3/25/24, 11:33 AM Digital Communication - Quick Guide

Digital Communication - Quick Guide

Digital Communication - Analog to Digital

The communication that occurs in our day-to-day life is in the form of signals. These
signals, such as sound signals, generally, are analog in nature. When the
communication needs to be established over a distance, then the analog signals are
sent through wire, using different techniques for effective transmission.

The Necessity of Digitization

The conventional methods of communication used analog signals for long distance
communications, which suffer from many losses such as distortion, interference, and
other losses including security breach.

In order to overcome these problems, the signals are digitized using different
techniques. The digitized signals allow the communication to be more clear and
accurate without losses.

The following figure indicates the difference between analog and digital signals. The
digital signals consist of 1s and 0s which indicate High and Low values respectively.

Advantages of Digital Communication

As the signals are digitized, there are many advantages of digital communication
over analog communication, such as −

The effect of distortion, noise, and interference is much less in digital signals
as they are less affected.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 1/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

Digital circuits are more reliable.

Digital circuits are easy to design and cheaper than analog circuits.
The hardware implementation in digital circuits, is more flexible than analog.
The occurrence of cross-talk is very rare in digital communication.
The signal is un-altered as the pulse needs a high disturbance to alter its
properties, which is very difficult.
Signal processing functions such as encryption and compression are employed
in digital circuits to maintain the secrecy of the information.
The probability of error occurrence is reduced by employing error detecting
and error correcting codes.
Spread spectrum technique is used to avoid signal jamming.
Combining digital signals using Time Division Multiplexing T DM is easier
than combining analog signals using Frequency Division Multiplexing F DM .

The configuring process of digital signals is easier than analog signals.

Digital signals can be saved and retrieved more conveniently than analog
signals.

Many of the digital circuits have almost common encoding techniques and
hence similar devices can be used for a number of purposes.

The capacity of the channel is effectively utilized by digital signals.

Elements of Digital Communication

The elements which form a digital communication system is represented by the
following block diagram for the ease of understanding.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 2/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

Following are the sections of the digital communication system.

Source

The source can be an analog signal. Example: A Sound signal

Input Transducer

This is a transducer which takes a physical input and converts it to an electrical

signal (Example: microphone). This block also consists of an analog to digital
converter where a digital signal is needed for further processes.

A digital signal is generally represented by a binary sequence.

Source Encoder

The source encoder compresses the data into minimum number of bits. This process
helps in effective utilization of the bandwidth. It removes the redundant bits
unnecessaryexcessbits, i. e. , zeroes .

Channel Encoder

The channel encoder, does the coding for error correction. During the transmission of
the signal, due to the noise in the channel, the signal may get altered and hence to
avoid this, the channel encoder adds some redundant bits to the transmitted data.
These are the error correcting bits.

Digital Modulator

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 3/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

The signal to be transmitted is modulated here by a carrier. The signal is also

converted to analog from the digital sequence, in order to make it travel through the
channel or medium.

Channel

The channel or a medium, allows the analog signal to transmit from the transmitter
end to the receiver end.

Digital Demodulator

This is the first step at the receiver end. The received signal is demodulated as well
as converted again from analog to digital. The signal gets reconstructed here.

Channel Decoder

The channel decoder, after detecting the sequence, does some error corrections. The
distortions which might occur during the transmission, are corrected by adding some
redundant bits. This addition of bits helps in the complete recovery of the original
signal.

Source Decoder

The resultant signal is once again digitized by sampling and quantizing so that the
pure digital output is obtained without the loss of information. The source decoder
recreates the source output.

Output Transducer

This is the last block which converts the signal into the original physical form, which
was at the input of the transmitter. It converts the electrical signal into physical
output (Example: loud speaker).

Output Signal

This is the output which is produced after the whole process. Example − The sound
signal received.

This unit has dealt with the introduction, the digitization of signals, the advantages
and the elements of digital communications. In the coming chapters, we will learn
about the concepts of Digital communications, in detail.

Pulse Code Modulation

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 4/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

Modulation is the process of varying one or more parameters of a carrier signal in

accordance with the instantaneous values of the message signal.

The message signal is the signal which is being transmitted for communication and
the carrier signal is a high frequency signal which has no data, but is used for long
distance transmission.

There are many modulation techniques, which are classified according to the type of
modulation employed. Of them all, the digital modulation technique used is Pulse
Code Modulation P CM .

A signal is pulse code modulated to convert its analog information into a binary
sequence, i.e., 1s and 0s. The output of a PCM will resemble a binary sequence. The
following figure shows an example of PCM output with respect to instantaneous
values of a given sine wave.

Instead of a pulse train, PCM produces a series of numbers or digits, and hence this
process is called as digital. Each one of these digits, though in binary code,
represent the approximate amplitude of the signal sample at that instant.

In Pulse Code Modulation, the message signal is represented by a sequence of coded

pulses. This message signal is achieved by representing the signal in discrete form in
both time and amplitude.

Basic Elements of PCM

The transmitter section of a Pulse Code Modulator circuit consists of Sampling,
Quantizing and Encoding, which are performed in the analog-to-digital converter
section. The low pass filter prior to sampling prevents aliasing of the message signal.

The basic operations in the receiver section are regeneration of impaired signals,
decoding, and reconstruction of the quantized pulse train. Following is the block

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 5/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

diagram of PCM which represents the basic elements of both the transmitter and the
receiver sections.

Low Pass Filter

This filter eliminates the high frequency components present in the input analog
signal which is greater than the highest frequency of the message signal, to avoid
aliasing of the message signal.

Sampler

This is the technique which helps to collect the sample data at instantaneous values
of message signal, so as to reconstruct the original signal. The sampling rate must
be greater than twice the highest frequency component W of the message signal, in
accordance with the sampling theorem.

Quantizer

Quantizing is a process of reducing the excessive bits and confining the data. The
sampled output when given to Quantizer, reduces the redundant bits and compresses
the value.

Encoder

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 6/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

The digitization of analog signal is done by the encoder. It designates each quantized
level by a binary code. The sampling done here is the sample-and-hold process.
These three sections LP F , S ampler, andQuantizer will act as an analog to digital
converter. Encoding minimizes the bandwidth used.

Regenerative Repeater

This section increases the signal strength. The output of the channel also has one
regenerative repeater circuit, to compensate the signal loss and reconstruct the
signal, and also to increase its strength.

Decoder

The decoder circuit decodes the pulse coded waveform to reproduce the original
signal. This circuit acts as the demodulator.

Reconstruction Filter

After the digital-to-analog conversion is done by the regenerative circuit and the
decoder, a low-pass filter is employed, called as the reconstruction filter to get back
the original signal.

Hence, the Pulse Code Modulator circuit digitizes the given analog signal, codes it
and samples it, and then transmits it in an analog form. This whole process is
repeated in a reverse pattern to obtain the original signal.

Digital Communication - Sampling

Sampling is defined as, “The process of measuring the instantaneous values of
continuous-time signal in a discrete form.”

Sample is a piece of data taken from the whole data which is continuous in the time
domain.

When a source generates an analog signal and if that has to be digitized, having 1s
and 0s i.e., High or Low, the signal has to be discretized in time. This discretization
of analog signal is called as Sampling.

The following figure indicates a continuous-time signal x and a sampled signal xs t.

t

When x t is multiplied by a periodic impulse train, the sampled signal xs t is

obtained.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 7/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

Sampling Rate
To discretize the signals, the gap between the samples should be fixed. That gap can
be termed as a sampling period Ts.

1
S ampling F requency = = fs
Ts

Where,

Ts is the sampling time

fs is the sampling frequency or the sampling rate

Sampling frequency is the reciprocal of the sampling period. This sampling

frequency, can be simply called as Sampling rate. The sampling rate denotes the
number of samples taken per second, or for a finite set of values.

For an analog signal to be reconstructed from the digitized signal, the sampling rate
should be highly considered. The rate of sampling should be such that the data in
the message signal should neither be lost nor it should get over-lapped. Hence, a
rate was fixed for this, called as Nyquist rate.

Nyquist Rate

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 8/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

Suppose that a signal is band-limited with no frequency components higher than W

Hertz. That means, W is the highest frequency. For such a signal, for effective
reproduction of the original signal, the sampling rate should be twice the highest
frequency.

Which means,

fS = 2W

Where,

fS is the sampling rate

W is the highest frequency

This rate of sampling is called as Nyquist rate.

A theorem called, Sampling Theorem, was stated on the theory of this Nyquist rate.

Sampling Theorem
The sampling theorem, which is also called as Nyquist theorem, delivers the theory
of sufficient sample rate in terms of bandwidth for the class of functions that are
bandlimited.

The sampling theorem states that, “a signal can be exactly reproduced if it is

sampled at the rate fs which is greater than twice the maximum frequency W.”

To understand this sampling theorem, let us consider a band-limited signal, i.e., a

signal whose value is non-zero between some –W and W Hertz.

Such a signal is represented as x(f ) = 0 f or ∣ f ∣> W

For the continuous-time signal x t, the band-limited signal in frequency domain, can
be represented as shown in the following figure.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 9/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

We need a sampling frequency, a frequency at which there should be no loss of

information, even after sampling. For this, we have the Nyquist rate that the
sampling frequency should be two times the maximum frequency. It is the critical
rate of sampling.

