Dodge Cummins User Guide

Cindy Myers
Dodge Cummins User Guide
© 1998 EFILive Limited
All rights reserved

First published
14 February 2011

Revised
5 October 2021

EFILive, EFILive FlashScan and EFILive AutoCal are registered trademarks of EFILive Limited.
All other trademarks belong to their respective owners.
 Dodge Cummins User Guide

Contents

............................................................................................................5
Prerequisites ....................................................................................................................5
Intended Audience .......................................................................................................5
Computer Knowledge ...................................................................................................5
Tuning Knowledge .......................................................................................................5

......................................................................................................6
Introduction ......................................................................................................................6
What is EFILive? ..........................................................................................................6
Software Version Overview ..........................................................................................6
V8 Software Support ................................................................................................6
V7 Software Support ................................................................................................7
CSP5 Cummins Switchable Programming ....................................................................7
EDA Data Logging .......................................................................................................7
RSA Digital Signature ..................................................................................................7
Security Gateway Module ............................................................................................8

...............................................................................................................9
Finding the Correct Base File ..........................................................................................9
ECM Label Identification ..............................................................................................9
V8 Scan and Tune .....................................................................................................10
FlashScan/AutoCal V3 ...............................................................................................10
Option 1: Display VIN/Info ......................................................................................10
Option 2: Record All Diagnostics ............................................................................11
FlashScan V2 .............................................................................................................11
Option 1: Display VIN/Info ......................................................................................11

[email protected] -1- www.efilive.com

 Dodge Cummins User Guide
Option 2: Record All Diagnostics ............................................................................11
AutoCal V2 .................................................................................................................11
Option 1: Display VIN/Info ......................................................................................11
Option 2: Record All Diagnositcs ............................................................................12
Match Calibration Requirements ................................................................................12

..........................................................................................................13
Licensing Requirements ................................................................................................13
Dodge Cummins Tuning Option Enabled ...................................................................13
VIN Licensing .........................................................................................................13

..........................................................................................................15
V8 Scan and Tune Scan ................................................................................................15
Pass-Thru Data Logging ............................................................................................15
Pass-Thru Read a Controller (CMB and CMC only) ...................................................16
Edit a Tune File ..........................................................................................................18
Cummins Fuel Timing Calculator............................................................................19
Pass-Thru Licence and Flash a Controller .................................................................21
Move Tune and Log files from FlashScan/AutoCal to your PC ..................................22
FlashScan/AutoCal V3 ...........................................................................................22
FlashScan/AutoCal V2 ...........................................................................................23

..........................................................................................................24
Configure FlashScan/AutoCal for BBX ..........................................................................24
EDA Data Logging .....................................................................................................24
Configure Tuning........................................................................................................25
Tune File Switching ....................................................................................................25
Configure DTCs .........................................................................................................25

[email protected] -2- www.efilive.com

 Dodge Cummins User Guide
Quick Setup ...............................................................................................................25

.............................................................................................................27
FlashScan/AutoCal Menu Navigation ............................................................................27
FlashScan/AutoCal V3 ...............................................................................................27
Data Logging ..........................................................................................................27
Read a Controller (CMB and CMC only) ................................................................27
License and Flash a Controller ...............................................................................28
Switch Tunes using FlashScan/AutoCal V3 ...........................................................28
FlashScan V2 .............................................................................................................29
Data Logging ..........................................................................................................29
Read a Controller (CMB and CMC only) ................................................................29
License and Flash a Controller ...............................................................................29
Switch Tunes using FlashScan V2 .........................................................................30
AutoCal V2 .................................................................................................................31
Data Logging ..........................................................................................................31
Read a Controller (CMB and CMC only) ................................................................31
License and Flash a Controller ...............................................................................32
Switch Tunes using AutoCal V2 .............................................................................32

.............................................................................................................33
Support ..........................................................................................................................33
Trouble Shooting ........................................................................................................33
Error Codes ................................................................................................................33
Checksums ................................................................................................................33
Dodge Cummins Fast CAN Mode – CMD, CME, CMF ..............................................34
Cummins 5.9L ECM VIN Issues .................................................................................34
Failed Flash Recovery Methods .................................................................................34
Flash Base with without tune file security restrictions. ............................................34
ROM Boot Recovery ...............................................................................................34
Test for Rogue Modules .............................................................................................35
Trace Files .................................................................................................................35
V8 Scan and Tune *.htx files ..................................................................................35
[email protected] -3- www.efilive.com
 Dodge Cummins User Guide
FlashScan/AutoCal V3 *.xalm files .........................................................................35
FlashScan V2 Trace Files ......................................................................................36
AutoCal V2 Trace Files ...........................................................................................36
Knowledgebase..........................................................................................................37
EFILive Authorized Dealer .........................................................................................37
How to Tune? .............................................................................................................37
EFILive Service Desk .................................................................................................37

[email protected] -4- www.efilive.com

 Dodge Cummins User Guide

Prerequisites

Intended Audience
EFILive Customers using the V8 Scan and Tune Tool software.

Computer Knowledge
It is expected that readers have a basic understanding of:
 The Windows operating system;
 Starting and using Windows applications;
 Navigating folders using Windows Explorer.

Tuning Knowledge
It is expected that readers have a basic understanding of:
 Electronic Fuel Injection;
On Board Diagnostics. And enough common sense to understand the following:
 Make small incremental changes;
 Only make minimal changes at a time;
 Evaluate and analyze the results of each change using the Scan Tool
and/or other data logging devices before making the next change;
 Do not make changes that you do not understand;
 If you are unsure about making a particular change, ask a knowledgeable
tuner first.

[email protected] -5- www.efilive.com

 Dodge Cummins User Guide

Introduction

What is EFILive?
EFILive is tuning software and hardware - it is not a tune. Together the software
and hardware give users the tools to write tunes. EFILive does not provide tune
files, tuning advice or support, but do provide software support and hardware
support.

Software Version Overview

This version of the Cummins Quick Start Guide migrates all processes to EFILive
V8 Scan and Tune software. Functionality is still available in V7.5 software,
however software support and bug fixes will cease in 2021.
FlashScan/AutoCal V3 and AutoCal V2 are not compatible with V7 software. V7
functions are only supported by FlashScan V2. The following is a brief view of the
activities that are performed with the different software versions:

V8 Software Support
The following Dodge Cummins are supported in the following ways in the V8 Scan
and Tune software:
V8 Software
Controller Engine Year
Scan OBD Read Flash Edit
CM2450B
(CMF) 6.7L 2019+
CM2350B
(CME) 6.7L 2013-2018
CM2200
(CMD) 6.7L 2010-2012
CM2100
(CMC) 6.7L 2007-2009
CM849
(CMB) 5.9L 2006-2007

[email protected] -6- www.efilive.com

 Dodge Cummins User Guide
V7 Software Support
The following Dodge Cummins are supported in the following ways in the V7 Tune
Tool and V7 Scan Tool software:
V7 Software
Controller Engine Year
Scan OBD Read Flash Edit
CM2450B
(CMF) 6.7L 2019+
CM2350B
(CME) 6.7L 2013-2018
CM2200
(CMD) 6.7L 2010-2012
CM2100
(CMC) 6.7L 2007-2009
CM849
(CMB) 5.9L 2006-2007
In 2010 Cummins implemented restrictive ECM architecture which prevents CMD,
CME and CMF ECMs from being read via the OBD-II Port.
Customers will need to obtain a suitable base file for editing and flashing. A
selection of EFILive compatible base stock files is readily available on the internet
or custom files may be purchased through organizations that have the necessary
hardware and software to create personalized base files.
Because you cannot read the existing tune in the ECM it is important you select
the correct base tune to suit your vehicle.

