LP156WHB

Liquid Crystal Display

Product Specification

SPECIFICATION
FOR
APPROVAL

( ◆ ) Preliminary Specification
( ) Final Specification

Title 15.6” HD TFT LCD

Customer Asus SUPPLIER LG Display Co., Ltd.

MODEL *MODEL LP156WHB

Suffix TLA1
*When you obtain standard approval,
please use the above model name without suffix

APPROVED BY SIGNATURE APPROVED BY SIGNATURE

J. S. Park / Manager
/
REVIEWED BY

/
S. W. Kim / Manager

/ PREPARED BY

K. T. Baek / Engineer
Y. C. Jung / Engineer

Please return 1 copy for your confirmation with Products Engineering Dept.
your signature and comments. LG Display Co., Ltd

Ver. 0.0 Jan. 06, 2014 1 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

Contents
RECORD OF REVISIONS…………………………………………………………………… 3

1. GENERAL DESCRIPTION……………………………………………………………… 4

2. ABSOLUTE MAXIMUM RATINGS……………………………………………………... 5

3. ELECTRICAL SPECIFICATIONS………………………………………….…………… 6
3-1. LCD ELECTRICAL CHARACTREISTICS…..…………………………………………..... 6
3-2. LED BACKLIGHT ELECTRICAL CHARACTREISTICS………………………………..... 6
3-3. INTERFACE CONNECTIONS……………………………………………………………… 8
3-4. LVDS SIGNAL TIMING SPECIFICATION………………………………………………… 9
3-5. SIGNAL TIMING SPECIFICATIONS………………………………………………………. 11
3-6. SIGNAL TIMING WAVEFORMS…………………………………………………………… 11
3-7. COLOR INPUT DATA REFERENCE……………………………………………………… 12
3-8. POWER SEQUENCE……………………………………………………………………….. 13

4. OPTICAL SPECIFICATIONS…………………………………………………………… 14

5. MECHANICAL CHARACTERISTICS…………………………………………………. 17

6. RELIABLITY……………………………………………………………………………… 20

7. INTERNATIONAL STANDARDS………………………………………………………. 21
7-1. SAFETY…………………………………………………………………..………………...… 21
7-2. ENVIRONMENT……………………………………………………………..…………...…. 21

8. PACKING………………………………………………………………………...……….. 22
8-1. DESIGNATION OF LOT MARK………………………………………………….………… 22
8-2. PACKING FORM…………………………………………………………………..………… 22

9. PRECAUTIONS…………………………………………………………………………… 23

APPENDIX A. LGD PROPOSAL FOR SYSTEM COVER DESIGN………………...……………..……. 25

APPENDIX B. ENHANCED EXTENDED DISPLAY IDENTIFICAION DATA….…………………….….. 30

Ver. 0.0 Jan. 06, 2014 2 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

Record of Revisions

EDID
Revision No Revision Date Page Description
version
0.0 Jan. 06. 2014 All First Draft (Preliminary Specification) 0.0

Ver. 0.0 Jan. 06, 2014 3 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

1. General Description
The LP156WHB is a Color Active Matrix Liquid Crystal Display with an integral LED backlight system. The
matrix employs a-Si Thin Film Transistor as the active element. It is a transmissive type display operating in
the normally white mode. This TFT-LCD has 15.6 inches diagonally measured active display area with HD
resolution (1366 horizontal by 768 vertical pixel array). Each pixel is divided into Red, Green and Blue sub-
pixels or dots which are arranged in vertical stripes. Gray scale or the brightness of the sub-pixel color is
determined with a 6-bit gray scale signal for each dot, thus, presenting a palette of more than 262,144
colors. The LP156WHB has been designed to apply the interface method that enables low power, high
speed, low EMI. The LP156WHB is intended to support applications where thin thickness, low power are
critical factors and graphic displays are important. In combination with the vertical arrangement of the sub-
pixels, the LP156WHB characteristics provide an excellent flat display for office automation products such
as Notebook PC.

