CS3591-Computer Networks Department of CSE 2022-2023

UNIT I INTRODUCTION AND APPLICATION LAYER

Data Communication - Networks - Network Types - Protocol Layering - TCP/IP Protocol suite - OSI
Model - Introduction to Sockets - Application Layer protocols: HTTP - FTP - Email protocols (SMTP
- POP3 - IMAP - MIME) - DNS - SNMP
PART-A CO Knowledge
Stmt Level(R/U/Ap
/An/E/C)
1 Compare LAN and WAN. BTL
LAN WAN 2
CO1
Scope of Local Area Network Scope of Wide Area Network
is restricted to a small/ single spans over large geographical area
building country/ Continent
LAN is owned by some A part of network asserts is owned
organization. or not owned.
Data rate of LAN 10-.10- Data rate of WAN is Gigabyte.
100mbps.

2 Define Full Duplex and simplex transmission system. CO1 BTL1

With Full duplex transmission, two stations can simultaneously
send and receive data from each other. This mode is known as
two-way simultaneous. The signals are transmitted in only one
direction. One is the sender and another is the receiver.
3 Define networks. (Nov 12) CO1 BTL1
A computer network is a group of computer systems and other
computing hardware devices that are linked together through
communication channels to facilitate communication and resource-
sharing among a wide range of users. Networks are
commonly categorized based on their characteristics.
4 Why do we need a Domain Name System? What role does the CO1 BL2
DNS Resolver play in the DNS system? (Nov 12)
Domain Name System can map a name to an address and
conversely an address to name. The Domain Name System
converts domain names into IP numbers. IP numbers uniquely
identify hosts on the Internet
5 What are the four fundamental characteristics that the data CO1 BTL2
communication system depends on?
The four fundamental characteristics are: Delivery, Accuracy,
Timeliness and Jitter.
6 What are the five components of data communications system? CO1 BTL2
The five components are Message, Sender, Receiver,
Transmission Medium and Protocol.

Adhiparasakthi engineering college

 CS3591-Computer Networks Department of CSE 2022-2023
7 Define link and state the types of connection. CO1 BTL1
A link is the communication pathway that transfers data from
one device to another. The two possible types of connections are
point to point and multipoint
8 Define point to point and Multipoint. CO1 BTL1
Point to point: A point to point connection provides a dedicated
link between two devices.
Multipoint: A multipoint connection is one in which more than
two specific devices share a single link.
9 What is Network topology? List its types. CO1 BTL1
Network topology is the interconnected pattern of network
elements. A network topology may be physical, mapping
hardware configuration, or logical, mapping the path that the
data must take in order to travel around the network. The types are
Bus topology, Star topology, Mesh topology and Ring Topology.
10 What are the four main properties of HTTP? CO1 BTl1
 Global Uniform Resource Identifier.
 Request-response exchange.
 Statelessness.
 Resource metadata.
11 What is a protocol? What are the key elements of a protocol? (Nov CO1 BTL1
15)
Protocol is the set of rules governing the exchange of data between
two entities. It defines what is communicated, how it is
communicated, when it is communicated. The Key elements of a
Protocol are as follows,
 Syntax – It refers to the structure or format of data meaning the
order in which they are presented.
 Semantics – It refers to the meaning of each section of bit. How
to do interpretation.
 Timing – When data should be sent and how fast they can be
sent.
12 Define File Transfer Protocol. (Nov 21) CO1 BTL1
The File Transfer Protocol is a standard communication protocol
used for the transfer of computer files from a server to a client
on a computer network. FTP is built on a client–server model
architecture using separate control and data connections
between
the client and the server.
13 What is WWW and SMTP? (Nov 10,15 ) (May 15) CO1 BTL2
World Wide Web is an internet application that allows user to view
pages and move from one web page to another.

Adhiparasakthi engineering college

 CS3591-Computer Networks Department of CSE 2022-2023
It helps to store and share data across varied distances. The
TCP/IP protocol that supports electronic mail on the Internet is
called Simple Mail Transfer (SMTP). It is a system for sending
messages to other computer users based on e-mail addresses.
14 List the two types of DNS message. (May 16) CO1 BTL1
There are two types of DNS messages – Query and Response
 Query message – consists of the header and question records.
 Response message – consists of header, question record,
authoritative record and additional record.
15 What is a layered Network Architecture? CO1 BTL1
A layer is created when a different level of abstraction occurs at
protocol. Each layer should perform a well-defined function.
Function of each layer should be chosen using internationality
standardized protocols. Boundaries between should be chosen to
minimize information flow across the interfaces.
16 Compare OSI and TCP/IP models. CO1 BTL
OSI Model TCP / IP Model 2
It distinguishes between It does not distinguish between
Service, Interface, Protocol Service, Interface, Protocol
Protocols are well hidden Protocols are not just hidden
Dejure standard Fit Model Defacto standard Fit Model
In transport layer only In Transport layer choice is for
connection-oriented services connection oriented and
are available connectionless
Contains 7 layers Contains 5 layers
17 How do layers of the internet model correlate to the layers of CO1 BTL
the 2
OSI model?
OSI TCP/IP
Physical Layer Physical Layer
Data Link Layer Network Access Layer
Network Layer IP Layer
Transport Layer TCP Layer
Session Layer
Presentation Layer Application Layer
Application layer
18 Describe why HTTP is defined as a stateless protocol. CO1 BTL2
Maintaining state across request – Response connections
significantly increases the initial interactions in a connection, since
the identity of each party needs to be established and any saved
state much be retrieved. HTTP is therefore stateless to ensure that