CSP5 Cummins Switchable Programming

EFILive's CSP custom operating systems for the Cummins ECMs allows
customers to be able to switch 'on the fly' between multiple tunes, all stored in the
ECM's flash memory.
Refer to the specific user guide for your controller for detailed instructions on how
to upgrade your operating system.

EDA Data Logging

EFILive’s Enhanced Data Logging (EDA) allows customers to log 45 individual
data parameters specifically chosen to complement tuning at up to 50 frames per
second during pass-thru logging and Black Box Logging (BBL) using
FlashScan/AutoCal V3 or FlashScan/AutoCal V2.
EDA is only accessible to customers who upgrade to EFILive’s CSP5 operating
system. Refer to the specific user guide for your controller for detailed instructions
on how to upgrade your operating system.
Limited factory logging is available on non-CSP operating systems

RSA Digital Signature

In early 2009 Cummins ECMs were manufactured with higher levels of security
consisting of an RSA Digital Signature on the calibrations. The RSA Digital
Signature does not prevent the flashing of stock tunes, it ONLY prevents the
[email protected] -7- www.efilive.com
 Dodge Cummins User Guide
flashing of modified tunes, so to flash a modified tune the Digital Signature must
be switched off.
The EFILive ECM flash process manages the removal of the Digital Signature via
OBD-II flashing in the following circumstances:
Controller Flash Method
CM2450B (CMF) In vehicle and bench harness flashing.
CM2350B (CME) In vehicle and bench harness flashing.
CM2200 (CMD) Bench unlocking only (due to TIPM).
CM2100 (CMC) Bench unlocking only (due to TIPM).
Not Applicable - RSA Digital Signature not
CM849 (CMB)
implemented.
In vehicle flashing for CM2100 and CM2200 controllers requires the BootRSA
Patch file process to remove the digital signature. Please refer to the Cummins
Boot RSA Patch User Guide.
NOTE: The ECM must be fully operational and not in boot mode as a result of a
failed flash (error $0340) or forced boot mode. Where the ECM is in boot mode,
the unlock process is bypassed and two-step flash process is required to remove
the digital signature.
1. Recover the ECM by flashing a stock tune to restore the ECM to
operational mode.
2. Flash the ECM to remove the digital signature.

Security Gateway Module

In 2018 Dodge implemented an additional anti-tuning security measure via the
security gateway module. Customers will need to bypass this module by installing
a Security Gateway Module bypass cable (SGM bypass cable).
The SGM bypass cable requires users to replace the two CAN wires in the factory
OBD-II port and connect the bypass cable into the large white connector just
above the OBD-II port in any of the available slots. This cable remains
permanently in the truck and does not need to be removed after flashing.
The OBD-II port will retain all normal functionality, and only bypasses the SGM to
allow flashing to the ECM.
Where the SGM module is detected and a bypass cable is not in place, the
following error will be displayed when the flash is aborted.
Aborting Flash: SGM Detected
Please: Wait...
Script exited with code $0333: Security Access Denied ($33).

[email protected] -8- www.efilive.com

 Dodge Cummins User Guide

Finding the Correct Base File

For controllers that support reading, EFILive recommends reading the vehicle’s
controller to obtain a suitable base file.
For controllers that do not support reading, the following instructions will help you
to determine the base tune file that should be used for editing.
Because you cannot read the existing tune in the ECM it is important you select
the correct base tune to suit your vehicle.
EFILive does not provide stock tunes or modified tunes. There are a variety of
stock tunes available on the internet. Custom stock tunes can be purchased
through organizations that have the necessary hardware and software to create
personalized base files.
There are a number of methods to find the calibration details of the tune presently
in the ECM. Customers can choose which method best suits their needs.

ECM Label Identification

Locate the label on the ECM and document the E/C part number.

In this example, D090072 refers to the calibration configuration and .04 refers to
the fourth revision.
Provide this information to your tuner for correct base file identification.
[email protected] -9- www.efilive.com
 Dodge Cummins User Guide
V8 Scan and Tune
1. Open the EFILive V8 Scan and Tune software.
2. Connect your FlashScan/AutoCal device to your PC and vehicle.
3. Turn the vehicle ignition to the On position.
4. Navigate to the [F4: OBD] -> [F2: OBD] menu option and select the [Details]
tab.
5. Select your controller(s) by using the [Auto Detect] button, or;
a. Hover over the Engine Controller box, and right click on the “Right-click to
select engine-controller” box and manually select the ECM.
b. Navigate and select the correct controller.

6. Click the [Read] button to populate controller data.

7. Copy or record the Calibration ID to use in the “Match Calibration
Requirements” step later in this document.

FlashScan/AutoCal V3
1. Connect your FlashScan/AutoCal V3 device to your vehicle.
2. Turn the vehicle ignition to the On position.

Option 1: Display VIN/Info

3. Navigate to the Diagnostics -> F1 Display Info -> F1: Display VIN Info menu
option.
4. Select correct controller type from list of controllers.

[email protected] - 10 - www.efilive.com
 Dodge Cummins User Guide
5. Copy or record the Calibration ID to use in the “Match Calibration
Requirements” step later in this document.

Option 2: Record All Diagnostics

3. Navigate to the Diagnostics -> F4 Record All Diags menu option.
4. FlashScan/AutoCal will display the file name that is saved onto the device.
5. Retrieve the text file by connecting FlashScan/AutoCal as a USB thumb drive.
6. Open the text file and view the calibration information using Windows notepad.

FlashScan V2
1. Configure FlashScan V2 for BBX features if not already setup.
2. Connect your FlashScan V2 device to your vehicle.
3. Turn the vehicle ignition to the On position.
4. Navigate to the F1: Scan Tool -> F1: Select PIDs menu option.
5. Select correct controller type from BBX configured controllers.
6. Return to the main menu.

Option 1: Display VIN/Info

7. Navigate to the F3: Diagnostics -> F1 Display Info -> F1: Display VIN Info
menu option.
8. Record the details displayed in the Cal: field to use in the match calibration
requirements step.

Option 2: Record All Diagnostics

7. Navigate to the F3: Diagnostics -> F4 Record All Diags menu option.
8. FlashScan will display the file name that is saved onto the device.
9. Retrieve the text file using EFILive Explorer. The file is stored in the scan
directory. The relevant file can then be transferred to PC
10. Open the text file and view the calibration information using Windows notepad.

