Scribd
Upload
153 views1 page

EC100R DataSheet

The document discusses reflective beam smoke detectors, including their overview, standard features, applications, technical specifications, and ordering information. The detectors comprise a transmitter and receiver in a single enclosure to detect smoke by analyzing the attenuation of an infrared light beam reflected between the units.

Uploaded by

Esteban Andres Méndez Ávila
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
153 views1 page

EC100R DataSheet

The document discusses reflective beam smoke detectors, including their overview, standard features, applications, technical specifications, and ordering information. The detectors comprise a transmitter and receiver in a single enclosure to detect smoke by analyzing the attenuation of an infrared light beam reflected between the units.

Uploaded by

Esteban Andres Méndez Ávila
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Input devices

Overview Standard Features


The EC-50R/-100R comprises a transmitter and receiver in a • Coverage:
single enclosure and is usually installed between 19 inches and — 50R range 15 -160 ft (4.6 - 48.8m);
24 inches below the ceiling. The transmitter emits an invisible — 100R range 160- 330 ft (48.8 - 100m)
infrared light beam that is reflected via a prism mounted directly • Microprocessor controlled
opposite and with a clear line of sight. The reflected infrared light • Automatic drift compensation
is detected by the receiver and analyzed. Smoke in the beam • Selectable alarm thresholds
path will reduce the received infrared light proportionally to the • 24 Vdc operating voltage
density of the smoke. The detector analyzes this attenuation or • Optional Ground Level Test Station
obscuration of light and acts accordingly. Detectors are typically
mounted within ±30 feet (9.14 m) of a potential fire source. Consult Application
your Authority Having Jurisdiction for spacing requirements Reflective beam smoke detectors are ideal for large open areas
specific to your locality. such as warehouses, hotel atriums, industrial plants and school
gymnasiums.
Technical Specifications
Beam Detector
Installation and Mounting
The recommended installation height is approximately 19 to
Power Supply 10.2 Vdc to 30 Vdc (continuous power)
24 inches (483 to 610 mm) below the ceiling. However, in all
Standby: Less than 4 mA
Current
Alarm/Trouble: Less than 14 mA
installations the National Fire Standards for that country/state
must be consulted.
Alarm: Normally Open, rated 2A, 30 Vdc,
resistive Because of the reflecting properties of the beam, all objects must
Contacts
Trouble: Normally Closed, rated 2A, 30 Vdc, be kept a minimum of 19 inches (483 mm) away from the centre
resistive of the beam path down the entire beam length. If highly reflective
Signal Delay Alarm and trouble: 10 seconds surfaces are close to the beam, then greater clearances should be
Reset Time >5 seconds (power down) applied.
Dimensions (HxWxD) 8.25 in x 5.1 in x 4.7 in (21 cm x 13 cm x 12 cm)
Weight 1.5 lb (0.68 kg) Ordering Information
Operating Temperature: 32°F to 100°F (0°C to 37°C)
Ship Wt
Environment Humidity: 93% RH, Non-condensing Cat. No. Description
lb (kg)
Width: 30 ft (9.14 m) either side of beam
EC-50R Reflective Beam Smoke Detector
Length (EC-50R): 15 ft to 160 ft EC-50R 2.0 (0.90)
c/w test filter and one reflector
Beam Coverage (4.57m to 48.77m)
Length (EC-100R): 160 ft to 330 ft EC-100R Reflective Beam Smoke Detector
EC-100R 2.0 (0.90)
(48.77m to 100m) c/w test filter and four reflectors
2.50dB (25%), 3.74dB (35%),
Alarm Thresholds
6.02dB (50%) obscuration

Reflective Beam Smoke


Detector
EC-50R/-100R

EC-50R

21
© 2007 General Electric Company. All Rights Reserved.

You might also like