PURPOSE : CORRECTION ISSUE NO.

: MSB-14EXL22_23-501 DATE : 2014-04-08

<DESTINATION/MODEL> <M/Y>
SUBJECT : TRANSFER POSITION DETECTION SWITCH SYSTEM (As per attached 1) 07-15
GROUP : MANUAL TRANSMISSION(22A) / AUTOMATIC TRANSMISSION(23A) PAJERO/MONTERO(V80/90)

1. Description :
Please refer to the attached document for the correction of the error in writing existing in the
applicable service manual. There are some errors in writing in the following DTCs.
・DTC No.32,33
・DTC No.C1454,C1455,C1456

2. Affected service manuals :

Please refer to the attached document (Attached sheet 1)

3. About the details :

Please refer to the attached document (Attached sheet 3-5)

MSB-14EXL22_23-501(14RV005) 1
 Attached sheet 1(1/2)
EU/RUSSIA
Applicable manual Pub. No. Applicable title (INFO ID) Contents
2008 PAJERO/MONTERO CBKE08E1-CD (Eng) Code No.32, 33: Transfer detection Attached
Workshop Manual CBKF08E1-CD (Fre) switch system (M221-10-540-04500-01) sheet 3
CBKG08E1-CD (Ger)
CBKS08E1-CD (Spa)
2009 PAJERO/MONTERO Code No.C1454, C1455, C1456: Transfer Attached
Workshop Manual Position Detection Switch System sheet 4
2009.5 PAJERO/MONTERO CBKE09E2-CD (Eng) (M221-10-760-01200-01)
Workshop Manual CBKF09E2-CD (Fre)
CBKG09E2-CD (Ger)
CBKS09E2-CD (Spa)
CBKI09E2-CD (Ita)
2010 PAJERO/MONTERO CBKE10E1-CD (Eng) Code No.C1454, C1455, C1456: Transfer Attached
Workshop Manual CBKF10E1-CD (Fre) Position Detection Switch System sheet 4
CBKG10E1-CD (Ger) (M221-10-760-07800-01)
CBKS10E1-CD (Spa)
CBKI10E1-CD (Ita)
2011 PAJERO/MONTERO CBKE11E1-CD (Eng)
Workshop Manual CBKF11E1-CD (Fre)
CBKG11E1-CD (Ger)
CBKS11E1-CD (Spa)
CBKI11E1-CD (Ita)
2012 PAJERO/MONTERO CBKE12E1-CD (Eng) Code No.C1454, C1455, C1456: Transfer Attached
Workshop Manual CBKF12E1-CD (Fre) Position Detection Switch System sheet 4
CBKG12E1-CD (Ger) (M221-10-760-07801-01)
CBKS12E1-CD (Spa)
CBKI12E1-CD (Ita)
2013 PAJERO/MONTERO CVWE13E1-CD (Eng)
Workshop Manual CVWF13E1-CD (Fre)
CVWG13E1-CD (Ger)
CVWS13E1-CD (Spa)
CVWI13E1-CD (Ita)
2015 PAJERO/MONTERO CVWE15E1-CD (Eng)
Workshop Manual CVWF15E1-CD (Fre)
CVWG15E1-CD (Ger)
CVWS15E1-CD (Spa)
CVWI15E1-CD (Ita)

EXP/GCC
Applicable manual Pub. No. Applicable title (INFO ID) Contents
2007 PAJERO/MONTERO PWJE0605R (Eng) Code No.32, 33: Transfer detection Attached
Workshop Manual PWJS0606R (Spa) switch system (M221-10-540-03400-01) sheet 3
2008 PAJERO/MONTERO PWJE0709R (Eng)
Workshop Manual PWJS0710R (Spa)
2009 PAJERO/MONTERO PWJE0812R (Eng) Code No.C1454, C1455, C1456: Transfer Attached
Workshop Manual PWJS0813R (Spa) Position Detection Switch System sheet 4
2010 PAJERO/MONTERO PWJE0908R (Eng) (M221-10-760-01200-01)
Workshop Manual PWJS0909R (Spa)

