Objective Questions
Objective Questions
a) Fail the loco immediately b) Isolate the particular axle’s TM and work further
c) Clear the section and fail the loco d) Isolate the truck
18) In Medha Microprocessor version III loco Low hauling power will be
experienced when ( c
) a) TE limit switch is enabled. b) Rectifier fuse blown out
c) Both a & b. d) Power setter switch enabled.
21) In Medha microprocessor loco if TM No. 4 & 5 are isolated loco will start with ( b )
a )Series parallel combination b) Parallel combination
c)series parallel with shunt combination d)Parallel with shunt combination
32) In Medha Microprocessor loco if TM2 & 5 are isolated loco will start with ( a )
a) Series-parallel combination b) Parallel combination
c) Parallel with shunt combination d) Series-parallel with shunt
combination
33) Engine should not be cranked if it is shut down for more than ( c )
a) 24 hrs. b) 36 hrs. c) 48 hrs. d) 32 hrs.
34) If MCBG power breaker is in OFF position during cranking engine will ( b )
a) not Crank b) not Fire c) not Hold d) a and b
35) In WDG4 loco LLOB is located in ( a )
a) Accessories room b) Compressor room c) Engine power take off end d)ECC3
37) In WDP4/WDG4 loco if LLOB is in tripped position during cranking engine will ( d )
a) Crank b) Not Fire c) Not hold d) Not crank
39) In WDP4/WDG4 banker loco working CS, L/T switch should be kept in ( c )
a)Lead b)Trail c)HLPR d)Test
41) In WDP4/WDG4 dead loco for quick release of loco brakes open one side ( d )
a) MR equalizing cock b)BC equalizing cock
c)BP equalizing pipe d)Both a & b
43) In WDP4 /WDG4 loco before conducting air brake self test ( a )
a)Recycle MAB b)Recycle TCC1 and TCC2
c)Recycle Air drier breaker. d)Both a & b
54) In single BKT/Rev Loco during DB which power contactors will not pick up ?( d )
a)P2 & P22 b)S21 & S31 c)S1, S21 & S31 d)Both a and b
57) In GE governor loco during cranking if MUSD is in stop position engine will ( d )
a)Crank b)Not fire c)Not hold d)Not crank
58) In WW governor loco not provided with MUSDR relay during cranking if MUSD is in
STOP position during cranking engine will ( b )
a)Crank b)Not fire c)Not hold d)Not crank
73) "__________ is the main power supply of CCB for the CCB system." ( b )
a) DCU b)VCU c)PCU d)DVR
74) In WDG4 loco max. Brake cylinder pressure is ___Kg/Cm2 during backup system( a )
a)3.8 b)3.2 c)2.2 d)5
75) The EM2000 reads main reservoir air pressure from ______ transducer. ( d )
a)BPT b)BCT c)ERT d)MRPT
78) MR1 & MR2 are equipped bottom mounted automatic drain blow down valve. These are
used to remove condensate from the main reservoirs. The valves are normally air
actuated, and gets operated each time the __________________ ( a )
a)the compressor is unloading. b)When penalty brake applied c)the
compressor is loading. d)Micro Air breaker trips
79) After cranking, allow a minimum of __________minutes for starter motor cooling before
attempting another engine start. ( c )
a)20 b)10 c)2 d)5
80) Do not crank engine for more than _______ with starting motors in HHP ( d )
a) 30seconds b) 1minutes c) 10seconds d) 20 seconds
89) Maximum continuous speed of WDP4 class Loco motive is ____ kmph ( c )
a)140 b)150 c)160 d)180
106) _____ circuit breaker establishes local control with power from Locomotive battery or
Auxiliary generator to operate heavy duty switch gear, magnet valves, contactor, blower
and miscellaneous relays ( d )
a)AGFB b)MCB c)GF d) Local control
110) if the LR % is ________, EM2000 is reducing power output because the engine's
capabilities are less than the load being requested. ( b
) a)less than 200 b)less than 100 c)More than
100 d)less than 500
111) If the TM temperature is greater than _____°C the inverter will de-rate to keep the
traction motor temperature in control ( a )
a)200 b)100 c)95 d)92
112) LOCAL CONTROL circuit breaker establishes local (vs. train lined) control with power
from the locomotive battery or auxiliary generator to operate heavy duty switchgear,
magnet valves, contactors, blowers, and miscellaneous relays. ( a )
a)Relay b)Magnetic valves c)contactors d)All of the above
116) Shutting down of all diesel engines in a consist is accomplished ___ relay( c )
a)DMR b)GCR c)SDR d)FLR
117) Stepping down of 74 VDC input from the PRG 300 to +/- 15 VDC and distributes the
power to the PDPs (Power distribution panels) and the computer display screen is done
by ( d )
a)PSM 310 b)PSM 330 c)PSM 300 d)PSM 320
118) Stepping down of 74 VDC input from the PRG 300 to +5 VDC and distributes the power
to the computer chassis is done by ( c )
a)To step down ac to DC b)PSM 310 c)PSM 300 d)PSM 320
119) Stepping down of 74VDC from the PRG 300 to +/- 12 VDC and distributes the
power to the computer chassis is done by __ ( a
) a)PSM 310 b)PSM 330 c)PSM 300 d)PSM 320
124) The part of the ground relay system and connected to the companion alternator output,
as well as the AC input to FCF (Firing Control Feedback) module is protected by__( a )
a)AC control b) Companion Alternator output c)Fan circuits d)Radar
circuits
128) "Whenever DC link exceeds 3600volts, the ___ trips, which fires a hard crow bar ( b )
a) Hard Crowbar b)AC control TCC Break Over Diode (BOD)
c)Local control breaker d)GR
129) Whenever DC link voltage exceeds 3200 volts ,the TCC fires a _____crow bar ( c )
a)Hard Crowbar b)Sneaky crow bar c)Soft Crowbar d)GR
131) Which module converts analog input signals ( Pressure, Temperature, Voltage, Current,
Speed) into digital signals for the computer and converts digital computer output signals
into analog signals. ( c )
a)DIO b)FCF c)ADA d)FCD
132) In WDM2 locomotives, during cranking, if Normally Closed Interlock of SAR is not
getting closed , the result will be _______ ( c )
a)Throttle will not respond b)Load meter will not respond
c)Engine will crank and fire but not hold d)Engine will not fire
134) Fuel pump motor is not working though the all circuit breakers are switched ON, the
immediate reason could be_________ ( d )
a)ERF not closed b)R1 and R2 not picked up
c)GFC not picked up d)FPC not picked up
135) What is the Fuel oil tank capacity in WDP4D locomotive in litres. ( b )
a)6000 b)5000 c)3000 d)5500
138) What is the maximum permissible speed of ( designed for ) WDG4 locomotives ( b )
a)150 kmph b) 120 kmph c) 100 kmph d) 75 kmph
143) Pre lubrication is required if an engine that has been shut down for
more than--- hours ( a
) a) 48 b)24 c)12 d)8
144) The purpose of Turbo lube pump in WDP4 Locomotive before cranking is ( c )
a) To lubricate the Turbo b)To remove the residual heatc)To lubricate turbo bearing
d)To lubricate crank shaft
145) Turbo lube pump should be running for ____minutes after engine is shutdown if engine
was running at 5th notch and higher for 60minutes prior to engine shut down.( b )
a)15 b)35 c)20 d)45
146) What is the Safety Device provided in the Lube oil system ? ( c )
a) GFOLR b) OSTA c) LLOB d)LWS
149) From where the control air pressure will get air pressure ( b )
a)MR2 b)MR1 c)BKTs d)J filter
150) Main Reservoir (compressed air pressure) Unloading will takes place at_kg /cm2 ( c )
a)8 b)9 c)10 d)11
155) Manual Sanding is cutout when the locomotive is operating in power/wheel creep mode,
and moving at speeds above ( c )
a)30kmph b)10kmph c)19.5 km/h d)15kmph
159) The EM2000 will consider a temperature probe failed if it reads ________ ( b )
a)less than -155° C or greater than 150° C b)less than -55° C or greater than
150°C c)more than -55° C or greater than 150° C d)less than -55° C or greater than
250° C
160) In HHP loco the system maintains the coolant temperature within a predetermined range
from ( a )
a)79° C to 85° C b) 85 to 95° C c) 92 to 100 ° C d) 72 to 80 ° C
162) Hot engine alarm ( HEA) will come at _____°Cin WDG3A locos ( c )
a) 60 b) 70 c) 90 d) 80
163) During one of the following occasions Hot engine alarm indication will get ( c )
a) Continuous 8th notch working b) Excess load
c) Water pump not working d) Full water in expansion tank
168) Whenever stopped on gradient for any reason it is essential to apply the
______ brakes ( c )a)
SA.9 b) A.9 c) A9 & SA9 d) Hand brake
169) How much pressure should be ensured in the engine and BV before staring
air brake train ? ( c
) a) 6cm2kg,4.9 kg/cm2 b) 5.2kg/cm2, 4.7 kg/cm2
c) 5kgcm2, 4.8 kg/cm2 d) 4.8kg/cm2, 5kg/cm2
170) For any reason, a train is brought to a stand, the hand brakes of Locomotive
and formation shall be applied if stoppage is more than ( d
) a) 5 minutes b) 10 minutes c) 20 minutes d) 15 minutes
172) The following shall not be used for extinguishing fires on electrical equipment. ( c )
a) Dry chemical powder b) foam c) water d)none of these
174) What combination of trains are Permitted for running long haul train? ( d )
a)Empty/Empty b)loaded/Empty c)Loaded/Loaded d)All
the above
176) What precaution should be taken for conducting Air brake self test in GM locos? ( d )
a) Secure loco
b)Secure formation
c)Detach loco and secure
d)Secure both, close BP & FP COC of loco towards formation.
