Scribd
Upload
75 views2 pages

Plates of S690Q Steel Grade. Fine-Grain Structural Steel After Quenching and Tempering

This document provides information about plates of S690Q steel grade, including a product description, available dimensions, mechanical properties, chemical composition, tolerances, welding requirements, and contact information. S690Q is a high-strength structural steel with a minimum yield strength of 690 MPa, supplied as quenched and tempered plates. Plates are available in thicknesses from 8-100 mm and widths up to 3200 mm, with maximum plate dimensions depending on thickness.

Uploaded by

amr.elsaeid53
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
75 views2 pages

Plates of S690Q Steel Grade. Fine-Grain Structural Steel After Quenching and Tempering

This document provides information about plates of S690Q steel grade, including a product description, available dimensions, mechanical properties, chemical composition, tolerances, welding requirements, and contact information. S690Q is a high-strength structural steel with a minimum yield strength of 690 MPa, supplied as quenched and tempered plates. Plates are available in thicknesses from 8-100 mm and widths up to 3200 mm, with maximum plate dimensions depending on thickness.

Uploaded by

amr.elsaeid53
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Plates of S690Q steel grade

Fine-grain structural steel after quenching and tempering

Products description
S690Q – structural high-strength steel with minimum yield strength of 690 MPa supplied in quenched and tempered
condition (Q). Plates of S690 steel grade comply with EN 10025-6 standard. It is typically used in structures bearing
extreme loads – in the production of mining and heavy construction equipment, crane facilities, offshore drilling rigs
and supports for offshore wind mills as well as in the construction of bridges and trestles.

Available dimensions
Plates of S690 steel grade are available with thicknesses of 8-100 mm for Q and QL quality groups and with thicknesses
of 8-50 mm for QL1 quality group. Available width of plates is up to 3200 mm, length – up to 12200 mm. With the plate
thickness of 100 mm and plate width of 1600 mm, the maximum length is 7500 mm*. Plates with thickness up to 50
mm are supplied with edges trimmed, with thickness of 51 to 100 mm – with the edge flame cut.
* – maximum weight is 9,5 ton

Mechanical properties under EN 10025-6


Yield strength, min
Steel grade Thickness, mm Tensile strength, MPa Elongation, min %
MPa
S690Q, QL, QL1 ≥8 t ≤50 690 770-940 14
S690Q, QL >50 t ≤100 650 760-930 14

Impact energy KV, min J


Steel grade
0 -20 -40 -60
S690Q 40 30 - -
S690QL 50 40 30 -
S690QL1 60 50 40 30

Chemical composition (mах %)


According to EN 10025-6

С Si Мn Р S N B Сг Сu Мо Nb Ni V

0.020- 0.010-
0.20 0.80 1.70 0.015 0.005 1.50 0.50 0.70 0.06 2.00 0.12
0.025 0.015

According to Metinvest production

С Si Мn Р S N B Сг Сu Мо Nb Ni V

0.19 0.35 1.15 0.015 0.006 0.009 0.002 0.65 0.30 0.50 0.03 0.90 0.07

Carbon equivalent
CEV
Thickness, mm
EN 10025-6 Metinvest production
< 50 0.65 0.59
> 50 0.77 0.73

metinvestholding.com 1
Tolerances
Thickness According to EN 10029 Class A

Length and width According to EN 10029

Flatness According to EN 10029 Class N

Surface properties According to EN 10163 Class A

Welding
Steels specified in this document possess limited weldability properties since steel behavior before and after welding
depends not only on the material, but its dimensions and shapes as well as operating conditions of goods.
General requirements to arc welding of steels specified herein shall be in line with EN 1011-2.

Contacts

Europe

Metinvest Western Europe Metinvest South-East Europe


Via XII Ottobre, 3 1 Dobrudzha Str., 1000 Sofia, Bulgaria
16121 Genova, Italy Tel.: +359 886 007 204
Tel.: +39 010 576 29 11 E-mail: [email protected]
Fax: +39 010 576 29 90
E-mail: [email protected]

GULF countries

Metinvest International Gulf branch office


Jebel Ali Free Zone, building LOB 17,
Floor 3 PO Box 263027, Dubai, UAE
Tel.: 971 4 881 19 40
Fax: +971 4 881 19 57
E-mail: viktor.vukusic@metinvest-
international.com

World

Metinvest International
2 Rue Vallin, Geneva
1201, Switzerland
Tel.: +41 22 906 18 28
E-mail: [email protected]

metinvestholding.com 2

You might also like