Reference Guide

Fluids and Lubricating

Greases
Surface Drill Rigs

Original Instructions
2021-03-11 | No: TIS0003566.002 en-US
Fluids and Lubricating Greases Table of Contents

Table of Contents
1 Introduction ............................................................................................................ 5
1.1 Safety First ................................................................................................................................ 5
1.2 The Purpose of This Guide ...................................................................................................... 5
1.3 Target Group ............................................................................................................................. 5
1.4 General Recommendations for Fluids and Lubricating Greases ......................................... 5
1.5 Temperature Zones................................................................................................................... 5

2 Applicable Models ................................................................................................. 7

3 Fluids and Lubricating Greases ........................................................................... 9

3.1 Hydraulic Oil .............................................................................................................................. 9
3.2 Compressor Oil ......................................................................................................................... 9
3.2.1 Top Hammer and COPROD Machines, Single-Stage Compressor ..................................... 10
3.2.2 DTH Machines, Two-Stage Compressor.............................................................................. 10
3.3 Fuel........................................................................................................................................... 10
3.4 Engine Oil ................................................................................................................................ 11
3.5 Diesel Exhaust Fluid ............................................................................................................... 11
3.6 Engine Coolant........................................................................................................................ 12
3.7 Lubrication Oil Tank (ECL) (HECL) (ECG) ............................................................................ 12
3.8 Rock Drill Grease for Top Hammer and COPROD ............................................................... 13
3.9 Rotation Unit Grease for Down-The-Hole (DTH) .................................................................. 13
3.10 Grease Nipples and Central Lubrication System (CLS) ...................................................... 13
3.11 Spray Grease for Thread Lubrication with Brushes ............................................................ 13
3.12 Air Conditioning Refrigerant.................................................................................................. 13
3.13 Traction Gear Oil ..................................................................................................................... 14
3.14 Contact Grease ....................................................................................................................... 14
3.15 Oil for Service Winch .............................................................................................................. 14
3.16 Oil for Tramming Winch ......................................................................................................... 14

iii No: TIS0003566.002 en-US

Fluids and Lubricating Greases Table of Contents

iv No: TIS0003566.002 en-US

Fluids and Lubricating Greases 1 Introduction

1 Introduction

1.1 Safety First

Always read the information in the safety manual before starting to use the machine or be-
fore starting any maintenance work.

1.2 The Purpose of This Guide

The Fluids and Lubricating Greases Reference guide is intended to:
• Provide information on the machine-specific fluid and grease types used at the Epiroc
Örebro factory
• Provide information on the specifications and standards of the fluids and greases
This guide does not replace the necessary training that is required for handling machines
and related equipment.

1.3 Target Group

The information in this publication is intended for everyone involved in the application, op-
eration, and maintenance of the machine and related equipment. All readers are expected
to possess basic competence regarding mining methods, construction methods, and the
machines used for construction and mining operation.

1.4 General Recommendations for Fluids and Lubricating

Greases
All fluids and greases are essential to preventive maintenance. It is important to follow the
instructions in the machine-specific operation and maintenance manuals.
• Select the correct quality and viscosity grade of fluids and greases to improve the effi-
ciency and extend the service life of components.
• Use fluids and greases that meet or exceed the requirement specifications.
• Read the Safety Data Sheet (SDS) before using the fluid or grease and take needed
measures for safe handling.
• Never mix fluids and greases of a different type or grade.
• Contact the Original Equipment Manufacturer (OEM) or refer to the OEM manuals for
more information, if necessary.
• Dispose of used fluids and greases in accordance with local environmental regula-
tions.
• Due to regional availability, operating conditions, and continual development, specific
brands and types of fluids and greases in this manual are not applicable to all situa-
tions.
• Contact the local Epiroc representative for questions related to fluids and greases.

1.5 Temperature Zones

All fluids pertain to an intended temperature zone.

5 No: TIS0003566.002 en-US

Fluids and Lubricating Greases 1 Introduction

Temperature Zone Temperature Range (°C) Temperature Range (°F)

Arctic, -40 °C option, for DTH -45 − 0 -49 − 32

machines

Arctic -30 − 0 -22 − 32

Normal -10 − 30 14 − 86

Tropical 20 − 60 68 − 140

6 No: TIS0003566.002 en-US

Fluids and Lubricating Greases 2 Applicable Models

2 Applicable Models

Fluids and greases information for the following machine models are included in this refer-
ence guide:

Surface Drill Rigs COPROD SmartROC C50

SmartROC CL

Top hammer PowerROC T30 E

FlexiROC T15 R
FlexiROC T30 R
FlexiROC T35
FlexiROC T35 R
FlexiROC T40
FlexiROC T40 R
FlexiROC T45
SmartROC T35
SmartROC T40
SmartROC T45

Down-The-Hole (DTH) FlexiROC D50

FlexiROC D55
FlexiROC D60
FlexiROC D65
SmartROC D50
SmartROC D55
SmartROC D60
SmartROC D65

7 No: TIS0003566.002 en-US

Fluids and Lubricating Greases 2 Applicable Models

8 No: TIS0003566.002 en-US

Fluids and Lubricating Greases 3 Fluids and Lubricating Greases

3 Fluids and Lubricating Greases

3.1 Hydraulic Oil

The oil serves as the power transmission medium, system coolant, and lubricant for the hy-
draulic system. The quality of hydraulic oil is important to the satisfactory performance of
the hydraulic system.