I2C EEPROM 1 1366

for EDID & T-Con

I2C TFT-LCD Panel

User connector

LVDS Timing
Data Signal (1366 x RGB x 768)
Controller
768
Gate
DVCC
Signal
40 DVCC, AVDD ,Vcom,
VCC Source Driver
Pin

Power Block Gamma, Gate Signal

VLED VOUT_LED
LED_EN
LED Driver LED Cathode LED Backlight
PWM

General Features
Active Screen Size 15.6 inches diagonal
Outline Dimension 359.5(H, Typ.) × 217.2(V, Typ.) × 3.80(D, Max.) [mm] (with PCBA)
Pixel Pitch 0.252 mm X 0.252 mm
Pixel Format 1366 horiz. by 768 vert. Pixels RGB strip arrangement
Color Depth 6-bit, 262,144 colors
Luminance, White 200 cd/m2(Typ.)
Power Consumption Total 2.8W (Typ.) Logic : 0.7W (Typ. @ Mosaic), B/L : 2.1W (Typ.)
Weight 400g (Max.)
Display Operating Mode Normally white
Surface Treatment Glare treatment (3H) of the front Polarizer
RoHS Compliance Yes
BFR / PVC / As Free Yes for all

Ver. 0.0 Jan. 06, 2014 4 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

2. Absolute Maximum Ratings

The following are maximum values which, if exceeded, may cause faulty operation or damage to the unit.

Table 1. ABSOLUTE MAXIMUM RATINGS

Values
Parameter Symbol Units Notes
Min Max
Power Input Voltage VCC -0.3 4.0 VDC at 25  2C

Operating Temperature TOP 0 50 C 1

Storage Temperature HST -20 60 C 1

Operating Ambient Humidity HOP 10 90 %RH 1

Storage Humidity HST 10 90 %RH 1

Note : 1. Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39C Max, and no condensation of water.
Note : 2. Storage Condition is guaranteed under packing condition.
90% 80%

60 60%

Wet Bulb 50
Humidity[(%)RH]

Temperature [℃] Storage

40 40%

30 Operation
20
20%
10
0
10%

-20 0 10 20 30 40 50 60 70 80

Dry Bulb Temperature [℃]

Ver. 0.0 Jan. 06, 2014 5 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

3. Electrical Specifications
3-1. LCD Electrical Characteristics

Table 2. LCD ELECTRICAL CHARACTERISTICS

Values
Parameter Symbol Unit Notes
Min Typ Max
Power Supply Input Voltage VCC 3.0 3.3 3.6 V 1
Permissive Power Supply Input Ripple VCCrp - - 100 mVp-p
Power Supply Input Current Mosaic ICC - 220 255 mA
2
Power Consumption PCC - 0.7 0.8 W
Power Supply Inrush Current ICC_P - - 1.5 A 3
Differential Impedance ZLVDS 90 100 110 Ω

Note)
1. The measuring position is the connector of LCM and the test conditions are under 25℃, fv = 60Hz
2. The specified ICC current and power consumption are under the VCC = 3.3V , 25℃, fv = 60Hz condition
and Mosaic pattern.

3. The VCC rising time is same as the minimum of T1 at Power on sequence.

3.3V
Rising time
VCC 90%

0V 10%
0.5ms

Ver. 0.0 Jan. 06, 2014 6 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

3-2. LED Backlight Electrical Characteristics

Table 3. LED B/L ELECTRICAL CHARACTERISTICS

Values
Parameter Symbol Unit Notes
Min Typ Max
LED Power Input Voltage VLED 7.0 12.0 21.0 V 1
LED Power Input Current ILED - 175 193 mA
2
LED Power Consumption PLED - 2.1 2.3 W
LED Power Inrush Current ILED_P - - 1.5 A 3
PWM Duty Ratio 5 - 100 % 4
PWM Jitter 0 - 0.2 % 5
PWM Frequency FPWM 200 - 1000 Hz 6
High Level Voltage VPWM_H 2.5 - 3.6 V
PWM
Low Level Voltage VPWM_L 0 - 0.3 V
High Voltage VLED_EN_H 2.5 - 3.6 V
LED_EN
Low Voltage VLED_EN_L 0 - 0.3 V
Life Time 12,000 - - Hrs 7

Note)
1. The measuring position is the connector of LCM and the test conditions are under 25℃.
2. The current and power consumption with LED Driver are under the VLED = 12.0V , 25℃, PWM Duty 100%
and White pattern with the normal frame frequency operated(60Hz).
3. The VLED rising time is same as the minimum of T13 at Power on sequence.
12.0V
Rising time 90%
VLED