Adhiparasakthi engineering college

 CS3591-Computer Networks Department of CSE 2022-2023
internet is scalable since state is not contained in a HTTP request
/
response pair by default.
19 What are the four groups of HTTP Headers? What are the two CO1 BTL1
methods of HTTP? (May 15) (Nov 15)
The four groups of HTTP headers are
 General headers
 Entity Headers
 Request Headers
 Response Headers.
Two methods of HTTP are Get Method( ) Post Method( )
20 Justify the need for layer five in the OSI model. (Nov 21) CO1 BTL2
Layer 5 of the OSI Model: Session Layer is the layer of the ISO
Open Systems Interconnection (OSI) model that controls the
dialogues (connections) between computers. It establishes,
manages, and terminates the connections between the local and
remote application.
21 What are the functions of Application Layer? (Apr 11) CO1 BTL1
It enables the user (human/software) to access the network. It
provides user interfaces and support for services such as electronic
mail, remote file access and transfer, shared database management
and other types of distributed information services. Services
provided by the application layer are Network Virtual terminal,
File transfer, access and management. Mail services, Directory
services.
22 Define anonymous FTP. (May / June 2021) CO1 BTL1
An anonymous FTP is where users are given access to a
distributed file where they do not need to sign in with a specific
username and password.
23 What are the transmission modes of FTP? CO1 BTL1
Stream mode: Default mode and data is delivered from FTP to
TCP as a continuous stream of data.
Block mode: Data is delivered from FTP to TCP in terms of
blocks. Each data block follows the three-byte header.
Compressed mode: File is compressed before transmitting if size
is big. Run length encoding method is used for compression.
24 Why is an application such as POP needed for electronic CO1 BTL2
messaging? (May 12)
Workstations interact with the SMTP host, which receives the
mail on behalf of every host in the organization, to retrieve
messages by using a client-server protocol such as Post
Office Protocol.
Although POP3 is used to download messages from the server,
Adhiparasakthi engineering college
CS3591-Computer Networks Department of CSE 2022-2023
the

Adhiparasakthi engineering college

 CS3591-Computer Networks Department of CSE 2022-2023
SMTP client still needed on the desktop to forward messages from
the workstation user to its SMTP mail server.
25 What is the difference between IMAP and POP? (May / June CO1 BTL2
2021)
POP IMAP
POP allows downloading IMAP allows the user to see
messages from your Inbox to all the folders on the mail
your local computer server.
The mail can only be accessed Messages can be accessed
from a single device at a time. across multiple devices
To read the mail it has to be The mail content can be read
downloaded on the local partially before downloading.
system
The user cannot organize mails The user can organize the
in the mailbox of the mail emails directly on the mail
server. server.
26 What is the use of MIME Extension? CO1 BTL2
Multipurpose Internet Mail Extensions (MIME) is a
supplementary protocol that allows non-ASCII data to be sent
through SMTP. MIME transforms non-ASCII data at the sender
site to NVT ASCII data and deliverers it to the client SMTP to be
sent through the Internet. MIME converts binary files, executed
files into text files. Then only it can be transmitted using SMTP
27 How are the subgroups of the OSI model layers segregated by CO1 BTL1
their functions? (May / June 2021)
The lower 4 layers (transport, network, data link and physical)
are concerned with the flow of data from end to end through the
network and hence are called as network support layers. The
upper four layers of the OSI model (application, presentation and
session) are orientated more toward services to the applications
and hence are called user support layers.
28 Identify the Port number of Hyper Text Transfer Protocol and CO1 BTL1
Telnet. (Nov 21)
By default, these two protocols are on their standard port number
of 80 for HTTP and 443 for HTTPS. For telnet port number is 23.
29 Discuss the three main division of the domain name space. CO1 BL1
(May
12)
Domain name space is divided into three different sections:
generic domains, country domains & inverse domain.
 Generic domain: Define registered hosts according to their
generic behavior, uses generic suffixes.

Adhiparasakthi engineering college

 CS3591-Computer Networks Department of CSE 2022-2023
 Country domain: Uses two characters to identify a country as
the last suffix.
Inverse domain: Finds the domain name given the IP address.
30 Define SNMP. (May 12) CO1 BTL1
Simple Network Management Protocol (SNMP) is an "Internet-
standard protocol for managing devices on IP networks". Devices
that typically support SNMP include routers, switches, servers,
workstations, printers, & modem. It is used mostly in network
management systems to monitor network-attached devices for
conditions that warrant administrative attention.
31 List the two types of DNS message. (May 16) CO1 BTL1
There are two types of DNS messages,
 Query
 Response
Query message – consists of the header and question records.
Response message – consists of header, question record,
authoritative record and additional record.
PART-B
1 Explain different types of networks in detail with neat diagram CO1 BTL1
(Nov/Dec 2021)
3 Discuss in detail about the layers in OSI model. (Nov CO1 BTL2
10,11,12,15,19) (May 12) (May / June 2021)
4 Explain in detail about the TCP/IP protocol suite with neat CO1 BTL1
diagram
5 Discuss how the Simple Mail Transfer Protocol (SMTP) is useful in CO1 BTL2
electronic mail. (May 12,15) (Nov 13,15) (Nov 19) (May/June 2021)
(Nov 21)
6 Explain the role of a DNS on a computer network, including its CO1 BTL1
involvement in the process of a user accessing a web page. (May
13) (Nov 15, 19) (Nov 21)
7 Explain about HTTP. Give their uses, state strengths and CO1 BTL1
weaknesses. (Nov 10,13)
8 Explain about FTP. (Nov 12, 13, 19), May 13) CO1 BTL1

9 Explain in detail about SNMP. CO1 BTL1

10 Explain in detail about sockets with an example. CO1 BTL1

UNIT II TRANSPORT LAYER
Introduction - Transport-Layer Protocols: UDP - TCP: Connection Management - Flow control -
Congestion Control - Congestion avoidance (DECbit, RED) - SCTP - Quality of Service
PART-A CO Knowledge
Stateme Level(R/U/Ap

