new value and exit program mode

Program number / Function Defaults My Settings Extended description


P01: 1-3 Screen brightness 1-3 3 Backlight Brightness Adjustment, 1
Lowest, 3 Brightest.

P02: mph or kph 1 1 Mileage Unit Setting. 0: km, 1:mile

P03: 48V Voltage 48 48 48V Voltage Selection Setting. 24V


36V 48V
P04: Sleep Timer 10 10 Sleep Time. 0: No Sleep, Other
Numbers Are Sleep Time, 1-60
Minutes
P05: PAS levels available 1 1 Power Assist Levels available. 0=0-3,
1=0-5, 2=0-9, 3=0-4, 4=0-6
P06: Tire diameter 20 22.0 Rim Diameter. Mine needed to be set
to 25.5 to correct my odometer

P07: Number of speed magnets 1 1 Number of Speed Magnets. Range: 1-


100
P08: Max speed 32 (km/h) 45 32 or 45 Speed Limit: 0-100km/h.
MAX is 45km/h
P09: Throttle Zero Start 0 0 0: throttle active from standstill 1:
throttle active only when already
moving
P10: Drive Mode 2 2 0=Pedal Assist only, 1=Throttle
only, 2=Both pedal assist and
throttle.
P11: 3 Pedal assist sensitivity 3 2 1-24 PAS sensitivity. Higher
numbers take more rotation to turn
on
P12: 3 3 5 PAS strength 1-5. Higher numbers
cause motor to come on stronger

P13: 12 do not change 12 12 Magnet type 5, 8, 12


P14: 18 do not change 18 18 Current limiting. 1-20 amps
P15: 41.5V low volt protection 41.5 40 The lower limit voltage (where the
motor cuts off)
P16: Zero odometer 6 seconds Odometer zero. Long press the upper
key for 5-6 seconds
P17: Auto cruise 0 0 Maintain steady speed for 6 seconds
to activate
P18: calibrate speedo 100 100 Adjust for rim and tire size
P19: PAS Zero Gear yes/no 0 0 0=no zero gear, 1=has zero gear
P20: comm protocol 0 0 Do not change

P21 Walk Mode Toggle 1 1 0: Walk mode disabled 1:


Walk mode enabled
P22 future use
P23 future use
P24 future use
P25 future use
P26 future use

Options while riding


Walk Mode 3mph Hold down button for 2-3
secconds
Cruise Control Hold down button for 2-3
seccond while throttle is in use

Lights on / off Hold up button for 2-3 seconds to


toggle on / off
Change PAS level Use Up and Down buttons (short
press, one press per level)

Max Speed and Average Speed Press and hold the up arrow and
mode button simultaneously to
toggle between the speedometer,
max speed, and average speed

error codes

002-brake error
003-pas sensor error
004-boosting, 6km/h cruise mode
005-timely cruise mode;
006-low battery level
007-motor error
008-throttle error
009-controller error
010-communication receive error
011-communication sending error
012-EMS communication error
013-frontlight error

You might also like