80.51.0.240.

x000 1 2
ENGLISH
UN (24...240) V AC (50/60 Hz) /DC
Umin 17 V AC / DC 4 4a 4b 80.51 MODULAR TIMER, MULTI-FUNCTION
Umax 265 V AC / DC 1 FRONT VIEW
P < 1.8 VA (50 Hz) / <1 W 2a 80.51.0.240.P000 2b A Time scale rotary selector (Tmax)
B Time setting (Tmin...Tmax)
1 CO (SPDT) C LED
8 A 250 V AC D Function rotary selector
A
AC1 2000 VA 1 1 2 TERMINAL PUSH-IN CONNECTION
AC15 (230 V AC) 400 VA B 2a Connection with stranded wire (without screwdriver in case of solid wire)
C 2b Disconnection of the electrical connection
M (230 V AC) 0.3 kW
DC1 (30/110/220) V (8/0.3/0.12)A 3 TIME SCALES
D (Eg. T =10 min: set A=20 m and B =10)
88.8 mm
(–20...+60)°C 2 PI PE 4 WIRING DIAGRAM AND FUNCTIONS
PI PE
60.8 mm NOTE
2 Time scale and function must be set before energising the timer
IP20 17.5 mm 4a Without signal START functions:
80.51 80.51-P Start via contact in supply line (A1)
AI On-delay
PI PE DI Interval PI PE
LED UN SW Symmetrical flasher (starting pulse on)
4b External START functions:
– 15 - 18 15 - 16 10mm 10mm Start via contact into control terminal (B1)
BE Off- delay with control signal
√ 15 - 18 15 - 16 CE On- and off- delay with control signal
(1x6 / 2x4) mm2 (1x4 / 2x2.5) mm2 DE Interval with control signal on
(0.75...1.5) mm2 (0.75...2.5) mm2
√ 15 - 16 (1x10 / 2x12) AWG (1x12 / 2x14) AWG (18...16) AWG (18...14) AWG
PI PE 4c Possible
PI to control
PE an external load, such as another relay coil or
timer, connected to the signal start terminal B1
√ 15 - 16 15 - 18 4d With DC supply, positive polarity has to be connected to B1 terminal
(according to EN 60204 -1)
4e A voltage other than the supply voltage can be applied to the
command Start (B1), example:
A1- A2 = 230 V AC
B1-A2 = 24 V DC
3 OTHER DATA
Minimum control impulse: 50 ms.
A Recovery time: 100 ms.
• Open Type Device
35 mm rail mount (EN 60715).
• Pollution degree 2 Installation Environment
4d WORKING CONDITIONS
4c 4e
• Maximum Surrounding Air Temperature 40°C In conformity with the European Directive on EMC 2014/30/EU, the
• Use 60/75°C copper (Cu) conductor only and timer relay has a level of immunity, against radiated and conducted
wire ranges No. 14–18 AWG, stranded or solid B disturbances, considerably higher than requirements of EN 61812-1
• Terminal tightening torque of 7.1 Ib.in. (0.8 Nm) standard. However, devices like transformers, motors, contactors, switches
and power cables may cause disturbances and even damage the timer
80.51.0.240.P000 electronic circuit. For that reason, the wiring cables must be as short as
possible, and, when necessary, the timer shall be protected by the relevant
RC network, varistor or surge voltage protector.

Utility Model - IB8051VXX - 02/23 - Finder S.p.A. con unico socio - 10040 ALMESE (TO) - ITALY