0V 10%
0.5ms
4. The operation of LED Driver below minimum dimming ratio may cause flickering or reliability issue.
5. If Jitter of PWM is bigger than maximum, it may induce flickering.
6. This Spec. is not effective at 100% dimming ratio as an exception because it has DC level equivalent to 0Hz.
In spite of acceptable range as defined, the PWM Frequency should be fixed and stable for more consistent
brightness control at any specific level desired.
7. The life time is determined as the time at which brightness of LCD is 50% compare to that of minimum
value specified in table 7. under general user condition.

Ver. 0.0 Jan. 06, 2014 7 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

3-3. Interface Connections

Table 4. MODULE CONNECTOR PIN CONFIGURATION (CN1)
Pin Symbol Description Notes
1 NC No Connection
2 VCC LCD Logic and driver power (3.3V Typical)
3 VCC LCD Logic and driver power (3.3V Typical)
4 V EDID DDC power (3.3V)
5 NC No Connection
6 CLK EDID DDC clock
7 DATA EDID DDC data
8 X0- Negative LVDS differential data input for pixel
9 X0+ Positive LVDS differential data input for pixel
10 GND High speed ground
11 X1- Negative LVDS differential data input for pixel
12 X1+ Positive LVDS differential data input for pixel [Connector]
13 GND High speed ground LSM, GT05Q-40S-H10
14 X2- Negative LVDS differential data input for pixel or equivalent
15 X2+ Positive LVDS differential data input for pixel
16 GND High speed ground
17 XC- Negative LVDS differential clock input for pixel
[Connector pin arrangement]
18 XC+ Positive LVDS differential clock input for pixel
Pin 40 Pin 1
19 GND High speed ground
20 NC No Connection
21 NC No Connection
22 GND High Speed Ground
23 NC No Connection
24 NC No Connection
25 GND High Speed Ground
26 NC No Connection
27 NC No Connection [EDID & LGD P-Vcom Share pin]
28 GND High Speed Ground 1. Pin for EDID & P-Vcom : #6, #7
29 NC No Connection 2. P-Vcom Address : 0101000x
30 NC No Connection
31 BL_GND LED Backlight ground
32 BL_GND LED Backlight ground
33 BL_GND LED Backlight ground
34 NC No Connection
35 BL PWM System PWM signal input for dimming
36 BL ENABLE LED Backlight on/off control
37 NC No Connection
38 VLED LED Backlight power (12V Typical)
39 VLED LED Backlight power (12V Typical)
40 VLED LED Backlight power (12V Typical)

Ver. 0.0 Jan. 06, 2014 8 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

3-3. LVDS Signal Timing Specifications

3-3-1. DC Specification
LVDS -
VDD=1.8V
|VID|

LVDS +

VCM VIN_MAX VIN_MIN

# |VID| = |(LVDS+) – (LVDS-)|
# VCM = {(LVDS+) + (LVDS-)}/2
0V

Description Symbol Min Typ Max Unit Notes

LVDS Differential Voltage |VID| 100 - 600 mV -
LVDS Common mode Voltage VCM |VID| /2 1.2 VDD- |VID|/2 V -
LVDS Input Voltage Range VIN 0.3 - VDD V -

3-3-2. AC Specification
Tclk

LVDS Clock

LVDS Data

tSKEW (Fclk = 1/Tclk)

1) 85MHz > Fclk ≥ 65MHz : -400 ~ +400
tSKEW 2) 65MHz > Fclk ≥ 25MHz : -600 ~ +600

Description Symbol Min Max Unit Notes

85MHz > Fclk ≥
tSKEW - 400 + 400 ps
65MHz
LVDS Clock to Data Skew Margin
65MHz > Fclk ≥
tSKEW - 600 + 600 ps
25MHz
LVDS Clock to Clock Skew Margin (Even
tSKEW_EO - 1/7 + 1/7 Tclk -
to Odd)
Maximum deviation
FDEV - ±3 % -
of input clock frequency during SSC
Maximum modulation frequency
FMOD - 200 KHz -
of input clock during SSC

Ver. 0.0 Jan. 06, 2014 9 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

tSKEW_EO

LVDS Odd Clock

Tclk

LVDS Even Clock

Tclk

LVDS Even Data

< Clock skew margin between channel >

Freq.

