Andover Continuum

I/O System Reference

© 2010, Schneider Electric
All Rights Reserved
No part of this publication may be reproduced, read or stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical, photocopying,
recording, or otherwise, without prior written permission of Schneider Electric.
This document is produced in the United States of America.
Infinity is a trademark of Schneider Electric. All other trademarks are the property of their
respective owners.
Andover Continuum I/O System Reference
Rev. K
April, 2010
Schneider Electric part number: 30-3001-499

This manual (Rev. K) corresponds to the following firmware versions:

IOU Modules Version Released
AC-1 23
AC-1 Plus 25
AO-4, DO-6, DI-6, DI-8, DM-20, LB-8, LC-1, LS-8, 10
MI-6
DO-4 11
LO-2 11
UI-8 12
VS-8/VS-8T 11
VT-1 21

Related Documents:
Andover Continuum Power Supply Reference, 30-3001-702
Andover Continuum NetController II Operation & Technical Reference, 30-3001-995
Andover Continuum Enclosure and Display Module Reference, 30-3001-711
Andover Continuum I/O System Installation Sheet, 30-3001-716

The information in this document is furnished for informational purposes only, is subject to change
without notice, and should not be construed as a commitment by Schneider Electric. Schneider
Electric assumes no liability for any errors or inaccuracies that may appear in this document.
st
On October 1 2009, TAC became the Buildings Business of its parent company Schneider
Electric. This document reflects the visual identity of Schneider Electric. However, there remain
references to TAC as a corporate brand throughout the Andover Continuum software. In those
instances, the documentation still refers to TAC - only to portray the user interface accurately. As
the software is updated, these documentation references will be changed to reflect appropriate
brand and software changes. All brand names, trademarks, and registered marks are the property
of their respective owners.
Schneider Electric
One High Street
North Andover, MA 01845
(978) 975-9600
Fax: (978) 975-9782
http://www.schneider-electric.com/buildings
ii Schneider Electric
Regulatory Notices

Radio Interference – Federal Communications Commission

This equipment has been tested, and it complies with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions in this manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference, in which case you will be required to correct the interference at your own expense.

Radio Interference – Canadian Department of Communications

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital
apparatus set out in the Radio Interference Regulations of the Canadian Department of
Communications.

Brouillage Radioélectrique – Ministère des Communications

du Canada
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de la Classe A prescrites dans le Règlement sur le brouillage
radioélectrique édicté par le ministère des Communications du Canada.

CE – Compliance to European Union (EU)

This equipment complies with the European Union (EU) standards specified in the EU
EMC directive 89/336/EEC and/or the product-safety low voltage directive 73/23/EEC,
governing the European community.

C-Tick – Australian Communications Authority (ACA)

This equipment carries the C-Tick label and complies with EMC and radio
communications regulations of the Australian Communications Authority (ACA),
governing the Australian and New Zealand communities.

WEEE – Directive of the European Union (EU)

This equipment and its packaging carry the waste electrical and electronic equipment
(WEEE) label, in compliance with European Union (EU) Directive 2002/96/EC,
governing the disposal and recycling of electrical and electronic equipment in the
European community.

Andover Continuum I/O System Technical Reference iii

Contents
Introduction...................................................................... 1
Mechanical Installation ................................................... 4
Overall Dimensions....................................................................... 7
Enclosure-Mounted Modules ....................................................... 8
I/O Module Layout Convention .................................................... 9
CPU-I/O Connections .................................................... 10
Connection of I/O Modules......................................................... 11
Maximum Number of I/O Modules ............................................. 12
Calculating Additional Power Supply Requirements .............. 13
Maximum Length of I/O Bus ...................................................... 13
Cable Recommendations ........................................................... 13
Power Wiring Guideline Table ................................................... 15
Connecting Remote I/O Modules with ACC-LON (RS-485) ..... 16
Connecting Remote I/O Modules with LON FTT-10A .............. 20
Replacing or Adding I/O Modules ................................ 26
Module Configuration.................................................... 27
Individual Module Wiring .............................................. 32
General Wiring Concerns for All Modules ................................ 32
Grounding the Modules .............................................................. 32
ESD Warning................................................................................ 33
INPUT Modules
UI-8-10 / UI-8-10-10V.................................................................... 35
DI-6-AC / DI-6-AC-HV................................................................... 53
DI-8................................................................................................ 60
MI-6 ............................................................................................... 69
OUTPUT Modules
DM-20............................................................................................ 76
AO-4-8 / AO-4-8-O........................................................................ 86
DO-4-R / DO-4-R-O....................................................................... 95
DO-6-TR ...................................................................................... 103
LO-2 / LO-2-O ............................................................................. 111
MIXED Modules
DIO-20 ......................................................................................... 123
AC-1 ............................................................................................ 129
AC-1A.......................................................................................... 148
AC-1 Plus ................................................................................... 167
VS-8-4 / VS-8-4-T........................................................................ 193
VT-1............................................................................................. 199

iv Schneider Electric
 TCX 865
ANDOVER CONTINUUM
I/O Systems

This manual describes the installation, care and use of all Andover Continuum I/O
modules.

The Andover Continuum Ethernet-based intelligent building system allows you to mix and
match various combinations of DIN rail-mounted modules⎯high density I/O, CPU and
power supply, and your choice of several user interface modules⎯in a single controller
location to meet your building’s control and monitoring needs. With the Andover
Continuum system, as your network grows, simply add or replace I/O modules as
needed.

The Andover Continuum I/O modules feature a casing designed for natural convection
cooling, and a 3-position front cover for easy, hands-free access. Built-in quick-release
fasteners at the back of each I/O module are provided for DIN rail mounting⎯no tools
required. These fasteners also snap into a locked position for panel mounting. Input and
output connectors are located at the bottom of each I/O module and are removable for
easy field access and maintenance. All Andover Continuum modules are designed for
mounting in an optional NEMA 1-style Andover Continuum enclosure.

The Andover Continuum I/O modules communicate with the Andover Continuum
NetController and NetController II CPU modules. (This manual uses the generic name,
NetController for both series of CPU modules.) Like all Andover Continuum modules, the
I/O modules snap together directly via built-in connectors on either side; so network
expansion is quick and easy. Both power transmission and communication signals
between the power supply module, NetController CPU module, and all I/O modules feed
through this connection. For added convenience in certain applications, such as door
control or lighting control, a single module or groups of I/O modules can be remotely
located and connected using approved cable and powered from a local power supply.
Each I/O module features its own push-button for quick and easy network
commissioning.

This document covers the standard Input and Output modules. For information
regarding the special Andover Continuum enclosure door-mounted display
modules consult the Andover Continuum Enclosure and Display Module
Reference.

Andover Continuum I/O System Reference 1

I/O System Introduction

The Andover Continuum I/O system comprises a series of modules separated by function
that connect via a common electrical communications network. Each functional
component (module) is enclosed in a plastic case containing all of its connections to the
outside world. Modules are connected to a central controller via a standard five-conductor
connector.

The Andover Continuum system includes at least one power supply and a single CPU
module. I/O modules provide the controller with the ability to interface with the outside
world. They connect directly and communicate with the CPU. The following is a typical
architecture drawing of an Andover Continuum System:

Power Supply Controller I/O Modules

Andover Continuum I/O modules included in this document are INPUT, OUTPUT and
MIXED. Display modules are covered in the Andover Continuum Enclosure & Display
Module Reference 30-3001-711.

2 Schneider Electric
The INPUT modules available are:
• UI-8-10; Universal Input Module * † **
• UI-8-10-10V; Universal Input Module * † **
• DI-6-AC; AC Digital Input Module (12-120V)
• DI-6-AC-HV; AC Digital Input Module (120/240V)
• DI-8; Digital Input Module * †
• DM-20; Digital Input/Output Module * †
• MI-6; MilliAmp Input Module *

The OUTPUT modules available are:

• AO-4-8; Analog Output Module *
• AO-4-8-O; Analog Output Module (with override) *
• DO-4-R; Relay Output Module * † **
• DO-4-R-O; Relay Output Module (with override) * † **
• DO-4A-R; Relay Output Module *
• DO-4A-R-O; Relay Output Module (with override) *
• DO-6-TR; Triac Output Module
• LO-2; Lighting Output Module
• LO-2-O; Lighting Output Module (with override)

The MIXED modules available are:

• DIO-20; Input/Output Module
• AC-1; Door, Access Control, Wiegand Module † **
• AC-1A; Door, Access Control, Wiegand Module † **
• AC-1 Plus; Door, Access Control, Wiegand/ABA/Ck34 Module † **
• VS-8-4; Video Switch Module †
• VS-8-4-T; Video Switch with Titling Module †
• VT-1; Voice Telecom Module

* These modules are also listed for smoke control applications. The model number for a smoke
control listed part includes an ‘-S’ suffix.

† These modules are listed for UL 294 Access Control Applications. See also: Andover
Continuum UL 294 Access Control Systems Reference, 30-3001-746.

(**) These modules are listed for UL 1076 Applications. See also: Andover Continuum UL 1076
Burglar Alarm Systems Reference, 30-3001-800.

Andover Continuum I/O System Reference 3

Mechanical Installation
Each I/O module, except the Display variety, is enclosed in a plastic case that is designed to
be mounted on a standard DIN rail or fastened to a panel.

Note: In order to meet agency requirements in the United States, it is necessary that
the modules along with the power supply and CPU be housed in another metal
enclosure i.e., a NEMA box or the Andover Continuum enclosure. Only Schneider
Electric enclosure models ENC-0DISP and ENC-3DISP are approved for UL 294 Access
Control Systems.

The two types of I/O module plastic cases are illustrated below:
Status Indicators
& switches

Status indicators and operator switches are located on the indicator panel. Other
switches available for module configuration may be accessed by lifting the hinged door of
the smaller module.

Connections to
controlled/sensed
equipment

4 Schneider Electric
On the back of each module are molded DIN rail guide fingers. The design allows the
module to easily hook onto and slide along a standard DIN rail. The fingers also allow the
module to be mounted directly to a panel using them as a bracket. A stand-off is molded
into the locking finger. To mount the module on a panel, extend the locking fingers and
insert screws through the standoffs as shown below:

Locking Fingers Panel Mounting

DIN Rail Mounting: With the mounting brackets (locking fingers) extended outward, hook
the module onto the DIN rail as shown below:

Andover Continuum I/O System Reference 5

Slide the module into position.

Press the upper bracket into its locked position.

Press the lower mounting bracket(s) inward until it locks the module in place.

Grounding the Modules

All I/O modules except the VS-8 include a metal clip that is built into the locking
mechanism on the back of the case. Mounting the module on an electrically conductive
metal surface or DIN rail automatically provides an Earth ground. The VS-8 includes a
ground stud that must be connected to Earth ground. It is important that this connection
be made as close to the module as possible.
Note: Anodized Aluminum DIN rails are not electrically conductive.

6 Schneider Electric
Overall Dimensions
The overall dimensions of the two types of I/O cases are as shown:

6.70''
(170.2 mm)

2.50 '' 3.50 ''

(63.5 mm) (88.5 mm)

6.70''
(170.2 mm)

2.50 ''
(63.5 mm) 9.0 ''
(228.7 mm)

Andover Continuum I/O System Reference 7

Enclosure-Mounted Modules
The Schneider Electric enclosure provides a place to mount a power supply, CPU and up
to 10 DIN rail mounted I/O modules. Several display modules can be affixed to the front
panel.

The Display modules are designed to fit into openings left by removing panels in the front
door.

The enclosure is a 6” deep NEMA box with integral display panels, DIN rails, cable
troughs and a battery storage compartment.

DIN Rail

Cable Trough

Battery
Storage

The enclosure features three DIN rails and cable management accessories. Use of the
new enclosure is not required; however, it provides a convenient method of constructing
small local systems.

8 Schneider Electric
The front door of the enclosure contains removable sections into which special operator
display and control modules may be mounted. Alternately, Plexiglas panels may be used
to view the status lights of all internal modules when the door is closed.

5HPRYDEOH
'LVSOD\3DQHOV

Spacers for
Additional Displays

I/O Module Layout Convention

By convention, I/O modules should be separated according to function and whether they
are connected to low or high voltages.

Typically, Input wires should enter from only one of the wiring troughs, and should come
from the left side of the rack.

Output wires should enter from the other wiring trough, and should come from the right
side of the rack.

A good system would be to install all your input modules on one DIN rail, output modules
on the next rail, and so on.

Andover Continuum I/O System Reference 9

CPU-I/O Connections
The Andover Continuum NetController/NetController II CPU module includes a
connector on the upper right side of its case for further distribution of the 24 VDC
input power and special I/O communications signals to all I/O modules. Andover
Continuum I/O modules use these signals for power and communications.

The power-I/O connector is a five pin male assembly that is designed to easily insert
directly into the left side connector of any I/O module. The signals within this
connector are as follows:

PIN Function
5 +24 VDC 5
4
3
2

4 24 VDC Return 1

3 Shield
2 Comm B
1 Comm A

The main system power supply generates a +24 VDC source for the CPU. This
power source is received through the input power connector on the left side of the
CPU module and sent through to pins 4 and 5 of this connector.

All Andover Continuum I/O modules can operate at 24V. Some have extended ranges to
allow operation at lower voltages. Refer to the individual specifications for each module.

Communications between the CPU and I/O modules is through a two-signal serial
interface that is factory configured as either RS 485 ACC-LON or LON FTT-10A.

Pins 1 and 2 (Comm B and Comm A) provide the electrical connection for this interface.
Pin 3 (Shield) is the communications signal shield connection. This is not an Earth
ground connection. Proper shielding requires that the installer connect all shields
together. The CPU (if grounded properly) provides the single Earth ground point for all
modules. Each I/O also has its own Earth ground connection.

10 Schneider Electric
Connection of I/O Modules
When installing I/O modules it is imperative that the installer supply a solid Earth ground
connection to the pins provided.
The CPU can directly connect to I/O without the use of cables through a system of built-in
plugs and jacks. All I/O modules include two complementary module inter-connectors.
Creating a system is as simple as physically plugging the modules together.

Power Supply CPU

I/O I/O

Power Supply CPU I/O I/O

In vertical extended systems, I/O modules may be located above or below other modules.
In this case, cable assemblies bridge the I/O modules together.

I/O

Power Supply CPU

The cables necessary to connect the CPU and external I/O modules are attached using a
plug-in screw terminal connector. Connection between the modules is one-to-one
straightforward wiring as shown below:

5 5
4 4
3 3
2 2
1 1

Connectors are available from Schneider Electric under part number 01-0010-840.

Andover Continuum I/O System Reference 11

Maximum Number of I/O Modules
The Andover Continuum system allows a maximum of 32 I/O modules per CPU. There is
also a limit based upon the capacity of the power supply feeding the modules.
Note: It is possible to insert auxiliary power supplies into the I/O bus to increase the
number of modules supported, up to a maximum of 32. The Andover Continuum Power
Supply Reference, 30-3001-702, includes information on auxiliary supply installation.
• PS 120/240 AC 50 U, UPS power supply: 35 Watts of power available
• PS 120/240 AC 85 U, UPS power supply: 70 Watts of power available
• PS 120/240 AC 50, non-UPS power supply: 50 Watts of power available
• PS 120/240 AC 85, non-UPS power supply: 85 Watts of power available
• PS –48 DC 50, Battery operated power supply: 50 Watts of power available
UPS power supplies (models with the designation ‘U’) include battery charging circuitry
that consumes 15 Watts of the total power available. This is why the UPS supplies are
listed with less available Wattage.
To determine the maximum number of I/O modules each power supply can support, subtract
the power requirements for each module from the maximum available per supply.
If the supply also powers a NetController, be sure to subtract the 10 Watts it consumes.
The power requirements for the NetController and each I/O module* is listed below:

Power @24.0 VDC

Module (Watts) (mA)
NetController 10 417
UI-8-10 & UI-8-10-10V; Universal Input Modules 0.7 29
DI-6 AC & DI-6 AC HV; AC Digital Input Modules 0.7 29
DI-8; Digital Input Module 0.8 33
MI-6; MilliAmp Input Module 3.8 158
DM-20; Digital Input/Output Module 0.5 ** 20 **
AO-4-8 & AO-4-8-O; Analog Output Modules 3.8 158
DO-4(A)-R & DO-4(A)-R-O; Relay Output Modules 2.8 116
DO-6-TR; Triac Output Module 1.1 45
LO-2 & LO-2-O; Lighting Output Modules 0.4 16
AC-1; Door, Access Control, Module 2.6 ** 108
AC-1A; Door, Access Control, Module 2.0 ** 83
AC-1 Plus; Door, Access Control, Module 2.2 ** 92
VS-8 & VS-8-T; Video Switch Module 2.0 83
VT-1; Voice Telecom Module 1.5 63

* Power requirements for Display Modules can be found in the Andover Continuum Enclosure and
Display Module Reference, 30-3001-711.

** Listed power value does not include any devices attached and powered by the module
(card readers or DIO-20). Refer to the formulas on the next page for calculation.

12 Schneider Electric
Calculating Additional Power Supply Requirements
The DM-20 and all the AC Series access control modules have the built-in capability to
power an external device. The module power requirements listed in the table on the
previous page does not include power consumption information for these devices. In the
case of external card readers and keypads, it is not possible for us to determine the
power requirements of all the combinations of manufacturer’s products you might
connect. However, we can provide a simple formula to determine any additional power
the module may draw when powering those devices.

Module Formula Example

AC-1: 15 X (Reader/Keypad Current Amps) 15 X 0.05 (50 mA reader) = .75W

AC-1A:
AC-1Plus: Module X Reader/Keypad 24 X 0.05 (50 mA reader) = 1.20W
Supply Voltage Current (Amps)

DM-20 Refer to the DIO-20 section of this document for additional power requirements

Maximum Length of I/O Bus

The Andover Continuum I/O Bus is a network. Networks are limited by cable lengths
because electrical signals lose power and distort as they travel along wire. The longer the
wire, the lower the signal strength. The following are the maximum cable length
specifications:
RS-485 2000 ft. (610 m)
FTT-10A 8858 ft. (2700 m) double termination
1640 ft. (500 m) free topology

Cable Recommendations
Data Cable (Pins 1, 2 and 3)
You must use shielded cable for the data lines (pins 1, 2 and 3) to provide reliable
communications and to ensure compliance with the Class A FCC limits (USA).
ACC-LON (RS-485)
The data cable should be 24-gauge (0.25 mm), single-twisted-pair, tinned, shielded
copper wire with an impedance of 100-120 Ωs and a nominal velocity of propagation
of 78%.
Capacitance of the cable should be below 12.5 pF/ft (41 pF/m) between conductors
and below 22 pF/ft (72 pF/m) between the conductor connected to ground and the
next conductor.
The following cable meets all of the data cable specifications:
Belden 9729, double twisted pair, shielded

Andover Continuum I/O System Reference 13

 LON FTT-10A
The installer can choose a variety of cables, depending on cost, availability, and
performance. Performance can vary with cable type. The transmission specification
depends on such factors as resistance, mutual capacitance, and the velocity of
propagation. Currently, Schneider Electric has documented system performance on
the cable types shown below. They are listed in order of performance.

Cable Type Wire dia./AWG

Belden 85102, single twisted pair, stranded 19/29, 16
unshielded
Belden 8471, single twisted pair, stranded 19/29, 16
unshielded, 600C
Level IV, twisted pair, typically solid & unshielded 22
TIA568A Category 5, twisted pair 24
If a shielded cable is used, the shield should be connected to earth ground via a 470 kΩ, 1/4
W <=10%, metal film resistor to prevent static charge build-up.

Power Cable (Pins 4 and 5)

You should use shielded cable for the power lines as well (pins 4 and 5) to ensure noise
immunity and therefore more reliable operation. The shield would be connected to pin 3
like that of the data cable.

The gauge of the power cable is determined by the power it carries. As indicated
previously, the longer the wire the more voltage drop. Do not allow the power supply
voltage measured at the furthest remote module to drop more than the allowable amount:

24 VDC modules: 2V (1V for the power run and 1V for the return run)
10-28 VDC modules: 12V (6V for the power run and 6V for the return run)

Voltage drop can be calculated by using Ohms Law:

Voltage=Current x Resistance

A table providing some guidelines for choosing wire gauge is included on the next page.

14 Schneider Electric
Power Wiring Guideline Table
The following is a conservative estimate of typical power consumptions and their related
wire gauge and number of feet:

24 VDC Modules
Total I/O Power Draw (Watts)
10 20 30 40 50
AWG Resistance
per 1000 ft Distance in Feet (meters)
(305 m)
14 2.5 585 (178) 255 (78) 145 (44) 90 (27) 57 (17)
16 4 366 (111) 159 (48) 91 (28) 56 (17) 36 (11)
18 6 244 (74) 106 (32) 60 (18) 38 (12) 24 (7)
20 10 146 (44) 64 (20) 36 (11) 23 (7) 14 (4)
22 15 98 (30) 43 (13) 24 (7) 15 (6) 10 (3)
24 24 61 (19) 27 (8) 15 (5) 9 (3) 6 (2)

10 - 28 VDC Modules
Total I/O Power Draw (Watts)
10 20 30 40 50
AWG Resistance
per 1000 ft Distance in Feet (meters)
(305 m)
14 2.5 3885 (1184) 1905 (581) 1245 (379) 915 (279) 717 (219)
16 4 2428 (740) 1191 (363) 778 (237) 572 (174) 448 (137)
18 6 1619 (493) 794 (242) 519 (158) 381 (116) 299 (91)
20 10 971 (296) 476 (145) 311 (95) 229 (70) 179 (55)
22 15 648 (198) 318 (97) 208 (63) 153 (47) 120 (37)
24 24 405 (123) 198 (60) 130 (40) 95 (29) 75 (23)

These tables are intended as a guide. There is no way to account for every Andover Continuum I/O
permutation. External noise suppression may be required if the power wiring is run in a noisy
environment.

Andover Continuum I/O System Reference 15

Connecting Remote I/O Modules with ACC-LON (RS-485)
The Andover Continuum system allows I/O modules to be placed in a remote location
from the CPU (NetController). Long cable lengths in ACC-LON (RS 485)-based networks
can cause signal communications problems on the I/O bus.

When locating an I/O module remotely on an RS 485-based bus, it is necessary to add

an external 120 Ω terminator resistor to the bus to compensate for the distance. The
terminator must be connected at both ends of the bus for proper operation.

The following diagrams are typical installations that indicate the correct placement of the
terminator:

Simple CPU and 1 ACC-LON Remote I/O Module:

The I/O Bus that needs to be terminated is the one formed by the cable attaching the
remote module to the CPU. In this case, a terminator resistor is connected across the
communications lines (pins 1 & 2) directly at the NetController and again at the remote
I/O module.

CPU 5 5
4 4
3 3
2 2
1 1

120 Ω
Resistor Remote
I/O 120 Ω
Resistor
Module

16 Schneider Electric
CPU with Local and 1 ACC-LON Remote I/O Module:

The I/O Bus that needs to be terminated is the one formed by the cable that starts at
the NetController and ends at the remote module. The bus that extends from the
NetController through the local I/O stack does not need termination. In this case, the
terminator resistor is connected directly across the communications lines (pins 1 & 2) at
the NetController and again at the remote I/O module.

Local Local
CPU I/O
5
I/O 4

120 Ω
Resistor

Remote
I/O 120 Ω
Module Resistor

Andover Continuum I/O System Reference 17

 CPU with Local and Several Remote ACC-LON I/O Modules:

The I/O Bus that needs to be terminated is the one formed by the cable that starts at
the NetController and ends at the first remote module. The bus that extends from the
NetController through the local I/O stack and the one that starts at the first remote
module and extends through subsequent modules do not need termination. In this
case, the terminator resistor is connected directly across the communications lines
(pins 1 & 2) at the NetController and again at the first remote I/O module.

CPU Local 5
I/O 4

120 Ω
Resistor

Remote Remote
I/O I/O 120 Ω
Module Module Resistor

18 Schneider Electric
CPU with Two Remote ACC-LON Modules Separated by Distance:

The I/O Bus that needs to be terminated is the one formed by both cables on either
end of the first remote I/O module. In this case, the bus begins at the NetController,
flows by the first remote module and ends at the second. The terminator resistor is
connected directly across the communications lines (pins 1 & 2) at the NetController
and again at the last remote I/O module. If the last module is actually a stack of
directly connected I/O modules, the terminator is placed at the first module of the
stack as indicated in the scenario described on the previous page.

CPU 5

120 Ω
Resistor
5
5
4
4
3
3
2
2
1
1

Remote Remote
I/O 120 Ω
I/O Resistor
Module Module

Andover Continuum I/O System Reference 19

Connecting Remote I/O Modules with LON FTT-10A
The ACC LON bus topology wiring (RS-485) consists of a network of I/O modules that
are interconnected using a shielded twisted wire pair. In accordance with RS-485
guidelines, all of the devices must be wired in a bus topology to limit electrical reflections
and ensure reliable communications. There is a high cost associated with installing and
maintaining the cable plant that links together the many elements of an RS-485 based
control system. Bus topology wiring is more time consuming and expensive to install
because the installer is unable to branch or star the wiring where convenient: all devices
must be connected directly to the main bus.

The best solution for reducing installation and maintenance costs and simplifying system
modifications is a flexible topology communication system. Echelon's free topology
transceiver (FTT) technology offers just such a solution, and provides an elegant and
inexpensive method of interconnecting the different elements of a distributed control
system.

The Echelon LON FTT-10A free topology architecture allows you to wire Andover
Continuum I/O modules with virtually no topology restrictions.

Unlike ACC-LON, the FTT-10A system uses a free topology wiring scheme that supports
star, loop, and/or bus wiring. This design has many advantages. First, the installer is free
to select the method of wiring that best suits the installation, reducing the need for
advanced planning and allowing last minute changes at the installation site. Second,
retrofit installations with existing wiring plants can be accommodated with minimal, if any,
rewiring. This capability ensures that FTT-10A technology can be adapted to both old and
new projects. Finally, free topology permits Andover Continuum systems to be expanded
in the future by simply tapping into the existing wiring where it is most convenient to do
so. This reduces the time and expense of system expansion, and from the customer's
perspective, keeps down the life cycle cost of the free topology network.