AutoCal V2
1. Configure AutoCal V2 for BBX features if not already setup.
2. Connect your AutoCal V2 device to your vehicle.
3. Turn the vehicle ignition to the On position.
4. Navigate to [Scan Tool] -> [Select PIDs] menu
5. Select correct controller type from BBX configured controllers.
6. Return to the main menu.

Option 1: Display VIN/Info

7. Users can navigate to a range of options using the [Next] button. The
following options are available:
"Scan Tool"->"Display VIN"
"Scan Tool"->"Display OS"
"Scan Tool"->"Display SN"
"Scan Tool"->"Display Cal ID"
Where the display information exceeds 8 characters, a ">" character is
displayed at the end of the data prompting the user to press [Next] to scroll the
data horizontally. The "<" character indicates that the user can press the
[Prev] key to scroll the data back again.

[email protected] - 11 - www.efilive.com
 Dodge Cummins User Guide
8. Record the details displayed in the Cal ID: field to use in the match calibration
requirements step.

Option 2: Record All Diagnositcs

7. Navigate to the [Record Diags] menu to save the text file. AutoCal will display
the file name that is saved to the device.
8. Retrieve the text file using EFILive Explorer. The file is stored in the scan
directory. The relevant file can then be transferred to PC.
9. Open the text file and view the calibration information using Windows notepad.

Match Calibration Requirements

1. Using one of the identification methods above, either:
a. Provide the Cummins ECM Code (E/C) to your tuner for correct base
file identification; or
b. Match the calibration ID against the base *.ctz files.

2. Once you find a matching tune this can now become your base file should you
ever need to revert back to a stock tune.
For CMD, CME and CMF you cannot save the tune already installed in the
ECM, once you flash over it, it is gone forever, so choose your base tune
wisely.

[email protected] - 12 - www.efilive.com
 Dodge Cummins User Guide

Licensing Requirements

To Flash a Dodge Cummins ECM, the following licensing conditions must be met:
1. The Dodge Cummins Tuning Option must be enabled.
2. A VIN License must be available (if not already licensed).

Dodge Cummins Tuning Option Enabled

To ensure that your device is licensed to tune Dodge Cummins vehicles:
1. Connect your FlashScan or AutoCal device to your PC.
2. Open the EFILive Scan and Tune application.
3. Select the [F7: License] option in the left-hand pane.
4. Select [F2: Hardware] to display Tuning License details.

3. To purchase Tuning Options FlashScan, click on the Purchase Tuning

License Activation Code(s) link to order products. NOTE: The Cummins
Tuning Option is included on AutoCal devices, if this is not active, please
contact support.
4. Enter the activation code that was emailed to you and click the Activate button.

VIN Licensing
Each additional vehicle that you tune requires an available VIN license. The
license is allocated during the flashing process. Reflashing the same controller
multiple times using the same FlashScan/AutoCal uses the same license each
time.

[email protected] - 13 - www.efilive.com
 Dodge Cummins User Guide
To check that you have an available VIN license to allocate to your vehicle,
perform these steps.

1. Connect your FlashScan or AutoCal device to your PC.

2. Open the EFILive Scan and Tune application.
3. Select the [F7: License] option in the left-hand pane.
4. Select [F3: VINs] to display VIN License details.

5. To purchase additional VIN Licenses, click on the Purchase Activation Code(s)

link to order products. NOTE: AutoCal Users should contact their Tuner before
purchasing additional VIN licenses to manage the AutoCal’s maximum VIN
license capacity and tune file compatibility.
6. Paste the Activation Code and enter the License number from your email.

[email protected] - 14 - www.efilive.com
 Dodge Cummins User Guide

V8 Scan and Tune Scan

Pass-Thru Data Logging

To log data using FlashScan or AutoCal and V8 Scan and Tune software;
1. Open the EFILive V8 Scan and Tune.
2. Connect your FlashScan/AutoCal device to your PC and vehicle.
3. Turn the vehicle ignition to the On position.
4. Select an existing Dashboard configuration either by using the [Open Dash]
button or using the Dashboard drop down, or configure your own customized
dashboard after making controller and PID selections.
5. Navigate to the [F2: Scan] -> [F2: PIDs] menu option.
6. In the Engine field use the drop-down list to select the correct controller type or
use Auto Detect option.
7. Drag the selected PID from Available PIDs window into the Selected PIDs
window.

8. Navigate to the [F3: Data], [F4: Charts], [F5: Gauges] or [F6: Maps] tab and
configure your dashboard to customize data display formats.
9. Users should [Save Dash] to save their custom configurations to reduce future
configuration requirements.
10. Start the vehicle.
11. Select either Record or Monitor from the [F3: Data], [F4: Charts], [F5: Gauges]
or [F6: Maps] screens.
12. Select Stop to stop the data logging session.
13. Save the log.
14. To replay the data log, navigate to the [F3: Data], [F4: Charts], [F5: Gauges] or
[F6: Maps] tab and select the appropriate Playback buttons.

[email protected] - 15 - www.efilive.com
 Dodge Cummins User Guide

Important note for tuners:

If running a CSP5 tune and it does not seem to be switching as expected please
check the data in the "AIRDENSC_F" PID. For CSP5 to work correctly the
"AIRDENSC_F" PID must be in 'Normal Mode." If any other modes are active
(e.g. Protection Mode) then the ECM will not be using normal Altitude based
tables, and therefore will not using the CSP5 tables.
Protection Mode is a direct result of tuning strategy or DPF regen states.

Pass-Thru Read a Controller (CMB and CMC only)

Follow these steps to read the selected controller.
1. Connect your FlashScan/AutoCal device to your PC and vehicle.
2. Turn the vehicle ignition to the On position (vehicle must not be
cranked/running when reading).
3. Open the EFILive V8 Scan and Tune application.
4. Select the [F3: Tune] option in the left-hand pane.
5. On the [F2: Read] menu, select your controller(s) by using the [Auto Detect]
button, or;
1. Hover over the Engine Controller box, and right click on the “Right-click
to select engine-controller” box and manually select the ECM.
2. Navigate and select the correct controller.

[email protected] - 16 - www.efilive.com
 Dodge Cummins User Guide

6. Select the [Read] button to initiate the read operation.

7. While the ECM is reading an Elapsed time indicator, an Estimated Time

Remaining indicator, and a Progress bar will display tracking the Read
progress.
8. When the read process is complete a countdown timer will be shown. When
prompted perform the following actions:
1. Turn the vehicle ignition off.
2. Click on the Start Countdown button to begin the countdown timer.
3. DO NOT turn the vehicle ignition on until the countdown timer expires.
This time is critical to allow the ECM to perform internal, initialization
functions after a read or flash operation.

