AEI"

IN'TRODUCTION

SECURITY KEYPAD
DUAL OUTPUT SYSTEMS

For Door Strike and Security Control Applications

The DK-9510E is a sejf-contained dual-output security keypad designed for electric door strike and security control applications. Because it employs E PROM the stored data is nonvolatile in case of power failure. Over 100 million combinations are possible for the user codes (code 1 and code 2) and the master code (it also acts as the super user code). The user code 1 can be altered to act as a duress code to activate the duress output for reporting duress to an alarm system or to a telephone dialler. The keypad can be configured to have different operation combinations by using the two user code outputs, such as utilising code 1 for door strike and code 2 for alarm ON-OFF control; or making code 1 for alarm ON-OFF control and code 2 for reporting panic event to an alarm system.

PINK LED AMBER LED LED WHITE YELLOW LIGHT BLUE GREEN GREY BLACK RED

WHITEIBROWN (COM) OUTPUT 2 RELAY WHITEIRED (COM)

LIGHT GREEN HITEIORANGE

1
-

OUTPUT 1 RELAY

(N.C.)

--

<

--

- TAMPER SWITCH
- DAP JUMPER - GROUND (-) - DURESS OUTPUT

12V DC POWER:

Connect to 12V DC power supply. The (-) supply is the grounding point of the keypad.

* OUTPUT RELAY 1:
5 Amp dry relay contacts, with Normally Open (N.O.) and Normally Closed (N.C.) terminals. This relay is prepared for door strike or alarm ON-OFF control connection. Use the N.O. contact for door strike connection. If for alarm ON-OFF control, connect the appropriate pair of these terminals (N.C. or N.O.) to the remote ARMIDISARM terminals on your alarm system; consult the manual for your alarm system. N.O. or N.C. loop is possible. Relay contact is programmable for momentary or start/stop operation.

* OUTPUT RELAY 2
1 AMP dry relay contacts, with Normally Open(N.0.) and Normally Closed (N.C.) terminals. This relay is prepared for alarm ON-OFF control or reporting panic event connection. Connect the appropriate pair of these terminals to the remote ARMIDISARM terminals on your alarm system for alarm ON-OFF control; or to the panic124 hour emergency loop for panic triggering. N.O. or N.C. loop connection is possible. Relay contact is programmable for momentary or start/stop operation.

* DURESS OUTPUT
An NPN transistor Open Collector output. It switches to (-) supply when the Duress Code is entered. Output transistor ratings - Ic max: 100mA sink. Vce max: 25V DCI

THE FACTORY S T DATA E

For the owner's convenience in programming at the first time, the factory has put a MASTER CODE 0000 into the keypad. Except for this code, no other useful code or data has been put into the keypad. The owner has to put his own UNIQUE CODES and DATA into the keypad before use.

IMPORTANT NOTE TO OWNER

To compromise security, in all cases, the owner should program a PERSONAL MASTER CODE for his keypad in order to invalidate the factory set 0000 master code.

PROGRAMMING THE KEYPAD EXAMPLE

1) REQUIREMENT - The following data is required to be stored: a) Change the factory set Master Code 0000 to a Personal Master Code 3289 b) Set User Code 1 in 8321 c) Set User Code 2 in B54 d) Set relay output 1 in Momentary Mode, 5 seconds e) Set relay output 2 in Start/Stop Mode without accelerated code f) Set keypad to lock for 30 seconds after 10 successive false codes

Em E n mI a rn
~

2) PROGRAMMING - Put the required data above into the keypad:

Enter in programming mode by the factory set master code.

ZBS! has been stroed as the new Personal Master code & Super User code.
&J has been stored as User Code 1 and Duress Code. 2 i

W has been stored as User Code 2

~~m EEIm
I 3

Relay output 1 has been set in Momentary Mode, 5 seconds. Relay output 2 has been set in StartIStop Mode without accelerated code. The keypad has been set to lock for 30 seconds after 10 successive false codes

Programming is finished. "All the required dats above-tore&. NOTE: In case of wrong entry during programming, cancel it with key #, or wait 10 seconds, then re-enter.

USING THE KEYPAD EXAMPLE TAKING THE STORED DATA ABOVE AS REFERENCE
1) To enter command to activate relay output 1, enter the user code 1 and validate via #.

~~IEnlm
EElHBB
E l I H

Relay output 1 activates for 5 seconds 2) To enter command to activate relay output 2, enter the user code 2 and validate via #.

Relay output 2 starts 3) The Personal Master Code is also the SUPER USER CODE for relay output 1 and 2. The owner can use only ONE code to operate the two outputs. To command outputs 1 and 2, enter the Personal Master Code into the keypad and validate via # and the corresponding output number. Relay output 1 activates for 5 seconds

EmHzI~m

Relay output 2 starts 4) The DURESS CODE does not need to be programmed. The keypad determines it automatically by increasing the first digit of the User Code 1 by TWO units. e.g. If we have the User Code 1 is 1234, then the keypad will determine the Duress Code as 3234. In the above programming example, we have made User Code 1 as 8321, the Duress Code has been determined as 0321 automatically by the keypad. To command the DURESS OUTPUT, enter the Duress Code & validate via #. Duress output activates, and relay output 1 activates for 5 seconds. The Duress code has a double action; it controls the relay output 1 at the same time as the User Code and activates the Duress Output. Only by entering the User Code 1 can you deactivate the Duress Output. The Duress Code can always activate and deactivate the relay output 1, but can not deactivate the Duress Output.