Fmax
Fcenter * FDEV
Fcenter

Fmin

1
FMOD

Time

< Spread Spectrum >

3-3-3. Data Format
1) LVDS 1 Port

Tclk

Tclk *4/7 Tclk *3/7

RCLK+
Tclk *1/7

R3 R2 R1 R0 G0 G5 R4 R3 R2 R1 R0 G0 R5 R4 MSB R5
RA+/-
R4
R3
RB+/- G4 G3 G2 G1 B1 B0 G5 G4 G3 G2 G1 B1 B0 G5
R2
R1
RC+/- B5 B4 B3 B2 DE VSYNC HSYNC B5 B4 B3 B2 DE VSYNC HSYNC LSB R0

Previous (N-1)th Cycle Current (N)th Cycle Next (N+1)th Cycle

< LVDS Data Format >

Ver. 0.0 Jan. 06, 2014 10 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

3-4. Signal Timing Specifications

This is the signal timing required at the input of the User connector. All of the interface signal timing should be
satisfied with the following specifications and specifications of LVDS Tx/Rx for its proper operation.
Table 4. TIMING TABLE
ITEM Symbol Min Typ Max Unit Note
DCLK Frequency fCLK - 76.32 - MHz
Period tHP 1594 1610 1626
Hsync Width tWH 24 32 40 tCLK
Width-Active tWHA 1366
Period tVP 787 790 793
Vsync Width tWV 4 5 6 tHP
Width-Active tWVA 768
Horizontal back porch tHBP 160 164 168
tCLK
Data Horizontal front porch tHFP 44 48 52
Enable Vertical back porch tVBP 13 14 15
tHP
Vertical front porch tVFP 2 3 4
Notice. all reliabilities are specified for timing specification based on refresh rate of 60Hz. However,
LP156WHB has a good actual performance even at lower refresh rate (e.g. 40Hz or 50Hz) for power saving
Mode, whereas LP156WHB is secured only for function under lower refresh rate. 60Hz at Normal mode, 50Hz,
40Hz at Power save mode. Don’t care Flicker level (Power save mode).

3-5. Signal Timing Waveforms

Condition : VCC =3.3V
High: 0.7VCC
Data Enable, Hsync, Vsync
Low: 0.3VCC

tCLK 0.5 Vcc

DCLK

tHP
Hsync tWH
tHBP tWHA tHFP

Data Enable
tVP
tWV
Vsync tVBP tWVA tVFP

Data Enable

Ver. 0.0 Jan. 06, 2014 11 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

3-6. Color Input Data Reference

The brightness of each primary color (red, green and blue) is based on the 6-bit gray scale data input for the
color ; the higher the binary input, the brighter the color. The table below provides a reference for color
versus data input.

Table 5. COLOR DATA REFERENCE

Input Color Data
RED GREEN BLUE
Color
MSB LSB MSB LSB MSB LSB
R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0

Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Red 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0

Green 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0

Basic Blue 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1
Color Cyan 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1

Magenta 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1

Yellow 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0

White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

RED (00) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

RED (01) 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0

RED … … … …

RED (62) 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0

RED (63) 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0

GREEN (00) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

GREEN (01) 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0

GREEN ... … … …

GREEN (62) 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0

GREEN (63) 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0

BLUE (00) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

BLUE (01) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1

BLUE … … … …

BLUE (62) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0

BLUE (63) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1

Ver. 0.0 Jan. 06, 2014 12 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

3-7. Power Sequence

90% 90%
Power Supply Input
VCC
0V 10% 10%

T3 T7 T4
T1 T2 Valid Data
Interface Signal, Vi
LVDS
0V

LED BL T5 3.0V 3.0V T6

On/Off Control Signal
LED_EN 0V (Off)

