3rd International Conference on Multimedia Technology（ICMT 2013)

Design of a 24 GHz Programmable Frequency

Divider in 65-nm CMOS Process ∗
Huagui Bao1, 2, ZhiqunLi1, 2, +, Qin Li1, Zhigong Wang1
1
Institute of RF- & OE-ICs, Southeast University, Nanjing, 210096;
2
School of Integrated Circuits, Southeast University, Nanjing, 210096;
＋
Corresponding author: [email protected]

Abstract: A 24 GHz programmable frequency divider in 65-nm CMOS process is

presented in this paper. The divide ratio can be varied from 208 to 270 in a step
size of 2.The divider consists of a divide-by-2, an 8/9 dual-modulus prescaler, a
programmable pulse-swallow counter and a buffer. The post simulation results
demonstrate that the divider can operate with the input frequency ranging from 16
GHz to 32 GHz while it draws 7.3 mA from a 1.2 V power supply.
Key words: frequency divider; programmable frequency divider; divide-by-2,
prescaler; pulse-swallow counter;

1. Introduction
Frequency dividers are widely used in many communication systems such as
frequency synthesizer, time-recovery circuits and clock generation circuits. In a
phase-locked loop (PLL), a frequency divider is to divide down the local
oscillation frequency generated by the voltage-controlled oscillator (VCO) to
make a comparison with the reference frequency. The programmability provided
by the frequency divider leads to different locking frequencies of the PLL.
In this paper, a programmable divider for a 24 GHz PLL is presented. Fig. 1
shows the architecture of the PLL, and the proposed programmable divider is
presented in the dashed box. As the input frequency of the proposed
programmable divider is approximately 24~26 GHz, the proposed programmable
divider is started by a divide-by-2 instead of traditionally a DMP to provide a
large frequency division bandwidth and to reduce the burden of the DMP.

∗
Project supported by the National High Technology Research and Development Program
(No.2011AA010202)

© 2013. The authors - Published by Atlantis Press 1854

 This paper is organized as follows. Section 2 discusses the circuit design of
the proposed programmable divider. Layout design and post simulation results are
presented in Section 3 and Section 4 comes to the conclusions.
fref
PFD CP LF VCO

24~26GHz

Buffer

Pulse Counter(/P) fclk N/(N+1)

P=13,14,15,16 N=8
Buffer ÷2
fout

Reset MC
Swallow ÷2
Counter(/S)
S=0~7

S4 S5
I+ I- Q+ Q-
S1 S2 S3

Fig. 1 Block diagram of the PLL and the proposed programmable divider

2. Circuit design
As shown in Fig. 1, for the 8/9 DMP, it divides by 8 when modulus controller
(MC) is set to be ‘0’ and 9 when MC is ‘1’. Then, the counter value of the pulse
counter and swallow counter are set to be P and S, respectively. Before swallow
counter counts to 0, MC is high so that the DMP divides by (N+1) which is 9 in
this paper. When swallow counter counts to 0, MC changes to be low so that the
DMP begin to divide by N which is 8 in this paper. Hence, the modulus of the
DMP and the pulse-swallow counter is
M * = ( N + 1) S + N ( P − S ) = NP + S (1)
As mentioned in Fig. 1, P is set from 13 to 16, S from 0 to 7 while N is set to
be 8. Consequently, the modulus M* can vary from 104 to 135 continuously.
Taking the divide-by-2 into consideration, the overall divide ratio of the proposed
programmable divider is
M = 2M * (2)
Which means the divide ratio of the proposed programmable divider varies
from 208 to 270 in a step of 2.

2.1 Divide-by-2
Fig. 2 illustrates the structure of the proposed divide-by-2 frequency divider. The
divider consists of two same latches in cascade, namely master latch and slave

1855
latch. The output of the slave latch is inverted and fed back to the data input of the
master latch as shown in Fig. 2 (a). This kind of feedback enables the divide-by-2
to oscillate at a certain frequency fosc without any input signal. The self-oscillation
frequency fosc generally decides the operating frequency of a divider. The higher
the self-oscillation frequency is, the higher the speed of operation will be. Also
the input clock amplitude required in the vicinity of fosc is very small, it is usually
best to design 2fosc to be slightly higher than the input frequency fin of the divider
to allow robust divider operation [1]. The latch uses a pseudo-differential
structure which is different from the conventional frequency divider in which the
tail current source is removed.
QB Q
RL RL

