CALC BY: DATE:

C-PURLIN DESIGN CHECK BY: DATE:

CONTENT: C-PURLIN MARK:

Purlin Loads
Section Properties kpa kn/m
H = 100 mm Depth of Purlin Wsw = 0.028 Purlin Self weight
B = 50 mm Width of purlin Wdl = 0.58 0.406 weight Ceiling & framing
t = 1.6 mm Thickness of purlin wDT = 0.434 Total Deadload
As = 368 sq.mm cross sectional area wLL = 1 0.7 Liveloads
Lw = 0.028 kn/m Linear weight
Zx = 12000 mm3 Elastic modulus about x-axis Wind Pressure ( 280 kPh )
Zy = 4000 mm3 Elastic modulus about y-axis kPa kN/m
ww = 1.67 1.169 windward direction
Material Properties lw = -0.56 -0.392 leeward direction
fy = 248 Mpa yield strength
fu = 400 Mpa Ultimate strength

Roof Framing layout

S = 2 m Distance between rafter/trusses
Lo = 0.2 m Lenght of Overhang
Sp = 0.7 m Spacing of purlin
θ = 6.34 degrees Roof Angle
No Sagrod
Muy = WtL^2/8
Mux = WnL^2/8

Design Calculations

U = 1.2D + 1.0W + 0.5Lr

wN = 1.424 kn/m 1.2wDcosθ + 0.5wLcosθ+1.0W
wT = 0.0673 kN/m 1.2wDsinθ + 0.5 wLsinsθ+1.0W
fbx = 59.34 mPa OK !
fby = 8.41 mPa OK !
Allowable Bending stress fbx/Fbx + fby/Fby ≤ 1
= 15.63 bf/2tf 0.46 OK ! fbx/Fbx + fby/Fby
= 10.8 170/√(fy)
= 15.9 250/√(fy) Stress Due to Deadload + Live Load + Leeward
bf/2tf > 250/√(fy) --non compact U=1.2D+1.6Lr+0.5W
wN = 1.004 kn/m 1.2wDcosθ + 1.6wLcosθ+0.5W
= 148.8 mpa Fbx wT = 0.1268 kN/m 1.2wDsinθ + 1.6wLsinsθ+0.5W
= 186 mpa Fby (0.75 fy ) fbx = 41.85 mPa OK !
fby = 15.85 mPa OK !
COMPUTATIONS fbx/Fbx + fby/Fby ≤ 1
Mux = 41.7 wN wNL^2/Sx = 0.38 OK ! fbx/Fbx + fby/Fby
Muy = 125.0 wT wTL^2/Sy
U = 1.2D + 1.0W + 0.5Lr
Stress Due to Selfweight of Purlin wN = 0.331 kn/m 1.2wDcosθ +0.5wLcosθ+1.0W
wN = 0.033 kn/m 1.2*wP*cosθ wT = 0.0673 kN/m 1.2wDsinθ +0.5 wLsinsθ+1.0W
wT = 0.0043 kN/m 1.2*wP*sinθ fbx = 15.20 mPa OK !
fbx = 1.39 mPa OK ! fby = 8.96 mPa OK !
fby = 0.54 mPa OK ! fbx/Fbx + fby/Fby ≤ 1
= 0.16 OK ! fbx/Fbx + fby/Fby
Stress Due to Deadload + Live Load
U= 1.2D + 0.5Lr SAG ROD
wN = 0.606 kn/m 1.2wDcosθ + 0.5wLcosθ hmax = 1 m top elevation of truss/rafter
wT = 0.4444 kN/m 1.2wDsinθ + 0.5wLsinsθ S = 2.44 m Span of truss /rafter
fbx = 26.63 mPa OK ! T Nb = 4 pcs Total No. of Purlins
fby = 56.09 mPa OK !
fbx/Fbx + fby/Fby ≤ 1 Midspan SagRod
= 0.49 OK ! fbx/Fbx + fby/Fby R = 0.561 kN R=5wTL/8
1/3 SagRod
Stress Due to Deadload + Live Load + Windward R = 0.33 kN R = 11wTL/30
U=1.2D+1.6Lr+0.5W Total Load on Critical SagRod ( it will supports 4 purlins )
wN = 1.551 kn/m 1.2wDcosθ + 1.6wLcosθ+0.5W Tu = 2.243 kN
wT = 0.1268 kN/m 1.2wDsinθ + 1.6wLsinsθ+0.5W Areq. = 17.00 sq.mm
fbx = 66.00 mPa OK ! db = 4.65 mm A=πd^2/4
fby = 16.40 mPa OK !
fbx/Fbx + fby/Fby ≤ 1
= 0.54 OK ! fbx/Fbx + fby/Fby

PURLIN SAGROD DESIGN Page 1 of 1