If the signal xt is sampled above the Nyquist rate, the original signal can be
recovered, and if it is sampled below the Nyquist rate, the signal cannot be
recovered.

The following figure explains a signal, if sampled at a higher rate than 2w in the
frequency domain.

The above figure shows the Fourier transform of a signal xs t. Here, the information
is reproduced without any loss. There is no mixing up and hence recovery is

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 10/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

possible.

The Fourier Transform of the signal xs t is

∞
1
X s (w) = ∑ X(w − nw0 )
Ts
n=−∞

Where Ts = Sampling Period and w0 =

2π

Ts

Let us see what happens if the sampling rate is equal to twice the highest frequency
(2W)

That means,

fs = 2W

Where,

fs is the sampling frequency

W is the highest frequency

The result will be as shown in the above figure. The information is replaced without
any loss. Hence, this is also a good sampling rate.

Now, let us look at the condition,

fs < 2W

The resultant pattern will look like the following figure.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 11/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

We can observe from the above pattern that the over-lapping of information is done,
which leads to mixing up and loss of information. This unwanted phenomenon of
over-lapping is called as Aliasing.

Aliasing
Aliasing can be referred to as “the phenomenon of a high-frequency component in
the spectrum of a signal, taking on the identity of a low-frequency component in the
spectrum of its sampled version.”

The corrective measures taken to reduce the effect of Aliasing are −

In the transmitter section of PCM, a low pass anti-aliasing filter is

employed, before the sampler, to eliminate the high frequency components,
which are unwanted.
The signal which is sampled after filtering, is sampled at a rate slightly higher
than the Nyquist rate.

This choice of having the sampling rate higher than Nyquist rate, also helps in the
easier design of the reconstruction filter at the receiver.

Scope of Fourier Transform

It is generally observed that, we seek the help of Fourier series and Fourier
transforms in analyzing the signals and also in proving theorems. It is because −

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 12/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

The Fourier Transform is the extension of Fourier series for non-periodic

signals.
Fourier transform is a powerful mathematical tool which helps to view the
signals in different domains and helps to analyze the signals easily.

Any signal can be decomposed in terms of sum of sines and cosines using this
Fourier transform.

In the next chapter, let us discuss about the concept of Quantization.

Digital Communication - Quantization

The digitization of analog signals involves the rounding off of the values which are
approximately equal to the analog values. The method of sampling chooses a few
points on the analog signal and then these points are joined to round off the value to
a near stabilized value. Such a process is called as Quantization.

Quantizing an Analog Signal

The analog-to-digital converters perform this type of function to create a series of
digital values out of the given analog signal. The following figure represents an
analog signal. This signal to get converted into digital, has to undergo sampling and
quantizing.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 13/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

The quantizing of an analog signal is done by discretizing the signal with a number of
quantization levels. Quantization is representing the sampled values of the
amplitude by a finite set of levels, which means converting a continuous-amplitude
sample into a discrete-time signal.

The following figure shows how an analog signal gets quantized. The blue line
represents analog signal while the brown one represents the quantized signal.

Both sampling and quantization result in the loss of information. The quality of a
Quantizer output depends upon the number of quantization levels used. The discrete
amplitudes of the quantized output are called as representation levels or
reconstruction levels. The spacing between the two adjacent representation levels
is called a quantum or step-size.

The following figure shows the resultant quantized signal which is the digital form for
the given analog signal.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 14/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

This is also called as Stair-case waveform, in accordance with its shape.

Types of Quantization
There are two types of Quantization - Uniform Quantization and Non-uniform
Quantization.

The type of quantization in which the quantization levels are uniformly spaced is
termed as a Uniform Quantization. The type of quantization in which the
quantization levels are unequal and mostly the relation between them is logarithmic,
is termed as a Non-uniform Quantization.

There are two types of uniform quantization. They are Mid-Rise type and Mid-Tread
type. The following figures represent the two types of uniform quantization.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 15/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

Figure 1 shows the mid-rise type and figure 2 shows the mid-tread type of uniform
quantization.

The Mid-Rise type is so called because the origin lies in the middle of a
raising part of the stair-case like graph. The quantization levels in this type
are even in number.
The Mid-tread type is so called because the origin lies in the middle of a
tread of the stair-case like graph. The quantization levels in this type are odd
in number.

Both the mid-rise and mid-tread type of uniform quantizers are symmetric
about the origin.

Quantization Error
For any system, during its functioning, there is always a difference in the values of
its input and output. The processing of the system results in an error, which is the
difference of those values.

The difference between an input value and its quantized value is called a
Quantization Error. A Quantizer is a logarithmic function that performs
Quantization roundingof f thevalue. An analog-to-digital converter (ADC) works as
a quantizer.

The following figure illustrates an example for a quantization error, indicating the
difference between the original signal and the quantized signal.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 16/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

Quantization Noise

It is a type of quantization error, which usually occurs in analog audio signal, while
quantizing it to digital. For example, in music, the signals keep changing
continuously, where a regularity is not found in errors. Such errors create a
wideband noise called as Quantization Noise.

Companding in PCM
The word Companding is a combination of Compressing and Expanding, which
means that it does both. This is a non-linear technique used in PCM which
compresses the data at the transmitter and expands the same data at the receiver.
The effects of noise and crosstalk are reduced by using this technique.

There are two types of Companding techniques. They are −

A-law Companding Technique

Uniform quantization is achieved at A = 1, where the characteristic curve is

linear and no compression is done.
A-law has mid-rise at the origin. Hence, it contains a non-zero value.
A-law companding is used for PCM telephone systems.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 17/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

µ-law Companding Technique

Uniform quantization is achieved at µ = 0, where the characteristic curve is

linear and no compression is done.
µ-law has mid-tread at the origin. Hence, it contains a zero value.
µ-law companding is used for speech and music signals.

µ-law is used in North America and Japan.

Digital Communication - Differential PCM

For the samples that are highly correlated, when encoded by PCM technique, leave
redundant information behind. To process this redundant information and to have a
better output, it is a wise decision to take a predicted sampled value, assumed from
its previous output and summarize them with the quantized values. Such a process
is called as Differential PCM DP C M technique.

DPCM Transmitter
The DPCM Transmitter consists of Quantizer and Predictor with two summer circuits.
Following is the block diagram of DPCM transmitter.

The signals at each point are named as −

x(nTs ) is the sampled input

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 18/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

x̂ (nTs ) is the predicted sample

e(nTs ) is the difference of sampled input and predicted output, often called
as prediction error
v(nTs ) is the quantized output
u(nTs ) is the predictor input which is actually the summer output of the
predictor output and the quantizer output

The predictor produces the assumed samples from the previous outputs of the
transmitter circuit. The input to this predictor is the quantized versions of the input
signal x(nTs ).

Quantizer Output is represented as −

v(nTs ) = Q[e(nTs )]

= e(nTs ) + q(nTs )

Where q (nTs) is the quantization error

Predictor input is the sum of quantizer output and predictor output,

u(nTs ) = x̂ (nTs ) + v(nTs )

u(nTs ) = x̂ (nTs ) + e(nTs ) + q(nTs )

u(nTs ) = x(nTs ) + q(nTs )

The same predictor circuit is used in the decoder to reconstruct the original input.

DPCM Receiver
The block diagram of DPCM Receiver consists of a decoder, a predictor, and a
summer circuit. Following is the diagram of DPCM Receiver.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 19/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

The notation of the signals is the same as the previous ones. In the absence of
noise, the encoded receiver input will be the same as the encoded transmitter
output.

As mentioned before, the predictor assumes a value, based on the previous outputs.
The input given to the decoder is processed and that output is summed up with the
output of the predictor, to obtain a better output.

Digital Communication - Delta Modulation

The sampling rate of a signal should be higher than the Nyquist rate, to achieve
better sampling. If this sampling interval in Differential PCM is reduced considerably,
the sampleto-sample amplitude difference is very small, as if the difference is 1-bit
quantization, then the step-size will be very small i.e., Δ delta .

Delta Modulation
The type of modulation, where the sampling rate is much higher and in which the
stepsize after quantization is of a smaller value Δ, such a modulation is termed as
delta modulation.

Features of Delta Modulation

Following are some of the features of delta modulation.

An over-sampled input is taken to make full use of the signal correlation.

The quantization design is simple.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 20/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

The input sequence is much higher than the Nyquist rate.

The quality is moderate.
The design of the modulator and the demodulator is simple.
The stair-case approximation of output waveform.
The step-size is very small, i.e., Δ delta .

The bit rate can be decided by the user.

This involves simpler implementation.

Delta Modulation is a simplified form of DPCM technique, also viewed as 1-bit DPCM
scheme. As the sampling interval is reduced, the signal correlation will be higher.

Delta Modulator
The Delta Modulator comprises of a 1-bit quantizer and a delay circuit along with two
summer circuits. Following is the block diagram of a delta modulator.

The predictor circuit in DPCM is replaced by a simple delay circuit in DM.