9. On the [F3: Calibration] tab, confirm Checksums are valid. Where the
checksums are invalid, users should not use the file and should source a
calibration file where checksums are valid.
10. If checksums are valid, save tune file. If this is your vehicle's stock calibration,
you should ensure you make a backup of this file in case you ever need to
return the vehicle to stock.

[email protected] - 17 - www.efilive.com
 Dodge Cummins User Guide
Edit a Tune File
Follow these steps to modify your ECM calibration.
1. Open the EFILive V8 Scan and Tune application.
2. Navigate to the [F3: Tune] -> [F5: Edit] menu in the left-hand pane.
3. Open your selected tune file.
4. On the [F3: Calibration] tab, confirm Checksums are valid. Where the
checksums are invalid, users should not use the file and should source a
calibration file where checksums are valid.
5. Navigate to the table(s) you wish to modify by using the Windows Explorer style
navigation window.
6. Highlight a cell, multiple cells, columns, rows or the entire table and adjust the
values using the calibrator editor icons.

7. A range of tune file security options can be applied using the options in the
[F3: Tune] -> [F4: Properties] -> Security Restrictions tab.

[email protected] - 18 - www.efilive.com
 Dodge Cummins User Guide
8. Save changes to the tune file by using the Save tuning file, Save tuning file as,
or Save tuning file for AutoCal options.
If using the Save option, ensure you have a copy of your stock tune saved
elsewhere.
Save tuning file as, and Save tuning file for AutoCal options automatically
appends a sequence number to the filename to make it unique giving users a
history of sequentially numbered files with each saved change made. A
FlashScan device must be connected to save security and/or AutoCal options.

Cummins Fuel Timing Calculator

To open the CFTC, click this icon in the tool bar:

The icon is only enabled when one of the fuel timing tables is displayed for editing.
When you open the CFTC window, the table is pre-populated with the correct
percentages that are required to calculate the currently displayed timing table
values. That allows you to evaluate the existing injection pulse timing. After you
have made any changes to the CFTC table, click the [Apply] button. Applying the
changes will update the underlying fuel timing table so that the injection pulses are
delivered at the timing selected in the CFTC window.
Minimum %
It is sometimes required that the minimum timing does not fall below a certain
percentage. In that case, check the Minimum % check box in the lower left corner
of the calculator window. And set the minimum percentage value.
Setting that value will not change any values displayed in the timing calculator,
instead it will simply force the calculator to compute timing values that are never
less than the percentage value specified when the [Apply] button is clicked.
For example, setting the Minimum % to 5 will force the calculator to treat all cells’
values that are less than 5% as if they were 5% when computing the fuel timing.

How does it work

When fuel is injected, the injection pulse width is some number of micro seconds.
Some tuners would like to set the fuel timing so that the injection pulse will start at
a given crankshaft position relative to top dead center (TDC) of the piston.
The CFTC allows you to specify the percentage of the injection pulse width that
will occur before top dead center (positive values), exactly at top dead center (0)
or after top dead center (negative values).
For example, assuming the injection pulse width for a particular cell is calibrated at
500us (500 micro seconds), then the following percentages in the fuel timing
calculator will result in the injection pulse starting at various crank shaft degrees
for 1000rpm and 2000 rpm:

[email protected] - 19 - www.efilive.com
 Dodge Cummins User Guide
Fuel Timing Injection Start Degrees Degrees Relative to TDC
% us @1000rpm @2000rpm
200% 1000 6.0 12.0 Before TDC
100% 500 3.0 6.0 Before TDC
50% 250 1.5 3.0 Before TDC
0 0 0.0 0.0 At TDC
-50% -250 -1.5 -3.0 After TDC
-100% -500 -3.0 -6.0 After TDC
-200% -1000 -6.0 -12.0 After TDC
Looking at the second row, a percentage of 100% means that the injection pulse
starts 100% of the pulse width before TDC. Since the pulse width is 500us, the
injection start time should be 500us (100% of 500us) before TDC. At 1000rpm that
would be 6 degrees before TDC, at 2000rpm that would be at 12 degrees before
TDC.
Looking at the fifth row, a percentage of -50% means that the injection pulse starts
50% of the pulse width after TDC. Since the pulse width is 500us, the injection
start time should be 250us (50% of 500us) after TDC. At 1000rpm that would be 3
degrees after TDC, at 2000rpm that would be at 6 degrees after TDC.
Related Tables
The CFTC uses values from two other related tables. Those tables will usually be
different for each timing table. The names of the related tables are shown in the
CFTC window’s description pane. If the values in those related tables are not
accurate then the calculator may not produce accurate results. For example, if you
were working with the timing table E2503, the related tables are: {D0508}
"Injection Pulse Conversion" and {D0782} "Fuel Pressure, Base". The first column
of data in {D0508} may be calibrated to be all zeros which will cause this calculator
to set the corresponding first column of data in {E2503} to be all zeros.
You may prevent the calculator from adjusting any cells by selecting only those
cells in this table that you want updated before clicking on the [Apply] button. If no
cells (or all cells) are selected in this table, then the entire table will be updated.
Technical details
The CFTC computes the fuel timing percentages from the fuel timing degrees
using the following equation:
% = t / (us * rpm * 0.00000006)
The CFTC computes the fuel timing degrees from the fuel timing percentages
using the following equation:
t =% * (us * rpm * 0.00000006)
Where:
 t is the injection timing in degrees of crankshaft rotation.
 us is the injection pulse width in microseconds.
 rpm is the engine speed.

[email protected] - 20 - www.efilive.com
 Dodge Cummins User Guide
Pass-Thru Licence and Flash a Controller
Follow these steps to license and flash the selected controller.
1. Open the EFILive Scan and Tune application.
2. Connect your FlashScan/AutoCal to your PC and your vehicle.
3. Turn the vehicle ignition to the On position, (not the Accessory position.
Vehicle must not be cranked/running when flashing).
4. Select the [F3: Tune] option in the left-hand pane.
5. Click on the Open button and select the calibration file for the controller you
wish to flash or license.
6. If tune file security has been applied to the tune file, review and accept the
Security Warning.
7. Click on the [F7: Full Flash] options in the left-hand pane.
8. Adjust Dodge Cummins Fast CAN Mode settings where necessary;
a. Unlimited Fast CAN delivers the fastest possible flash time and is
approx. 50% faster than standard flash routines.
b. Fast CAN is a little faster than standard, but more robust than Unlimited.
If you experience flash failures when using Unlimited Fast Can or Fast CAN, try
unchecking that option and retry the flash.

9. Click on the Check License button. This will indicate if the controller is already
licensed or needs to be licensed.
10. Where the controller is NOT licensed, select Activate License to license the
controller.
11. Select Yes to license the controller or No to close this window without licensing
the controller.