5) Try to put some (1 to 8 digits) random false codes to the keypad. The keypad generates 5 beeps for each unsuccessful code entry after the # button is pressed. The keypad locks for 30 seconds after 10 successive false codes are entered. Normal operation will be resumed after the 30 seconds has elapsed.

Programming the keypad for other operation modes

6) To access the programming mode, enter your Personal Master Code and validate via *.

El

The keypad is in programming mode & ready to receive new data.

7 ) Set relay output 1 in StarVStop Mode with Accelerated Code.

mk zl

Relay output 1 has been changed from Momentary to StarVStop with Accelerated code

8) Set keypad to activate Duress Output after 10 successive false codes.

The keypad has been changed from 30 second lockup to activating Duress Output

9) To leave programming mode, press *

The keypad is back to operation mode. The reprogrammed data has been stored

Using the keypad with the re-programmed data

10) The relay output 1 has been programmed in StartIStop mode with Accelerated Code. It is possible to activate the output 1 with ONLY the First Two Digits of the user code 1 Deactivation of the output always requires entering the complete code. e.g. Complete User Code 1 : 8321 Accelerated Code 83

Ia l Zm 0000
SPECIFICATIONS
Operating Voltage: Current Drain: Duress Output: -- - -. Codes Available: Code Combinations: Relay Outputs: Dimensions: Weight:

2
I

# " -

Relay output 1 starts (activates) Relay output 1 stops (deactivates)

11) Try to put some (1 to 8 digits) false codes to the keypad. The keypad will activate the Duress Output after 10 successive false codes are entered. To reset (deactivate) the Duress Output, you are required to enter User Code 1.

12V DC (10-14VDC) 10-100mA NPN transistor open collector switches to ground (-) when activates, 100mAl25V DC mat User 1 & 2, Super User, Master, Duress and Accelerated Codes .-- - ~ . -11,111,100 Output 1 - 5Amp, Output 2 - 1Amp, N.C. & N.O. dry contacts, 30V DC max 117(H)mm x 74(W)mm x 48(D)mm 180g (nett), 2309 (gross) approx.
~ ~

~-

. .

Specifications are subject to change for modification without notice.

"

i
'

TYPICAL APPLICATION
OUTPUT 1 .OUTPUT 2

ik L \

- - - - - - - DOOR STRIKE - - - - - - - ALARM CONTROL DURESS OUTPUT- - - DIALEW PANIC

AMBER /RED LED- ALARM STATUS INDICATORS GREEN LED -DOOR OPEN

A L R M CONTROL PANEL

WHITEIORANGE DURESS OUTPUT WHITE/RED (COM)

DK - 9510E

DOOR STRIKE

AEI ADVANCED ELECTROIVICS INDUSTRY LTD

SINCE 1979

* N.C. TAMPER:
Normally Closed contact when the keypad is secured on the box. It is open when keypad is separated from the box. Connect these terminals in series with the tamper/panic/24hour emergency circuit loop on your alarm system if necessary.

* RED, AMBER & GREEN LED LAMPS:

Three on-board LED lamps area available. They are prepared for free connections. We suggest that you connect these LED lamps to the remote indicator terminals on your alarm control panel. Be sure to observe the polarity (+ & -). Each of the on-board LED lamps are equipped with 1.5K Ohm current limiting resistor.

THE PACIFIER TONES

The built-in buzzer generates the following tones for operation status:

STATUS
1. 2. 3. 4.

TONES
1 beep 2 beeps 5 beeps Continuous beeps

Successful key entry Successful code entry Unsuccessful code entry DAP jumper not replaced

THE DAP JUMPER (DIRECT ACCESS TO PROGRAMMING)

If the Personal Master Code is forgotten, use the DAP jumper to override the forgotten code permitting direct entry into programming mode. You are required to apply the following procedure precisely: 1. Disconnect power supply 2. Displace the DAP jumper from OFF to ON. 3. Reconnect power supply (buzzer is activated). ' 4. Put the DAP jumper back to OFF position (this done, the buzzer is de-activated). 5. The Keypad is in programming mode and ready to receive your new programming data. 6. Enter the new programming data starting from Section (6) in the summary chart shown below.

----PRO-GRAMMING
Entry of Code 0000

THE KYPAD SUMMARY CHART

A) Use the factory set master code entry in programming When starting for the first time only.
Validation

-- - -

Comments Enter in programming mode by factory set master code

B) Programming Recording of personal master code & user codes User programming
Access Keys 0 1
2

Entry of Codes From 1 to 8 Digits From 1 to 8 Digits From 1 to 8 Digits

Validation #
# #

Comments Personal Master Code & Super User Code User Code 1 & Duress Code (For door strike or alarm ON-OFF) User Code 2 (For alarm ON-OFF or panic event reporting)

C) Programming Configuration of relay outputs Installer programming

Access Keys 4 0
4 1

Code Duration From 1 to 999

4 5 5 5

2 0 1 2

Validations # # #
#

From 1 to 999

# #

Comments Output 1 in MOMENTARY mode from 1 to 999 seconds Output 1 in STARTISTOP mode without accelerated code Output 1 in STARTLSTOP mode with accelecated code Output 2 in MOMENTARY mode from 1 to 999 seconds Output 2 in STARTISTOP mode without accelerated code Output 2 in STARTISTOP mode with accelerated code

D) Programming Safety Installer Programming

Access Keys 7 0 Validation # # # Comments After 10 successive false codes, the keypad locks for 30 seconds After 10 successive false codes, the DURESS output is activated (low) Disappearance of the 2 above securities

7 1
7 2

E) Leave programming mode

Validation

Comments The Keypad leaves programming mode, and is in OPERATION mode, ready for daily use. 2