SMART CARD

PERSONALISER

INSTALL GUIDE
Revision 1.3
 Copyright

Important: the technical information contained in this

manual is property of Matica System S.p.A. and is secured
by copyright. The terms of the license define and specify
permitted uses and other limitations.

Reproduction of any part of this manual, in any form, is

forbidden without the explicit written permission of Matica
System S.p.A.

Technical information contained in the present manual is

subject to change without notice. If not otherwise specified,
any reference to companies, names, dates and addresses is
purely incidental and is only intended to illustrate the use of
the Matica System S.p.A. product.

Every care has been taken in the collection and verification

of the documentation inserted in this manual; nevertheless
Matica System S.p.A. cannot assume any responsibility
deriving from its use.

Copyright © 2015 Matica System S.p.A.

All rights reserved
Published by Matica System S.p.A.

Printed in Italy
Issue: February 2015
Revision 1.3

Matica System S.p.A.

via Guido Rossa, 4/6
20037 – Paderno Dugnano
MILAN - ITALY
Phone +39.02.92272501
Fax +39.02.91084372

E-mail: [email protected]
Web: http://www.maticatech.com

S5000C Install Guide Rev. 1.3 Page 2/36

 Contents

Table of contents

Preliminary – Software installation quick guide ....................... 4

Paragraph 1 – Maticard Pro installation ..................................... 5

Paragraph 2 – S7000 Desktop installation ................................ 9

Paragraph 3 – Machine plugging.................................................13

Paragraph 4 – USB Port setting...................................................16

Paragraph 5 – Contact Chip Driver installation........................19

Paragraph 6 – Contactless Chip Driver installation ................22

Paragraph 7 – Contact/Contactless setting for Win7 .............25

Paragraph 8 – MM Config setting ................................................28

Paragraph 9 – Machine testing ....................................................32

S5000C Install Guide Rev. 1.3 Page 3/36

 Preliminary – Software installation quick guide

Preliminary – Software installation quick guide

Please find the USB Pen Drive of the machine, containing all the documentation
and software needed, inside the keys bag.

Run the Maticard Pro software setup file placed in the Software\Maticard Pro
USB Pen Drive folder. It's suggested to install the Maticard Pro software in the
C:\MATICA\Programs\Maticard Pro folder.

Run the S7000 Desktop software setup file placed in the Software\Maticard Pro
USB Pen Drive folder.

Copy the possible updated files of the Maticard Pro software, placed in the
Software\Maticard Pro\Maticard Pro Update USB Pen Drive folder, into the
Maticard Pro installation folder.

Copy the possible updated files of the MM Main software, placed in the
Software\Maticard Pro\MM_Main USB Pen Drive folder, into the
C:\MATICA\7000\MM_Main folder.

Copy the machine configuration file (.mpm), placed in the USB Pen Drive root,
into the C:\MATICA\7000\MP_Files folder.

Copy the configuration license file (.lic), placed in the USB Pen Drive root, into
the C:\MATICA\7000\MM_Main folder.

S5000C Install Guide Rev. 1.3 Page 4/36

 Paragraph 1 – Maticard Pro installation

Paragraph 1 – Maticard Pro installation

To install the Maticard Pro program, run the Setup_Maticard_Pro.exe file from
the Software/Maticard Pro directory of the Machine USB Pen Drive.

Click Next in the Maticard Pro InstallShield Wizard welcome window.

S5000C Install Guide Rev. 1.3 Page 5/36

 Paragraph 1 – Maticard Pro installation

Click Next in the Maticard Pro InstallShield Wizard copyright window.

Click Next to accept the license terms. Please note that the operative systems
required by the program are specified in the License Agreement window.

S5000C Install Guide Rev. 1.3 Page 6/36

 Paragraph 1 – Maticard Pro installation

Click Next in the Destination Folder window.

Select the Typical setup type and click Next.

S5000C Install Guide Rev. 1.3 Page 7/36

 Paragraph 1 – Maticard Pro installation

Click Install to start the installation.

When the installation has been completed, click Finish.

Copy the possible updated files of the Maticard Pro software, placed in the
Software\Maticard Pro\Maticard Pro Update USB Pen Drive folder, into the
Maticard Pro installation folder.

S5000C Install Guide Rev. 1.3 Page 8/36

 Paragraph 2 – S7000 Desktop installation

Paragraph 2 – S7000 Desktop installation

To install the S7000 Desktop program, run the Setup S7000 Desktop exe file
from the Software/Maticard Pro directory of the Machine USB Pen Drive.