From the above diagram, we have the notations as −

x(nTs ) = over sampled input

ep (nTs ) = summer output and quantizer input

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 21/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

eq (nTs ) = quantizer output = v(nTs )

x̂ (nTs ) = output of delay circuit

u(nTs ) = input of delay circuit

Using these notations, now we shall try to figure out the process of delta modulation.

ep (nTs ) = x(nTs ) − x̂ (nTs )

---------equation 1

= x(nTs ) − u([n − 1]Ts )

= x(nTs ) − [x̂ [[n − 1]Ts ] + v[[n − 1]Ts ]]

---------equation 2

Further,

v(nTs ) = eq (nTs ) = S . sig. [ep (nTs )]

---------equation 3

u(nTs ) = x̂ (nTs ) + eq (nTs )

Where,

x̂ (nTs ) = the previous value of the delay circuit

eq (nTs ) = quantizer output = v(nTs )

Hence,

u(nTs ) = u([n − 1]Ts ) + v(nTs )

---------equation 4

Which means,

The present input of the delay unit

= T hepreviousoutputof thedelayunit + thepresentquantizeroutput

Assuming zero condition of Accumulation,

n

u(nTs ) = S ∑ sig[ep (jTs )]

j=1

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 22/75
3/25/24, 11:33 AM Digital Communication - Quick Guide
n

Accumulated version of DM output = ∑ v(jTs )

j=1

---------equation 5

Now, note that

x̂ (nTs ) = u([n − 1]Ts )

n−1

= ∑ v(jTs )

j=1

---------equation 6

Delay unit output is an Accumulator output lagging by one sample.

From equations 5 & 6, we get a possible structure for the demodulator.

A Stair-case approximated waveform will be the output of the delta modulator with
the step-size as delta (Δ). The output quality of the waveform is moderate.

Delta Demodulator
The delta demodulator comprises of a low pass filter, a summer, and a delay circuit.
The predictor circuit is eliminated here and hence no assumed input is given to the
demodulator.

Following is the diagram for delta demodulator.

From the above diagram, we have the notations as −

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 23/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

v̂ (nTs ) is the input sample

û (nTs ) is the summer output

x̄ (nTs ) is the delayed output

A binary sequence will be given as an input to the demodulator. The stair-case

approximated output is given to the LPF.

Low pass filter is used for many reasons, but the prominent reason is noise
elimination for out-of-band signals. The step-size error that may occur at the
transmitter is called granular noise, which is eliminated here. If there is no noise
present, then the modulator output equals the demodulator input.

Advantages of DM Over DPCM

1-bit quantizer
Very easy design of the modulator and the demodulator

However, there exists some noise in DM.

Slope Over load distortion (when Δ is small)

Granular noise (when Δ is large)

Adaptive Delta Modulation ADM

In digital modulation, we have come across certain problem of determining the step-
size, which influences the quality of the output wave.

A larger step-size is needed in the steep slope of modulating signal and a smaller
stepsize is needed where the message has a small slope. The minute details get
missed in the process. So, it would be better if we can control the adjustment of
step-size, according to our requirement in order to obtain the sampling in a desired
fashion. This is the concept of Adaptive Delta Modulation.

Following is the block diagram of Adaptive delta modulator.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 24/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

The gain of the voltage controlled amplifier is adjusted by the output signal from the
sampler. The amplifier gain determines the step-size and both are proportional.

ADM quantizes the difference between the value of the current sample and the
predicted value of the next sample. It uses a variable step height to predict the next
values, for the faithful reproduction of the fast varying values.

Digital Communication - Techniques

There are a few techniques which have paved the basic path to digital
communication processes. For the signals to get digitized, we have the sampling and
quantizing techniques.

For them to be represented mathematically, we have LPC and digital multiplexing

techniques. These digital modulation techniques are further discussed.

Linear Predictive Coding

Linear Predictive Coding LP C is a tool which represents digital speech signals in
linear predictive model. This is mostly used in audio signal processing, speech
synthesis, speech recognition, etc.

Linear prediction is based on the idea that the current sample is based on the linear
combination of past samples. The analysis estimates the values of a discrete-time
signal as a linear function of the previous samples.

The spectral envelope is represented in a compressed form, using the information of

the linear predictive model. This can be mathematically represented as −

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 25/75
3/25/24, 11:33 AM Digital Communication - Quick Guide
p

s(n) = ∑ αk s(n − k) for some value of p and αk

k=1

Where

sn is the current speech sample

k is a particular sample
p is the most recent value
αk is the predictor co-efficient

sn − k is the previous speech sample

For LPC, the predictor co-efficient values are determined by minimizing the sum of
squared differences overaf initeinterval between the actual speech samples and
the linearly predicted ones.

This is a very useful method for encoding speech at a low bit rate. The LPC method
is very close to the Fast Fourier Transform F F T method.

Multiplexing
Multiplexing is the process of combining multiple signals into one signal, over a
shared medium. These signals, if analog in nature, the process is called as analog
multiplexing. If digital signals are multiplexed, it is called as digital multiplexing.

Multiplexing was first developed in telephony. A number of signals were combined to

send through a single cable. The process of multiplexing divides a communication
channel into several number of logical channels, allotting each one for a different
message signal or a data stream to be transferred. The device that does
multiplexing, can be called as a MUX. The reverse process, i.e., extracting the
number of channels from one, which is done at the receiver is called as de-
multiplexing. The device which does de-multiplexing is called as DEMUX.

The following figures represent MUX and DEMUX. Their primary use is in the field of
communications.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 26/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

Types of Multiplexers
There are mainly two types of multiplexers, namely analog and digital. They are
further divided into FDM, WDM, and TDM. The following figure gives a detailed idea
on this classification.

Actually, there are many types of multiplexing techniques. Of them all, we have the
main types with general classification, mentioned in the above figure.

Analog Multiplexing

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 27/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

The analog multiplexing techniques involve signals which are analog in nature. The
analog signals are multiplexed according to their frequency F DM or wavelength
W DM .

Frequency Division Multiplexing F DM

In analog multiplexing, the most used technique is Frequency Division

Multiplexing F DM . This technique uses various frequencies to combine streams of
data, for sending them on a communication medium, as a single signal.

Example − A traditional television transmitter, which sends a number of channels

through a single cable, uses FDM.

Wavelength Division Multiplexing W DM

Wavelength Division multiplexing is an analog technique, in which many data

streams of different wavelengths are transmitted in the light spectrum. If the
wavelength increases, the frequency of the signal decreases. A prism which can turn
different wavelengths into a single line, can be used at the output of MUX and input
of DEMUX.

Example − Optical fiber communications use WDM technique to merge different

wavelengths into a single light for communication.

Digital Multiplexing
The term digital represents the discrete bits of information. Hence, the available data
is in the form of frames or packets, which are discrete.

Time Division Multiplexing T DM

In TDM, the time frame is divided into slots. This technique is used to transmit a
signal over a single communication channel, by allotting one slot for each message.

Of all the types of TDM, the main ones are Synchronous and Asynchronous TDM.

Synchronous TDM

In Synchronous TDM, the input is connected to a frame. If there are ‘n’ number of
connections, then the frame is divided into ‘n’ time slots. One slot is allocated for
each input line.

In this technique, the sampling rate is common to all signals and hence the same
clock input is given. The MUX allocates the same slot to each device at all times.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 28/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

Asynchronous TDM

In Asynchronous TDM, the sampling rate is different for each of the signals and a
common clock is not required. If the allotted device, for a time-slot, transmits
nothing and sits idle, then that slot is allotted to another device, unlike synchronous.
This type of TDM is used in Asynchronous transfer mode networks.

Regenerative Repeater
For any communication system to be reliable, it should transmit and receive the
signals effectively, without any loss. A PCM wave, after transmitting through a
channel, gets distorted due to the noise introduced by the channel.

The regenerative pulse compared with the original and received pulse, will be as
shown in the following figure.

For a better reproduction of the signal, a circuit called as regenerative repeater is

employed in the path before the receiver. This helps in restoring the signals from the
losses occurred. Following is the diagrammatical representation.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 29/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

This consists of an equalizer along with an amplifier, a timing circuit, and a decision
making device. Their working of each of the components is detailed as follows.

Equalizer

The channel produces amplitude and phase distortions to the signals. This is due to
the transmission characteristics of the channel. The Equalizer circuit compensates
these losses by shaping the received pulses.

Timing Circuit

To obtain a quality output, the sampling of the pulses should be done where the
signal to noise ratio S N R is maximum. To achieve this perfect sampling, a periodic
pulse train has to be derived from the received pulses, which is done by the timing
circuit.

Hence, the timing circuit, allots the timing interval for sampling at high SNR, through
the received pulses.

Decision Device

The timing circuit determines the sampling times. The decision device is enabled at
these sampling times. The decision device decides its output based on whether the
amplitude of the quantized pulse and the noise, exceeds a pre-determined value or
not.

These are few of the techniques used in digital communications. There are other
important techniques to be learned, called as data encoding techniques. Let us learn
about them in the subsequent chapters, after taking a look at the line codes.