MSB-14EXL22_23-501(14RV005) 2
 Attached sheet 1(2/2)
MMAL/NZ
Applicable manual Pub. No. Applicable title (INFO ID) Contents
2007 PAJERO Workshop Manual MR936084 Code No.32, 33: Transfer detection switch Attached
2008 PAJERO Workshop Manual MR936455 system (M221-10-540-02300-01) sheet 3
NZ:DRAFT
2009 PAJERO Workshop Manual MR936637 Code No.C1454, C1455, C1456: Transfer Attached
NZ:DRAFT Position Detection Switch System sheet 4
(M221-10-760-02300-01)
2010 PAJERO Workshop Manual MR936976 Code No.C1454, C1455, C1456: Transfer Attached
NZ:DRAFT Position Detection Switch System sheet 4
(M221-10-760-08900-01)

CHINA
Applicable manual Pub. No. Applicable title (INFO ID) Content
2008 PAJERO Workshop Manual DRAFT Code No.32, 33: Transfer detection switch Attached
system (M231-11-590-06400-01) sheet 5

MSB-14EXL22_23-501(14RV005) 3
 MANUAL TRANSMISSION (FR) Attached sheet 3
TROUBLESHOOTING
<Incorrect>
STEP 9. Check the harnesses between each No.1 and earth at the wiring harness side. <Correct>
detection switch connectors C-08, C-09, C-12, C- OK: switch
13, C-14 terminal No.1 and transfer-ECU • When the transfer position is 2H, con-
connector D-123 terminals No.43, No.44, No.45, nector C-08 terminal No.1 resistance
No.46, No.47. should measure less than 2 Ω.
Check the output line for open circuit. When the transfer position is other
than 2H, connector C-08 terminal No.1
Q: Is the check result normal?
resistance should measure open cir-
YES : Go to Step 11.
cuit.
NO : Repair the wiring harness.
• When the transfer position is 2H or
4H, connector C-14 terminal No.1
STEP 10. Measure the resistance at each resistance should measure less than 2
detection switch connectors C-08, C-09, C-12, C- Ω.
13, C-14. When the transfer position is other
(1) Connect the M.U.T.-III to the diagnosis connector. than 2H or 4H, connector C-14 termi-
(2) Turn the ignition switch to the ON position. nal No.1 resistance should measure
(3) Transmission gear should be neutral position. open circuit.
(4) Item 2, 3: Shift actuator. • When the transfer position is 4H or
(5) Disconnect connectors C-08, C-09, C-12, C-13, 4HLc, connector C-13 terminal No.1
C-14, and measure the voltage between terminal resistance should measure less than 2
<Incorrect> Ω.
When the transfer position is other
resistance <Correct> than 4H or 4HLc, connector C-13 ter-
minal No.1 resistance should measure
open circuit.
• When the transfer position is 4HLc or
4LLc, connector C-12 terminal No.1
resistance should measure less than 2
Ω.
When the transfer position is other
than 4HLc or 4LLc, connector C-12
terminal No.1 resistance should meas-
ure open circuit.
• When the transfer position is 4LLc,
connector C-09 terminal No.1 resist-
ance should measure less than 2 Ω.
When the transfer position is other
than 4LLc, connector C-09 terminal
No.1 resistance should measure open
circuit.
Q: Is the check result normal?
YES : Go to Step 11.
NO : Replace the each detection switch (Refer to
GROUP 22B - Transmission ).

