Scribd
Upload
81 views2 pages

F5-Welding Procedure Specification

The document provides a welding procedure specification for miscellaneous mechanical works at an IREP unit area. It details the project name, client, consultant, company name, welding process type, applicable piping class, joint design, base metals, filler metals, positions, preheat and post weld heat treatment requirements, gases used, electrical characteristics, welding technique, and filler metal, current, voltage and travel speed parameters.

Uploaded by

veera Satya sai
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
81 views2 pages

F5-Welding Procedure Specification

The document provides a welding procedure specification for miscellaneous mechanical works at an IREP unit area. It details the project name, client, consultant, company name, welding process type, applicable piping class, joint design, base metals, filler metals, positions, preheat and post weld heat treatment requirements, gases used, electrical characteristics, welding technique, and filler metal, current, voltage and travel speed parameters.

Uploaded by

veera Satya sai
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 2

WELDING PROCEDURE SPECIFICATION

(QW-482 AS PER SECTION IX)

Project Name : MISCELLANEOUS MECHANICAL WORKS (IREP UNIT AREA)


Client : BHARAT PETROLEUM CORPORATION LIMITED, KOCHI
Consultant : ENGINEERS INDIA LIMITED

Company Name : SATNAM GLOBAL INFRAPROJECTS LIMITED

Welding Procedure Specification No. : SGIL/A307/ WPS/MMW Rev. 0 Date :

Supporting PQR No(s) : SGIL/ – Rev.0

Welding Process(es) : Type :

Applicable piping class :

Joint Design (QW402) :


Backing (Yes/No) :
Backing Material (Type) :

BASE METALS (QW-403)


P. NO. : GR. NO. : TO P. NO. : GR. NO. :

Specification Type & Grade :


to
Specification Type & Grade :

Chem.. Analysis to Mech. Prop.

to chem.. Analysis to Mech. Prop. :

Base metal : Groove : Fillet :

Pipe Dia. Range : Fillet :

Other :

FILLET METALS (QW404)


Spec. No. (SFA) :
AWS NO. (CLASS) :
F.NO. :
A.NO. :
Size of Filler Metals :

Weld Metal Thickness Range:


Groove :
Fillet :
Electrode - Flux (Class ) :
Flux Trade Name :
Consumable Insert :
Each base metal /filler metal combination should be recorded individually.

Contd..2.

..2..
POSITIONS (QW405)

Position (s) of groove :


Welding Progression :

PRE HEAT (QW406)


Preheat Temperature :
Inter -pass Temperature :
Preheat Maintenance :

POST WELD HEAT (QW407) GAS (408)


Temperature Range : Shielding Gas(es) :
Time Range : Percentage Composition :
Rate of heating : Flow Rate :
Rate of Cooling : Gas Backing :
Holding Time : Trailing Shielding Gas :
Composition :

ELECTRICAL CHARACTERISTICS (QW 409)


Current AC or DC : Polarity :

Amps (Range) : Voltage :


Tungsten electrode size and type :
Mode of metal transfer for GMAW :
Electrode wire feed speed range :

TECHNIQUE (QW410)
Stringer or Weave Bead :
Orifice or Gas Cup Size :
Initial & inter pass cleaning (Brushing, Grinding etc,) :
Method of back gouging :
Oscillation :
Multiple or Single Pass (per side ) :
Multiple or Single Electrode :
Travel Speed (Range) :
Peening :
Other :

FILLER METAL CURENT TRAVEL


WELD AMP VOLTS SPEED
PROCESS TYPE REMARKS
LAYER (S) CLASS DIA RANGE RANGE RANGE
POLAR
(A) (V) (MM/ MIN)
1
2
3
4

SGIL EIL

You might also like