12. Select Yes to license the controller or No to close this window without licensing
the controller.

[email protected] - 21 - www.efilive.com
 Dodge Cummins User Guide

13. Select the Full Flash button to commence the flash.

14. While the ECM is flashing an Elapsed time indicator, an Estimated Time
Remaining indicator, and a Progress bar will display tracking the Flash
progress.
15. When the flash process is complete a countdown timer will be shown. When
prompted perform the following actions:
a. Turn the vehicle ignition Off.
b. Click on the Start button to begin the countdown timer.
c. DO NOT turn the vehicle ignition on until the countdown timer expires.
This time is critical to allow the ECM to perform internal, initialization
functions after a read/flash operation.

Move Tune and Log files from FlashScan/AutoCal to your PC

FlashScan/AutoCal V3
Connect FlashScan/AutoCal V3 as a USB Thumb Drive to Windows Explorer
1. To move tune files and log files from FlashScan V3 onto your PC;
2. Connect FlashScan V3 to your PC.
3. On FlashScan V3 navigate to Options -> File System -> USB Thumb Drive.
4. Using Windows Explorer, locate the files you wish to copy in the correct
folder of your FlashScan V3 and copy or drag the files into the desired folder
on your PC.

EFILive Explorer
To move tune files and log files from FlashScan/AutoCal V3 to your PC;

1. Connect FlashScan/AutoCal V3 to your PC.

2. Open EFILive Explorer.
3. Navigate to the directory on your PC where you wish to save the file.
4. Navigate to: [F3: Data Files].

[email protected] - 22 - www.efilive.com
 Dodge Cummins User Guide
5. Select appropriate folder on your FlashScan device and drag the selected file
to your PC.

FlashScan/AutoCal V2
To move tune files and log files from FlashScan/AutoCal V2 to your PC;

1. Connect FlashScan/AutoCal V2 to your PC.

2. Open EFILive Explorer.
3. Navigate to the directory on your PC where you wish to save the file.
4. Navigate to: [F3: Data Files].
5. Select appropriate folder on your FlashScan device and drag the selected file
to your PC.

Once tune and log files are copied from your FlashScan/AutoCal to your PC, they
can be opened/viewed using EFILive Scan and Tune.

[email protected] - 23 - www.efilive.com
 Dodge Cummins User Guide

Configure FlashScan/AutoCal
for BBX

There are a range of configuration files that must be installed on FlashScan and
AutoCal devices before the device can be used in standalone mode (BBX).
Follow these instructions to configure your FlashScan or AutoCal for BBX.
1. Connect your FlashScan or AutoCal to your PC.
2. Open the EFILive V8 Scan and Tune application.
3. Select the [F5: BBX] option in the left-hand pane.

EDA Data Logging

The EDA PID group aims to simplify the task of information sharing between users
as every individual data parameter has been selected with tuning feedback in
mind. If you choose to log additional data streams alongside the EDA stream it
may slow the data logging rate down by as much as 70%.
For FlashScan V2 and AutoCal V2, BBL is only supported where CSP5 and EDA
are installed.
For FlashScan V3 and AutoCal V3, BBL is supported regardless of whether CSP5
is installed.
To configure data logging;
1. Select the [F2: Scan] option in the left-hand pane.
2. Remove any unnecessary controller configurations to ensure capacity
restrictions are not exceeded.
3. Add your chosen controller(s) to your list;
a. Press the green '+' icon.
b. Right click on the Engine Controller box.
c. Navigate to Select the correct controller.
d. Select OK.

4. Click on the selected controller in the “BBL Enabled Controllers” window.

5. Highlight the EDA 1 folder in the “Available PIDs” window and drag into the
“Selected PIDs” window. *NOTE: For FlashScan/AutoCal V2 BBL is only
supported for Cummins Controllers that have CSP5 and EDA installed. Users
[email protected] - 24 - www.efilive.com
 Dodge Cummins User Guide
MUST select the entire EDA PID Group and flash a CSP5 operating system into
the ECM for effective data logging.

Configure Tuning
To configure flashing for your chosen controller on your FlashScan/AutoCal;
1. Select the [F3: Tune] option in the left-hand pane.
2. Remove any unnecessary controller configurations to ensure capacity
restrictions are not exceeded.
3. Add your chosen controller(s) to your list;
a. Press the green '+' icon.
b. Right click on the Engine Controller box.
c. Navigate to select the correct controller.
d. Select OK.

Tune File Switching

To configure the switching of CSP5 tune positions on your FlashScan/AutoCal
device;
1. Select the [F4: Switch] option in the left-hand pane.
2. Enter switchable tune names as appropriate.

Configure DTCs
To configure the display of trouble codes and descriptions onto FlashScan;
1. Select the [F5: DTC's] option in the left-hand pane.
2. Select appropriate DTC options.

Quick Setup
To configure BBX settings, device settings, and configure tune files for BBX;
[email protected] - 25 - www.efilive.com
 Dodge Cummins User Guide
1. Select the [F6: Quick Setup] option in the left-hand pane.
2. Select appropriate BBX configuration options.
3. Edit device settings as necessary. To automatically select the most recently used
controller and PID selection when FlashScan/AutoCal powers up:
a. Selecting the correct hardware on the [F6: Quick Setup] -> [Edit AutoCal
V3 Settings] button.
b. In the Device Settings window, navigate to [F6: Logging] and tick the “At
start-up, automatically re-select the most recently used PID list.”

4. Add tune files to the Quick Setup using the green '+' icon.

5. Write this configuration to FlashScan or AutoCal using the [Program Quick

Setup] function. The [Program Quick Setup] programs all selected Scan, Tune,
Switch, and DTC options, as well as selected device settings, BBX Quick
Setup selections and tune files. Once the device is programmed, FlashScan or
AutoCal is configured for BBX functions.
Each option can be programmed individually using the [Program] button on
each tab, or collectively using the [Program Quick Setup] option.

[email protected] - 26 - www.efilive.com
 Dodge Cummins User Guide

FlashScan/AutoCal Menu
Navigation

FlashScan/AutoCal V3
FlashScan/AutoCal V3 supports two menu structures; the EFILive standard menu
and the user defined menu. Where a used defined menu is not installed, the
EFILive standard menu will be displayed.

Data Logging
1. Configure FlashScan/AutoCal V3 for BBX features if not already setup.
2. Connect your FlashScan/AutoCal V3 device to your vehicle.
3. Turn the vehicle ignition to the On position.
4. Navigate to the Scan Tool -> F1 Select PIDs menu option.
5. Select correct controller type from BBX configured controllers.
6. Navigate to the F1 Scan Tool -> F2 Data Logging menu option.
7. Select F1: Record Data to commence the logging session.
8. The LCD will display recording status, elapsed time, frame count and the
selected PIDs.
9. A range of options are available while the Log is recording:
1. Select ✔ to pause/resume the log.
2. Select the up and down arrows to navigate through selected PIDs.
3. Select X, to stop data logging and save the logged data.
10. Start the vehicle and drive to record actual performance. Do not attempt to
operate a FlashScan/AutoCal device while your vehicle is in motion.
11. Select X on FlashScan/AutoCal V3 to stop data logging and save the log file.

