Scribd
Upload
10 views

5 Assembly

The document provides step-by-step instructions for disassembling and reassembling the major components of a printer, including the cover assembly, LED panel, laser scanning unit, transfer roller, motor assembly, HVPS board, fuser assembly, thermostat and halogen lamp, SMPS board, and main board and sensor board. Disassembly must be done in a specific order, and reassembly follows the reverse steps.

Uploaded by

rodrigoapazamorales
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
10 views

5 Assembly

The document provides step-by-step instructions for disassembling and reassembling the major components of a printer, including the cover assembly, LED panel, laser scanning unit, transfer roller, motor assembly, HVPS board, fuser assembly, thermostat and halogen lamp, SMPS board, and main board and sensor board. Disassembly must be done in a specific order, and reassembly follows the reverse steps.

Uploaded by

rodrigoapazamorales
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

Disassembly and Reassembly

3. Disassembly and Reassembly

3-1 Cover Assembly

3-1-1 Front Cover

1. Pull the both side of the cover to open. 4. Remove a screw of the front cover PCB and remove
the connector, then remove the cover.

2. Remove a screw and remove the stopper that holds


the printer cover.

3-1-2 Other Covers

1. Before you remove other covers, you should remove the


Front cover in advance.
2. Rear Cover : Remove the cover in the direction of a .
3. Top Cover : Remove the cover in the direction of b .
4. Side Cover L, R : Remove the cover in the direction of c .

3. Loosen the right lower part of the cover, then push the
cover in the direction of arrow to loosen the left lower
part.

3-1
Disassembly and Reassembly

3-2 LED Panel PBA


1. Before you remove other covers, you should remove. 3. Remove two screws, and remove LED panel.
• Front Cover (see [3-1 Main Cover])

2. Remove two screws of PCB cover, and widen the


hooks( a b c ) to remove.

4. Remove PCB from the PCB cover.

3-3 LSU(Laser Scanning Unit)


1. Before you remove LSU, you should remove front 3. Remove two connectors from the LSU, then remove
cover, rear cover and top cover. the LSU.
• Main Cover (see [3-1 Main Cover])

2. Remove three screws securing the LSU.

3-2
Disassembly and Reassembly

3-4 Transfer Roller


1. Open the front cover.

2. Use a proper tool("-" type screwdriver) to pull the one


end of the roller slightly, then take it out.

3-5 Motor Assembly


1. Before you remove the motor assembly, you should
remove:
• Main Cover (see [3-1 Main Cover])
• Shield Engine Assembly

2. Remove five screws securing the motor assembly


and remove a connector from engine board(Engine
board and SMPS board are integrated), then take the
motor assembly out.

3-3
Disassembly and Reassembly

3-6 HVPS Board

1. Before you remove HVPS board, you should remove:


•Main Cover (see [3-1 Main Cover])

2. Remove four screws and a connector from HVPS


board, then take the board out.

When you reassemble the HVPS board, make


Note sure that five terminals should be put in place.
Terminal

3-7 Fuser Assembly

1. Before remove fuser assembly, you should remove: 3. Remove two screws and unplug a fuser assembly
harness. Then use a " - " screwdriver to unlatch the
• Main Cover (see [3-1 Main Cover])
fuser assembly to remove.

2. Remove two ground screws and a connector as illus-


trated.

3-4
Disassembly and Reassembly

3-8 Thermostat and Halogen Lamp


1. Remove a screw from the fuser assembly and 3. Take the halogen lamp out from the Heat Roller.
remove the thermostat cover, then remove two
screws securing the thermostat.

When you reassemble the halogen lamp,


Note handle it with care as it is fragile.

2. Remove two screws from the fuser assembly, and


take the Heat Roller out.

3-5
Disassembly and Reassembly

3-9 SMPS Board


1. Before you remove the SMPS board, you should 3. Unplug connectors from the main board and connec-
remove: tors from SMPS, then remove the SMPS. Remove
four screws from SMPS and remove the SMPS
• Main Cover (see [3-1 Main Cover])
board.

2. Remove screws in the order of a b then remove


the shield engine assembly.

The Engine board and SMPS board are


Note integrated in a body.

3-6
Disassembly and Reassembly

3-10 Main Board and Sensor Board


1. Before you remove the main board, you should 3. Release four snap-fits securing the insulator engine
remove: board and then remove the insulator.
• Main Cover (see [3-1 Main Cover])
• SMPS board (see [3-9 SMPS Board])

2. Remove two screws from the main board and unplug


all of connectors, then remove the board.

Main B d

4. Release four snap-fits securing the sensor board and


then remove the sensor board.

3-7

You might also like