! NOTE: Use the suitable hydraulic oil for the specific ambient temperature.

NOTE: Surplus oil must be disposed of in an environmentally friendly manner as pre-

! scribed by local authorities.

Machine Temperature Zone Oil Used at Factory Specification

All applicable models Standard Tellus S2V 46 ISO VG: 46 / VI: 143

Tropical option Tellus S2V 68 ISO VG: 68 / VI: 142

Arctic option Tellus S2V 32 ISO VG: 32 / VI: 143

FlexiROC D50 Arctic, - 40 °C option Tellus S4VX 32 ISO VG: 32 / VI: 300
FlexiROC D55
FlexiROC D60
FlexiROC D65
SmartROC D50
SmartROC D55
SmartROC D60
SmartROC D65

Use a mineral-based or synthetic (polyalphaolefin or diester) hydraulic oil that contains in-
hibiting properties for rust, wear, oxidation, and foam as well as having air and water sepa-
ration ability. Select an oil with a Viscosity Grade (VG) and a Viscosity Index (VI) that is ap-
plicable for the intended temperature zone. An oil with a high viscosity index is less tem-
perature dependent.

3.2 Compressor Oil

Compressor oil is critical for reliability and reduces the operating costs throughout the life-
time of the compressor.

NOTE: Epiroc recommends only using EPIROC compressor oil for the single-stage and
! two-stage compressors. Use of another oil is at the customer's own risk.

9 No: TIS0003566.002 en-US

Fluids and Lubricating Greases 3 Fluids and Lubricating Greases

! NOTE: Never mix oils of different brands.

3.2.1 Top Hammer and COPROD Machines, Single-Stage Compressor

Machine Ambient Temperature C° (F°) Type Specification

PowerROC T30 E Below -10 (14) and above 30 (86) Compressor S VG: 46 / VI: 133
FlexiROC T15 R -10 to +30 (14–86) Compressor M VG: 46 / VI: 108
FlexiROC T30 R
FlexiROC T35 R
FlexiROC T35
FlexiROC T40 R
FlexiROC T40
FlexiROC T45
SmartROC T35
SmartROC T40
SmartROC T45
SmartROC C50
SmartROC CL

3.2.2 DTH Machines, Two-Stage Compressor

NOTE: If the ambient temperature permits, Compressor S xtreme should be used in

! the first instance.

Machine Ambient Temperature C° (F°) Type Specification

FlexiROC D50 Below -10 (14) Compressor S VG: 46 / VI: 133

FlexiROC D55 Above -10 (14) Compressor S VG: 68 / VI: 119
FlexiROC D60 xtreme
FlexiROC D65
SmartROC D50
SmartROC D55
SmartROC D60
SmartROC D65

3.3 Fuel
The quality of the diesel fuel is an important factor for the performance, the lifetime, and
the emission levels of the diesel engine.

10 No: TIS0003566.002 en-US

Fluids and Lubricating Greases 3 Fluids and Lubricating Greases

NOTE: Use only diesel fuel that meets the requirements in the engine operation and
! maintenance manual.

NOTE: Stored fuel must be stored in a closed container that prevents contact with the
! air. The container must be clean and approved for the storage of fuel.

Diesel Engine Emission Specification Type

Standard

Stage V (EU) Must meet cleanliness ISO 4406 Ultra-low sulfur diesel (ULSD <15
Tier 4 Final (US) rating 18/16/13 or better. ppm).

Stage IIIA (EU) Must meet cleanliness ISO 4406 Low-sulfur diesel (LSD <500
Tier 3 (US) rating 18/16/13 or better. ppm).

3.4 Engine Oil

NOTE: Use only engine oil that meets the requirements in the engine operation and
! maintenance manual.

Diesel Engine Emission Ambient Temperature C° (F°) Specification Type

Standard
Minimum Maximum

Stage V (EU) -9.5 (14.9) 50 (122) API: CJ-4 15W-40

Tier 4 Final (US) -18 (0) 50 (122) 10W-40

-30 (-22) 50 (122) 5W-40

Diesel Engine Emission Ambient Temperature C° (F°) Specification Type

Standard
Minimum Maximum

Stage IIIA (EU) -9.5 (14.9) 50 (122) API: CI-4, CI-4+ 15W-40
Tier 3 (US) -18 (0) 50 (122) 10W-40

-30 (-22) 50 (122) 5W-40

3.5 Diesel Exhaust Fluid

NOTE: Consult the Original Equipment Manufacturer (OEM) for the Diesel Exhaust
! Fluid (DEF) specifications.