Digital Communication - Line Codes

A line code is the code used for data transmission of a digital signal over a
transmission line. This process of coding is chosen so as to avoid overlap and
distortion of signal such as inter-symbol interference.

Properties of Line Coding

Following are the properties of line coding −

As the coding is done to make more bits transmit on a single signal, the
bandwidth used is much reduced.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 30/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

For a given bandwidth, the power is efficiently used.

The probability of error is much reduced.
Error detection is done and the bipolar too has a correction capability.
Power density is much favorable.
The timing content is adequate.
Long strings of 1s and 0s is avoided to maintain transparency.

Types of Line Coding

There are 3 types of Line Coding

Unipolar
Polar
Bi-polar

Unipolar Signaling
Unipolar signaling is also called as On-Off Keying or simply OOK.

The presence of pulse represents a 1 and the absence of pulse represents a 0.

There are two variations in Unipolar signaling −

Non Return to Zero N RZ

Return to Zero RZ

Unipolar Non-Return to Zero N RZ

In this type of unipolar signaling, a High in data is represented by a positive pulse

called as Mark, which has a duration T0 equal to the symbol bit duration. A Low in
data input has no pulse.

The following figure clearly depicts this.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 31/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

Advantages

The advantages of Unipolar NRZ are −

It is simple.

A lesser bandwidth is required.

Disadvantages

The disadvantages of Unipolar NRZ are −

No error correction done.

Presence of low frequency components may cause the signal droop.

No clock is present.
Loss of synchronization is likely to occur (especially for long strings of 1s and
0s).

Unipolar Return to Zero RZ

In this type of unipolar signaling, a High in data, though represented by a Mark

pulse, its duration T0 is less than the symbol bit duration. Half of the bit duration
remains high but it immediately returns to zero and shows the absence of pulse
during the remaining half of the bit duration.

It is clearly understood with the help of the following figure.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 32/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

Advantages

The advantages of Unipolar RZ are −

It is simple.
The spectral line present at the symbol rate can be used as a clock.

Disadvantages

The disadvantages of Unipolar RZ are −

No error correction.
Occupies twice the bandwidth as unipolar NRZ.
The signal droop is caused at the places where signal is non-zero at 0 Hz.

Polar Signaling
There are two methods of Polar Signaling. They are −

Polar NRZ
Polar RZ

Polar NRZ

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 33/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

In this type of Polar signaling, a High in data is represented by a positive pulse, while
a Low in data is represented by a negative pulse. The following figure depicts this
well.

Advantages

The advantages of Polar NRZ are −

It is simple.
No low-frequency components are present.

Disadvantages

The disadvantages of Polar NRZ are −

No error correction.
No clock is present.
The signal droop is caused at the places where the signal is non-zero at 0 Hz.

Polar RZ

In this type of Polar signaling, a High in data, though represented by a Mark pulse,
its duration T0 is less than the symbol bit duration. Half of the bit duration remains
high but it immediately returns to zero and shows the absence of pulse during the
remaining half of the bit duration.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 34/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

However, for a Low input, a negative pulse represents the data, and the zero level
remains same for the other half of the bit duration. The following figure depicts this
clearly.

Advantages

The advantages of Polar RZ are −

It is simple.
No low-frequency components are present.

Disadvantages

The disadvantages of Polar RZ are −

No error correction.
No clock is present.
Occupies twice the bandwidth of Polar NRZ.
The signal droop is caused at places where the signal is non-zero at 0 Hz.

Bipolar Signaling
This is an encoding technique which has three voltage levels namely +, - and 0.
Such a signal is called as duo-binary signal.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 35/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

An example of this type is Alternate Mark Inversion AM I . For a 1, the voltage

level gets a transition from + to – or from – to +, having alternate 1s to be of equal
polarity. A 0 will have a zero voltage level.

Even in this method, we have two types.

Bipolar NRZ
Bipolar RZ

From the models so far discussed, we have learnt the difference between NRZ and
RZ. It just goes in the same way here too. The following figure clearly depicts this.

The above figure has both the Bipolar NRZ and RZ waveforms. The pulse duration
and symbol bit duration are equal in NRZ type, while the pulse duration is half of the
symbol bit duration in RZ type.

Advantages

Following are the advantages −

It is simple.
No low-frequency components are present.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 36/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

Occupies low bandwidth than unipolar and polar NRZ schemes.

This technique is suitable for transmission over AC coupled lines, as signal
drooping doesn’t occur here.
A single error detection capability is present in this.

Disadvantages

Following are the disadvantages −

No clock is present.
Long strings of data causes loss of synchronization.

Power Spectral Density

The function which describes how the power of a signal got distributed at various
frequencies, in the frequency domain is called as Power Spectral Density P S D.

PSD is the Fourier Transform of Auto-Correlation S imilaritybetweenobservations .

It is in the form of a rectangular pulse.

PSD Derivation

According to the Einstein-Wiener-Khintchine theorem, if the auto correlation function

or power spectral density of a random process is known, the other can be found
exactly.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 37/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

Hence, to derive the power spectral density, we shall use the time auto-correlation
(Rx (τ )) of a power signal x(t) as shown below.
Tp

1 2
Rx (τ ) = limTp →∞ ∫ −T p
x(t)x(t + τ )dt
Tp
2

Since x(t) consists of impulses, Rx (τ ) can be written as

1
Rx (τ ) = ∑ Rn δ(τ − nT )
T
n=−∞

Where
1
Rn = limN →∞ ∑ a k a k+n
N k

Getting to know that Rn = R−n for real signals, we have

1
Sx (w) = (R0 + 2 ∑ Rn cos nwT )
T
n=1

Since the pulse filter has the spectrum of (w) ↔ f (t), we have

2
sy (w) =∣ F (w) ∣ Sx (w)

∞
2
∣F (w)∣
−jnwTb
= ( ∑ Rn e )
T
n=−∞

∞
2
∣F (w)∣
= (R0 + 2 ∑ Rn cos nwT )
T
n=1

Hence, we get the equation for Power Spectral Density. Using this, we can find the
PSD of various line codes.

Data Encoding Techniques

Encoding is the process of converting the data or a given sequence of characters,
symbols, alphabets etc., into a specified format, for the secured transmission of
data. Decoding is the reverse process of encoding which is to extract the
information from the converted format.

Data Encoding

Encoding is the process of using various patterns of voltage or current levels to

represent 1s and 0s of the digital signals on the transmission link.

The common types of line encoding are Unipolar, Polar, Bipolar, and Manchester.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 38/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

Encoding Techniques
The data encoding technique is divided into the following types, depending upon the
type of data conversion.

Analog data to Analog signals − The modulation techniques such as

Amplitude Modulation, Frequency Modulation and Phase Modulation of analog
signals, fall under this category.
Analog data to Digital signals − This process can be termed as digitization,
which is done by Pulse Code Modulation P C M . Hence, it is nothing but
digital modulation. As we have already discussed, sampling and quantization
are the important factors in this. Delta Modulation gives a better output than
PCM.
Digital data to Analog signals − The modulation techniques such as
Amplitude Shift Keying AS K , Frequency Shift Keying F S K , Phase Shift
Keying P S K , etc., fall under this category. These will be discussed in
subsequent chapters.

Digital data to Digital signals − These are in this section. There are several
ways to map digital data to digital signals. Some of them are −

Non Return to Zero N RZ

NRZ Codes has 1 for High voltage level and 0 for Low voltage level. The main
behavior of NRZ codes is that the voltage level remains constant during bit interval.
The end or start of a bit will not be indicated and it will maintain the same voltage
state, if the value of the previous bit and the value of the present bit are same.

The following figure explains the concept of NRZ coding.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 39/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

If the above example is considered, as there is a long sequence of constant voltage

level and the clock synchronization may be lost due to the absence of bit interval, it
becomes difficult for the receiver to differentiate between 0 and 1.

There are two variations in NRZ namely −

NRZ - L N RZ– LEV EL

There is a change in the polarity of the signal, only when the incoming signal
changes from 1 to 0 or from 0 to 1. It is the same as NRZ, however, the first bit of
the input signal should have a change of polarity.

NRZ - I N RZ– I N V ERT ED

If a 1 occurs at the incoming signal, then there occurs a transition at the beginning
of the bit interval. For a 0 at the incoming signal, there is no transition at the
beginning of the bit interval.

NRZ codes has a disadvantage that the synchronization of the transmitter clock
with the receiver clock gets completely disturbed, when there is a string of 1s and
0s. Hence, a separate clock line needs to be provided.

Bi-phase Encoding
The signal level is checked twice for every bit time, both initially and in the middle.
Hence, the clock rate is double the data transfer rate and thus the modulation rate is
also doubled. The clock is taken from the signal itself. The bandwidth required for
this coding is greater.

There are two types of Bi-phase Encoding.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 40/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

Bi-phase Manchester
Differential Manchester

Bi-phase Manchester

In this type of coding, the transition is done at the middle of the bit-interval. The
transition for the resultant pulse is from High to Low in the middle of the interval, for
the input bit 1. While the transition is from Low to High for the input bit 0.