T9 T10

LED BL
Dimming Control Signal
PWM 0V (Low) Valid Data

T8 T11

LED Driver Input Voltage 90% 90%

VLED
0V 10% T12 T13 10%

Table 6. POWER SEQUENCE TABLE

Value Value
Symbol Units Symbol Units
Min Typ Max Min Typ Max
T1 0.5 - 10 ms T8 10 - - ms
T2 0 - 50 ms T9 0 - - ms
T3 0 - 50 ms T10 0 - - ms
T4 500 - - ms T11 10 - - ms
T5 200 - - ms T12 0.5 - 10 ms
T6 200 - - ms T13 0.5 - 10 ms
T7 0.5 - 10 ms

Note)
1. Do not insert the mating cable when system turn on.
2. Valid Data have to meet “3-3. LVDS Signal Timing Specifications”
3. LVDS, LED_EN and PWM need to be on pull-down condition on invalid status.
4. LGD recommend the rising sequence of VLED after the Vcc and valid status of LVDS turn on.

Ver. 0.0 Jan. 06, 2014 13 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

4. Optical Specification
Optical characteristics are determined after the unit has been ‘ON’ and stable for approximately 20 minutes in
a dark environment at 25C. The values specified are at an approximate distance 50cm from the LCD surface
at a viewing angle of  and  equal to 0.
FIG. 1 presents additional information concerning the measurement equipment and method.

FIG. 1 Optical Characteristic Measurement Equipment and Method

LCD Module Equipment

Optical Stage(x,y)

500mm±50mm

Table 7. OPTICAL CHARACTERISTICS

Ta=25C, VCC=3.3V, fV=60Hz

Values
Parameter Symbol Units Notes
Min Typ Max
Contrast Ratio CR 400 500 - 1
Surface Luminance, white LWH 170 200 - cd/m2 2
 WHITE (5P) - 1.2 1.4
Luminance Variation - 3
 WHITE(13P) - 1.4 1.6
Response Time Tr + Tf - 16 25 ms 4
Rx 0.578
RED
Ry 0.344
Gx 0.337
Color GREEN
Gy Typical 0.571 Typical
Coordinates
Bx - 0.03 0.159 + 0.03
BLUE
By 0.12
Wx 0.313
WHITE
Wy 0.329
x axis, right(=0) r 40 - -
Viewing Angle x axis, left (=180) l 40 - - 5
Degree
y axis, up (=90) u 10 - -
y axis, down (=270) d 30 - -
Gray Scale 6

Ver. 0.0 Jan. 06, 2014 14 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

Note)
1. It should be measured in the center of screen(1 Point). Contrast Ratio(CR) is defined mathematically as

Surface Luminance with all white pixels

Contrast Ratio(1 Point) =
Surface Luminance with all black pixels

2. Surface luminance is the average of 5 point across the LCD surface 50cm from the surface with
all pixels displaying white. For more information see FIG 2.

LWH = Average(1,2, … 5 Point)

3. The variation in surface luminance , The panel total variation ( WHITE) is determined by measuring N
at each test position 1 through 13 and then defined as following numerical formula.
For more information see FIG 2.

Maximum (1,2, … 5 Point) Maximum (1,2, … 13 Point)

 WHITE (5P) =  WHITE (13P) =
Minimum (1,2, … 5 Point) Minimum (1,2, … 13 Point)

4. Response time is the time required for the display to transition from white to black (rise time, Tr) and
from black to white (falling time, Tf). For additional information see FIG 3.

5. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined
for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the
LCD surface. For more information see FIG 4.

6. Gray scale specification

Gray Level Luminance [%] (Typ)

L0 TBD
L7 TBD
L15 TBD
L23 TBD
L31 TBD
L39 TBD
L47 TBD
L55 TBD
L63 100

Ver. 0.0 Jan. 06, 2014 15 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

FIG. 2 Luminance
<Measuring point for Average Luminance & measuring point for Luminance variation>
H

10mm A

6 7 8 10mm
2 3
B H,V : ACTIVE AREA
V A : H/4 mm
9 1 10
B : V/4 mm
POINTS: 13 POINTS
4 5 13
11 12

FIG. 3 Response Time Active Area

The response time is defined as the following figure and shall be measured by switching the input signal
for “black” and “white”.
Tr Tf
%
100
90

Optical
Response
10
0 white white
black

FIG. 4 Viewing angle Normal

Eye Y
<Dimension of viewing angle range>  = 90 , Up

 = 180 ,
Left 

 = 0 ,
Right

 = 270 ,
Down

Ver. 0.0 Jan. 06, 2014 16 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

5. Mechanical Characteristics
The contents provide general mechanical characteristics for the model LP156WHB. In addition the figures
in the next page are detailed mechanical drawing of the LCD.