D
M3 M4 M5 M6
DB
D Q D Q Q
Latch Latch
DB QB DB QB QB CLK CLKB
M1 M2
CLK
CLKB

(a) Proposed divide-by-2 as a master-slave flip-flop (b) Schematic of latch stage

Fig. 2 Structure of the divide-by-2

2.2 8/9 dual-modulus prescaler

Fig. 3 shows the block diagram of the proposed 8/9 DMP. It basically consists of a
4/5 synchronous dual-modulus circuit and a divide-by-2 asynchronous circuit.
The 4/5 synchronous dual-modulus circuit consists of three differential
D-flip-flops (DFF), as shown in Fig. 4 (a), and 2 NOR gates for modulus selection.
The first two flip-flops form a divide-by-4 circuit while the third flip-flop adds an
extra clock period delay for divide-by-5 [2], [3]. The propagation delay through
these flip-flops and NOR gates decide the maximum operating frequency of the
prescaler. So it is recommended to merge the flip-flops and the NOR gates
together to reduce the delay [4]. Fig. 4 (b) shows the schematic of the D flip-flop
with NOR. D1 and D2 are the input of the NOR logic while VB is a DC bias.
The divide-by-2 asynchronous divider adopts the topology of true single
phase clock (TSPC). Fig. 5 shows the schematic of the proposed TSPC DFF. The
reasons for using TSPC DFF instead of CML are that the input frequency of the
divide-by-2 asynchronous divider is not that high. So it is suitable to use TSPC.

1856
Compared with CML, TSPC has many advantages such as low power
consumption, single-ended input and smaller chip area. When the negative output
of the TSPC DFF feeds back to the input of the DFF, it works as a divide-by-2.
4/5 synchronous dual-modulus divider

D Q D Q D Q
CLK CLK CLK
QB QB QB
CLK

OUT
D Q
CLK
Divide-by-2 QB
MC=0, divide-by-8
asynchronous divider MC MC=1, divide-by-9

Fig. 3 Block diagram of 8/9 dual-modulus prescaler

QB Q Q QB

D D1
D2
DB VB
CLK CLKB CLKB CLK CLK CLKB CLKB CLK

(a) Schematic of D flip-flop without NOR (b) Schematic of D flip-flop with NOR
Fig. 4 Schematic of the DFFs used in 4/5 dual-modulus divider

CLK

Q
QB
D

Fig. 5 Schematic of the proposed TSPC DFF

2.3 The pulse-swallow counter

The block diagram of the pulse counter and swallow counter are shown in Fig. 6.
Both of the pulse counter and swallow counter consist of several DFFs and logic
gates. In the pulse counter, P0~P3 are the control bits of the counter, LD is a load
signal or reset signal for both the pulse counter and the swallow counter. The LD
signal enables the pulse counter and swallow counter to load the new counting

1857
control bits which means the new counting value. The MC signal in the swallow
counter is a modulus control signal for the 8/9 DMP.
P0 P1 P2 P3

D LV QB D LV QB D LV QB D LV QB OUT
DFF DFF DFF DFF
CLK CLK
LD
Q CLK
LD
Q CLK
LD
Q CLK
LD
Q

CLK
Q DFF1
D

LD

(a) Block diagram of the pulse counter

S0 S1 S2

D LV QB D LV QB D LV QB
CLKB DFF DFF DFF
CLK Q CLK Q CLK Q
LD LD LD

MC CLK
Q DFF2
D

LD

(b) Block diagram of the swallow counter

Fig. 6 Block diagram of the pulse counter and swallow counter

Fig. 7 illustrates the schematic of the TSPC DFF with reset signal and
load-value signal in the pulse counter and swallow counter. LD is the input node
of reset signal while LV is the input node of the load-value signal which is
supposed to connect the control bits of the counter.

D LD LDB LDB

LD QB LV
LD CLK

LD LD
CLK

LD CLK CLK
D LV

Fig. 7 Schematic of the TSPC DFF in pulse-swallow counter

3. Layout design and post simulation results

In this paper, the proposed programmable divider is fabricated in 65-nm CMOS

1858
process. The layout of the proposed programmable divider is shown in Fig. 8. The
area of the layout is 655×650μm2.The inductors in the layout are adopted in the
buffer which is to connect the divide-by-2 and the DMP. The buffer adopts a two
stage CML differential amplifiers with resistive loads and inductive peaking for
high-speed operation.

