NIST CRM and IUPAC Standards List

v. 1
January 2024

ORDERING GUIDE

More at hach.com

Item Number 1479010 Item Number 256949

NIST Traceable standard, single analyte:
Analyte Part Number Concentration Analyte Part Number Concentration

Aluminum 1417442 100 mg/L as Al Lead 2374820 10 mg/L as Pb

1261742 100 mg/L as Pb
Barium 1461142 1000 mg/L as Ba 1279642 1000 mg/L as Pb

Boron 191442 1000 mg/L as B Magnesium 1479442 1000 mg/L as Mg

Cadmium 1402442 100 mg/L as Cd Manganese 2605820 10 mg/L as Mn (PK 20- 2 mL

­ampules)
Calcium 2305442 10 +/- 0.14 mg/L as Ca2+ 2112820 25 mg/L as Mn (PK 20- 2 mL
4457649 100 +/- 1 mg as Ca2+ ­ampules)
2240349 1000 mg +/- 8 mg/L as Ca2+ 1279142 1000 mg/L as Mn

Hexavalent 81042H 50 mg/L as Cr6+ Molybdenum 1418742 10 mg/L as Mo

­Chromium 1425610 12.5 m/L as Cr6+ (PK 16- 10 mL 1418642 100 mg/L as Mo
ampules)
1415142 50 mg/L as Cr3+ Nickel 1417642 1000 mg/L as Ni

Cobalt 2150342 1000 mg/L as Co Nitrate 204649 1.0

30749 10.0 +/- 0.1 mg/L as NO3-N
Copper 12932 10 mg/L as Cu 2415132 15 mg/L as NO3-N
12842 100 mg/L as Cu 194749 100 mg +/- 1 mg/L as NO3-N
259342 1000 mg/L as Cu 1426010 500 mg/L as NO3-N
1279249 1000 +/- 10 mg/L as NO3-N
Fluoride 40502 0.2 mg/L as F-
40505 0.5 mg/L as F- Phosphate 256949 1 mg/L as PO4
40508 0.8 mg/L as F- 1424342 15 mg/L as PO4
29149 1.00 +/- 0.02 mg/L as F- 1436716 30 mg/L as PO4
40512 1.2 mg/L as F- 17110 50 mg/L as PO4 (PK 16- 10 mL
40515 1.5 mg/L as F- Ampules)
40520 2.00 mg/L +/- 0.04 mg/L F- 1436832 100 mg/L as PO4
2797149 5.0 mg F/L 1424210 500 mg/L as PO4 (PK 16- 10 mL
35949 10.0 +/- 0.2 mg/L F- Ampules)
23249 100 +/- 2 mg/L F-
Phosphorous 2321142 1000 mg/L as P
Hardness 218710 10,000 mg/L as CaCO3 (PK 16- 10 mL (See also LCA720
­(calcium) ampules) and LCA721)

Iron 13949 1 mg/L as Fe Potassium 2351749 100 mg/L as K+

14049 10 mg/L as Fe 1479010 250 mg/L as K+ (PK 16- 10 mL
1425310 25 mg/L as Fe (PK 16 – 10 mL Ampules)
Ampules)
1417542 100 mg/L as Fe
227142 1000 mg/L as Fe
Continued on next page
 NIST CRM and IUPAC Standards List v. 1
January 2024

NIST Traceable standard, single analyte: Mixed Standards:

Analyte Part Number Concentration Part Analytes and
Applicable for TNTplus vial tests
­Number Concentrations
Silica 110649 1 mg/L as SiO2
140349 10 mg/L as SiO2 LCA720 COD – 500 mg/L - TNT822 COD, 20-1500 mg/L O2
111729 50 mg/L as SiO2 PO4-P – 10.0 mg/L - TNT825 Hg-free COD, 25-1000 mg/L O2
19449 1000 mg/L as SiO2 NH3-N – 25.0 mg/L* - TNT845 Phosphate, 2-20 mg/L PO4-P
NO3-N – 25.0 mg/L - TNT832 Ammonia, 2-47 mg/L NH3-N
Sodium 1474949 1000 mg/L as Na TN – 50.0 mg/L - TNT836 Nitrate, 5-35 mg/L NO3-N
- TNT828 Total Nitrogen, 20-100 mg/L TN
Sulfate 257849 50 mg/L as SO42+
89149 100 mg/L as SO42+ LCA721 COD – 50 mg/L - TNT821 COD, 3-150 mg/L O2
2175749 1000 mg/L as SO42+ PO4-P – 1.0 mg/L - TNT843 Phosphate, 0.05-1.5 mg/L
1425249 2500 mg/L as SO42+ NH3-N – 1.0 mg/L* PO4-P
NO3-N – 6.0 mg/L - TNT830 Ammonia, 0.015-2.0 mg/L
Zinc 1424610 25 mg/L as Zn (PK 16- 10 mL TN – 7.0 mg/L NH3-N
­Ampules) - TNT835 Nitrate, 0.2-13.5 mg/L NO3-N
237842 100 mg/L as Zn - TNT826 Total Nitrogen, 1-16 mg/L TN
1417742 1000 mg/L as Zn
*Ammonia is not NIST traceable.