Differential Manchester

In this type of coding, there always occurs a transition in the middle of the bit
interval. If there occurs a transition at the beginning of the bit interval, then the
input bit is 0. If no transition occurs at the beginning of the bit interval, then the
input bit is 1.

The following figure illustrates the waveforms of NRZ-L, NRZ-I, Bi-phase Manchester
and Differential Manchester coding for different digital inputs.

Block Coding
Among the types of block coding, the famous ones are 4B/5B encoding and 8B/6T
encoding. The number of bits are processed in different manners, in both of these
processes.

4B/5B Encoding

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 41/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

In Manchester encoding, to send the data, the clocks with double speed is required
rather than NRZ coding. Here, as the name implies, 4 bits of code is mapped with 5
bits, with a minimum number of 1 bits in the group.

The clock synchronization problem in NRZ-I encoding is avoided by assigning an

equivalent word of 5 bits in the place of each block of 4 consecutive bits. These 5-bit
words are predetermined in a dictionary.

The basic idea of selecting a 5-bit code is that, it should have one leading 0 and it
should have no more than two trailing 0s. Hence, these words are chosen such
that two transactions take place per block of bits.

8B/6T Encoding

We have used two voltage levels to send a single bit over a single signal. But if we
use more than 3 voltage levels, we can send more bits per signal.

For example, if 6 voltage levels are used to represent 8 bits on a single signal, then
such encoding is termed as 8B/6T encoding. Hence in this method, we have as many
as 729 combinations for signal and 256 combinations for bits.
6 8
3 2

These are the techniques mostly used for converting digital data into digital signals
by compressing or coding them for reliable transmission of data.

Digital Communication - Pulse Shaping

After going through different types of coding techniques, we have an idea on how
the data is prone to distortion and how the measures are taken to prevent it from
getting affected so as to establish a reliable communication.

There is another important distortion which is most likely to occur, called as Inter-
Symbol Interference I S I .

Inter Symbol Interference

This is a form of distortion of a signal, in which one or more symbols interfere with
subsequent signals, causing noise or delivering a poor output.

Causes of ISI

The main causes of ISI are −

Multi-path Propagation

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 42/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

Non-linear frequency in channels

The ISI is unwanted and should be completely eliminated to get a clean output. The
causes of ISI should also be resolved in order to lessen its effect.

To view ISI in a mathematical form present in the receiver output, we can consider
the receiver output.

The receiving filter output y(t) is sampled at time ti = iTb (with i taking on integer
values), yielding −
∞

y(ti ) = μ ∑ a k p(iTb − kTb )

k=−∞

= μa i + μ ∑ a k p(iTb − kTb )

k=−∞

k≠i

In the above equation, the first term μa i is produced by the ith transmitted bit.

The second term represents the residual effect of all other transmitted bits on the
decoding of the ith bit. This residual effect is called as Inter Symbol Interference.

In the absence of ISI, the output will be −

y(ti ) = μa i

This equation shows that the ith bit transmitted is correctly reproduced. However,
the presence of ISI introduces bit errors and distortions in the output.

While designing the transmitter or a receiver, it is important that you minimize the
effects of ISI, so as to receive the output with the least possible error rate.

Correlative Coding
So far, we’ve discussed that ISI is an unwanted phenomenon and degrades the
signal. But the same ISI if used in a controlled manner, is possible to achieve a bit
rate of 2W bits per second in a channel of bandwidth W Hertz. Such a scheme is
called as Correlative Coding or Partial response signaling schemes.

Since the amount of ISI is known, it is easy to design the receiver according to the
requirement so as to avoid the effect of ISI on the signal. The basic idea of
correlative coding is achieved by considering an example of Duo-binary Signaling.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 43/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

Duo-binary Signaling

The name duo-binary means doubling the binary system’s transmission capability. To
understand this, let us consider a binary input sequence {ak} consisting of
uncorrelated binary digits each having a duration Ta seconds. In this, the signal 1 is
represented by a +1 volt and the symbol 0 by a -1 volt.

Therefore, the duo-binary coder output ck is given as the sum of present binary digit
ak and the previous value ak-1 as shown in the following equation.

c k = a k + a k−1

The above equation states that the input sequence of uncorrelated binary sequence
{ak} is changed into a sequence of correlated three level pulses {ck}. This
correlation between the pulses may be understood as introducing ISI in the
transmitted signal in an artificial manner.

Eye Pattern
An effective way to study the effects of ISI is the Eye Pattern. The name Eye
Pattern was given from its resemblance to the human eye for binary waves. The
interior region of the eye pattern is called the eye opening. The following figure
shows the image of an eye-pattern.

Jitter is the short-term variation of the instant of digital signal, from its ideal
position, which may lead to data errors.

When the effect of ISI increases, traces from the upper portion to the lower portion
of the eye opening increases and the eye gets completely closed, if ISI is very high.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 44/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

An eye pattern provides the following information about a particular system.

Actual eye patterns are used to estimate the bit error rate and the signal-to-
noise ratio.
The width of the eye opening defines the time interval over which the
received wave can be sampled without error from ISI.
The instant of time when the eye opening is wide, will be the preferred time
for sampling.
The rate of the closure of the eye, according to the sampling time, determines
how sensitive the system is to the timing error.
The height of the eye opening, at a specified sampling time, defines the
margin over noise.

Hence, the interpretation of eye pattern is an important consideration.

Equalization
For reliable communication to be established, we need to have a quality output. The
transmission losses of the channel and other factors affecting the quality of the
signal, have to be treated. The most occurring loss, as we have discussed, is the ISI.

To make the signal free from ISI, and to ensure a maximum signal to noise ratio, we
need to implement a method called Equalization. The following figure shows an
equalizer in the receiver portion of the communication system.

The noise and interferences which are denoted in the figure, are likely to occur,
during transmission. The regenerative repeater has an equalizer circuit, which
compensates the transmission losses by shaping the circuit. The Equalizer is feasible
to get implemented.

Error Probability and Figure-of-merit

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 45/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

The rate at which data can be communicated is called the data rate. The rate at
which error occurs in the bits, while transmitting data is called the Bit Error Rate
BE R .

The probability of the occurrence of BER is the Error Probability. The increase in
Signal to Noise Ratio SN R decreases the BER, hence the Error Probability also gets
decreased.

In an Analog receiver, the figure of merit at the detection process can be termed as
the ratio of output SNR to the input SNR. A greater value of figure-of-merit will be an
advantage.

Digital Modulation Techniques

Digital-to-Analog signals is the next conversion we will discuss in this chapter. These
techniques are also called as Digital Modulation techniques.

Digital Modulation provides more information capacity, high data security, quicker
system availability with great quality communication. Hence, digital modulation
techniques have a greater demand, for their capacity to convey larger amounts of
data than analog modulation techniques.

There are many types of digital modulation techniques and also their combinations,
depending upon the need. Of them all, we will discuss the prominent ones.

ASK – Amplitude Shift Keying

The amplitude of the resultant output depends upon the input data whether it should
be a zero level or a variation of positive and negative, depending upon the carrier
frequency.

FSK – Frequency Shift Keying

The frequency of the output signal will be either high or low, depending upon the
input data applied.

PSK – Phase Shift Keying

The phase of the output signal gets shifted depending upon the input. These are
mainly of two types, namely Binary Phase Shift Keying BP S K and Quadrature
Phase Shift Keying QP S K , according to the number of phase shifts. The other one
is Differential Phase Shift Keying DP S K which changes the phase according to the
previous value.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 46/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

M-ary Encoding
M-ary Encoding techniques are the methods where more than two bits are made to
transmit simultaneously on a single signal. This helps in the reduction of bandwidth.

The types of M-ary techniques are −

M-ary ASK
M-ary FSK
M-ary PSK

All of these are discussed in subsequent chapters.

Amplitude Shift Keying

Amplitude Shift Keying AS K is a type of Amplitude Modulation which represents
the binary data in the form of variations in the amplitude of a signal.

Any modulated signal has a high frequency carrier. The binary signal when ASK
modulated, gives a zero value for Low input while it gives the carrier output for
High input.

The following figure represents ASK modulated waveform along with its input.

To find the process of obtaining this ASK modulated wave, let us learn about the
working of the ASK modulator.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 47/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

ASK Modulator
The ASK modulator block diagram comprises of the carrier signal generator, the
binary sequence from the message signal and the band-limited filter. Following is the
block diagram of the ASK Modulator.

The carrier generator, sends a continuous high-frequency carrier. The binary

sequence from the message signal makes the unipolar input to be either High or
Low. The high signal closes the switch, allowing a carrier wave. Hence, the output
will be the carrier signal at high input. When there is low input, the switch opens,
allowing no voltage to appear. Hence, the output will be low.

The band-limiting filter, shapes the pulse depending upon the amplitude and phase
characteristics of the band-limiting filter or the pulse-shaping filter.

ASK Demodulator
There are two types of ASK Demodulation techniques. They are −

Asynchronous ASK Demodulation/detection

Synchronous ASK Demodulation/detection

The clock frequency at the transmitter when matches with the clock frequency at the
receiver, it is known as a Synchronous method, as the frequency gets

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 48/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

synchronized. Otherwise, it is known as Asynchronous.