177) What should be done first for changing console in WDG 4 / WDP 4 locos ? ( a )
a)Disable working control stand & enable non working control stand
b)Enable working control stand & disable non working control stand
c)As per convenience
d)None of the above
178) When Head light become defective speed of the train shall not exceed ____.( c )
a) 20Kmph b) 30Kmph c) 40kmph d) 50kmph
179) While takin over charge of Loco, if Flasher light glows but does not flash/blink, what
action would you take? ( a )
a) Fail the loco b) Will work to nearest shed
c) Inform PRC & work further. d) Work normally
180) During engine starting if engine is cranking, Firing, Over speeding, OSTA Tripping
and Engine shutting down the reason may be ( b
) a)Main Generator failure b) Taco Generator failure
c)Exciter Generator failure d) Auxiliary Generator failure
182) While working LE's Loco Pilot should _______ to Stop the Locomotive. ( b )
a) apply A-9 brake b) apply SA-9 and Dynamic Brakes c) apply Hand brakes
d) close the throttle to zero.
183) Locos provided with Cast Iron brake blocks requires ______than the Locos provided with
Composite brake blocks ( a )
a)More braking distance b)Less braking distance c)frequent change of
brake blocks d)BC pressure 3.8 kg/cm2
184) If train stopped in mid section on account of Loco Failure Loco pilot should do
____________immediately ( b )
a)Inform TLC/PCOR b)Put on Flasher Light, Apply A-9,SA-9, wooden wedges
and secure formation. c)Ask for relief Loco d)Attend the Locomotive
187) While TOC of Loco, If Flasher light glows but does no blink, what action would
you take. ( a )
a) Fail the loco b)Will work to nearest shed c)Change the bulb d)Work normally
188) After which check/restriction, non derailed vehicles of a train involved in accident be
allowed for on-ward journey ( b )
a) Without check b) After certified by TXR c)With 10% less speed d)80
KMPH
189) What immediate action would you take on noticing sudden drop of BPpressure/vacuum
on run ? ( c )
190) When Head light becomes defective speed of the train shall not exceed ? ( c )
a) 20 kmph b) 30 kmph c) 40 kmph d) 50 kmph
191) What should be done by LP for releasing proportional loco brakes during
A9 application ? ( c
) a) Pressing BKIV foot pedal b) Application of DB c) Either A or B
d) None
196) If battery ammeter is showing over charging, what may be the reason? ( c )
a) BS open b) MB1 tripped c) Battery defective d) AGFB tripped
197) If BA shows over charging due to defective battery, the following action is to
be taken? ( a
)
a) BS to be open b) Shut down the engine
c) Engine to be brought to idle d) No action required
198) If battery ammeter shows over charging, what may be the reason? ( c )
a) BS open b) MB1 tripped c) VRP defective d) AGFB tripped
199) If BA shows over charging due to defective VRP, the following action is to
be taken? ( a
) a) AGFB off b) Shutdown the Engine c) Idle d) No action required
203) If Battery ammeter shows discharging and not rectified what is the action to ( d )
be taken?
a) Work for 4 Hours b) Do not Shut down c) Do not allow for
Automatic Shut Down. d)All of the above
204) What is the reason for battery ammeter showing ZERO? ( a )
a) Battery Switch Open b) AGFB Tripped c) VRP Defective
d) AUX. GEN. Defective
207) If engine is not cranking which switch is to be checked on the front panel? ( c )
a) Battery Switch b) MUSD c) ECS d) GF Switch
209) If engine is not cranking which power contactor interlocks are to be checked?( a)
a) P22, S1 b) P22, S21 c) P21, S1 d) P1, S1
210) For engine cranking what should be MUSD & ECS position? ( b )
a) RUN, RUN b) RUN, IDLEc) STOP, RUN d) STOP,IDLE
211) If FPC Contactor closing but engine is not cranking what may be the reason?( c )
a) MB1 Tripped/Off b) MB2 Tripped/Off c) FPB Tripped/Off
d) MFPB1 & MFPB2 Tripped/Off
212) If engine is cranking but not firing what may be the reason? ( d )
a) OPS1 Stuck up b) LWS Operated c) OSTA Tripped d) All the above
213) If engine is cranking but not firing with indication what may be the reason?( a )
a) LWS Operated b) OSTA Tripped c) SAR Defective d) All the above
214) If engine is cranking but not firing while starting what may be the reason? ( d )
a) FPM not working b) Fuel Booster Pump defective c) Love joy coupling
defective d) All the above
216) What is the reason if engine is cranking, firing but not holding? ( d )
a) SAR Interlock defective b) OPS Defective c) Lube oil system defective (Below
1.6Kg/Cm d) All the above
221) What is the reason if engine shutdown without any indication on run
in GE Governor? ( a
) a) Tacho Generator failure b) LWS c) OPS d)
LLOB
222) What happens if Amphenol plug is slack on GE governor loco? ( b )
a) Not cranking b) Not Firing c) Not Holding d) No Problem
230)To reset only Buzzer what is the action required by the Driver? ( c )
a) SW1 &SW2 b) SP1 &SP2 c) Switch On normal flasher light and
SW1&SW2 Off d) All the above
240) If engine is running with Hot engine alarm which safety device is operated?( c )
a) LWS b) OPS c) ETS d) SAR
245) In AC/DC Locos during cranking which relay protects Auxiliary And
Exciter Generators? ( c
) a) SAR b) GR c) TDR d) WSR
246) In place of AC Governor, which Governor is provided for compressor loading and
unloading ( a )
a) EPG b) GE c) Z.W d) Run-Release
247) What is the purpose of GFOLR in AC/DC Locomotive? ( c )
a) To protect Main Generator field b) To protect Rectifier panel
c) To protect Main Generator field & rectifier panel d) To protect Auxiliary
Generator
249) which circuits are protected by GR1 & GR2 after ear thing? ( c )
a) Power Circuit b) Control circuit c) Power and Control circuits
d) Nothing
250) what are the changes in single BKT Locomotives as compare to Double
BKT Loco’s? ( d )
254) If BKT or Reverser is not operating properly what is the action to be taken?( b )
a) Fail the loco b) Operate manually with `L’ rod c) Shutdown engine
d) Engine Idle
a) 3.5 b) 5 c) 6 d) 8
a)12 b) 24 c) 36 d) 16
268) Pinion to Bull gear ratio in WDM3A loco is ________ ( b )
a)18:74 b) 18:65 c) 17:77 d) 17:90
269) In WDM3A loco FTTM is driven with ________ ( b )
a)Belts b) Gear c) Hydraulic pressure d) Electric motor
270) In WDM3A loco RTTM is driven with ________ ( a )
a)Belts b) Gear c) Hydraulic pressure d) Electric motor
271) Type of transmission in WDM3A loco ( b )
a)DC-AC b) AC-DC c) DC-DC d) AC-AC
a)5 b) 2 c) 3 d) 4