IMPORTANT FTT-10A NETWORK INSTALLATION NOTICE

The termination and wiring information provided in this guide is a small subset of the
complete technical information presented by Echelon Corporation in their FTT-10A
installation documentation. It is highly recommended that you obtain their document and
read the sections pertaining to network installation. As a courtesy, the Echelon FTT-10A
documentation has been included on the TAC TSD website.

The document filename is Echelon FTT-10A.pdf

20 Schneider Electric
FTT-10A Cable Termination (see important notice on the previous page)
When locating an I/O module remotely on a LON FTT-10A-based system, it is necessary
to add an external terminator to the wiring to compensate for the distance. The terminator
can be connected at both ends or at one central point.

* The Schneider Electric implementation of the Lon FTT-10A network can connect to a Link-
Power network; however, it does not use the Link Power.

Free Topology Segment

In a free topology segment, only one termination is required and may be placed
anywhere on the free topology segment. Using 24 AWG cable the maximum loop
impedance is 75 Ωs.

Termination Termination
Non-Link Power network Link Power network
Resistor = 52.30±1%, 1/8W Resistor = 52.30±1%, 1/8W
Capacitors = 100 μF 50V min.

R1 52.3 Ω ± 1%

Doubly Terminated Bus Topology Segment

In a doubly terminated bus topology, two terminations are required, one at each end of
the bus. Using 24 AWG cable the maximum loop impedance is 150 Ωs.

Termination Termination
Non-Link Power network Link Power network
Resistor = 105 Ω±1%, 1/8W Resistor = 105 Ω±1%, 1/8W
Capacitors = 100 μF 50V min.

R1 105 Ω ± 1%

Andover Continuum I/O System Reference 21

The following characteristics apply when using doubly terminated or free topology wiring
schemes:

1. Network lengths vary for doubly terminated vs. free topology.

2. Network lengths vary based on cable type.
3. FTT-I/O has two specifications for a free topology network: total wire
length and node-to-node wire length (which also applies to termination).

A doubly terminated bus may have stubs of up to 3 meters from a bus to each node.

Doubly Terminated Bus Topology Specifications

Maximum bus length (meters)

Belden 85102 2700
Belden 8471 2700
Level IV, 22AWG 1400
JY (St) Y 2x2x0.8 900
TIA Category 5 900

The free topology transmission specification includes two components that must be met
for proper system operation. The distance from each transceiver to all other
transceivers and to the termination (including the LPI-10 termination, if used) must not
exceed the maximum node-to-node distance. If multiple paths exist, e.g., a loop
topology, then the longest path should be used for calculations. The maximum total
wire length is the total amount of wire connected per segment.

Free Topology Specifications

Maximum node- Maximum total

to-node distance wire length
(meters) (meters)
Belden 85102 500 500
Belden 8471 400 500
Level IV, 22AWG 400 500
JY (St) Y 2x2x0.8 320 500
TIA Category 5 250 450

The following pages contain diagrams of typical installations that indicate the correct
placement of the terminator:

22 Schneider Electric
Example of Maximum Total and Node-to-Node Lengths

Power Supply CPU

Maximum Wire
Length
I/O

I/O Node-to-Node
Length

I/O

I/O

I/O

Andover Continuum I/O System Reference 23

 CPU with Local and a CPU with Several Remote FTT-10A I/O Modules*:

Power Supply CPU I/O I/O I/O I/O I/O 3

2 52.3 Ω
1

Power Supply CPU

I/O

I/O

I/O

I/O

I/O 3
2 52.3 Ω
1

* See Important Installation Notice on page 20

24 Schneider Electric
CPU with Several Remote FTT-10A I/O Modules and Doubly Terminated Bus*:

Power Supply CPU 3

2 105 Ω
1

I/O

I/O

I/O

I/O

I/O 3
2 105 Ω
1

* See Important Installation Notice on page 20

Andover Continuum I/O System Reference 25

Replacing or Adding I/O Modules
There are two ways to replace an I/O module to minimize the potential for long-term harm
to any equipment. The procedure that you follow depends upon the exact installation and
the circumstances that exist at the time of replacement. Both procedures are described
below. In either case, the controlled equipment must be overridden during the process. If
no external method of override exists, the equipment will go off.

Remove all power from the NetController and I/O modules:

1. Turn power supply off.
2. Disconnect the batteries.
3. Replace or add the I/O module.
4. Turn power supply on.
5. Reconnect batteries.
6. Reload NetController

Remove power to the I/O bus only:

1. Ensure that batteries are connected and fully charged.
2. Turn power supply off.
3. On the CyberStation workstation or Command Terminal Interface, cd to the
appropriate controller in the command line: type “set IOUPower = off”. The
battery will now only power the CPU and modem (if applicable).
4. Replace or add the I/O module.
5. Restore power.
6. If the NetController version is prior to 1.03, type “set IOUPower = on” in the
command line in CyberStation or Command Terminal Interface.

26 Schneider Electric
Module Configuration
This section of the document describes the procedure of configuring each module so that
it will be recognized by the Andover Continuum hardware. The following procedure is
common to all modules. Follow these instructions in the order given to assure proper
operation of the module.
It is assumed that you have knowledge or have access to someone who does have
knowledge of the operation of the CyberStation workstation. It is also assumed that your
CyberStation has configuration capabilities, is operating, logged-in and that the
NetController connecting to the modules you are trying to configure has already been
configured.

Commissioning a New I/O Module - CyberStation

When you install a new I/O module onto the bus you must commission the unit before it
will operate properly. Follow the steps below to properly commission an I/O module using
the CyberStation workstation:

Remove power from the I/O Bus where the module is to be installed
Step 1 On the I/O Bus: Connect the IOU Module
Connect the IOU Module to the I/O Bus.
Step 2 On the I/O Bus: Restore Power
Restore power to the I/O Bus.
Step 3 From CyberStation: Create the IOU Module
Log onto a CyberStation and create a new IOU module via the IOUModule
editor.
Step 4 From CyberStation: Assign an IOU number to the Module
During the creation process, you assign a unique number to the module being
configured.
Step 5 If the module is not easily accessible: Enter the module ID into the
Module ID text field.
Enter the module ID found on the label inside the cover of the module into the
field and click the Apply button, then skip to Step 8.
Step 6 If the module is easily accessible: Click the Learn Button on CyberStation
After creating the module and assigning the number, click the Learn button. A
dialog box displays requesting the operator to press the Commission button on
the physical module.
Step 7 On local Modules: Press the Commission button on the Module
Press the Commission button found on the front panel of the module. Clicking
this button sends information from the module to CyberStation. When you push
the Commission button, the dialog box should disappear indicating that it
received the information from the module.

Andover Continuum I/O System Reference 27

Step 8 On the CyberStation: Refresh the Form
When you refresh the form you should notice that the ModuleID for commissioned
modules, the ProgramID field and the IO model type (i.e. AO-4-8) are automatically
entered. This information was received from the module. Also, the Comm Status should
indicate an on-line status.

Commissioning a New I/O Module – Command Terminal

When you install a new I/O module onto the bus you must commission the unit before it
will operate properly. Follow the steps below to properly commission an I/O module using
the Command Terminal:

Remove power from the I/O Bus where the module is to be installed

Step 1 On the I/O Bus: Connect the IOU Module

Connect the IOU Module to the I/O Bus.
Step 2 On the I/O Bus: Restore Power
Restore power to the I/O Bus.
Step 3 From the Command Terminal: Create the IOU Module
Log onto a Command Terminal and create a new IOU Module (select Edit, then
IOU Modules, then enter a name for the new IOU Module).
Step 4 On the Command Terminal: Assign an IOU number to the Module
During the creation process, you assign a unique number to the module being
configured.
Step 5 If the module is not easily accessible: Enter the module ID into the
Module ID text field
Enter the module ID found on the label inside the cover of the module into the
field and TAB to the Save button and press ENTER, then skip to Step 8.
Step 6 If the module is easily accessible: TAB over to the Learn Button on the
Command Terminal
After creating the module and assigning the number, TAB over to the Learn
button and press ENTER. A dialog box displays requesting the operator to
press the Commission button on the physical module.
Step 7 On local Modules: Press the Commission button on the Module
Press the Commission button found on the front panel of the module. Clicking
this button sends information from the module to the Command Terminal.
When you push the Commission button, the dialog box should disappear
indicating that it received the information from the module.
Step 8 On the Command Terminal: Save the Form
When you save the form you should notice that the ModuleID for
commissioned modules, the ProgramID field and the IO model type (i.e. AO-4-
8) are automatically entered. This information was received from the module.
Also, the CommStatus should indicate an OnLine status.

28 Schneider Electric
Commissioning a Replacement I/O Module - CyberStation
When you replace an I/O module**, proceed as follows:

Remove power from the I/O Bus where the module is to be installed
Note: This procedure is for all modules except when replacing an AC-1 with an AC-1. For
that procedure, follow the instructions in the next section.

Step 1 Replace the module, re-apply power

Remove the old module, connect the new module in its place & re-apply
power.
Step 2 From CyberStation: Open the IOUModule Editor
Log onto a CyberStation and open the IOUModule editor of the IOU that is
being replaced.
Step 3 From CyberStation: Type in the new Module ID text field
Enter the module ID found on the label inside the cover of the new IOU
module into the field and click the Apply button.
Step 4 From CyberStation: Verify the new IOU Module is online
Click Refresh. You should notice that in the ModuleID field for the
commissioned module, the ProgramID field and the IO model type (i.e. AO-4-
8) are automatically entered. This information was received from the module.
Also, the Comm Status should indicate an on-line status.

Commissioning a Replacement I/O Module – Command Terminal

When you replace an I/O module**, proceed as follows:

Remove power from the I/O Bus where the module is to be installed
Note: This procedure is for all modules except when replacing an AC-1 with an AC-1
Plus. For that procedure, follow the instructions in the next section.

Step 1 Replace the module, re-apply power

Remove the old module, connect the new module in its place & re-apply
power.
Step 2 From the Command Terminal: Edit the IOU Module
Log onto a Command Terminal and edit the IOU Module (select Edit, then
IOU Modules, then press F2 to bring up the list of IOU Modules).
Step 3 From the Command Terminal: Enter the new module ID into the Module
ID text field
Enter the module ID found on the label inside the cover of the module into the
Module ID field and TAB over to the Save button then press ENTER.

Andover Continuum I/O System Reference 29

Step 4 From the Command Terminal: Verify the new IOU Module is online
Edit the IOU Module that was replaced (select Edit, then IOU Modules, then press F2 to
bring up a list of the IOU Modules, select from the list and press ENTER). You should
notice that the ModuleID field for the commissioned module, the ProgramID field and the
IO model type (i.e. AO-4-8) are automatically entered. This information was received from
the module. Also, the Comm Status should indicate an Online status.

Replacing an AC-1 with an AC-1 Plus Module - CyberStation

When you substitute an AC-1 Plus for an AC-1 module, proceed as follows:

Step 1 Place Cyberstation in OffLine Edit Mode

Step 2 Record the AC-1 IOU Number
Open the AC-1 module editor and note the module's ID (IOU field in the
editor)
Step 3 Close the AC-1 editor
Step 4 Delete the AC-1 module (still offline)
Remove power from the I/O Bus where the module is to be installed
Step 5 Replace the AC-1 with an AC-1 Plus
Physically remove the AC-1 and Replace with an AC-1 Plus and re-apply
power to the I/O Bus.
Step 6 Create a new IOU Module
Create a new IOU module through CyberStation Explorer (still offline) using
the same IOU Number as the AC-1 (NOTE: New IOU name DOES NOT
have to match old AC-1 name)
Step 7 Enter the new ModuleID
Enter the ModuleID of the new AC-1 Plus (ex: 00-03-63-27-61-00) into the
module ID field.
Step 8 Save the new AC-1 Plus module (click OK) and close the editor
Repeat steps 2 through 8 for all AC-1 to AC-1Plus replacements
Step 9 Place CyberStation back online
Step 10 Reload the controller
Step 11 Open, then close each AC-1 Plus Module editor
After reload is complete, open and close each AC-1 Plus module editor (this
step is necessary to relay some information from the controller to the
database)

Note: The AC-1 Plus has operational differences from AC-1 and AC-1A modules (i.e.
Degrade mode). Please refer to the AC-1, AC-1A and AC-1 Plus sections of this manual
for further information.

30 Schneider Electric
Replacing an AC-1 with an AC-1 Plus Module – Command Terminal
When you substitute an AC-1 Plus for an AC-1 module, proceed as follows:

Step 1 Record the AC-1 IOU Number

Open the AC-1 module editor and note the module's ID (IOU field in the
editor)
Step 2 Close the AC-1 module editor
Step 3 Open the door editor
Open the door editor for the door that is associated with the AC-1 to be
replaced and set the entry IOU (or exit IOU if appropriate) to 0 (zero).
Step 4 Save and close the door editor
Step 5 Delete the AC-1 module

Remove power from the I/O Bus where the module is to be installed

Step 6 Replace the AC-1 with an AC-1 Plus

Physically remove the AC-1 and Replace with an AC-1 Plus and re-apply
power to the I/O Bus.
Step 7 Create a new IOU Module
Create a new IOU module using the same IOU Number as the AC-1 (NOTE:
New IOU name DOES NOT have to match old AC-1 name)
Step 8 Learn the AC-1 Plus Module
Perform a Learn operation, or populate the Module ID field with the Module ID
of the new AC-1 Plus Module.
Step 9 Save the new AC-1 Plus module and close the editor
Step 10 Re-open the door object
Re-open the door object changed in Step 3 and restore the entry IOU (or exit
IOU if applicable) number, then save and close the door editor.

Andover Continuum I/O System Reference 31

Individual Module Wiring
This section of the document describes the various I/O modules and presents interfacing
information. Each module is presented in its own mini-section. The part number
designator for the module being described is printed on the outer edge of each page.

General Wiring Concerns for All Modules

Do not remotely ground any part of the input sensor wiring. Remote grounds connected
to the return terminal could make the system operate incorrectly or damage the
equipment. The signal return is not true earth ground. It is an electronic reference point
necessary to interpret the sensor properly.
It is recommended that you run input wiring in a conduit separate from AC power or
output wiring and avoid long wiring runs.
For reliable input operation, follow these input wiring guidelines:

• Never lay wires across the surface of a printed circuit board.

• Wires should never be within 1 in. or 25 mm of any component on a printed
circuit board.
• Use shielded input wire.
• Terminate the shield of the input wires at one end of the run only—preferably at
the end where your I/O module is located.
• Be careful when stripping wire not to drop small pieces of wire inside the cabinet.
• Don’t run your input wiring in the same conduit with AC power.
• Don’t run your input wiring in the same conduit with your output wiring.
• Don’t run high and low voltage wiring in the same conduit.
------------------------------------ IMPORTANT --------------------------------------
Grounding the Modules
All I/O modules except the VS-8 include a metal clip that is built into the locking
mechanism on the back of the case. Mounting the module on a metal surface or DIN rail
automatically provides an Earth ground. The VS-8 includes a ground stud that must be
connected to Earth ground. It is important that this connection be made as close to the
module as possible.

Caution
Do not externally ground any input signal connected to the module. This may
damage the unit. Signal return terminals are not connected to Earth Ground.

When installing Andover Continuum I/O modules it is imperative that the installer supply
a solid Earth ground connection to the pins provided.

32 Schneider Electric
 Electro Static Discharge (ESD) Warning
To avoid damaging electronic components due to the discharge of static
electricity, always ground yourself before touching any boards or other internal
components of Schneider Electric devices.

• At the very least, touch metal first.

• If possible, use a grounding strap or heel plate.

On each I/O module, the left-most pin is labeled with a ground symbol and
should have a short earth ground connection made to it. The wire should be as
short as possible, ideally 6 inches or less, and the wire gauge should be a
minimum of 18 AWG.

Earth Ground

Failure to install these grounds can result in controller resets or physical

damage to the CPU or I/O modules.

Later shipments of I/O Modules include a grounding clip built into the DIN Rail
clamp of the module. If the Din Rail itself is grounded you will no longer need to
ground the I/O modules. You will still need to ground the CPU Modules.

Andover Continuum I/O System Reference 33

 Limitations of Non-Volatile Memory
Flash memory devices used in our products are guaranteed for a minimum of 10,000
write operations. Flash memory is for storing completed configurations and a
snapshot of data at a particular time. When used in this manner, the memory should
last the lifetime of the product.

34 Schneider Electric
 UI-8-10

UI-8-10, UI-8-10-10V
Universal Input Modules
The UI-8-10, Andover Continuum’s universal input module, provides 8 universal inputs,
software configurable as voltage, thermistor, digital, or counter point types. Each point
can also be configured as a supervised input for security monitoring, providing indication
of on/off and trouble conditions. This module is a perfect choice for any mix of
temperature, pressure, flow, status points, and similar inputs in a control system, with a
0-5 volt input range and 10 bit A/D conversion.

The UI-8-10-10V model is available for 0–10V applications. It provides the identical point
type selection; but is equipped with individual voltage divider DIP switches on each input,
allowing each to be configured for a 0–10 volt range.

FEATURES

• 8 Universal Inputs

• 10 bit Resolution

• 0–5V or 0–10V Input Range

• Supports Voltage, Thermistor,

Digital, Counter and Supervised
Electrical Types

• Pull-up Resistor Disable Switches

• 10–28 V Power Supply Range

1

O
N
2

N
2
3

3
4

4
5

5
6

6
7

7
8

Andover Continuum I/O System Reference 35

UI-8-10

SPECIFICATIONS
ELECTRICAL
Power Supply Range: Input Voltage Range: 10-28V. 24V for UL864 and UL294
installations.
Power Consumption: 0.7 Watt (29 mA) @ 24VDC (max.); normally provided by Andover
Continuum power supply module.
Overload Protection: 0.5 A resettable fuse with transient voltage suppressor (TVS) and
reverse polarity protection.
INPUTS
Number of Inputs: 8 Universal inputs; 10 bit resolution
Input Types: Voltage, Thermistor, Digital, Counter, and Supervised
Input Protection: 24V AC/DC allowed to any single input
(40V transient voltage suppressor on each input – UI-8-10-10V)
Input Impedance: 5 MΩ w/pull-up disabled; 10 KΩ w/pull-up enabled – UI-8-10
(4.4 KΩ in 0-10V mode UI-8-10-10V)
Input Connections: Two-piece, 13-position removable terminal block

Voltage: UI-8-10 (0–5V) UI-8-10-10V (0–10V mode)

Range: 0–5 volts 0–10 volts
Resolution: 5 mV 10 mV
Accuracy: ±15 mV (±0.3% FSR) ±40 mV (±0.4% FSR)
Filtering: Corner Frequency at 15 Hz, –20 db/decade
Calibration: Permanent (factory)

Thermistor:
Type: 10 KΩ, Type III Thermistor
Range: -30 to 230°F
(-34 to 110°C)
Resolution: 40 to 100°F range 0.20°F typical
(4 to 38°C) (0.11°C typical)
Accuracy: 40 to 100°F range ± 1.0°F (includes 0.36° error for thermistor)
(4 to 38°C) (±0.55°C)

Digital & Counter:

Input Type: Contact Closure
Frequency: 4 Hz max.
Pulse Width: 125 ms min. (depends on scan time)

Supervised:
Input Type: Single or Double Resistor Supervision, Parallel or Series Circuit

36 Schneider Electric
 UI-8-10

I/O Connections
The actual input connections are located on a thirteen-position removable screw terminal
connector located at the bottom of the module.
The inputs are labeled IN1, IN2, IN3, and so forth. Each pair of inputs is followed by its
return connection labeled RET, resulting in a sequence of IN1, IN2, RET, IN3, IN4, RET,
and so on.
The connector allows for an Earth ground connection, eight inputs and four signal
returns.
The diagram screen printed on the module indicates where each input number is located
on the terminal block. These connections are also listed below.

Connection Description

Earth Ground
1. IN 1
2. IN 2
3. RETURN
4. IN 3
5. IN 4
6. RETURN
7. IN 5
8. IN 6
9. RETURN
10. IN 7
11. IN 8
12. RETURN
1

O
N
2

N
2
3

3
4

4
5

5
6

6
7

7
8

Andover Continuum I/O System Reference 37

UI-8-10

Input Circuitry
UI-8-10 Inputs are essentially voltmeters. Universal inputs can be configured through
software to become one of five different input circuits:

ƒ Temperature
ƒ Voltage
ƒ Digital
ƒ Counter
ƒ Supervised
During configuration, the value of the Electrical Type attribute you select tells the
controller how to interpret the reading from each input.
The following is a simplified schematic of both the UI-8-10 and the UI-8-10-10V Universal
inputs:

UI-8-10 UI-8-10-10V

The main difference between the two is the UI-8-10-10V circuit includes a switch
selectable front-end voltage divider that effectively divides the 10V input signal by two.
The proper switch settings for various modes of operation are listed on the front for the
module.

Note: Setting the reference resistor enable switch to ‘ON’ and setting the range to
‘10V’ is invalid.

38 Schneider Electric
 UI-8-10

Each input includes a low-pass filter after the pull-up formed by a series resistor and a
parallel capacitor. The resistor is utilized for over-voltage protection in limiting current to
two protection diodes (not shown). It is possible to have more than one input share a
single return wire. Keep in mind that the current through each input is approximately
0.3mA, so voltage drops occur with long runs of small gauge wire.

Pull-up Reference Resistor Selection Switches

In some measuring instances it is desirable that there be no pull-up resistor. Instead of
physically removing or cutting the resistor off the printed circuit board, the input module
includes a pull-up resistor selection switch for each input position. This switch allows you
to select whether or not you want a pull-up resistor in the circuit. A small 8-position switch
module is accessible from the front of the module when the door is opened.

These switch modules are commonly called “DIP Switches” and require a small object
such as the tip of a pen or a small screwdriver to operate them. Each switch position acts
as a “slide switch”. Pressing the raised slide marker to the side marked “on” closes or
enables the switch. To open or disable the switch position, press the slide marker over to
the “off” side.

Input Voltage Range Selection Switches (UI-8-10-10V Only)

Andover Continuum I/O System Reference 39
UI-8-10

The UI-8-10-10V module allows you to choose from two input voltage ranges. Selection
is accomplished by using a switch arrangement that is similar to the operation of the pull-
up resistor switches. This small 8-position switch module is located to the right of the pull-
up selector switch and is accessible from the front of the module when the door is
opened.

The Voltage Range switches allow you to select a range (0-5 V) or (0-10 V) for each
input.

The 0-5V range allows connections to signals that do not exceed 5.00V.

The 0-10V range allows connection to signals up to 10.00V. In this mode the circuit
actually uses the same input measuring circuit as the 0-5V range, however, it divides the
voltage present by two thereby limiting the internal circuitry to 0-5V. When you read a 0-
10V input the actual reading will be 0-5V. You must adjust your readings for the higher
range via formula. This is accomplished by applying a conversion factor to the reading.
When creating a 10V InfinityInput, set the Conversion to ElecValue * 2.

When using the 10V mode be sure to set the Reference resistor switch to Off.

Note: Setting the Reference Resistor enable switch to ‘ON’ and setting the Range
to ‘10V’ is invalid. Switching to 10V inputs dramatically lowers the impedance of
the input to 4.4 KΩ.

40 Schneider Electric
 UI-8-10

Supervisory Inputs
UI-8 inputs may be connected as supervisory inputs. The following drawings depict the
three types of supervisory inputs that exist—three normally closed and three normally
open types.

Normally Closed Supervised Inputs

NC Series
With this type of input wiring, a resistor is placed in series with the input being monitored.
When the input contact presents a short circuit (normal closed position) the input is
assumed in a normal closed state, the circuit presents a reading of 10 K Ωs at the input.

Circuit Action Input Senses Condition

Switch Closed External Resistance Input contact Closed
Switch Opened Infinite Resistance Input contact Open
Wire Cut Infinite Resistance Input contact Open ‘Violation’
Input Shorted Zero Ωs Violation or error

When the input contact is opened, the circuit opens and an infinite resistance is
measured. If the wires to the input contact are cut it also appears as an “input contact
open” condition. In this case there would be an input contact open without a valid card
swipe or valid keypad entry resulting in an “input contact violation”. Shorting the input
causes a zero Ω resistance, which also results in an input contact violation.

When configuring for this type of contact select:

ElecType: Supervised
Resistor Type: NCSeries

Andover Continuum I/O System Reference 41

UI-8-10

Normally Closed Supervised Inputs

NC Series Parallel
With this type of input wiring, two external resistors are added to the input, one in series
and the other in parallel. When the input contact switch is closed (normal position) the
input contact is assumed to be closed. The circuit presents a reading composed of both
resistances in parallel that works out to be half the value of one of them (5 KΩ).

Circuit Action Input Senses Condition

Switch Closed External Resistance ÷ 2 Input contact Closed
Switch Opened External Resistance Input contact Open
Wire Cut Infinite Resistance Violation or error
Input Shorted Zero Ωs Violation or error

When the input contact is opened the switch opens and the value of the parallel resistor
is measured. If the wires to the input contact are cut it appears as an infinite resistance.
Shorting the input causes a zero Ω resistance. Both a short and an infinite resistance
(open) should result in an error condition.

When configuring for this type of contact select:

ElecType: Supervised
Resistor Type: NCSerPar

42 Schneider Electric
 UI-8-10

Normally Open Supervised Inputs

NO Series Parallel
With this type of input wiring, two external resistors are added to the input, one in series
and the other in parallel. When the input contact switch is open (normal position) the
input contact is assumed to be closed. The circuit reads the value of the parallel resistor.

Circuit Action Input Senses Condition

Switch Closed External Resistance ÷ 2 Input contact Open
Switch Opened External Resistance Input contact Closed
Wire Cut Infinite Resistance Violation or error
Input Shorted Zero Ωs Violation or error

When the input contact is opened the switch closes and a reading results that is
composed of both resistances in parallel that works out to be half the value of one of
them (5 KΩ). If the wires to the input contact are cut it appears as an infinite resistance.
Shorting the input causes a zero Ω resistance. Both a short and an infinite resistance
(open) should result in an error condition.

