Scribd
Upload
37 views4 pages

EEE205L Exp 01-HardWare-Report

The document summarizes an experiment to study and plot the forward and reverse biased voltage and current characteristics of a semiconductor diode. The experiment used a DC voltage source, multimeter, breadboard, resistors, semiconductor diode, and jumper wires. Data was collected by varying the voltage from 0V to 1V in 0.1V increments and from 1V to 10V in 1V increments and recording the corresponding voltage and current values.

Uploaded by

abu talha priyonto
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
37 views4 pages

EEE205L Exp 01-HardWare-Report

The document summarizes an experiment to study and plot the forward and reverse biased voltage and current characteristics of a semiconductor diode. The experiment used a DC voltage source, multimeter, breadboard, resistors, semiconductor diode, and jumper wires. Data was collected by varying the voltage from 0V to 1V in 0.1V increments and from 1V to 10V in 1V increments and recording the corresponding voltage and current values.

Uploaded by

abu talha priyonto
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Brac University

Department of Electrical & Electronic Engineering


Summer 23
EEE205L
Electrical Circuits II Laboratory
Section: 01

Hardware Report

Experiment no. 01

Name of the experiment: Semiconductor Diode Characteristics

Prepared by:
Name: M A Mazed Anik ID: 22121064

Group Number: 02
Other Group members:
Sl. ID Name
1. 22121065 KM Rayhanul Islam
2. 22121069 MD MINHAZUL ISLAM RIFAT
3. 22121037 TASNIM MAHMUD ANIK
4. 22121039 Nadim Ahmed
5. 21221027 Bitto George Hembrom
Objectives:

The objective of the experiment is to study and plot the forward-reverse biased
semiconductor diodes voltage and current characteristics.

Equipment:
● DC voltage source
● Multi-meter
● Bread board
● Resistors: 1 KΩ
● Semiconductor
● Jumper wires

Circuit:

Vs  0V-1V @ 0.1V
1V-10V @ 1 V
Data:

Table:

R Vs VD VR IR=VR/R ID=IR
(KΩ) (V) (V) (V) (mA) (mA)
0 0 0 0 0
0.128 0.128 0 0 0
0.226 0.226 0 0 0
0.339 0.335 0.003 0.003 0.003
0.469 0.394 0.015 0.015 0.015
0.504 0.444 0.058 0.058 0.058
0601 0.476 0.122 0.123 0.123
0.7096 0.499 0.209 0.211 0.211
0.801 0.514 0.2847 0.288 0.288
0.925 0.529 0.391 0.396 0.396
0.986 1.044 0.540 0.491 0.497 0.497
2.08 0.59 1.47 1.49 1.49
3.04 0.61 2.42 2.454 2.454
4.04 0.63 3.42 3.468 3.468
5.00 0.64 4.31 4.371 4.371
6.05 0.65 5.38 5.456 5.456
7.04 0.66 6.41 6.501 6.501
8.03 0.67 7.24 7.342 7.342
9.03 0.67 8.33 8.448 8.448
10.1 0.68 9.4 9.533 9.533
Graph:

You might also like