281) In Alco loco fuel oil regulating valve is set at ____ kg/cm² ( b )
a)3 b) 4 c) 5 d) 6
282) In Alco loco lube oil relief valve is set at ____ kg/cm² ( d )
a)6 b) 7 c) 8 d) 9
a)86 b) 76 c) 96 d) 68
391. MR safety valve is set at ______ kg/cm² ( d )
a)8 b) 8.5 c) 10 d) 10.5
288) In Alco Traction Motor gear case is having ___ no. of bolts ( c )
a)5 b) 6 c) 7 d) 8
290) In Alco loco, if water level comes down below 1” from bottom of tank ____ safety
device will operate ( c )
291) Wheel numbers to which brake blocks get applied when hand brake is applied in
WDG3A loco ( b )
a)L1,L2 b) R1,R2 c) L1,R1 d) L2,R2292)
292) Dust exhaust motors are available for ______ type of filters ( b )
a)AC to DC b) DC to AC c) DC to DC d) AC to AC
a)AC to DC b) DC to AC c) DC to DC d) AC to AC
a) Water b) Oil & water c) Super charged air & Water d) None
a)4 b) 8 c) 10 d) 12
307) In Alco loco fuel oil relief valve is set at ____ kg/cm² ( a )
a) 5 b) 2 c) 3 d) 4
308) In Alco loco fuel oil regulating valve is set at ____ kg/cm² ( b )
a) 3 b) 4 c) 5 d) 6
a) 86 b) 76 c) 96 d) 68
a) 8 b) 8.5 c) 10 d) 10.5
a)5 b) 6 c) 7 d) 8
315) In Alco loco, if water level comes down below 1” from bottom of tank _________ safety
device will operate ( c )
a)AC to DC b) DC to AC c) DC to DC d) AC to AC
a)AC to DC b) DC to AC c) DC to DC d) AC to AC
a)60 b) 70 c) 90 d) 80
a)10 b) 8 c) 12 d) 10.5
a) MR1 b) MR2 c) FP d) BP
330) Fuel pump motor is not working though all circuit breakers are switched ‘ON’, the reason
may could be ________. ( d )
336) In Twin beam head lights __ volts halogen lamps are used ( c )
a)72 b) 32 c) 24 d) 20
337) In twin beam head light system in DC-DC converter if one unit is defective the stand by
unit can be brought into function by ( a )
339) In MCBG loco when shut down occurs due to over speed
a) Fail the loco b) Lock rack of L5 c) lock left side racks d) Ignore
553. If battery ammeter is showing over charging, what may be the reason? ( c )
a) BS open b) MB1 tripped c) Battery defective d) AGFB tripped
555. If battery ammeter shows over charging, what may be the reason? ( c )
a) BS open b) MB1 tripped c) VRP defective d) AGFB tripped
560. If BA ammeter shows discharging and not rectified what is the action to be taken?( d )
a)Work for 4 Hours b) Do not Shut down
c)Do not allow for Automatic Shut Down d) All of the above
564. If engine is not cranking which switch is to be checked on the front panel? ( c )
a) Battery Switch b) MUSD c) ECS d) G.F.Switch
565. If engine is not cranking which contactors are to be checked? ( d )
a) FPC Contactor b) CK1 Contactor c) CK2 Contactor d) All the above
566. If engine is not cranking which power contactor interlocks are to be checked? ( a )
a)P22, S1 b) P22, S21 c) P21, S1 d) P1, S1
567. For engine cranking what should be MUSD & ECS position? ( b )
a)RUN, RUN b) RUN, IDLE c) STOP, RUN d) STOP,IDLE
568. If FPC Contactor closing but engine is not cranking what may be the reason? ( c )
a) MB1 Tripped/Off b) MB2 Tripped/Off
c) FPB Tripped/Off d) MFPB1 & MFPB2Tripped/Off
569. If engine is cranking but not firing what may be the reason? ( d )
a) OPS1 Stuck up b) LWS Operated c) OSTA Tripped d) All the above
570. If engine is cranking but not firing with indication what may be the reason? ( a )
a) LWS Operated b) OSTA Tripped c) SAR Defective d) All the above
571. If engine is cranking but not firing while starting what may be the reason? ( d )
a) FPM not working b) Fuel Booster Pump defective
c) Love joy coupling defective d) All the above
573. What is the reason if engine is cranking, firing but not holding? ( d )
a) SAR Inter lock defective b) OPS Defective
c) Lube oil system defective (Below1.6Kg/Cm2) d) All the above
574. What is the reason if engine shutdown automatically on run? ( d )
a) MB2 Tripped b) MFPB1 &MFPB2Tripped c) FPB Tripped d) All the above
585. To reset only Buzzer what is the action required by the Driver? ( c )
a) SW1 &SW2 b) SP1 &SP2
c) Switch On normal flasher light and SW1&SW2 Off d) All the above
592. If engine shuts down with hot engine alarm which safety device operates? ( b )
a) ETS b) LWS c) SAR d) OPS
593. If engine is running with Hot engine alarm which safety device is operated? ( c )
a) LWS b) OPS c) ETS d) SAR
598. In AC/DC Locos during cranking which relay protects Aux and Exc. Gens? ( c )
a) SAR b) GR c) TDR d) WSR
662. Which circuits are protected by GR1 & GR2 after earthling? ( c )
a) Power Circuit b) Control circuit c) Power and Control circuits d) Nothing
663. What are the changes in single BKT Locomotives as compare to Double BKT Loco’s?( d )
a) 3BKR Relays b) P22 & P32 Contactors location interchanged
c) During DB 5Power contactors will energize d) All the above
666. If BKT or Reverser is not operating properly what is the action to be taken? ( b )
a) Fail the loco b) Operate manually with `L’ rod c)Shutdown engine d) Engine Idle
668. While working LE's Loco pilot should check and ensure __ before starting. ( c )
a) Head light b) Flasher Light
c) Brake Power physically and not moving of Loco up to 2nd Notch on application of SA-9
d) Marker Lights
670. When Head light become defective speed of the train shall not exceed ? ( c )
a) 20kmph b) 30kmph c) 40kmph d) 50kmph
671. What should be done by LP for releasing proportional loco brakes during ( c )
A9 application?
a) Pressing BKIV foot pedal b) Application of DB c) Either A or B d) None
677. Side load pads are provided in this type of under truck ( b )
a) Tri mount bogie b) Fabricated bogie c) HTSC bogie d) both b and c
688. If radiator fan is not working during continuous hot engine alarm switch ON ( a )
a) ERF b) LWS c) DMR d) TR A
693. In M.U. operation if trailing loco ¾" coc alone kept in open position ( d )
a) BP will not destroy in any position b) BP will destroy only in emergency position
c) Loco brakes will not apply d) BP will not create to 5 kg/cm2
697. In Medha microprocessor loco if TM No. 4 & 5 are isolated loco will start with( b )
a) Series parallel combination b) Parallel combination
b) series parallel with shunt combination d) Parallel with shunt combination
708. In Medha Microprocessor loco if TM2 & 5 are isolated loco will start with ( a )
a) Series-parallel combination b) Parallel combination
c) Parallel with shunt combination d) Series-parallel with shunt combination
709. Engine should not be cranked if it is shut down for more than ( c )
a) 24 hrs. b) 16 hrs. c) 48 hrs. d) 32 hrs.