Read a Controller (CMB and CMC only)

1. Configure FlashScan/AutoCal V3 for BBX features if not already setup.
2. Connect your FlashScan/AutoCal V3 device to your vehicle.
3. Turn the vehicle ignition to the On position. (Vehicle must not be cranked/running
when reading).
4. Navigate to the Tune Tool -> F1 Tuning -> F1 Read Tune menu option.
5. Select correct controller type from BBX configured controllers.
6. Click the ✔ button to initiate the read operation.
7. While the ECM is reading a Progress bar will display for the user to visually track
the read.
8. When the read process is complete, the saved file name will display. Select X to
close this message.
9. The Reset Controller notification will be shown, and the controller reset process
will begin.
1. Turn the vehicle ignition off.
2. Click on the Start button to begin the countdown timer.
3. DO NOT turn the vehicle ignition on until the countdown timer expires.
This time is critical to allow the ECM to perform internal, initialization
functions after a read or flash operation.

[email protected] - 27 - www.efilive.com
 Dodge Cummins User Guide
License and Flash a Controller
1. Configure FlashScan/AutoCal V3 for BBX features if not already setup.
2. Copy selected tune file(s) from your PC to FlashScan/AutoCal V3 if not
already copied via Quick Setup during step 1.
3. Connect your FlashScan/AutoCal V3 device to your vehicle.
4. Turn the vehicle ignition to the On position, (not the Accessory position.
Vehicle must not be cranked/running when flashing).
5. Navigate to the Tune Tool menu and select F1: Tuning -> F3 Program Full
menu option.
6. Navigate to the folder your tune file is located in and select ✔ to commence
the flash.
7. If the controller has not been licensed by this device previously, you will be
presented with an “Unlicensed Controller” message. Select ✔ to proceed with
licensing the controller, or X to exit without licensing the controller.
8. Select ✔ to confirm licensing the controller and commence the flash, or X to exit
without licensing the controller.
9. When the flash process is complete, select X to close the flash completed
message.
10. The Reset Controller notification will be shown, and the controller reset process
will begin.
1. Turn the vehicle ignition Off.
2. Click on the Start button to begin the countdown timer.
3. DO NOT turn the vehicle ignition on until the countdown timer
expires. This time is critical to allow the ECM to perform internal,
initialization functions after a read or flash operation.

Switch Tunes using FlashScan/AutoCal V3

1. Connect your FlashScan/AutoCal V3 device to your vehicle.
2. Turn the vehicle ignition to the On position.
3. Navigate to the Tune Tool menu and select F3 Switch Tunes -> F1 Switch
CSP5 menu option.

[email protected] - 28 - www.efilive.com
 Dodge Cummins User Guide
4. Use the arrows to navigate between tunes.
5. Press ✔ to make a tune selection.
6. You do not need to reselect the tune once the engine is shut down; the ECM
'remembers' which tune you previously selected.

FlashScan V2
Data Logging
1. Configure FlashScan V2 for BBX features if not already setup.
2. Connect your FlashScan V2 device to your vehicle.
3. Turn the vehicle ignition to the On position.
4. Navigate to the F1 Scan Tool - F1 Select PIDs menu option.
5. Select correct controller type from BBX configured controllers.
6. Navigate to the F1 Scan Tool - F2 Data Logging menu option.
7. Select F1: Record Data to commence the logging session.
8. The LCD will display the elapsed time, frame count and the selected PIDs.
9. A range of options are available while the Log is recording:
1. Select OK to pause/resume the log.
2. Select F1..F4 or Ctrl+F1..Ctrl+F4 to add “user notes” 1 thru 8 to the log.
3. Select Enter to toggle between Metric and US Customary units.
4. Select the up and down arrows to navigate through selected PIDs.
5. Select Cancel, to stop data logging and save the logged data.
10. Start the vehicle and drive to record actual performance. Do not attempt to
operate a FlashScan/AutoCal device while your vehicle is in motion.
11. Select Cancel on FlashScan V2 to stop data logging and save the log file.
NOTE: When data logging is activated you cannot return to the menu until
logging is stopped.

Read a Controller (CMB and CMC only)

1. Configure FlashScan V2 for BBX features if not already setup.
2. Connect your FlashScan V2 device to your vehicle.
3. Turn the vehicle ignition to the On position. (Vehicle must not be cranked/running
when reading).
4. Navigate to the F2 Tune Tool -> F1 Tuning -> F1 Read Tune menu option.
5. Select correct controller type from BBX configured controllers.
6. Click the OK button to initiate the read operation.
7. While the ECM is reading a Progress bar will display for the user to visually track
the read.
8. When the read process is complete, the saved file name will display. Select OK
to close this message.
9. The Reset Controller notification will be shown, and the controller reset process
will begin.
a. Turn the vehicle ignition Off.
b. Click on the Start button to begin the countdown timer.
c. DO NOT turn the vehicle ignition on until the countdown timer expires.
This time is critical to allow the ECM to perform internal, initialization
functions after a read or flash operation.

License and Flash a Controller

1. Configure FlashScan V2 for BBX features if not already setup.

[email protected] - 29 - www.efilive.com
 Dodge Cummins User Guide
2. Copy selected tune file(s) from your PC to FlashScan V2 if not already copied
via Quick Setup in step 1.
3. Connect your FlashScan V2 device to your vehicle.
4. Turn the vehicle ignition to the On position (not the Accessory position. Vehicle
must not be cranked/running when flashing).
5. Navigate to the F2 Tune Tool -> F1 Tuning and select F3 Program Full menu
option.
6. Using the arrow keys, navigate to the correct tune file and select OK.
7. If the controller has not been licensed by this device previously, you will be
presented with the License this controller now? message. Select Yes to
license the controller or No to exit without licensing the controller.
8. Select Yes to confirm licensing the controller and commence the flash, or No to
exit without licensing the controller.
9. When the flash process is complete the Reset Controller notification will be
shown. When prompted perform the following actions:
a. Turn the vehicle ignition Off.
b. Click on the Start button to begin the countdown timer.
c. DO NOT turn the vehicle ignition on until the countdown timer expires.
This time is critical to allow the ECM to perform internal functions after a
read/flash operation.

Switch Tunes using FlashScan V2

1. Connect your FlashScan V2 device to your vehicle.
2. Turn the vehicle ignition to the On position.
3. Navigate to the F2 Tune Tool -> F3 Switchable Tunes menu option
4. Select PIDs
5. Use the arrows to navigate between tunes.
6. Press OK to make a tune selection.
7. You do not need to reselect the tune once the engine is shut down; the ECM
'remembers' which tune you previously selected.