When configuring for this type of contact select:

ElecType: Supervised
Resistor Type: NOSeriPar

Andover Continuum I/O System Reference 43

UI-8-10

Wiring Door Switches

There are three supervisory inputs for door switches. The maximum length wire you may
use is 500 ft of #18 gauge wire (152 m of 1.0 mm2 wire) or 200 ft of #22 gauge wire (60
m of 0.35 mm2 wire).

Some switches have built-in resistors that facilitate Series Parallel connections as shown
below:

Switch with AUX

Built-In Resistor or
DOOR
or
REX

10 KΩ

RET

Wiring Motion Detectors

Motion detectors are devices that close a switch contact when motion is detected.

Wiring is similar to a normal input contact switch input, however, the motion sensor
requires an external power supply of 12 VDC or 24 VDC (UL listed under APHV). The
maximum length wire you should use is 500 ft of #18 gauge wire (152 m of 1.0 mm2 wire)
or 200 ft of #22 gauge wire (60 m of 0.35 mm2 wire).

The following shows a typical motion detector circuit:

44 Schneider Electric
 UI-8-10

Measuring Temperature
UI-8-10 inputs can be configured to sense temperature by configuring one of the
module’s inputs appropriately. This is done by setting the Electrical Type to either ACC
Temp (DEG F) or ACC Temp (DEG C). Connect a resistive thermistor sensor to that
input terminal. The following is a schematic representation of the connection:

IN x

Thermistor

RET

One lead connects to a numbered input terminal, the other to a return terminal.
To use the input for temperature sensing, the pull-up reference resistor must be
connected into the circuit, therefore, the reference resistor switch for this input must
be placed in the “on” position and the Range switch must be in the 5V position.
When the input point is configured as a temperature input, the controller utilizes a look-up
table to convert from a voltage reading to a temperature reading in degrees Fahrenheit or
Celsius.

Caution
Never apply voltage to a thermistor—doing so alters the thermistor’s accuracy and
reliability. In fact, it’s a good idea to replace any thermistor that has had any sort of
voltage applied to it.

Maximum Wire Runs for Thermistors

To keep thermistor errors to a minimum, limit the length of wire runs to the maximum for
the gauge wire you select.

The following two pages include three tables that indicate the maximum length runs for
wires of various gauges to keep errors within certain temperature limits when using
thermistor elements.

Andover Continuum I/O System Reference 45

UI-8-10
Wire Gauges and Corresponding Maximum Runs for
Sensing Temperatures Up to 70 °F (21 °C)
Gauge 1/2 °F (.28 °C) Error 1/4 °F (.14 °C) Error 1/10 °F (.06 °C) Error

#14 26,700 ft. 13,300 ft. 5,300 ft.

2.5 mm2 8150 m 4000 m 1600 m
#16 16,700 ft. 8,300 ft. 3,300 ft.
1.5 mm2 5120 m 2500 m 1000 m
#18 10,500 ft. 5,200 ft. 2,100 ft.
1.0 mm2 3200 m 1600 m 640 m
#20 6600 ft. 3,300 ft. 1,300 ft.
0.5 mm2 2000 m 1000 m 400 m
#22 4,100 ft. 2,000 ft. 800 ft.
0.35 mm2 1250 m 600 m 250 m

Wire Gauges and Corresponding Maximum Runs for

Sensing Temperatures Up to 100 °F (38 °C)

Gauge 1/2 °F (.28 °C) Error 1/4 °F (.14 °C) Error 1/10 °F (.06 °C) Error

#14 12,600 ft. 6,300 ft. 2,500 ft.

2.5 mm2 3800 m 1900 m 760 m
#16 7,900 ft. 3,900 ft. 1,500 ft.
1.5 mm2 2400 m 1200 m 450 m
#18 5,000 ft. 2,500 ft. 1,000 ft.
1.0 mm2 1500 m 760 m 300 m
#20 3,100 ft. 1,500 ft. 600 ft.
0.5 mm2 950 m 450 m 180 m
#22 1,900 ft. 900 ft. 300 ft.
0.35 mm2 580 m 275 m 90 m

Wire Gauges and Corresponding Maximum Runs for

Sensing Temperatures Up to 150 °F (65 °C)

Gauge 1/2 °F (.28 °C) Error 1/4 °F (.14 °C) Error 1/10 °F (.06 °C) Error

#14 4,100 ft. 2,000 ft. 800 ft.

2.5 mm2 1250 m 600 m 240 m
#16 2,600 ft. 1,300 ft. 500 ft.
1.5 mm2 800 m 400 m 150 m
#18 1,600 ft. 800 ft. 300 ft.
1.0 mm2 500 m 240 m 90 m
#20 1,000 ft. 500 ft. 200 ft.
0.5 mm2 300 m 150 m 60 m
#22 600 ft. 300 ft. 100 ft.
0.35 mm2 180 m 90 m 30 m

46 Schneider Electric
 UI-8-10

Measuring DC Voltages
The UI-8-10 inputs may be configured to sense DC voltage by connecting the input
terminals to a DC voltage source within the range of the module’s input specifications.
The following is a schematic representation of the connection:

+ IN x

V
-
RET

The plus lead connects to the numbered input terminal, the other to a return terminal.

When interfacing to a voltage output sensor, specific information on the transducer may
be required. The pull-up resistor of the input circuit will affect the output of the transducer.

10V Input Notes

Although the 10V input configuration allows you to measure a higher voltage, it is scaled
so that you still measure a value of 0-5V. You have to convert the reading in your
conversion equation. When the input is configured for 10V operation, the input resistance
is 4.4kΩs. Therefore, the sensor would have to be able to source as much as 2.3mA.

When configuring either type of voltage input, select:

ElecType: Voltage
Reference Resistor OFF

Andover Continuum I/O System Reference 47

UI-8-10

Voltage Dividers
There are instances when it is necessary to interface to a voltage source that is higher
than the input range of the module. In these cases a voltage divider is necessary.

External DC input Voltage Divider

Two resistor values set up a ratio of voltage drop. These resistors must be sized
appropriately (value and wattage) for the source being monitored. The higher the
resistance values, the less loading effect there will be on the source.

The circuit shown above is a simple two-resistor voltage divider connected to one of the
UI-8-10 module’s inputs. The input circuitry of the module can measure a maximum of
either 5 Volts or 10 Volts (UI-8-10-10V only). Therefore, the voltage measured across the
reference resistor must not exceed this maximum.

In this case, be sure to switch the pull-up resistor out of the circuit.

48 Schneider Electric
 UI-8-10
Assuming you know the maximum voltage reading you are trying to measure (Vsource),
perform the following steps to determine the resistance values necessary to condition the
input for the module. If you have the UI-8-10-10V model, set the Range switch to 5V.
1. First, determine the current that will flow through the divider. Pick a value that your
source can supply. Let’s say 20 mA. This value will be represented by the variable
Itotal in the following equations.

2. Determine the total resistance value required of the entire divider (R1 + R2) to create
20mA given the source voltage by solving the following:
Rtotal = Vsource
Itotal

Example: if you are measuring a source that can supply 0- 30 V:

Rtotal = 30 V
20 mA

Rtotal = 30 V
.02 A
Rtotal = 1500 Ω

The current is constant through the two resistors. Knowing this and the fact that our input
can’t exceed 5V can determine the value of the resistor labeled R2.
3. Determine the value of R2 by solving the following:
R2 = Vinput
Itotal

R2 = 5 V
.02 A

R2 = 250 Ω

Through subtraction, you can determine the remaining resistor value:

Rtotal = R1 + R2
R1 = 1500 Ω - 250 Ω
R1 = 1250 Ω

Andover Continuum I/O System Reference 49

UI-8-10

Sensing Contact Closures (Digital)

Digital input points are designed to allow the monitoring of contact closures across an
input (contact wired between the input and return).

IN x

Contact
Closure

RET

Note: When configuring a Digital point, there is a “Polarity” attribute. If this attribute is
enabled, readings are reversed: “On” will occur when the contact is open, and “Off”
occurs when the contact is closed.

When configuring this type of input, select:

ElecType: Digital
Reference Resistor ON

50 Schneider Electric
 UI-8-10

Counting Pulsing Signals or Contact Closures

Counter inputs are designed to allow the monitoring of digital pulse trains or contact
closures across an input just like digital inputs, but they accumulate a total of those
closures and act like a counter.

When using an input as a counter, you must take into account the frequency of the input
signal being counted. Universal inputs do not allow for very high speed contact counting.
This module allows counting up to a maximum of 4 Hz or 4 contact closures per second.

Minimum Pulse Width

The high period of the signal must be at least 125 milliseconds.

The low period of the signal must be at least 125 milliseconds.

When configuring this type of input, select:

ElecType: Counter
Reference Resistor ON

Andover Continuum I/O System Reference 51

UI-8-10

Status/Control Panel
Status Indicators
The UI-8-10 module includes a complete indicator status panel on the front of the
module.

This panel includes indicators reporting on the status of the following:

POWER This green indicator illuminates when DC power is applied through the
I/O Bus.
COMM This yellow indicator illuminates when data is transmitted from the
module to the NetController. In normal operation, data is only transmitted
when an input value changes.

This indicator will also flash periodically as the NetController checks the
I/O bus.
STATUS This red indicator is normally off. If it is always on or flashing at a fast
rate there is a problem with the module.

This indicator can be manually illuminated from the CyberStation

workstation or Command Terminal Interface and used as a
troubleshooting aid when locating a particular module.

This panel also includes two operator switches that perform the following:

COMMISSION After physical installation and during configuration through the

CyberStation workstation or Command Terminal Interface, pressing this
button registers the module’s address with the system. For more
information, refer to the section on Module Configuration found earlier in
this manual.
RESET If the module becomes inoperable, pressing this button resets the
module. It does not erase its memory.

52 Schneider Electric
 DI-6-AC

DI-6-AC, DI-6-AC-HV
Digital AC Input Modules
The DI-6-AC, Andover Continuum’s digital AC input module, has six digital (“wet”) AC
inputs for cost-effective ON-OFF status indication of fan motor starters, solenoid valves,
control relays, or external power supplies, and similar applications that require a quick
and easy way to detect voltage. The DI-6-AC monitors the absence or presence of AC
voltage levels directly, with no interposing relays needed.

The DI-6-AC can monitor voltages from 20–132V. A DI-6-AC-HV model is also available
for sensing higher voltages (90–250V). Both models can also accept DC voltages. All
inputs are optically coupled with 2500V isolation on each input for noise-free operation.

FEATURES

• 6 optically-coupled, digital AC input

channels

• Independently Mounted

• Will accept AC or DC inputs

• 20–132V AC Input Range

(DI-6-AC)
90–250V AC Input Range
(DI-6-AC-HV)

Andover Continuum I/O System Reference 53

DI-6-AC

SPECIFICATIONS
ELECTRICAL
Power Supply Range: Input Voltage Range: 20-26V.
Power Consumption: 0.7 Watt (29 mA) @ 24VDC (max.); normally provided by Andover
Continuum power supply module.
Overload Protection: 0.5 A resettable fuse with transient voltage suppressor (TVS) and
reverse polarity protection.
INPUTS
Number of Inputs: 6 digital AC voltage inputs
Input Protection: 2500V isolation on each input.
Each input has a 270V MOV.
Input Connections: Two-piece, 13-position removable terminal block

DI-6-AC DI-6-AC-HV
Input Range: 20–132 Vrms 90–250 Vrms
Input Current: 5 mA max. 2 mA max.

DI-6-AC DI-6-AC-HV
AC Voltage “ON” Threshold: 16 Vrms 75 Vrms
(Above this voltage is considered “ON”)

AC Voltage “OFF” Threshold: 8 Vrms 30 Vrms

(Below this voltage is considered “OFF”)

Input Resistance (±5%): 30 KΩ 200 KΩ

Maximum Turn ON Time: 20 mS 20 mS

Maximum Turn OFF Time: 60 mS 60 mS

DC Input Voltage Range: 20–132V 90–250V

Pulse Width: 125mS min. (depends on scan time)
DC Input Current: 5mA (max.) 2mA (max.)
DC Voltage “ON” Threshold: 20V 90V
(Above this voltage is considered “ON”)

DC Voltage “OFF” Threshold: 12V 45V

(Below this voltage is considered “OFF”)

EUROPEAN STANDARDS
European Multi-Purpose Control–Electronic
Type 1B–Micro Disconnect

54 Schneider Electric
 DI-6-AC

I/O Connections
The actual input connections are located on a thirteen-position removable screw terminal
connector located at the bottom of the module.
The inputs are labeled IN1, IN2, IN3, and so forth. Each pair of terminals corresponds to
one input. With both AC and DC signals there is no polarity to observe during connection.
The connector allows for an Earth ground connection, eight inputs and four signal
returns.
The diagram screen printed on the module indicates where each input number is located
on the terminal block. These connections are also listed below.

Connection Description

Earth Ground
1. IN 1
2. IN 1
3. IN 2
4. IN 2
5. IN 3
6. IN 3
7. IN 4
8. IN 4
9. IN 5
10. IN 5
11. IN 6
12. IN 6

Andover Continuum I/O System Reference 55

DI-6-AC

Input Circuitry

The following is a simplified schematic of both the DI-6-AC and the DI-6-AC-HV Digital
Input module:

AC
15K OptoCoupler
IN x
AC to DC
Converter II
275V
MOV
10V
RET 15K

DI-6-AC

AC
100K OptoCoupler
IN x
AC to DC
Converter II
275V
MOV
40V
RET 100K

DI-6-AC-HV

The main difference between the two is the DI-6-AC-HV circuit includes a front end that
supports the higher voltages.

56 Schneider Electric
 DI-6-AC
Sensing AC or DC Digital Inputs
Digital input points are designed to provide an ON or OFF reading of a signal. Normally
you would associate an AC or DC voltage input with a value measurement, however, the
DI-6 modules include a voltage level trigger that senses the presence of a range of
voltages and converts those readings to ON and OFF indications.

AC Polarity DC
Signal IN x Independent Signal IN x

The determination of ON or OFF is based upon the following measurement thresholds:

DI-6-AC DI-6-AC-HV
AC Voltage “ON” Threshold: 16 Vrms 75 Vrms
(Above this voltage is considered “ON”)

AC Voltage “OFF” Threshold: 8 Vrms 30 Vrms

(Below this voltage is considered “OFF”)

DC Voltage “ON” Threshold: 20V 90V

(Above this voltage is considered “ON”)

DC Voltage “OFF” Threshold: 12V 45V

(Below this voltage is considered “OFF”)

Note: When configuring a Digital point, there is a ‘Polarity’ attribute. If this attribute is
enabled, readings are reversed: ‘ON’ will occur when the input is at the normal OFF
threshold. OFF occurs at the normal ON threshold.
When configuring either type of input, select:

ElecType: Digital

Andover Continuum I/O System Reference 57

DI-6-AC

Status/Control Panel
Status Indicators
The DI-6-AC module includes a complete indicator status panel on the front of the
module.

This panel includes indicators reporting on the status of the following:

POWER This green indicator illuminates when DC power is applied through the
I/O Bus.
COMM This yellow indicator illuminates when data is transmitted from the
module to the NetController. In normal operation, data is only transmitted
when an input value changes.

This indicator will also flash periodically as the NetController checks the
I/O bus.
STATUS This red indicator is normally off. If it is always on or flashing at a fast
rate there is a problem with the module.

This indicator can be manually illuminated from the CyberStation

workstation or Command Terminal and used as a troubleshooting aid
when locating a particular module.
INPUT These red indicators (one for each channel) illuminate when an ‘ON’
condition is sensed.

58 Schneider Electric
 DI-6-AC

This panel also includes two operator switches that perform the following:

COMMISSION After physical installation and during configuration through CyberStation

or Command Terminal, pressing this button registers the module’s
address with the system. For more information, refer to the section on
Module Configuration found earlier in this manual.
RESET If the module becomes inoperable, pressing this button resets the
module. It does not erase its memory.

Andover Continuum I/O System Reference 59

DI-8

DI-8
Digital Input Module
The DI-8, Andover Continuum’s digital input module, is used for cost-effective sensing of
multiple dry digital inputs in applications such as equipment status monitoring or alarm
point monitoring. The DI-8 has eight digital inputs⎯each can be software configured to
accept a digital (contact closure or 0–5 volt input) or counter signal. Counter frequency is
10Hz on all eight inputs. In addition, high speed counting up to 10KHz max. is available
(via a DIP switch) on Channels 1 and 2 for high-speed metering and industrial
applications.

40V transient suppressors on all eight inputs protect against high voltage short duration
transients events. The DI-8 is designed to accept dry contact inputs or 0-5 volts and can
withstand up to 24 VAC/DC continuous voltage on four channels.

FEATURES

• Allows interface to relay contact

closures or 0–5v digital signals.

• Allows high speed counting on

channels 1 and 2.

• Input protection allows accidental

wiring of 24VAC to inputs.

• 10–28 V Power Supply Range

60 Schneider Electric
 DI-8

SPECIFICATIONS
ELECTRICAL
Power Supply Range: Input Voltage Range: 10-28V. 24V for UL864 and UL294
installations.
Power Consumption: 0.8 Watt (33 mA) @ 24VDC (max.); normally provided by Andover
Continuum power supply module.
Overload Protection: 0.5 A resettable fuse with transient voltage suppressor (TVS) and
reverse polarity protection.
INPUTS
Number of Inputs: 8 digital inputs
Input Types: Digital or Counter, software selectable
Input Protection: 24V AC/DC applied to 4 channels max.
(40V transient protection on each input)
Input Impedance: 10 KΩ pull-up resistor referenced to +5V
Input Connections: Two-piece, 13-position removable terminal block

Digital:
Input Type: Contact closure or 0–5V input
Pulse Width: 50 ms minimum
Current: 0.5 mA

Counter:
Input Type: Contact closure or 0–5V input

Channels 1 and 2 in HI-speed mode:

Frequency: 10 kHz (max.)
Pulse Width: 50 µs (min.)
Current: 0.5 mA

Channels 3 through 8; and Channel 1 and 2 in LO-speed mode:

Frequency: 10Hz (max.)
Pulse Width: 50 ms (min.)
Current: 0.5mA

Andover Continuum I/O System Reference 61

DI-8

I/O Connections
The actual input connections are located on a thirteen-position removable screw terminal
connector located at the bottom of the module.
The inputs are labeled IN1, IN2, IN3, and so forth. Each pair of inputs is followed by its
return connection labeled RET.
The connector allows for an Earth ground connection, eight inputs and four signal
returns.
The diagram screen printed on the module indicates where each input number is located
on the terminal block. These connections are also listed below.

Connection Description

Earth Ground
1. IN 1
2. IN 2
3. RETURN
4. IN 3
5. IN 4
6. RETURN
7. IN 5
8. IN 6
9. RETURN
10. IN 7
11. IN 8
12. RETURN

62 Schneider Electric
 DI-8

High Speed Counter Selection Switches

The DI-8 input module allows input channels 1 and 2 to be configured with the capability
of counting input pulses or contact closures at a rate of up to 10 kHz. A selection switch
is included for each of these two input channels. This switch allows you to select whether
or not you want the high speed input connected. A small 2-position switch module is
accessible from the front of the module when the door is opened.

Slide marker
moves left and right

1 2
O N
These switch modules are commonly called “DIP Switches” and require a small object
such as the tip of a pen or a small screwdriver to operate them. Each switch position acts
as a “slide switch”. Pressing the raised slide marker to the left disables high speed
counting. To enable high speed counting, move the slide marker over to the right side.

Andover Continuum I/O System Reference 63

DI-8

Input Circuitry

The following is a simplified schematic of the DI-8 Digital Input module:

5V

10K
5V

IN x R
II

C
RET

Channels 1 and 2 can be configured to allow high speed counting. The switches on the
front of the module substitute different value components for the low pass filter formed by
the combination of R and C. These values support higher frequency inputs.

64 Schneider Electric
 DI-8

Sensing Digital Inputs or Contact Closures

Digital input points are designed to provide an ON or OFF reading of a signal (wired
between the input and return).

Digital logic IN x IN x
Signal
Contact
Closure

RET RET

A digital input is considered “ON” whenever the input senses a digital ‘low’ or a contact
closure. Similarly, an OFF condition is sensed with a logic ‘high’ or an open contact.

Note: When configuring a Digital point, there is a ‘Polarity’ attribute. If this attribute is
enabled, readings are reversed.

When configuring this type of input, select:

ElecType: Digital

Andover Continuum I/O System Reference 65

DI-8

Counting Pulsing Signals or Contact Closures

Counter inputs are designed to allow the monitoring of digital pulse trains or contact
closures across an input just like digital inputs, but they accumulate a total of those
closures and act like a counter.

When using an input as a counter, you must take into account the frequency of the input
signal being counted. Inputs 3–8 do not allow for very high speed contact counting.
These channels allow counting up to a maximum of 10 Hz or 10 contact closures or
digital pulses per second.

In high-speed mode, channels 1 and 2 can be configured (via front panel switch) to count
to a maximum of 10 kHz or 10,000 contact closures or digital pulses per second.

When configuring this type of input, select:

ElecType: Counter

66 Schneider Electric
 DI-8

Status/Control Panel
Status Indicators
The DI-8 module includes a complete indicator status panel on the front of the module.

This panel includes indicators reporting on the status of the following:

POWER This green indicator illuminates when DC power is applied through the
I/O Bus.
COMM This yellow indicator illuminates when data is transmitted from the
module to the NetController. In normal operation, data is only transmitted
when an input value changes.

This indicator will also flash periodically as the NetController checks the
I/O bus.
STATUS This red indicator is normally off. If it is always on or flashing at a fast
rate there is a problem with the module.

This indicator can be manually illuminated from the CyberStation

workstation or Command Terminal and used as a troubleshooting aid
when locating a particular module.
INPUT These red indicators (one for each channel) illuminate when an ‘ON’
condition is sensed.

Andover Continuum I/O System Reference 67

DI-8

This panel also includes two operator switches that perform the following:

COMMISSION After physical installation and during configuration through the

CyberStation workstation or Command Terminal, pressing this button
registers the module’s address with the system. For more information,
refer to the section on Module Configuration found earlier in this manual.
RESET If the module becomes inoperable, pressing this button resets the
module. It does not erase its memory.

68 Schneider Electric
 MI-6
MI-6
MilliAmp Input Module
The MI-6, Andover Continuum’s milliamp input module, allows for a direct connection of a
2-wire, loop powered, 0–20mA or 4–20mA sensor to any of the module’s six inputs. The
need for an external resistor and an external power supply are eliminated. The MI-6
module is a perfect match for temperature transmitters, humidity and pressure
transducers, gas monitors, and other industry-standard sensors with either a 0–20mA or
4–20mA output. The six inputs on the MI-6 module have a 0–20mA range and 10 bit A/D
conversion.

FEATURES

• 6 Current Measuring Inputs

• 0–20mA Range

• 10 Bit A/D Converter

Andover Continuum I/O System Reference 69

MI-6

SPECIFICATIONS
ELECTRICAL
Power Supply Range: Input Voltage Range: 20-26V. 24V for UL864 installations.
Power Consumption: 3.8 Watts (158 mA) @ 24VDC (max.); normally provided
by Andover Continuum power supply module (including up
to 20mA sensor power for each input).

Overload Protection: 0.5 A resettable fuse with transient voltage suppressor

(TVS) and reverse polarity protection.
INPUTS
Number of Inputs: 6 Milliamp inputs
Input Range: 0–20 mA
Resolution: 20 µA
Accuracy: ±80 µA max.
Drift: ±50 ppm/DegC (max.)
Input Resistance: 249 Ω, 0.1%
Maximum Input Current: ±30 mA
Voltage Supply to Sensors: 19.0–26.0V (varies with +24VDC input voltage)
Input Protection: Each input and the Sensor voltage output includes a
transient voltage suppressor (TVS) and a resettable fuse.
Input Connections: Two-piece, 13-position removable terminal block

70 Schneider Electric
 MI-6

I/O Connections
The actual input connections are located on a thirteen-position removable screw terminal
connector located at the bottom of the module.

The inputs are labeled IN1, IN2, IN3, and so forth. Each input occupies a pair of
terminals, resulting in a sequence of IN1+, IN1-, IN2+, IN2-, and so on. For any given
input, observe the polarity for that input, + connects to the Supply terminal of the input.
The minus terminal connects to the Signal input.

The diagram below indicates where each input number is located in the terminal block.

Connection Description

Earth Ground
1. IN 1 +
2. IN 1 -
3. IN 2 +
4. IN 2 -
5. IN 3 +
6. IN 3 -
7. IN 4 +
8. IN 4 -
9. IN 5 +
10. IN 5 -
11. IN 6 +
12. IN 6 -

Andover Continuum I/O System Reference 71

MI-6

Input Circuitry

The following is a simplified schematic of the MI-6 Milliamp Input module:

24V

300mA
Resettable
Fuse

5V

100mA
Resettable
Fuse R
To
Analog/Digital
Converter
249Ω C

All six input pairs include their own automatically resettable fuses. These devices are
designed to open when sensing an over-current. They reset when the current supplied is
within range.

Note: In some extreme instances, the fuses may require that you remove power to
the module temporarily to reset their state.

72 Schneider Electric
 MI-6

Sensing Current

The current supplying sensor is connected as indicated in the following illustration:

Supply

24V
Loop-Powered INx
Sensor
Signal

When configuring this type of input, select:

ElecType: ACC_InputCurrent

Andover Continuum I/O System Reference 73

MI-6

Status/Control Panel
Status Indicators
The MI-6 module includes a complete indicator status panel on the front of the module.

This panel includes indicators reporting on the status of the following:

POWER This green indicator illuminates when DC power is applied through the
I/O Bus.
COMM This yellow indicator illuminates when data is transmitted from the
module to the NetController. In normal operation, data is only transmitted
when an input value changes.