710. If MCBG power breaker is in OFF position during cranking engine will ( b )
a) not Crank b) not Fire c) not Hold d) a and b
717. In single BKT/Rev Loco during DB which power contactors will not pick up?( d )
a) P2 & P22 b) S21 &S31 c) S1, S21 & S31 d) Both a and b
720. In GE governor loco during cranking if MUSD is in stop position engine will ( d )
a) Crank b) Not fire c) Not hold d) Not crank
721. In WW governor loco not provided with MUSDR relay during cranking if ( b )
MUSD is in STOP position during cranking engine will
a) Crank b) Not fire c) Not hold d) Not crank
733. HP of WDP1 is ( d )
a) 1400 b) 1800 c) 2400 d) 2300
746. Fuel pump motor is not working though the all circuit breakers are ( d )
switched ON, the immediate reason could be_________
a) ERF not closed b) R1 and R2 not picked up
b) GFC not picked up d) FPC not picked up
747. Pre-lubrication is required if an engine that has been shut down for more ( a )
than______ hours
a) 48 b) 24 c) 12 d) 8
748. What is the Safety Device provided in the Lube oil system? ( c )
a) GFOLR b) OSTA c) LLOB d) LWS
751. From where the control air pressure will get air pressure_______ ( b )
a) MR2 b) MR1 c) BKTs d) J filter
752. MR (compressed air pressure) Unloading will takes place at _____kg /cm² ( c )
a) 8 b) 9 c) 10 d) 11
755. During one of the following occasions Hot engine alarm indication will get ( c )
a) Continuous 8thnotch working b) Excess load
c) Water pump not working d) Full water in expansion tank
757. During one of the following occasions Hot engine alarm indication will get ( c )
a) Continuous 8thnotch working b) Excess load
c) Water pump not working d) Full water in expansion tank
762. The following shall not be used for extinguishing fires on electrical ( c )
equipment.
a) dry chemical powder b) foam c) water d) none of these
764. What combination of trains are Permitted for running long haul train ? ( d )
a) Empty/Empty b) loaded/Empty c) Loaded/Loaded d) All the above
766. While taken over charge of Loco, if Flasher light glows but does not ( a )
flash/blink, what action would you take?
a) Fail the loco. b) Will work to nearest shed
c) Inform PRC & work further. d) Work normally
767. What precaution should be taken for conducting Air brake self test in GM ( d )
locos?
a) Secure loco b) Secure formation
c) Detach loco and secure d) Secure both & don’t detach from formation.
768. What should be done first for changing consol in WDG 4 / WDP 4 locos ? ( a )
a) Disable working control stand & enable nonworking control stand
b) Enable working control stand & disable nonworking control stand
c) As per convenience
d) None
777. In WDP4/WDG4 loco if LLOB is in tripped position during cranking engine will ( d )
a) Crank b) Not Fire c) Not hold d) Not crank
779. In WDP4/WDG4 banker loco working C/S, L/T switch should be kept in ( c )
a) Lead b) Trail c) HLPR d) Test
784. In WDP4 /WDG4 loco before conducting air brake self test ( a )
a) Recycle MAB b) Recycle TCC1 and TCC2 c) Recycle Air drier breaker.
D) Both a & b
787. In WDP4/WDG4 when continuous wheel slip is experienced due to locked axle ( c )
a) Isolate the defective TM b) Isolate the defective speed sensor
b) Fail the loco immediately d) Isolate the defective truck
788. In WDP4/WDG4 loco while conducting BP leakage test. L/T switch should ( d )
be kept in
a) Lead b) Trail c) Helper d)Test
790. In WDP4/WDG4 loco while conducting BP leakage test L/T switch should ( c )
be kept in
a) Lead position b) Trail position c) Test position d) Helper
796. ____is the main power supply of CCB for the CCB system. ( b )
a) DCU b)VCU c) PCU d) DVR
798. CCB fault code for Brake Pipe Leakage Failure ____________ ( c )
a) 6A b) 6C c) 6B d) 6D C
799. Emergency brake application is accomplished by_______ valve provided at the
lower left of each console ( a )
802. The EM2000 reads main reservoir air pressure from ______ transducer. ( d )
a) BPT b)BCT c) ERT d) MRPT
803. What is the code for Brake pipe control failure in self test ? ( b )
a) 8A b) 6A c)10A d) 22A
804. What is the code for Brake pipe leakage failure in self test? ( a )
a) 6B b) 10B c)6F d) 6S
805. What is the function of KE valve in CCB system in WDPG4 Loco motive ? ( a )
a) provides pneumatic back Up b) Creation of BP
c) Creation of FP d) Emergency application
806. Why Maximum of 5.2kg/cm2 brake cylinder pressure is used in place of
3.5kg/cm2 as in conventional locos ? ( c )
a) High horse power loco b) Speed is more c) A single shoe system is used
d) To have effective brake power
810. Do not crank engine for more than _____with starting motors in HHP. ( d )
a) 30seconds b) 1minutes c) 10seconds d) 20 seconds
a) less than 200 b) less than 100 c) 100 More than d) 100 less than 500
826. If the TM temperature is greater than _____degree Celsius the inverter will
De-rate to keep the traction motor temperature in control ( a )
a) 200 b) 100 c) 95 d)92 `
830. Shutting down of all diesel engines in a consist is accomplished ___ relay ( c )
a) DMR b) GCR c) SDR d) FLR
a) GTO1 b) The No.1 bogie traction inverter (TCC1) computer and associated circuits
c) TM1 d) DCL
837. Whenever DC link exceeds 3600volts,the ____ trips, which fires a Hard
Crowbar. ( b )
a) AC control b) TCC Break Over Diode (BOD)
c) Local control breaker d) GR
838. Whenever DC link voltage exceeds 3200 volts ,the TCC fires a ___ crow bar( c )
a) Hard Crowbar b) Sneaky crow bar c) Soft Crowbar d) GR
841. What is the maximum permissible speed of (designed for) WDG4 locomotives( b )
a) 150kmph b) 120kmph c)100kmph d)75kmph
844. The purpose of Turbo lube pump in WDP4 Locomotive before cranking is ( c )
a) To lubricate the Turbo b) To remove the residual heat
c) To lubricate turbo Bearing d) To lubricate crank shaft
845. Turbo lube pump should be running for ______minutes after engine is shutdown if engine
was running at 5th notch and higher for 60minutes prior to engine shut down. (
b )
a) 15 b) 35 c) 20 d) 45
851. The EM2000 will consider a temperature probe failed if it reads _________ ( b )
a) Less than -155 degrees C or greater than 150 degrees C
b) Less than -55 degrees C or greater than 150 degrees C
c) More than -55 degrees C or greater than 150 degrees C
d) Less than -55 degrees C or greater than 250 degrees C
854. What precaution should be taken for conducting Air brake self test in GM locos?( d )
a) Secure loco b) Secure formation c) Detach loco and secure
d) Secure both, close BP & FP COC of loco towards formation.
