2 3 4

4） Installation dimensions:
24 V voltage Max. output
300 mA
1. Safety Information output current 157.0
145.0 125.0
Overload Overload protection logic: 133.5
Safety Information protection on Trigger overload protection
higher-voltage and stop brake release
DANGER startup: ≥ 4.5 A
voltage output when the
detected overload duration
◆◆ This device contains high voltage, which may cause severe electric shock Overload
reaches or exceeds 200
and even death. protection
ms. The brake cannot be
on holding

180.0
156.0
◆◆ Exercise cautions when using or approaching the device connected to the released again until one
power supply. Brake release voltage: ≥ 3.5 A minute later.
output
Short-circuit
WARNING protection on
Short-circuit protection
logic: Trigger protection and
higher-voltage
◆◆ This product is designed to release the brake when the elevator experiences stop brake release voltage
startup: ≥ 6 A
a power failure. output when short-circuit
Short-circuit
◆◆ Improper installation of the product may cause safety risks. Therefore, occurs. The brake cannot
protection on
installation, commissioning, and maintenance of the product can be be released again until five
holding voltage:
performed only by personnel who have prior trainings on safety and product minutes later.
use. Protection ≥ 4.5 A
function When short-circuit occurs,
CAUTION parameters Short-circuit
the output voltage is 0. After
24 V output short-circuit is eliminated,
◆◆ Before electrical wiring, use a reliable insulating component to disconnect protection
the 24 V output is resumed
power supply of the elevator.

User Guide
immediately.
Battery
protection is on
When the device is inactive,
MCTC-ERB-A Series 2. Product Information when the device Figure 3 Installation dimensions
*19010850A01* ■■ Product Introduction
Battery
protection
is disconnected
from the mains
it does not consume any
battery except the battery's Install the device according to the installation dimensions, as shown in the
19010850 own consumption.
Electrical Brake Release Device
power and following figure:
This product is used to release the brake when the mains power fails. When the remains idle.
A01 mains power is normal, the battery is recharged. When the mains power fails, you
can press the Start and Common buttons on the operation panel simultaneously to
Undervoltage
release the brake in the non-door zone and press the Forced and Common buttons The brake is not released if
Battery protection for
simultaneously to release the brake in the door zone. the battery voltage is lower
undervoltage brake release: <
than 10.2 V.
■■ Model Description 10.2 V

MCTC - ERB - A1

1
Mark Series Mark Battery Provided The place is free of conductive materials,
MCTC Specialized for elevators A1 Yes Place corrosive gases, inflammable gases, metal
A2 No powder, oil mist, and dust.
Mark Type
Altitude < 2000 m
Introduction
ERB Electrical brake release

Ambient
Figure 1 Model description –10℃ to 50℃
temperature
Thank you for purchasing the MCTC-ERB-A series electrical brake release device.
Humidity 5% to 95％ RH, no condensing
This product is developed and produced by Inovance based on market ■■ Components Environment
requirements. It is easy to operate and reliable with performance. It releases the Vibration 5 Hz to 100 Hz, 1 m2/s3; 200 Hz, 0.1 m2/s3 Figure 4 Wall-mounting diagram
brake to stop the elevator at the expected position when the mains power fails. No. Item Storage
–20℃ to +60℃
The MCTC-ERB-A series product includes two types: with battery or without battery. 1 Indicator temperature

4. Wiring
You can select any one of them based on your requirements. Prepare a battery by 2 Button Protection
IP20
1 7

yourself if you select the one without battery. class

2
Electric brake release
3
6
Before using the product, read this guide carefully to fully understand the product device Cooling
Natural cooling ■■ Terminal Description
3 5
features. This guide describes the specifications, installation dimensions, port mode
4
Output terminal of the
types, and functions of the product. 4
brake release voltage The terminal marks are can be found in the silkscreen on the upper plate of the
device. The following table describes the terminals:
■■ Product Features 5
Door lock terminal in

