11/3/17, 10(31 pm

AUDIO / VIDEO AUDIO AND VISUAL SYSTEM(for Radio and Display Type) DTC CHECK / CLEAR

CHECK DTC (CHECK USING GTS)

a. Connect the GTS to the DLC3.

b. Turn the ignition switch to ON.

c. Turn the GTS on.

d. Enter the following menus: Body Electrical / Navigation System / Trouble Codes.
Body Electrical > Navigation System > Trouble Codes

Execute

e. Check the details of the DTC(s).

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display
Type)>DIAGNOSTIC TROUBLE CODE CHART

CLEAR DTC (CLEAR USING GTS)

a. Connect the GTS to the DLC3.

b. Turn the ignition switch to ON.

c. Turn the GTS on.

d. Enter the following menus: Body Electrical / Navigation System / Trouble Codes.

e. Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs

Execute

START DIAGNOSTIC MODE

HINT:
· Illustrations may differ from the actual vehicle screen depending on the device settings and options.
Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
· After the ignition switch is turned to ON, check that the map is displayed before starting diagnostic mode.
Otherwise, some items cannot be checked.

a. Method 1
i. Start the engine.

ii. While pressing and holding the "AUDIO" switch of the radio and display receiver assembly, operate the light
control switch: Off → Tail → Off → Tail → Off → Tail → Off.

iii. Diagnostic mode starts and the "Service Menu" screen will be displayed. Service inspection starts
automatically and the result will be displayed.

https://toyotamanuals.com.au/docs/hilux-service-repair-manual-jul-15-current/N00148/manual/repair/contents/RM100000000LGZ5.html Page 1 of 9
 11/3/17, 10(31 pm

*A for LHD
*B for RHD

b. Method 2
NOTICE:
If the operation fails and diagnostic mode cannot be entered, turn the radio and display receiver assembly
screen display on and off once, and then perform the procedures listed below from the first step again. (Only
turning the radio and display receiver assembly power supply on and off will not work.)

i. Start the engine.

ii. Turn the radio and display receiver assembly screen display off.

iii. Turn the radio and display receiver assembly power supply off.

iv. Press the ">" switch 5 times, and then press the "<" switch 5 times within 15 seconds.

v. Diagnostic mode starts and the "Service Menu" screen will be displayed. Service inspection starts
automatically and the result will be displayed.

https://toyotamanuals.com.au/docs/hilux-service-repair-manual-jul-15-current/N00148/manual/repair/contents/RM100000000LGZ5.html Page 2 of 9
 11/3/17, 10(31 pm

*A for LHD
*B for RHD

FAILURE DIAGNOSIS

a. The "Failure Diagnosis" screen will be displayed by selecting "Failure Diagnosis" on the "Service Menu" screen.

https://toyotamanuals.com.au/docs/hilux-service-repair-manual-jul-15-current/N00148/manual/repair/contents/RM100000000LGZ5.html Page 3 of 9
 11/3/17, 10(31 pm

SYSTEM CHECK

a. The "System Check Mode" screen will be displayed by selecting "System Check" on the "Failure Diagnosis"
screen.

https://toyotamanuals.com.au/docs/hilux-service-repair-manual-jul-15-current/N00148/manual/repair/contents/RM100000000LGZ5.html Page 4 of 9
 11/3/17, 10(31 pm

CHECK DTC (CHECK USING SYSTEM CHECK MODE SCREEN)

a. System check mode screen description

Screen Description
Display Content

· Device Name List No. 1

displays some of the
devices that make up
the audio and visual
system.
*a: Device name · The names of the
list No. 1 components from Device
Name List No. 1 are
shown in the following

https://toyotamanuals.com.au/docs/hilux-service-repair-manual-jul-15-current/N00148/manual/repair/contents/RM100000000LGZ5.html Page 5 of 9
 11/3/17, 10(31 pm

table.

Result codes for all devices are

*b: Check result
displayed.

· Present and history DTCs

and registered
connected device names
*c: Memory clear are cleared.
· Select "Memory CLR" for
3 seconds.

· A system check will be

performed again after
*d: Recheck the memory is cleared.
· "Recheck" will dim
during a system check.