855. What should be done first for changing console in WDG 4 / WDP 4 locos ? ( a )
a)Disable working control stand & enable non working control stand
b) Enable working control stand & disable non working control stand
c)As per convenience d) None
a) MR1 b) MR2 c) BP d) FP
b) MR1 b) MR2 c) BP d) FP
a) 120 b) 40 c) 60 d) 30
a) 2 b) 1 c) 3 d) None
890. During engine starting do not hold the fuel prime/engine start switch (FP/ES) to ES
position for more than ____ sec. ( a )
a) 20 b) 30 c) 60 d) 80
891. Backlash to be maintained between ring gear and starter motor pinion ( c )
a) 0.008”-0.016” b) 0.007”-0.025” c) 0.015”-0.040” d) 0.020”-0.030”
965. WDP4D is a ( b )
a) Single cab loco b) Dual cab loco
c) Dual cab loco with disc brake d) Dual cab loco with Hotel load
982. Which of the following sensor are fitted in the traction motor? ( a )
a) Temperature sensor b) Voltage sensor
c) Air Pressure sensor d) All of the above
984. Which of the following changes are done during conversion from ( d )
4000 HP to 4500 HP
a) 54” Radiator fan is introduced instead of 52” radiator fan
b) 8th notch engine rpm is increased from 904 rpm to 954 rpm
c) OSTA tripping rpm is increased from 1035 to 1085
d) All of the above
996. During cranking of engine in cold condition, engine rpm not hold due to ( c )
a) Improper adjustment of governor compensation needle valve
b) Worn out Teflon seal of power piston
c) Both a & b
d) None of the above
1013. Clearance between flywheel ring gear teeth and EPU must be a gap of ( b )
a) 0.020”± 0.005” b) 0.025” ± 0.005” c) 0.030” ± 0.005” d) 0.035” ± 0.005”
1017. How will you check the working of soak back pamp? ( d )
a) After engine shut down & by opening no.1 oil pan hand hole cover
b) After engine shut down & by opening no.8 oil pan hand hole cover
c)After engine shut down & by opening no.9 oil pan hand hole cover
d)After engine shut down & by opening no.16oil pan hand hole cover
1023. Don’t shift the ISOLATION Switch to run position immediately after engine start, ( a )
otherwise Engine will shut down due to
a )EPD low water button & LLOB operation. b) EPD crankcase button & LLOB operation
c)Only LLOB operation. d) None of the above
1025. Gap between TM blower intake ring and blower wheel on both sides of wheel ( b )
assembly i.e.MA/TM is
a) 2.5 to 5 mm b) 3.5 to 5mm c) 4.5 to 5mm d) none of the above
1031.WDG4DD is a ( c )
a)single cab loco b) Duel cab loco
c) Duel cab loco with disc brake d) Duel cab loco with Hotel load
1033. In HHP MU, loading & unloading of compressor of both loco is synchronized by ( c )
a) MVCC of leading loco b) MVCC of trailing loco
c) CMPSYN d) None of the above
1034. In HHP MU ( d )
a) Loading of compressor of both loco is occurred at same pressure
b) Unloading of compressor of both loco is occurred at same pressure
c) Loading & unloading of compressor of both loco is occurred at same pressure
d) Loading & unloading of compressor of both loco is occurred at different pressure
1036. Which of the following NDT process is used for auxiliary generator drive shaft testing
( a )
a) ZYGLO testing b) MPT c) UST d) None of the above
1037. In which schedule height is cattle guard & rail guard is measure and recoded? ( b )
a) T-30 & above b) T-90 & above c) T-180 & above d) 3Yeatly & above
1039. How many magnetic poles are in radiator fan when run in full speed? ( a )
a) 8pole b) 12pole c) 16pole d) None of the above
1042. Which of the following sensor is not fitted in the traction motor? ( c )
a) Current sensor b) Speed sensor c) Air pressure sensor d) All of the above
1045. Which of the following component are recently fitted in HHP Locomotive ( d )
a ) APU b) MCBG c) CREDI d) All of the above
1049. During EPD testing if throttle is above third notch then shut down will occur in ( d )
a ) Approximately 60 seconds. b) Approximately 40 seconds.
c) Approximately 35 seconds. d) Approximately 02 seconds.
1057. How many magnetic poles are connect in radiator fan circuit when run slow speed? ( c )
a) 8pole b) 12pole c) 16pole d) None of the above
1058. In WDP4DH, DH stand for ? ( a )
a) Duel cab loco with Hotel load facility b) Double head loco with Hotel load facility
c) Disk brake loco with Hotel load facility d) None of the above
1064. There are how many batteries are fitted in WDG4D Locomotive? ( b)
a) 2 b) 8 c) 10 d) none of the above
1072. In MEDHA control system when turbo cool down cycle is running, radiator ( a )
fan will drop at
a) Below 73oc b) Below 79o c c) Above 85oc d) 96oc
1077. In WDG4/WDP4 loco while conducting BP leakage test L/T switch should
be kept in ( c )
a) Lead position b) Trail position c) Test position d) Helper position
1083. During EPD testing at idle engine should not be shut down before ( d )
a) 120 seconds b) 50 seconds c) 60 seconds d) 35 seconds
1088. During EPD testing (engine running above 3rd notch) engine should be shutdown in ( d )
a) 120 seconds b) 40 seconds c) 35 seconds d) immediately
1106. Normal air box pressure (BAP) in HHP Locomotive at full speed & full load is ( c )
a) 1.1kg/cm2-1.75kg/cm2 b) 1.5kg/cm2-1.95kg/cm2
c) 1.4kg/cm2-1.75kg/cm2 d) 1.4kg/cm2-1.50kg/cm2
a) 4 b) 2 c) 1 d) 8
1120) Output of PSM 305 card is _______ Volts. ( a )
a) 5 b) 10 c) 12 d) 15
1121) Transition picks up at __________ kmph in WDG3A loco. ( a )
a) 41.5 b) 42.5 c) 46.5 d) 52
1122) Siemens HHP loco has _____ number of TCC. ( b )
a) 1 b) 2 c) 6 d) 3
1123) PRS unit is available in __________governor ( c )
a) GE b) WOODWARD c) MCB d)NS16
1124) In HHP loco Battery Charging Assembly is located in _________ Panel ( b )
a) ECC1 b) ECC2 c) ECC3 d) Breaker
1125) Type of battery used in WDG4 loco is ( a )
a) Lead acid b) Nickel Cadmium
c) Lithium ion d) Any one of a,b,c
1126) In HHP loco, Function of DVR is to control ( c )
a) Main generator b) Engine RPM c) AG output d) CA output
1127) FCF2A contactor is used in _______ circuit ( c )
a)TCC blower b) Filter blower c) Radiator fand) FPM
1128) If MFPB trips on RUN engine will _________ ( b )
a) Idle b) shutdown c) over shoot d) none
1129) In HHP loco, the normal maximum DC Link voltage is ____________. ( d )
a)600 b) 2000 c) 2500 d) 2600
1130) In HHP loco, TCC Blower is getting power supply from___________. ( d )
a) ECC1 b) ECC2 c) TA d) CA
1131) _____________Breaker is yellow labelled. ( b )
a) Air brake b) computer c) TA d) CA
1132) Medha HHP loco has _____ number of Traction computers ( c )
a) 1 b) 2 c) 6 d) 3
1133) Actuator unit is available in __________governor ( c )
a) GE b) WOODWARD c) MCBG d)NS16
1134) In HHP loco auxiliary output side 250 Amps breaker is located in _______( b )
a) ECC1 b) ECC2 c) ECC3 d) Breaker Panel
1135) FCS contactor is used in _______ circuit ( c )
a) TCC blower b) Filter blower c) Radiator fand) FPM
1136) In HHP loco ______ sensor measures Turbo RPM. ( a )
a) TPU b) EPU c) MPU d) BAP
1137) The number of IGBT modules in EMD HHP Loco is __________. ( c )
a) 1 b) 2 c) 6 d) 3
1138) In HHP loco MRPT is available in__________ compartment. ( c )
a) ECC1 b) ECC2 c) ECC3 d) Breaker Panel
1139) Model no. of Traction Motor Speed Sensor used in MEP.Ver.3 loco is______( a )
a) T.818 b) T.815 c) RDB d) ADB
1140) No of brush arms in 4907 TM is________ ( d )
a) 1 b) 2 c) 6 d) 4
