SET A

Reg. No:
Gnanamani College of Technology, Namakkal-637018
Accredited by NBA & NAAC “A” Grade
Affiliated to Anna University, Chennai

Unit Test-I
B.E / B.Tech-Information Technology,
Programme &
Biomedical Engineering, Mechanical Year/Sem I/II
Branch
Engineering
Subject Code / 23GE102-Basic Electrical and Electronics
Date
Name Engineering
Examination
Maximum Marks 50 Marks 1:30 Hours
Duration
PART-A (5×2=10)
Answer All Questions
Blooms
Q.No Cos Questions Marks
Level
1 CO1 L1 State Ohm’s law 2
CO1
2 L1 State Kirchoff’s current law. 2
CO1 L2
3 Define active and passive networks. 2

4 CO1 L2 What is meant by average value? 2

CO1 L2
5 Define power factor. 2
PART-B (4 x 10 = 40)
Answer Any Four Questions
Determine the current supplied by each battery in the circuit by
using mesh analysis

6 CO1 L4 10

Solve the mesh and branch currents shown in fig

7 CO1 L4 10
 Use nodal analysis to determine the voltage across 5Ω resistance
and the current in the 12V source.

8 CO1 L3 10

CO1 A 100Ω resistor and a 20Mh inductor are connected in series across
a 230V, 50Hz supply. Find circuit impedance , admittance, current ,
9 L4 10
voltage across resistance voltage across inductor, apparent power
active power and power factor
CO1 Briefly explain about RMS Value, instantaneous value, form factor
10 L2 10
and peak factor.
CO1
11 L2 Derive the RLC series circuit 10

* BL: L1-Remembering, L2-Understanding, L3-Applying, L4-Analyzing, L5-Evaluating, L6-Creating.

Prepared by HoD IQAC Coordinator

SET B
Reg. No:
 Gnanamani College of Technology, Namakkal-637018
Accredited by NBA & NAAC “A” Grade
Affiliated to Anna University, Chennai

Unit Test-I
B.E / B.Tech-Information Technology,
Programme &
Biomedical Engineering, Mechanical Year/Sem I/II
Branch
Engineering
Subject Code / 23GE102-Basic Electrical and Electronics
Date
Name Engineering
Examination
Maximum Marks 50 Marks 1:30 Hours
Duration
PART-A (5×2=10)
Answer All Questions
Blooms
Q.No Cos Questions Marks
Level
1 CO1 L1 Define Electric current. 2
CO1
2 L1 State Kirchoff’s Voltage law. 2
CO1 L2
3 Mention the limitation of Ohm’s law. 2

4 CO1 L2 What is meant by RMS Value? 2

CO1 L2
5 Define frequency. 2
PART-B (4 x 10 = 40)
Answer Any Four Questions
Determine the value of load current and power delivered to the load
by using Mesh analysis method.

6 CO1 L4 10

Determine the mesh and branch currents shown in figure.

7 CO1 L4 10

Calculate the voltage across the 15Ω resistor in the network shown
in figure below using nodal analysis.
8 CO1 L3 10
 A coil of resistance 5Ω and inductance 100Mh is connected in series
with a 200µf capacitor across a 220V, 50Hz supply. Calculate
9 CO1 L4 (i)inductive reactance (ii) Capacitive reactance (iii). Impedance 10
(iv). The current (v). the power factor (vi) total power

CO1 Briefly explain about Average value, instantaneous value, form

10 L2 10
factor and peak factor and frequency
11 CO1 L2 Derive the RL series circuit 10

* BL: L1-Remembering, L2-Understanding, L3-Applying, L4-Analyzing, L5-Evaluating, L6-Creating.

Prepared by HoD IQAC Coordinator

SET B
Reg. No:

Gnanamani College of Technology, Namakkal-637018

Accredited by NBA & NAAC “A” Grade
Affiliated to Anna University, Chennai

Internal Assessment Test-I

Programme & B.E –Electrical and Electronics
Year/Sem III/V
Branch Engineering
Course Code C215 Date 14.09.2023
Subject Code /
EE3009 SPECIAL ELECTRICAL MACHINES Regulation R2021
Name
Examination
Maximum Marks 50 Marks 1:30 Hours
Duration
PART-A (5×2=10)
Answer All Questions
Blooms
Q.No Cos Questions Marks
Level
1 CO1 L1 Differential between VR, PM and hybrid stepper motor. 2

2 CO1 L1 Draw the typical dynamic characteristics of a stepper motor. 2

3 CO2 L2 What is the significance of closed loop control in SRM? 2

4 CO2 L1 Why rotor position sensor is essential for the operation of SRM? 2

5 CO3 L1 List the types of permanent magnet materials used in PMDC motor. 2
PART-B (4 x 10 = 40)
Answer Any Four Questions
6 CO1 L2 Derive the torque equation of VR stepper motor. 10

7 CO1 L4 Explain static and dynamic characteristics of a stepper motor. 10

 8 CO1 L1 Explain the mechanism of torque production in VR stepper motor. 10

9 CO2 L1 Explain the construction and working principle of SRM. 10

10 CO2 L1 What are the different types of power controllers used for SRM? 10
Sketch the structure of controller for PMBLDC motor and explain
11 CO3 L2 10
the function of various blocks.

* BL: L1-Remembering, L2-Understanding, L3-Applying, L4-Analyzing, L5-Evaluating, L6-Creating.

Prepared by HoD IQAC Coordinator