This product is applicable to brakes whose strong excitation voltage is not higher
door zone
3. Installation Terminal Terminal
Function Remarks
than 110 V and maintaining voltage not higher than 80 V. 6 Burning terminal Type Mark
Mains power input
The maximum output current of strong excitation is 4 A. 7 ■■ Environment L 220 VAC input
terminal -
It provides output overload and short circuit protection during brake release as well Install this product in the elevator control cabinet and ensure sufficient space for 220 VAC input N 220 VAC input
as battery undervoltage protection. installation. The environment must meet the requirements in Table 1.
Figure 2 Components Positive terminal of
The battery can be provided with the product or be prepared by the user.
■■ Installation Guide ZQ1+ the brake release
Power is not consumed when the product is disconnected from the mains power ■■ Product Features Brake release voltage
and remains idle. Install the device using wall-mounting mounting. The device weighs 3.73 kg, -
voltage output Negative terminal
Table 1 Product features including the battery which weighs 1.69 kg.
You can determine the status of the brake release device based on indicators. ZQ2- of the brake release

■■ Guide Obtaining Mains power voltage

Input voltage Single-phase 220 VAC ± 15%
input 24 V
Positive terminal of The 24 V voltage output
The information in this document is subject to change without notice. Please the 24 V output can be used only by
acquire the latest version by the following means: Brake release 24 V voltage
Output Higher-voltage startup: 110 VDC the door zone sensor
1） Contact your product distributor. voltage output Negative terminal of
equipped for electrical
voltage Holding voltage: 80 VDC COM
output the 24 V output
2） Scan the QR code on the cover page of the guide to download the latest brake release.
version.
3） Visit Inovance's website http://www.inovance.com.
 5 6 7 8
The indicators are on the operation panel. They are green, red, yellow, and blue
Terminal Terminal ◆◆ The door lock signal is used to determine whether the car Installing the new battery
Function Remarks from left to right.
door is closed. If the signal indicates that the car door is not
Type Mark
closed, the brake release voltage is not output.
Input terminal of door Prepare a door zone Indicator Color State NOTE
MQ+ zone signal that is sensor yourself; Steady ON: Brake release voltage is output.
Indicator of brake 3. Logic of brake release voltage output 1） Push the new battery into the box
high level valid Cannot connect to the Green Steady OFF: Brake release voltage is not
release voltage output 1） During brake release, the electrical brake release device outputs 110 V higher- by following the arrow direction.
Door zone Input terminal of door door zone signal from the output. voltage startup for 2s. Then, it outputs 80 V holding voltage for up to 120 s.
signal input zone signal that is low safe circuit; Steady ON: Overload or short-circuit occurs in 2） The electrical brake release device can output 110 V voltage for 2s and 80 V
MQ- level valid (Connect Only support door zone the brake release output circuit.
Fault indicator Red voltage for 120s for three consecutive times. After three consecutive times of
the signal to the COM sensor that is high level Steady OFF: The brake release output is voltage outputs, you need to wait for 10 minutes before the device can release
terminal). valid. normal. the brake again.
Positive input Use a door lock sensor. Steady ON: The battery is full. 2） Connect the two cables between
MS+ terminal of the door If you do not use it,
Slow blinking slowly: The battery is the power board and the battery.
5. Maintenance
Door lock lock signal short the MS+ and MS- Battery indicator Yellow
discharging or recharged.
signal input Negative input terminals. That is, the
door lock is closed by Quick blinking: The battery level is low.
MS- terminal of the door
lock signal default. Steady ON: The elevator is at the door zone Battery Replacement Information
position when the mains power fails.
Door zone indicator Blue CAUTION
■■ Wiring Steady OFF: The elevator is at the non-door
3） Install the battery holder, and
zone position when the mains power fails. Battery maintenance:
The following figure shows the wiring: tighten the two screws on the
◆◆ It is recommended that the battery be replaced every two years. battery holder with a screwdriver.
◆◆ When the battery is recharged, the battery indicator is ON. When
Electrical brake ◆◆ Before using the device for the first time, ensure that the battery is charged
the battery is not recharged, you can press the Start button and
release device Input
for 12 h.
hold for 1s, the indicator is ON and shows the status depending
power Power
cable distribution
N N box
NOTE on the battery level. After three minutes, the indicator is off ◆◆ It is recommended that the battery be recharged at least once half a year.
L L again. Battery replacement:
Battery
◆◆ Disconnect the device from the mains power.
4） Push down the front cover, and
■■ Buttons
BAT+ BAT- Door lock
sensor
MQ-
◆◆ Take off metal accessories such as ring and watch. then tighten the four bolts with a
BAT- MQ+
DQ-
There are three resettable buttons, which are Start, Common, and Forced, on the ◆◆ Use a screwdriver with an insulated handle, and do not put any metal objects screwdriver.
DQ+ Door zone sensor panel. The brake release device considers a button effective when you hold it down on the battery.
BAT+
COM and ineffective when you release it.
Photoelectric
◆◆ Never short or reverse the positive and negative poles of the battery. Connect
24v sensor/Magnetic