This indicator will also flash periodically as the NetController checks the
I/O bus.
STATUS This red indicator is normally off. If it is always on or flashing at a fast
rate, there is a problem with the module.

This indicator can be manually illuminated from CyberStation or

Command Terminal and used as a troubleshooting aid when locating a
particular module.
EXTERNAL
POWER This green indicator illuminates when 24V DC power is available to
external sensors.

74 Schneider Electric
 MI-6

This panel also includes two operator switches that perform the following:

COMMISSION After physical installation and during configuration through the

CyberStation workstation or Command Terminal, pressing this button
registers the module’s address with the system. For more information,
refer to the section on Module Configuration found earlier in this manual.
RESET If the module becomes inoperable, pressing this button resets the
module. It does not erase its memory.

Andover Continuum I/O System Reference 75

DM-20

DM-20
Digital Input/Output Module
The DM-20, Andover Continuum’s Digital Input and Output module, provides high
density, versatile I/O for many control applications. When coupled with the optional DIO-
20 Expansion Board, the DM-20 allows you to mix and match up to 20 digital inputs and
outputs. Using standard off-the-shelf digital I/O blocks, the DIO-20 allows the system to
meet a wide range of applications, including ON-OFF or pulse-width modulation (PWM)
control of equipment and for switching inductive loads up to 240 VAC. The DM-20
provides 24 VDC power to the DIO-20 via a separate cable assembly.

When used without the DIO-20 Expansion Board, the DM-20 can control any combination
of inputs and outputs, up to a total of 20 per module.

FEATURES

• 20 General Purpose Digital

Inputs/Outputs

• Each point can be configured as an

input or an output

• Direct connection to DIO-20

Expansion Module

76 Schneider Electric
 DM-20

SPECIFICATIONS
ELECTRICAL
Power Supply Range: Input Voltage Range: 20-26V. 24V for UL864 and UL294
installations.
Power Consumption: 0.5 Watts (20 mA) @ 24VDC (max.); provided by Andover
Continuum power supply module.
Up to 9 Watts (375 mA) @ 24VDC when the DIO-20 is
powered from the DM-20 .
External Power Connector: Three-position removable connector

Overload Protection: 0.5 A resettable fuse with transient voltage suppressor

(TVS) and reverse polarity protection for both DM-20 power
and DIO-20 power.

LED Power Supply: Customer-provided external 5V power supply when using

the DM-20 to drive LEDs. For smoke control applications,
Schneider Electric power supply:
PS 120/240 AC-25 (UL 864 listed) must be used.

INPUTS/OUTPUTS 20 total points; user-selectable channel-by-channel as

inputs or outputs
Inputs:
Input Type: w/DIO-20 w/o DIO-20
24 VDC logic voltage (DIO-20). 0–5 VDC
Input rating depends on input
module(s) selected.
Pulse Width: 125 ms (min.) 125 ms (min.)

Outputs:
Output Type: w/DIO-20 w/o DIO-20
5 VDC logic voltage. Open- collector Output
Range depends on output transistor with series
module selected. 330 Ω 1/8 W resistor;
5 VDC (max.), 15 mA

Output Resolution: 0.1 sec. For Pulse Width Modulation (PWM) control

Output Protection: Transient voltage suppressor (TVS) and current limiting

resistor on each channel.
I/O Connections: 25-position DB25 Female and one removable three-
terminal block.

Andover Continuum I/O System Reference 77

DM-20

I/O Connections
The actual I/O connections are located on a 25-position DB25-type female connector
located at the bottom of the module. A separate three-conductor removable screw
connector provides 24 VDC power to external devices.

The inputs are labeled I/O1, I/O2, I/O3, and so forth. Each input/output occupies a single
position of the connector. Five signal ground pins are supplied as well.

The diagram below indicates where each input number is located on the module.

3-Pin Connector
Connection Description

Earth Ground
1 + 24VDC @ .36 Amps
2 24 V Return

25-Pin D Connector
Connection Description
1. I/O 1
2. I/O 2
3. I/O 3
4. I/O 4
5. I/O 5
6. I/O 6
7. I/O 7
8. I/O 8
9. I/O 9
10. I/O 10
11. I/O 11
12. I/O 12
13. I/O 13
14. I/O 14
15. I/O 15
16. I/O 16
17. I/O 17
18. I/O 18
19. I/O 19
20. I/O 20
21. Ground
22. Ground
23. Ground
24. Ground
25. Ground
78 Schneider Electric
 DM-20

Input/Output Circuitry

The following is a simplified schematic of each DM-20 Input/Output channel:

+5V

330
I/O x
II

I/O Channel (same for all 20 channels)

All 20 I/O channels resemble the circuit shown above.

24V

500mA
Resettable
Fuse

The 24VDC power available to external devices includes an automatically resettable

fuse. This fuse is designed to open when an external device tries to extract more current
than is available. They reset when the current draw is back within range.

Note: In some extreme instances, the fuses may require that you remove power to
the module temporarily to reset their state.

Andover Continuum I/O System Reference 79

DM-20
Using the DM-20
The DM-20 is primarily designed to directly interface with the DIO-20. However, it can
also be used as a general purpose digital I/O module containing 20 points.

Note: Make sure that external devices are attached to the DM-20 before powering
the unit.

DIO-20 Interface
The DIO-20 Expansion Module provides a connection for up to 20* solid state input or
output modules for the I/O channels of the DM-20. It includes individually fused sockets
for modules from manufacturers such as Opto 22, Grayhill, Gordos, Crydom and Potter &
Brumfield. You can mix input and output modules on the DIO-20 as needed.

The connection between the DM-20 and the DIO-20 consists of a 25-pin ribbon cable to
supply data between the modules and a two-conductor power cable.

Data connection between the two is accomplished via a 25-pin male-male DB25 cable:

DM-20

DM-20 to DIO-20
Data Connection

DIO-20

*The actual number of modules supported depends on type and power used. Refer to the power requirements
on page 86.
.

80 Schneider Electric
 DM-20

The Power connection between the DIO-20 and the DM-20 is via a two-conductor cable
assembly as shown:

DM-20
D CONNECTOR

G G G G G
I/O I/O I/O I/O I/O I/O I/O N N N N N
14 15 16 17 18 19 20 D D D D D

24VDC @ .36 Amps

TO DI0-20

+ -
1 2
I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O
1 2 3 4 5 6 7 8 9 10 11 12 13 DM-20 to DIO-20
DC Power Connection

+24 V Return

+24 VDC

DIO-20

Using the DM-20/DIO-20 Combination

The DIO-20 provides the DM-20 with a real-world interface to its I/O channels. Solid-state
input modules (on the DIO-20) provide interface circuitry to a variety of signals. These
modules convert their signals to digital levels for input to the DM-20.
Similarly, solid-state output modules (on the DIO-20) allow the digital levels of the DM-20
to interface to a variety of signals.
In both cases, the I/O points are set up to have an Electrical Type of Digital no matter
what type of solid-state module is installed.

Andover Continuum I/O System Reference 81

DM-20

General Purpose DM-20 Digital Interface

The DM-20 can be used to provide 20* general purpose digital inputs and outputs. It is
not necessary to interface the module with an external expansion product to use its
capabilities. Each channel can be used to output a digital signal or read a digital signal or
contact closure.
The DM-20 can be configured as a general purpose digital input. With the addition of an
external reference pull-up resistor, it can be used for sensing contact closures or digital
logic signals as shown below:
5V

10K

Digital logic I/O x I/O x

Signal
Contact
Closure

GROUND GROUND

As a digital output, the DM-20 has an open collector output with a 330 Ω series resistor.
Connect digital devices and LED indicators as shown below:
5V +5V

10K

LED
Indicator
Digital logic I/O x I/O x
Input

GROUND GROUND

When configuring any of these inputs/outputs, select:

ElecType: Digital

* The actual number of modules supported depends on type and power used. Refer to the power requirements
on the following page.

82 Schneider Electric
 DM-20

Loss of Power / Communication

Output Restore Time

When power is lost to the module, all outputs turn off. This also occurs when the module
has lost communication with the NetController for more than 255 seconds.

When power is finally restored, the module can immediately restore the last state of the
outputs or be delayed so that the NetController can update the state before energizing
them. This option is called Output Restore Time and its value can be set through a
Numeric.

The Output Restore Time numeric is configured as follows:

Function Channel Object Type Direction Values

Output Restore Time 21 Numeric IOOutput Number of seconds to

wait before restoring
output state:
0–255

If the Output Restore Time numeric is not defined, the output will restore immediately
upon return of I/O power.
NOTE: Pulsed values are "saved" and will occur in their entirety after delay.

DM-20/DIO-20 Module Power Requirements

The DM-20 includes the ability to directly power a DIO-20 module. DIO-20 modules
support a combination of up to 20 input and output modules. The following details the
power requirements of each combination. This information is presented to determine the
power supply requirements for the board.

• Input modules consume a maximum current in their ON state of 23mA. The DM-
20 can only supply enough power for 14 input modules.
• Output modules consume a maximum current in their ON state of 16mA.
• The DIO-20 itself without any modules installed draws 20mA.

The DM-20 provides a total of 360mA for the DIO-20. Using the numbers supplied above
you can calculate how many modules are allowed.

Examples:
Up to 14 input modules: (14 x 23mA) + 20mA = 342mA
A total of 14 input modules exhausts (with only 18mA remaining) the current capability of the DM-20.
Up to 20 output modules:(20 x 16mA) + 20mA = 340mA
A total of 20 output modules consumes only 340mA from the DM-20.

Andover Continuum I/O System Reference 83

DM-20

Status/Control Panel
Status Indicators
The DM-20 module includes a complete indicator status panel on the front of the module.

This panel includes indicators reporting on the status of the following:

POWER This green indicator illuminates when DC power is applied through the
I/O Bus.
COMM This yellow indicator illuminates when data is transmitted from the
module to the NetController. In normal operation, data is only transmitted
when an input value changes.

This indicator will also flash periodically as the NetController checks the
I/O bus.
STATUS This red indicator is normally off. If it is always on or flashing at a fast
rate, there is a problem with the module.

This indicator can be manually illuminated from CyberStation or

Command Terminal and used as a troubleshooting aid when locating a
particular module.

84 Schneider Electric
 DM-20

This panel also includes two operator switches that perform the following:

COMMISSION After physical installation and during configuration through the

CyberStation workstation or Command Terminal, pressing this button
registers the module’s address with the system. For more information,
refer to the section on Module Configuration found earlier in this manual.
RESET If the module becomes inoperable, pressing this button resets the
module. It does not erase its memory.

Andover Continuum I/O System Reference 85

AO-4-8

AO-4-8, AO-4-8-O
Analog Output Modules
The AO-4-8, Andover Continuum’s analog output module, has four analog outputs with
eight-bit resolution, which can be configured as either voltage (0-10 VDC) or current (0-
20 mA) outputs. The AO-4-8 is the perfect choice for valves, dampers, variable speed
drives, and similar equipment that demand high control accuracy.

An AO-4-8-O model with full override capabilities is also available. Each output contains
a three-position manual override switch and override potentiometer. In addition, the AO-
4-8-O provides software override feedback to the Plain English programming language
for each output.

FEATURES

• 4 Analog Outputs
• 8 bit Resolution
• 0–10V Voltage Outputs
• 0–20mA Current Outputs
AO-4-8-O Only:
• Override Toggle Switches and
Potentiometers
• Override Detection

86 Schneider Electric
 AO-4-8

SPECIFICATIONS
ELECTRICAL
Power Supply Range: Input Voltage Range: 20-26V. 24V for UL864 installations.
Power Consumption: 3.8 Watts (158 mA) @ 24VDC (max.); normally provided
by Andover Continuum power supply module.

Overload Protection: 0.5 A resettable fuse with transient voltage suppressor

(TVS) and reverse polarity protection.

OUTPUTS
AO-4-8: 4 analog outputs; 8 bit resolution
AO-4-8-O: 4 analog outputs with overrides; 8 bit resolution

Output Protection: 1/8 pico fuse per channel (40V TVS on each output⎯AO-4-
8-O model only)
Output Connections: Two-piece, 13-position removable terminal block

Output Types: Voltage or current

Voltage:
Range: 0–10 V
Resolution: 0.05 V
Accuracy: ±0.10V (1%FSR)
Output Current: +5 mA (sourcing) -1 mA (sinking)
Load Resistance: 2 KΩ min.(sourcing)

Current:
Range: 0–20 mA
Resolution: 0.1 mA
Accuracy: ±0.2 mA
Load Resistance: 650Ω (max.)

Output Overrides: 3-position manual override switch and override

(AO-4-8-O only) potentiometer on each output, with software feedback. LED
override status indicator.
Output Connections: Two-piece, 13-position removable terminal block

Andover Continuum I/O System Reference 87

AO-4-8

I/O Connections
The actual output connections are located on a thirteen-position removable screw
terminal connector located at the bottom of the module.
The outputs are labeled OUT1 I, OUT1 V, OUT1 GND, and so forth. Each output
presents two ways of connecting, resulting in a current output between OUT1 I and OUT1
GND, and a voltage output between OUT1 V and OUT1 GND.
The connector allows for an Earth ground connection, eight inputs and four signal
returns.
The diagram screen printed on the module indicates where each input number is located
on the terminal block. These connections are also listed below.

Connection Description

Earth Ground
1. OUT1 I
2. OUT1 V
3. OUT1 GND
4. OUT2 I
5. OUT2 V
6. OUT2 GND
7. OUT3 I
8. OUT3 V
9. OUT3 GND
10. OUT4 I
11. OUT4 V
12. OUT4 GND

88 Schneider Electric
 AO-4-8

Output Circuitry

The following is a simplified schematic of each AO-4-8 Output channel:

24V

125mA
Pico
OUTx V Fuse
Digital to Analog
Converter

24V

125mA
Pico
OUTx I Fuse
Voltage to Current
Converter

GND

All 4 channels resemble the circuit shown above.

Andover Continuum I/O System Reference 89

 AO-4-8

Override Controls
The AO-4-8-O model includes an output override switch and manual variable
control for each output.

MANUAL

OFF

AUTO

ADJUST

The following describes the actions associated with each position of the override
controls:

MANUAL The analog signal generated by the module is controlled

manually by adjusting the ADJUST potentiometer below to the
manual override switch. Programs have no effect on the output
when the switch is in this position.

OFF The output is set to zero volts, zero mA. Programs and the
setting on the ADJUST potentiometer have no effect on the
output Device when the switch is in this position.

AUTO The analog signal is generated as a direct result of program

control. The setting on the ADJUST potentiometer has no effect
on the output Device when the switch is in this position.

ADJUST This is a variable control that allows you to manually adjust the
output of the analog signal when the override switch is in the
MANUAL position. Insert the tip of a small screwdriver to use this
control. Turning to the right (clockwise) increases the output.
Turning left (counterclockwise) decreases the output.

90 Schneider Electric
 AO-4-8

Voltage Output
The voltage output is a ground-referenced signal with a range of 0–10 VDC. The
maximum output current is 5 mA (2,000 s minimum resistance). Ensure that the device
being connected is either floating or at the same ground potential as the controller.
Connect the device across the following terminals:

OUTx I

OUTx V
Device
Load ≥ 2KΩ
Resistance
GND

NOTE: The load resistance (of the external device) must be greater than or equal to 2KΩ.

When configuring this type of output, select:

ElecType: Voltage

Andover Continuum I/O System Reference 91

 AO-4-8

Current Output
The current output is a current-sourcing, ground referenced circuit. This output can
source 0 - 20 mA with a maximum load impedance of 650 s.
Connect the device across the following terminals:

OUTx I

Device
Load
Resistance OUTx V
≤ 650Ω

GND

NOTE: The load resistance (of the external device) must be less than or equal
to 650 Ω.

When configuring this type of output, select:

ElecType: Current

92 Schneider Electric
 AO-4-8

Status/Control Panel
Status Indicators
The AO-4-8 module includes a complete indicator status panel on the front of the module.

This panel includes indicators reporting on the status of the following:

POWER This green indicator illuminates when DC power is applied through the
I/O Bus.
COMM This yellow indicator illuminates when data is transmitted from the
module to the NetController. In normal operation, data is only transmitted
when an input value changes.

This indicator will also flash periodically as the NetController checks the
I/O bus.
STATUS This red indicator is normally off. If it is always on or flashing at a fast
rate, there is a problem with the module.

This indicator can be manually illuminated from the CyberStation

workstation or Command Terminal and used as a troubleshooting aid
when locating a particular module.
OVERRIDE This red indicator illuminates whenever any of the override switches is in
a position other than AUTO.

Andover Continuum I/O System Reference 93

 AO-4-8

This panel also includes two operator switches that perform the following:

COMMISSION After physical installation and during configuration through the

CyberStation workstation or Command Terminal, pressing this button
registers the module’s address with the system. For more information,
refer to the section on Module Configuration found earlier in this manual.
RESET If the module becomes inoperable, pressing this button resets the
module. It does not erase its memory.

94 Schneider Electric
 DO-4-R

DO-4-R, DO-4-R-O
Digital Output Module
The DO-4-R, Andover Continuum’s digital output module, has four Form C relay outputs,
rated at 5 Amps @240 VAC. These versatile outputs make the DO-4-R an excellent
choice for switching motor starters and other inductive loads up to 240 VAC, with either
two position (on/off) or Pulse-Width Modulation (PWM) control. The PWM feature permits
the modulation of valves and dampers to 0.1 second resolution. Two adjacent Form C
relay outputs can be combined in software to provide a Tri-state output, for bi-directional
control of valves and dampers and other end devices. Metal oxide varistors and 5000V
isolation on each output ensure reliable noise-free operation.

A DO-4-R-O model with full override capabilities is also available. Each output has a local
hand-off-auto switch, which enables service personnel to override the output. The switch
also provides override feedback of output values for use in troubleshooting or test
conditions. A local indicator light for each output displays relay status. Another LED
provides override status.

FEATURES
• 4 Form C Relay Outputs
• 240 VAC @ 5A Contact Rating
• Independently Mounted
• Output Status LEDs
• 10–28 V Power Supply Range

DO-4-R-O Only:
• Override Toggle Switches
• Override Detection

Andover Continuum I/O System Reference 95

DO-4-R

SPECIFICATIONS
ELECTRICAL
Power Supply Range: (DO-4-R, DO-4-R-O): Input Voltage Range: 10-28V. 24V for
UL864 and UL294 installations.

Power Consumption: 2.8 Watts (116 mA) @ 24 VDC (max.); normally provided
by Andover Continuum power supply module.

Overload Protection: 0.5 A resettable fuse with transient voltage suppressor

(TVS) and reverse polarity protection.

OUTPUTS
DO-4-R: 4 Form C relay outputs
DO-4-R-O: 4 Form C relay outputs with overrides

Output Rating: 240 VAC @ 5 Amps; 30 VDC @ 5 Amps

Output Resolution: 0.1 sec. For Pulse Width Modulation (PWM) control

Output Protection: 270 V varistors across contacts.

5000 VRMS isolation @ 60 Hz between relay contacts and
relay coil.

DO-4-R-O
Output Overrides: 3-position manual override switch on each output, with
software feedback.
LED override status indicator

DO-4-R-O
Override Feedback: Override detection and feedback provided for each output.

Output Connections: Two-piece, 13-position removable terminal block

EUROPEAN STANDARDS
European Multi-Purpose Control–Electronic
Type 1B–Micro Disconnect

96 Schneider Electric
 DO-4-R

I/O Connections
The actual output connections are located on a thirteen-position removable screw
terminal connector located at the bottom of the module.
The outputs are labeled OUT 1 NC, OUT 1 NO, OUT 1 COM, and so forth. Each output
presents a single pole double throw set of contacts. OUT 1 NC is the normally closed
side of the contact. OUT 1 NO is the normally open contact. OUT 1 COM is the common
connection that represents the armature of the relay switch.
The diagram below indicates where each output number is located in the terminal block.

Connection Description

Earth Ground
1. OUT 1 NC
2. OUT 1 NO
3. OUT 1 COM
4. OUT 2 NC
5. OUT 2 NO
6. OUT 2 COM
7. OUT 3 NC
8. OUT 3 NO
9. OUT 3 COM
10. OUT 4 NC
11. OUT 4 NO
12. OUT 4 COM

Andover Continuum I/O System Reference 97

DO-4-R

Output Circuitry

The following is a simplified schematic of each Output channel:

OUT x NC

OUT x NO

OUT x COM

All 4 channels resemble the circuit shown above.

These output contacts operate as a standard relay. When the output is set to an “ON”
state, the normally open contacts (OUTx NO) close and the normally closed contacts
(OUTx NC) open.

To use the Form C output in your system, configure an output point with an Electrical
Type of Digital.

Supervising the Outputs for UL1076

To supervise the operation of the DO-4 outputs, install a remote relay in parallel with the
device being switched. The contacts of this relay are connected back to a UI-8
supervised input. A 10K EOL resistor is connected across the relay contacts. A Plain
English program containing the following line would be executed:

If (DO4_Output = On AND UI8_Input = Off) OR (UI8_Input = TROUBLE) THEN

DO4_Alarm = ON ELSE DO4_Alarm = OFF

If an open, short or grounded condition exists either on the cable out to the switched
device or the cable running back to the UI-8, an audio and visual alarm would be
triggered at the central receiving station when the output was turned on.
For 24 VDC Loads use relay: Potter & Brumfield (TYCO) KUP5D15 *
For 24 VAC loads use relay: Potter & Brumfield (TYCO) KUP5A15 *
*These relays are UL recognized components

98 Schneider Electric
 DO-4-R

Override Controls
The DO-4-R-O model includes an output override switch for each output.

ON

OFF

AUTO

The output of the module can be directed from program control to manual
control. The output can be disabled completely as well.

The following describes the actions associated with each position of the override
controls:
ON The output relay is energized to an “ON” state manually by
setting the switch to ON. Programs have no effect on the output
when the switch is in this position.
OFF The output relay is de-energized to an ‘OFF’ state manually by
setting the switch to OFF. Programs have no effect on the output
when the switch is in this position.
AUTO The action of the output relay is determined as a direct result of
program control.

Loss of Power / Communication: Output Restore Time

When power is lost to the module or it loses contact with the NetController for more than
255 seconds, all outputs turn off. When power is finally restored, the module can
immediately restore the last state of the outputs or be delayed so that the NetController
can update the state before energizing them. This option is called Output Restore Time
and its value can be set through a Numeric.

The Output Restore Time numeric is configured as follows:

Function Channel Object Type Direction Values

Output Restore Time 5 Numeric IOOutput Number of seconds to

wait before restoring
output state:
0–255

If the Output Restore Time numeric is not defined, the output will restore immediately
upon return of I/O power.

Andover Continuum I/O System Reference 99

DO-4-R

Tri-State Output
Although the module contains four separate form C relays, adjacent pairs of these can be
combined at any one time to form a standard Tri-state output:
OUT1 and OUT2
OUT3 and OUT4
Configure the output point of the first point (OUT1 or OUT3) with an Electrical Type of
Tri-state.

Caution: Do not attempt to use OUT2 and OUT3 as a tri-state pair. An error
message may result. Configure tri-state outputs as OUT1-OUT2 or OUT3-OUT4.

Connect the two outputs together as follows (example shows OUT1 and OUT2):

OUT 1 NC

OUT 1 NO
+ ON

OUT 1 COM
Common

OUT 2 NC
OFF

OUT 2 NO
ON

OUT 2 COM

100 Schneider Electric

 DO-4-R

Status/Control Panel
Status Indicators
All DO-4 models include a complete indicator status panel on the front of the module.

This panel includes indicators reporting on the status of the following:

POWER This green indicator illuminates when DC power is applied through the
I/O Bus.
COMM This yellow indicator illuminates when data is transmitted from the
module to the NetController. In normal operation, data is only transmitted
when an input value changes.

This indicator will also flash periodically as the NetController checks the
I/O bus.
OVERRIDE This red indicator illuminates whenever any of the override switches is in
a position other than AUTO. (operates on -O models only)
STATUS This red indicator is normally off. If it is always on or flashing at a fast
rate, there is a problem with the module.

This indicator can be manually illuminated from CyberStation or

Command Terminal and used as a troubleshooting aid when locating a
particular module.
OUTPUT These red indicators (one for each channel) illuminate when an output
relay is energized.

Andover Continuum I/O System Reference 101

DO-4-R

This panel also includes two operator switches that perform the following:

COMMISSION After physical installation and during configuration through CyberStation

or Command Terminal, pressing this button registers the module’s
address with the system. For more information, refer to the section on
Module Configuration found earlier in this manual.
RESET If the module becomes inoperable, pressing this button resets the
module. It does not erase its memory.

102 Schneider Electric

 DO-6-TR

DO-6-TR
Triac Output Module
The DO-6-TR, Andover Continuum’s triac output module, has six Form A triac-based
outputs, rated at 0.5 Amps @ 24 VAC, for cost-effective on/off or pulse-width modulation
(PWM) control of lighting, heat, and fan units. The PWM feature permits the modulation
of valves and dampers to 0.1 second resolution. Adjacent outputs can also be configured
in pairs to provide up to three Form K, Tri-state outputs for bi-directional control of
dampers and valves.

Metal Oxide Varistors (MOVs), Snubbers and Optocouplers on the DO-6-TR provide
2500 V isolation on each output, ensure noise-free operation, and, in most cases,
eliminate the need to install MOVs in the field.

FEATURES

• Six (6) Triac-based outputs

• 24 Vrms @ 0.5 A Contact Rating
• Output Status LEDs

Andover Continuum I/O System Reference 103

DO-6-TR

SPECIFICATIONS
ELECTRICAL
Power Supply Range: Input Voltage Range: 20-26V. 24V for UL864 installations.

Power Consumption: 1.1 Watts (45 mA) @ 24 VDC (max.); normally provided
by Andover Continuum power supply module.

Overload Protection: 0.5 A resettable fuse with Transient Voltage Suppressor

(TVS) and reverse polarity protection.

