BTA10, BTB10

T1035, T1050
Datasheet

10 A Snubberless™, logic level and standard Triacs

A2 Features
• Medium current Triac
G • Low thermal resistance with clip bonding
A1 • Low thermal resistance insulation ceramic for insulated BTA
A2 • High commutation (4Q) or very high commutation (3Q, Snubberless™)
capability
• BTA series UL1557 certified (file ref: 81734)
G G • Packages are RoHS (2002/95/EC) compliant
A2 A2
A1 A1

TO-220AB TO-220AB Ins.

A2 Description
Available either in through-hole or surface mount packages, the BTA10, BTB10 and
T10xx Triac series are suitable for general purpose mains power AC switching. They
A2
G can be used as ON/OFF function in applications such as static relays, heating
D²PAK
A1 regulation or induction motor starting circuit. They are also recommended for phase
control operations in light dimmers and appliance motors speed controllers.
The Snubberless™ versions (W suffix and T10xx) are especially recommended for
use on inductive loads, because of their high commutation performance. By using an
internal ceramic pad, the Snubberless™ series provide an insulated tab (rated at
2500 VRMS) complying with UL standards (file reference: E81734).

Product status link

BTA10, BTB10, T1035, T1050

Product summary

IT(RMS) 10 A

VDRM/VRRM 600 and 800 V

IGT 25 to 50 mA

DS3165 - Rev 9 - March 2019 www.st.com

For further information contact your local STMicroelectronics sales office.
 BTA10, BTB10, T1035, T1050
Characteristics

1 Characteristics

Table 1. Absolute maximum ratings

Symbol Parameters Value Unit

TO-220AB Tc = 105 °C
IT(RMS) RMS on-state current (full sine wave) 10 A
TO-220AB Ins. Tc = 95 °C

Non repetitive surge peak on-state current (full cycle, Tj F = 50 Hz tp = 20 ms 100

ITSM A
initial = 25 °C) F = 60 Hz tp = 16.7 ms 105

I2t I2t value for fusing tp = 10 ms 55 A2s

Critical rate of rise of on-state current
dl/dt F = 120 Hz Tj = 125 °C 50 A/µs
IG = 2 x IGT , tr ≤ 100 ns

VDRM/VRRM +
VDSM/VRSM Non repetitive surge peak off-state voltage tp = 10 ms Tj = 25 °C V
100
IGM Peak gate current tp = 20 µs Tj = 125 °C 4 A

PG(AV) Average gate power dissipation Tj = 125 °C 1 W

Tstg Storage junction temperature range -40 to +150 °C

Tj Operating junction temperature range -40 to +125 °C

Table 2. Static electrical characteristics

Symbol Test conditions Tj Value Unit

VT(1) ITM = 14 A, tp = 380 µs 25 °C Max. 1.55 V

VTO threshold on-state voltage 125 °C Max. 0.85 V

RD Dynamic resistance 125 °C Max. 40 mΩ

25 °C 5 µA
IDRM/IRRM VDRM = VRRM Max.
125 °C 1 mA

1. For both polarities of A2 referenced to A1

Table 3. Electrical characteristics (Tj = 25 °C, unless otherwise specified) - Snubberless™ (3 quadrants)

T1050
BTA10-xCW
Symbol Parameters Quadrant T1035 BTA10-xBW Unit
BTB10-xCW
BTB10-xBW

IGT I - II - III Max. 35 50 mA

VD = 12 V, RL = 33 Ω
VGT I - II - III Max. 1.3 V

VGD VD = VDRM, RL = 3,3 kΩ, Tj = 125 °C I - II - III Min. 0.2 V

IH IT = 500 mA I - II - III Max. 35 50 mA

I - III Max. 50 70
IL IG = 1.2 IGT mA
II Max. 80 60 80

dV/dt(2) VD = 67 % VDRM gate open, Tj = 125 °C Min. 500 1000 V/µs

DS3165 - Rev 9 page 2/12

 BTA10, BTB10, T1035, T1050
Characteristics

T1050
BTA10-xCW
Symbol Parameters Quadrant T1035 BTA10-xBW Unit
BTB10-xCW
BTB10-xBW

(dI/dt)c(2) Without snubber, Tj = 125 °C Min. 5.5 9 A/ms

1. Minimum IGT is guaranteed at 5 % of IGT max.

2. For both polarities of A2 referenced to A1

Table 4. Electrical characteristics (Tj = 25 °C, unless otherwise specified) - standard Triac (4 quadrants)

Value
Symbol Parameters Quadrant Unit
C B

I - II - III Max. 25 50
IGT(1) mA
VD = 12 V, RL = 33 Ω IV Max. 50 100
VGT All Max. 1.3 V