Horizontal 359.5  0.5 mm

Outline Dimension Vertical 217.2  0.5 mm (with PCBA)

Thickness 3.8 mm (max)

Horizontal 347.5  0.5 mm

Bezel Area
Vertical 196.8  0.5 mm

Horizontal 344.23 mm
Active Display Area
Vertical 193.54 mm

Weight 400g (Max.)

Surface Treatment Hard Coating(3H), Glare treatment of the front polarizer

Ver. 0.0 Jan. 06, 2014 17 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

<FRONT VIEW>

Ver. 0.0 Jan. 06, 2014 18 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

<REAR VIEW> Note) Unit:[mm], General tolerance:  0.5mm

Ver. 0.0 Jan. 06, 2014 19 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

6. Reliability

Environment test condition

No. Test Item Conditions

1 High temperature storage test Ta= 60C, 240h
2 Low temperature storage test Ta= -20C, 240h
3 High temperature operation test Ta= 50C, 50%RH, 240h
4 Low temperature operation test Ta= 0C, 240h
5 Vibration test (non-operating) Random, 1.0Grms, 10 ~ 300Hz(PSD 0.0035)
3 axis, 30min/axis
6 Shock test (non-operating) - No functional or cosmetic defects following a shock
to all 6 sides delivering at least 180 G in a half sine
pulse no longer than 2 ms to the display module
- No functional defects following a shock delivering
at least 200 g in a half sine pulse no longer than 2
ms to each of 6 sides. Each of the 6 sides will be
shock tested with one each display, for a total of 6
displays
7 Altitude operating 0 ~ 10,000 feet (3,048m) 24Hr
storage / shipment 0 ~ 40,000 feet (12,192m) 24Hr

{ Result Evaluation Criteria }

There should be no change which might affect the practical display function when the display quality
test is conducted under normal operating condition.

Ver. 0.0 Jan. 06, 2014 20 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

7. International Standards
7-1. Safety
a) UL 60950-1, Underwriters Laboratories Inc.
Information Technology Equipment - Safety - Part 1 : General Requirements.
b) CAN/CSA-C22.2 No. 60950-1-07, Canadian Standards Association.
Information Technology Equipment - Safety - Part 1 : General Requirements.
c) EN 60950-1, European Committee for Electro technical Standardization (CENELEC).
Information Technology Equipment - Safety - Part 1 : General Requirements.
d) IEC 60950-1, The International Electro technical Commission (IEC).
Information Technology Equipment - Safety - Part 1 : General Requirements

7-2. Environment

a) RoHS, Directive 2011/65/EU of the European Parliament and of the council of 8 June 2011

Ver. 0.0 Jan. 06, 2014 21 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

8. Packing
8-1. Designation of Lot Mark
a) Lot Mark

A B C D E F G H I J K L M

A,B,C : SIZE(INCH) D : YEAR

E : MONTH F ~ M : SERIAL NO.

Note
1. YEAR

Year 2011 2012 2013 2014 2015 2016 2017 2018 2019 2020

Mark A B C D E F G H J K

2. MONTH

Month Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec

Mark 1 2 3 4 5 6 7 8 9 A B C

b) Location of Lot Mark

Serial No. is printed on the label. The label is attached to the backside of the LCD module.
This is subject to change without prior notice.

8-2. Packing Form

a) Package quantity in one box : 20 pcs

b) Box Size : 478 x 365 x 328

Ver. 0.0 Jan. 06, 2014 22 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

9. PRECAUTIONS

Please pay attention to the followings when you use this TFT LCD module.