Asynchronous ASK Demodulator

The Asynchronous ASK detector consists of a half-wave rectifier, a low pass filter, and
a comparator. Following is the block diagram for the same.

The modulated ASK signal is given to the half-wave rectifier, which delivers a positive
half output. The low pass filter suppresses the higher frequencies and gives an
envelope detected output from which the comparator delivers a digital output.

Synchronous ASK Demodulator

Synchronous ASK detector consists of a Square law detector, low pass filter, a
comparator, and a voltage limiter. Following is the block diagram for the same.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 49/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

The ASK modulated input signal is given to the Square law detector. A square law
detector is one whose output voltage is proportional to the square of the amplitude
modulated input voltage. The low pass filter minimizes the higher frequencies. The
comparator and the voltage limiter help to get a clean digital output.

Frequency Shift Keying

Frequency Shift Keying F S K is the digital modulation technique in which the
frequency of the carrier signal varies according to the digital signal changes. FSK is a
scheme of frequency modulation.

The output of a FSK modulated wave is high in frequency for a binary High input and
is low in frequency for a binary Low input. The binary 1s and 0s are called Mark and
Space frequencies.

The following image is the diagrammatic representation of FSK modulated waveform

along with its input.

To find the process of obtaining this FSK modulated wave, let us know about the
working of a FSK modulator.

FSK Modulator
The FSK modulator block diagram comprises of two oscillators with a clock and the
input binary sequence. Following is its block diagram.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 50/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

The two oscillators, producing a higher and a lower frequency signals, are connected
to a switch along with an internal clock. To avoid the abrupt phase discontinuities of
the output waveform during the transmission of the message, a clock is applied to
both the oscillators, internally. The binary input sequence is applied to the
transmitter so as to choose the frequencies according to the binary input.

FSK Demodulator
There are different methods for demodulating a FSK wave. The main methods of FSK
detection are asynchronous detector and synchronous detector. The
synchronous detector is a coherent one, while asynchronous detector is a non-
coherent one.

Asynchronous FSK Detector

The block diagram of Asynchronous FSK detector consists of two band pass filters,
two envelope detectors, and a decision circuit. Following is the diagrammatic
representation.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 51/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

The FSK signal is passed through the two Band Pass Filters BP F s , tuned to Space
and Mark frequencies. The output from these two BPFs look like ASK signal, which is
given to the envelope detector. The signal in each envelope detector is modulated
asynchronously.

The decision circuit chooses which output is more likely and selects it from any one
of the envelope detectors. It also re-shapes the waveform to a rectangular one.

Synchronous FSK Detector

The block diagram of Synchronous FSK detector consists of two mixers with local
oscillator circuits, two band pass filters and a decision circuit. Following is the
diagrammatic representation.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 52/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

The FSK signal input is given to the two mixers with local oscillator circuits. These
two are connected to two band pass filters. These combinations act as demodulators
and the decision circuit chooses which output is more likely and selects it from any
one of the detectors. The two signals have a minimum frequency separation.

For both of the demodulators, the bandwidth of each of them depends on their bit
rate. This synchronous demodulator is a bit complex than asynchronous type
demodulators.

Digital Communication - Phase Shift Keying

Phase Shift Keying P SK is the digital modulation technique in which the phase of
the carrier signal is changed by varying the sine and cosine inputs at a particular
time. PSK technique is widely used for wireless LANs, bio-metric, contactless
operations, along with RFID and Bluetooth communications.

PSK is of two types, depending upon the phases the signal gets shifted. They are −

Binary Phase Shift Keying BP SK

This is also called as 2-phase PSK or Phase Reversal Keying. In this technique, the
sine wave carrier takes two phase reversals such as 0° and 180°.

BPSK is basically a Double Side Band Suppressed Carrier DS BS C modulation

scheme, for message being the digital information.

Quadrature Phase Shift Keying QP SK

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 53/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

This is the phase shift keying technique, in which the sine wave carrier takes four
phase reversals such as 0°, 90°, 180°, and 270°.

If this kind of techniques are further extended, PSK can be done by eight or sixteen
values also, depending upon the requirement.

BPSK Modulator
The block diagram of Binary Phase Shift Keying consists of the balance modulator
which has the carrier sine wave as one input and the binary sequence as the other
input. Following is the diagrammatic representation.

The modulation of BPSK is done using a balance modulator, which multiplies the two
signals applied at the input. For a zero binary input, the phase will be 0° and for a
high input, the phase reversal is of 180°.

Following is the diagrammatic representation of BPSK Modulated output wave along

with its given input.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 54/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

The output sine wave of the modulator will be the direct input carrier or the inverted
180°phaseshif ted input carrier, which is a function of the data signal.

BPSK Demodulator
The block diagram of BPSK demodulator consists of a mixer with local oscillator
circuit, a bandpass filter, a two-input detector circuit. The diagram is as follows.

By recovering the band-limited message signal, with the help of the mixer circuit and
the band pass filter, the first stage of demodulation gets completed. The base band

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 55/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

signal which is band limited is obtained and this signal is used to regenerate the
binary message bit stream.

In the next stage of demodulation, the bit clock rate is needed at the detector circuit
to produce the original binary message signal. If the bit rate is a sub-multiple of the
carrier frequency, then the bit clock regeneration is simplified. To make the circuit
easily understandable, a decision-making circuit may also be inserted at the 2nd
stage of detection.

Quadrature Phase Shift Keying

The Quadrature Phase Shift Keying QP S K is a variation of BPSK, and it is also a
Double Side Band Suppressed Carrier DS BS C modulation scheme, which sends two
bits of digital information at a time, called as bigits.

Instead of the conversion of digital bits into a series of digital stream, it converts
them into bit pairs. This decreases the data bit rate to half, which allows space for
the other users.

QPSK Modulator
The QPSK Modulator uses a bit-splitter, two multipliers with local oscillator, a 2-bit
serial to parallel converter, and a summer circuit. Following is the block diagram for
the same.

At the modulator’s input, the message signal’s even bits (i.e., 2nd bit, 4th bit, 6th
bit, etc.) and odd bits (i.e., 1st bit, 3rd bit, 5th bit, etc.) are separated by the bits
splitter and are multiplied with the same carrier to generate odd BPSK (called as

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 56/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

PSKI) and even BPSK (called as PSKQ). The PSKQ signal is anyhow phase shifted
by 90° before being modulated.

The QPSK waveform for two-bits input is as follows, which shows the modulated
result for different instances of binary inputs.

QPSK Demodulator
The QPSK Demodulator uses two product demodulator circuits with local oscillator,
two band pass filters, two integrator circuits, and a 2-bit parallel to serial converter.
Following is the diagram for the same.

The two product detectors at the input of demodulator simultaneously demodulate

the two BPSK signals. The pair of bits are recovered here from the original data.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 57/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

These signals after processing, are passed to the parallel to serial converter.

Differential Phase Shift Keying

In Differential Phase Shift Keying DP S K the phase of the modulated signal is
shifted relative to the previous signal element. No reference signal is considered
here. The signal phase follows the high or low state of the previous element. This
DPSK technique doesn’t need a reference oscillator.

The following figure represents the model waveform of DPSK.

It is seen from the above figure that, if the data bit is Low i.e., 0, then the phase of
the signal is not reversed, but continued as it was. If the data is a High i.e., 1, then
the phase of the signal is reversed, as with NRZI, invert on 1
af ormof dif f erentialencoding.

If we observe the above waveform, we can say that the High state represents an M
in the modulating signal and the Low state represents a W in the modulating signal.

DPSK Modulator
DPSK is a technique of BPSK, in which there is no reference phase signal. Here, the
transmitted signal itself can be used as a reference signal. Following is the diagram
of DPSK Modulator.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 58/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

DPSK encodes two distinct signals, i.e., the carrier and the modulating signal with
180° phase shift each. The serial data input is given to the XNOR gate and the
output is again fed back to the other input through 1-bit delay. The output of the
XNOR gate along with the carrier signal is given to the balance modulator, to produce
the DPSK modulated signal.

DPSK Demodulator
In DPSK demodulator, the phase of the reversed bit is compared with the phase of
the previous bit. Following is the block diagram of DPSK demodulator.

From the above figure, it is evident that the balance modulator is given the DPSK
signal along with 1-bit delay input. That signal is made to confine to lower
frequencies with the help of LPF. Then it is passed to a shaper circuit, which is a
comparator or a Schmitt trigger circuit, to recover the original binary data as the
output.

Digital Communication - M-ary Encoding

The word binary represents two bits. M represents a digit that corresponds to the
number of conditions, levels, or combinations possible for a given number of binary
variables.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 59/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

This is the type of digital modulation technique used for data transmission in which
instead of one bit, two or more bits are transmitted at a time. As a single signal is
used for multiple bit transmission, the channel bandwidth is reduced.

M-ary Equation
If a digital signal is given under four conditions, such as voltage levels, frequencies,
phases, and amplitude, then M = 4.

The number of bits necessary to produce a given number of conditions is expressed

mathematically as

N = log2 M

Where

N is the number of bits necessary

M is the number of conditions, levels, or combinations possible with N bits.