OUTPUTS
Output Type: 6 Form A optically isolated triac outputs (can be configured
up to 3 Form K Tri-State outputs)

Output Rating: 0.5A @ 24 VAC, (Cannot switch DC loads)

Output Accuracy: 0.1 sec. for Pulse Width Modulation (PWM) control

Output Protection: 2500 V optical isolation

MOV and Snubber on each output

Output Connections: Two-piece, 13-position removable terminal block

104 Schneider Electric

 DO-6-TR

I/O Connections
The actual output connections are located on a thirteen-position removable screw
terminal connector located at the bottom of the module.
The outputs are grouped in pairs of two connector terminals per channel. Each output
presents a normally open single pole set of contacts.
The diagram below indicates where each output number is located in the terminal block.

Connection Description

Earth Ground
1. OUT 1
2. OUT 1
3. OUT 2
4. OUT 2
5. OUT 3
6. OUT 3
7. OUT 4
8. OUT 4
9. OUT 5
10. OUT 5
11. OUT 6
12. OUT 6

Andover Continuum I/O System Reference 105

DO-6-TR

Output Circuitry

The following is a simplified schematic of each DO-6-TR Output channel:

OUT x

OUT x

All 6 channels resemble the circuit shown above.

These output contacts operate as a solid state relay. When the output is set to an “ON”
state, the contacts close allowing current to flow between the output terminals.

To use the Form A output in your system, configure an output point with an Electrical
Type of Digital.

Loss of Power / Communication: Output Restore Time

When power is lost to the module or it loses contact with the NetController for more than
255 seconds, all outputs turn off. When power is finally restored, the module can
immediately restore the last state of the outputs or be delayed so the NetController can
update the state before energizing them. This option is called Output Restore Time and
its value can be set through a Numeric.

The Output Restore Time numeric is configured as follows:

Function Channel Object Type Direction Values

Output Restore Time 7 Numeric IOOutput Number of seconds to

wait before restoring
output state:
0–255

If the Output Restore Time numeric is not defined, the output will restore immediately
upon return of I/O power.

106 Schneider Electric

 DO-6-TR

Switching Loads with Triacs

Although the Triac-based outputs of this module appear as relay contacts in the
schematics provided, they are actually solid-state switches that have limitations on the
loads they can switch.

AC vs. DC
The first limitation is that they cannot be used with DC loads. A Triac switches AC only.

Minimum Load Current

The second limitation involves the minimum load current. In order for the Triac to
switch, it must detect at least 30 mA of current from the load. If your load is less than
30 mA, you can induce the required load by connecting a resistor across the load (not
directly at the Triac!). Check the current draw specification on your field device, and if it
does not meet this minimum, add a resistor in parallel with the device being driven sized
to achieve the minimum loading. Use the following formulas to determine resistance and
wattage:

Resistance (Ωs) =Voltage Power (Watts) = (Voltage) 2

Current Resistance

Andover Continuum I/O System Reference 107

DO-6-TR

Tri-State Output
Although the module contains six separate form A relays, adjacent pairs of these can be
combined at any one time to form a standard Tri-state output:
OUT1 and OUT2
OUT3 and OUT4
OUT5 and OUT6
Configure the output point of the first point (OUT1, OUT3 or OUT5) with an Electrical
Type of Tri-state.

Caution: Do not attempt to use OUT2 and OUT3 or OUT4 and OUT5 as a tri-state pair.
An error message may result. Configure tri-state outputs as OUT1-OUT2, OUT3-OUT4 or
OUT5-OUT6.

Connect two outputs together to form a tristate output as follows (pair OUT1 and OUT2 is
shown):

OUT 1
+ ON

OUT 1

Common

OUT 2

OUT 2
ON

108 Schneider Electric

 DO-6-TR

Status/Control Panel
Status Indicators
The DO-6-TR module includes a complete indicator status panel on the front of the
module.

This panel includes indicators reporting on the status of the following:

POWER This green indicator illuminates when DC power is applied through the
I/O Bus.
COMM This yellow indicator illuminates when data is transmitted from the
module to the NetController. In normal operation, data is only transmitted
when an input value changes.

This indicator will also flash periodically as the NetController checks the
I/O bus.
STATUS This red indicator is normally off. If it is always on or flashing at a fast
rate, there is a problem with the module.

This indicator can be manually illuminated from the CyberStation

workstation or Command Terminal and used as a troubleshooting aid
when locating a particular module.
OUTPUT These red indicators (one for each channel) illuminate when a triac
output is ON.

Andover Continuum I/O System Reference 109

DO-6-TR

This panel also includes two operator switches that perform the following:

COMMISSION After physical installation and during configuration through the

CyberStation workstation or Command Terminal, pressing this button
registers the module’s address with the system. For more information,
refer to the section on Module Configuration found earlier in this manual.
RESET Should the module become inoperable, pressing this button resets the
module. It does not erase its memory.

110 Schneider Electric

 LO-2

LO-2, LO-2-O
Lighting Control Module
The LO-2, Andover Continuum’s lighting control module, can control 2 high voltage
lighting circuits, using externally mounted GE RR7 or RR9 lighting relays, rated for 277
VAC and 20 Amps (347 VAC option for Canada). The RR9 relay provides status
feedback of the relay position, using a built-in pilot contact. The RR7 relay provides
control of the circuit with no feedback. An on-board status LED for each output is
provided when RR9 relays are used, as well as pilot light voltage for wall switches that
have status indication. External 28 VAC is required to power the GE relays. This same
transformer can power the LO-2 when the module is located remotely.

An LO-2-O model, with on-board momentary override toggle switches, is also available.

FEATURES

• 2 Lighting Outputs

• Uses standard RR-7 or RR-9 relays

• External 28 VAC required to power

GE relays

• On-board logic powered by Andover

Continuum Power Supply or
External 28V transformer.
Therefore, when the LO-2 is
remotely located, it can be powered
by 28 VAC alone.

• Output Status LEDs

LO-2-O Only:
• Override Toggle Switches

Andover Continuum I/O System Reference 111

LO-2

SPECIFICATIONS
ELECTRICAL
Power Supply Range: Input Voltage Range: 20-26V.
Power Consumption: 0.4 Watts (16 mA) @ 24 VDC (max.); provided by
Andover Continuum power supply module. Consumes no
DC power when external AC power is present.

External AC Power: 28 VAC powers both the module and lighting relays; can
also power the LO-2 module when mounted remotely.
External Transformer Size: 40 VA transformer provides power for up to 5 LO-2
modules (10 GE relays and associated devices).

Overload Protection: DC: 0.5 A resettable fuse with transient voltage suppressor
(TVS) and reverse polarity protection.
AC: 0.5 A resettable fuse with MOV.

INPUTS/OUTPUTS
Inputs: 2 Class II Low Voltage override inputs, providing direct
control of lighting relays
Input Protection: Transient voltage suppressors (TVS) with reverse polarity
protection
Outputs:

Output Type: 2 pulsed lighting control outputs compatible with externally

mounted GE RR7 or RR9 relays
Output Rating: Lamp Load – 20 Amp Tungsten Filament @125 VAC
(Relay) Resistive Load – 20 Amp Ballast @ 277 VAC (20 amp
@347 VAC, Canada)
Motor Load – 0.5 Hp @ 110–125 VAC
0.5 HP @ 220–277 VAC (0.5 Hp @ 347 VAC, Canada)
Pilot Contact Rating (RR9 only): 1 Amp, 24 VAC, isolated
Output Feedback: RR9 relays have LED status indication and software
feedback for relay status

Output Protection: Transient voltage suppressors (TVS) on outputs. GE relays

provide isolation.
Overrides: Momentary override toggle switches (LO-2-O model only)

Power/Output Connections: Two-piece, 12-position removable terminal block

Lighting Relay Connections: 5-position male connector accepts standard GE female
plug-in connector.

112 Schneider Electric

 LO-2
I/O Connections
The actual I/O connections are located on a combination of a twelve-position removable
screw terminal connector located at the center of the module and two five-pin Molex relay
connectors at the bottom.

The diagram below indicates where each output number is located in the terminal block.

Connection Description

Earth Ground
1. GND for 24–30V Ext. Power
2. 24–30V External VAC
3. OUT 1 RED
4. OUT 1 BLK
5. OUT 1 YEL
6. OUT 1 WHT
7. OUT 2 RED
8. OUT 2 BLK
9. OUT 2 YEL
10. OUT 2 WHT
11. 24 VAC RECT

Andover Continuum I/O System Reference 113

LO-2

Electrical Description
The outputs of the LO-2 module are digital in nature (ON or OFF) yet are designed
specifically to control lighting. The two outputs are electrically connected (via cable) to an
external bracket where two GE-style lighting relays (RR-7 or RR-9) have been mounted.

Both outputs can be controlled via program or be activated manually through override
switches (LO-2-O only) on the front panel. An external momentary switch (a push button,
motion detector or other occupancy sensor) can be wired to control each of the relays as
well.

The GE relays mechanically latch in the ON position when energized. The relay remains
ON until set to OFF from the program or any external override controls. RR-9 relays also
provide operational status information (ON or OFF) that can be read via Plain English
commands. The OUTPUT indicators on the front panel illuminate if the RR-9 relay output
is ON.

Override Controls
The LO-2-O model includes a built-in output override switch for each output.

ON

OFF

The operation of the relays can be operated from program control or manual control
using the front panel mounted override switches or externally wired controls.

The following describes the actions associated with each position of the override controls:

ON The output relay is energized to an “ON” state manually by setting the

switch to ON. The spring-loaded momentary action of the switch moves
the switch back to the center position after pressing.

OFF The output relay is de-energized to an “OFF”’ state manually by setting

the switch to OFF. The spring-loaded momentary action of the switch
moves the switch back to the center position after pressing.

114 Schneider Electric

 LO-2

External Override Capabilities

Two Class II low voltage manual override inputs, one for each relay output, are provided
for override capabilities. These inputs directly control the lighting relays, independent of
any schedule or program. Wall switches, occupancy sensors, or a combination of both
may be wired to these inputs.

Lighting Control
The LO-2 can be coupled with Andover Continuum’s programmable input modules to
provide flexible lighting control strategies such as:

• Outdoor Lighting Control with a Photocell

• Daylight Control
• After-Hours Lighting Usage with Card Swipe Readers
• Adjustable Override Time with Flick Warning
• Cleaning Crew Override
• Data Logging and Reporting
• Run time Analysis, including Accumulated On-Time and Percentage On-Time
• Tenant Billing Reports
• Custom Control Strategies

These programs can be easily modified to fit the exact needs of your project.

Andover Continuum I/O System Reference 115

LO-2

Electrical Installation

External Power
The GE relays are powered by an external 28 VAC source. The LO-2 module has been
designed to utilize this external power source as its own module supply source as well. It
is not necessary to power the module in this way. However, if the LO-2 is located
remotely from your main power source, you may want to power the module locally
thereby eliminating the two extra wires necessary to bring power to the module from the
Andover Continuum power supply. It also lessens the load requirements on that supply.

28 VAC Relay Power

Connect the output of a 28 VAC transformer to the module power inputs as shown:

28 VAC
Transformer

PWR

24-30 VAC

GND

This ground connection must be

the same point as the ground
for the Continuum Power Supply

External Control Power

Externally mounted sensors such as proximity sensors require power to operate as well.
The LO-2 module provides a connection for these devices to receive half wave rectified
28 V power as indicated below:

28 VDC (half-wave rectified AC)

to External Sensors
28 VAC
RECT

116 Schneider Electric

 LO-2

Relays
The GE relays are mounted externally and are connected to the LO-2 via a connecting
cable. This cable terminates in a five-pin Molex-style connector that mates easily with
one of the two headers provided at the bottom of the module as shown below:

The connector is keyed so that it locks into place after insertion. The connector on the left
is output relay #1 and the one on the right is output relay #2. External relays are attached
to the provided cable by matching the colors to those attached to the relay.

The following indicates the connections for each pin of the relay connector:
1 2 3 4 5 1 2 3 4 5

1 Blue 24VAC Rectified

2 Red On
3 Black Off
4 Yellow * Pilot Contact Return
5 Yellow * Pilot Contact Source

* These connections only apply to the RR9 relay.

Andover Continuum I/O System Reference 117

LO-2

Wiring External Controls

The relays can each be controlled by external momentary switches or other momentary
device such as a proximity detector. Each relay contains a set of input connections for
the control. Connect the external control(s) as shown:

Mechanical Switch without Integral Indicator:

Momentary Switch

OFF ON
RED

BLK

OVERRIDE

YEL

WHT

Mechanical Switch with Integral Indicator:

Momentary Switch

OFF ON
RED

BLK

Indicator OVERRIDE

YEL

WHT

118 Schneider Electric

 LO-2

Controlling both Outputs with One Switch

RED

BLK

OVERRIDE

YEL

Momentary Switch WHT

OFF ON
RED

BLK

OVERRIDE

YEL

WHT

Andover Continuum I/O System Reference 119

LO-2

Occupancy Sensor Connection

RED (ON)
RED

BLK
BLK
(OFF)

Occupancy Sensor OVERRIDE

YEL

WHT
WHT
(COM)

BLU 28 VAC
(POWER) RECT.

Controlling both Outputs with One Occupancy Sensor

To control both relays with the same Occupancy sensor, simply wire the red and black
connections of each input bank together as indicated on the drawing on the previous page.

120 Schneider Electric

 LO-2

Status/Control Panel
Status Indicators
The LO-2 module includes a complete indicator status panel on the front of the module.

This panel includes indicators reporting on the status of the following:

POWER This green indicator illuminates when DC power is applied through the
I/O Bus.
COMM This yellow indicator illuminates when data is transmitted from the
module to the NetController. In normal operation, data is only transmitted
when an input value changes.

This indicator will also flash periodically as the NetController checks the
I/O bus.
STATUS This red indicator is normally off. If it is always on or flashing at a fast
rate, there is a problem with the module.

This indicator can be manually illuminated from CyberStation or

Command Terminal and used as a troubleshooting aid when locating a
particular module.
OUTPUT These red indicators (one for each channel) illuminate when an ‘ON’
condition is set. These indicators operate with RR-9 relays only.
28 VAC This green indicator illuminates when 24–30 VAC power is supplied to
the module by an external source.

Andover Continuum I/O System Reference 121

LO-2

This panel also includes two operator switches that perform the following:

COMMISSION After physical installation and during configuration through the

CyberStation workstation or Command Terminal, pressing this button
registers the module’s address with the system. For more information,
refer to the section on Module Configuration found earlier in this manual.
RESET If the module becomes inoperable, pressing this button resets the
module. It does not erase its memory.

122 Schneider Electric

 DIO-20

DIO-20
Input/Output Expansion Module
The DIO 20 provides a connection for up to 20 solid state input or output modules for the
Andover Continuum DM-20 Digital I/O module. The DIO 20 module can be mounted via a
DIN Rail or directly to a panel. The DIO 20 includes individually fused sockets for up to 20
solid state input/output modules from manufacturers such as Opto 22, Grayhill, Gordos,
Crydom and Potter & Brumfield.

FEATURES

• 20* General Purpose Digital

Inputs/Outputs

• Each point may be configured as an

input or an output

• Direct connection to DM-20 Expansion

Module

• *The actual number of modules that a DM-

20 can power depends on the mix of input
and outputs modules desired. Refer to the
DM-20/DIO-20 Power Requirements
section found on page 94.

Andover Continuum I/O System Reference 123

DIO-20

SPECIFICATIONS
ELECTRICAL
Power Supply Range: 24 VDC
Power Consumption: All input modules installed: 12.7 Watts (529 mA) max;
provided by an external power supply module.
All output modules installed: 8.5 Watts (354 mA) max;
provided by an external power supply module.
DIO-20 board alone: 20mA
Input Module max current: 23mA
Output Module max current: 16mA
External Power Connector: Two-position terminal block

Overload Protection: 5A fuse on all input/outputs.

INPUTS/OUTPUTS 20 total points; user-selectable channel-by-channel as

inputs or outputs
Inputs:
Input Type: Input ratings depend on input
module(s) selected.

Outputs:
Output Type: Output ratings depend on input
module(s) selected.

I/O Connections: 25-position DB25 Female to DM-20

40-position screw-type terminal block for I/O
Compatible* Modules:
Opto-22 Inputs IDC24; 10-30VDC
IAC24; 90-140VAC or VDC
IAC24A; 180-240VAC

Opto-22 Outputs ODC5; 60VDC@3A

ODC5A; 200VDC@1A
OAC5; 120VAC@3A
OAC5A; 240VAC@3A
OAC5A5; 120/240VAC@3A

* These manufacturers and model numbers represent devices that should be compatible. Their physical
and electrical specifications appear to meet those of our product. However, this list does not constitute
an endorsement of the product nor does it imply that the specifications listed are accurate. Ratings listed
are nominal. Refer to manufacturer’s data sheets for limitations.

124 Schneider Electric

 DIO-20

DIO-20 Installation

The DIO-20 (which includes the DIO 20 printed circuit board, three plastic PCB mounting
brackets, and three plastic DIN rail mounting brackets) can be mounted to either a DIN
Rail or directly to a bulkhead. The following are additional items required for installing the
DIO-20:

• Andover Continuum DM-20 I/O module

• 24 VDC Power Source
• Input/Output Wires
• 25-pin Interface cable
• Input/Output Modules
• Two DIN End Clamps
• DIN Rail
• Enclosure

Mounting to a DIN Rail

1. Slide an end clamp into position on the DIN Rail. Tighten the holding screws.

End Clamp

DIN Rail
PCB
Mounting
Bracket

DIN Rail
Mounting
Bracket

2. Slide a DIN Rail Mounting Bracket under the PCB mounting bracket until flush on
the back side.

Andover Continuum I/O System Reference 125

DIO-20
3. Slide the DIN rail mounting bracket/PCB bracket assembly onto the DIN rail until
flush with the end clamp.
4. Insert one end of the module PCB into the PCB bracket. Slide the board into the
middle channel of the mounting bracket. Slide the DIN rail/PCB mounting bracket
assembly onto the board and DIN rail. Carefully slide the assembled brackets
into the center of the module board.
5. Slide the remaining bracket onto the DIN rail and position it at the end of the
board.
6. Mount another end clamp. Tighten the screws on the end clamp.

Mounting Directly to a Panel

There are four #6-sized holes (0.156” (4mm)) provided at the corners and one in the
center for mounting using stand-offs directly to a flat surface. The following illustrates the
mounting dimensions of the module.

8.05 “ (204) Output

15.7 “ (399)

2.05”(52)
4.3”
3.88 “ (98) (108)

16.1 “ (409)

126 Schneider Electric

 DIO-20
I/O Connections
The connections to the DM-20 are located on a 25-position DB25-type female connector
located at the left side of the module. A separate two-conductor screw-type terminal
connector provides 24VDC power.
The input/output connections are located on a 40-position terminal block connector along
the bottom of the module. These connections are labeled I/O1, I/O2, I/O3, and so forth.
Each input/output occupies two adjacent positions of the connector.
The diagram below indicates where each input number is located on the module.
24VDC * Main Power
Connection Fuse LED Status
LEDs

25-pin D Cable
from DO80-LED
or DM-20 Module

Output Input/Output 1 Input/Output

Connection Screw Terminals
Fuses typical

25-Pin D Connector

Connection Description Connection Description

1 I/O 1 13 I/O 13
2 I/O 2 14 I/O 14
3 I/O 3 15 I/O 15
4 I/O 4 16 I/O 16
5 I/O 5 17 I/O 17
6 I/O 6 18 I/O 18
7 I/O 7 19 I/O 19
8 I/O 8 20 I/O 20
9 I/O 9 21 Ground
10 I/O 10 22 Ground
11 I/O 11 23 Ground
12 I/O 12 24 Ground
25 Ground

Andover Continuum I/O System Reference 127

DIO-20

40-Position Terminal Block

Connection Description Connection Description

1 I/O 1 21 I/O 11
2 I/O 1 22 I/O 11
3 I/O 2 23 I/O 12
4 I/O 2 24 I/O 12
5 I/O 3 25 I/O 13
6 I/O 3 26 I/O 13
7 I/O 4 27 I/O 14
8 I/O 4 28 I/O 14
9 I/O 5 29 I/O 15
10 I/O 5 30 I/O 15
11 I/O 6 31 I/O 16
12 I/O 6 32 I/O 16
13 I/O 7 33 I/O 17
14 I/O 7 34 I/O 17
15 I/O 8 35 I/O 18
16 I/O 8 36 I/O 18
17 I/O 9 37 I/O 19
18 I/O 9 38 I/O 19
19 I/O 10 39 I/O 20
20 I/O 10 40 I/O 20

128 Schneider Electric

 AC-1
AC-1
Access Control Module
The AC-1, Access Control Module, provides full I/O for an access controlled door or
portal in one compact module. The AC-1 can be remotely located at a door reader for
localized control and reduced wiring costs; or several AC-1 modules can be grouped
together and DIN rail-mounted for centralized control.

The AC-1 provides a Wiegand card input for Wiegand and Proximity type cards, reading
up to 64 bits per card. Reader power is switch-selectable between 5 volts and 12 Volts to
meet most card reader power requirements.

The AC-1 provides two 5 Amp, Form C relays⎯one for the door lock and a second for
local alarm annunciation. Each output has an integral hand-off-auto switch for manual
operation, and software feedback of the switch position.

Up to three supervised alarm inputs can be used for door status contacts, request-to-exit
devices, a cabinet tamper switch, and any other two-state or three-state (on/off/trouble)
alarm device.

Keypad Control
The AC-1 supports Wiegand output keypads. To simplify installation and reduce wiring
costs, the keypad data comes into the module via the reader data lines.

FEATURES
• 1 Card Reader Input
• +5 V or +12 V reader power (switch
selectable)
• 1 Card Reader LED control output
• Up to 3 Supervised Inputs
• 2 FormC Relay Outputs rated
24 VAC/DC @ 5A
• Override Toggle Switches
w/Override Detection and Feedback

Andover Continuum I/O System Reference 129

AC-1

SPECIFICATIONS
ELECTRICAL
Power Supply Range: Input Voltage Range: 20-26V. 24V UL294 installations.
Power Consumption: 2.6 Watts + (15 Volts) * (Reader Current) max. @ 24 VDC;
normally provided by Andover Continuum power supply module.
Overload Protection: 0.5 A resettable fuse with transient voltage suppressor
(TVS) and reverse polarity protection

INPUTS/OUTPUTS

Inputs
Card Readers: 1
Card Reader Type: Wiegand and Proximity readers *
Maximum Number
of bits/Card: 64
Card Reader Power: +5 V or +12 V (switch selectable)
Switch Setting Output Voltage Output Current
+5 V +5.20 V ±0.05V 120 mA (max.)
+12 V +12.0 V ±5% 180 mA (max.)
Wiring Distance:
Card Reader to AC-1: 500 ft. max. using 18-gauge wire
200 ft. max. using 22-gauge wire

Alarm Inputs: Up to 3 supervised inputs. Single or double resistor

supervision, series or parallel.

Input Protection: Transient Voltage Suppressor (TVS) on each input

Outputs
Door Outputs: 2 Form C relays
Output Rating: 24 VAC/VDC @ 5 Amp
Reader LED Output: Open collector; up to 50 mA.
Output Protection: 5000 V isolation 270 V MOVs on each output
Overrides: 3-position manual override switch on each output for
manual control of relay. LED override status indicator.
Override Feedback: Override detection and software feedback provided for
each output.

* The following reader and keypad models are the only approved for use in UL 294 Access Control
applications:
Essex KTP-163-SN keypad; HID Epic 32985 reader; Indala ASR-500 reader.

130 Schneider Electric

 AC-1

I/O Connections
The actual I/O connections are located on a sixteen-position removable screw terminal
connector located at the bottom of the module. Wires should enter from either the top or
bottom wiring troughs, and outputs should come from the right side of the rack, inputs
from the left (by convention).

The diagram below indicates where each output number is located in the terminal block.

Connection Description

Earth Ground
1. Reader +V
2. Reader GND
3. Reader DATA (Wiegand I)
4. Reader CLK (Wiegand 0)
5. Reader LED
6. Sup Input Aux
7. Sup Input Door
8. Sup Input REX
9. Sup Input RETURN
10. Door NC
11. Door NO
12. Door COM
13. OUT2 NC
14. OUT2 NO
15. OUT2 COM

Andover Continuum I/O System Reference 131

AC-1

Using the AC-1

AC-1 is a complete card access control module designed to interface with the Schneider
Electric NetController where an internal firmware-based Access Control supervisor
resides. During normal operation, access control decisions are made in the Andover
Continuum NetController CPU module database, which provides storage for up to 75,000
“local” personnel records (up to 4 million records may be created per database).
The AC-1 is designed to control a single door. The door can be configured to allow
entrance based on card only, card plus personal ID number (PIN), or keypad only. The
door’s operating mode can even be changed based on time-of-day or other events for
optimum flexibility through Schneider Electric’s easy-to-use Plain English programming
language. Each keypad can also permit entry of a duress alarm code that can initiate an
alarm sequence at any AC-1 controller or at the CyberStation workstation.
Time-based anti-passback and entry/egress anti-passback are available to prevent
tailgating. Entry/egress anti-passback is system-wide and can be performed by readers
located on different AC-1 controllers across the network.
Using Plain English, the AC-1 can also be used for custom access control sequences
such as two-man rule, optical turnstile control, and man trap configurations.

Reader Power Switch

Readers are available in both 5 Volt and 12 Volt varieties. The AC-1 module supports
both by allowing the selection of a reader power source. A voltage selector switch is
located on the front panel of the module. Insert the tip of a small screwdriver to slide the
internal power switch into the desired position.

Caution: Make sure the Reader Power switch is set properly. Setting the switch to
12 V for a 5 V reader may damage the unit.
READER
POWER

+ 5V, 120mA

+ 12V, 180mA

Internal switch slides up and

down to make selection

132 Schneider Electric

 AC-1

Degrade Mode
If network communications are interrupted, as a fail-safe mode, the AC-1 will revert to a
programmable degraded mode of operation. System operation during degrade mode
provides uninterrupted card access using site codes, cards formats, and other degrade
mode parameters stored in non-volatile EEPROM in each AC-1 module.

