Scribd
Upload
19 views

Midterm 2007

This document contains a midterm exam for an instrumentation and computers course. The exam covers topics from three labs on A/D conversion, thermocouple calibration, and thermal behavior modeling. It consists of 30 multiple choice and short answer questions testing understanding of instrumentation concepts like sensitivity, time constant, probability, calibration, and A/D conversion.

Uploaded by

k.ghanem
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
19 views

Midterm 2007

This document contains a midterm exam for an instrumentation and computers course. The exam covers topics from three labs on A/D conversion, thermocouple calibration, and thermal behavior modeling. It consists of 30 multiple choice and short answer questions testing understanding of instrumentation concepts like sensitivity, time constant, probability, calibration, and A/D conversion.

Uploaded by

k.ghanem
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

MAE334 - Introduction to Instrumentation and Computers

Midterm Examination

October 24, 2007

USE A #2 Pencil
o Closed Book and Notes

o No Calculators
1. Fill in your name on side 2 of the
scoring sheet (Last name first!)
2. Fill in your 8-digit person
number on your scoring sheet.

3. Fill in circle 1 under GRADE


OR EDUCATION on your scoring
sheet. This is your test number!
You will receive a ZERO if you do
not indicate your test number.
o For each question, choose THE
BEST ANSWER and mark the
corresponding answer on the
scoring sheet.

The terms lab 1, lab 2, and lab 3 refer to: Lab 1 Basics of A to D
Conversion and Lab 2 Thermocouple, Static and Dynamic
Calibration and Lab 3 Transient Thermal Behavior with Work and
Heat Loss.

All multiple choice questions are worth 1 point.


All short answer questions are worth 2 points.
Total 24 + 2x12 = 36 points (Quizzes are worth 20 points)
1. The static sensitivity of the thermocouple calibrated in the second lab was
constant (for both water and air use).
a. True
b. False
2. The time constant, , of the thermocouple used in the second lab was constant
for both water and air use.
a. True
b. False
3. Impatience while doing the static calibration of the thermocouple in the second
lab
a. would contribute to hysteresis error.
b. would exaggerate the bias error.
c. would minimize Sxy.
d. All of the above
e. None of the above
4. What portion of the repeated sampling of a static temperature signal are within
one standard deviation of the true mean value?
a. 5%
b. 50%
c. 68%
d. 95%
5. A zero order sensor will attenuate and delay the output with respect to the input.
a. True
b. False
6. The frequency bandwidth of a first order instrument is defined as the frequency
below which M(ω)=0.707, or output/input power is -3 dB.
a. True
b. False
7. The most common dial pressure gauge contains a Bourdon Tube.
a. True
b. False
8. The variance is equal to the standard deviation of signal.
a. True
b. False
-x/C
9. An exponential equation, y(x) = A + Be , fit to a data set with 25 points has
how many degrees of freedom?
a. 21
b. 22
c. 23
d. 24
10. A correlation coefficient, R, of 0.92, indicates a high quality fit to the data.
a. True
b. False

MAE 334 – Midterm Exam, October 25, 2006 2 of 6


First-order system frequency response: Magnitude Ratio,
M(f)
1.1
1.0
0.9
0.8
0.7
0.6
0.5
M(f)

0.4
0.3
0.2
0.1
0.0
1 10 100 1000 10000 100000
frequency (Hertz)

Figure 1. Magnitude Ratio, (output/input vs. frequency), of first order sensor like
the thermocouple used in Lab 2.

11. The approximate time constant, , of the thermocouple response plotted in


Figure 1 is:
a. 1/100 seconds
b. 1 seconds
c. 100 seconds
d. 10 seconds
e. 40 seconds
12. A very small, very sensitive thermocouple will reach a steady state value sooner
for a small step input than a large step input.
a. True
b. False
13. An instrument’s accuracy is a measure of the random fluctuations in output for
repeated applications of the same input.
a. True
b. False
14. Which ADC setup would result in the best approximation of the mean value of
the function: ?
a. 1,000 samples at 2,000 samples/second
b. 1,000 samples at 1,000 samples/second
c. 1,000 samples at 10 samples/second
d. 5,000 samples at 10,000 samples/second
e. 5,000 samples at 5,000 samples/second

MAE 334 – Midterm Exam, October 25, 2006 3 of 6


Pressure Transducer Reponse
to a 2 PSI Step Input

2
Response (PSI)

0
0 1 2 3 4 5 6
Time (seconds)

Figure 2. Pressure transducer time response to a step input function.


15. The settling time in seconds of the pressure transducer plotted in Figure 2 is
approximately
a. 1
b. 2
c. 3
d. 4
e. 5
16. The ADC architecture normally associated with the fastest conversion rate is
a. Flash
b. Pipelined
c. Successive approximation
d. Sigma-delta
17. A 95 Hz sine wave sampled at 100 Hz will result in a sampled data set with
what frequency
a. 95 Hz
b. 5 Hz
c. 45 Hz
d. 55 Hz
e. none of the above
18. Heat loss to the laboratory surroundings from the calorimeter used in lab 3 was
modeled with the equation, )
a. True b. False

MAE 334 – Midterm Exam, October 25, 2006 4 of 6


Probability Distribution Functions
0.3

0.25

0.2
a)
0.15 b)
c)
0.1
d)
0.05

0
-10 -5 0 5 10

Figure 3. Sample probability functions, p(x).


19. Which of the probability distribution functions in Figure 3 has the smallest
standard deviation?

Figure 4. Example thermocouple connection configuration.


20. The thermocouple configuration in Figure 4 will measure what temperature if the
junction is at constant temperature (T4 = T3 ≠ T2 ≠ T1)?
a. (T1 – T2)
b. (T1 – T2) – T3
c. (T1 – T3) + (T2 – T4)
d. None of the above
21. For a normal distribution of xi about some sample mean value, ,
the confidence or precision interval is expressed as:
a. (P%)
b. (P%)
c. (P%)
d. None of the above

MAE 334 – Midterm Exam, October 25, 2006 5 of 6


22. Ambient temperature and barometric pressure are frequently extraneous
Short Answer Section Name:_______________________ Person Number:___________________
variables.
a. True b. False
23. A temperature sensor with infinite input impedance would be a “null device”.
a. True b. False
24. Excel LINEST regression analysis minimizes, , the sum of the
differences between the calibration data, yi, and the calibration curve, yci,.
a. True
b. False
25. The ADC used in the lab
would output what binary
value corresponding to -7?

26. As used in this class the confidence interval of a linear fit is

27. What is the equation for the error function, (t), used in lab 2 to linearize the
thermocouple response?

28. What is the equation used to calculate the damped or ringing frequency, d, of
an under damped second order sensor like the one plotted in Figure 2 in terms
of natural frequency, n , and the damping ratio, .

29. An analog to digital converter (ADC) quantization step size is defined in terms of
the input range, EFSR, Gain and the number of ADC bits, M, with the equation:

30. What is the equation used to determine the output/input signal magnitude, M( ),
in terms of the time constant, , and the input frequency :

MAE 334 – Midterm Exam, October 25, 2006 6 of 6

You might also like