VGD VD = VDRM, RL = 3,3 kΩ, Tj = 125 °C I - II - III Min. 0.2 V

IH(2) IT = 500 mA I - II - III Max. 25 50 mA

I - III Max. 40 50
IL IG = 1.2 IGT mA
II Max. 80 100

dV/dt(2) VD = 67 % VDRM gate open, Tj = 125 °C Min. 200 400 V/µs

(dV/dt)c(2) (dI/dt)c = 4.4 A/ms, Tj = 125 °C Min. 5 10 V/µs

1. Minimum IGT is guaranteed at 5 % of IGT max.

2. For both polarities of A2 referenced to A1

Table 5. Thermal resistance

Symbol Parameters Value Unit

TO-220AB / D²PAK 1.5

Rth(j-c) (typ.) Junction to case (AC)
TO-220AB insulated 2.4
°C/W
Junction to ambient (S(1) = 2 cm²) D²PAK 45
Rth(j-a) (max.)
Junction to ambient TO-220AB / TO-220AB ins 60

1. Copper surface under tab.

DS3165 - Rev 9 page 3/12

 BTA10, BTB10, T1035, T1050
Characteristics (curves)

1.1 Characteristics (curves)

Figure 2. Maximum power dissipation versus on-state Figure 3. RMS on-state current versus case temperature
RMS current (full cycle) (full cycle)

P(W) I T(RMS) (A)

13 12
12 11
11 10 BTB/T10
10 9
9 BTA
8
8
7
7
6
6
5 5
4 4
3 3
2 2
1
IT(RMS)(A) 1 Tc(°C)
0 0
0 1 2 3 4 5 6 7 8 9 10 0 25 50 75 100 125

Figure 4. Relative variation of thermal impedance versus

pulse duration Figure 5. On-state characteristics (maximum values)
ITM(A)
K = [Zth/Rth] 100
Tj = Tj max.
Tj max.
1E+0
Zth(j-c) Vto = 0.85 V
Rd = 40 mΩ

Zth(j-a) 10
1E-1 Tj = 25 °C

VTM(V)
tp(s) 1
1E-2
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
1E-3 1E-2 1E-1 1E+0 1E+1 1E+2 5E+2

Figure 6. Surge peak on-state current versus number of

cycles Figure 7. Non repetitive surge peak on-state current
versus sinusoidal pulse width (tP < 10 ms)
ITSM(A)
ITSM(A) 1000
110 Tj initial=25°C
100
90
t=20ms
80 Non repetitive ITSM
Tj initial=25°C One cycle dI/dt limitation:
70 50A/µs
60 100
50
Repetitive
40 TC=95°C
30
20
10 Number of cycles t p (ms)
0 10
1 10 100 1000 0.01 0.10 1.00 10.00

DS3165 - Rev 9 page 4/12

 BTA10, BTB10, T1035, T1050
Characteristics (curves)

Figure 8. Relative variation of gate trigger current, holding

Figure 9. Relative variation of critical rate of decrease of
current and latching current versus junction temperature
main current versus (dV/dt)c (typical values)
(typical values)

IGT,IH,IL[Tj] / IGT,IH,IL[Tj = 25 °C] (dl/dt)c [(dV/dt)c / specified (dl/dt)c

2.5 2.0

1.8
2.0 C
1.6
IGT B
1.4
1.5
1.2 BW/CW/T10xx
1.0 IH and IL 1.0

0.8
0.5
0.6
Tj (°C) (dV/dt)c (V/µs)
0.0 0.4
-40 -20 0 20 40 60 80 100 120 140 0.1 1.0 10.0 100.0

Figure 10. Relative variation of critical rate of decrease of Figure 11. D²PAK thermal resistance junction to ambient
main current versus junction temperature versus copper surface under tab

Rth(j-a) (°C/W)
(dl/dt)c [Tj] / (dl/dt)c [Tj = 125 °C] 80
6 D²PAK
70
Epoxy printed board FR4, copper thickness = 35 µm
5 60

4 50

40
3
30
2
20
1
10
Tj(°C) SCu (cm²)
0 0
0 25 50 75 100 125 0 5 10 15 20 25 30 35 40

DS3165 - Rev 9 page 5/12

 BTA10, BTB10, T1035, T1050
Package information

2 Package information

In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK®
packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions
and product status are available at: www.st.com. ECOPACK® is an ST trademark.

2.1 D²PAK package information

Figure 12. D²PAK package outline

E A E1
c2 E2
L2

D1
D
H

1 2 3

D2
L3

b2

e
b Max resin gate protrusion: 0.5 mm (1)
G

A1
A2

A3

R
L

Gauge Plane

c
V2
(1) Resin gate is accepted in each of position shown on the drawing, or their symmetrical.

Table 6. D²PAK package mechanical data

Dimensions

Ref. Millimeters Inches(1)

Min. Typ. Max. Min. Typ. Max.