Degrade mode parameters are configured from the “Access Validation” section of the
door editor’s “Entry Reader” tab. For dual reader doors, configurable degrade mode
parameters are available from the “Access Validation” section of the door editor’s “Exit
Reader” tab.

During degrade mode, the AC-1 module supports:

ƒ Two of the site codes entered on the “Card Formats” tab of the door editor (out
of four supported by the door during normal operation). The site codes
supported are Site1 and Site2.
ƒ One card type (determined below)

In NetController version 1.4 and forward, when more than one card type is selected at the
door, the following procedure determines which one of the card types the AC-1 stores for
degrade mode operation:
1. Open the door editor and de-select all card types except the one that you want
the AC-1 to store for degrade mode operation.
2. Save the door settings by clicking “Apply”.
3. Select the other card types that will be allowed at the door in normal operation.
4. Save the door settings again by clicking “Apply” or “OK” to save and close the
door editor.

WARNING: The AC-1 is not recommended for use with inverted door output
installations. For inverted door output installations, use the AC-1A or AC-
1 Plus modules.

Andover Continuum I/O System Reference 133

AC-1

Connecting a Reader/Keypad
Reader/Keypad Inputs
The AC-1 includes a full interface to a single Wiegand access card reader. The modules
were designed to allow integral reader/keypad units to be connected directly. Separate
keypads that have similar interfaces (Wiegand) can be connected in parallel with a reader
through the use of the Keypad Interface Module as shown on the following page.

The Wiegand reader and/or reader/keypad unit is connected to the AC-1 module as
shown below:

+V 5V

12 V

GND

+V

GND
Wiegand DATA / I
DATA I
Reader
or DATA 0
Reader with Keypad LED

CLK / 0

LED

134 Schneider Electric

 AC-1

Connecting Two Readers or a Keypad and a Reader

With the addition of the Keypad Interface Module (KIM), the AC-1 can interface to both a
keypad and a reader simultaneously. This assumes that they are both Wiegand devices
of similar voltage range. The KIM module presents the AC-1 with one pair of signals.
Similarly, two readers can be connected with the KIM. This allows a site to slowly
introduce a different type of reader (i.e., proximity) while allowing access through the
normal reader. The KIM connects as shown below:

Note: The KIM is not approved for use with UL 294 Access Control Systems.

AC-1

+V

GND

+V

GND
Wiegand Reader
LED
or
Reader with Keypad DATA 1
or Keypad only CLK 0
LED

Keypad Interface Module

P3

DATA / I

CLK / 0 P1
DATA / I DATA / I
P2
CLK / 0 CLK / 0
DATA / I
CLK / 0

DATA 1
CLK 0
Wiegand Reader LED
or
GND
Reader with Keypad
or Keypad only +V

Andover Continuum I/O System Reference 135

AC-1

Connecting a CardKey Reader via the EMX34

With the addition of the Schneider Electric EMX34 CardKey to Wiegand interface you can
connect a CardKey reader to the AC-1.

The reader connects as shown below:

136 Schneider Electric

 AC-1

Connecting a Dual Reader Door

With the addition of another AC-1 module, a door can be configured as a dual reader
door. A door is a dual reader door when it has been configured with an entry and exit IOU
module.

A dual reader door is connected as shown below:

AC-1 Entry IOU

Supervised Input
REX

Door
Supervised Input
Door
Switch

Entry Reader Alarm

Reader Out2
Out
1-Door

Door
AC-1 Exit IOU Strike

Supervised
Input Resistor
Configuration
(Corresponds to
type of supervised
input on AC-1
Exit Reader Reader Entry IOU)

1-Door

NOTE: As the door switch connects only to the Entry IOU, the door switch operation at
the Exit IOU is not supported in degrade mode.

NOTE: The resistor configuration on the AC-1 Exit IOU matches the resistor configuration
of the supervised input type. (Examples: NC Series, NC Series Parallel, or NO Series
Parallel.) Connect only the resistor across the input, not any other wire connections.

Andover Continuum I/O System Reference 137

AC-1

Connecting Supervisory Inputs

All AC-1 inputs are supervisory inputs. The following drawings depict the three types of
supervisory inputs that exist—two normally closed and one normally open type.

NOTE: All resistor values are to be 10K ± 5%.

Normally Closed Supervised Inputs

NC Series
With this type of input wiring, a resistor is placed in series with the input being monitored.
When the input contact presents a short circuit (normal closed position) the input is
assumed in a normal closed state, the circuit presents a reading of 10 K Ωs at the input.

Circuit Action Input Senses Condition

Switch Closed External Resistance Input contact Closed
Switch Opened Infinite Resistance Input contact Open
Wire Cut Infinite Resistance Input contact Open ‘Violation’
Input Shorted Zero Ωs Violation or error

When the input contact is opened, the circuit opens and an infinite resistance is
measured. If the wires to the input contact are cut it also appears as an “Input Contact
Open” condition. In this case there would be an input contact open without a valid card
swipe or valid keypad entry resulting in an “Input Contact Violation”. Shorting the input
causes a zero Ω resistance, which also results in an input contact violation.

When configuring for this type of contact select:

ElecType: Supervised
Resistor Type: NCSeries

138 Schneider Electric

 AC-1

Normally Closed Supervised Inputs

NC Series Parallel
With this type of input wiring, two external resistors are added to the input, one in series
and the other in parallel. When the input contact switch is closed (normal position) the
input contact is assumed to be closed. The circuit presents a reading composed of both
resistances in parallel that works out to be half the value of one of them (5 KΩ).

Circuit Action Input Senses Condition

Switch Closed External Resistance ÷ 2 Input contact Closed
Switch Opened External Resistance Input contact Open
Wire Cut Infinite Resistance Violation or error
Input Shorted Zero Ωs Violation or error

When the input contact is opened the switch opens and the value of the parallel resistor
is measured. If the wires to the input contact are cut it appears as an infinite resistance.
Shorting the input causes a zero Ω resistance. Both a short and an infinite resistance
(open) should result in an error condition.

When configuring for this type of contact select:

ElecType: Supervised
Resistor Type: NCSerPar

Andover Continuum I/O System Reference 139

AC-1

Normally Open Supervised Inputs

NO Series Parallel
With this type of input wiring, two external resistors are added to the input, one in series
and the other in parallel. When the input contact switch is open (normal position), the
input contact is assumed to be closed. The circuit reads the value of the parallel resistor.

Circuit Action Input Senses Condition

Switch Closed External Resistance ÷ 2 Input contact Open
Switch Opened External Resistance Input contact Closed
Wire Cut Infinite Resistance Violation or error
Input Shorted Zero Ωs Violation or error

When the input contact is opened, the switch closes and a reading results that is
composed of both resistances in parallel that works out to be half the value of one of
them (5 KΩ). If the wires to the input contact are cut it appears as an infinite resistance.
Shorting the input causes a zero Ω resistance. Both a short and an infinite resistance
(open) should result in an error condition.

When configuring for this type of contact select:

ElecType: Supervised
Resistor Type: NOSeriPar

140 Schneider Electric

 AC-1

Wiring Door Switches

There are three supervisory inputs for door switches. The maximum length wire you can
use is 500 ft of #18 gauge wire (152 m of 1.0 mm2 wire) or 200 ft of #22 gauge wire (60
m of 0.35 mm2 wire).

Some switches have built-in resistors that facilitate Series Parallel connections as shown
below:
Switch with AUX
Built-In Resistor or
DOOR
or
REX

10 KΩ

RET

Wiring Motion Detectors

Motion detectors are devices that close a switch contact when motion is detected.

Wiring is similar to a normal door switch input; however, the motion sensor requires an
external power supply of 12 VDC or 24 VDC (UL listed under APHV). The maximum
length wire you may use is 500 ft of #18 gauge wire (152 m of 1.0 mm2 wire) or 200 ft of
#22 gauge wire (60 m of 0.35 mm2 wire).
The following shows a typical motion detector circuit:

No AUX
Motion or
Detected DOOR
or
REX
Normally Open 10 KΩ
PIR Motion
Detector

RET

Motion AUX
Detected or
DOOR
or
REX
Normally Open 10 KΩ
PIR Motion
Detector

RET

Andover Continuum I/O System Reference 141

AC-1

Connecting Outputs

The AC-1 module includes two Form C single-pole double-throw relay outputs. The
following is a simplified schematic of each output channel:

OUT x NC

OUT x NO

OUT x COM

Both channels resemble the circuit shown above.

To use the Form C output in your system, configure an output point with an Electrical
Type of Digital.
These output contacts operate as a standard relay. When the output is set to an “ON”
state, the normally open contacts close and the normally closed contacts open.

Note: When configuring a Digital point, there is a “Polarity” attribute. If this attribute is
enabled, the operation of the outputs are reversed.

Override Controls
The AC-1 module includes an output override switch for each output.

ON

OFF

AUTO

The output of the module can be directed from program control or manual control. The
output can be disabled completely as well.

142 Schneider Electric

 AC-1

The following describes the actions associated with each position of the override controls:

ON The output relay is energized to an “ON”’ state manually by

setting the switch to ON. Programs have no effect on the output
when the switch is in this position.

OFF The output relay is de-energized to an “OFF” state manually by

setting the switch to OFF. Programs have no effect on the output
when the switch is in this position.

AUTO The action of the output relay is determined as a direct result of

program control.

Andover Continuum I/O System Reference 143

AC-1

Wiring Door Outputs

The following represents a typical door output installation when the circuit is normally
open:

This configuration shows a normally de-energized lock (when secured) in a fail secure
mode. If power loss occurs, the lock closes. Always be sure to use “panic” hardware that
allows emergency exit from the secured area.

144 Schneider Electric

 AC-1

Wiring Dual Reader Door Outputs

The following represents a typical door output installation when the dual reader door
circuit is controlling a fail-secure lock:

Andover Continuum I/O System Reference 145

AC-1

Status/Control Panel
Status Indicators
The AC-1 module includes a complete indicator status panel on the front of the module.

This panel includes indicators reporting on the status of the following:

POWER This green indicator illuminates when DC power is applied through the
I/O Bus.
COMM This yellow indicator illuminates when data is transmitted from the
module to the NetController. In normal operation, data is only transmitted
when an input value changes.

This indicator will also flash periodically as the NetController checks the
I/O bus.
OVERRIDE This red indicator illuminates whenever any of the override switches is in
a position other than AUTO.
STATUS This red indicator is normally off. If it is always on or flashing at a fast
rate, there is a problem with the module.

This indicator can be manually illuminated from the CyberStation

workstation or Command Terminal and used as a troubleshooting aid
when locating a particular module.
OUTPUT These red indicators (one for each channel) illuminate when an output
relay is energized.
READER POWER

+5V, +12V These green indicators illuminate when either voltage is selected as the
reader power source.

146 Schneider Electric

 AC-1

This panel also includes two operator switches that perform the following:

COMMISSION After physical installation and during configuration through the

CyberStation workstation or Command Terminal, pressing this button
registers the module’s address with the system. For more information,
refer to the section on Module Configuration found earlier in this manual.
RESET Should the module become inoperable, pressing this button resets the
module. It does not erase its memory.

Andover Continuum I/O System Reference 147

AC-1A

AC-1A
Access Control Module
The AC-1A, Access Control Module, provides full I/O for an access controlled door or
portal in one compact module. The AC-1A can be remotely located at a door reader for
localized control and reduced wiring costs; or several AC-1A modules can be grouped
together and DIN rail-mounted for centralized control.

The AC-1A provides a Wiegand card input for Wiegand and Proximity type cards, reading
up to 64 bits per card. Reader power (5 volts) is provided to meet most card reader
power requirements.

The AC-1A includes two 5 Amp, Form C relays⎯one for the door lock and a second for
local alarm annunciation. Each output has an integral hand-off-auto switch for manual
operation, and software feedback of the switch position.

Up to three supervised alarm inputs can be used for door status contacts, request-to-exit
devices, a cabinet tamper switch, and any other two-state or three-state (on/off/trouble)
alarm device.

Keypad Control
The AC-1A supports Wiegand output keypads. To simplify installation and reduce wiring
costs, the AC-1A has a second set of connections.

FEATURES
• 1 Card Reader Input*
• 1 Keypad Input*
* Only one of these two devices can be active
at any given moment.

• +5 V reader power
• 1 Card Reader LED control output
• Up to 3 Supervised Inputs
• 2 FormC Relay Outputs rated
24 VAC/DC @ 5A
• Override Toggle Switches
w/Override Detection and Feedback
• 10–28 V Power Supply Range

148 Schneider Electric

 AC-1A

SPECIFICATIONS
ELECTRICAL
Power Supply Range: Input Voltage Range: 10-28V. 24V for UL864 and UL294
installations.
Power Consumption: 2.0 Watts + (Input Voltage) * (Reader Current) max. @ 24 VDC;
normally provided by Andover Continuum power supply module.
Overload Protection: 0.5 A resettable fuse with transient voltage suppressor
(TVS) and reverse polarity protection

INPUTS/OUTPUTS

Inputs
Card Readers: 1*
Keypads: 1*
Card Reader Type: Wiegand and Proximity readers
Maximum Number
of bits/Card: 64

Card Reader Power: +5 V (±3%) @50 mA (max.)

Wiring Distance:
To Card Reader: 500 ft. max. using 18-gauge wire
200 ft. max. using 22-gauge wire
Alarm Inputs: Up to 3 supervised inputs. Single or double resistor
supervision, series or parallel.

Input Protection: Transient Voltage Suppressor (TVS) on each input

* Only one of these two devices can be active at any given moment.

Outputs
Door Outputs: 2 Form C relays
Output Rating: 24 VAC/VDC @ 5 Amp
Reader LED Output: Open collector; up to 100 mA.
Output Protection: 5000 V isolation 270 V MOVs on each output
Overrides: 3-position manual override switch on each output for
manual control of relay. LED override status indicator.

Override Feedback: Override detection and software feedback provided for

each output.

Andover Continuum I/O System Reference 149

AC-1A

I/O Connections
The actual I/O connections are located on an eighteen-position removable screw terminal
connector located at the bottom of the module. Wires should enter from either the top or
bottom wiring troughs, and outputs should come from the right side of the rack, inputs
from the left (by convention).

The diagram below indicates where each output number is located in the terminal block.

Connection Description

Earth Ground
1. Reader +5V
2. Reader GND
3. Reader DATA (Wiegand I)
4. Reader CLK (Wiegand 0)
5. Keypad DATA (Wiegand I)
6. Keypad CLK (Wiegand 0)
7. Reader LED
8. Sup Input 1 Aux
9. Sup Input 2 Door
10. Sup Input 3 REX
11. Sup Input RETURN
12. 1-Door NC
13. 1-Door NO
14. 1-Door COM
15. OUT2 NC
16. OUT2 NO
17. OUT2 COM

150 Schneider Electric

 AC-1A

Using the AC-1A

AC-1A is a complete card access control module designed to interface with the
Schneider Electric NetController where an internal firmware-based Access Control
supervisor resides. During normal operation, access control decisions are made in the
Andover Continuum NetController CPU module database, which provides storage for up
to 75,000 “local” personnel records (up to 4 million records may be created per
database).
The AC-1A is designed to control a single door. The door can be configured to allow
entrance based on card only, card plus personal ID number (PIN), or keypad only. The
door’s operating mode can even be changed based on time-of-day or other events for
optimum flexibility through Schneider Electric’s easy-to-use Plain English programming
language. Each keypad can also permit entry of a duress alarm code that can initiate an
alarm sequence at any AC-1A controller or at the CyberStation workstation.
Time-based anti-passback and entry/egress anti-passback are available to prevent
tailgating. Entry/egress anti-passback is system-wide and can be performed by readers
located on different AC-1A controllers across the network.
Using Plain English, the AC-1A can also be used for custom access control sequences
such as two-man rule, optical turnstile control, and man trap configurations.

The AC-1A also supports inverted door output installations.

Degrade Mode
If network communications are interrupted, as a fail-safe mode, the AC-1A will revert to a
programmable degraded mode of operation. System operation during degrade mode
provides uninterrupted card access using site codes, cards formats, and other degrade
mode parameters stored in non-volatile EEPROM in each AC-1A module.

Degrade mode parameters are configured from the “Access Validation” section of the
door editor’s “Entry Reader” tab. For dual reader doors, configurable degrade mode
parameters are available from the “Access Validation” section of the door editor’s “Exit
Reader” tab.

Andover Continuum I/O System Reference 151

AC-1A

During degrade mode, the AC-1A module supports:

ƒ Two of the site codes entered on the “Card Formats” tab of the door editor (out
of four supported by the door during normal operation). The site codes
supported are Site1 and Site2.
ƒ One card type (determined below)

Note: In the NetController version 1.4 and forward, when more than one card type is
selected at the door, the following procedure determines which one of the card types the
AC-1A stores for degrade mode operation:
1. Open the door editor and de-select all card types except the one that you want
the AC-1A to store for degrade mode operation.
2. Save the door settings by clicking “Apply”.
3. Select the other card types that will be allowed at the door in normal operation.
4. Save the door settings again by clicking “Apply” or “OK” to save and close the
door editor.

152 Schneider Electric

 AC-1A

Connecting a Reader/Keypad
Reader/Keypad Inputs
The AC-1A includes a full interface to a single Wiegand access card reader and a
keypad. The modules were designed to allow Integral reader/keypad units to be
connected directly. Separate keypads that have similar interfaces (Wiegand) can be
connected through the keypad connections provided on the terminal block.

The Wiegand reader, keypad and/or reader/keypad unit is connected to the AC-1A
module as shown below:

+ 5V

GND

+V

Wiegand Reader GND

DATA / I
or DATA I
Wiegand Keypad DATA 0
or
LED
Reader with Keypad
CLK / 0

LED

Andover Continuum I/O System Reference 153

AC-1A

Connecting Two Readers or a Keypad and a Reader

The AC-1A can interface to both a keypad and a reader simultaneously. This assumes
that they are both Wiegand devices of similar voltage range.

Similarly, two readers can be connected. This allows a site to slowly introduce a different
type of reader (i.e., proximity) while allowing access through the normal reader. The
connections are as shown below:
AC-1A

+ 5V
1

GND
2
+V

GND
Wiegand Reader LED
or
DATA 1
Wiegand Keypad
CLK 0
LED
7

DATA / I
3
CLK / 0
4

DATA / I
5
CLK / 0
6

DATA 1
CLK 0
Wiegand Reader LED
or
Wiegand Keypad GND
+V

154 Schneider Electric

 AC-1A

Connecting Two Readers for a Dual Reader Door

With the addition of another AC-1A module, a door can be configured as a dual reader
door. A door is a dual reader door when it has been configured with an entry and exit
IOU module.

A dual reader door is connected as shown below:

Request to
AC-1A Entry IOU Exit Device
Supervised Input
REX

Door
Supervised
Input Door
Switch

Entry Reader Alarm

Reader Out2
Out
1-Door

Door
AC-1A Exit IOU Strike

Exit Reader Reader

1-Door

Note:
As the door switch connects only to the Entry IOU, the door switch operation at the
Exit IOU is not supported in degrade mode.

Andover Continuum I/O System Reference 155

AC-1A

Connecting Supervisory Inputs

All AC-1A inputs are supervisory inputs. The following drawings depict the three types of
supervisory inputs that exist—two normally closed and one normally open type.

NOTE: All resistor values are to be 10K ± 5%.

Normally Closed Supervised Inputs

NC Series
With this type of input wiring, a resistor is placed in series with the input being monitored.
When the input contact presents a short circuit (normal closed position), the input is
assumed to be in a normal closed state, the circuit presents a reading of 10 K Ωs at the
input.

Circuit Action Input Senses Condition

Switch Closed External Resistance Input contact Closed
Switch Opened Infinite Resistance Input contact Open
Wire Cut Infinite Resistance Input contact Open ‘Violation’
Input Shorted Zero Ωs Violation or error

When the input contact is opened, the circuit opens and an infinite resistance is
measured. If the wires to the input contact are cut it also appears as an “input contact
open” condition. In this case there would be an input contact open without a valid card
swipe or valid keypad entry resulting in an “input contact violation”. Shorting the input
causes a zero Ω resistance, which also results in an input contact violation.

When configuring for this type of contact select:

ElecType: Supervised
Resistor Type: NCSeries

156 Schneider Electric

 AC-1A

Normally Closed Supervised Inputs

NC Series Parallel
With this type of input wiring, two external resistors are added to the input, one in series
and the other in parallel. When the input contact switch is closed (normal position), the
input contact is assumed to be closed. The circuit presents a reading composed of both
resistances in parallel that works out to be half the value of one of them (5 KΩ).

Circuit Action Input Senses Condition

Switch Closed External Resistance ÷ 2 Input contact Closed
Switch Opened External Resistance Input contact Open
Wire Cut Infinite Resistance Violation or error
Input Shorted Zero Ωs Violation or error

When the input contact is opened, the switch opens and the value of the parallel resistor
is measured. If the wires to the input contact are cut it appears as an infinite resistance.
Shorting the input causes a zero Ω resistance. Both a short and an infinite resistance
(open) should result in an error condition.

When configuring for this type of contact select:

ElecType: Supervised
Resistor Type: NCSerPar

Andover Continuum I/O System Reference 157

AC-1A

Normally Open Supervised Inputs

NO Series Parallel
With this type of input wiring, two external resistors are added to the input, one in series
and the other in parallel. When the input contact switch is open (normal position) the
input contact is assumed to be closed. The circuit reads the value of the parallel resistor.

Circuit Action Input Senses Condition

Switch Closed External Resistance ÷ 2 Input contact Open
Switch Opened External Resistance Input contact Closed
Wire Cut Infinite Resistance Violation or error
Input Shorted Zero Ωs Violation or error

When the input contact is opened the switch closes and a reading results that is
composed of both resistances in parallel that works out to be half the value of one of
them (5 KΩ). If the wires to the input contact are cut it appears as an infinite resistance.
Shorting the input causes a zero Ω resistance. Both a short and an infinite resistance
(open) should result in an error condition.

When configuring for this type of contact select:

ElecType: Supervised
Resistor Type: NOSeriPar

158 Schneider Electric

 AC-1A

Wiring Door Switches

There are three supervisory inputs for door switches. The maximum length wire you can
use is 500 ft of #18 gauge wire (152 m of 1.0 mm2 wire) or 200 ft of #22 gauge wire (60
m of 0.35 mm2 wire).

Some switches have built-in resistors that facilitate Series Parallel connections as shown
below:

Switch with AUX

Built-In Resistor or
DOOR
or
REX

10 KΩ

RET

Wiring Motion Detectors

Motion detectors are devices that close a switch contact when motion is detected.

Wiring is similar to a normal door switch input, however, the motion sensor requires an
external power supply of 12 VDC or 24 VDC (UL listed under APHV). The maximum
length wire you may use is 500 ft of #18 gauge wire (152 m of 1.0 mm2 wire) or 200 ft of
#22 gauge wire (60 m of 0.35 mm2 wire).

The following shown a typical motion detector circuit:

No AUX
Motion or
Detected DOOR
or
REX
Normally Open 10 KΩ
PIR Motion
Detector

RET

Motion AUX
Detected or
DOOR
or
REX
Normally Open 10 KΩ
PIR Motion
Detector

RET

Andover Continuum I/O System Reference 159

AC-1A
Connecting Outputs
The AC-1A module includes two Form C single-pole double-throw relay outputs. The
following is a simplified schematic of each output channel:

OUT x NC

OUT x NO

OUT x COM

Both channels resemble the circuit shown above.

To use the Form C output in your system, configure an output point with an Electrical
Type of Digital.
These output contacts operate as a standard relay. When the output is set to an “ON”
state, the normally open contacts close and the normally closed contacts open.

NOTE: When configuring a Digital point, there is a ‘Polarity’ attribute. If this attribute is
enabled, the operation of the outputs are reversed.

Override Controls
The AC-1A module includes an output override switch for each output.

ON

OFF

AUTO

The output of the module can be directed from program control or manual control. The
output can be disabled completely as well.

160 Schneider Electric

 AC-1A

The following describes the actions associated with each position of the override controls:

ON The output relay is energized to an “ON” state manually by

setting the switch to ON. Programs have no effect on the output
when the switch is in this position.

OFF The output relay is de-energized to an “OFF” state manually by

setting the switch to OFF. Programs have no effect on the output
when the switch is in this position.

AUTO The action of the output relay is determined as a direct result of

program control.

Wiring Door Outputs

The following represents a typical door output installation when the circuit is normally
open:

MOV
(Andover #01-2020-095)

C
Door Strike
(UL listed burglary-resistant
electric locking mechanism (CVXY))

12/24V

Power Supply
(UL listed power supply (APHV))

This configuration shows a normally de-energized lock (when secured) in a fail secure
mode. If power loss occurs, the lock closes. Always be sure to use “panic” hardware that
allows emergency exit from the secured area.

Andover Continuum I/O System Reference 161

AC-1A

The following represents a typical door output installation when the circuit is normally
closed:
MOV
(Andover #01-2020-095)

Electromagnetic Door Lock

(UL listed burglary-resistant
electric locking mechanism (CVXY))

12/24V

Power Supply
(UL listed power supply (APHV))

This configuration shows a normally de-energized lock (when secured), in a fail safe
mode. If power loss occurs, the lock opens.

162 Schneider Electric

 AC-1A

Wiring Dual Reader Door Outputs

The following represents a typical door output installation when the dual reader door
circuit is controlling a fail-secure lock:

Exit IOU

Entry IOU

MOV
(Andover #01-2020-095)

C
Door Strike
Fail-Secure
(UL listedDoor Lock
burglary-resistant
(Energize
electric to unlock)
locking mechanism (CVXY))
UL-listed burglary-resistant
Electric locking mechanism (CVXY)

12/24V

Power Supply
(UL listed power supply (APHV))

Andover Continuum I/O System Reference 163

AC-1A

The following represents a typical door output installation when the dual reader door
circuit is controlling a fail-safe lock:

Exit IOU

MOV
(Andover #01-2020-095)
Entry IOU

Electromagnetic
Fail-Safe Door LockDoor Lock
(UL listed
(Energize toburglary-resistant
lock)
electric locking mechanism (CVXY))
UL-listed burglary-resistant
Electric locking mechanism (CVXY)

12/24V

Power Supply
(UL listed power supply (APHV))

164 Schneider Electric

 AC-1A

Status/Control Panel
Status Indicators
The AC-1A module includes a complete indicator status panel on the front of the module.