NOTE: Do not add water to DEF. Store DEF in a cool, dry, and well-ventilated area.
! Avoid storing the DEF in the sun. Optimum storage temperature is between -11 °C
(12 °F) and 30 °C (86 °F).

11 No: TIS0003566.002 en-US

Fluids and Lubricating Greases 3 Fluids and Lubricating Greases

Diesel Engine Emission Stan- Type Specification

dard

Stage V (EU) Ad blue ISO 22241

Tier 4 Final (US) The DEF must fulfill the require-
ments specified in ISO 22241-1,
DIN 70070, or ASTM D7821.

3.6 Engine Coolant

NOTE: Use only ready mixed Organic Acid Technology (OAT) coolant that meets
! ASTM D6210.

NOTE: Consult engine manufacturer's local representative for coolant requirement and
! maintenance.

! NOTE: Do not use sealing additives or soluble oils in the cooling system.

Machine Coolant Used at Factory Concentration

All applicable models Univar 774F Concentration 50/50 (-37).

3.7 Lubrication Oil Tank (ECL) (HECL) (ECG)

• Electric Controlled Lubrication (ECL) - Lubrication system for rock drill
• Hammer Electric Controlled Lubrication (HECL) - Lubrication system for COPROD and
rotation unit
• Electric Controlled Greasing (ECG) - Thread lubrication system (optional equipment).
ECG uses COP oil from the lubrication oil tank.

NOTE: Epiroc recommends using Epiroc COP oil which is specially developed for hy-
! draulic rock drills and rotation units.

COP oil is an environmentally friendly and degradable oil.

Ambient Temperature C° (F°) Type Viscosity Grade

Minimum Maximum

COP Rock drill -25 (-13) 50 (122) Epiroc COP oil ISO VG 100

DHR Rotation unit -25 (-13) 50 (122) Epiroc COP oil ISO VG 100

NOTE: If COP oil is not available, see the oil specification in the maintenance manual
! for the COP rock drill or the DHR rotation unit.

12 No: TIS0003566.002 en-US

Fluids and Lubricating Greases 3 Fluids and Lubricating Greases

3.8 Rock Drill Grease for Top Hammer and COPROD

NOTE: Epiroc recommends using Epiroc COP grease, which has been specially devel-
! oped for Epiroc hydraulic rock drills, and is suitable for gear housing and flushing seals.
COP grease is adequate for both arctic and tropical conditions.

Ambient Temperature °C (°F) Type

Minimum Maximum

COP Rock drill -40 (-40) 150 (302), up to 220 (428) for Epiroc COP grease
shorter periods

NOTE: If COP grease is not available, see the grease specification in the maintenance
! manual for the COP rock drill.

3.9 Rotation Unit Grease for Down-The-Hole (DTH)

NOTE: See the grease specification in the maintenance manual for the DHR rotation
! unit.

3.10 Grease Nipples and Central Lubrication System (CLS)

Machine Ambient Temperature °C (°F) Type Specification

Minimum Maximum

All applicable -25 (-13) 110 (230) Shell Gadus S3 A1300 C NLGI 2
models 2 (SRS 4000)

3.11 Spray Grease for Thread Lubrication with Brushes

Machine Ambient Temperature °C (°F) Type Specification

Minimum Maximum

All applicable -25 (-13) 110 (230) Shell Gadus S3 A1300 C NLGI 2
models 2 (SRS 4000)

3.12 Air Conditioning Refrigerant

Machine Specification

Applicable models with cab R134a

13 No: TIS0003566.002 en-US

Fluids and Lubricating Greases 3 Fluids and Lubricating Greases

3.13 Traction Gear Oil

Machine Ambient Temperature °C (°F) Type Specification

Minimum Maximum

All applicable Shell Omala S4 G 220 ISO VG 220

models
Mobil SHC Gear 220

3.14 Contact Grease

Component Specification

Electrical contacts Contact grease that is fortified with a high level of

• Contact grease must not be used on sealed rust, corrosion, and oxidation inhibitors.
watertight connectors. NLGI Number: 1–2
• Contact grease must be used on open con- Drop Point: 200 °C (392 °F)
nectors.
Operating Temperature: -40 °C to 130 °C (-40 °F
to 266 °F)

3.15 Oil for Service Winch

NOTE: See the sign on the service winch for information from the Original Equipment
! Manufacturer (OEM).

! NOTE: Consult the OEM for oil specification.

3.16 Oil for Tramming Winch

NOTE: See the sign on the winch for information from the Original Equipment Manufac-
! turer (OEM).

! NOTE: Consult the OEM for oil specification.

14 No: TIS0003566.002 en-US

Fluids and Lubricating Greases 3 Fluids and Lubricating Greases

15 No: TIS0003566.002 en-US

 2021-03-11 | No: TIS0003566.002 en-US

epiroc.com