Scribd
Upload
16 views

Modul Ospf Sederhana Termasuk Script

Uploaded by

Novi Haryanto
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
16 views

Modul Ospf Sederhana Termasuk Script

Uploaded by

Novi Haryanto
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

11.6.1: Basic OSPF Configuration Lab.

Default Gateway
Device Interface IP Address Subnet Mask

Fa0/0 172.16.1.17 255.255.255.240 N/A


R1 S0/0/0 192.168.10.1 255.255.255.252 N/A
S0/0/1 192.168.10.5 255.255.255.252 N/A
Fa0/0 10.10.10.1 255.255.255.0 N/A
R2 S0/0/0 192.168.10.2 255.255.255.252 N/A
S0/0/1 192.168.10.9 255.255.255.252 N/A
Fa0/0 172.16.1.33 255.255.255.248 N/A
R3 S0/0/0 192.168.10.6 255.255.255.252 N/A
S0/0/1 192.168.10.10 255.255.255.252 N/A
PC1 NIC 172.16.1.20 255.255.255.240 172.16.1.17
PC2 NIC 10.10.10.10 255.255.255.0 10.10.10.1
PC3 NIC 172.16.1.35 255.255.255.248 172.16.1.33

Instructions:

Learn to Configure Basic OSPF

Learning Objectives

Cable a network according to the Topology Diagram


Erase the startup configuration and reload a router to the default state
Perform basic configuration tasks on a router
Configure and activate interfaces
Configure OSPF routing on all routers
Configure OSPF router IDs
Verify OSPF routing using show commands
Configure a static default route
Propagate default route to OSPF neighbors
Configure OSPF Hello and Dead Timers
Configure OSPF on a Multiaccess network
Configure OSPF priority
Understand the OSPF election process
Document the OSPF configuration

Task 2: Basic Router Configurations

Perform basic configuration of the R1, R2, and R3 routers according to the following guidelines:

Configure the router hostname


Disable DNS lookup
Configure the EXEC mode password as class
Configure a password for console connections as cisco (case sensitive)
Configure a password for VTY connections as cisco (case sensitive)
Task 3: Configure and Activate Serial and Ethernet Addresses
Step 1 Configure the interfaces on the R1, R2, and R3 routers with the IP addresses from the table

Task 4: Configure OSPF on the R1 Router

Step 1 Configure OSPF with a process ID number of 1, advertise all networks.

Task 5: Configure OSPF on the R2 and R3 Routers

Step 1 Configure OSPF with a process ID number of 1, advertise all networks.

Task 6: Configure OSPF Router IDs


Step 1 Configure R1 with a Loopback0 interface of 10.1.1.1 255.255.255.255
Step 2 Configure R2 with a Loopback0 interface of 10.2.2.2 255.255.255.255
Step 3 Configure R3 with a Loopback0 interface of 10.3.3.3 255.255.255.255
Step 4 Copy all running-configs to the NVRAM and reload routers

Task 7: Verify OSPF Operation


Step 1 Use the show ip ospf neighbor command to verify information about other routers was learned
Step 2 Use the show ip protocols command to view information about the routing protocol

Task 8: Examine OSPF Routes in the Routing Tables

Step 1 Use the show ip route command to view all learned networks via OSPF

Task 9: Configure OSPF Cost


Step 1 Configure R1 serial interfaces with a bandwidth of 64
Step 2 Configure R1 serial interfaces with a bandwidth of 64
Step 3 Configure R1 serial interfaces with a cost of 1562

Task 10: Redistribute an OSPF Default Route

Step 1 Configure a loopback address on the R1 router to simulate a link to an ISP.


Step 2 Create the loopback 1 172.30.1.1 255.255.255.252 on the R1 router
Step 3 Create a Default route directing traffic to the loopback interface.
Step 4 Redistribute the default route using OSPF

Task 11: Verifying OSPF


Step 1 Using the show ip route command verify that the default route was learned.

You might also like