This panel includes indicators reporting on the status of the following:

POWER This green indicator illuminates when DC power is applied through the
I/O Bus.
COMM This yellow indicator illuminates when data is transmitted from the
module to the NetController. In normal operation, data is only transmitted
when an input value changes.

This indicator will also flash periodically as the NetController checks the
I/O bus.
OVERRIDE This red indicator illuminates whenever any of the override switches is in
a position other than AUTO.
STATUS This red indicator is normally off. If it is always on or flashing at a fast
rate, there is a problem with the module.

This indicator can be manually illuminated from the CyberStation

workstation or Command Terminal and used as a troubleshooting aid
when locating a particular module.
OUTPUT These red indicators (one for each channel) illuminate when an output
relay is energized.
READER POWER

+5V This green indicator illuminates when the reader power source is
operational.
Andover Continuum I/O System Reference 165
AC-1A

This panel also includes two operator switches that perform the following:

COMMISSION After physical installation and during configuration through the

CyberStation workstation or Command Terminal, pressing this button
registers the module’s address with the system. For more information,
refer to the section on Module Configuration found earlier in this manual.
RESET If the module becomes inoperable, pressing this button resets the
module. It does not erase its memory.

166 Schneider Electric

 AC-1 Plus

AC-1 Plus
Access Control Module
The AC-1 Plus, Access Control Module, provides full I/O for an access controlled door or
portal in one compact module. The AC-1 Plus can be remotely located at a door reader
for localized control and reduced wiring costs; or several AC-1 Plus modules can be
grouped together and DIN rail-mounted for centralized control.
The AC-1 Plus provides a reader input connection for Wiegand/ABA/CK34 and Proximity
type cards, reading up to 64 bits per card for Wiegand cards and 255 bits per card for
ABA cards. Reader power (5 volts) is provided to meet most card reader power
requirements.
The AC-1 Plus includes two 5 Amp, Form C relays⎯one for the door lock and a second
for local alarm annunciation. Each output has an integral hand-off-auto switch for manual
operation, and software feedback of the switch position.
Up to five supervised alarm inputs can be used for door status contacts, ADA request-to-
exit devices, a cabinet tamper switch, and any other two-state or three-state
(on/off/trouble) alarm device.

Keypad Control
The AC-1Plus supports Wiegand output keypads. To simplify installation and reduce
wiring costs, the keypad data comes into the module via the reader data lines.

FEATURES
• 1 Card Reader Input*
• 1 Keypad Input*
♦ *Only one of these two devices can be
active at any given moment.
• Wiegand/ABA or CK34 formats
supported
• +5 V reader power
• 2 Card Reader LED control outputs
• Up to 5 Supervised Inputs
• 2 FormC Relay Outputs rated
24 VAC/DC @ 5A
• Override Toggle Switches
w/Override Detection and Feedback
• Supports Bond Sensor and ADA
input switches

Andover Continuum I/O System Reference 167

AC-1 Plus
SPECIFICATIONS
ELECTRICAL
Power Supply Range: Input Voltage Range: 10-28V. 24V for UL294 installations.
Power Consumption: 2.2 Watts + (Input Voltage) * (Reader Current) max.@ 24 VDC;
normally provided by Andover Continuum power supply module.

Overload Protection: 0.5 A resettable fuse with transient voltage suppressor

(TVS) and reverse polarity protection

INPUTS/OUTPUTS

Inputs
Card Readers: 1*
Keypad: 1*
* Only one of these two devices can be active at any given moment.
Card Reader Type: Wiegand, ABA or CardKey (switch selectable) **
Maximum Number 64 (Wiegand)
of bits/Card: 255 (ABA)

Card Reader Power: +5 V (±3%) @50 mA (max.)

Wiring Distance
Card Reader to 500 ft. max. using 18-gauge wire
AC-1 Plus: 200 ft. max. using 22-gauge wire
Alarm Inputs: Up to 5 supervised inputs. Single or double resistor
supervision, series or parallel.
Input Protection: Transient voltage suppressor (TVS) on each input

** The following reader and keypad models are the only approved devices for use in UL 294
Access Control applications:
Essex KTP-163-SN keypad; HID Epic 32985 Wiegand reader; Indala ASR-500 Wiegand reader.

Outputs
Door Outputs: 2 Form C relays
Output Rating: 24 VAC/VDC @ 5 Amp
Reader LED Output: (2) each, open collector; up to 100 mA.
Output Protection: 5000 V isolation 270 V MOVs on each output
Overrides: 3-position manual override switch on each output for
manual control of relay. LED override status indicator.
Override Feedback: Override detection and software feedback provided for
each output.

168 Schneider Electric

 AC-1 Plus

I/O Connections
The actual I/O connections are located on a sixteen-position removable screw terminal
connector located at the bottom of the module. Wires should enter from either the top or
bottom wiring troughs, and outputs should come from the right side of the rack, inputs
from the left (by convention).

The diagram below indicates where each output number is located in the terminal block.

Connection Description

1. Reader +5V
2. Reader GND
3. Reader DATA (Wiegand I)
4. Reader CLK (Wiegand 0)
5. Keypad DATA (Wiegand I)
6. Keypad CLK (Wiegand 0)
7. Reader LED1
8. Reader LED2

9. Earth Ground
10. IN1
11. IN2
12. RET
13. IN3
14. IN4
15. RET
16. IN5

17. OUT1 NC
18. OUT1 NO
19. OUT1 COMM
20. OUT2 NC
21. OUT2 NO
22. OUT2 COMM

Andover Continuum I/O System Reference 169

AC-1 Plus

Using the AC-1 Plus

AC-1 Plus is a complete card access control module designed to interface with the
Schneider Electric NetController where an internal firmware-based Access Control
supervisor resides. During normal operation, access control decisions are made in the
Andover Continuum NetController CPU module database, which provides storage for up
to 75,000 “local” personnel records (up to 4 million records can be created per database).
The AC-1 Plus is designed to control a single door. The door can be configured to allow
entrance based on card only, card plus personal ID number (PIN), or keypad only. The
door’s operating mode can even be changed based on time-of-day or other events for
optimum flexibility through Schneider Electric’s easy-to-use Plain English programming
language. Each keypad can also permit entry of a duress alarm code that can initiate an
alarm sequence at any AC-1 Plus controller or at the Andover Continuum CyberStation.

The AC-1 Plus also supports ADA (Alternate Door Access) and inverted door output
installations and Bond Sensor circuitry. A bond sensor detects the actual status (locked
or unlocked) of the door.

Time-based anti-passback and entry/egress anti-passback are available to prevent

tailgating. Entry/egress anti-passback is system-wide and can be performed by readers
located on different AC-1 and AC-1 Plus controllers across the network.
Using Plain English, the AC-1 Plus can also be used for custom access control
sequences such as two-man rule, optical turnstile control, and man trap configurations.

Reader Power
The AC-1 Plus module supports 5 volt DC readers.

Reader Type Switch

The AC-1 Plus supports three card formats. The Reader Type switch selects either
Wiegand/ABA or CardKey (CK34) format.

170 Schneider Electric

 AC-1 Plus

Degrade Mode
If network communications are interrupted, as a fail-safe mode, the AC-1 Plus will revert
to a programmable degraded mode of operation. System operation during degrade
mode provides uninterrupted card access using site codes, cards formats, and other
degrade mode parameters stored in non-volatile EEPROM (such as the settings of the
AccessLEDPattern Numeric) in each AC-1 Plus module.

Degrade mode parameters are configured from the “Access Validation” section of the
door editor’s “Entry Reader” tab. For dual reader doors, configurable degrade mode
parameters are available from the “Access Validation” section of the door editor’s “Exit
Reader” tab.

During degrade mode, the AC-1 Plus module supports:

ƒ All four site codes entered on the “Card Formats” tab of the door editor
ƒ All card types selected on the “Card Formats” tab of the door editor
ƒ ADA functionality
ƒ General codes (Keypad)
ƒ Door Switch operation on both the Entry and Exit IOU of a dual-reader door

Andover Continuum I/O System Reference 171

AC-1 Plus

Reader LED Pattern

For the AC-1 Plus, the LED pattern of the reader is determined by the creation of an
InfinityNumeric called AccessLEDPattern. The settings are described as follows:

Schneider Electric LED Pattern (AccessLEDPattern = 0)

This pattern is transaction based, meaning the reader LED indicates the state of the
access transaction.

ReaderLED Description
Solid Red No door configured on this reader channel. The
system will not process any transaction coming
from this reader
Solid Green Door configured on this reader channel. System
is ready to process an access transaction (i.e.
card swipe)
Solid Red for 3 seconds Invalid Attempt
following an access transaction
Rapid Flashing following an Valid Access
access transaction
Slow Flashing following an System is waiting for information needed to
access transaction process the transaction. I.e. Transaction is
being processed (remote validation) or the
system is waiting for user entry (PIN needed
after card swipe).

NOTE1: Starting in V1.1, LED2 will turn ON whenever the door is open. This can be
used to control another indicator LED, such as a keypad LED.

NOTE2: A manual override does not affect the Reader LED for the Schneider Electric
LED pattern.

172 Schneider Electric

 AC-1 Plus

Alternate LED Pattern (AccessLEDPattern = 1)

This pattern follows the state of the door lock itself.

ReaderLED Description
Solid Red Door is locked
Solid Green Door is unlocked
Rapid Flashing following an Invalid attempt
access transaction
Slow Flashing following an System is waiting for information needed to process
access transaction the transaction. I.e. Transaction is being processed.
(remote validation) or the system is waiting for user
entry. (PIN needed after card swipe)

NOTE: Starting in V1.1, LED2 will turn ON whenever the door is open. This can be
used to control another indicator LED, such as a keypad LED.

Andover Continuum I/O System Reference 173

AC-1 Plus

CardKey LED Pattern (AccessLEDPattern = 2)

ReaderLED – Red ReaderLED - Green Description

OFF OFF Door is locked
OFF ON Door is unlocked
ON OFF Invalid attempt
Slow Flashing OFF System is waiting for information
following an access needed to process the transaction. I.e.
transaction Transaction is being processed.
(remote validation) or the system is
waiting for user entry. (PIN needed
after card swipe)

NOTE1: The 12V incandescent lamp power is not provided by the AC-1plus.

NOTE2: The RED lamp is controlled by the LED1 output and the GREEN lamp is
controlled by the LED2 output.

174 Schneider Electric

 AC-1 Plus

Dorado780 LED Pattern (AccessLEDPattern = 3)

This LED pattern was designed to be used with the Dorado Model 780 ABA
Reader/Keypad.

“Slide Card” “Enter Code” “Open Door” Description

LED - Red LED – Amber LED – Green
ON OFF OFF Waiting for card swipe
Slow Flashing OFF OFF System is validating the card
swipe
OFF ON OFF Waiting for PIN entry
OFF Slow Flashing OFF System is validating the PIN
entry
OFF OFF ON Door is unlocked
Rapid Flashing Rapid Flashing OFF Invalid attempt

NOTE1: The dipswitches on the Dorado Model 780 must be set for CLOCK/DATA
operation.

NOTE2: The LED1 output on the AC-1plus is wired to the LED A input on the Dorado
Model 780, and the LED2 output is wired to the LED B input.

Andover Continuum I/O System Reference 175

AC-1 Plus

Entering an Input String at a Keypad for Use in PE Programs

From a keypad connected to an AC-1 Plus, you (the user) may also send additional data
to a controller, which in turn passes it to a Plain English (PE) program for execution in an
Andover Continuum control application. This capability enables you to use the keypad to
send input to a PE program for any purpose.

For example:

• A user can enter a string that a PE program uses to turn lights or fans on or off, or to
control other HVAC equipment.
• A user can enter a string indicating the user’s purpose for entering an area. The PE
program can capture this information as input to a PE program for tracking reasons
for activity in a secure area.

Handling String Input at the Controller

Before you can use the keypad for PE program input, you must create a Plain English
program that processes the string entered at the keypad and returns a value to the AC-1
Plus based on the entry. In addition, you must create the following objects in the
controller:

• An InfinityString object that stores the input from channel 7 of the AC-1 Plus and that
your PE program reads to obtain the content of the string
• An InfinityOutput object that stores a numeric value specified in the PE program and
sent to channel 4 of the AC-1 Plus (See “PE Feedback to the AC-1 Plus” later in this
section.)

You can use Continuum Explorer in CyberStation to create the InfinityString and
InfinityOutput objects in the controller.

Entering String Input from Keypad

The process for entering string input at a keypad has the following steps:

1. The user presents a valid access card and/or PIN (if a PIN is required) to the
door reader.
2. The controller for this reader accepts the user’s credentials, and the door
unlocks.
3. Within three seconds of the door unlocking, the user enters two consecutive
asterisks ( ** ) at the keypad to enter escape sequence mode.

176 Schneider Electric

 AC-1 Plus

4. The keypad LED flashes slowly to indicate that it is waiting for input.
5. The user enters a numeric string of up to 30 characters (not including the two
asterisks), and then terminates the string with the pound sign (#).

For example: **10# or **6986310#

6. The AC-1 Plus sends the string to the controller (and its PE program) via
channel 7, the string input channel for Plain English.
Entry Rules for String Input

The following rules apply to using a keypad connected to the AC-1 Plus to enter string
input:

• After the door unlocks, if more than 3 seconds elapse before the user enters two
asterisks, the AC-1 Plus exits escape sequence mode. The user must begin the
process for string input again.

• If a user enters more than 30 characters (not including the first two asterisks), the
AC-1 Plus detects when the 31st digit is entered. The AC-1 Plus then replaces the
30th character with T to indicate Tamper, and sends the string to the controller (no #
is needed). Subsequent characters entered as part of the string are ignored.

For example, if the user enters **123456789012345678901234567890123, the

AC-1 Plus sends **12345678901234567890123456789T to the controller.

• The user can enter asterisks within the string if needed. These asterisks are
converted to periods when sent to the PE program.

For example: 69*8*6310 is converted to 69.8.6310 when sent to the PE program.

• If more than 4 seconds elapse between keystrokes, the AC-1 Plus exits escape
sequence mode. The user must begin the process for string input again.

• If a user presents an access card to the card reader while the AC-1 Plus is in escape
sequence mode, the AC-1 Plus exits escape sequence mode. The user must begin
the process for string input again.

Andover Continuum I/O System Reference 177

AC-1 Plus

PE Feedback to the AC-1 Plus

After the PE program receives the string input and interprets its value, the program
assigns an appropriate value to the InfinityOutput object. One of the following values is
transmitted back to the AC-1 Plus through channel 4:

ƒ 1 – Clear string.

ƒ 2 – Recognize the escape sequence entry (success).

ƒ 3 – Do not recognize the escape sequence entry (fail).

NOTE: Clearing the string in the AC-1 Plus using the Clear String command is
recommended after each string input in escape sequence mode.

Based on the numeric value returned to the AC-1 Plus through channel 4, the AC-1 Plus
also uses the reader LEDs to indicate to the user whether or not the string input is valid
or invalid. The LED pattern to indicate valid/invalid entry is the same as the selected
access control LED pattern used to indicate valid/invalid card and PIN entry.

178 Schneider Electric

 AC-1 Plus

Connecting a Reader/Keypad
Reader/Keypad Inputs
The AC-1 Plus includes a full interface to a single Wiegand, ABA or CardKey access card
reader. The module is designed to allow Integral reader/keypad units to be connected
directly. Separate keypads that have similar interfaces can be connected in parallel with a
reader by using the auxiliary input connector as shown on the following page.

The reader and/or reader/keypad unit is connected to the AC-1 Plus module as shown
below:

5V

GND

+V
GND
Reader DATA / I
DATA I
or
Reader with Keypad DATA 0
LED

CLK / 0

LEDx

Andover Continuum I/O System Reference 179

AC-1 Plus

Connecting Two Readers or a Keypad and a Reader

The AC-1 Plus can interface to both a keypad and a reader simultaneously. This
assumes that they are both format compatible devices of similar voltage range.

Similarly, two readers can be connected. This allows a site to slowly introduce a different
type of reader (i.e., proximity) while allowing access through the normal reader.
AC-1 Plus

1 5V

2 GND

+V
GND
Reader
LED
or
Reader with Keypad DATA 1
or Keypad only CLK 0
7 LED1

3 DATA / I

4 CLK / 0

5 DATA / I

6 CLK / 0

8 LED2

DATA 1
CLK 0
Reader LED
or
GND
Reader with Keypad
or Keypad only +V

180 Schneider Electric

 AC-1 Plus

Connecting a CardKey Reader

You can connect a CardKey reader directly to the AC-1 Plus, however, the CardKey
reader requires a +12VDC supply for the red and green lamps. The AC-1 Plus does not
supply 12 VDC, therefore it is necessary to connect an external power supply to provide
the necessary power for the lamps.

Make sure the reader type switch is set to the CK34 position when using a CardKey
reader.

Andover Continuum I/O System Reference 181

AC-1 Plus

Connecting Two Readers for a Dual Reader Door

With the addition of another AC-1 Plus module, a door can be configured as a dual
reader door. A door is a dual reader door when it has been configured with an entry and
exit IOU module.

A dual reader door is connected as shown below:

AC-1 Plus Entry IOU

* Door
Supervised Input
Termination
IN2 Switch
Entry Reader Reader

*
Alarm Supervised Input Bond
Termination
Out Out2 IN1 Sensor

Out1

Door
Strike

AC-1 Plus Exit IOU

*
Supervised Input
Termination
IN2
Exit Reader Reader

*
Supervised Input
Termination
IN1

Out1

* TERMINATION
Each input must be terminated using your chosen Supervised
Input resistor arrangement. It is important that BOTH AC-1 Plus
modules include termination where they share door switches
and/or Bond sensors.

For more information on input termination, refer to the section on

Supervised Inputs.

182 Schneider Electric

 AC-1 Plus

Connecting Supervisory Inputs

All AC-1 Plus inputs are supervisory inputs. The following drawings depict the three types
of supervisory inputs that exist—two normally closed and one normally open type.

NOTE: All resistor values are to be 10KΩ ± 5%.

Normally Closed Supervised Inputs

NC Series
With this type of input wiring, a resistor is placed in series with the input being monitored.
When the input contact presents a short circuit (normal closed position) the input is
assumed in a normal closed state, the circuit presents a reading of 10 KΩs at the input.

Circuit Action Input Senses Condition

Switch Closed External Resistance Input contact Closed
Switch Opened Infinite Resistance Input contact Open
Wire Cut Infinite Resistance Input contact Open ‘Violation’
Input Shorted Zero Ωs Violation or error

When the input contact is opened, the circuit opens and an infinite resistance is
measured. If the wires to the input contact are cut it also appears as an “input contact
open” condition. In this case there would be a input contact open without a valid card
swipe or valid keypad entry resulting in an “input contact violation”. Shorting the input
causes a zero Ω resistance, which also results in an input contact violation.

When configuring for this type of contact select:

ElecType: Supervised
Resistor Type: NCSeries

Andover Continuum I/O System Reference 183

AC-1 Plus

Normally Closed Supervised Inputs

NC Series Parallel
With this type of input wiring, two external resistors are added to the input, one in series
and the other in parallel. When the input contact switch is closed (normal position) the
input contact is assumed to be closed. The circuit presents a reading composed of both
resistances in parallel that works out to be half the value of one of them (5 KΩ).

Circuit Action Input Senses Condition

Switch Closed External Resistance ÷ 2 Input contact Closed
Switch Opened External Resistance Input contact Open
Wire Cut Infinite Resistance Violation or error
Input Shorted Zero Ωs Violation or error

When the input contact is opened the switch opens and the value of the parallel resistor
is measured. If the wires to the input contact are cut it appears as an infinite resistance.
Shorting the input causes a zero Ω resistance. Both a short and an infinite resistance
(open) should result in an error condition.

When configuring for this type of contact select:

ElecType: Supervised
Resistor Type: NCSerPar

184 Schneider Electric

 AC-1 Plus

Normally Open Supervised Inputs

NO Series Parallel
With this type of input wiring, two external resistors are added to the input, one in series
and the other in parallel. When the input contact switch is open (normal position) the
input contact is assumed to be closed. The circuit reads the value of the parallel resistor.

Circuit Action Input Senses Condition

Switch Closed External Resistance ÷ 2 Input contact Open
Switch Opened External Resistance Input contact Closed
Wire Cut Infinite Resistance Violation or error
Input Shorted Zero Ωs Violation or error

When the input contact is opened the switch closes and a reading results that is
composed of both resistances in parallel that works out to be half the value of one of
them (5 KΩ). If the wires to the input contact are cut it appears as an infinite resistance.
Shorting the input causes a zero Ω resistance. Both a short and an infinite resistance
(open) should result in an error condition.

When configuring for this type of contact select:

ElecType: Supervised
Resistor Type: NOSeriPar

Andover Continuum I/O System Reference 185

AC-1 Plus

Wiring Door Switches

There are three supervisory inputs for door switches. The maximum length wire you may
use is 500 ft of #18 gauge wire (152 m of 1.0 mm2 wire) or 200 ft of #22 gauge wire (60
m of 0.35 mm2 wire).
Some switches have built-in resistors that facilitate Series Parallel connections as shown
below:

Switch with AUX

Built-In Resistor or
DOOR
or
REX

10 KΩ

RET

Wiring Motion Detectors

Motion detectors are devices that close a switch contact when motion is detected.

Wiring is similar to a normal door switch input, however, the motion sensor requires an
external power supply of 12 VDC or 24 VDC (UL listed under APHV). The maximum
length wire you may use is 500 ft of #18 gauge wire (152 m of 1.0 mm2 wire) or 200 ft of
#22 gauge wire (60 m of 0.35 mm2 wire).

The following shown a typical motion detector circuit:

No AUX
Motion or
Detected DOOR
or
REX
Normally Open 10 KΩ
PIR Motion
Detector

RET

Motion AUX
Detected or
DOOR
or
REX
Normally Open 10 KΩ
PIR Motion
Detector

RET

186 Schneider Electric

 AC-1 Plus

Connecting Outputs
The AC-1 Plus module includes two Form C single-pole double-throw relay outputs. The
following is a simplified schematic of each output channel:

OUT x NC

OUT x NO

OUT x COM

Both channels resemble the circuit shown above.

To use the Form C output in your system, configure an output point with an Electrical
Type of Digital.
These output contacts operate as a standard relay. When the output is set to an “ON”
state, the normally open contacts close and the normally closed contacts open.
Note: When configuring a Digital point, there is a “‘Polarity” attribute. If this attribute is
enabled, the operation of the outputs are reversed.

Override Controls
The AC-1 Plus module includes an output override switch for each output.

ON

OFF

AUTO

The output of the module can be directed from program control or manual control. The
output can be disabled completely as well.

Andover Continuum I/O System Reference 187

AC-1 Plus

The following describes the actions associated with each position of the override controls:

ON The output relay is energized to an “ON” state manually by

setting the switch to ON. Programs have no effect on the output
when the switch is in this position.

OFF The output relay is de-energized to an “OFF” state manually by

setting the switch to OFF. Programs have no effect on the output
when the switch is in this position.

AUTO The action of the output relay is determined as a direct result of

program control.

Wiring Door Outputs

The following represents a typical door output installation when the circuit is normally
open:

MOV
(Andover #01-2020-095)

C
Door Strike
(UL listed burglary-resistant
electric locking mechanism (CVXY))

12/24V

Power Supply
(UL listed power supply (APHV))

This configuration shows a normally de-energized lock (when secured) in a fail secure
mode. If power loss occurs, the lock closes. Always be sure to use “panic” hardware that
allows emergency exit from the secured area.

188 Schneider Electric

 AC-1 Plus

The following represents a typical door output installation when the circuit is normally
closed:
MOV
(Andover #01-2020-095)

Electromagnetic Door Lock

(UL listed burglary-resistant
electric locking mechanism (CVXY))

12/24V

Power Supply
(UL listed power supply (APHV))

This configuration shows a normally de-energized lock (when secured) in a fail safe
mode. If power loss occurs, the lock opens.

Andover Continuum I/O System Reference 189

AC-1 Plus

Wiring Dual Reader Door Outputs

The following represents a typical door output installation when the dual reader door
circuit is controlling a fail-safe lock:

Exit IOU

Entry IOU

MOV
(Andover #01-2020-095)

C
Door Strike
Fail-Safe
(UL listed Door Lock
burglary-resistant
(Energize
electric to lock)
locking mechanism (CVXY))
UL-listed burglary-resistant
Electric locking mechanism (CVXY)

12/24V

Power Supply
(UL listed power supply (APHV))

190 Schneider Electric

 AC-1 Plus

The following represents a typical door output installation when the dual reader door
circuit is controlling a fail-secure lock:

Exit IOU

MOV
(Andover #01-2020-095)
Entry IOU

Electromagnetic
Fail-Secure Door Lock
Door Lock
(UL listed
(Energize toburglary-resistant
unlock)
electric locking mechanism
UL-listed burglary-resistant (CVXY))
Electric locking mechanism (CVXY)

12/24V

Power Supply
(UL listed power supply (APHV))

Andover Continuum I/O System Reference 191

AC-1 Plus
Status/Control Panel
Status Indicators
The AC-1 Plus module includes a complete indicator status panel on the front of the module.

This panel includes indicators reporting on the status of the following:

POWER This green indicator illuminates when DC power is applied through the
I/O Bus.
COMM This yellow indicator illuminates when data is transmitted from the
module to the NetController. In normal operation, data is only transmitted
when an input value changes.

This indicator will also flash periodically as the NetController checks the
I/O bus.
OVERRIDE This red indicator illuminates whenever any of the override switches is in
a position other than AUTO.
STATUS This red indicator is normally off. If it is always on or flashing at a fast
rate, there is a problem with the module.