1141) No. of batteries in WDP4D loco is _____ ( b )
a) 8 b) 10 c) 6 d) 4
1142) Total HP of auxiliaries in WDG3A loco is ______ ( a )
a) 207 b) 186 c) 200 d) 250
1143) Position of LCR in Woodward governor for maximum excitation is_____ ( a )
a) 5.30 b) 6.30 c) 11 d) 3
1144) Power deration starts if TANGI current above _______mA. ( a )
a) 400 b) 500 c) 800 d) 700
nd
1145) During 2 notch ______ solenoid will pickup. ( a )
a) AV b) BV c) Cv d) AV, Bv & CV
1146) Rating of starting fan fuse in HHP loco is ____ Amps ( d )
a) 800 b) 400 c) 200 d) 300
1147) Pre lubrication will work for ________ minutes in HHP loco. ( d )
a) 30 b) 20 c) 10 d) 15
1148) Output of HHP loco auxiliary generator is _______ ( c )
a) 72 V DC b) 72 V AC c) 55 V AC d) 74 V DC
1149) In MEP loco __________ is used to sense power ground ( c )
a) GR1 b) GR2 c) TANGI d) BANGI
1150) The clearance between TM commutator and brush holder is________ ( a )
a) 1.6 to 2.5mm b) 2.5 to 4.5 mm c) 1 to 2 inch d) 1 to 3 mm
1151) Operating air pressure of BKT/REV is ( b )
2 2
a) 6 Kg / cm b) 5 Kg / cm c) 8 Kg / cm d) 10 Kg/ cm2
2
1152) In ALCO loco Wheel slip fault will be declared if difference between TM RPM ( a )
exceeds___,
a)15 b)125 c) 10 d) 25
1153) AG is controlled by _________ in EMD loco ( c )
a) FCF b) PSM c) DVR d) PRG
1154) Blended brake is available in _________ loco ( d )
a) WDM3A b)WDG3A c)WDM3D d) WDP4
1155) Flasher Light will work if ______ pressure switch alone drops. ( a )
a) P2 b) P1 c) PCS2 d) VCD
1156) In AC-DC loco, CK2 is connected to ________ machine ( a )
a) AG b) EG c) TG d) TA
1157) In AC-DC loco, CK1 is connected to ________ machine ( b )
a) AG b) EG c) TG d) TA
1158) __________ gear is provided in Tacho generator. ( a )
a) Nylon b) stainless c) cast iron d) Rubber
1159) In HHP loco, TPU sensor measures ___________ ( a )
a) Turbo RPM b) Engine RPM c) TM RPM d) CA RPM
1160) No. of brushes in HHP loco EMD Traction alternator is__________ ( d )
a) 2 b) 4 c) 8 d) 6
1161) After application of A9 auto flasher will not work for _____ seconds ( a )
a) 60 b) 30 c) 90 d) 10
1162) During continuous supply to EPG, MR pressure_________ ( a )
a) drop b) buildup c) maintain normal d) leaks
1163) _______________ Button is to be pressed to avoid conjunction brake ( a )
a) Quick releaseb) VCD c) AFL Reset d) Release/Run
1164) _________ relay operates EPG in MEP loco ( a )
a) CMR b) DCR c) MVR d) RT5X
1165) _________ relay operates EPG in MEP loco ( c )
a) CMR b) DCR c) MVR d) RT5X
1166) ___________________ is used in between TM commutator segments ( c )
a) porcelain b) copper c) Mica d) Rubber
1167) In MEP loco engine RPM is measured by_________ ( a )
(a) ESS (b)Tacho (c) TPU sensor (d)none of above
1168) In Alternator R-Y-B coils are in ( b )
a) Rotor b) Stator c) Armature d) None
1169) Short term memory will be recorded in a time interval of _______sec. ( d )
a) 10 Sec b) 20 Sec c) 2 Sec d) Each Sec
1170) Total no. of batteries in WDG4 loco is________ ( b )
a) 10 b) 8 c) 12 d) 6
1171) Reverse bias in diode means connecting ( b )
a) +ve to anode b) –ve to anode c) -ve to cathode d) None
1172) Rating of MB1 is __________ Amps ( b )
a) 150 b) 200 c) 250 d) 15
1173) Output of headlight DC-DC converter is _______________ ( c )
a) 72V DC b) 72V AC c) 24V DC d) 24 V AC
1174) In MEDHA VER.3 WDG3A loco, LAM gets supply from ________ ( c )
a) TM current b) LAM Shunt c) MEP- output d) TG
1175) In HHP loco________valve controls MR cutin/ cutout ( a )
a) MVCC b) EPG c) EBT d) RT5X
1176) In ALCO loco, if ______ relay drops then auto flasher will work. ( c )
a) DMR b) VCDR c) AFLR d) FLSHR
1177) The number of DC Link Breaker in Medha Loco is __________. ( d )
a) 2 b) 4 c) 8 d) 6
1178) BKBL is getting power from _________ ( d )
a) TG b) TA c) EG d) TM
1179) STA is available in__________ ( b )
a) ECC1 b) ECC2 c) ECC3 d) Breaker Panel
1180) Specific gravity lead acid battery at the end of charging cycle is_____ ( a )
a) 1.245 b) 1.210 c) 1.220 d) 1.200
1181) No of brush arms in BHEL Traction Generator is________ ( a )
a) 10 b) 6 c) 8 d) 12
1182) NLV of WDG3A loco is _________ volt. ( c )
a) 750 b) 1000 c) 1100 d) 1050
1183) Total HP of auxiliaries load in WDM2 loco is ______ ( a )
a)186 b) 207 c) 200 d) 250
1184) Position of LCR in Woodward governor for minimum excitation is _____ ( b )
a) 5.30 b) 6.30 c) 11 d) 3
1185) Low idle RPM of 4500 HP loco is _______. ( a )
a)200 b) 260 c) 400 d) 450
th
1186) 8 notch RPM of 4500 HP loco is _______. ( a )
a) 960 b) 900 c) 1000 d) 1050
1187) Low idle RPM of WDG3A loco is _______. ( a )
a)350 b) 260 c) 400 d) 450
th
1188) 8 notch RPM of WDG3A loco is _______. ( a )
a) 1050 b) 900 c) 1000 d) 110
th
1189) During 8 notch ______ solenoid will pickup. ( d )
a) AV b) BV c) AV & Bv d) AV, Bv & CV
1190) In HHP loco if EPD is tripped engine will ________. ( b )
a)shutdown without message b) shutdown with message
c) idle with message d) idle without message
1191) Rating of radiator fan breaker rating in HHP loco is ____ Amps ( b )
a) 800 b) 400 c) 200 d) 300
1192) Before cranking, Pre lubrication will work for ________ minute in ALCO loco.( d )
a) 30 b) 20 c) 60 d) 1
1193) In MEP loco __________ is used to sense control ground ( d )
a) GR1 b) GR2 c) TANGI d) BANGI
1194) In HHP loco ________ relay controls auto flasher ( c )
a) AFLR b) DMR c) FLSHR d) ERR
1195) In HHP loco ________ relay drops auto flasher will work ( c )
1278) Total numbers of carbon brushes used in BKBL/Grid blower motors are ( c )
a) 12
b) 24
c) 8
d) 6
1279) The brush grade used in T/M type 5002 AZ is………… ( a )
a) EG14D
b) EG15D
c) EG225
d) EG55
1280) How many poles are in rotor winding of traction Alternator type 10106 AZ ( a )
a) 10 poles
b) 8 poles
c) 12 poles
d) 6 pole
1281) The stator winding of Traction Alternator type 10106 AZ (In WDP1 loco) is
connected as ( c )
a) Star connected b)Delta Connected
b) Star connected with two parallel path per phase
c) Delta connected with two parallel path per phase
1282) Tacho-generator have total numbers of magnetic poles
a) 4
b) 2
c) 6
d) 8
a) 0.002”
b) 0.005”
c) 0.006”
d) 0.007”
1290) Function generator card is also known as……. ( c )
a) 188 card
b) 187 card
c) 293 card
d) 254 card
1291) Traction motor-165 is a …. ( a )
a) D.C. Series Motor
b) A.C. Series Motor
c) D.C. Shunt Motor
d) Induction Motor
1303) At which temperature Traction Motor type -165M pinion is mounted on shaft (in
degree centigrade) ( a )
a) 170⁰C above ambient temperature
b) 140⁰C above ambient temperature
c) 200⁰C above ambient temperature
d) 500⁰C above ambient temperature
1304) Traction Motor type -165M pinion never be heated above ( c )
a) 100°C b) 150⁰C c) 220°C d) 300⁰C
1305) Which type of bearing fitted in pinion end of Traction Motor type -165 ( b )
a) NU320
b) NU330
c) NU328
d) NU326
1306) Which type of bearing fitted in comm. End of Traction Motor type -165
( c )
a) NU320
b) NU330
c) NH320
d) NI350
1307) Gap between holder assembly and Comm. of Traction Motor type -165M (in mm) is
( c )
a) 10mm to 11mm
b) 7mm to 8 mm
c) 1.6 mm to 2.4 mm
d) 4.5 mm to 6.5 mm
1308) New commutator diameter of Traction Motor type 7362 CGL make (in mm) is...
( c )
a) 300mm
b) 490mm
c) 380mm
d) 600mm
1309) Minimum usable diameter of Comm. of Traction Motor type 7362 in mm is….