A 4.30 4.60 0.1693 0.1811

A1 2.49 2.69 0.0980 0.1059
A2 0.03 0.23 0.0012 0.0091
A3 0.25 0.0098
b 0.70 0.93 0.0276 0.0366
b2 1.25 1.7 0.0492 0.0669

DS3165 - Rev 9 page 6/12

 BTA10, BTB10, T1035, T1050
D²PAK package information

Dimensions

Ref. Millimeters Inches(1)

Min. Typ. Max. Min. Typ. Max.

c 0.45 0.60 0.0177 0.0236

c2 1.21 1.36 0.0476 0.0535
D 8.95 9.35 0.3524 0.3681
D1 7.50 8.00 0.2953 0.3150
D2 1.30 1.70 0.0512 0.0669
e 2.54 0.1
E 10.00 10.28 0.3937 0.4047
E1 8.30 8.70 0.3268 0.3425
E2 6.85 7.25 0.2697 0.2854
G 4.88 5.28 0.1921 0.2079
H 15 15.85 0.5906 0.6240
L 1.78 2.28 0.0701 0.0898
L2 1.27 1.40 0.0500 0.0551
L3 1.40 1.75 0.0551 0.0689
R 0.40 0.0157
V2 0° 8° 0° 8°

1. Dimensions in inches are given for reference only

Figure 13. D²PAK recommended footprint (dimensions are in mm)

16.90

10.30 5.08

1.30

3.70
8.90

DS3165 - Rev 9 page 7/12

 BTA10, BTB10, T1035, T1050
TO-220AB non ins. and insulated package information

2.2 TO-220AB non ins. and insulated package information

Figure 14. TO-220AB non ins. and insulated package outline

B C

b2
Resin gate 0.5 mm I
max. protusion(1)
L
F

I4

l3

a1 c2

l2
a2

M
b1 Resin gate 0.5 mm c1
max. protusion(1)
e
(1)Resin gate position accepted in one of the two positions or in the symmetrical opposites.

Table 7. TO-220AB non ins. and insulated package mechanical data

Dimensions

Ref. Millimeters Inches1

Min. Typ. Max. Min. Typ. Max.

A 15.20 15.90 0.5984 0.6260

a1 3.75 0.1476
a2 13.00 14.00 0.5118 0.5512
B 10.00 10.40 0.3937 0.4094
b1 0.61 0.88 0.0240 0.0346
b2 1.23 1.32 0.0484 0.0520
C 4.40 4.60 0.1732 0.1811

DS3165 - Rev 9 page 8/12

 BTA10, BTB10, T1035, T1050
TO-220AB non ins. and insulated package information

Dimensions

Ref. Millimeters Inches1

Min. Typ. Max. Min. Typ. Max.

c1 0.49 0.70 0.0193 0.0276

c2 2.40 2.72 0.0945 0.1071
e 2.40 2.70 0.0945 0.1063
F 6.20 6.60 0.2441 0.2598
I 3.73 3.88 0.1469 0.1528
L 2.65 2.95 0.1043 0.1161
I2 1.14 1.70 0.0449 0.0669
I3 1.14 1.70 0.0449 0.0669
I4 15.80 16.40 16.80 0.6220 0.6457 0.6614
M 2.6 0.1024

1. Inch dimensions are for reference only.

DS3165 - Rev 9 page 9/12

 BTA10, BTB10, T1035, T1050
Ordering information

3 Ordering information

Figure 15. BTA10 and BTB10 series ordering information scheme

BT A 10 - 600 BW RG

Triac
Insulation
A = Insulated
B = Non-insulated
Current
10 = 10 A
Voltage
600 = 600 V
800 = 800 V
Sensitivity and type
B = 50 mA standard BW = 50 mA Snubberless™
C = 25 mA standard CW = 35 mA Snubberless™
Packing mode
RG = Tube

Figure 16. T10xx series ordering information scheme

T 10 50 - 8 G - TR

Triac

Current
10 = 10 A
Sensitivity
50 = 50 mA
35 = 35 mA
Voltage
800 V
600 V
Package
G = D²PAK
Packing mode
(blank) = Tube
-TR = Tape and reel

Table 8. Ordering information

Order code Marking Package Weight Base qty. Delivery mode

BTA10-600BRG BTA10-600B
BTA10-600CRG BTA10-600C
BTA10-600BWRG BTA10-600BW
TO-220AB Ins.
BTA10-600CWRG BTA10-600CW
2.3 g
BTA10-800BWRG BTA10-800BW
50 Tube
BTA10-800CWRG BTA10-800CW
BTB10-600BWRG BTB10-600BW
TO-220AB
BTB10-800BWRG BTB10-800BW
T1035-6G T1035-6G
T1050-8G T1050-8G
D²PAK 1.50 g
T1035-6G-TR T1035-6G
1000 Tape and reel 13"
T1050-8G-TR T1050-8G

DS3165 - Rev 9 page 10/12

 BTA10, BTB10, T1035, T1050

Revision history

Table 9. Document revision history

Date Revision Changes

Sep-2002 5A Last update.

TO-220AB delivery mode changed from bulk to tube. ECOPACK statement
13-Feb-2006 6
added.
06-Feb-2017 7 Added D²PAK package information.
Updated Table 3. Electrical characteristics (Tj = 25 °C, unless otherwise
specified) - Snubberless™ (3 quadrants), Section 3 Ordering information and
15-Mar-2018 8 Section 2.1 D²PAK package information.
Added RPNs T1035 and T1050.
01-Mar-2019 9 Updated Links syntax.

DS3165 - Rev 9 page 11/12

 BTA10, BTB10, T1035, T1050

IMPORTANT NOTICE – PLEASE READ CAREFULLY

STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST
products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST
products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of
Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2019 STMicroelectronics – All rights reserved

DS3165 - Rev 9 page 12/12