9-1. MOUNTING PRECAUTIONS

(1) You must mount a module using holes arranged in four corners or four sides.
(2) You should consider the mounting structure so that uneven force (ex. Twisted stress) is not applied to the
module. And the case on which a module is mounted should have sufficient strength so that external
force is not transmitted directly to the module.
(3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer.
Transparent protective plate should have sufficient strength in order to the resist external force.
(4) You should adopt radiation structure to satisfy the temperature specification.
(5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former
generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit break
by electro-chemical reaction.
(6) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than HB
pencil lead. And please do not rub with dust clothes with chemical treatment.
Do not touch the surface of polarizer for bare hand or greasy cloth.(Some cosmetics are detrimental
to the polarizer.)
(7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like
chamois soaks with petroleum benzene. Normal-hexane is recommended for cleaning the adhesives
used to attach front / rear polarizers. Do not use acetone, toluene and alcohol because they cause
chemical damage to the polarizer.
(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes
deformations and color fading.
(9) Do not open the case because inside circuits do not have sufficient strength.
(10) When handling the LCD module, it needs to handle with care not to give mechanical stress to the PCB
and Mounting Hole area.”

9-2. OPERATING PRECAUTIONS

(1) The spike noise causes the mis-operation of circuits. It should be lower than following voltage :
V=± 200mV(Over and under shoot voltage)

(2) Response time depends on the temperature.(In lower temperature, it becomes longer.)
(3) Brightness depends on the temperature. (In lower temperature, it becomes lower.)
And in lower temperature, response time(required time that brightness is stable after turned on) becomes
longer.
(4) Be careful for condensation at sudden temperature change. Condensation makes damage to polarizer or
electrical contacted parts. And after fading condensation, smear or spot will occur.
(5) When fixed patterns are displayed for a long time, remnant image is likely to occur.
(6) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be
done by system manufacturers. Grounding and shielding methods may be important to minimized the
interference.

Ver. 0.0 Jan. 06, 2014 23 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

9-3. ELECTROSTATIC DISCHARGE CONTROL

Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that
treatment persons are connected to ground through wrist band etc. And don’t touch interface pin directly.

9-4. PRECAUTIONS FOR STRONG LIGHT EXPOSURE

Strong light exposure causes degradation of polarizer and color filter.

9-5. STORAGE
When storing modules as spares for a long time, the following precautions are necessary.

(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the
temperature between 5C and 35C at normal humidity.
(2) The polarizer surface should not come in contact with any other object.
It is recommended that they be stored in the container in which they were shipped.

9-6. HANDLING PRECAUTIONS FOR PROTECTION FILM

(1) When the protection film is peeled off, static electricity is generated between the film and polarizer.
This should be peeled off slowly and carefully by people who are electrically grounded and with well
ion-blown equipment or in such a condition, etc.
(2) The protection film is attached to the polarizer with a small amount of glue. If some stress is applied
to rub the protection film against the polarizer during the time you peel off the film, the glue is apt to
remain on the polarizer.
Please carefully peel off the protection film without rubbing it against the polarizer.
(3) When the module with protection film attached is stored for a long time, sometimes there remains a
very small amount of glue still on the polarizer after the protection film is peeled off.
(4) You can remove the glue easily. When the glue remains on the polarizer surface or its vestige is
recognized, please wipe them off with absorbent cotton waste or other soft material like chamois
soaked with normal-hexane.

9-7. THE LGD QA RESPONSIBILITY WILL BE AVOIDED IN CASE OF BELOW

(1) When the customer attaches TSM(Touch Sensor Module) on LCM without Supplier’s approval.
(2) When the customer attaches cover glass on LCM without Supplier’s approval.
(3) When the LCMs were repaired by 3rd party without Supplier’s approval.
(4) When the LCMs were treated like Disassemble and Rework by the Customer and/or Customer’s
representatives without supplier’s approval.

Ver. 0.0 Jan. 06, 2014 24 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

APPENDIX A. LGD Proposal for system cover design

1 Gap check for securing the enough gap between LCM and System back cover.

LCM a b

PAD
Back cover
Boss

◆ a : min 0mm
Boss ◆ b : min 0.3mm, Max 1.0mm

PAD

Back cover

1. Rear side of LCM is sensitive against external stress, and previous check
about interference is highly needed.
Define 2. In case there is something from system cover comes into the boundary
above, mechanical interference may cause the FOS defects.
(e.g.. Ripple, White spot..)