Click Next in the S7000 Desktop InstallShield Wizard welcome window.

S5000C Install Guide Rev. 1.3 Page 9/36

 Paragraph 2 – S7000 Desktop installation

Click Next in the S7000 Desktop InstallShield Wizard copyright window.

Click Install to start the installation.

S5000C Install Guide Rev. 1.3 Page 10/36

 Paragraph 2 – S7000 Desktop installation

When the installation has been completed, click Finish.

This setup has installed the MM_Main and the MM_Remote_Manager programs.
The two programs have been put in the Startup directory in order to get them
both automatically running.

S5000C Install Guide Rev. 1.3 Page 11/36

 Paragraph 2 – S7000 Desktop installation

Restart the PC.

Click Unblock in the Windows Security Alert about the MM Remote Manager
program.

Click Unblock in the Windows Security Alert about the MM Main program.

S5000C Install Guide Rev. 1.3 Page 12/36

 Paragraph 3 – Machine plugging

Paragraph 3 – Machine plugging

Power on the S5000C machine, then plug the first USB cable to the computer
and to the machine connector with the PC label.

The Found New Hardware Wizard window will be displayed.

Select the “No, not this time” option and click Next.

S5000C Install Guide Rev. 1.3 Page 13/36

 Paragraph 3 – Machine plugging

Select the Advanced option and click Next.

Browse the Drivers\USB to COM Driver\FDTI USB-COM422-PLUS1 Converter

Driver\CDM20814_WHQL_Certified directory of the Machine USB Pen Drive and
click Next.

S5000C Install Guide Rev. 1.3 Page 14/36

 Paragraph 3 – Machine plugging

When the USB Serial Converter driver installation is completed, click Finish.

Now another Found New Hardware Wizard window will be displayed.

Repeat the same procedure of the USB Serial Converter driver installation also
for the USB Serial Port installation.

S5000C Install Guide Rev. 1.3 Page 15/36

 Paragraph 4 – USB Port setting

Paragraph 4 – USB Port setting

The port assigned by the PC to the USB driver must be changed in COM2 Port.
Right-click the My Computer icon and select the Properties command.

Select the Hardware tab of the System Properties window an click Device
Manager.

S5000C Install Guide Rev. 1.3 Page 16/36

 Paragraph 4 – USB Port setting

Double-click the USB Serial Port icon.

Select the Port Settings tab of the Properties window and click Advanced.

S5000C Install Guide Rev. 1.3 Page 17/36

 Paragraph 4 – USB Port setting

Select the COM2 option into the COM Port Number combo box of the Advance
Settings window and click OK.

Be sure that no other device will be already set on the COM2; otherwise a
Communication window will be displayed, asking if the PC has to continue with
the COM setting change.

Check in the Device Manager window that the installed USB Serial port is now
assigned to the COM2.

S5000C Install Guide Rev. 1.3 Page 18/36

 Paragraph 5 – Contact Chip Driver installation

Paragraph 5 – Contact Chip Driver installation

Browse the Drivers\PCSC SmartCard Reader Driver\Gemalto - ID-Bridge CT30

directory of the Machine USB Pen Drive.

Run the GemPcCCID_en-us_32.msi file if the PC Operating System is 32-bit, or

run the GemPcCCID_en-us_64.msi file if the PC Operating System is 64-bit.

Click the Next button in the “GemPcCCID Setup” window.

S5000C Install Guide Rev. 1.3 Page 19/36

 Paragraph 5 – Contact Chip Driver installation

Accept the terms in the License Agreement and then click the Next button.

Click the Install button.

S5000C Install Guide Rev. 1.3 Page 20/36

 Paragraph 5 – Contact Chip Driver installation

Click the Finish button to exit the “GemPcCCID Setup” window.

Check that the USB Smart Card Reader is present in the “Smart card
readers”.

S5000C Install Guide Rev. 1.3 Page 21/36

 Paragraph 6 – Contactless Chip Driver installation

Paragraph 6 – Contactless Chip Driver installation

Browse the Drivers\PCSC SmartCard Reader Driver\Gemalto - ID-Bridge CT30

directory of the Machine USB Pen Drive and run the following file:
SCL3711_INST_WIN_EN_V1.12_setup.exe .

Click Next in the NFC Reader Writer InstallShield Wizard copyright window.

S5000C Install Guide Rev. 1.3 Page 22/36

 Paragraph 6 – Contactless Chip Driver installation

Accept the terms in the License Agreement and then click the Next button.