The above equation can be re-arranged as

N
2 = M

For example, with two bits, 22 = 4 conditions are possible.

Types of M-ary Techniques

In general, Multi-level M − ary modulation techniques are used in digital
communications as the digital inputs with more than two modulation levels are
allowed on the transmitter’s input. Hence, these techniques are bandwidth efficient.

There are many M-ary modulation techniques. Some of these techniques, modulate
one parameter of the carrier signal, such as amplitude, phase, and frequency.

M-ary ASK

This is called M-ary Amplitude Shift Keying M − AS K or M-ary Pulse Amplitude

Modulation P AM .

The amplitude of the carrier signal, takes on M different levels.

Representation of M-ary ASK

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 60/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

Sm (t) = Am cos(2πfc t)

Am ϵ(2m − 1 − M )Δ, m = 1, 2... . M and 0 ≤ t ≤ Ts

Some prominent features of M-ary ASK are −

This method is also used in PAM.

Its implementation is simple.

M-ary ASK is susceptible to noise and distortion.

M-ary FSK

This is called as M-ary Frequency Shift Keying M − aryF S K .

The frequency of the carrier signal, takes on M different levels.

Representation of M-ary FSK

−−−
2E s π 0 ≤ t ≤ Ts and i = 1, 2, 3... . . M
Si (t) = √ cos( (nc + i) t)
Ts Ts

nc
Where fc =
2Ts
for some fixed integer n.

Some prominent features of M-ary FSK are −

Not susceptible to noise as much as ASK.

The transmitted M number of signals are equal in energy and duration.

The signals are separated by Hz making the signals orthogonal to each

1

2Ts

other.
Since M signals are orthogonal, there is no crowding in the signal space.
The bandwidth efficiency of M-ary FSK decreases and the power efficiency
increases with the increase in M.

M-ary PSK

This is called as M-ary Phase Shift Keying M − aryP S K .

The phase of the carrier signal, takes on M different levels.

Representation of M-ary PSK

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 61/75
3/25/24, 11:33 AM Digital Communication - Quick Guide
−−
−
2E 0 ≤ t ≤ T and i = 1, 2. . . M
Si (t) = √ cos(wo t + ϕi t)
T

2πi
ϕi (t) = where i = 1, 2, 3. . . . . . M
M

Some prominent features of M-ary PSK are −

The envelope is constant with more phase possibilities.

This method was used during the early days of space communication.
Better performance than ASK and FSK.
Minimal phase estimation error at the receiver.
The bandwidth efficiency of M-ary PSK decreases and the power efficiency
increases with the increase in M.

So far, we have discussed different modulation techniques. The output of all these
techniques is a binary sequence, represented as 1s and 0s. This binary or digital
information has many types and forms, which are discussed further.

Digital Communication - Information Theory

Information is the source of a communication system, whether it is analog or digital.
Information theory is a mathematical approach to the study of coding of
information along with the quantification, storage, and communication of
information.

Conditions of Occurrence of Events

If we consider an event, there are three conditions of occurrence.

If the event has not occurred, there is a condition of uncertainty.

If the event has just occurred, there is a condition of surprise.
If the event has occurred, a time back, there is a condition of having some
information.

These three events occur at different times. The difference in these conditions help
us gain knowledge on the probabilities of the occurrence of events.

Entropy

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 62/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

When we observe the possibilities of the occurrence of an event, how surprising or

uncertain it would be, it means that we are trying to have an idea on the average
content of the information from the source of the event.

Entropy can be defined as a measure of the average information content per source
symbol. Claude Shannon, the “father of the Information Theory”, provided a
formula for it as −

H = − ∑ pi logb pi

Where pi is the probability of the occurrence of character number i from a given

stream of characters and b is the base of the algorithm used. Hence, this is also
called as Shannon’s Entropy.

The amount of uncertainty remaining about the channel input after observing the
channel output, is called as Conditional Entropy. It is denoted by H (x ∣ y)

Mutual Information
Let us consider a channel whose output is Y and input is X

Let the entropy for prior uncertainty be X = Hx

T hisisassumedbef oretheinputisapplied

To know about the uncertainty of the output, after the input is applied, let us
consider Conditional Entropy, given that Y = yk

j−1
1
H (x ∣ yk ) = ∑ p (x j ∣ yk ) log2 [ ]
p(x j ∣ yk )
j=0

This is a random variable for H (X ∣ y = y0 ) . . . . . . . . . . . . . . . H (X ∣ y = yk ) with

probabilities p(y0 ) . . . . . . . . . . . . p(yk−1) respectively.

The mean value of H (X ∣ y = yk ) for output alphabet y is −

k−1

H (X ∣ Y ) = ∑ H (X ∣ y = yk ) p (yk )

k=0

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 63/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

=
k−1 j−1

∑ ∑ p (x j ∣ yk ) p (yk ) log2

k=0 j=0

1
[ ]
p (x j ∣ y k )

k−1 j−1
1
= ∑ ∑ p (x j , yk ) log2 [ ]
p (x j ∣ y k )
k=0 j=0

Now, considering both the uncertainty conditions

bef oreandaf terapplyingtheinputs, we come to know that the difference, i.e.
H (x) − H (x ∣ y) must represent the uncertainty about the channel input that is
resolved by observing the channel output.

This is called as the Mutual Information of the channel.

Denoting the Mutual Information as I (x; y) , we can write the whole thing in an
equation, as follows

I (x; y) = H (x) − H (x ∣ y)

Hence, this is the equational representation of Mutual Information.

Properties of Mutual information

These are the properties of Mutual information.

Mutual information of a channel is symmetric.

I (x; y) = I (y; x)

Mutual information is non-negative.

I (x; y) ≥ 0

Mutual information can be expressed in terms of entropy of the channel

output.

I (x; y) = H (y) − H (y ∣ x)

Where H (y ∣ x) is a conditional entropy

Mutual information of a channel is related to the joint entropy of the channel
input and the channel output.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 64/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

I (x; y) = H (x) + H (y) − H (x, y)

Where the joint entropy H (x, y) is defined by

j−1 k−1
1
H (x, y) = ∑ ∑ p(x j , yk ) log2 ( )
p (x i , y k )
j=0 k=0

Channel Capacity

We have so far discussed mutual information. The maximum average mutual

information, in an instant of a signaling interval, when transmitted by a discrete
memoryless channel, the probabilities of the rate of maximum reliable transmission
of data, can be understood as the channel capacity.

It is denoted by C and is measured in bits per channel use.

Discrete Memoryless Source

A source from which the data is being emitted at successive intervals, which is
independent of previous values, can be termed as discrete memoryless source.

This source is discrete as it is not considered for a continuous time interval, but at
discrete time intervals. This source is memoryless as it is fresh at each instant of
time, without considering the previous values.

Source Coding Theorem

The Code produced by a discrete memoryless source, has to be efficiently
represented, which is an important problem in communications. For this to happen,
there are code words, which represent these source codes.

For example, in telegraphy, we use Morse code, in which the alphabets are denoted
by Marks and Spaces. If the letter E is considered, which is mostly used, it is
denoted by “.” Whereas the letter Q which is rarely used, is denoted by “--.-”

Let us take a look at the block diagram.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 65/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

Where Sk is the output of the discrete memoryless source and bk is the output of
the source encoder which is represented by 0s and 1s.

The encoded sequence is such that it is conveniently decoded at the receiver.

Let us assume that the source has an alphabet with k different symbols and that the
kth symbol Sk occurs with the probability Pk, where k = 0, 1…k-1.

Let the binary code word assigned to symbol Sk, by the encoder having length lk,
measured in bits.

Hence, we define the average code word length L of the source encoder as

k−1
¯
¯¯¯
L = ∑ pk lk

k=0

L represents the average number of bits per source symbol

¯
¯¯¯
If L min = minimum possible value of L

Then coding efficiency can be defined as

Lmin
η =
¯
¯¯¯
L

¯
¯¯¯
With L ≥ L min we will have η ≤ 1

However, the source encoder is considered efficient when η = 1

For this, the value L min has to be determined.

Let us refer to the definition, “Given a discrete memoryless source of entropy H (δ),

the average code-word length L for any source encoding is bounded as L ≥ H (δ)."
¯
¯¯¯

In simpler words, the code word

example : M orsecodef orthewordQU E U E is−. −. . −. . . −.is always greater
than or equal to the source code QU E U E inexample. Which means, the symbols in
the code word are greater than or equal to the alphabets in the source code.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 66/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

Hence with L min = H (δ), the efficiency of the source encoder in terms of Entropy
H (δ) may be written as

H (δ)
η =
¯
¯¯¯
L

This source coding theorem is called as noiseless coding theorem as it establishes

an error-free encoding. It is also called as Shannon’s first theorem.

Channel Coding Theorem

The noise present in a channel creates unwanted errors between the input and the
output sequences of a digital communication system. The error probability should be
very low, nearly ≤ 10-6 for a reliable communication.

The channel coding in a communication system, introduces redundancy with a

control, so as to improve the reliability of the system. The source coding reduces
redundancy to improve the efficiency of the system.