2 Check if antenna cable is sufficiently apart from T-CON of LCD Module.

T-CON T-CON

OK NG

Define If system antenna is overlapped with T-CON, It might be cause the noise

Ver. 0.0 Jan. 06, 2014 25 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

APPENDIX A. LGD Proposal for system cover design

3 Checking the path of the System wire

Wire

NG OK

1. If Wire path overlapped with LCM, it is happened white spot. COF problem, etc.
Define 2. OK  Wire path design to system side.
NG  Wire path overlapped with LCM.

4 Add pad to Prevent panel crack against external load (push)

Pad Back cover flange

LCM
boss
Boss PAD
Back cover

push push

Pad boss
boss boss
boss
crack
Back cover Back cover

OK NG

1. At flat type LCM, panel is easily cracked at flange area during push, assemble.
Define
2. Add pad, it prevent panel crack

Ver. 0.0 Jan. 06, 2014 26 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

APPENDIX A. LGD Proposal for system cover design

5 Check the rib or Bracket on back cover

LCM LCM

Back cover Back cover

Rib Bracket
OK OK

LCM LCM

Back cover Back cover

NG CO

1.It is necessary that the height of back cover rib or bracket is higher than LCM height. It can
prevent direct compression of panel at LCM edge.
Define
2.”ㄱ” shape bracket is stronger than “I” shape one.

6 Check the gap between front cover and LCM (glass)

a
Front cover

LCM

Back cover

[OK] a ≥ 0.3mm
[CO] 0.3mm ≥ a ≥ 0.1mm
[NG] a ≤ 0.1mm

Define Ripple can be happened by little gap between glass and front cover.

Ver. 0.0 Jan. 06, 2014 27 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

APPENDIX A. LGD Proposal for system cover design

7 Check the rib or Bracket on back cover

Light leakage
Front cover Front cover

LCM LCM

Back cover Back cover

OK NG

1.If it is possible, shrink to apply front cover of white color.

Define
2. White color can caused light leakage

8 Check the wire position(path)

Back cover

OK

Back cover

NG

1. It is necessary that wire is posited out of hook, not posited near hook,.
Define
2. If wire is posited near hook, it can be happened assemble error and panel crack during
assemble front cover

Ver. 0.0 Jan. 06, 2014 28 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

APPENDIX A. LGD Proposal for system cover design

9 Check mouse pad (touch pad) depth and shape of edge

a
[OK] a ≤ 0.3mm
[CO] 0.5mm ≥ a ≥ 0.3mm
[NG] a ≥ 0.5mm

Mouse pad

OK NG

1.Mouse pad step is deep, it is caused panel crack by external load.

Define
2. The edge shape must be smooth.

10 Check the step of keyboard area

Keyboard Keyboard

push push

crack

OK NG

Define The step of keyboard at the side edge of main body, it is caused panel crack

Ver. 0.0 Jan. 06, 2014 29 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

APPENDIX A. LGD Proposal for system cover design

11 Check the gap [PCB ~ system]

Panel
BLU

FPC Back cover

A

A’
a
a ≥ 0.5mm [at max dimension of design] Rib, Frame …
a ≥ 1.0mm [at typical dimension of
design]

1. Gap is too small, FPC is easily cracked by interference and repetitive bending.
Define (circuit is opened) .

2. Gap is must be kept more than 0.5mm(max dim.) and 1.0mm(typ dim.) .

12 System rib (on A cover)

External
shock

crack

OK NG
a

LCM a ≥ 0.5mm [at max dimension of design]

Rib a ≥ 1.0mm [at typical dimension of
design]
Back cover

1. Gap is too small and rib is too short, panel is easily cracked by external stress.

Define 2. Gap is must be kept more than 0.5mm(max dim.) and 1.0mm(typ dim.) .

3. The figure of rib is continuous or fully long.

Ver. 0.0 Jan. 06, 2014 30 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

APPENDIX B. Enhanced Extended Display Identification Data (EEDIDTM) 1/3

Ver. 0.0 Jan. 06, 2014 31 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

APPENDIX B. Enhanced Extended Display Identification Data (EEDIDTM) 2/3

Ver. 0.0 Jan. 06, 2014 32 / 30

 LP156WHB
Liquid Crystal Display
Product Specification

APPENDIX B. Enhanced Extended Display Identification Data (EEDIDTM) 3/3

Ver. 0.0 Jan. 06, 2014 33 / 30