[email protected] - 30 - www.efilive.com
 Dodge Cummins User Guide

AutoCal V2
Data Logging
1. Configure AutoCal for BBX features if not already setup.
2. Connect your AutoCal device to your vehicle.
3. Turn the vehicle ignition to the On position.
4. Navigate to the Select PIDs menu option and select OK.
5. Select the correct controller type from BBX configured controllers and make a
selection using the OK button. Where only one controller is in the BBX,
executing the Select PIDs option will make that selection and return to the
menu.
6. Navigate to the Record Data option and select OK to commence the logging
session. AutoCal will display the following to commence the logging session;
a. Creating Log File.
b. Starting Scanner.
7. The Time indicator will increment to indicate recording has commenced.
8. Start the vehicle and drive to record actual performance.
9. Stop the vehicle and turn the ignition off prior to saving the log on AutoCal.
10. A range of options are available while the log is recording.
a. Select OK to pause/resume the log.
b. Select Next to scroll forward through the list of PIDs.
c. Select Prev to scroll backwards through the list of PIDs. Scrolling back
to the very first entry displays “Exit”, when “Exit” is displayed, click OK
to stop data logging and save the log.

Read a Controller (CMB and CMC only)

1. Configure AutoCal V2 for BBX features if not already setup.
2. Copy selected tune file(s) from your PC to AutoCal if not already copied via
Quick Setup in step 1.
3. Connect your AutoCal device to your vehicle.
4. Turn the vehicle ignition to the On position (not the Accessory position. Vehicle
must not be cranked/running when flashing).
5. Navigate using the arrow keys to the Read menu option.
6. Select the correct controller type from the previously configured BBX
controllers in the Read 1-5 options. (NOTE: Unused Read options are hidden
on the AutoCal Simple Menu).
7. Click the OK button to initiate the read operation.
8. When the read process is complete the following messages will be displayed.
a. Saving Wait
b. Checking
c. Saved as with file name displayed on the screen.
[email protected] - 31 - www.efilive.com
 Dodge Cummins User Guide
9. The Ignition Off NOW! notification will be shown, and the controller reset
process will begin.
a. Turn the vehicle ignition Off.
b. Click on the Start button to begin the countdown timer.
c. DO NOT turn the vehicle ignition on until the countdown timer expires.
This time is critical to allow the ECM to perform internal, initialization
functions after a read or flash operation.

License and Flash a Controller

1. Configure AutoCal for BBX features if not already setup.
2. Copy selected tune file(s) from your PC to AutoCal if not already copied via
Quick Setup in step 1.
3. Connect your AutoCal device to your vehicle.
4. Turn the vehicle ignition to the On position (not the Accessory position. Vehicle
must not be cranked/running when flashing).
5. Navigate using the arrow keys to Full 1-5 option. (NOTE: Unused Prog/Full
options are hidden on the AutoCal Simple Menu).
6. Select the correct tune file from those listed and select OK.
7. If the controller has not been licensed by this device previously, you will be
presented with the License controller message.
8. Select OK or Prev to exit without licensing the controller.
9. Select OK to license the controller and initiate the flash operation or Prev to
exit without licensing the controller.
10. When the flash process is complete the Ignition Off NOW! notification will be
shown. When prompted perform the following actions:
a. Turn the vehicle ignition off.
b. Click on the OK button to begin the countdown timer.
c. DO NOT turn the vehicle ignition on until the countdown timer expires.
This time is critical to allow the ECM to perform internal, initialization
functions after a read or flash operation.

Switch Tunes using AutoCal V2

1. Connect your AutoCal V2 device to your vehicle.
2. Turn the vehicle ignition to the On position.
3. Navigate to the Switch Tunes menu option
4. Select PIDs
5. Use the arrows to navigate between tunes.
6. Press OK to make a tune selection.
7. You do not need to reselect the tune once the engine is shut down; the ECM
'remembers' which tune you previously selected.

[email protected] - 32 - www.efilive.com
 Dodge Cummins User Guide

Support

Trouble Shooting
Should users encounter problems with the EFILive software, FlashScan or
AutoCal hardware they should:
1. Confirm software, firmware and boot block versions are up to date.
2. Check the fitment of the SGM Bypass cable (required for 2018+ vehicles).
3. Check RSA Digital Signature has been removed (required for all 2009+
vehicles).
4. Check that checksums are valid.
5. Check the base file matches the calibration for your vehicle.
6. Check Dodge Cummins Fast CAN Mode settings.
7. Only CMB and CMC stock files can be read from the ECM.
8. CSP5 tune files cannot be read from the ECM.
9. Remove/isolate all after-market devices including mobile phone adapters, after-
market equipment (audio systems, security, remote start etc.) and any devices
wired into the OBD port that may interfere with vehicle communications.
10. DO NOT operate any vehicle feature that may communicate on the data bus.
This includes opening or closing of hood, doors, windows, as well as changing
settings on radio, HVAC, connecting/removing charging devices etc.

Error Codes
If an error occurs while using AutoCal, users can look up the error code
description in the EFILive V8 Scan and Tune software.
The [F8: Tools] -> [F8: Error Codes] menu item provides an error code lookup
function, and the “EFILive Error Codes.pdf” document accessed by selecting the
Windows Start Icon and navigating to Program Files->EFILive->V8->Documents-
>EFILive Error Codes.pdf is also available. Both options provide error code
descriptions, causes and actions.
Should the issue not be resolved after reviewing the Error code list, end users
should contact their Tuner for support.

Checksums
Checksums perform a vital role in ensuring the integrity of the data in the tune file.
There are two main reasons that checksums display as invalid:
1. The data in the file is corrupt and MUST NOT be flashed into a controller.
2. The data in the file has been modified with a software package that did not
update the checksums – such as a hex editor.
Do not correct the checksums unless you know the tune file was modified outside
of the EFILive software and that the modifications are correct and accurate.
If you correct the checksums of a file with corrupt data you are merely masking
corruption. If you flash a corrupt file into a controller, you risk damaging the
controller and/or causing the vehicle to operate incorrectly.
[email protected] - 33 - www.efilive.com
 Dodge Cummins User Guide
Dodge Cummins Fast CAN Mode – CMD, CME, CMF
Three flash speeds exist for Dodge Cummins controllers;
1. Unlimited Fast CAN delivers the fastest possible flash time and is approx.
50% faster than standard flash routines.
2. Fast CAN is a little faster than standard, but more robust than Unlimited.
3. Standard can be used if you experience flash failures when using Unlimited
Fast Can or Fast CAN, try unchecking that option and retry the flash.
Cummins Fast CAN Mode can be adjusted the following ways:
1. During Pass-Thru flashing by adjusting the options on the [F3: Tune] -> [F7:
Full Flash] tab.
2. For BBF by adjusting the options on;
a. [F6:Devices] -> [F5: Options] tab and programming the device.
b. Via FlashScan and AutoCal hardware by editing the device options.