Channel coding consists of two parts of action.

Mapping incoming data sequence into a channel input sequence.

Inverse Mapping the channel output sequence into an output data
sequence.

The final target is that the overall effect of the channel noise should be minimized.

The mapping is done by the transmitter, with the help of an encoder, whereas the
inverse mapping is done by the decoder in the receiver.

Channel Coding
Let us consider a discrete memoryless channel δ with Entropy H δ

Ts indicates the symbols that δ gives per second

Channel capacity is indicated by C

Channel can be used for every Tc secs

Hence, the maximum capability of the channel is C/Tc

H (δ)
The data sent = Ts

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 67/75
3/25/24, 11:33 AM Digital Communication - Quick Guide
H (δ)
If it means the transmission is good and can be reproduced with a small
C
≤
Ts Tc

probability of error.

In this, is the critical rate of channel capacity.

C

Tc

H (δ)
If then the system is said to be signaling at a critical rate.
C
=
Ts Tc

H (δ)
Conversely, if , then the transmission is not possible.
C
>
Ts Tc

Hence, the maximum rate of the transmission is equal to the critical rate of the
channel capacity, for reliable error-free messages, which can take place, over a
discrete memoryless channel. This is called as Channel coding theorem.

Digital Communication - Error Control Coding

Noise or Error is the main problem in the signal, which disturbs the reliability of the
communication system. Error control coding is the coding procedure done to
control the occurrences of errors. These techniques help in Error Detection and Error
Correction.

There are many different error correcting codes depending upon the mathematical
principles applied to them. But, historically, these codes have been classified into
Linear block codes and Convolution codes.

Linear Block Codes

In the linear block codes, the parity bits and message bits have a linear combination,
which means that the resultant code word is the linear combination of any two code
words.

Let us consider some blocks of data, which contains k bits in each block. These bits
are mapped with the blocks which has n bits in each block. Here n is greater than k.
The transmitter adds redundant bits which are n − k bits. The ratio k/n is the code
rate. It is denoted by r and the value of r is r < 1.

The n − k bits added here, are parity bits. Parity bits help in error detection and
error correction, and also in locating the data. In the data being transmitted, the left
most bits of the code word correspond to the message bits, and the right most bits
of the code word correspond to the parity bits.

Systematic Code

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 68/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

Any linear block code can be a systematic code, until it is altered. Hence, an
unaltered block code is called as a systematic code.

Following is the representation of the structure of code word, according to their

allocation.

If the message is not altered, then it is called as systematic code. It means, the
encryption of the data should not change the data.

Convolution Codes
So far, in the linear codes, we have discussed that systematic unaltered code is
preferred. Here, the data of total n bits if transmitted, k bits are message bits and
n − k bits are parity bits.

In the process of encoding, the parity bits are subtracted from the whole data and
the message bits are encoded. Now, the parity bits are again added and the whole
data is again encoded.

The following figure quotes an example for blocks of data and stream of data, used
for transmission of information.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 69/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

The whole process, stated above is tedious which has drawbacks. The allotment of
buffer is a main problem here, when the system is busy.

This drawback is cleared in convolution codes. Where the whole stream of data is
assigned symbols and then transmitted. As the data is a stream of bits, there is no
need of buffer for storage.

Hamming Codes
The linearity property of the code word is that the sum of two code words is also a
code word. Hamming codes are the type of linear error correcting codes, which
can detect up to two bit errors or they can correct one bit errors without the
detection of uncorrected errors.

While using the hamming codes, extra parity bits are used to identify a single bit
error. To get from one-bit pattern to the other, few bits are to be changed in the
data. Such number of bits can be termed as Hamming distance. If the parity has a
distance of 2, one-bit flip can be detected. But this can't be corrected. Also, any two
bit flips cannot be detected.

However, Hamming code is a better procedure than the previously discussed ones in
error detection and correction.

BCH Codes
BCH codes are named after the inventors Bose, Chaudari and Hocquenghem. During
the BCH code design, there is control on the number of symbols to be corrected and

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 70/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

hence multiple bit correction is possible. BCH codes is a powerful technique in error
correcting codes.

For any positive integers m ≥ 3 and t < 2m-1 there exists a BCH binary code.
Following are the parameters of such code.

Block length n = 2m-1

Number of parity-check digits n - k ≤ mt

Minimum distance dmin ≥ 2t + 1

This code can be called as t-error-correcting BCH code.

Cyclic Codes
The cyclic property of code words is that any cyclic-shift of a code word is also a
code word. Cyclic codes follow this cyclic property.

For a linear code C, if every code word i.e., C = C 1, C 2, . . . . . . C n from C has a

cyclic right shift of components, it becomes a code word. This shift of right is equal
to n-1 cyclic left shifts. Hence, it is invariant under any shift. So, the linear code C,
as it is invariant under any shift, can be called as a Cyclic code.

Cyclic codes are used for error correction. They are mainly used to correct double
errors and burst errors.

Hence, these are a few error correcting codes, which are to be detected at the
receiver. These codes prevent the errors from getting introduced and disturb the
communication. They also prevent the signal from getting tapped by unwanted
receivers. There is a class of signaling techniques to achieve this, which are
discussed in the next chapter.

Spread Spectrum Modulation

A collective class of signaling techniques are employed before transmitting a signal
to provide a secure communication, known as the Spread Spectrum Modulation.
The main advantage of spread spectrum communication technique is to prevent
“interference” whether it is intentional or unintentional.

The signals modulated with these techniques are hard to interfere and cannot be
jammed. An intruder with no official access is never allowed to crack them. Hence,
these techniques are used for military purposes. These spread spectrum signals
transmit at low power density and has a wide spread of signals.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 71/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

Pseudo-Noise Sequence

A coded sequence of 1s and 0s with certain auto-correlation properties, called as

Pseudo-Noise coding sequence is used in spread spectrum techniques. It is a
maximum-length sequence, which is a type of cyclic code.

Narrow-band and Spread-spectrum Signals

Both the Narrow band and Spread spectrum signals can be understood easily by
observing their frequency spectrum as shown in the following figures.

Narrow-band Signals

The Narrow-band signals have the signal strength concentrated as shown in the
following frequency spectrum figure.

Following are some of its features −

Band of signals occupy a narrow range of frequencies.

Power density is high.
Spread of energy is low and concentrated.

Though the features are good, these signals are prone to interference.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 72/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

Spread Spectrum Signals

The spread spectrum signals have the signal strength distributed as shown in the
following frequency spectrum figure.

Following are some of its features −

Band of signals occupy a wide range of frequencies.

Power density is very low.
Energy is wide spread.

With these features, the spread spectrum signals are highly resistant to interference
or jamming. Since multiple users can share the same spread spectrum bandwidth
without interfering with one another, these can be called as multiple access
techniques.

FHSS and DSSS / CDMA

Spread spectrum multiple access techniques uses signals which have a transmission
bandwidth of a magnitude greater than the minimum required RF bandwidth.

These are of two types.

Frequency Hopped Spread Spectrum F HSS

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 73/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

Direct Sequence Spread Spectrum DS S S

Frequency Hopped Spread Spectrum F HSS

This is frequency hopping technique, where the users are made to change the
frequencies of usage, from one to another in a specified time interval, hence called
as frequency hopping. For example, a frequency was allotted to sender 1 for a
particular period of time. Now, after a while, sender 1 hops to the other frequency
and sender 2 uses the first frequency, which was previously used by sender 1. This is
called as frequency reuse.

The frequencies of the data are hopped from one to another in order to provide a
secure transmission. The amount of time spent on each frequency hop is called as
Dwell time.

Direct Sequence Spread Spectrum DSSS

Whenever a user wants to send data using this DSSS technique, each and every bit
of the user data is multiplied by a secret code, called as chipping code. This
chipping code is nothing but the spreading code which is multiplied with the original
message and transmitted. The receiver uses the same code to retrieve the original
message.

Comparison between FHSS and DSSS/CDMA

Both the spread spectrum techniques are popular for their characteristics. To have a
clear understanding, let us take a look at their comparisons.

FHSS DSSS / CDMA

Multiple frequencies are used Single frequency is used

Hard to find the user’s frequency at any User frequency, once allotted is always
instant of time the same

Frequency reuse is allowed Frequency reuse is not allowed

Sender has to wait if the spectrum is

Sender need not wait
busy

Power strength of the signal is high Power strength of the signal is low

Stronger and penetrates through the It is weaker compared to FHSS

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 74/75
3/25/24, 11:33 AM Digital Communication - Quick Guide

obstacles

It is never affected by interference It can be affected by interference

It is cheaper It is expensive

This is the commonly used technique This technique is not frequently used

Advantages of Spread Spectrum

Following are the advantages of spread spectrum −

Cross-talk elimination
Better output with data integrity
Reduced effect of multipath fading
Better security

Reduction in noise
Co-existence with other systems
Longer operative distances
Hard to detect
Not easy to demodulate/decode
Difficult to jam the signals

Although spread spectrum techniques were originally designed for military uses, they
are now being used widely for commercial purpose.

https://www.tutorialspoint.com/digital_communication/digital_communication_quick_guide.htm 75/75