Click the Install button.

S5000C Install Guide Rev. 1.3 Page 23/36

 Paragraph 6 – Contactless Chip Driver installation

Click the Finish button to exit the “InstallShield Wizard” window.

Check that the SCL3711 reader & NFC device is present in the “Smart card
readers”.

S5000C Install Guide Rev. 1.3 Page 24/36

 Paragraph 7 – Contact/Contactless setting for Win7

Paragraph 7 – Contact/Contactless setting for Win7

Starting from Windows 7, Microsoft included some new features in the Smart
Card Service.

If the deployment uses only non-Plug and Play smart card solutions, smart
card Plug and Play can be disabled by a local administrator on a client
computer. Disabling smart card Plug and Play prevents smart card drivers, also
known as smart card mini-drivers, from downloading and prevents smart card
Plug and Play prompts.

Perform the following procedure to disable smart card Plug and Play in local
Group Policy.

On a client computer, click Start, type gpedit.msc in the Search programs

and files box, and then press Enter.

In the console tree under Computer Configuration, click Administrative

Templates.

S5000C Install Guide Rev. 1.3 Page 25/36

 Paragraph 7 – Contact/Contactless setting for Win7

In the details pane, double-click Windows Components.

Then double-click Smart Card.

S5000C Install Guide Rev. 1.3 Page 26/36

 Paragraph 7 – Contact/Contactless setting for Win7

Right-click Turn on Smart Card Plug and Play service, and then click Edit.

Click Disabled, and then click OK.

S5000C Install Guide Rev. 1.3 Page 27/36

 Paragraph 8 – MM Config setting

Paragraph 8 – MM Config setting

Run the MM Config program.

In the MM Config window, check mark the Work on embedded HW option.

Then click Load File.

S5000C Install Guide Rev. 1.3 Page 28/36

 Paragraph 8 – MM Config setting

Load the Machine configuration file (e.g. 5000-xxxxx.mpm) placed on the root
of the S7000 USB Pen Drive.

If the machine configuration file .mpm is outdated respect to the

Master_MachineConfig.xml file version, a warning message will be displayed
advising that the mpm file will be updated to the new xml version.

S5000C Install Guide Rev. 1.3 Page 29/36

 Paragraph 8 – MM Config setting

Otherwise, if the machine configuration file .mpm is more recent respect to the
Master_MachineConfig.xml file version, a warning message will be displayed
advising that the configuration editing will be disable.
In this case the Master_MachineConfig.xml file version must be updated.

In the MM Config window click Write To Machine and a confirmation window

will be displayed.

Now in the MM Config window click save File to store the machine
configuration file .mpm into the C:\MATICA\7000\MP_Files directory.

S5000C Install Guide Rev. 1.3 Page 30/36

 Paragraph 8 – MM Config setting

Save a second copy of the MPM file (e.g. S5000) in order to keep the factory
original unchanged.

In the MM Config window click Exit.

S5000C Install Guide Rev. 1.3 Page 31/36

 Paragraph 9 – Machine testing

Paragraph 9 – Machine testing

Run the Maticard Pro program. Click the second button on the right
(screwdriver icon) and check that the default machine will be the desired one.
Then click the first button on the left (notebook icon) to create a job.

Now digit the Job name and select the Layout properties tab.

S5000C Install Guide Rev. 1.3 Page 32/36

 Paragraph 9 – Machine testing

Click Open and create a test mpl layout file name in the displayed window.
Then click Edit to display the Maticard Editor window.

To test the machine functionality, save the empty job selecting the Save
Layout and Exit command from the File menu in the Maticard Editor window.

S5000C Install Guide Rev. 1.3 Page 33/36

 Paragraph 9 – Machine testing

Click Save in the Job Edit window and the new job will be displayed
into the Maticard Pro window.

Click the Reset button and the machine will restore all the modules.

If the machine cover is open, a warning message will be displayed.

Close the cover and click Continue.

S5000C Install Guide Rev. 1.3 Page 34/36

 Paragraph 9 – Machine testing

The Reset status window will be displayed.

Load some cards into the Feeder module; then click Production button in the
Maticard Pro window and the Start cards production window will be displayed.

S5000C Install Guide Rev. 1.3 Page 35/36

 Paragraph 9 – Machine testing

Click the first button on the left to start the production.

If the production is finished well, the machine is fully installed.

S5000C Install Guide Rev. 1.3 Page 36/36