FCL/FCLS Flexible Flanged Shaft Coupling

●● The most popular flexible shaft coupling in Japan

that is compliant with JIS B 1452 - 1991 "Flexible
FCL
■■ Product Standard ■■ Alignment adjustment
The product standard of the flexible flanged shaft ①Although the flexible flanged shaft coupling permits
Flanged Shaft Couplings". couplings is compliant with JIS B 1452 - 1991 "Flexible misalignment and transmits torque, if the
●● Simple structure comprised of a flange and Flanged Shaft Couplings". misalignment exceeds the allowable value,
coupling bolts. Easy-to-mount. ●● Allowable value of the run-out of the joint outer vibration may occur or the life may be rapidly
●● Bushings can be replaced just by removing diameter to the shaft hole center, and that of the shortened. Be sure to perform alignment
coupling bolts. This makes maintenance and joint surface near the outer diameter 0.03mm adjustment.
service easy. FCLS ●● Allowance of the bolt hole pitch circle diameter ②Shaft center misalignment includes eccentricity
●● While it absorbs misalignment such as eccentricity (parallel error of both shaft centers), argument
and the bushing insertion hole pitch circle
and argument, it prevents noise by absorbing diameter, allowance of the pitch, and the run-out (angle error of both shaft centers), and end-play
torsional vibration. It will not transmit thrust load, ●● Material/Finish (shaft direction movement of the shaft). Adjust the
RoHS tolerance to the shaft bore center Unit：mm
either. FCL FCLS Pitch Circle Diameter and Pitch Circle Diameter shaft alignment so that it will not exceed the
Pitch Circle Diameter
●● Two types are available: Cast Iron FCL and Joint Pitch Allowance Run-out Tolerance allowable value listed in the Dimension/
FC200 or more S25C or more
Main Unit 60 / 67 / 75 ±0.16 0.12
Carbon Steel FCLS . Performance table in this catalog.
Equivalent to SS400 Equivalent to SS400

■■ Structure
Nut 85 / 100 / 115 / 132 / 145 ±0.20 0.14
Trivalent Chromate Treatment Trivalent Chromate Treatment ③The allowable values of the misalignment listed in
170 / 180 / 200 / 236 ±0.26 0.18
Spring Lock SWRH62 SWRH62 the Dimension/Performance table are for the case
Washer 260 / 300 / 355 / 450 / 530 ±0.32 0.22
Washers Trivalent Chromate Treatment Trivalent Chromate Treatment
where any one of eccentricity, argument, and end-
580 / 600 / 670 ±0.40 0.28
NBR NBR
Bushing play occurs independently. Mixing of two or more
Nut B (12) -j1a1〔HS (JIS A)＝70〕 B (12) -j1a1〔HS (JIS A)＝70〕 ●● Dimensional allowance of each part of the joint
Equivalent to SS400 Equivalent to SS400 Unit：mm misalignment causes each of the allowable values
Washer
Trivalent Chromate Treatment Trivalent Chromate Treatment Joint Outside Diameter A - g7 to be reduced to half.
Equivalent to SS400 Equivalent to SS400 Bolt Hole and Bolt a H7 g7 ④Misalignment may occur not only in assembling
Bolt Bolt
Trivalent Chromate Treatment Trivalent Chromate Treatment ＋0.4
Washer Inside Diameter＊1 a - 0 into the device but also due to vibration, thermal
Bushing Inside Diameter, Washer Inside Diameter ＋0.4
0 e9 expansion, and shaft bearing abrasion during
and Bolt Bushing Insertion Area Diameter a1
Spring Washer operation. Therefore, it is recommended to keep
Bushing Insertion Hole M H8 -

Bushing Outside Diameter p - 0 the misalignment one third of the allowable value
－0.4

Bolt Bushing Insertion Area Length m - k12 or less.

＊1： For those with the standard dimensions of 8, it is ＋0.2

0 . ●● Eccentricity, Parallel Offset Misalignment
Each symbol is identical to that shown in the Dimension/

δ
●●

Performance table.
Bush width q dimensional allowance Washer thickness t dimensional allowance
Standard Dimension Allowance Standard Dimension Allowance
＋0.03
14 / 16 / 18 ±0.3 3 －0.43
＋0.1
22.4 / 28 / 40 －0.5 4 ±0.29
＋0.2
56 / 80 －0.6 5 ±0.4
7 ±0.5 ●● Argument, Angular Misalignment
Bush Joint Main body
●● For the allowable length tolerances of non-fitting part sections to
α
be cut, refer to JIS B 0405 tolerance class m.

●● Performance of the Bushing

Characteristics item NBR (Nitrile rubber)
Machine oil Excellent
Gasoline Excellent
Benzine Impossible ●● End-Play
Ketone Impossible
Alcohol Excellent
Weak acid Good
Acid resistance
Strong acid OK
Impact resilience Good
●● Full bore alteration service capability.● Abrasion resistance Excellent x
We modify for individual shaft requirement Aging Resistance Excellent

that will allow you for immediate use. Tensile strength Excellent

Additional Setscrew at Shaft Hole / Keyway ➡ P.xxxx Heat resistance (max. operating temperature, regular use) 90℃

Available / Add'l charge Cold resistance (min. operating temperature, regular use) -20℃

▶ https://www.nbk1560.com ▶ https://www.nbk1560.com