This indicator can be manually illuminated from the CyberStation

workstation or Command Terminal and used as a troubleshooting aid
when locating a particular module.
OUTPUT These red indicators (one for each channel) illuminate when an output
relay is energized.
READER This green indicator illuminates when +5VDC power is available to the
POWER reader.

This panel also includes two operator switches that perform the following:

COMMISSION After physical installation and during configuration through the

CyberStation workstation or Command Terminal, pressing this button
registers the module’s address with the system. For more information,
refer to the section on Module Configuration found earlier in this manual.
RESET If the module becomes inoperable, pressing this button resets the
module. It does not erase its memory.

192 Schneider Electric

 VS-8-4

VS-8-4, VS-8-4-T
Video Switcher
The VS-8-4, Andover Continuum’s video switcher module, includes eight input channels
and four high-speed, buffered, output channels. Any one of the eight input lines can be
connected to any of the four outputs. Each output has a gain of two and is capable of
driving 75 Ω, back-terminated, lines.

The VS-8-4 is an I/O module used with the Andover Continuum Product line and can be
integrated into systems requiring video security. Up to eight surveillance, cameras can be
connected to the VS-8-4 inputs. The VS-8-4 video output can then be connected directly
to a video monitor or other video display or recording device.

The VS-8-4-T version provides the capability of time/date stamping the video signal. In
addition, a title may be added to the video signal to identify the area where the camera is
being directed.

FEATURES

• Eight (8) Video inputs

• Four (4) Video outputs
• Any one input can be connected to
any of the four outputs
• 10–28 V Power Supply Range

Andover Continuum I/O System Reference 193

VS-8-4

SPECIFICATIONS
ELECTRICAL
Power Supply Range: Input Voltage Range: 10-28V. 24V for UL294 installations.
Power Consumption: 2 Watts (83 mA) @ 24 VDC (max.); provided by Andover
Continuum power supply module.

Overload Protection: 0.5 A resettable fuse with transient voltage suppressor

(TVS) and reverse polarity protection.

INPUTS

Impedence: 75 Ω
Connection: BNC connector
Bandwidth (-3dB): > 75 MHz (Rload=150 Ω)

Single Channel
Crosstalk: > -60 dB @ 10 MHz.
All Channel
Crosstalk: > -50 dB @ 10 MHz.
All Channel
Off Isolution: > -55 dB @ 10 MHz.

OUTPUTS

Impedence: 75 Ω
Connection: BNC connector
Signal: 2V pk/pk

194 Schneider Electric

 VS-8-4

I/O Connections
The video input and output connections are located on the bottom of the module.

A quick disconnect spade lug connector allows for an Earth ground connection.

The diagram below indicates where each input and output is located on the module.
These connections are also listed below.

VIDEO OUTPUTS

Earth Ground
1 2 3 4

1 2 3 4 5 6 7 8

VIDEO INPUTS

Standard BNC connections are used for each input and output.

Andover Continuum I/O System Reference 195

VS-8-4

Programming/Use

Video Switching
The outputs of the VS-8-4 module can have up to eight input sources. These outputs are
represented as Numerics in the system. Entering a value of 1–8 selects the input source
for the particular output. Values other than 1–8 turn off the video for that output. Refer to
the programming table on the following page for specifics.

Configure each video output point with an Electrical Type of Numeric.

Title & DateTime Programming (VS-8-4-T Only)

The VS-8-4-T version of the switch provides the capability of superimposing the time/date
and a textual title over the video signal of each output. The video area is divided into
twelve “lines” where this information can be displayed. Line one is at the top of the
screen, line twelve is at the bottom.

The position of the date and time for all outputs is specified as a line numbered 1 though
12. Values other than 1–12 turn off the display of the datetime.

The VS-8-4-T updates the Date and Time automatically, however, it is only accurate to
1.5 seconds per hour. You can send updated datetime readings to the unit though Plain
English.

Titles consist of one line composed up to 24 characters. Receiving more than 24

displays only the first 24 received. Text consists of white characters of 12 (horizontally)
by 18 (vertical) dots (pixels). The character set supported includes all Alphanumeric
(upper and lower case A–Z, 0–9) characters plus the following punctuation symbols:
, ;
- <
. >
/ ?
:
The display position of the title text is specified as a line numbered 1 though 12. Values
other than 1–12 turn off the display of the title.
Refer to the programming table on the following page for specifics.

196 Schneider Electric

 VS-8-4

VS-8-4-T Configuration Programming Table

Function Channel Object Direction Values

Type
Video Select Output 1 1 Numeric IOOutput 1–8 ; corresponding to input
channel number.
Other values turn off this output.
Video Select Output 2 2 Numeric IOOutput 1–8 ; corresponding to input
channel number.
Other values turn off this output.
Video Select Output 3 3 Numeric IOOutput 1–8 ; corresponding to input
channel number.
Other values turn off this output.
Video Select Output 4 4 Numeric IOOutput 1–8 ; corresponding to input
channel number.
Other values turn off this output.

Date/Time Position 5 Numeric IOOutput 1–12 ; corresponding to display

(All four outputs) line number.
Other values turn off the display
of datetime.
Title Position 6 Numeric IOOutput 1–12 ; corresponding to display
(All four outputs) line number.
Other values turn off the display
of the title.

Set Datetime 7 DateTime IOOutput Used to send Datetime to VS-8.

See text.

Title Text Input Source 1 8 String IOOutput Up to 24 characters

Title Text Input Source 2 9 String IOOutput Up to 24 characters
Title Text Input Source 3 10 String IOOutput Up to 24 characters
Title Text Input Source 4 11 String IOOutput Up to 24 characters
Title Text Input Source 5 12 String IOOutput Up to 24 characters
Title Text Input Source 6 13 String IOOutput Up to 24 characters
Title Text Input Source 7 14 String IOOutput Up to 24 characters
Title Text Input Source 8 15 String IOOutput Up to 24 characters

Andover Continuum I/O System Reference 197

VS-8-4

Status/Control Panel
Status Indicators
The VS-8-4 module includes a complete indicator status panel on the front of the module.

This panel includes indicators reporting on the status of the following:

POWER This green indicator illuminates when DC power is applied through the
I/O Bus.
COMM This yellow indicator illuminates when data is transmitted from the
module to the NetController. In normal operation, data is only transmitted
when an input value changes.

This indicator will also flash periodically as the NetController checks the
I/O bus.
STATUS This red indicator is normally off. If it is always on or flashing at a fast
rate, there is a problem with the module.

This indicator can be manually illuminated from the CyberStation

workstation or Command Terminal and used as a troubleshooting aid
when locating a particular module.
INPUTx Each input includes four red indicators (one for each output channel).
Illumination indicates a connection between input and output.

This panel also includes two operator switches that perform the following:

COMMISSION After physical installation and during configuration through the

CyberStation workstation or Command Terminal, pressing this button
registers the module’s address with the system. For more information,
refer to the section on Module Configuration found earlier in this manual.
RESET If the module becomes inoperable, pressing this button resets the
module. It does not erase its memory.

198 Schneider Electric

 VT-1

VT-1
Voice Telecom Module
The VT-1, Andover Continuum’s voice-output/touch-tone input telecom module, provides
users with easy-to-use remote data entry capabilities for their Andover Continuum system
using the familiar touch-tone keypad on any standard or cellular telephone. The VT-1
provides built-in prompt messages and pre-recorded vocabulary words, which can be
used individually or combined to form phrases and sentences. In addition, custom
messages (up to 3 minutes total) can be pre-recorded to inform the user of building
conditions and/or to prompt the user for additional input.

FEATURES

• Provides a Telephone Command

Interface to Andover Continuum
• Accepts DTMF menu selection
• Standard RJ-11 Telephone Interface
• Recording via Telephone
• Dial Out and Call Progress
Capability

Andover Continuum I/O System Reference 199

VT-1

SPECIFICATIONS
ELECTRICAL
Power Supply Range: Input Voltage Range: 20-26V.
Power Consumption: 1.5 Watts (63 mA) @ 24 VDC (max.); provided by
Andover Continuum power supply module.

Overload Protection: 0.5 A resettable fuse with transient voltage suppressor

(TVS) and reverse polarity protection.

INPUTS

Interface: Local Telephone System Interface

Connection: RJ-11 connector

200 Schneider Electric

 VT-1

Telephone Line Connection

The VT-1 connects to the local telephone line via an internal RJ-11 jack.

To install the telephone line, open the cover of the module and plug an RJ-11 cable into
the jack located at the lower left as indicated below.

Connect the other end of the cable to a local telephone jack.

Andover Continuum I/O System Reference 201

VT-1

Programming/Use

Technical Description
The VT-1 module acts as an interface to the Andover Continuum system by allowing a
user to control functions via telephone. It can be configured to operate like an auto
attendant for a telephone system. As the phone line is answered, a series of voice
prompts are played indicating various options that may be selected by pressing touch
tone (DTMF) keys on the caller’s telephone. The DTMF numbers received by the module
represent a desired command or function. The module is equipped to decode the DTMF
responses and send them off to an attending controller.

The module can also be commanded to dial out and provide callback numbers to a
paging system.

The VT-1 operates in either of two modes:

Supervisor Mode
Supervisor Mode provides a method for recording the messages that may be played back
at a later time. These messages may be application specific phrases that the controller
can select for communicating with the user. It is these messages that are played to
inform the caller of the various control options available.

User Mode
User mode is the normal operating mode of the VT-1. In this mode, the VT-1 is under the
control of a Plain English program. When a user calls into the module, messages are
played and touch-tone digits are captured.

202 Schneider Electric

 VT-1

There are three types of voice messages within the VT-1:

Type of Message

SUPERVISOR PROMPT MESSAGES

Not accessible by the user, strictly for
Supervisor Mode
Approximately 30 seconds

PRE-RECORDED MESSAGES
Words and sentence fragments that can be
played in both User and Supervisor Mode
Approximately 80 seconds

USER RECORDED MESSAGES

Custom user messages that can be recorded,
played and erased in Supervisor Mode. Available
for playback only in the User Mode.
Record Time = Approx. 190 sec ( 3 min))

Operation
The VT-1 includes several pre-recorded words and phrases. It is not necessary that you
record new messages. If you intend to use these pre-recorded words, there is no need to
enter Supervisor Mode.

Security
Because the VT-1 allows connection to your system via a standard telephone line, we
have included a password-based security lock to allow controlled access to its operation.
Both User and Supervisor modes have their own passwords. These passwords can be
changed at any time simply by editing a value stored in a Plain English numeric variable.

The system can easily monitor VT-1 activity. Whenever a user successfully logs into the
VT-1 (correct password entered), a status code appears in one of the module’s numeric
objects.

VT-1
Andover Continuum I/O System Reference 203
 VT-1
VT-1

Supervisor Mode
The Supervisor Mode allows you to record a number of custom messages that can be
selected for playback at strategic times through your program.

Entering Supervisor Mode

To enter this mode, make sure the VT-1 is connected properly to a working telephone
line and is powered. From any telephone, call the number associated with the line
attached to the VT-1. As the line rings the module, the VT-1 responds by answering the
line (going “off-hook”). The Off Hook indicator on the front panel illuminates.

Message number 1 is played: “Enter password followed by the pound key.”

At this time you are expected to press a four-digit password followed by the pound (#)
button to access the unit. The default Supervisor mode password is 1234. As indicated
earlier, this password can easily be changed.

If you enter the wrong password, the VT-1 responds with Message 2: “Invalid password.”
The unit then allows you to try again. In any case, if the module does not receive the
correct password in 30 seconds, the VT-1 disconnects the call.

Once the correct password is received, the module plays Message 3: “Press 1 to record,
2 to play or 3 to erase a message. Press star to exit.” This is referred to as the main
menu. From here you can access its supervisory functions.

Note: In this mode, the VT-1 will automatically hang up if no DTMF activity has
been received for 30 seconds.

Exiting Supervisor Mode

To exit Supervisor mode, press the star (*) button on your telephone when you are at the
“main menu prompt”. This disconnects the VT-1 from the phone line causing the Off Hook
indicator to extinguish.

Alternatively, hanging up on the module will exit the mode as well.

204 Schneider Electric

 VT-1

Supervisor Functions
The messages that you can record, play and erase are stored in separate locations
denoted by their “message number”. Custom messages occupy message numbers 1-
150. Although there appears to be 150 possible custom messages, the limit is actually
the amount of time your entire message library requires. The VT-1 allows for a total of
approximately 3 minutes of custom recording time. Therefore, the total number of
messages you can record cannot exceed the 3 minute limit.

When all available message space is filled, the VT-1 will not allow subsequent recording.
The message: “Voice memory full” is played. To allow further recording, erase unused
messages.

Record Message Mode (Press 1)

Pressing the 1 button allows you to record a voice message. Message 4 plays: “Enter
message number followed by the pound key. Press star to return to the main menu.”

1 Enter a new message number in the range 1–150.

Message #'s need not be consecutive. If that number has been used previously,
a message: “Invalid entry” is heard. To record over an existing message, you
must first erase that message.
Enter multiple digit numbers simply by pressing them in order e.g. “125”.
2 Press the pound (#) button to begin recording. Begin speaking after the tone.
Note: Due to the internal time-out of the VT-1, an individual message
cannot exceed 29 seconds.
3 Once you have finished speaking the message, press any button to terminate
recording. The VT-1 responds with the message: “Message recorded.”

At this point you are returned to the main menu where you can select another operation.

Pressing the star (*) button exits the mode and returns the VT-1 to the “main menu”
prompt.

Note: Recorded messages are stored in non-volatile memory within the VT-1 and are
therefore preserved (not lost) during power outages.

Andover Continuum I/O System Reference 205

VT-1

Playback Message Mode (Press 2)

Pressing the 2 button allows you to play a recorded voice message. Message 4 plays:
“Enter message number followed by the pound key. Press star to return to the main
menu.”

1 Enter a message number in the range 1–230.

If the message number does not contain a message, a message: “Invalid
entry” is heard.
Enter multiple digit numbers simply by pressing them in order e.g. “125”.
2 Press the pound (#) button to begin playback.
In this mode you can play both custom user-recorded messages and the pre-recorded
words and phrases stored in the VT-1. The pre-recorded words and phrases are listed
along with their message numbers later in this section.

After the message finishes playing, you are returned to the main menu where you can
select another operation.

Pressing the star (*) button exits the mode and returns the VT-1 to the “main menu”
prompt.

Erase Message Mode (Press 3)

Pressing the 3 button allows you to erase a recorded voice message. Message 4 plays:
“Enter message number followed by the pound key. Press star to return to the main
menu.”

1 Enter a new message number in the range 1–150.

If the message number does not contain a message, a message: “Invalid
entry” is heard.
Enter multiple digit numbers simply by pressing them in order e.g. “125”.
2 Press the pound (#) button to erase. The VT-1 responds with the message:
“Message erased.”

At this point you are returned to the main menu where you can select another operation.

Pressing the star (*) button exits the mode and returns the VT-1 to the “main menu”
prompt.

206 Schneider Electric

 VT-1

User Mode
The User Mode is the normal operating mode of the VT-1. In this mode your Plain
English program communicates to the user through the VT-1’s pre-recorded voice
messages and receives commands from the user via telephone button entries.

Entering User Mode

To enter this mode, make sure the VT-1 is connected properly to a working telephone
line and is powered. From any telephone, call the number associated with the line
attached to the VT-1. As the line rings the module, the VT-1 responds by answering the
line (going “off-hook”). The Off Hook indicator on the front panel illuminates.

Message number 1 is played: “Enter password followed by the pound key.”

At this time you are expected to press a four-digit password followed by the pound (#)
button to access the unit. The default User mode password is 4321. As indicated earlier,
this password can easily be changed.

If you enter the wrong password, the VT-1 responds with Message 2: “Invalid password.”
The unit then allows you to try again. In any case, if the module does not receive the
correct password in 30 seconds, the VT-1 disconnects the call.

Once the correct password is received, the module sends a code to the controller through
a numeric point indicating that it has been accessed by a user.

Exiting User Mode

The only way to exit this mode is for your program to stop operating in the User mode
and to send the hang up command to the module. If the caller hangs up, the program
should be designed to include a method of monitoring inactivity such as a timeout.

Andover Continuum I/O System Reference 207

VT-1

Configuration

Your system controller communicates to the VT-1 through a series of points. The
following is a table of the points that must be defined before you can use the module.

VT-1 Configuration Programming Table

Function Channel Object Type Direction Values

VT State 1 Numeric I/O Input 100 Supervisor Password

Entered
110 User Password Entered
200 VT-1 Off-Hook
201 Dial Tone Present
202 Ring Signal Present
203 Busy Signal Present
204 Ringing Stopped (Phone
picked up)
205 Dial Out Complete
300 Attempted to Play an
Invalid Message number.
301 Message has completed
playing.
302 Message is still playing.
User Response 2 String [30] I/O Input String of user generated DTMF
responses. (max 30 char)
Supervisor 1 Numeric I/O Output 0-9999 (4 digits max)
Password
User Password 2 Numeric I/O Output 0-9999 (4 digits max)

Ring Count 3 Numeric I/O Output 1-255 (Default =1)

Command 4 Numeric I/O Output 8000 Dial Out

8001 Hang Up
8002 Single Tone Mode
8003 Multi -Tone Mode
Dial Out Phone 5 String [15] I/O Output Hayes compatible digits and
Number pause characters (15 max)

Play Message 6 String [30] I/O Output Semicolon separated list of

Message numbers for VT-1
concatenation.
(30 character limit)

208 Schneider Electric

 VT-1

VT State
This Numeric input indicates the current state of the VT-1. The value contained in the
numeric changes as the VT-1 operates. The various states that can be monitored are as
follows:

Password Access As the VT-1 is accessed, this numeric indicates when a

successful password has been entered for either Supervisor
mode (100) or User mode (110).
General Access Whenever the VT-1 answers or originates a call, it accesses
the telephone line by going “off-hook”. This action is reported
by a code of 200.
Call Out Progress The VT-1 has the capability of making a call to another
telephone, paging system or other equipment. During the
process of calling this outside number the status of the call is
reported through a series of codes:
201 Dial tone detected
202 Ring tone detected
203 Busy Signal detected
204 Ring Signal Stop (call was answered)
Dial Out Progress The VT-1 has the ability to dial a DTMF number after it calls
an outside system. This operation is typical of paging systems
where you call the paging system number, wait for the prompt
and then enter the phone number you want the paging party
to call. When used in this mode, the VT-1 reports when it is
done sending the number through the code of 205.
Message Playback The VT-1 reports when an invalid message number has been
entered for playback (code 300). When a valid message is
finished playing, the VT-1 reports a code of 301. When a
message is in progress, the VT-1 reports a code of 302.

Andover Continuum I/O System Reference 209

VT-1

User Response
This String contains the values of the buttons pressed by the user in response to a
prompt. In Single Tone Mode, this value would be a single character. If the caller pressed
the 3-button, the String would contain the 3. In Multi-Tone Mode, the String contains all
the buttons pressed. If the caller pressed 234, the String contains the series of characters
234.

Passwords (Supervisor & User)

These Numeric inputs contain the passwords for Supervisor and User access to the VT-
1. Passwords are entered by the caller as a series of numbers, however, the password
itself is represented as one number in the numeric.

For example, the default password for Supervisor mode is 1234. The caller presses four
buttons to enter this series of numbers: 1-2-3-4. The numeric contains the number 1234.

If you want a three-digit password (e.g., 265), enter the number 265 into the Numeric.

The largest number you can enter into either password numeric is 65535. Passwords can
be a maximum of four digits in length. If a five-digit value is entered, the most significant
digit is discarded. (e.g., 65535 becomes 5535)

Ring Count
This Numeric determines how many rings the VT-1 will await before it answers a call. The
default is 1, however you can set it to any number up to 255.

Command
This Numeric allows you to set the mode in which you expect user responses to occur
and it allows you to hang up the line or dial out. These actions are done by entering a
code into this numeric as follows:
Code Action
8000 Dial Out
8001 Hang Up
8002 Single-Tone Mode
8003 Multi-Tone Mode

210 Schneider Electric

 VT-1

Command Summary
Single-Tone Mode is used when you want the user to press only one digit in response to
your prompt. This mode is appropriate for menu choices when you “Press 1 for
something, 2 for another…”.

Multi-Tone Mode is used for entering values. When in this mode, the VT-1 gathers
responses until the caller presses the pound (#) button. Therefore, if you are expecting
the caller to enter a temperature setpoint such as 23 degrees, the caller would press 2-3-
#. If you use this mode, be sure to inform your operator in your voice prompt of the need
to press the pound button.

Dial Out is used when you want to use the VT-1 to dial an outside number in response
from some user input. Entering this command causes the VT-1 to go “off-hook”, detect
dial tone and dial the number contained in the Dial Out Phone Number string.
Hang Up terminates a dial out operation or a user operation.

Dial Out Phone Number

This String contains the phone number of the outside number you wish the VT-1 to call.
Commas entered in this string indicate 2-second delays. A maximum of 15 digits can be
entered in this string.
DTMF tones may be generated while off hook in the User Mode. This is intended for
pager interface. To use this feature, your Plain English program, after dialing the pager
phone number and receiving the Ringing Stopped value (204) in the VT State object,
would enter a new phone # to this string. This new number is the desired number to be
left with the pager provider. The program would then wait a predefined number of
seconds and then, on a separate line label*, would load the value of 8000 (DIAL OUT)
into the Command Numeric object. The VT-1 generates the phone number and reports
back a value of 205 (DIAL OUT COMPLETE) to let the program know that the phone
number DTMF tones have been generated and it is now safe to hang up (go on hook).
The Plain English program would then send the HANG UP command (8001).

NOTE: The VT-1 cannot detect the typical pager system beeps to signify the pager
system is ready to accept the phone number. The user must know the time delay to wait
prior to sending the DIAL OUT command after the Ringing Stopped event is received.
• Including the number and the command numeric in a single Plain English line may cause
timing problems resulting in errant numbers being sent.

Andover Continuum I/O System Reference 211

VT-1

Play Message
This String contains the message number of a pre-recorded message for playing. Setting
this string to a valid message number starts the VT-1 playing the desired message. When
the message is finished, the VT-1 reports this fact through a code of 301 in the VT State
numeric. If the message number is an invalid one, the VT-1 reports a code 300.

You can concatenate (string-together) several messages using this string. Entering
message numbers separated by a semicolon (;) automatically concatenates the
messages within the VT-1. This is an easy way of creating sentences from the multitude
of prerecorded words and phrases found in messages 151-230.
Example:

To play the phrase “The Temperature is seventy five degrees”, the user must
concatenate pre-recorded message #’s 181,175,155, and 184 respectively. This yields
the following Plain English code:

VTPlaymessage = “181;175;155;184”

Important Note:
There is a limit to the number of characters the Play Message string can handle.
You must limit the number of characters to 30.

The example message yields a total character count of 15 (one per digit).

212 Schneider Electric

 VT-1

Pre-Recorded Voice Message List

Supervisor Prompt Messages

Message Number Message
1 Enter password followed by the pound key.
2 Invalid password.
3 Press 1 to Record, 2 to Play or 3 to erase a message. Press *
(star) to exit.
4 Enter message number followed by the pound key. Press * (star)
to return to the main menu.
5 Invalid entry.
6 Message recorded.
7 Message erased.
8 Goodbye.
9 Voice Memory Full.

Pre-recorded Words & Phrases

Message Number Message
151 One
152 Two
153 Three
154 Four
155 Five
156 Six
157 Seven
158 Eight
159 Nine
160 Ten
161 Eleven
162 Twelve
163 Thirteen
164 Fourteen
165 Fifteen
166 Sixteen
167 Seventeen
168 Eighteen
169 Nineteen
170 Twenty
171 Thirty

Andover Continuum I/O System Reference 213

VT-1

Pre-recorded Words & Phrases (continued)

Message Number Message
172 Forty
173 Fifty
174 Sixty
175 Seventy
176 Eighty
177 Ninety
178 Hundred
179 Thousand
180 Point
181 The Temperature is
182 The Humidity is
183 Percent
184 Degrees
185 Fahrenheit
186 Celsius
187 The Set point is
188 Press 1 for yes or 2 for no.
189 Press
190 To change
191 Set point
192 Temperature
193 Humidity
194 Enter
195 Followed by the pound key
196 Alarm
197 Condition
198 Security
199 Access
200 Password
201 Invalid
202 Entry
203 Code
204 Hello
205 Please
206 Plus
207 Minus
208 Heat
209 Cool

214 Schneider Electric

 VT-1

Status/Control Panel
Status Indicators
The VT-1 module includes a complete indicator status panel on the front of the module.

This panel includes indicators reporting on the status of the following:

POWER This green indicator illuminates when DC power is applied through the
I/O Bus.
COMM This yellow indicator illuminates when data is transmitted from the
module to the NetController. In normal operation, data is only transmitted
when an input value changes.

This indicator will also flash periodically as the NetController checks the
I/O bus.
STATUS This red indicator is normally off. If it is always on or flashing at a fast
rate, there is a problem with the module.

This indicator can be manually illuminated from the CyberStation

workstation or Command Terminal and used as a troubleshooting aid
when locating a particular module.
RECORD This red indicator illuminates when the VT-1 is recording a message.
PLAY This red indicator illuminates when the VT-1 is playing a message.
ERASE This red indicator illuminates when the VT-1 is erasing a message.
RING This red indicator illuminates when the VT-1 is receiving a ring tone from
the telephone line.
OFF HOOK This red indicator illuminates when the VT-1 answers the phone line or
goes “off hook” to make a call.

Andover Continuum I/O System Reference 215

VT-1
VT-1

This panel also includes two operator switches that perform the following:

COMMISSION After physical installation and during configuration through the

CyberStation workstation or Command Terminal, pressing this button
registers the module’s address with the system. For more information,
refer to the section on Module Configuration found earlier in this manual.
RESET If the module becomes inoperable, pressing this button resets the
module. It does not erase its memory.
VT-1

216 Schneider Electric

Andover Continuum I/O System Reference
 Andover Continuum I/O System Reference
Document Number 30-3001-499
Rev. K

30-3001-499 Andover Continuum I/O System Reference