( c )
a) 400mm
b) 600mm
c) 360mm
d) 500mm
1310) What is the brush spring pressure of Traction Motor type 7362 Brush holder
( a )
a) 3.0 kg to 3.6 kg
b) 8.0 kg to 9.0 kg
c) 9.0 kg to 10.0 kg
d) 10.0 kg to 11.0 kg
a) C Solenoid
b) CD Solenoids
c) AD Solenoids
d) None
1319) Traction Motor (make-CGL-Q7362) has total numbers of interpole… ( c )
a) 6
b) 10
c) 4
d) 8
a) BS & MB1 b) BS & MB2 c) MB1 & AGFP d) MB2 & MFB
1377) Before switching ON GF emergency switch _________________ to be ensured ( c)
a) FPC b) FSC c) CK1 & CK2 d) R1 & R2
1378) BKBL gets supply from the _________________ ( c)
a) batteries b) auxiliary generator c) grids d) MG
1379) BL box is available in _______________ loco ( d)
a) WDM2 b) WDM3D c) WDS6 d) WDP3A
1380) BS is located in ________ in WDM3A ( b)
a) Control compartment b) nose compartment
c) gen. room d) under truck
*****
ELECTRICAL
1. Fan blade thickness in modified fan of Traction Alternator is
A. 6 mm
B. 2 mm
C. 10 mm
D. 20 mm
12. The total nos. of main pole in Auxiliary Machine type AG-51
are
A. 8
B. 2
C. 6
D. 4
14. Gear ratio of Eddy current clutch gear unit (Right angle gear
box) is
A. 1:1.312
B. 1:1.321
C. 1:1.231
D. 1:1.213
16. The nominal air gap between inner and outer drum of ECC
(Eddy current clutch) is
A. 0.8 to 1.2mm
B. 1.9mm to 2 mm
C. 2mm to 3 mm
D. 9mm to 4mm
20. Type of the bearings used in the vertical shaft of the ECC is
A. K639/K632
B. K635/K632
C. K636/K632
D. K655/K632
21. Type of the bearings used in the horizontal shaft of the ECC
is
A. K45290/K45220
B. K45291/K45220
C. K45280/K45220
D. K45285/K45220
45. Weight of complete TM-165 with pinion & axle caps is.
A. 3500 kg
B. 2800 kg
C. 3340 kg
D. 3600 kg
85. Generator field cover load relay operating current limit is..
A. 50 Amp
B. 100 Amp
C. 280 Amp
D. 400 Amp
91. In AC/DC loco time delay relay (TDR) is provided for time
delay of
A. 4 seconds
B. 8 seconds
C. 1.8 seconds
D. 12 seconds
105. If the reference voltage is more than 24.4 volts, the defects
in
A. LCP
B. SP
C. GCR
D. Pilot valve
112. The gap between ECC slip rings & brush holder is to be
kept
A. 5mm
B. 8mm
C. 2mm
D. 15mm
GM LOCOMOTIVE
ELECTRICAL
Q. No. ANSWER
1. A 26. A 51. C
2. C 27. C 52. A
3. D 28. A 53. C
4. A 29. B 54. A
5. A 30. C 55. A
6. A 31. C 56. A
7. A 32. C 57. C
8. B 33. A 58. B
9. A 34. D 59. C
88. C 102. A
89. C 103. C
GM LOCOMOTIVE
Q. No. ANSWER
1. C 13. B 25. B
2. A 14. B 26. C
3. C 15. C 27. C
4. C 16. B 28. C
5. D 17. A 29. B
6. A 18. C 30. B
7. B 19. C 31. A
8. C 20. D 32. B
9. A 21. B 33. B
12. C 24. B
TRANSFORMER
1. What is Transformer?
a) Transformer is a device used to convert low alternating voltage to a high alternating voltage
b) Transformer is a device used to convert alternating current to direct current
c) Transformer is a device used to convert low alternating current to a high alternating current
d) Transformers are used only for low alternating voltage
Answer: a
Answer: a
3. What is the working principle of a Transformer?
a) Transformer works on the principle of self induction
b) Transformer works on the principle of mutual induction
c) Transformer works on the principle of ampere law
d) Transformer works on the principle of coulomb law
Answer: b
4. Transformer ratings are given in _____________
a) kVA
b) HP
c) kVAR
d) kW
Answer: a
.
Answer: b
6. Current transformers are __________________
a) parallel connected type of instrument transformers
b) series connected type of instrument transformers
c) parallel connected normal transformers
d) series-parallel connected type of instrument transformers
Answer: b
7. Which of the following is not a part of transformer installation?
a) Breather
b) Conservator
c) Exciter
d) Buchholz relay
Answer: c
8. Transformer core is generally made of ___________
a) Cannot be determined
b) Can be made with any of the above method
c) By stacking large number of sheets together
d) Single block of core material
Answer: c
9. The purpose of the transformer core is to provide ____________
a) Low reluctance path
b) High inductive path
c) High capacitive path
d) High reluctance path
Answer: a
10. Transformers are generally designed for ___________
a) one-time use
b) off-site problem solving
c) short-time use
d) on-site problem solving
Answer: d
Answer: c
2. Why is the length of the yoke made larger?
a) to protect the armature windings
b) to cover the armature windings
c) to cover the field windings
d) to cover and protect the field windings
Answer: d
3. What is the formula for the depth of the yoke?
a) depth of yoke = thickness/2
b) depth of yoke = thickness
c) depth of yoke = 2*thickness
d) depth of yoke = 3*thickness
Answer: b
5. What is the formula in order to check the rigidity?
a) moment of inertia ≥ (weight of magnetic frame * radius2 * 10-6) / 225
b) moment of inertia ≤ (weight of magnetic frame * radius2 * 10-6) / 225
c) moment of inertia = (weight of magnetic frame * radius2 * 10-6) / 225
d) moment of inertia < (weight of magnetic frame * radius2 * 10-6) / 225
View Answer
Answer: a
6. What is the formula for the thickness of the ac machines?
a) thickness = 40 * inner diameter of frame/12
b) thickness = 40 + inner diameter of frame/12
c) thickness = 40 – inner diameter of frame/12
d) thickness = 40 * inner diameter of frame*12
Answer: a
7. What is the formula for the breadth of the ac machine?
a) breadth = 6 + 0.01 * inner diameter of frame
b) breadth = 6 – 0.01 * inner diameter of frame
c) breadth = 6 * 0.01 * inner diameter of frame
d) breadth = 6 / 0.01 * inner diameter of frame
Answer: a
.
(a) absolute
(b) indicating
(c) recording
(d) integrating
(e) none of the above
Ans: a
2. Which of the following instruments indicate the instantaneous value of the electrical
quantity being measured at the time at which it is being measured ?
Ans: b
3. _____ instruments are those which measure the total quantity of electricity delivered in a
particular time.
(a) Absolute
(b) Indicating
(c) Recording
(d) Integrating
Ans: d
Ans: d
(a) wattmeters
(b) voltmeters
(c) ammeters
(d) ohmmeters and resistance bridges
(e) all of the above
Ans: d
Ans: c
Ans: d
8. A _____ device prevents the oscillation of the moving system and enables the latter to
reach its final position quickly
(a) deflecting
(b) controlling
(c) damping
(d) any of the above
Ans: c
9. The spring material used in a spring control device should have the following property.
Ans: e
Ans: e
(a) ammeter
(b) voltmeter
(c) flux-meter
(d) ballistic galvanometer
Ans: a
Ans: c
13. Which of the following devices may be used for extending the range of instruments ?
(a) Shunts
(b) Multipliers
(c) Current transformers
(d) Potential transformers
(e) All of the above
Ans: e
(a) 10 A
(b) 30 A
(c) 60 A
(d) 100 A
Ans: d
15. For handling greater currents induction wattmeters are used in conjunction with
Ans: b
16. Induction type single phase energy meters measure electric energy in
(a) kW
(b) Wh
(c) kWh
(d) VAR
(e) None of the above
Ans: c
17. Most common form of A.C. meters met with in every day domestic and industrial
installations are
Ans: c
18. Which of the following meters are not used on D.C. circuits
Ans: c
Ans: d
Ans: e
Ans: b
Ans: c
Ans: a
Ans: a
Ans: c
26. An ammeter is a
Ans: a
Ans: a
Ans: c
Ans: a
Ans: a
(a) series
(b) parallel
(c) series-parallel
(d) none of the above
Ans: a
Ans: c
(a) linear
(b) non-linear
(c) either (a) or (b)
(d) neither (a) nor (b)
Ans: a
Ans: c
35. The resistance in the circuit of the moving coil of a dynamometer wattmeter should be
Ans: c
Ans: a
Ans: C
38. The pressure coil of a wattmeter should be connected on the supply side of the current
coil when
Ans: a
Ans: b
Ans: c
41. In a 3-phase power measurement by two wattmeter method, both the watt meters had
identical readings. The power factor of the load was
(a) unity
(6) 0.8 lagging
(c) 0.8 leading
(d) zero
Ans: a
42. In a 3-phase power measurement by two wattmeter method the reading of one of the
wattmeter was zero. The power factor of the load must be
(a) unity
(b) 0.5
(c) 0.3
(d) zero
Ans: b
43. The adjustment of position of shading bands, in an energy meter is done to provide
Ans: a
44. An ohmmeter is a
Ans: b
45. When a capacitor was connected to the terminal of ohmmeter, the pointer indicated a
low resistance initially and then slowly came to infinity position. This shows that capacitor is