Adhiparasakthi engineering college

 CS3591-Computer Networks Department of CSE 2022-2023
nt /An/E/C)
1 Give any two Transport layer service. (Dec 12) CO2 BTL
Multiplexing: Transport layer performs multiplexing/de- 1

multiplexing function. Multiple applications employ same

transport protocol, but use different port number. According to
lower layer n/w protocol, it does upward multiplexing or
downward multiplexing.
Reliability: Error Control and Flow Control.
2 How IANA has divided port numbers? CO2 BTL
IANA (Internet Assigned Number Authority) has divided port 2
numbers into three ranges: 1) Well Known ports
2) Registered ports 3) Dynamic Ports.
3 List few well known ports for UDP. CO2 BTL1
Port Protocol Description
7 Echo Echoes a received datagram back to the sender
9 Discard Discards any datagram received
11 Users Active Users
13 Daytime Returns Date and Time
4 How congestion occurs in a network? (May / June 2021) CO2 BTL
The routers / switches in a network have a limited buffer size to 2
store the received packets. If the packets arrive at a faster rate than
what the receiver can store, then the packets are dropped leading
to congestion.
5 What is a Port? (Nov 21) CO2 BTL
In computer networking, a port is a communication endpoint. At 1
the software level, within an operating system, a port is a logical
construct that identifies a specific process or a type of network
service.
6 Give the datagram format of UDP? CO2 BTL
The basic idea of UDP is for a source process to send a message to 1
a port and for the destination process to receive the message from
a port.
Source Port Destination Port
Address Address
16 bits 16 bits
Total Length Checksum
16 bits 16 bits

Adhiparasakthi engineering college

 CS3591-Computer Networks Department of CSE 2022-2023
7 CO2 BTL2
What is the main difference between TCP & UDP?
TCP UDP
It provides connection- Provides connectionless service.
oriented service
Connection Establishment No connection establishment
delay will be there and no delay
Provides reliable service Provides unreliable, but fast
service
It is used by FTP, SMTP It is used by DNS, SNMP, audio,
video and multimedia
applications.
8 Name the techniques and policies that can prevent (avoid) CO2 BTL1
congestion.
Techniques to avoid congestion:
 DEC (Digital Equipment Corporation) bit.
 Random Early Detection (RED).
 Source based congestion avoidance.
The congestion may be avoided by two policies:
 BECN - Backward Explicit Congestion Notification
 FECN - Forward Explicit Congestion Notification.
9 List out various congestion control techniques. CO2 BTL1
AIMD (Additive Increase Multiplicative Decrease), Slow start,
Fast retransmit, Fast Recovery
10 What are the advantages of using UDP over TCP? (Nov 10) CO2 BTL1
UDP is very useful for audio or video delivery which does not
need acknowledgement. It is useful in the transmission of
multimedia
data. Connection Establishment delay will occur in TCP.
11 What is the use of UDP’s Pseudo header? CO2 BTL1
The pseudo header consists of three field from the IP header
protocol number, source IP address and destination IP address
plus the UDP length field (which is included twice in checksum
calculation). The pseudo header is used to check whether the
message is delivered between 2 endpoints.
12 What are the four aspects related to the reliable delivery of CO2 BTL1
data?
(May 12)
The four aspects are
(i) Error control,
(ii) Sequence control
(iii) Loss control

Adhiparasakthi engineering college

CS3591-Computer Networks Department of CSE 2022-2023

(iv) Duplication control.

Adhiparasakthi engineering college

 CS3591-Computer Networks Department of CSE 2022-2023
13 Outline Stop and Wait ARQ mechanism. (Nov 19) CO2 BL1
In the stop-and-wait ARQ mechanism, sender sends one frame at
a time; it is a special case of the general sliding
window protocol with transmit and receive window sizes equal
to
one in both cases.
14 What do you mean by slow start in TCP congestion? (May 16) CO2 BTL1
TCP slow start is an algorithm which balances the speed of a
network connection. Slow start gradually increases the amount
of data transmitted until it finds the network’s maximum
carrying
capacity.
15 CO2 BTL2
Differentiate congestion control and flow control. (Nov 13,15)
Congestion Control Flow Control
Congestion control means Flow control means preventing the
preventing the source source from sending data that the
from sending data that receiver will end up dropping
will end up getting because it runs out of buffer space.
dropped by a router
because its queue is full.
This is more complicated, This is fairly easy with a sliding
because packets from window protocol
different sources
travelling different paths
can converge on the same
queue.
16 List the different phases used in TCP Connection. (May 16) CO2 BTL1
The different phases used in TCP connection are Connectio
establishment Phase, Data transfer and Connection Terminatio
Phase
17 List the advantages of Connection oriented services over CO2 BTL1
connectionless services. (May 17)
Connection Oriented:
Advantages:
1. Buffers can be reserved in advance
2. Sequencing can be
guaranteed. Short headers.

Adhiparasakthi engineering college

 CS3591-Computer Networks Department of CSE 2022-2023
18 How do fast retransmit mechanism of TCP works? (May 17) CO2 BTL2
Fast Retransmit is an enhancement to TCP that reduces the time
sender waits before retransmitting a lost segment. A TCP sende
uses a timer to recognize lost segments. If an acknowledgement i
not received for a particular segment within a specified time (

Adhiparasakthi engineering college

 CS3591-Computer Networks Department of CSE 2022-2023
function of the estimated round-trip delay time), the sender wil
assume the segment was lost in the network, and will retransmit th
segment.
19 Define SCTP (Nov 21) CO2 BTL1
SCTP (Stream Control Transmission Protocol) is a reliable, message-
oriented transport layer protocol. It combines the best features of
UDP and TCP. It is mostly designed for internet
applications.
20 What is the use of SCTP Multiple stream service? CO2 BTL2
SCTP allows multi stream service in each connection, which is
called association in SCTP terminology. If one of the streams is
blocked, the other streams can still deliver their data. The idea is
similar to multiple lanes on a highway. The figure shows the idea
of multi stream delivery.
21 Define Multihoming Concept of SCTP CO2 BTL1
Multihoming is the ability of an SCTP association to support
multiple IP paths to its peer endpoint. The benefit
of multihoming associations is that it makes the association more
fault-tolerant against physical network failures and other issues on
the interfaces.

