Mania DC1

user manual
 Measurements are expressed in millimeters.

290

142

312

Ø13

250

© 2003 Martin Professional A/S, Denmark.

All rights reserved. No part of this manual may be reproduced, in any form or by any means,
without permission in writing from Martin Professional A/S, Denmark.

Printed in China.

P/N 35000140, Rev. B.

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Mania DC1 overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
AC power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Overhead mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Changing effect orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Focusing the Mania DC1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Basic service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Lamp maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Mains fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

3
INTRODUCTION 1
Thank you for selecting a Martin Mania DC1. The Mania DC1 is a
luminaire that projects a 53°-beam water-effect in a range of colors at a
user-selectable speed.

SAFETY INFORMATION

Warning! This product is not for household use. It presents risks of

lethal or severe injury due to fire and heat, electric shock, and
falls.

Read this manual before powering or installing the fixture, follow the safety
precautions listed below and observe all warnings in this manual and
printed on the fixture. If you have questions about how to operate the
fixture safely, please contact a Martin distributor for assistance. Refer any
service operation not described in this manual to a qualified technician. Do
not modify the fixture or install other than genuine Martin accessories and
upgrade kits.

Refer servicing to qualified personnel.

Maximum ambient temperature Ta = 40°C(104°F).

See serial label for replacement fuse size and lamp type.

Suitable for mounting on normally flammable surfaces.

Do not look directly into the light.

Risk of fire, electrical shock and burns.

Use only in dry locations.

For indoors use only.

Do NOT block exhaust vents.

Shields, lenses or ultraviolet screens shall be changed if they become

visibly damaged to the extent that their effectiveness is impaired, for
example, by cracks or deep scratches.

4 Mania DC1 user manual

 The lamp shall be changed if it becomes damaged or thermally deformed.

If the external power cord of this luminaire is damaged, it shall be

replaced by a special cord exclusively available from your Martin dealer.

Avoi di ng electric shocks

Warning Always disconnect from mains power before replacing the
lamp, fuses, or any part, and when not in use.

• Before operation ensure that factory setting of voltage and frequency

match local power supply.
• Always ground (earth) the fixture electrically.
• Use only a source of AC power that complies with local building and
electrical codes and has both overload and ground-fault protection.
• Do not expose the fixture to rain or moisture.
• Never operate the fixture with missing or damaged lenses and/or covers.

Protecting yourself and others from burns an d fire

Warning Hot lamp. The exterior of the fixture can become hot. Allow to
cool for at least 5 minutes before handling or opening.

• Surface temperature under steady state condition = 60°C (140° F).

• Minimum distance to flammable material = 0.3 m (1 ft).
• Minimum distance to illuminated surface 1.0 m (3.3 ft).
• Never attempt to bypass the thermostatic switch or fuses. Always replace
defective fuses with ones of the specified type and rating.
• Ensure that the air flow through vents is free and unobstructed.
• Provide a minimum clearance of 0.1 meters (4 inches) around fans and
air vents.
• Never place filters or other materials over the lens or in the optical path.
• The exterior of the fixture can become hot. Allow the fixture to cool for at
least 5 minutes before handling.
• Do not block the fan or vent.
• Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C
(104° F).
• Do not stare directly into the light.
• Never operate the fixture without all lenses and covers installed: an
unshielded lamp emits dangerous UV radiation that can cause burns and
eye damage.

Introduction 5
Preventing injuri es due to fall s
• When suspending the fixture above ground level, verify that the structure
can hold at least 10 times the weight of all installed devices.
• Verify that all external covers and rigging hardware are securely fastened
and use an approved means of secondary attachment such as a safety
cable.
• Block access below the work area whenever installing or removing the
fixture.

UNPACKING
The packing material is carefully designed to protect the fixture during
shipment - always use it to transport the fixture.

The Mania DC1 comes with the following:

• 3-wire IEC power cable

• User manual

MANIA DC1 OVERVIEW

Fuse holder
Mains socket
Mounting bracket
Swivel locks

Cooling fan

Safety cable attachment

AC supply setting

Effect speed
(rotation speed)

Color changing
Effect direction Power on switch
(rotation direction)
Thumb screw (cover lock)
6 Mania DC1 user manual
INSTALLATION 2
AC POWER
Before operation ensure that factory setting of voltage and frequency
match local power supply.

Always ground (earth) the fixture electrically.

Use only a source of AC power that complies with local building and
electrical codes and has both overload and ground-fault protection.

Note: If the external power cord of this luminaire is damaged, it

shall be replaced by a special cord exclusively available from
your Martin dealer.

Configuring for local mains power

The Mania DC1 has a switch-selectable power supply that can operate in
the following voltage ranges at 50-60 Hz:

• 115 - 120 volts (setting 115)

• 220 - 240 volts (setting 230)

Warning Do not operate the fixture on a power supply that falls outside
of these ranges.

Select the operating range using the AC supply switch at the rear of the
fixture.