(a) short-circuited
(b) all right
(c) faulty
Ans: b
Ans: c
47. The electrical power to a meggar is provided by
(a) battery
(b) permanent magnet D.C. generator
(c) AC. generator
(d) any of the above
Ans: b
(a) spring
(b) gravity
(c) coil
(d) eddy current
Ans: c
(a) 6 V
(b) 12 V
(c) 40 V
(d) 100 V
Ans: d
Ans: c
COMPUTERS
1. Who is the father of Computers?
a) James Gosling
b) Charles Babbage
c) Dennis Ritchie
d) Bjarne Stroustrup
Answer: b
2. Which of the following is the correct abbreviation of COMPUTER?
a) Commonly Occupied Machines Used in Technical and Educational Research
b) Commonly Operated Machines Used in Technical and Environmental Research
c) Commonly Oriented Machines Used in Technical and Educational Research
d) Commonly Operated Machines Used in Technical and Educational Research
Answer: d
Answer: d
9. Which of the following is the smallest unit of data in a computer?
a) Bit
b) KB
c) Nibble
d) Byte
Answer: a
10. Which of the following unit is responsible for converting the data received from the user into a computer
understandable format?
a) Output Unit
b) Input Unit
c) Memory Unit
d) Arithmetic & Logic Unit
Answer: b
11. Which of the following monitor looks like a television and are normally used with non-portable computer
systems?
a) LED
b) LCD
c) CRT
d) Flat Panel Monitors
Answer: c
12. Which of the following is not a type of computer code?
a) EDIC
b) ASCII
c) BCD
d) EBCDIC
Answer: a
.
13. Which of the following part of a processor contains the hardware necessary to perform all the operations
required by a computer?
a) Controller
b) Registers
c) Cache
d) Data path
Answer: d
14. Which of the following is designed to control the operations of a computer?
a) User
b) Application Software
c) System Software
d) Utility Software
Answer: c
15. Which of the following device use positional notation to represent a decimal number?
a) Pascaline
b) Abacus
c) Computer
d) Calculator
Answer: b
18. Which of the following defines the assigned ordering among the characters used by the computer?
a) Accumulation
b) Sorting
c) Collating Sequence
d) Unicode
Answer: c
19. Which of the following storage is a system where a robotic arm will connect or disconnect off-line mass
storage media according to the computer operating system demands?
a) Magnetic
b) Secondary
c) Virtual
d) Tertiary
Answer: d
20. Which of the following is known as the interval between the instant a computer makes a request for the
transfer of data from a disk system to the primary storage and the instance the operation is completed?
a) Disk utilization time
b) Drive utilization time
c) Disk access time
d) Disk arrival time
Answer: c
21. Which of the following devices provides the communication between a computer and the outer world?
a) Compact
b) I/O
c) Drivers
d) Storage
Answer: b
22. Which of the following are the input devices that enable direct data entry into a computer system from
source documents?
a) System Access devices
b) Data acquiring devices
c) Data retrieving devices
d) Data Scanning devices
Answer: d
23. Which of the following is the device used for converting maps, pictures, and drawings into digital form for
storage in computers?
a) Image Scanner
b) Digitizer
c) MICR
d) Scanner
Answer: b
25. Which of the following is known as the language made up of binary-coded instructions?
a) High level
b) BASIC
c) C
d) Machine
Answer: d
26. Which of the following package allows individuals to use personal computers for storing and retrieving their
personal information?
a) Personal assistance package
b) Graphics package
c) Spreadsheet package
d) Animation package
Answer: a
27. Which of the following is created when a user opens an account in the computer system?
a) SFD
b) MFD
c) Subdirectory
d) RFD
Answer: c
28. Which of the following is a technique that marked the beginning of computer communications?
a) User Environment
b) Batch Environment
c) Time Sharing
d) Message passing
Answer: c
29. Which of the following is a type of technique in which dumb terminals are connected to a central computer
system?
a) Time Sharing
b) Message passing
c) Batch environment
d) User environment
Answer: a
30. Which of the following service allows a user to log in to another computer somewhere on the Internet?
a) e-mail
b) UseNet
c) Telnet
d) FTP
Answer: c
.
31. Which of the following is not a type of computer on the basis of operation?
a) Digital
b) Analog
c) Hybrid
d) Remote
Answer: d
32. Which of the following type of computer is mostly used for automatic operations?
a) analog
b) digital
c) hybrid
d) remote
Answer: c
33. Which of the following invention gave birth to the much cheaper microcomputers?
a) PDAs
b) Microprocessors
c) Microcomputers
d) Mainframes
View Answer
Answer: b
34. Which of the following computers are lower than mainframe computers in terms of speed and storage
capacity?
a) Mainframes
b) Hybrid
c) Mini
d) Super
Answer: c
Answer: d
Mechatronics
Answer: b
7. Which among the following carry out the overall control of a system?
a) Graphical display
b) Sensors
c) Actuators
d) Digital controls
Answer: d
8. A humanoid robot is an example of _____
a) Artificial intelligence
b) Stand-alone systems
c) Large factory systems
d) High level distributed sensor microcontroller actuator
Answer: a
9. Where is the feedback generated by sensors in a mechatronics system given?
a) Input sensors
b) Comparators
c) Mechanical actuators
d) Output sensors
Answer: b
1. What converts physical input into output, among the basic parts of a measuring system?
a) Transducer or sensor
b) Signal conditioning
c) Intelligence
d) Display
Answer: a
2. The analog to digital conversion in a measurement system takes place inside _____
a) transducer
b) signal processor
c) display
d) led
Answer: b
Answer: b
5. Which type of error is caused due to friction or electrical capacitance?
a) Hysteresis
b) Zero
c) Systematic
d) Random
Answer: a
.
7. Which type of error always has the same and consistent value?
a) Random errors
b) Systematic errors
c) Zero errors
d) Hysteresis errors
Answer: b
.
8. The largest value for which the instrument output remains zero is ____
a) hysteresis error
b) resolution
c) sensitivity
d) dead zone
Answer: d
9. The function of the data transmission element is ____
a) to transfer data from one element to another
b) to Modify the data
c) to process the data
d) to separate the signal hidden in the noise
Answer: a
10. Which elements among the following is used to modify the data before display?
a) Data presentation element
b) Data transmission element
c) Data processing element
d) Variable manipulation element
Answer: c
1. Which is the first aspect which needs to be considered in the Mechatronics design process?
a) Hardware design and simulation
b) Conceptual design
c) Mathematical modelling
d) Modelling and simulation
Answer: d
2. In the level of integration of Mechatronics system, an example of the first level is _____
a) fluid valves
b) automatic machine tools
c) industrial robots
d) microprocessors
Answer: a
4. What is the role of the second level in the mechatronics system design?
a) Integrates microelectronics into electrically controlled devices
b) Integrates electrical signal with mechanical action
c) Advanced control strategy level
d) Providing artificial intelligence
Answer: a
5. Microprocessor-based electrical motors are used for ____
a) prediction of fault in the system
b) correction before the fault occurs
c) actuation purpose in robots
d) providing intelligence
Answer: c
7. Which phase of a mechatronics system consists of hardware designing?
a) Prototyping
b) Modelling
c) Simulation
d) Deployment
Answer: a
Answer: c
9. Describing the behaviour characteristics through block diagram is done in ____
a) modelling and simulation
b) prototyping
c) deployment
d) design optimization
Answer: a
10. Prototyping involves ____
a) conceptual design
b) replacing non-computer systems with actual hardware
c) database for maintaining project information
d) sub models for eventual reuse
Answer: b