22 What happens in a three-way handshaking between any 2 CO2 BTL2

devices? (May/June 2021)
The three-way handshake involves the exchange of three messages
between the client and the server.
The client sends a segment to the server stating the initial sequence
number it plans to use (Flags = SYN, Sequence Num = x).
The server responds with a single segment that both acknowledges
the client’s sequence number (Flags = ACK, ACK = x +1) and
states its own beginning sequence number, (Flags = SYN,
Sequence Num
= y).
Both the SYN and ACK bits are set in the Flags field of this second
message.
23 What are the two categories of QoS attributes? CO2 BTL1
User Oriented and Network Oriented. User related attributes are

Adhiparasakthi engineering college

CS3591-Computer Networks Department of CSE 2022-2023

Adhiparasakthi engineering college

 CS3591-Computer Networks Department of CSE 2022-2023
SCR – Sustainable Cell Rate
PCR – Peak Cell Rate
MCR- Minimum Cell Rate
CVDT – Cell Variation Delay Tolerance.
The network related attributes are, Cell loss ratio (CLR), Cell
transfer delay (CTD), Cell delay variation (CDV), Cell error ratio
(CER).
UNIT-II / PART-B
1 Write short notes on (May 12) (Nov 19) (Nov 21) CO2 BTL1
(i) TCP segment format (ii) Silly window syndrome (Or) discuss
the silly window syndrome and explain how to avoid it.
2 With neat architecture, Explain TCP and its sliding window CO2 BTL2
algorithm for flow control. (Nov 15)
3 Describe with examples the three mechanisms by which CO2 BTL2
congestion control is achieved in TCP. (Nov 13,15)(May 15,16)(Nov
19)
4 Discuss congestion avoidance algorithm like DEC bit method and CO2 BTL2
random early detection in transport layer with an example.(May
12,17)
5 What are the 2 broad categories of congestion control mechanisms? CO2 BTL1
Briefly explain all the techniques. (May / June 2021)
6 Explain connection establishment and connection closing in TCP CO2 BTL2
(Or) Describe how reliable and ordered delivery is achieved
through TCP. (Nov 13) (May 15)
7 Explain the significance of Clark’s solution and Nagle’s algorithm. CO2 BTL4
(Or) What is the need for Nagle’s algorithm? How does it
determine when to transmit data? (May 13)
8 Define UDP. Discuss the operations of UDP. Explain UDP CO2 BTL2
checksum with one example. (Nov 21)
9 Discuss the effectiveness of Go Back N and Selective Repeat ARQ CO2 BTL2
among the Sliding window Protocols. (Nov 21)
10 Explain SCTP in Detail (May 17) CO2 BTL2
11 Explain the association establishment of SCTP through four-way CO2 BTL2
handshake in detail.
12 Furnish the packet format of Stream Control Transmission CO2 BTL1
Protocol with its fields. How the data are transferred using 4-way
handshaking? (May / June 2021)
13 Explain the various approaches to improve quality of services in a CO2 BTL2
data transmission network.
\

Adhiparasakthi engineering college

 CS3591-Computer Networks Department of CSE 2022-2023
UNIT III NETWORK LAYER
Switching: Packet Switching - Internet protocol - IPV4 - IP Addressing - Subnetting - IPV6, ARP, RARP,
ICMP, DHCP
UNIT-III / PART-A CO Knowledge
Stateme Level (R/U/Ap
/An/E/C)
nt
1 What is packet switching? (Nov 12) CO3 BTL1
In a packet-switched network, it’s not necessary to dedicate
transmission capacity along a path through the network. Rather,
data are sent out in a sequence of small chunks, called packets.
2 What is subnetting? (Nov 11,15) CO3 BTL1
The whole network can’t manage by single server, so that the entire
network divided into small network in order to manage the
network easily. Subnetting provides an elegantly simple way to
reduce the total number of network numbers that are assigned. The
idea is to take a single IP network number and allocate the IP
address with that network to several physical networks, which are
now referred to as subnets.
3 What is subnet mask? CO3 BTL1
A subnet mask is a number that defines a range of IP
addresses available within a network. A single subnet mask
limits the number of valid IPs for a specific network. Multiple
subnet masks can organize a single network into smaller
networks (called
subnetworks or subnets).
4 Define CIDR? CO3 BTL1
CIDR, which stands for Classless Inter-Domain Routing, is an IP
addressing scheme that improves the allocation of IP addresses.
It replaces the old system based on classes A, B, and C. This
helped to extend the life of IPv4 as well as slow the growth of
routing
tables.
5 How many network addresses and host addresses are CO3 BTL1
supported by class A, class B networks?
Class A: Number of networks = 127 Number of hosts = 224 -1
Class B: Number of networks = 214 -1
Number of hosts = 216 – 1 = 65,535

Adhiparasakthi engineering college

 CS3591-Computer Networks Department of CSE 2022-2023
6 List out the functions of IP. CO3 BTL1
IP services are unreliable, best-effort, connectionless packet
delivery system. Unreliable – delivery is not guaranteed,
Connectionless – each pocket is treated independent from others,

Adhiparasakthi engineering college

 CS3591-Computer Networks Department of CSE 2022-2023
Best-effort delivery – it makes an earnest attempt to deliver
packets. It defines basic unit of data transfer through TCP/IP.
7 What do you mean by ICMP? CO3 BTL1
ICMP is an error reporting mechanism. It does not specify the
action to be taken for each possible error. The source must relate
the error to an individual application program and take other
actions to correct the problem.
8 To whom ICMP reports error message will be sent? CO3 BTL2
ICMP allows routers to send error messages to other router or
hosts. ICMP is an error reporting mechanism. It does not specify
the action to be taken for each possible error. It is informing the
source that the error has occurred and the source has to take
actions to rectify the errors.
9 When ICMP redirect message is used? (May 17) CO3 BTL2
An ICMP redirect is an error message sent by a router to the
sender of an IP packet Redirects are used when a router believes a
packet is being routed sub optimally and it would like to inform
the sending host that it should forward the subsequent packets to
that same destination through a different gateway.
10 State the rules of non-boundary-level masking? (May 12) CO3 BL3
 The bytes in the IP address that corresponds to 255 in the mask
will be repeated in the sub network address.
 The bytes in the IP address that corresponds to 0 in the mask
will change to 0 in the sub network address.
 For other bytes, use the bit-wise AND
operator. Example-
IP address 45 123 21 8
Mask 255 192 0 0
Subnet 45 64 0 0
123 01111011
192 11000000
64 01000000
11 How many network addresses and host addresses are CO3 BTL2
supported by class A, class B networks?
Class A: Number of networks = 127 Number of hosts = 224 -1
Class B: Number of networks = 214 -1
Number of hosts = 216 – 1 = 65,535