AC supply setting

Installation 7
Installing a plug on the mains lead
Warning! For protection from dangerous electric shock, the fixture must
be grounded (earthed). The AC mains supply shall have
overload and ground-fault protection.

Important! Verify that the feed cables are undamaged and rated for the
current requirements of all connected devices before use.

The fixture’s mains lead may require a grounding-type cord cap that fits
your power distribution cable or outlet. Consult a qualified electrician if you
have any doubts about proper installation.

Following the cord cap manufacturer’s instructions, connect the

appropriate wires to ground (earth), live, and neutral. The following table
below shows some common wire identification schemes.

Function Wire (EU) Wire (US)

live brown black
neutral blue white
ground yellow/green green

Applying power

1 Connect the mains power cable to the fixture at the 3-prong IEC male
input socket on top of the fixture.

Mains socket

Power on switch

2 Turn the power on using the power-on switch.

8 Mania DC1 user manual

 OVERHEAD MOUNTING
The Mania DC1 can be hung overhead with a clamp (not included).

Warning! Block access below the work area before proceeding.

Always use a secure means of secondary attachment.

For indoors use only.

To hang the Mania DC1 on an overhead support:

1 Verify that the structure can support at least 10 times the weight of all
installed fixtures, clamps, cables, auxiliary equipment, and other items.
2 If hanging the fixture with a rigging clamp, verify that the clamp is
undamaged and is designed for the fixture’s weight. Bolt the clamp
securely to the mounting bracket on the fixture with a grade 8.8
(minimum) M12 bolt and lock nut, or as recommended by the clamp
manufacturer, through the clamp hole in the mounting bracket.
3 If permanently installing the fixture, verify that the hardware (not included)
and mounting surface can bear at least 10 times the fixture’s weight.
4 Working from a stable platform, clamp or fasten the fixture to the
structure.
5 Install a safety cable that can hold at least 10 times the weight of the
fixture through the safety cable attachment point on the fixture.
Loosen the swivel locks, tilt the fixture to the desired angle, and retighten.
Swivel locks

Safety cable
attachment point

Installation 9
 CHANGING EFFECT ORIENTATION
When installing the fixture in a location where the mounting bracket is
underneath the fixture you can use the Rotation Direction switch to ensure
that the effect projected is “falling” water.

10 Mania DC1 user manual

OPERATION 3
CONTROLS
Use the controls at the back of the fixture to:

• Turn the fixture on (I).

• Stop (0) or start (II) color changing.
• Change effect (rotation) direction - clockwise (CW) or counter-clockwise
(CCW). This is used to ensure that the effect projected is “falling” water.
• Adjust effect (rotation) speed. This dial is used to adjust the speed of the
water effect.

Power on switch

Effect speed
(rotation speed)

Effect direction
(rotation direction)
Color changing

Operation 11
 FOCUSING THE MANIA DC1
The focus is adjusted using the mechanism next to the lens. Pull the
mechanism out, or push it in, until a sharp image is acquired.

12 Mania DC1 user manual

BASIC SERVICE 4
This chapter describes the maintenance procedures that you can perform
yourself.

Warning The exterior of the fixture can become hot. Always disconnect
the fixture from AC power and allow to cool for at least 5
minutes before handling or opening.

CLEANING
Regular cleaning of the elements in the optical path, as well as the air
vents, is vital to maintaining the operational quality of the Mania DC1.

Important! Excessive dust, smoke fluid, and particulate buildup degrades

performance and causes overheating and damage to the
fixture that is not covered by the warranty.

Cleaning the air vents

To maintain adequate cooling, dust must be cleaned from the air vents
periodically. Remove dust from the air vents with a soft brush, cotton
swab, vacuum, or compressed air.

Cleaning optical componen ts

Clean the optical components regularly. The presence of smudges or dust
on optical surfaces can reduce the strength of the light output and the
quality of the effects.

Use care when cleaning optical components and work in a clean, well lit
area. The coated surfaces are fragile and easily scratched. Do not use
solvents that can damage plastic or painted surfaces.

1 Disconnect the fixture from power and allow it to cool for 5 minutes.

Basic service 13
 2 Remove the thumb screw holding the cover in place.

Thumb screw
3 Slide the fixture cover open as far as possible (there is a physical stop
point that prevents access to the power supply section).

4 Vacuum or gently blow away dust and loose particles with compressed air.
5 Remove stuck particles with an unscented tissue or cotton swab
moistened with glass cleaner or distilled water. Do not rub the surface: lift
the particles off with a soft repeated press.
6 Remove smoke, and other, residues with cotton swabs or unscented
tissues moistened with isopropyl alcohol. A commercial glass cleaner may
be used, but residues must be removed with distilled water. Clean with a
slow circular motion from center to edge. Dry with a clean, soft and lint-
free cloth or compressed air.
7 Close the fixture cover and tighten the thumb screw, taking care not to trap
any loose wires.