Fig. 8 Layout of the proposed programmable divider

The post simulation results show that the proposed programmable divider
can operate properly with the input frequency ranging from 16 GHz to 32 GHz in
normal condition. With the PVT variation, the divider can at least cover the
frequency range from 20 GHz to 28 GHz which is large enough for the input
frequency of 24~26 GHz for the application.
Fig. 9, Fig. 10 and Fig. 11 show the transient waves of the post simulation
results of divide-by-2, 8/9 DMP and the pulse-swallow counter, respectively.
All the post simulation transient waves are simulated in the condition that the
input frequency of the proposed divider is 32 GHz with the amplitude of 200 mV.
The control bits are that P3P2P1P0=1100, S2S1S0=100, which means the divide
ratio M=2M*=2(NP+S) =216. And the load is 50 Ω. The current consumption is
7.3 mA from a 1.2 V power supply.
In Fig. 10, the transient waves are the input signal, output signal of the 8/9
DMP and the MC signal, respectively. When MC is high, the 8/9 DMP is in
divide-by-9 mode while in divide-by-8 mode when MC is low. Four divide-by-9
periods can be counted in the output of the 8/9 DMP which corresponds to the
control bits S2S1S0=100.
As shown in Fig. 11, with the total divide ratio of 216 and the input

1859
frequency of 32 GHz, the output frequency is approximately 148.15 MHz.

Fig. 9 Post simulation transient waves of the divide-by-2

Fig. 10 Post simulation transient waves of the 8/9 dual-modulus prescaler

Fig. 11 Post simulation transient waves of the pulse-swallow counter

The performances of this work and some previously published

programmable frequency divider are summarized in Table 1 for comparison.

1860
 Table 1 Performance comparison of high-speed CMOS programmable frequency divider

Ref. Frequency range(GHz) Divide ratio Power(mW) Process

[2] 6~21 256~263 9 0.13-μm CMOS

[5] 7~12 256~268 (step of 4) 19.95 0.18-μm CMOS

[6] 18.69~22.8 7/8 6.7 90-nm CMOS

This work 16~32 208~270 (step of 2) 8.76 65-nm CMOS

4. Conclusions
This paper presents a programmable divider designed in 65-nm CMOS process
with divide ratio varied from 208 to 270 in a step of 2. The post simulation results
show that the divider can work properly with the input frequency from 16 GHz to
32 GHz while the power consumption is 8.76 mW.

References
[1] Singh, U.; Green, M., "Dynamics of high-frequency CMOS dividers," Circuits and
Systems, 2002. ISCAS 2002. IEEE International Symposium on , vol.5, no.,
pp.V-421,V-424 vol.5, 2002
[2] Yanping Ding; O, K.K., "A 21-GHz 8-Modulus Prescaler and a 20-GHz Phase-Locked
Loop Fabricated in 130-nm CMOS," Solid-State Circuits, IEEE Journal of , vol.42, no.6,
pp.1240,1249, June 2007
[3] Kim, D.D.; Choongyeun Cho; Jonghae Kim; Plouchart, J. -O, "Wideband mmWave CML
static divider in 65nm SOI CMOS technology," Custom Integrated Circuits Conference,
2008. CICC 2008. IEEE , vol., no., pp.627,634, 21-24 Sept. 2008
[4] Chihun Lee; Lan-Chou Cho; Shen-Iuan Liu, "A 44GHz Dual-Modulus Divide-by-4/5
Prescaler in 90nm CMOS Technology," Custom Integrated Circuits Conference, 2006.
CICC '06. IEEE , vol., no., pp.397,400, 10-13 Sept. 2006
[5] Jeng-Han Tsai; Yi-Wei Chung; Hung-Da Shih; Jian-Ping Chou, "A 7–12 GHz
multi-modulus frequency divider," Microwave Conference Proceedings (APMC), 2012
Asia-Pacific , vol., no., pp.1232,1234, 4-7 Dec. 2012
[6] Yang, Y.-C.; Lin, K.-T., "Programmable CMOS injection-locked frequency divider,"
Electronics Letters , vol.46, no.21, pp.1439,1441, October 2010

1861