Adhiparasakthi engineering college

 CS3591-Computer Networks Department of CSE 2022-2023
12 What is the network address in a class A subnet with the IP CO3 BTL2
addresses of one of the hosts as 25.34.12.56 and mask
255.255.0.0? (May 14)
IP Address - 25.34.12.56 , Mask - 255.255.0.0 , Network Address
- 25.34.0.0
13 What is IP address? CO3 BTL1
An Internet Address is made of four bytes (32 bits) that define a
host’s connection to a network. There are currently 5 different field
lengths patterns, each define a class of addresses. These are
designed to cover the needs of different types of organizations,
class A, B, C, D, E.
14 Explain IPV6 protocol. Why IPV6 is preferred over IPV4? (May CO3 BTL2
/ June 2021)
IPv6 (Internet Protocol version 6) is a set of basics of IPv6 are
similar to those of IPv4. The most obvious improvement in IPv6
over IPv4 is that IP addresses are lengthened from 32 bits to 128
bits. This extension anticipates considerable future growth of the
Internet and provides relief for what was perceived as an
impending shortage of network addresses.
15 What is DHCP? (Nov 19) CO3 BTL1
DHCP (Dynamic Host Configuration Protocol) is a protocol that
provides quick, automatic, and central management for the
distribution of IP addresses within a network. DHCP is
also used to configure the subnet mask, default gateway, and
DNS server information on the device.
16 Explain IPV4 protocol. CO3 BTL2
IPv4 (Internet Protocol Version 4) is the fourth revision of the
Internet Protocol (IP) used to identify devices on a
network through an addressing system. The Internet Protocol is
designed for use in interconnected systems of packet-switched
computer communication networks. IPv4 is the most widely
deployed Internet protocol used to connect devices to the Internet.
IPv4 uses a 32-bitaddress scheme
17 Present an outline of IPv6 addressing. (Nov 19) CO3 BTL2
An IPv6 address is 128 bits in length and consists of eight, 16-bit
fields, with each field bounded by a colon. Each field must
contain a hexadecimal number, in contrast to the dotted-decimal
notation

Adhiparasakthi engineering college

 CS3591-Computer Networks Department of CSE 2022-2023
of IPv4 addresses. In the below figure, the x's represent
hexadecimal numbers.
18 CO3 BTL1
What are the differences between IPV4 and IPV6? (Nov 21)
IPV4 IPV6
A 32-bit numeric address in IPv6 addresses are 128-bit IP
IPv4 is written in decimal as address written in hexadecimal
four numbers separated by and separated by colons. An
periods. Each number can be example IPv6 address could be
zero to 255. written like this:
For eg, 3ffe:1900:4545:3:200:f8ff:fe21:67
1.160.10.240 could be an IP cf
address.
19 Identify the class of the following IP Address: (May / June 2021) CO3 BTL2
11000001 10000011 00011011 11111111 = Class C
252.5.15.111 = Class D
20 Why is IPV4 to IPV6 transition required? (May 17) CO3 BTL2
IPv4 and IPv6 networks are not directly interoperable, transition
technologies are designed to permit hosts on either network type
to communicate with any other host.
21 CO3 BTL2
Compare ARP and RARP.
ARP RARP
Address Resolution Protocol. Reverse Address Resolution
Protocol.
Retrieves the physical address Retrieves the logical address for
of the receiver. a computer from the server.
22 What is the need of ARP? (Nov/Dec 2015) CO3 BTL2
ARP is used to find the physical address of the node when its
Internet address is known. Any time a host/router needs to find
the physical address of another host on its network, it formats an
ARP query packet that includes the IP address and broadcasts it.
All hosts in the network process the ARP packet but only the
required station sends back physical address.
23 Define RARP. CO3 BTL1
Allows a host to discover its internet address when it knows only
its physical address (a diskless computer). The host wishing to
retrieve its internet address broadcasts an RARP query packet that
contains its physical address to every host on its physical network.

Adhiparasakthi engineering college

 CS3591-Computer Networks Department of CSE 2022-2023
A server on the network recognizes the RARP packet and returns
the host’s internet address.
24 How many network addresses and host addresses are supported CO3 BTL1
by class A, class B networks?
 Class A: Number of networks = 127
Number of hosts = 224 -1
 Class B: Number of networks = 214 -1
Number of hosts = 216 – 1 = 65,535
25 List the difference between Packet Switching and Circuit CO3 BTL
Switching. (Apr/May 2011, Nov/Dec 2011, May/June 2014) 1

Issue Packet switching Circuit Switching

Circuit setup Not Required Required
Transmission No Transmission path Dedicated path
path
Delay Packet transmission Call setup delay
delay
Addressing Each packet contains Only data is sent
the full source and
destination address
Bandwidth Dynamic Bandwidth Fixed Bandwidth
Routing Each packet is routed Entire data is sent
independently through the same path
Congestion Difficult Easy if enough buffers
control can be located in
advance for each VC set
up
Complexity In the transport layer In the network layer
Suited for Connection-oriented Connection-oriented
and connectionless service
service
UNIT-III / PART-B
1 Explain Packet Switching in detail. CO3 BTL2
2 i) Discuss the IP addressing methods. (May/June2014) CO3 BTL2
ii) Write short notes on ARP. (May/June2014) or Explain in detail
ARP. (Nov/Dec 2015)
3 Explain in detail about DHCP. (Nov/Dec 2015) CO3 BTL2
4 What is the need for ICMP? Mention ICMP MESSAGES and their CO3 BTL1
purpose. (May/June 2013)
5 Explain about IPV6? Compare IPV4 and IPV6 (May 16)(Nov 21) CO3 BTL2