LAMP MAINTENANCE

Warning Isolate electrically before re-lamping. The lamp shall be

changed if it becomes damaged or thermally deformed.

14 Mania DC1 user manual

Caution Hot lamp.

Only the Philips 12V EFP/8H 100W (type No 6834) lamp is supported
(Martin P/N 97000004). These lamps normally last for 800 hours of
operation.

Warning Installing any other lamp may damage the fixture!

Installing a lamp in the Mani a DC1

1 Disconnect the fixture from power and allow it to cool for 5 minutes.
2 Remove the thumb screw holding the cover in place.

Thumb screw
3 Slide the fixture cover open as far as possible (there is a physical stop
point that prevents access to the power supply section).

Basic service 15
 4 Grasp the old lamp by the reflector and slide it carefully out of the lamp
holder.

5 Pull the socket off the lamp. Do not pull the wires.
6 Push the socket fully onto the pins of the new lamp.
7 Clean the glass bulb and reflector with a cloth, particularly if your fingers
touched the glass. A clean, lint-free cloth wetted with alcohol is best.
8 Gently push the lamp into the holder until it snaps into place.
9 Close the fixture cover and tighten the thumb screw.

MAINS FUSE
The Mania DC1 uses a time-delay fuse for protection against current
overload. An indication that the fuse may have blown is that when power
is applied and the lamp is switched on, no light is produced.

If the fuse blows repeatedly, there is a fault with the unit that requires
service by a Martin technician.

Never bypass the fuse or replace it with one of another size or rating.

Replacing the main fuse

1 Unplug the mains cable from the input socket and allow the fixture to cool
for 5 minutes.
2 Pry open the fuse holder (located next to the mains power connector) with
a flat-head screwdriver and remove the fuse.
3 Replace the fuse with one of the same type. The fuse rating is listed on
the serial number label and in “Specifications” on page 18.
4 Replace the fuse holder.

16 Mania DC1 user manual

TROUBLESHOOTING 5
problem probable cause(s) suggested remedy

No light No power to the fixture Check connections

Blown fuse If power is applied and the

lamp is switched on, but
does not light, then check
and replace fuse if
necessary.

Burned out lamp Install new lamp

Fixture to hot Allow to cool

Improve air flow around
fixture

No action Electrical malfunction Refer to a Martin service

technician

Fuse blows repeatedly Electrical malfunction Refer to a Martin service

technician

Troubleshooting 17
S PECIFICATIONS A
PHYSICAL
Size without mounting bracket (LxWxH) . .312 x 250 x 142mm (12.3 x 9.8 x 14.2in)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.3 kg (14lb)

CONSTRUCTION
Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . steel and aluminum

THERMAL
Exterior surface temperature under steady state condition. . . . . . . . . 60°C (140°F)
Time required to cool before handling. . . . . . . . . . . . . . . . . . . . . . at least 5 minutes
Maximum ambient temperature (Ta) . . . . . . . . . . . . . . . . . . . . . . . . . . 40° C (104°F)

INSTALLATION
Minimum distance to flammable material . . . . . . . . . . . . . . . . . . . . . . . . .0.3 m (1ft)
Minimum distance to illuminated surface . . . . . . . . . . . . . . . . . . . . . . . 1.0 m (3.3ft)
Minimum clearance around air vents . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.1 m (4in)

ELECTRICAL
Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-prong IEC male socket
AC Power . . switch selectable, operating ranges 115-120 V / 220-240 V, 50-60 Hz
Main fuse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 AT (time delay),

TYPICAL POWER AND CURRENT

120 V, 50 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 W, 1 A
120 V, 60 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118 W, 1 A
230 V, 50 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 W, 0.5 A
230 V, 60 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 W, 0.5 A
240 V, 50 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119 W, 0.5 A
240 V, 60 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118 W, 0.5 A

CONTROL AND PROGRAMMING

Effect rotation direction
Effect rotation speed
Color changing on/off

PHOTOMETRICS
Beam angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53°

18 Mania DC1 user manual

INCLUDED ITEMS - US VERSION
2 m (6.5 ft) US mains cable 18AWG with US male connector (UL approved)
Philips 12V EFP/8H 100W lamp
User manual

INCLUDED ITEMS - NON-US VERSION

3 m (9.8 ft) EU mains cable 3x1.0mm2 with Schuko male connector
3 m (9.8 ft) EU mains cable 3x1.0mm2 with no male connector
Philips 12V EFP/8H 100W lamp
User manual

ACCESSORIES
Philips 12V EFP/8H 100W lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 97000004
Half-coupler clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 91602005
Fuse (2 AT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 05020009

ORDERING INFORMATION
Mania DC1 US version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .P/N 90430011
Mania DC1 non-US version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 90430010

Specifications 19
www.martin.dk • Olof Palmes Allé 18 • 8200 Aarhus N • Denmark
Tel: +45 8740 0000 • Fax +45 8740 0010