STEP 11. M.U.T.-III data list

Item 7: Transfer position (Refer to data list reference
table ).
Q: Is the check result normal?
YES : Intermittent malfunction (Refer to GROUP
00 − How to Cope with Intermittent
Malfunction ).
MSB-14EXL22_23-501(14RV005) 4 NO : Replace the transfer-ECU.
 MANUAL TRANSMISSION (FR) Attached sheet 4
TROUBLESHOOTING
<Incorrect>
STEP 9. Check the harnesses between each No.1 and earth at the wiring harness side. <Correct>
detection switch connectors C-08, C-09, C-12, OK: switch
C-13, C-14 terminal No.1 and transfer-ECU • When the transfer position is 2H, con-
connector D-123 terminals No.53, No.47, No.55, nector C-08 terminal No.1 resistance
No.54, No.46. should measure less than 2 Ω.
Check the output line for open circuit. When the transfer position is other
than 2H, connector C-08 terminal No.1
Q: Is the check result normal?
resistance should measure open cir-
YES : Go to Step 11.
cuit.
NO : Repair the wiring harness.
• When the transfer position is 2H or
4H, connector C-14 terminal No.1
STEP 10. Measure the resistance at each resistance should measure less than 2
detection switch connectors C-08, C-09, C-12, Ω.
C-13, C-14. When the transfer position is other
(1) Connect the M.U.T.-III to the diagnosis connector. than 2H or 4H, connector C-14 termi-
(2) Turn the ignition switch to the ON position. nal No.1 resistance should measure
(3) Transmission gear should be neutral position. open circuit.
(4) Item 2: Shift actuator. • When the transfer position is 4H or
(5) Disconnect connectors C-08, C-09, C-12, C-13, 4HLc, connector C-13 terminal No.1
C-14, and measure the voltage between terminal resistance should measure less than 2
<Incorrect> Ω.
When the transfer position is other
resistance <Correct> than 4H or 4HLc, connector C-13 ter-
minal No.1 resistance should measure
open circuit.
• When the transfer position is 4HLc or
4LLc, connector C-12 terminal No.1
resistance should measure less than 2
Ω.
When the transfer position is other
than 4HLc or 4LLc, connector C-12
terminal No.1 resistance should meas-
ure open circuit.
• When the transfer position is 4LLc,
connector C-09 terminal No.1 resist-
ance should measure less than 2 Ω.
When the transfer position is other
than 4LLc, connector C-09 terminal
No.1 resistance should measure open
circuit.
Q: Is the check result normal?
YES : Go to Step 11.
NO : Replace the each detection switch (Refer to
GROUP 22B - Transmission ).

STEP 11. M.U.T.-III data list

Item 40: Transfer position (Refer to data list refer-
ence table ).
Q: Is the check result normal?
YES : Intermittent malfunction (Refer to GROUP
00 − How to Cope with Intermittent
Malfunction ).
MSB-14EXL22_23-501(14RV005) 5 NO : Replace the transfer-ECU.
 AUTOMATIC TRANSMISSION Attached sheet 5
TROUBLESHOOTING <SS4II>

YES : Go to Step 11.

STEP 10. Measure the resistance at each
NO : Replace the each detection switch (Refer to
detection switch connectors C-08, C-09, C-12, C-
GROUP 23B - Transmission ).
13, C-14.
(1) Connect the M.U.T.-III to the diagnosis connector.
(2) Turn the ignition switch to the ON position. STEP 11. M.U.T.-III data list
(3) Transmission gear should be neutral position. Item 7: Transfer position (Refer to data list reference
(4) Item 2, 3: Shift actuator. <Correct> resistance table ).
(5) Disconnect connectors C-08, C-09, C-12, C-13,
<Incorrect> Q: Is the check result normal?
C-14, and measure the voltage between terminal YES : Intermittent malfunction (Refer to GROUP
No.1 and earth at the wiring harness side. 00 − How to Cope with Intermittent
<Incorrect> switch <Correct>
OK: Malfunction ).
• When the transfer position is 2H, con- NO : Replace the transfer-ECU.
nector C-08 terminal No.1 resistance
should measure less than 2 Ω.
When the transfer position is other
than 2H, connector C-08 terminal No.1
resistance should measure open cir-
cuit.
• When the transfer position is 2H or
4H, connector C-14 terminal No.1
resistance should measure less than 2
Ω.
When the transfer position is other
than 2H or 4H, connector C-14 termi-
nal No.1 resistance should measure
open circuit.
• When the transfer position is 4H or
4HLc, connector C-13 terminal No.1
resistance should measure less than 2
Ω.
When the transfer position is other
than 4H or 4HLc, connector C-13 ter-
minal No.1 resistance should measure
open circuit.
• When the transfer position is 4HLc or
4LLc, connector C-12 terminal No.1
resistance should measure less than 2
Ω.
When the transfer position is other
than 4HLc or 4LLc, connector C-12
terminal No.1 resistance should meas-
ure open circuit.
• When the transfer position is 4LLc,
connector C-09 terminal No.1 resist-
ance should measure less than 2 Ω.
When the transfer position is other
than 4LLc, connector C-09 terminal
No.1 resistance should measure open
circuit.
Q: Is the check result normal?

MSB-14EXL22_23-501(14RV005) 6