Adhiparasakthi engineering college

 CS3591-Computer Networks Department of CSE 2022-2023
6 Discuss about address Resolution protocols. (Nov/Dec 2013) CO3 BTL2
7 Explain in detail about: i) ICMP ii) ARP iii) RARP. (Nov 19) CO3 BTL2
8 Explain IPv4 packet format and how fragmentation is applied in CO3 BTL3
datagram delivery.
9 Draw an IPv4 datagram and explain about the fields present in it. CO3 BTL2
UNIT IV ROUTING
Routing and protocols: Unicast routing - Distance Vector Routing - RIP - Link State Routing - OSPF
- Path-vector routing - BGP - Multicast Routing: DVMRP - PIM.
UNIT IV - PART A CO Knowledge
Stateme Level(R/U/Ap
nt /An/E/C)
1 Define routing. (Nov12,15) CO4 BTL1
It is the process of building up the tables that allow the collect
output for a packet to be determined. It is a lot harder to create the
forwarding tables in large, complex networks with dynamically
changing topologies and multiple paths between destinations.
Routing is a process that takes place in the background so that,
when a data packet turns up, we will have the right information
in the forwarding table to be able to forward, or switch, the packet.
2 Write on the packet cost referred in distance vector and link state CO4 BTL1
routing. (May 2012)
In distance vector routing, cost refer to hop count while in case
of link state routing, cost is a weighted value based on a variety
of
factors such as security levels, traffic or the state of the link.
3 What is source routing? (Nov 13) CO4 BTL1
Rotation, stripping off and using pointers are the different types
of source routing approach.
4 What is the function of a router? (Nov 10)(Nov 21) CO4 BTL1
Routers relay packets among multiple interconnected networks.
They route packets from one network to any of a number of
potential destination networks on internet. A router operates at
the physical, data link and network layer of the OSI model.
5 Write the difference between Distance vector routing and Link CO4 BTL2
state routing.
Distance Vector Routing Link state routing
Basic idea is each node sends Basic idea is every node sends
its knowledge about the entire its knowledge about its
network to its neighbors. neighbors to the entire
network
It is dynamic routing It is dynamic routing
RIP uses Distance vector OSPF uses link state routing
routing

Adhiparasakthi engineering college

 CS3591-Computer Networks Department of CSE 2022-2023
6 What does a router do when it receives a packet with a CO4 BTL1
destination address that it does not have an entry for, in its
routing table?
Default Router: If IP Software is not able to find the destination, from
routing table then it sends the datagram to default router. It is useful
when a site has small set of local address connected to it and
connected
to the rest of the Internet.
7 What is piggybacking? (Nov 19) CO4 BTL1
The technique of temporarily delaying outgoing
acknowledgment so that they can be hooked onto the next
outgoing data frame is
widely known as piggybacking.
8 Explain Multicast routing? CO4 BTL2
Multicast IP Routing protocols are used to distribute data for
example, audio/video streaming broadcasts) to multiple
recipients. Using multicast, a source can send a single copy of
data to a single multicast address, which is then distributed to an
entire
group of recipients.
9 What is RIP? CO4 BTL1
RIP (Routing Information Protocol) is a widely-used protocol for
managing router information within a self-contained network
such as a corporate local area network or an interconnected group
of such LANs. Using RIP, a gateway host (with a router) sends its
entire routing table (which lists all the other hosts it knows about)
to its closest neighbor host every 30 seconds.
10 Explain about OSPF. CO4 BTL2
OSPF (Open Shortest Path First) is a router protocol used within
larger autonomous system networks in preference to the
Routing Information Protocol (RIP), an older routing protocol
that is
installed in many of today's corporate networks.
11 What is PIM? CO4 BTL1
Protocol-Independent Multicast (PIM) is a family
of multicast routing protocols for Internet Protocol (IP) networks
that provide one-to-many and many-to-many distribution of data
over a LAN, WAN or the Internet. It is termed protocol-
independent because PIM does not include its own topology
discovery mechanism, but instead uses routing information
supplied by other routing protocols.
PIM Source-Specific Multicast, Bidirectional PIM
PIM Dense Mode, PIM Sparse Mode

Adhiparasakthi engineering college

 CS3591-Computer Networks Department of CSE 2022-2023
12 What is DVMRP? CO4 BTL1
The Distance Vector Multicast Routing Protocol (DVMRP), is
a routing protocol used to share information between routers to
facilitate the transportation of IP multicast packets among
networks. The protocol is based on the RIP protocol. The router

Adhiparasakthi engineering college

 CS3591-Computer Networks Department of CSE 2022-2023
generates a routing table with the multicast group of which it has
knowledge with corresponding distances. When a multicast
packet is received by a router, it is forwarded by the router's
interfaces specified in the routing table.
13 What are the metrics used by routing protocols? (Apr/May 2015) CO4 BTL1
Path length, bandwidth, load, hop count, path cost, delay,
Maximum Transmission Unit (MTU), reliability and
communications cost.
14 Define Unicasting, Broadcasting and Multicasting. (Nov/Dec CO4 BTL1
2011)
Unicasting: Transmitting data from a single sender to a single
receiver.
Broadcasting: Transmitting data from a single source to all the
other nodes in the network
Multicasting: Transmitting data from a single source to a group
of destination nodes.
15 Explain BGP. CO4 BTL2
BGP stands for Border Gateway Protocol. It can be defined as a
standardized exterior gateway protocol which is developed to
interchange routing information and reachability information
between various autonomous systems (AS) on the Internet. It is
classified as a path vector protocol as well as a distance-vector
routing protocol.
16 What is a path vector routing protocol? CO4 BTL1
A path-vector routing protocol is a network routing protocol
which maintains the path information that gets updated
dynamically. Updates that have looped through the network and
returned to the same node are easily detected and discarded.
17 What is count to infinity problem in distance vector routing? CO4 BTL2
1. One of the important issues in Distance Vector Routing is
County of Infinity Problem.
2. Counting to infinity is just another name for a routing loop.
3. In distance vector routing, routing loops usually occur when
an interface goes down.
4. It can also occur when two routers send updates to each other
at the same time.
18 What techniques are used to overcome the count to infinity CO4 BTL1
issue in distance vector routing?
Split horizon technique and split horizon with poison reverse
technique are used to overcome count to infinity issue in distance
vector routing.
19 What are the contents of a link spate packet (LSP)? CO4 BTL1
LSP contains the following information:
1. The ID of the node that created the LSP
2. A list of directly connected neighbors of that node, with the

Adhiparasakthi engineering college

 CS3591-Computer Networks Department of CSE 2022-2023
cost of the link to each one
3. A sequence number
4. A time to live for this packet