Item Number Item Number

LCA720 LCA721

©Hach Company, 2024. All rights reserved.

In the interest of improving and updating its equipment, Hach Company reserves the right to alter specifications to equipment at any time. Continued on next page
 NIST CRM and IUPAC Standards List v. 1
January 2024

Certified Reference Materials CRM according to ISO 17034:2017

pH Buffers IUPAC Standard Solution according DIN EN ISO 17034:2017 (D-RM-15184-01-00) with Certificate of
Analysis* reporting exact pH buffer value.

pH (500 mL)
Certified Reference Material
Part Number pH Traceability: Calibration at 25°C with Certified Reference Material from DFM1
Certificate of Analysis Certificate Nr.511 CRM2204 Lot 22042801JA

Accreditation: Hach Lange GmbH is accredited by the German accreditation authority DAkkS as registered

S11M009 1.09 ±0.02 at 25°C reference material producer D-RM-15184-01-00 according to DIN EN ISO 17034:2017 and registered
calibration laboratory D-K-15184-01-00 according to DIN EN ISO/IEC
Storage:17025:2018 Before use: store in unopened aluminum bag.After opening: store in capped bottle
in normal atmospheric conditions at a temperature between 0 and 30°C. Do not
expose to light.
Manufacturer: HACH LANGE GmbH

S11M001 1.679 ±0.010 pH at 25°C Königsweg 10

D-14163 Berlin Preparation of standard: Potassium chloride, reagent grade, was dissolved in low conductivity demineralised
water. Until bottling, the solution was protected from evaporation and
( ++49 (30) 8 09 86-0
contamination. For protection against evaporation and microbiological growth, the
bottles are placed in airtight aluminum bags.

S11M002 4.005 ±0.010 pH at 25°C

LE
Object: Certified secondary Conductivity Standard

Type: KCL 0.1D 12.85 mS/cm ± 0.35 % (25°C) Uncertainty: The expanded uncertainty assigned to the measurement results is obtained

S11M010 4.65 ±0.02 pH at 25°C

by multiplying the standard uncertainty by the coverage factor k = 2.
It has been determined in accordance with EA-4/02M:2013. The value of
Intended use: Standard conductivity solution for calibration of measuring set ups
the measurand lies within the assigned range of values with a probability of 95%.
for conductivity.

LE
P
Order number: S51M002

S11M003 6.865 ±0.010 pH at 25°C

Homogeneity: 15 bottles were selected for analytical control. Results from different bottles

M
Serial number: C03023 showed no statistically significant differences, nor was there any correlation
between values obtained and the bottling sequence.
Certified value: κ= (12.857 ± 0.039) mS/cm (25°C)

P
A
Number of pages: 2

S11M004 7.000 ±0.010 pH at 25°C

Stability: When stored in an unopened aluminum bag, the certified value is guaranteed for 2
Date of release: December 13, 2022 years from the date of issue of the certificate.

M
S
Shelf life unopened bag: December 13, 2024

Shelf life open bag: 3 month

S11M005 7.413 ±0.010 pH at 25°C

A
Recommended use: First use: write the opening date on the bottle using an indelible pen. Cap bottle as
soon as aliquot is taken for calibration. Tick a box on the bottle after each opening.
Never pour the used aliquot back into the bottle. Always follow Good Laboratory

S
Practice and the recommendations regarding shelf life printed on the bottle.

S11M006 9.180 ±0.010 pH at 25°C Method of Analysis: The calibration of the conductivity solutions is done
by using a test assembly containing a platinised 4-pole measuring cell and a
LCR meter. The measurement is traceable to primary standard.

S11M011 9.23 ±0.02 pH at 25°C

Document version: 1 issued on December 13, 2022

Date Deputy head of the calibration laboratory

S11M007
1) Danish Fundamental Metrology, Hørsholm, Denmark

10.012 ±0.010 pH at 25°C December 13, 2022 Bernd Seidl

Page1

S11M008 12.45 ±0.05 pH at 25°C

Page 2

Conductivity

Part Number Conductivity Value

S51M002 12.85 mS/cm ±0.5% (k=2) at 25°C

S51M013 25.0 µS/cm ±5.0 % at 25°C

S51M001 111.3 mS/cm ±0.5% (k=2) at 25°C

S51M004 1015 µS/cm ±0.5 % at 25°C

S51M003 1408 µS/cm ±0.5 % at 25°C Item Number S11M011 Item Number S51M001

World Headquarters: Loveland, Colorado USA | hach.com

United States 800-227-4224 fax: 970-669-2932 email: [email protected]
Outside United States 970-669-3050 fax: 970-461-3939 email: [email protected]
©Hach Company, 2024. All rights reserved.
In the interest of improving and updating its equipment, Hach Company reserves the right to alter specifications to equipment at any time. DOC062.53.20359.Mar24