Cummins 5.9L ECM VIN Issues

The VIN in the .ctz tune file should always match the VIN in the vehicle prior to
flashing the ECM.
As part of the normal re-flash process for the 5.9L CM849B Cummins ECM, a
section of the flash memory is written that contains vehicle specific values,
including VIN and SKIM code. This part of the ECM is flashed every time the ECM
is programmed.
Flashing a tune from a different vehicle will cause a no start condition until the VIN
in the ECM is corrected to match the vehicle. If an attempt is made to start the
vehicle prior to correcting the VIN, other modules on the truck will detect the non-
matching VIN details setting C2206 "Vehicle Configuration Mismatch" DTC in
several modules. Once set, EFILive is UNABLE to correct this code and MIL,
resulting in a dealer visit.
To change the VIN in the .ctz tune file open the tune file and:
1. Navigate to [F4: Properties] -> [Controller Information] tab.
2. Enter the VIN.
3. Save the file prior to programming the ECM.

Failed Flash Recovery Methods

In the event that an ECM fails during the flashing process, recovery methods exist
to restore the ECM.

Flash Base with without tune file security restrictions.

In most instances, simply retrying the flash process will return the ECM to working
order.
In the instance where tuners apply security restrictions to a tune file, including
locking to the controller serial number, and the flash fails, you must try to recover
the ECM with a file that has no security restrictions in place (e.g. stock tune)
before attempting to reflash a file with security restrictions.

ROM Boot Recovery

In some flash failure instances the ECM may stop responding and cannot be
recovered to normal operation by simply retrying the flash.

[email protected] - 34 - www.efilive.com
 Dodge Cummins User Guide
Such situations may occur if the ECM was flashed with a non-compatible
operating system, or where the failed flash occurred right at the end of the process
but the ECM thinks it completed.
In these situations the ECM is usually only recoverable by forcing the ECM into
ROM Boot Recovery mode. Specialized bench programming equipment, such as
the BenchForce PowerBlock IV with ROM Boot Switch is required to perform this
task.
Tips to recover the ECM using this equipment includes:
1. The ECM must be powered down. (IGN switch off but battery power
connected.)
2. Hold the ROM Boot switch on.
3. Power the ECM and bench equipment.
4. Attempt to flash the ECM with your recovery file.
5. Once the flash is under way you can turn off the ROM Boot switch.

Test for Rogue Modules

For Customers with FlashScan/AutoCal V3 a range of test modes to check the
network for rogue modules that may cause read or flash operations to abort are
available.
Navigate to the Tune Tool -> F1: Tuning -> F4: Test OBD Network menu.
Select the Test CAN J1979 option for CAN based controllers.

Trace Files
V8 Scan and Tune *.htx files
When V8 Scan and Tune software reads or flashes a controller the details of the
read/flash process may be saved in trace files for diagnostic purposes.
In addition, users can manually save trace files where options do not perform the
desired outcome.
To manually generate a trace file, generate the error in V8 software, then open the
EFILive Control Panel and navigate to [F8: Trace] and select [Save Trace]. Users
can set the trace file and save location during this process.
Automatically generated trace files are created on your PC or laptop in the folder:
\Documents\EFILive\V8\Trace and are named using the following naming
convention:
YYYYMMDD_HHNNSS_T_CCC.htx, where:
 YYYYMMDD: is the year, month and day that the trace was recorded.
 HHNNSS: is the hour, minute and second that the trace was recorded.
 T: is the mode and is one of R=Read F=Full-Flash W=Cal-Flash.
 CCC: Is the controller type
 htx: is the file extension.

FlashScan/AutoCal V3 *.xalm files

Trace files are automatically saved where an error message is presented using the
device in BBX mode. Users can manually save trace files where options do not
perform the desired outcome, including for pass-thru functions.

[email protected] - 35 - www.efilive.com
 Dodge Cummins User Guide
To manually generate a trace file on FlashScan/AutoCal V3 navigate to Scan Tool
-> F3: Scan Options -> F1: Save Trace.
FlashScan/AutoCal V3 maintains an internal buffer of the most recent messages
sent to and received from the vehicle. That buffer is stored in RAM memory and is
wiped clean each time the device is powered off or rebooted. Therefore you MUST
save the trace file before powering off or rebooting the device.
Trace files are located in the EFILive -> Trace folder on FlashScan/AutoCal V3.
Trace files are named using the following naming convention:
yyyymmdd_hhnnss_<desc>.xalm, where:
 yyyymmdd: is the year, month and day that the trace was recorded.
 hhnnss: is the hour, minute and second that the trace was recorded.
 <desc>: is the description where;
o “User” means user generated trace files
o “xxx._x_$xxxx” identifies the 3 character controller ID, the
communication process upload/download, and the 4 digit error code.
 xalm: is the file extension.

FlashScan V2 Trace Files

Trace files are automatically saved where an error message is presented using the
device in BBX mode. Users can manually save trace files where options do not
perform the desired outcome.
To manually generate a trace file on FlashScan V2 navigate to F1 Scan Tool -> F3
Scan Options -> F1 Save Trace File.
FlashScan V2 maintains an internal buffer of the most recent messages sent to
and received from the vehicle. That buffer is stored in RAM memory and is wiped
clean each time the device is powered off or rebooted. Therefore you MUST save
the trace file before powering off or rebooting the device.
Trace files are located in the Scan folder on FlashScan V2. It will be named
USR_xxxx.efx, where xxxx is the unique file counter number.

AutoCal V2 Trace Files

Provided enough space exists in the [Data] file system of AutoCal V2 trace files
are automatically saved where an error message is presented using the device in
BBX mode. Users can manually save trace files where options do not perform the
desired outcome.
To manually generate a trace file on AutoCal V2 navigate to:
1. AutoCal (standard menu): Save Trace File
2. AutoCal (advanced menu): Scan Tool -> Save Trace File
AutoCal V2 maintains an internal buffer of the most recent messages sent to and
received from the vehicle. That buffer is stored in RAM memory and is wiped clean
each time the device is powered off or rebooted. Therefore you MUST save the
trace file before powering off or rebooting the device.
The trace file will be saved in the Scan folder on the device. It will be named
USR_xxxx.efx, where xxxx is the unique file counter number.

[email protected] - 36 - www.efilive.com
 Dodge Cummins User Guide
Knowledgebase
The EFILive Knowledgebase provides a detailed resource on how to configure and
use your EFILive software and hardware.

EFILive Authorized Dealer

If after reviewing this guide further assistance is required please contact the
EFILive Authorised Dealer from whom you purchased your product. They are your
first point of contact for EFILive support related inquiries.

How to Tune?
EFILive is tuning software and hardware - it is not a tune. Together the software
and hardware give users the tools to write tunes. EFILive does not provide tune
files, tuning advice or support, but do provide software support and hardware
support.
If your question is in relation to the actual tuning of your vehicle (e.g. how to gain
performance, economy etc.) then please ask these questions on the EFILive
Forum (http://forum.efilive.com/).

EFILive Service Desk

Should you require additional assistance after using this support guide, please
start a ticket on the EFILive Service Desk. Please include the following
information:
1. Dealer Name.
2. Device type.
3. Serial Number and Auth Code.
4. Your computer operating system.
5. Software and firmware versions.
6. Trace files.
7. Detailed information about your issue.

[email protected] - 37 - www.efilive.com