20 What is the main difference between BGP and Distance vector CO4 R
routing.
BGP differs from Distance Vector and Link State routings as it
advertises complete paths as an enumerated list of ASs to reach a
particular network.
UNIT IV - PART B
1 Explain what is Distance Vector Routing and Demonstrate how CO4 BTL2
distance table gives routing table (Nov 21)
2 Discuss about Link-state routing and routers. (Nov 12) (May 15) CO4 BTL2
3 Explain about the inter domain routing (BGP) routing algorithms. CO4 BTL2
4 Explain the Routing Information protocol/Distance vector C04 BTL2
routing in detail. (Nov 13,15) (May 15,16)(Nov 19)
5 What are the different routing algorithms? List out their pros and CO4 BTL1
cons. (May / June 2021)
6 Explain Link state routing with Dijkstra's algorithm for CO4 BTL3
the following graph.

7 Explain Distance Vector Routing Algorithm for the graph given CO4 BTL3
below.

8 Explain in detail the operation of OSPF protocol by considering a CO4 BTL3

suitable network. (May 17)
9 Explain DVMRP multicast routing in detail CO4 BTL2
10 Explain PIM multicast routing in detail. C04 BTL2
UNIT V DATA LINK AND PHYSICAL LAYERS
Data Link Layer - Framing - Flow control - Error control - Data-Link Layer Protocols - HDLC - PPP -
Media Access Control - Ethernet Basics - CSMA/CD - Virtual LAN - Wireless LAN (802.11)
- Physical Layer: Data and Signals - Performance - Transmission media- Switching - Circuit Switching.
UNIT V - PART A CO Knowledge
Stateme Level(R/U/Ap
nt /An/E/C)
1 List out the functions of data link layer (May / June 2021) C05 BTL1

Adhiparasakthi engineering college

 CS3591-Computer Networks Department of CSE 2022-2023
Data link layer deals with node-to-node delivery of data. The
services provided by the data link layer include: framing, flow
control, error control and access control.
2 What do you mean by framing? (Nov/Dec2013 and Nov/Dec CO5 BTL1
2014)
The data link layer divides the stream of bits received from the
network layer into manageable data units called frames. The
ways to address the framing problem are
 Byte-Oriented Protocols (PPP)
 Bit-Oriented Protocols (HDLC)
 Clock-Based Framing (SONET)
3 What are the two types of errors occurred during data CO5 BTL1
transmission? (May/June 2012)
Single bit error and burst error
4 Compare error detection and correction. (Nov/Dec 2012) CO5 BTL2
Error Detection Error Correction
Only the occurrence of an error The exact number of bits that
is checked are corrupted and location of
error in the message are known.
5 Define bit stuffing. (Apr/May 2011) CO5 BTL1
HDLC denotes both the beginning and the end of a frame with
the distinguished bit sequence 01111110. This sequence might
appear anywhere in the body of the frame, it can be avoided by
bit stuffing. On the sending side, any time five consecutive 1’s has
been transmitted from the body of the message (i.e., excluding
when the sender is trying to transmit the distinguished
01111110
sequence), the sender inserts a 0 before transmitting the next bit.
6 What do you mean by Flow Control? (Nov/Dec 2011) CO5 BTL1
Flow control is a technique for assuring that a transmitting entity
does not overwhelm a receiving entity with data. It is a feedback
mechanism by which the receiver is able to regulate the sender.
Such a mechanism is used to keep the sender from overrunning
the receiver, i.e., from transmitting more data than the receiver is
able to process
7 Why is flow control and error control duplicated in different CO5 BTL2
layers?
Like the data link layer, the transport layer is responsible for flow
and error control. Flow control and error control at data link

Adhiparasakthi engineering college

CS3591-Computer Networks Department of CSE 2022-2023

layer

Adhiparasakthi engineering college

 CS3591-Computer Networks Department of CSE 2022-2023
is node-to-node level. But at transport layer, flow control and error
control is performed end-end rather than across a single link.
8 Differentiate between lost frame and damaged frame? CO5 BTL
Lost Frame Damaged Frame 2
Lost frame is the frame that The damaged frame is a
fails to arrive at the other side. recognizable frame does arrive,
but some of the bits are in error
9 What is the difference between stop and wait and sliding CO5 BTL
window protocol? (Nov/Dec 2012) 2

Stop and Wait Protocol Sliding Window Protocol

In stop and wait protocol, In sliding window protocol, we can
we can send one frame at send multiple frames at a time.
a time
Shows poor performance As sliding window doesn't waste
than Sliding Window network bandwidth compared with
Protocol, comparatively stop-n-wait, both in normal and in
congested condition, sliding window
show better performance than stop-n-
wait.
10 Why sliding window flow control is considered to be more CO5 BTL
efficient than stop and wait flow control? 1
In sliding window flow control, the transmission link is treated
as a pipeline that may be filled with frames in transit. But with
stop-
and-wait flow control only one frame may be in the pipe at a time.
11 Define Piggybacking? CO5 BTL
The technique of temporarily delaying outgoing 1
acknowledgment so that they can be hooked onto the next
outgoing data frame is
widely known as piggybacking.
12 Find the hamming distance between the two pair of code CO5 BTL
words: A = 01011; B = 11110 (May / June 2021) 3
Hamming distance is the numbers of bits by which two codes
differ. Here hamming distance = 3
13 Define hidden node problem. (May 16) CO5 BTL
In wireless networking, the hidden node problem or hidden 1
terminal problem occurs when a node is visible from a wireless
access point (AP), but not from other nodes communicating with
that AP. This leads to difficulties in media access control sub
layer.
14 What is the access method used by wireless LAN? (May 14) CO5 BTL
Adhiparasakthi engineering college
CS3591-Computer Networks Department of CSE 2022-2023
1

