Scribd
Upload
43 views3 pages

DTS QP Prelims

The document outlines questions for an exam on the design of transmission systems. It includes questions on topics like hydrodynamic journal bearings, ball bearings, brakes, clutches, gearboxes, and hybrid electric vehicles. Students are asked to explain concepts, derive equations, perform calculations, draw diagrams, and discuss parameters for transmission component selection and design.

Uploaded by

Ramjan Shidvankar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
43 views3 pages

DTS QP Prelims

The document outlines questions for an exam on the design of transmission systems. It includes questions on topics like hydrodynamic journal bearings, ball bearings, brakes, clutches, gearboxes, and hybrid electric vehicles. Students are asked to explain concepts, derive equations, perform calculations, draw diagrams, and discuss parameters for transmission component selection and design.

Uploaded by

Ramjan Shidvankar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Siddhant College of Engineering , End Term Test

T.E. (Mechanical)
DESIGN OF TRANSMISSION SYSTEM
(2019 Pattern) (Semester - II) (302051)

Time : 2½ Hours] [Max.


Marks] : [40]

Instructions to the candidates:


1) Draw neat labeled diagrams wherever necessary.
2) Figures to the right side indicate full marks.
3) Use of non programmable electronic calculator is permitted.
4) Assume Suitable/Standard data if necessary.

Q1) a) Explain design and performance variables of hydrodynamic journal


bearing?
[2]
b) Derive the Petroff’s equation for hydrodynamic bearing. Also state its
limitation?
[2]
c) A single row deep groove ball bearing subjected to 30 second work
cycle that consist Part-I: Radial load 45 kN; Axial Load 12.5 kN; duration
10 second; speed 720 rpm. Take X=l and Y=0 Part II: Radial load 15kN;
Axial Load 6.25 kN; duration 20 second; speed 1440 rpm, take X=0.56
and Y=1.42. Take C0 = 50 kN; C = 68. Find Expected life of the bearing
in hours.
[5]

OR

Q2) a) A single row deep groove ball bearing is subjected to


Fr = 8 kN, F a =3 kN,X = 0.56, Y = 1.4 and N = 1200 rpm. Diameter of shaft is 75 mm,
Bearing number 6315 with C=l 12000 N
Find : i) L10 for 90% reliability;
ii) reliability for 1=20000 hrs.
[2]
b) Derive the Stribecks equation for basic static capacity of bearings. State
the assumption made.
[4]
c) Explain the procedure for selection of the ball bearing from manufacturing
catalogue

[4]
Q3) a) Explain self-energizing block brake and self-locking block brake. [2]
b) Draw a diagram for pivoted Block brake with long shoe’? Write the equation
for reaction on pivot points and Braking torque.
[4]

c) Draw neat sketch diagram of Cone clutch and explain construction and
working. Why is the semi-cone angle of a cone clutch made 12.5°? [4]
OR

Q4) a) What are the two theories applied to friction plates? Why clutches are
usually designed on the basis of uniform wear?
[2]

b) Draw neat sketch diagram, explain construction and working of single


plate clutch and multi plate clutch.
[4]

c) What is the condition of self-locking in differential band brake? Why


should it be avoided in speed-control brakes? What are the advantages
and disadvantages of band brake?
[4]

Q5) a) What is the need of multi-speed gear box in drive system of a machine
tool?
[2]
b) Explain the following parameters considered in kinematic design of multi-
speed gear box;
[2]
i) Range Ratio
ii) Geometric Progression Ratio
iii) Number of spindle speed steps
iv) Number of stages of gear box

c) A 9 speed gear box is to be connected to a motor running at 720 rpm


through a belt drive. The gear box is to have a minimum speed of 31.5
rpm and a maximum speed of 500 rpm. Using standard spindle speeds. [6]

i) Draw the structure and speed diagram for the arrangement;


ii) Draw the gear box;
iii) Select suitable standard pulley diameter for connecting the motor
to the gear box shaft. The standard pulley diameters are based on
R20 series with a diameter starting from 80 mm.

OR

Q6) a) State the law of Harmonic progression used in machine tool gearbox
design. State its advantages and disadvantages. [2]

b) Justify the statement: All the structural formulae of the form


Z = P1(X 1)P2(X2 ) ......... Pn(XN ) cannot be converted into structural diagrams, and
hence are not feasible.
[4]
c) Draw structural diagrams for the following structural formulae and identify
the optimum structural formula out of them. Draw the gearing diagram
for the optimum structural formula.
[4]
i) 2(1) 3(2); ii) 2(3) 3(1);

iii) 3(2) 2(1); iv) 3(1) 2(3)

Q7) a) Classify the Hybrid Electric Vehicle? Explain any one in detail from Series
or Parallel Configuration of Hybrid Electric Vehicles. [4]

b) Explain The basic modes of operations used of Hybrid Electric Vehicles?


Define Degree of Hybridization.
[4]
c) Explain any six components of Hybrid Electric Vehicles? [2]

OR

Q8) a) Explain how the performance analysis carried in Series and parallel Hybrid
Electric Vehicles?
[4]

b) What are the advantages and disadvantages of Hybrid Electric Vehicles? [2]

c) Explain Power Split Device with neat sketch? [4]

You might also like