■■ Functions of the Electrical Brake Release Device the red cable to the positive terminal and the black cable to the negative
sensor

terminal.
1. Activating the battery
Output
Brake
power
release coil

■■ Battery Replacement Guide 6. Revision History

cable
ZQ2- ZQ2-
When the device is disconnected from the mains power, the battery and backend
ZQ1+ ZQ1+ load are disconnected. You can activate the battery by using the Start button. The
procedure is described as follows: Removing the old battery
Date Version Revision
Figure 5 Wiring 1） Press the Start button and hold for 1s. The battery indicator is ON (yellow),
indicating that the battery is activated. October 2018 A00 First release
◆◆ The door zone sensor must be high level valid. That is, it After activation, the battery keeps providing power for three minutes and then is November 2020 A01 Made minor corrections
1） Use a screwdriver to loosen the four
outputs high level in door zone and low level in non-door automatically powered off. screws and remove the front cover
zone.
NOTE 2） After the battery is automatically powered off, perform step 1) if you need to by following the arrow direction.
activate it again.
■■ External Device Specifications

Warranty Agreement
Battery specifications: ◆◆ 1. Under brake release state, the battery is automatically
powered off three minutes after the brake is released.
Output ◆◆ 2. Before the device releases the brake, you must activate the
Device Capacity Dimensions
Voltage NOTE battery. 1. Inovance provides an 18-month free warranty to the device itself from the date of
2） Remove the two cables between manufacturing for the failure or damage under normal use conditions.
Lead-acid 2. Brake release operation
12 V ≥ 7 AH 151 mm x 100 mm x 65 mm the power board and the battery.
battery 2. Within the warranty period, maintenance will be charged for the damage caused
When the mains power fails, the electrical brake release device works as follows:
by the following reasons:
Door zone sensor specifications:
a. Improper use or repair/modification without prior permission
Power
Input Max. Input Output Max. Output
Device failure b. Fire, flood, abnormal voltage, natural disasters and secondary disasters
Voltage Current Voltage Current
c. Hardware damage caused by dropping or transportation after procurement
Photoelectric
24 V 200 mA 24 V 5 mA Elevator in door No Press Start and Common simultaneously 3） Unscrew the two screws from the d. Operations not following the user instructions
sensor zone? to output brake release voltage battery holder and remove the
Magnetic e. Damage out of the device (for example, external device factors)
24 V - - 5 mA holder.
switch 3. The maintenance fee is charged according to the latest Maintenance Price List of
Yes
Inovance.
Press Forced and Common
simultaneously to output brake 4. If there is any problem during the service, contact Inovance’s agent or Inovance

4. Operation Guide directly.

release voltage

5. Inovance reserves the rights for explanation of this agreement.

4） Pull out the battery by following the
■■ Indicators Release Forced or Press the Release Start or Elevator moves
arrow direction.
Common buttons for at Common to door zone
least 120s
Electrical brake Suzhou Inovance Technology Co., Ltd.
release device
Stop brake release Address: No.16, Youxiang Road, Yuexi Town, Wuzhong District, Suzhou 215104, P.R.
voltage output China
Website: http://www.inovance.com
Brake Door
Fault Battery
release zone
Elevator
stops

Start Common Forced Figure 6 Brake release process