Adhiparasakthi engineering college

 CS3591-Computer Networks Department of CSE 2022-2023
The access method used by wireless LAN is Carrier Sense Multiple
Access with Collision Avoidance (CSMA/CA)
15 What is meant by Exponential back of algorithm? CO5 BTL
After first collision, each station waits either 0 or 1 slot time before 1
trying again. If two stations collide and each one picks same
random number 0/1. After second collision, each one picks 0, 1, 2
or 3 slot at random and waits. If collision occurs again, then next
time the number of slots to wait is chosen at random from 0 to
[23
– 1]. This algorithm is called binary exponential “back off
algorithm”.
16 What is High Level data link control? (Nov 21) CO5 BTL
High-Level Data Link Control is a bit-oriented code-transparent 1
synchronous data link layer protocol developed by the
International Organization for Standardization. The standard for
HDLC is ISO/IEC 13239:2002. HDLC provides both connection-
oriented and connectionless service.
17 Give the format of Ethernet address. CO5 BTL
Preambl Dest Src addr Type Body CRC 1
e addr
64 48 48 16 32
18 Outline the use of cyclic redundancy check. (Nov 19) CO5 BTL
A cyclic redundancy check (CRC) is an error-detecting code 2
commonly used in digital networks and storage devices to detect
accidental changes to raw data.
19 What is CSMA/CD? (Nov 11) CO5 BTL
Carrier Sense Multiple Access with Collision Detection is one of 1
the methods of medium access. It is used to sense whether a
medium is busy before transmission. If the medium is busy, it
refrains from transmitting the data or else proceeds with the
transmission. Also has the ability to check whether a transmission
has collided with another.
20 Examine how Network Interface Card works. (Nov 21) CO5 BTL
A Network Interface Card provides a computer with a dedicated, 2
full-time connection to a network. It implements the physical layer
circuitry necessary for communicating with a data link layer
standard, such as Ethernet or Wi-Fi.
21 List the rules for CSMA/CD. CO5 BTL
1. If the medium is idle, transmit; otherwise go to step 2. 1
2. If the medium is busy, continue to listen until the channel is
idle, and then transmit immediately.

Adhiparasakthi engineering college

 CS3591-Computer Networks Department of CSE 2022-2023
3. If a collision detected during transmission, transmit a brief
jamming signal to all station to indicate collision has occurred and
then cease transmission.
22 Mention some of the physical properties of Ethernet. CO5 BTL1
(May 11)
The Ethernet is a multiple-access network, meaning that a set of
nodes send and receive frames over a shared link. An Ethernet is
like a bus that has multiple stations plugged into it.
23 Write the parameters used to measure network performance. CO5 BTL1
(May 2016)
The parameters used to measure network performance are
Latency, Throughput, Delay and Bandwidth.
24 Outline the need for switching. (Nov 19) CO5 BTL2
Switched communication networks are those in which data
transferred from source to destination is routed between various
intermediate nodes. Switching is the technique by which nodes
control or switch data to transmit it between specific points on a
network. There are three common switching techniques:
Circuit Switching, message switching and packet switching.
25 List the types of Transmission media. (Nov 21) CO5 BTL1
Transmission Media is broadly classified into the following types:
Guided Media: It is also referred to as Wired or Bounded
transmission media. Common types are: (i) Twisted Pair Cable (ii)
Coaxial Cable (iii) Optical Fiber Cable
Unguided Media: Wireless Transmission. Common Types are:
(i) Satellite (ii) Infrared (iii) Broadcast (iv)Wi-Fi
26 Define Bandwidth CO5 BTL1
Bandwidth refers to the number of bits per second that a
channel, a link, or even a network can transmit.
27 What is Throughput? CO5 BTL1
It is a measure of how data can actually be sent through network.
28 What is meant by the contention period of Ethernet? CO5 BTL1
When several stations on an Ethernet have data to send, there
are contention periods during which collisions happen and no
data is successfully transmitted.
29 What does IEEE 10 Base 5 standard signify? CO5 BTL1
 10 represents data rate 10 Mbps.
 5 refers to segment length 5* 100 m that can run without
repeaters
 Base represents Base band communication.

Adhiparasakthi engineering college

 CS3591-Computer Networks Department of CSE 2022-2023
30 What do you mean by CSMA protocol? (Apr/May 2015) CO5 BTL1
Carrier sense multiple access (CSMA) is a media access
control (MAC) protocol in which a node verifies the absence of
other traffic before transmitting on a shared transmission
medium.
Carrier sense means that a transmitter attempts to determine
whether another transmission is in progress before initiating a
transmission. If a carrier is sensed, the node waits for the
transmission in progress to end before initiating its own
transmission. In other words, CSMA is based on the principle
"sense before transmit". Multiple access means that multiple nodes
may send and receive on the medium. Transmissions by one node
are generally received by all other nodes connected to the medium.
UNIT-V / PART-B
1 Given a remainder of 111, a data unit of 10110011 and a divisor of CO5 BTL3
1001, is there an error in the data unit. Justify your answer with
necessary principles. (May 14)
2 Explain the various error detection techniques with example. (Nov CO5 BTL2
10,12), (May 12,16)
3 The message X5 + X4 + X 11001001 is to be transmitted, using CRC CO5 BTL3
error detection algorithm. Assuming the CRC polynomial to be X3
+ X2 + 1, determine the three-bit CRC code that should be
appended to message. (May / June 2021)
4 Discuss in detail about the HDLC protocol (Bit Oriented Protocol). CO5 BTL2
(May 16) (Nov 19)
5 Explain various flow control mechanisms. i) Stop Wait protocol ii) CO5 BTL2
Go Back-N iii) Selective Repeat (Nov 15)
6 Discuss in detail about the PPP protocol (Byte Oriented Protocol). CO5 BTL2
7 Describe the CSMA/CD protocol and comment on its performance CO5 BTL4
for medium access. (May 11,14,17) (Nov 19)
8 Explain the functioning of wireless LAN in detail. (Nov 10,12,15) CO5 BTL2
(May 15)
9 Explain how hidden node and exposed node problem is solved in CO5 BTL2
IEEE 802.11 (Nov 13)
10 Explain Transmission media and its types in detail. (May / June CO5 BTL2
2021)
11 Explain the various performance metrics in detail. CO5 BTL2
12 Explain Circuit Switching in detail. (Nov 19)(Nov/Dec 2021) CO5 BTL2

Adhiparasakthi engineering college