· Device Name List No. 2

displays some of the
devices that make up
the audio and visual
*e: Device name system.
list No. 2 · The names of the
components from Device
Name List No. 2 are
shown in the following
table.

*a: Device Name List No. 1 Description

Connection
Name Component
Method
Radio and display
DA -
receiver assembly

*b: Check Result Description

Result Meaning Action
The device does
OK not respond with a -
DTC.
The device
Look up the DTC in
DETAIL responds with a
"Unit Check Mode".
DTC.

· Check
power
The device was supply wire
previously present, harness of
NCON* but does not the device.
respond in · Check the
diagnostic mode. AVC-LAN of
thedevice.

· Check
power
The device supply wire
responds in harness of
NRES* diagnostic mode, the device.
but gives no DTC · Check the
information. AVC-LAN of
thedevice.

*: As these functions are not equipped on the

https://toyotamanuals.com.au/docs/hilux-service-repair-manual-jul-15-current/N00148/manual/repair/contents/RM100000000LGZ5.html Page 6 of 9
 11/3/17, 10(31 pm

vehicle, they are not displayed.

*e: Device Name List No. 2 Description

Connection
Name Component
Method
No. 1 stereo jack Vehicle wire
AUX/VTR
adapter assembly harness

b. Unit check mode screen description

Screen Description
Display Content
*a: Device
Target device
name
*b: History Diagnostic memory results and
DTC stored DTCs are displayed.
*c: Current DTCs output in the service check
DTC are displayed.
*d: DTC DTC (Diagnostic Trouble Code)
The time and date of history DTCs
*e:
are displayed. (The year is
Timestamp
displayed in 2-digit format.)
Selecting "Code CLR" for 3 seconds
clears the diagnostic memory data
*f: Diagnosis
of the target device (both
clear switch
diagnostic system check result and
the displayed data are cleared).

HINT:
· This screen is updated once per second.
· A maximum of 6 DTCs can be displayed for history and present DTCs.

c. Read the system check result.

i. If the check result is "DETAIL", select the displayed check result to view the results on the "Unit Check Mode"
screen and record them.
NOTICE:
A maximum of 6 DTCs can be displayed for history and present DTCs on the "Unit Check Mode" screen.
Therefore, when 6 DTCs are displayed, troubleshoot those DTCs first and then check the "Unit Check Mode"
screen again to see if any other DTCs are displayed.

HINT:
· When all results are "OK", no DTCs are output.
· When proceeding to view the results of another device, press the "Back" switch to return to the
"System Check Mode" screen. Repeat the step above to view the results of other devices.

https://toyotamanuals.com.au/docs/hilux-service-repair-manual-jul-15-current/N00148/manual/repair/contents/RM100000000LGZ5.html Page 7 of 9
 11/3/17, 10(31 pm

ii. Check the details of the DTC(s).

Click hereAudio / Visual / Telematics>AUDIO /
VIDEO>AUDIO AND VISUAL SYSTEM(for Radio
and Display Type)>DIAGNOSTIC TROUBLE
CODE CHART

DTC CLEAR/RECHECK (CLEAR USING SYSTEM CHECK MODE SCREEN)

a. Clear DTCs
i. Select "Memory CLR" for 3 seconds.

ii. Confirm that the check results are cleared.

HINT:
· To clear the DTCs for a specific device,
clear the DTCs using the "Unit Check
Mode" screen.
· When clearing DTCs using the "Unit
Check Mode" screen, select "Code
CLR" for 3 seconds.

b. Recheck
i. Press the "Recheck" switch.

https://toyotamanuals.com.au/docs/hilux-service-repair-manual-jul-15-current/N00148/manual/repair/contents/RM100000000LGZ5.html Page 8 of 9
 11/3/17, 10(31 pm

ii. Confirm that all diagnostic codes are "OK" when

the check results are displayed. If a result other
than "OK" is displayed, perform troubleshooting
again.
HINT:
When the DTCs are cleared using the "Unit
Check Mode" screen, select "Back" to return
to the "System Check Mode" screen and
perform this operation.

FINISH DIAGNOSTIC MODE

a. Turn the ignition switch off.

https://toyotamanuals.com.au/docs/hilux-service-repair-manual-jul-15-current/N00148/manual/repair/contents/RM100000000LGZ5.html Page 9 of 9